2010 Acura TSX Owners Manual

This indicator comes on when you set the cruise control. See page 298
cruise control.

for information on operating the

or

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the

ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.

AllmodelsexceptCanadianTSXwith 4-cylinderengine This indicator will also come on when the light switch is in AUTO and the lights turn on automatically.

66

2010 TSXSystem Message Indicator

This indicator comes on when there is a system message on the multi- information display. Press the INFO button on the steering wheel (see ) to see the message (see page page ).

71
79

Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.

Low Fuel Indicator

LOW FUEL INDICATOR

This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon. You will also see a ‘‘FUEL LOW’’ message on the multi- information display.

When the indicator comes on, there are about 2.8 U.S. gal (10.5 ) of fuel remaining in the tank. When the needle reaches E, there is a very small amount of fuel in the tank.

Instrument Panel Indicators

Security System Indicator

SECURITY SYSTEM INDICATOR

This indicator comes on when the security system is set. For more information, see page

292

67

2010 TSXGauges

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

MULTI-INFORMATION DISPLAY

U.S. model is shown.

68

2010 TSXTemperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system.

469

If the pointer of the temperature gauge reaches to or above the red mark, you will also see the ‘‘WATER TEMP HOT’’ message on the multi- information display. This will alert you that the engine should be cooled down.

Gauges

69

2010 TSXMulti-Information Display

The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.

There are three types of messages: normal display messages, engine oil life and maintenance messages, and system messages.

You can select the displayed language and also customize some vehicle control settings to your liking with the multi-information display and the three buttons on the steering wheel (see page

71

).

70

Normal Display Messages

Remote transmitter 1 is used.

Remote transmitter 2 is used.

When you unlock and open the driver’s door, the display shows ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ depending on which remote transmitter you use.

AllmodelsexceptCanadianTSXwith 4-cylinderengine The driver’s seat moves to the position stored in that remote transmitter (see page

142

).

If you do not fasten your seat belt, you will see a ‘‘FASTEN SEAT BELT’’ message on the multi- information display when you turn the ignition switch to the ON (II) position.

These messages go off several seconds after the key is inserted into the ignition switch.

2010 TSXSEL/RESET BUTTON

In the multi-information display, the system message is also displayed (see page customize your vehicle control settings (see page

) and you can

78

81

).

MIDDLE SEGMENT

UPPER SEGMENT

INFO BUTTONS (

▲ ▼

With the ignition switch in the ON (II) position, the multi-information display changes as shown on the next page each time you press the INFO ( / ) button or the SEL/ RESET button.

▲ ▼

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

U.S. model is shown.

LOWER SEGMENT

The multi-information display consists of an upper segment, a middle segment and a lower segment.

Multi-Information Display

In the normal display mode, the upper and middle segments display trip computer information, such as fuel economy or average speed. The lower segment displays the odometer/trip meter (A/B), outside temperature, and engine oil life and maintenance item code(s).

CONTINUED

71

2010 TSXMulti-Information Display

Trip Computer (See page 74.)

Outside Temperature (See page 74.)

Engine Oil Life (See page 76.)

U.S. model is shown.

＊

72

: This display will be shown when the

Bluetooth

HandsFreeLink is activated.

＊

HFL (See page 77.)

Tire Pressure for each tire (See page 76.)

: Press the INFO button (

). ▲ ▼

: Press the SEL/RESET button.

2010 TSXOdometer

Trip Meter

U.S.

Canada

TRIP METER A

TRIP METER B

ODOMETER

U.S. model is shown.

The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

Multi-Information Display

When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset.

In the customizing mode, you can set Trip A and average fuel economy A to reset at the same time when you refuel your vehicle (see page ).

89

73

2010 TSXMulti-Information Display

Outside Temperature

U.S.

CANADA

OUTSIDE TEMPERATURE

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

Trip Computer

U.S.

CANADA

This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

INST.MPG(U.S.models)/INST.L/ 100km(Canadianmodels) This shows your instant fuel economy.

You can adjust the outside temperature display (see page

88

).

74

2010 TSXAVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.

You can customize the Trip A and AVERAGE FUEL A reset condition on the multi-information display (see page

89

).

RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles(U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.

ELAPSEDTIME This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset.

If you want to reset the ELAPSED TIME manually, go to the trip computer’s ELAPSED TIME display, and press and hold the SEL/RESET button until the number resets.

You can customize the ELAPSED TIME reset conditions on the multi- information display (see page ).

90

Multi-Information Display

AVERAGESPEED This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.

To reset the AVERAGE SPEED you have traveled, press and hold the SEL/RESET button until the number resets.

75

2010 TSXMulti-Information Display

Engine Oil Life

ENGINE OIL LIFE

Tire Pressure Monitor

U.S.

Canada

This shows the remaining engine oil life. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions. For more information, see page

403

76

When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page

388

2010 TSXTo use the system, your cell phone and the HFL system must be linked. Not all cell phones are compatible with this system. Refer to page for instructions on how to link 304
your cell phone to HFL and how to receive or make phone calls, or visit the acura.com/handsfreelink website. In Canada, visit ca

, or call 1-888-9-ACURA-9.

www.acura.

Bluetooth HandsFreeLink

You can receive or make phone calls from your cell phone through your HandsFreeLink vehicle’s (HFL) system without touching your cell phone.

Bluetooth

Multi-Information Display

77

2010 TSXThe system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.

You will also hear a beep when the system message comes on for the first time.

Most of the messages are displayed for about 5 seconds, and then the normal display returns. If there are several system messages to be shown, the display switches these messages every 5 seconds.

To switch the message(s) before 5
seconds have elapsed, press the INFO ( / ) button on the steering wheel.

▲ ▼

Even if you press the INFO ( / ) ▲ ▼ button, some messages stay on or come on again at regular intervals until the problem is corrected.

If the system message indicator remains lit on the instrument panel, you can see the corresponding message(s) again by pressing the INFO ( / ) button repeatedly.

▲ ▼

Here is a list of all messages:

Multi-Information Display

System Messages

SYSTEM MESSAGE INDICATOR

If there is a problem with your vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.

78

2010 TSXSee page

11

See page

19

See page

19

See page

32

See page

32

U.S.

Canada

U.S.

Canada

U.S.

Canada

See page

153

See page

427

See page

473

U.S.

Canada

Multi-Information Display

See page

471

See page

472

See page

471

See page

384

See page

392

See page

69

CONTINUED

79

2010 TSXMulti-Information Display

See page

388

See page

389

See page

389

See page

389

See page

373

See page

67

6-cylinder models only

U.S.

Canada

See page

65

See page

369

See page

122

See page

122

See page

123

Canadian models only

See page

114

See page

404

See page

405

See page

407

See page

349

See page

423

80

2010 TSXCustomized Settings

DRIVER’S ID

▲ ▼

You can customize some vehicle control settings. To enter the customizing mode, press and hold either INFO button ( / ) for more than 3 seconds. To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park (automatic) or with the parking brake set (manual).

If you turn the ignition switch to the

ACCESSORY (I) or the LOCK (0) position, move the shift lever out of Park (automatic) or release the parking brake (manual), the display will change to the normal screen.

If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFT TO PARK TO CHANGE SETTINGS’’ (automatic) or ‘‘MUST STOP AND SET PARK BRAKE TO CHANGE SETTINGS’’ (manual) message and you cannot change the settings.

You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately. If ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ is not displayed, customizing is not possible.

To have the driver’s ID detected, make sure your remote transmitter is linked to the system and the driver’s door is unlocked with a

Multi-Information Display

corresponding remote transmitter.

See page transmitter to your vehicle.

to link your remote

128

If the remote transmitter is not linked, ‘‘DRIVER UNKNOWN CUSTOMIZE IMPOSSIBLE’’ will be displayed, and you cannot customize the settings.

If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’

If you want to change any vehicle control settings, select CHG SETTING, then press the SEL/ RESET button.

Refer to the table on the following pages about the settings you want to customize.

CONTINUED

81

2010 TSXMulti-Information Display

Group Setup METER SETUP (P.86)

＊

POSITION SETUP (P.92) LIGHTING SETUP (P.94)

Menu Item

Description

Setting Option

Page

LANGUAGE SELECTION

Changes the language used in the display.

ADJUST OUTSIDE TEMP. DISPLAY

Changes the outside temperature reading above or below its current reading.

TRIP A RESET with REFUEL

ELAPSED TIME RESET

Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.

MEMORY POSITION LINK

＊

INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER

AUTO LIGHT SENSITIVITY

＊

Changes the driver’s seat position to a stored setting. Changes how long (in seconds) the interior lights stay on after you close the doors. Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.

Changes the timing of when the headlights come on. The headlight switch needs to be in the AUTO position.

＊

＊

＊

ENGLISH FRENCH SPANISH 5°F − 〜 ± (U.S.) 3°C − 〜 ± (Canada) ON OFF IGN OFF TRIP A ON OFF 60 sec 30 sec 60 sec 30 sec 15 sec MAX HIGH MID ＊

＊

＊

＊

0°F

＊

〜

5°F

0°C

＊

〜

3°C

TRIP B

15 sec

0 sec

LOW MIN

87

88

89

90

93

95

96

97

＊ ＊

Default setting

1 : 2 : All models except Canadian TSX with 4-cylinder engine

82

2010 TSXGroup Setup

DOOR SETUP (P.99)

Menu Item AUTO DOOR LOCK

Changes when the doors automatically lock.

DOOR LOCK MODE

KEYLESS LOCK ACKNOWLEDGMENT

SECURITY RELOCK TIMER

AUTO DOOR UNLOCK

Changes which doors unlock with the remote transmitter in a first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Changes when the doors automatically unlock.

DEFAULT ALL (P.108)

＊ ＊ ＊

1 : 2 : 3 :

Default setting Default setting for automatic transmission Default setting for manual transmission

Set/Cancel all the customized settings as default.

Multi-Information Display

Description

Setting Option

Page

＊

SHIFT FROM P (A/T only) WITH VEH SPD OFF DRIVER DOOR ALL DOORS ON OFF

＊

＊

＊

＊

90 sec 60 sec 30 sec DRIVER DOOR / ALL DOORS OFF SET CANCEL

With SHIFT to P 2
With IGN OFF

＊

＊

100

101

103

104

106

108

83

2010 TSXMulti-Information Display

Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:

METER SETUP POSITION SETUP LIGHTING SETUP DOOR SETUP

＊

＊

: All models except Canadian TSX with 4-cylinder engine

84

When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG SETTING, then press the SEL/ RESET button.

▲ ▼

Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection.

▲ ▼

If you do not make any changes, select ‘‘EXIT.’’ The display returns to the normal display.

If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page

108

2010 TSXAny of the normal displays

: Press the SEL/ RESET button. : Press the INFO button ( ). ▲ ▼ : Press and hold the ). INFO button ( ▲ ▼

Multi-Information Display

METER SETUP See page86 .

POSITION SETUP ＊ See page92 .

LIGHTING SETUP See page94 .

DOOR SETUP See page 99.

＊

All models except Canadian TSX with 4-cylinder engine

85

2010 TSXMulti-Information Display

Meter Setup Here are the four custom settings for the meter setup:

LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP A RESET with REFUEL ELAPSED TIME RESET

While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.

Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.

▲ ▼

86

: Press the SEL/RESET button. ). : Press the INFO button ( ▲ ▼

2010 TSXLanguageSelection

Multi-Information Display

There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions:

You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Press the SEL/RESET button to see the selections.

Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again.

CONTINUED

87

2010 TSXMulti-Information Display

AdjustOutsideTemp.Display

U.S. models

Canadian models

U.S. models

Canadian models

If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions:

You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to enter the setting.

▲ ▼

88

Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.

2010 TSXTripAResetWithRefuel

Multi-Information Display

To cause Trip A and average fuel for trip A to reset every time you refuel your vehicle, follow these instructions:

You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Press the SEL/RESET button to see the selections.

Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP A RESET with REFUEL’’ and repeat the procedure again.

CONTINUED

89

2010 TSXMulti-Information Display

ElapsedTimeReset There are three elapsed time reset choices you can make:

−

IGN OFF The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.

TRIP A when Trip A is reset.

−

The elapsed time is reset

TRIP B when Trip B is reset.

−

The elapsed time is reset

You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Press the SEL/RESET button to see the selections.

Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

90

2010 TSXWhen your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

Multi-Information Display

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again.

91

2010 TSXMulti-Information Display

Position Setup AllmodelsexceptCanadianTSXwith 4-cylinderengine You can customize the MEMORY POSITION LINK setting in position setup.

While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.

Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the custom setting then press the SEL/RESET button to enter your selection.

▲ ▼

92

: Press the SEL/RESET button.

: Press the INFO button (

). ▲ ▼

2010 TSXMemoryPositionLink

Multi-Information Display

If ‘‘MEMORY POSITION LINK’’ is set to ‘‘ON,’’ the driver’s seat moves to the position stored in the memory (see page driver’s door, using the remote transmitter.

) when you open the

142

You can choose this item to customize from ‘‘POSITION SETUP’’ by pressing the INFO ( / ▲ ▼

) button repeatedly.

Press the SEL/RESET button to see the selections.

Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘MEMORY POSITION LINK’’ and repeat the procedure again.

93

2010 TSXMulti-Information Display

Lighting Setup Here are the three custom settings for the lighting setup:

INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY

＊

While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.

Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.

▲ ▼

: Press the SEL/ RESET button. : Press the INFO ). button ( ▲ ▼

94

＊

: All models except Canadian TSX with 4-cylinder engine

2010 TSXInteriorLightDimmingTime

Multi-Information Display

The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions:

You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼

) button repeatedly.

Press the SEL/RESET button to see the selections.

Select the desired setting (15 SEC, 30 SEC, or 60 SEC) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.

CONTINUED

95

2010 TSXMulti-Information Display

HeadlightAutoOffTimer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the driver’s door. To change how long the lights stay on before they go off, follow these instructions:

96

You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼

) button repeatedly.

Press the SEL/RESET button to see the selections.

Select the desired setting (60 SEC, 30 SEC, 15 SEC or 0 SEC) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

2010 TSXAutoLightSensitivity AllmodelsexceptCanadianTSXwith 4-cylinderengine The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels:

−

MAX The headlights come on when it is bright.

−

HIGH The headlights come on when it is somewhat bright.

−

MID The headlights come on when it is as bright as sunset or sunrise.

−

LOW The headlights come on when it is somewhat dark.

Multi-Information Display

−

MIN The headlights come on when it is dark.

You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼

) button repeatedly.

CONTINUED

97

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘HEADLIGHT AUTO OFF TIMER’’ and repeat the procedure again.

2010 TSXMulti-Information Display

Press the SEL/RESET button to see the selections.

Select the desired setting (MAX, HIGH, MID, LOW or MIN) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again.

98

2010 TSXDoor Setup Here are the five custom settings for the door setup:

AUTO DOOR LOCK DOOR LOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER AUTO DOOR UNLOCK

While ‘‘DOOR SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.

Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.

▲ ▼

: Press the SEL/ RESET button. : Press the INFO button ( ). ▲ ▼

Multi-Information Display

CONTINUED

99

2010 TSXMulti-Information Display

AutoDoorLock There are three settings you can choose from:

−

OFF The auto door lock is deactivated all the time.

−

WITH VEH SPD The doors lock when the vehicle speed reaches about 10 mph (about 15 km/h).

−

SHIFT FROM P The doors lock whenever you move the shift lever out of Park. (Automatictransmissionmodelonly)

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

100

A/T model is shown.

Press the SEL/RESET button to enter the selecting mode.

Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

2010 TSXWhen your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

Multi-Information Display

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again.

DoorLockMode

To select whether the driver’s door unlocks or all the doors unlock when you unlock the doors with the remote transmitter or the key, follow these instructions.

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

CONTINUED

101

2010 TSXMulti-Information Display

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR LOCK MODE’’ and repeat the procedure again.

Press the SEL/RESET button to enter the selecting mode.

Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

102

2010 TSXMulti-Information Display

KeylessLockAcknowledgment When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.

). You can

292

To turn this feature on or off, follow these instructions.

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Press the SEL/RESET button to enter the selecting mode.

Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.

▲ ▼

CONTINUED

103

2010 TSXSecurityRelockTimer If you unlock the doors with the remote transmitter, but do not open any of the doors within 30 seconds, the doors and the fuel fill door, automatically relock, and the security system sets.

You can change this relock time from 30 seconds to 60 or 90 seconds.

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Multi-Information Display

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again.

104

2010 TSXPress the SEL/RESET button to enter the selecting mode.

Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.

▲ ▼

When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.

Multi-Information Display

If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again.

CONTINUED

105

2010 TSXDRIVER DOOR with IGN OFF The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position.

−

ALL DOORS with IGN OFF All the doors unlock when you turn the ignition switch to the LOCK (0) position.

−

−

OFF deactivated all the time.

The auto door unlock is

You can choose this item to customize from ‘‘DOOR SETUP’’ by pressing the INFO ( / ) button repeatedly.

▲ ▼

Multi-Information Display

AutoDoorUnlock There are five possible settings for automatic transmission models and three possible settings for manual transmission models.

Automatictransmissionmodelonly DRIVER DOOR with SHIFT to P − The driver’s door unlocks when you move the shift lever to Park.

Automatictransmissionmodelonly ALL DOORS with SHIFT to P All − the doors unlock when you move the shift lever to Park.