Download PDF Manual

information display indicating which door(s), etc is not completely closed.


Hood and liftgate


If the hood and/or liftgate is not completely closed, the Information symbol in the instrument panel will light up and a message will be dis- played, regardless of the vehicle's


speed.


02


59


02 Instruments and controls


Information display


Messages


02


When an indicator or warning light in the instru- ment panel comes on, a message is also shown in the information display. To read a message: 1. Press the READ button (1). 2. Pressing READ repeatedly enables you to scroll to any other messages that may be stored.


60


NOTE


Message


Meaning


If a message is displayed when e.g. you are using the trip computer, this message must be read before you can access the trip com- puter.


SERVICE REQUIREDA


Message


Meaning


STOP SAFELYA


HIGH ENGINE TEMP STOP SAFELY


SERVICE URGENTA


SEE MANUALA


Stop the vehicle in a safe place and switch off the engine to help prevent the risk of seri- ous damage.


Stop the vehicle in a safe place and switch off the engine to help prevent the risk of seri- ous damage.


Take your car to a trained and qualified Volvo service techni- cian for inspection immediately.


Refer to your owner's manual. For additional information, please contact your Volvo retailer.


BOOK TIME FOR SERVICE


TIME FOR REGULAR MAINTE- NANCE


MAINTE- NANCE OVER- DUE


Take your car to a trained and qualified Volvo service techni- cian for inspection as soon as possible (but preferably before the next scheduled mainte- nance service).


Book time for service at an authorized Volvo workshop.


This message is affec- ted by the number of miles/km driven, by the number of months, or by the number of engine hours since the service reminder was reset at the most recent regu- larly scheduled service.


If the vehicle is not serv- iced according to schedule, the warranty may not apply to dam- aged parts, etc.


Message


TIME FOR REGULAR MAINTE- NANCE


REMINDER CHECK OIL LEVEL


Meaning


This message is affec- ted by the number of miles/km driven, by the number of months, or by the number of engine hours since the service reminder was reset at the most recent regu- larly scheduled service.


Stop as soon as possi- ble and switch off the engine, check the oil level and top up if nec- essary, see page 206.


A This is part of the message. Additional information will also


be displayed.


02 Instruments and controls


Information display


02


61


02 Instruments and controls


12-volt sockets


12-volt socket (front seat)


NOTE


NOTE


02


The cover should be kept on when the aux- iliary socket is not in use.


The 12-volt socket in the rear seat cannot function as a cigarette lighter.


Auxiliary equipment The buttons to the left of the 12-volt socket can be used for Volvo-installed optional or auxiliary equipment.


12-volt socket (rear seat)


12-volt socket, auxiliary equipment The 12-volt socket can be used to plug in cer- tain accessories such as cellular telephones, etc. The maximum current is 10 A. The key must be in position I (or higher) for the auxiliary socket to function.


Ashtrays/cigarette lighter The auxiliary socket can also be used for a cig- arette lighter1, and ashtrays, which can be pur- chased from your Volvo retailer.


1 Accessory.


62


02 Instruments and controls


Pos.


Lighting


All lighting off. Low beam head- lights (daytime running lights) will automatically come on if the ignition key is in position II. Front and rear parking lights and license plate lights will also be on. High beams can be briefly flashed. The headlights switch off automatically when the ignition key is removed.


Parking lights


Daytime running lights. High beams and high beam flash can be used in this position.


Parking lights The front and rear parking lights can be turned on even when the ignition is switched off. (cid:177) Turn switch (1) to the parking light position. The license plate lights also illuminate when the parking lights are switched on.


1 On Canadian models, the daytime running lights will remain on with the light switch in this position.


Lighting panel


Headlights 1. Turn the ignition key to position II. 2. The low beam headlights (daytime running


lights) illuminate automatically, except when the light switch (1) is in the parking light position1.


02


NOTE


See page 65 for information on switching between high and low beams.


Brake lights The brake lights come on automatically when the brakes are applied.


Fog lights


Front fog lights (option) The front fog lights can be used in combination with either the headlights or the parking lights. 1. Turn the ignition key to position II. 2. Press button (3) to turn on the front fog


lights.


An indicator light in the button illuminates when the front fog lights are on.


(cid:96)(cid:96)


63


02 Instruments and controls


Lighting panel


Rear fog light The single rear fog light is located in the driver's side taillight cluster. The rear fog light will only function in combi- nation with the high/low beam headlights or the optional front fog lights. 1. Turn the ignition key to position II. 2. Press button (5) to turn on the rear fog light. An indicator light in the button illuminates when the rear fog light is on.


NOTE


The rear fog light is considerably brighter than the normal taillights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters).


NOTE


To make it easier to read the odometer, trip odometer, clock, and ambient temperature, these gauges illuminate when the vehicle is unlocked and when the key has been removed from the ignition switch. The light- ing will go out when the vehicle is locked.


Move the thumb wheel (2) up to increase brightness or down to decrease brightness.


Unlocking the fuel filler door With the ignition switched off, press button (4) to unlock the fuel filler door. Please note that the fuel filler door will remain unlocked until the car begins to move forward. An audible click will be heard when the fuel filler door re-locks.


Instrument panel lighting The instrument panel lighting illuminates when the ignition is in position II and the light switch (1) is in either position


or


02


64


Lever positions


Turn signals


High/low beam headlights


02 Instruments and controls


Left-side steering wheel lever


When turning (cid:177) Move the lever as far up or down as pos- sible (to position 2) to start the turn signals. The turn signals will be cancelled automatically by the movement of the steering wheel, or the lever can be returned to its initial position by hand.


When changing lanes The driver can automatically flash the turn sig- nals 3 times by: • Moving the turn signal lever up or down to


position 1 and releasing it.


• Moving the lever up or down to position 2
and immediately back to its original posi- tion.


NOTE


• This automatic flashing sequence can be interrupted by immediately moving the lever in the opposite direction.


• If the turn signal indicator flashes faster


than normal, check for a burned-out turn signal bulb.


Continuous high beams 1. Turn the ignition key to position II. 2. With the light switch (1) in position


see page 63, pull the turn signal lever toward the steering wheel (position 4) to toggle between high and low beams.


High beam flash 1. Turn the ignition key to position II. 2. Pull the turn signal lever to position 3. The high beams will remain on until the lever is released.


Home safe lighting When you leave your car at night, you can make use of the home safe lighting function to illuminate the area in front of the car. 1. Remove the key from the ignition switch. 2. Pull the direction indicator lever as far as


possible towards the steering wheel (to position 4) and release it.


3. Exit the car and lock the doors. The headlights and parking lights will illuminate and remain on for 301, 60 or 90 seconds. The time interval can be changed according to your


02


(cid:96)(cid:96)


65


Turn signals, lane change position


Turn signals, position for normal turns


High beam flash


Toggle between high and low beams, Home Safe lighting


1 Factory setting


02 Instruments and controls


Left-side steering wheel lever


preferences by using the Personal Settings function, see page 82 for more information.


02


66


02 Instruments and controls


• ACTUAL SPEED (current speed in mph,


Canadian models only)


• DSTC, see page 151


NOTE


Warning messages from the car's monitor- ing systems will override the trip computer function.


If a warning message is shown in the informa- tion display while you are using the trip com- puter: 1. Acknowledge the message by pressing the


READ (button 1).


2. Press READ again to return to the trip


computer function.


Controls The trip computer functions can be accessed by twisting the thumb wheel (2) one step at a time in either direction. Twisting a final time returns you to the original function.


Resetting AVERAGE (average fuel consumption) and AVERAGE SPEED can be reset. 1. Select one of these functions. 2. Press RESET (3).


Trip computer


MILES TO EMPTY TANK This function shows the approximate distance that can be driven on the fuel remaining in the tank. The calculation is based on average fuel consumption during the last 20 miles (30 km) of driving and the amount of fuel remaining in the tank when the reading was taken. When the message ---- miles to empty tank appears in the display, refuel as soon as pos- sible. AVERAGE This value indicates fuel consumption since the last time the trip computer was reset, by press- ing RESET (button 3). When the engine is switched off, information on fuel consumption is stored and remains in system memory until RESET (button 3) is pressed again.


INSTANTANEOUS This value indicates the current fuel consump- tion, based on readings taken once per sec- ond. When the car is not moving, "----" will be displayed. AVERAGE SPEED This value indicates average speed since the last time the trip computer was reset, by press- ing RESET (button 3). When the engine is switched off, information on average speed is stored and remains in system memory until the RESET (button 3) is pressed again.


02


(cid:96)(cid:96)


67


READ (press to acknowledge/confirm/ erase a message) Thumb wheel (used to scroll among the trip computer menus) RESET


The trip computer stores information gathered from several systems in your car and has four menus (five on Canadian models) that can be shown in the information display. • MILES TO EMPTY TANK • AVERAGE (average fuel consumption) • INSTANTANEOUS (current fuel con-


sumption)


• AVERAGE SPEED


02 Instruments and controls


Trip computer


02


ACTUAL SPEED (Canadian models only) This function provides the driver with an instan- taneous conversion of the car's current speed from km/h to mph.


NOTE


Trip computer readings may vary slightly depending on the circumference of the tires on the car, tire inflation, or driving style.


68


Engaging the cruise control function


Increasing or decreasing speed


NOTE


02 Instruments and controls


Cruise control (option)


02


• Cruise control will not function at speeds below 20 mph (30 km/h).


• Momentary acceleration, for less than 1 minute (e.g. when passing another car), does not affect cruise control oper- ation. The car will automatically return to the previously set speed when the accelerator pedal is released.


The cruise control buttons are located on the left side of the steering wheel hub.


NOTE


This does not set the vehicle's speed.


1. Press the CRUISE button. CRUISE will


appear in the function display in the center of the instrument panel.


2. Press + or – to set the current speed.


CRUISE ON will be displayed.


Use + or – in the following ways to increase or decrease the vehicle's speed: 1. Press and hold down + or – until the vehicle


reaches the desired speed. This will become the set speed when the button is released.


2. Press + or – for approximately a half sec- ond and release the button to increase or decrease vehicle speed by approximately 1 mph (1.6 km/h).


Temporarily disengaging the cruise control • Press 0 to temporarily disengage cruise


control.


CRUISE will appear in the function display. The currently set speed is stored in the sys- tem's memory.


Cruise control is also automatically disengaged: • If the speed drops below approximately


20 mph (30 km/h) when driving uphill.


• When the brake or clutch pedal is


depressed.


• If the gear selector is moved to posi-


tion N.


(cid:96)(cid:96)


69


02 Instruments and controls


Cruise control (option)


02


• During wheel spin or wheel lock-up. • If the vehicle's speed is increased by using


the accelerator pedal for more than 1
minute.


Returning to the set speed


Press the button to resume the previously set speed. CRUISE ON will be displayed.


Disengaging cruise control Cruise control can also be disengaged by: • Pressing the CRUISE button (CRUISE


ON will no longer be shown in the function display).


• Putting the gear selector in Neutral (N).


WARNING


Cruise control should not be used in heavy traffic or when driving on wet or slippery roads. Cruise control may not maintain set speed on steep downgrades.


70


02 Instruments and controls


Windshield wipers


Manual wiper function


Windshield/headlight washers


Rain sensor (option) – on/of, see page 71


Thumb wheel


Liftgate wiper/washer


Windshield wipers off


The windshield wipers are off when the lever is in position 0.


From position 0, move the lever upward. The windshield wipers will sweep one stroke at a time for as long as the lever is held up.


Intermittent wiper function


With the lever in this position, you can set the wiper interval by mov- ing the thumb wheel (C) upward to increase wiper speed or down- ward to decrease the speed.


Continuous wiper function


The wipers operate at "normal" speed. High speed wiper function.


A–Windshield washers Pull the lever toward the steering wheel and release it. The wipers will make 2–3 sweeps across the windshield after the lever has been released.


Right-side steering wheel lever


CAUTION


• Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers are in operation.


• Before using the wipers, ice and snow


should be removed from the wind- shield/rear window. Be sure the wiper blades are not frozen in place.


02


Headlight washers (certain models) When the lever has been pulled, high pressure jets mounted in the bumper will spray the head- lights. The following applies to conserve washer fluid, see page 63 for information on the light switch positions:


Low/high beam headlights on The headlights will be washed the first time the windshield is washed. Thereafter, the head- lights will only be washed once for every five times the windshield is washed within a 10- minute period.


Parking lights on Optional Bi-Xenon(cid:159) headlights will be washed once for every five times the windshield is washed. Normal halogen headlights will not be washed.


(cid:96)(cid:96)


71


02 Instruments and controls


Right-side steering wheel lever


B – Rain sensor (option)


02


The rain sensor regulates windshield wiper speed according to the amount of water on the windshield. The sensitivity of the rain sensor is adjusted by moving the thumb wheel (C in the illustration on the previous page) up (the wipers will sweep the windshield more frequently) or down (the wipers will sweep the windshield less frequently).


On/Off Activating the rain sensor 1. Switch on the ignition. 2. Put the windshield wiper lever in position


0.


72


3. Press button B (see page 71). The rain sen- sor symbol will appear in the lower display.


Manual deactivation The rain sensor can be deactivated by: • Pressing button (B). or • Moving the windshield wiper lever down.


NOTE


The rain sensor function will remain acti- vated if the lever is briefly moved up to activate the "manual sweep" function.


CAUTION


The rain sensor should be deactivated when washing the car in an automatic car wash, etc. If the rain sensor function is left on, the wipers will start inadvertently in the car wash and could be damaged.


Automatic deactivation The rain sensor is deactivated automatically in the following situations: • When the key is removed from the ignition. • Five minutes after the ignition is switched


off if the key is left in the ignition.


C – Thumb wheel The thumb wheel is used to set the wiper inter- val when intermittent wiping is selected, or the sensitivity to the amount of rain on the wind- shield when the rain sensor is selected. Move the wheel upward or downward to increase/ decrease wiper speed when the intermittent function is selected, or to increase/decrease the optional rain sensor's sensitivity when the this function is activated.


D – Liftgate wiper/washer Press the lever forward to wipe and wash the liftgate window. The wiper will sweep the win- dow several times after the lever has been released. The button at the end of the lever has three positions: • Intermittent wiping: Press in the upper sec-


tion of the button.


• Normal wiper speed: Press in the lower


section of the button.


• Neutral position: The wiper function is


switched off.


02 Instruments and controls


Right-side steering wheel lever


Liftgate wiper and reverse gear • If the front wipers are on and the transmis-


sion is put into reverse gear, the liftgate wiper will be activated.


• If the transmission is in reverse and the


manual windshield wiper function is used (the lever is pushed upward), the liftgate wiper will also be activated for as long the lever is held up.


• If the liftgate wiper is already in normal wip- ing function, the normal wiping function will continue.


02


73


02 Instruments and controls


Steering wheel adjustment, Hazard warning flashers


Steering wheel adjustment


02


Check that the steering wheel is locked in the new position.


WARNING


Never adjust the steering wheel while driv- ing.


Hazard warning flashers


NOTE


• Regulations regarding the use of the


hazard warning flasher may vary, depending on where you live.


• The hazard warning flashers will be acti-


vated automatically if an airbag deploys.


Both the height and the reach of the steering wheel can be adjusted to a comfortable posi- tion for the driver. 1. Pull down the lever on the steering column


to release the steering wheel.


2. Adjust the steering wheel to a suitable


position


3. Press the lever back into place to lock the steering wheel in the new position. If nec- essary, press the steering wheel slightly while pressing the lever into the locked position.


The four-way flasher should be used to indi- cate that the vehicle has become a traffic haz- ard. To activate the flashers, press the triangu- lar button in the center dash. Press the button again to turn off the flashers.


74


02 Instruments and controls


Parking brake (hand brake)


The parking brake lever is located between the front seats.


NOTE


4.


If the vehicle rolls, the parking brake lever must be pulled more firmly.


5. When parking a vehicle always put the gear selector in first gear (for manual transmis- sion) or P (for automatic transmission).


Parking on a hill • If the vehicle is pointing uphill, turn the front


wheels so that they point away from the curb.


• If the vehicle is pointing downhill, turn the front wheels so that they point toward the curb.


Releasing the parking brake 1. Press firmly on the brake pedal. 2. Pull the lever up slightly, press the button at the end of the lever and lower the lever completely.


The indicator light will illuminate even if the parking brake has only been partially applied.


WARNING


Pull up the parking brake lever up firmly to its full extent.


When applying the parking brake 1. Press firmly on the brake pedal. 2. Pull the parking brake lever up firmly to its


full extent.


3. Release the brake pedal and ensure that


the vehicle is at a standstill.


Parking brake


02


75


02 Instruments and controls


Power windows


Operation


02


Control panel in driver's door Power window controls


The power windows are controlled by buttons in the arm rests. • The ignition must be ON (ignition key in


position I, II or the engine running) for the power windows to function.


• The power windows will also function after the ignition has been switched off as long as neither of the front doors has been opened.


76


Opening a window Lightly press down the front edge of either of the buttons (A) to the first detent ("stop") to open a window to the position of your choice.


WARNING


• Always remove the ignition key when


the vehicle is unattended.


• Never leave children unattended in the


vehicle.


• Make sure that the windows are com- pletely unobstructed before they are operated.


• Press the front part of any of the buttons (A) as far down as possible and release to automatically open the window com- pletely.


• To stop the window at any time, pull the


button up.


Closing a window • Lightly pull up the front edge of any of the


buttons (A) to the first detent ("stop") to close a window to the position of your choice.


• Pull the front part of any of the buttons (A) up as far as possible and release to auto- matically close the window completely. To stop the window at any time, press the but- ton down.


Power window control – front passenger's side


The control for the power window in the front passenger's door operates that window only.


Rearview mirror


Rearview mirror with compass (option)


Calibrating the compass


Mirrors


02


02 Instruments and controls


Day/night control


Normal position


Night position, reduces glare from follow- ing traffic


Night position To reduce glare from the headlights of follow- ing vehicles, use control (1) to switch between the normal and night-driving positions.


Auto-dim function (option) An optional integrated sensor reacts to head- lights from following traffic and automatically reduces glare.


The upper right-hand corner of the rearview mirror has an integrated display that shows the compass direction toward which the car is pointing. Eight different directions can be dis- played: N, NE, E, SE, S, SW, W and NW. The display shows your car's orientation with respect to true north.


The earth is divided into 15 magnetic zones. The compass is initially set for the zone to which the car was delivered, and should always be adjusted if the car is driven to a new magnetic zone. A "C" will be displayed if cali- bration becomes necessary. To calibrate the compass: 1. Stop the car in a large, open area, away


from traffic.


2. Using a pen or similar object, hold the but-


ton (1) depressed for at least 6 seconds. "C" will be displayed.


(cid:96)(cid:96)


77


02 Instruments and controls


Mirrors


02


Power door mirrors


Magnetic zones 3. Press button (1) for at least 3 seconds to


display the number of the current magnetic zone.


4. Press button (1) repeatedly until the num-


ber for the required geographical area (1 – 15) is displayed. "C" will be displayed again.


5. Drive slowly in a circle at a maximum speed of 6 mph (10 km/h) until a compass direc- tion is displayed.


Calibration is complete.


The mirror control switches are located on the driver's door armrest.


Adjusting the mirrors


WARNING


• The mirrors should always be adjusted


prior to driving.


• Objects seen in the passenger's side wide-angle door mirror are closer than they appear to be.


78


Driver's door mirror: (cid:177) Press the L button (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the driver's door mirror.


Passenger's door mirror: 1. Press the R switch (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the passenger's door mirror.


2. After you have adjusted the mirror(s), press the L or R switch again (the LED will go out) to deactivate the adjustment control.


Storing the mirrors' position The position of the door mirrors is stored when the vehicle is locked. The next time the driver's door is unlocked with the same remote control and that door is opened within 2 minutes, the optional power driver's seat and side door mir- rors will automatically move to the position that they were in when the doors were most recently locked with the same remote control.


Folding power door mirrors (option on certain markets only) The mirrors can be folded in for parking/driving in narrow spaces.


02 Instruments and controls


Folding the mirrors in 1. Press down the L and R mirror control but- tons on the driver's door at the same time. 2. Release them after approximately one sec- ond. The mirrors automatically fold in to the fully retracted position. Folding the mirrors out Fold out the mirrors by pressing down the L and R buttons at the same time. The mirrors automatically fold out to the fully extended position. Automatic folding When the vehicle is locked/unlocked with the remote control or with the optional keyless drive system (see page 123), the power door mirrors with automatically fold in or out.


NOTE


The door mirrors will not fold out automati- cally when the vehicle is unlocked if they were folded in using the buttons on the driv- er's door control panel.


This function can be activated/deactivated in Personal settings (see page 82). In the menu system, go to Car settings locking.


Fold mirr. when


Return to "neutral" position If a mirror has been inadvertently moved (bum- ped in a parking lot, etc.) from its original (neu- tral) position, it must be moved back to this position before automatic folding will function again. To so so: 1. Fold in the mirrors by pressing the L and


R mirror control buttons on the driver's door at the same time.


2. Fold them out again by pressing the L and


R mirror control buttons.


This returns the mirrors to their original (neutral) positions.


Blind Spot Information System (BLIS) - option The Blind Spot Information System (BLIS) is an information system that indicates the presence of another vehicle in the side-view mirror's "blind area." See page 157 for detailed infor- mation.


Mirrors


02


79


02 Instruments and controls


Power moonroof (option)


Operating the moonroof


02


Moonroof control in the ceiling console


To operate the moonroof, the ignition key must first be turned to the intermediate or drive posi- tion (position I, II or the engine running). The moonroof can be opened in two ways:


Tilt position


Sliding moonroof


Auto open


Manual open


Manual close


Auto close


Tilt open


Tilt close


Tilt position Open: Press the rear edge of the control upward to position 5. Close: Pull the rear edge of the control down to position 6.


80


Sliding moonroof Auto open/close Open: Pull the switch as far back as possible (to position 1) and release it to automatically slide open the moonroof. Close: Push the switch as far forward as pos- sible (to position 4) and release it to automati- cally close the moonroof. Manual open/close Open: Pull the switch back to the first stop (position 2) and hold it until the moonroof has opened to the position of your choice. Close: Push the switch forward to the first stop (position 3) and hold it until the moonroof has closed to the position of your choice, or has closed completely.


NOTE


If the moonroof is repeatedly obstructed during auto-close operation, an overload circuit breaker will temporarily halt moon- roof function. The moonroof will return to normal function after a brief cool-down period.


02 Instruments and controls


Power moonroof (option)


Visor


The optional moonroof features a sliding visor. The visor slides open automatically when the moonroof is opened, and must be closed man- ually.


CAUTION


• Remove ice and snow before opening


the moonroof.


• Do not operate the moonroof if it is fro-


zen closed.


• Never place heavy objects on the


moonroof.


WARNING


• If the moonroof is obstructed during auto-close operation, it will automati- cally reverse direction and return to its starting position.


• During manual closing, if the moonroof


is obstructed, immediately open it again.


WARNING


• Never open or close the moonroof if it is


obstructed in any way.


• Never allow a child to operate the


moonroof.


• Never extend any object or body part though the open moonroof, even if the vehicle's ignition is completely switched off.


• Never leave a child alone in a vehicle.


02


81


02 Instruments and controls


Personal settings


Control panel


02


Display


Menu button


Exit button


Enter button


Menu navigation controls


82


Personal settings can be made for some of the car's functions, such as the central locking system, climate control, and the audio system. Please refer to page 231 for more information on the audio functions that can be adjusted. The settings are presented in the display (A).


To access the menu and adjust settings 1. Press MENU (B). 2. Scroll to Car Settings using the menu nav-


igation control (E). 3. Press ENTER (D). 4. Select an alternative using the menu navi-


gation control (E).


5. Confirm your selection by pressing


ENTER.


To exit the menu Press EXIT (C).


Available settings


Clock adjust To set the time: 1. Use the number keys or the up/down arrow


keys on the navigation control (E) to change the hour or minute.


2. Select hour(s) or minute(s) to be changed


with the left/right arrow keys.


3. Press ENTER to start the clock.


NOTE


If you are currently using the 12-hour time setting, use the up/down arrow keys to select AM/PM after the minute-setting has been adjusted.


Lock confirmation light When the car is locked/unlocked with the remote control, the direction indicators can be selected to flash to confirm the action. The alternatives On/Off are available for both lock- ing and unlocking.


Autolock When the car starts to move, the doors and liftgate can be locked automatically. The alter- natives On/Off are available.


NOTE


Pulling the handle twice on a door unlocks and opens that door.


Unlock There are two alternatives for unlocking:


02 Instruments and controls


• Global (All doors) – unlocks all doors and the liftgate with one press on the remote control.


• Two Step (Two-stage unlocking) – This alternative unlocks the driver's door with one press on the remote control. A second press unlocks the passenger's door and the liftgate.


Automatically folding the door mirrors The setting makes it possible to automatically fold the door mirrors in or out when the vehicle is locked or unlocked. See page 78.


Operating side windows The following alternative can be selected for opening the door windows at the same time by pressing and holding the Unlock switch in either of the front doors (see page 127 for additional information) 1


NOTE


The ignition key must be in position I or higher (see page 141) before the door win- dows can be opened using the switches in the doors.


• Auto open all windows On/Off


Temporarily turning off the alarm sensor(s) The alarm sensors can be temporarily turned off (if, for example, a person or a pet remains in the vehicle when the doors are locked from outside with the remote control). There are two alternatives:Activate once and Ask on exit, see page 118 and 129 .


Approach lighting This alternative determines the length of time for which the car's lights will remain on when the Approach light button on the central lock- ing system's remote control is pressed. Inter- vals of 30/60/90 seconds may be selected, see teh section "Remote control functions" for more information.


Home safe lighting This alternative determines the length of time for which the car's lights will remain on when the high beam lever on the steering column is pulled toward the wheel with the ignition switched off. Intervals of 30/60/90 seconds may be selected, see page 65 for information on using this function.


Personal settings


Information • VIN number – The VIN (Vehicle Identifica- tion Number) is the car's unique identity number.


• Number of Keys – the number of keys reg-


istered for the car is displayed here.


Climate functions • Blower speed in AUTO mode – the blower speed can be set to AUTO mode in models equipped with ECC. Choose between "Low", "Normal" and "High".


• Timer for recirculation – when the timer is active, the air recirculates in the car for 3– 12 minutes depending on the ambient tem- perature. Select On/Off depending on whether the recirculation timer is to be active or not.


Keyless locking and unlocking (option as available) The following alternatives can be selected for locking and unlocking the doors and liftgate: • All doors – all doors are locked or unlocked


at the same time.


• Doors on the same side – front and rear


doors on the same side are unlocked together.


1 This menu alternative also makes it possible to open both door windows by pressing and holding the Unlock button on the remote control for several seconds.


02


(cid:96)(cid:96)


83


02 Instruments and controls


Personal settings


02


• Both front doors – both front doors are


unlocked together.


• One front door – either of the front doors


can be unlocked separately2.


Reset to factory settings Use this alternative to return to the default cli- mate system settings.


2 Factory default.


84


Introduction


The HomeLink Wireless Control System pro- vides a convenient way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as gate opera- tors, garage door openers, entry door locks, security systems, even home lighting. Addi- tional HomeLink information can be found on the Internet at www.homelink.com.


02 Instruments and controls


HomeLink® Wireless Control System (option)


WARNING


• If you use HomeLink to open a garage door or gate, be sure no one is near the gate or door while it is in motion.


• When programming a garage door


opener, it is advised to park outside of the garage.


• Do not use HomeLink with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manu- factured before April 1, 1982). A garage door that cannot detect an object - sig- naling the door to stop and reverse - does not meet current U.S. federal safety standards. For more information, contact HomeLink at: www.homelink.com.


Retain the original transmitter of the RF device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. Refer to “Erasing HomeLink Buttons”.


Programming HomeLink


NOTE


02


Some vehicles may require the ignition switch to be turned on or to the second (“accessories”) position for programming and/or operation of HomeLink. It is also rec- ommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal.


1. Position the end of your hand-held trans- mitter 1–3 inches (5–14 cm) away from the HomeLink button you wish to program while keeping the indicator light in view. 2. Simultaneously press and hold both the


chosen HomeLink and hand-held transmit- ter buttons until the HomeLink indicator light changes from a slow to a rapidly blink- ing light. Now you may release both the HomeLink and hand-held transmitter but- tons.


(cid:96)(cid:96)


85


02 Instruments and controls


HomeLink® Wireless Control System (option)


02


NOTE


Some devices may require you to replace this Programming Step 2 with procedures noted in the “Gate Operator / Canadian Pro- gramming” section. If the HomeLink indica- tor light does not change to a rapidly blinking light after performing these steps, contact HomeLink at www.homelink.com.


3. Firmly press, hold for five seconds and release the programmed HomeLink but- ton up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink button and observe the indicator light. • If the indicator light stays on con- stantly, programming is complete and your device should activate when the HomeLink button is pressed and released.


• If the indicator light blinks rapidly for


two seconds and then turns to a con- stant light continue with “Program- ming” steps 4-6 to complete the pro- gramming of a rolling code equipped device (most commonly a garage door opener).


4. At the garage door opener receiver (motor- head unit) in the garage, locate the “learn” or “smart” button. This can usually be


found where the hanging antenna wire is attached to the motor-head unit.


5. Firmly press and release the “learn” or


“smart” button. (The name and color of the button may vary by manufacturer.) There are 30 seconds to initiate step 6.


6. Return to the vehicle and firmly press, hold


for two seconds and release the pro- grammed HomeLink button. Repeat the “press/hold/release” sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.


HomeLink should now activate your rolling code equipped device.


Gate Operator/Canadian Programming Canadian radio-frequency laws require trans- mitter signals to “time-out” (or quit) after sev- eral seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. If you live in Canada or you are having difficul- ties programming a gate operator or garage door opener by using the “Programming” pro-


86


cedures, replace “Programming HomeLink” step 2 with the following: • Continue to press and hold the HomeLink


button while you press and release - every two seconds (“cycle”) your hand- held transmitter until the HomeLink indica- tor light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink and hand-held transmitter buttons.


Proceed with “Programming” step 3 to com- plete.


Using HomeLink To operate, simply press and release the pro- grammed HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficul- ties or questions, contact HomeLink at: www.homelink.com.


02 Instruments and controls


HomeLink® Wireless Control System (option)


This device complies with FCC rules part 15
and Industry Canada (IC) RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) This device must accept any interference that may be received including interference that may cause undesired opera- tion.


NOTE


The transmitter has been tested and com- plies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.1


HomeLink and the HomeLink house are regis- tered trademarks of Johnson Controls, Inc.


Erasing HomeLink Buttons To erase programming from the three Home- Link buttons (individual buttons cannot be erased but can be “reprogrammed” as outlined below), follow the step noted: • Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 10 seconds. Release both but- tons. Do not hold for longer that 20 sec- onds. HomeLink is now in the train (or learning) mode and can be programmed at any time beginning with “Programming” - step 1.


Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink but-


ton. DO NOT release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the Home- Link button, proceed with “Programming” - step 1.


For questions or comments, contact HomeLink at: www.homelink.com or 1–800–355–3515.


1 The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.


02


87


General information................................................................................. 90
Air vents.................................................................................................. 92
Manual climate control............................................................................ 93
Electronic Climate Control (ECC) – option.............................................. 96
Air distribution......................................................................................... 99


88


CLIMATE


03


03 Climate


General information


Air conditioning – A/C Your car is equipped with a climate control system that includes either manually adjusta- ble air conditioning or optional Electronic Cli- mate Control (ECC). The air conditioning system can be switched off, but for optimal air quality in the passenger compartment and to prevent the windows from fogging, the air conditioning should be left on – even in cool weather.


NOTE


In warm weather, a small amount of water may accumulate under the car when it has been parked. This water is condensation from the A/C system and is normal.


Ice and snow Always keep the air intake grille at the base of the windshield free of snow.


Fog on the inside of the windows The defroster function should be used to remove fog or mist from the inside of the win- dows. Keeping the windows clean with a com- mercially available window washing spray will also help prevent fogging or misting


Climate control maintenance Special tools and equipment are required to maintain and carry out repairs on the climate system. Work of this type should only be done by a trained and qualified Volvo service tech- nician.


Refrigerant Volvo cares about the environment. The air conditioning system in your car contains a CFC-free refrigerant – R134a. This substance will not deplete the ozone layer. The system contains 1.2 lbs (530 g) R134a (HFC 134a), and uses PAG oil.


Passenger compartment filter Replace the cabin air filter with a new one at the recommended intervals. Please refer to your Warranty and Service Records Informa- tion booklet, or consult a trained and qualified Volvo service technician for these intervals. The filter should be replaced more often when driving under dirty and dusty conditions. The filter cannot be cleaned and therefore should always be replaced with a new one.


NOTE


There are different types of cabin air filters. Ensure that the correct type is installed.


Display The display above the climate control panel shows the climate settings that have been made.


Personal settings There are two functions in the climate system that can be set to your preferences: • Blower speed to Auto mode (models with


ECC only).


• Timer controlled recirculation of the air in


the passenger compartment.


03


90


03 Climate


General information


closed. If you drive with the windows or moon- roof open, it may be preferable to manually adjust the temperature and blower control (the LED in the AUTO switch should be off).


Acceleration The air conditioning system is temporarily switched off during full throttle acceleration.


For information about how to make these set- tings, see the Personal settings section on page 82.


Models equipped with ECC (option)


Sensors • The sunlight sensor is on the upper side of


the dashboard


• The passenger compartment temperature sensor is located behind the climate sys- tem control panel.


• The ambient temperature sensor is in the


driver's side door mirror.


• The humidity sensor is in the rearview mir-


ror.


These sensors should never be obstructed.


NOTE


The sunlight sensor monitors the side of the vehicle from which the sun shines into the passenger compartment. This means that the temperature may differ slightly between the left and right air vents, even if the climate system temperature is set to be the same for both sides of the passenger compart- ment.


Side windows and optional moonroof The electronic climate control system will func- tion best if the windows and moonroof are


03


91


03 Climate


Air vents


Air vents in the dashboard


Open


Closed


Horizontal air flow


Vertical air flow


Direct the outer air vents toward the side win- dows to defrost.


03


92


Climate system control panel


Blower speed


Recirculation


Defroster


Airflow controls


A/C – ON/OFF


Heated driver's seat


Heated front passenger's seat


Rear window and door mirror defrosters


Temperature selector


Manual climate system functions


1. Blower


The blower speed can be increased or decreased by turning the knob. If the knob is turned counterclockwise and the indicator light in the dis- play goes out, the blower and the air conditioning are


switched off. The display shows the blower symbol and OFF.


03 Climate


Manual climate control


2. Recirculation


This function can be used to shut out exhaust fumes, smoke, etc from the passen- ger compartment. The air in the passenger compartment is then recirculated, i.e. no air from outside the car is taken


into the car when this function is activated. Recirculation (together with the air condition- ing system) cools the passenger compartment more quickly in very warm weather. If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows, especially in winter.


03


(cid:96)(cid:96)


93


03 Climate


Manual climate control


Timer The timer function minimizes the risk of mist- ing, or stale air when the recirculation function is selected, see page 82 for information on set- ting the recirculation timer. Recirculation is always disengaged when you select Defroster (3).


03


3. Defroster


Directs airflow to the wind- shield and side windows and increases blower speed.


When the defroster is activated: • Air flows to the windows at high blower


speed.


• The LED in the defroster button lights up when this function is activated. The air con- ditioning system is controlled to provide maximum air dehumidification.


• The air conditioning is automatically


switched on (can be switched off by press- ing button 5).


94


4. Airflow controls


Press one of the three buttons in the illustration to activate the selected airflow. A symbol in the display above the cli- mate control panel and a lit LED in the selected button indicate that the manual func- tion has been selected. With manually selected airflow both warm and cool air can be selected. The desired temperature is selected using con- trol 9.


5. A/C – On or Off


ON: The air conditioning sys- tem is engaged when the ON light is lit. OFF: The system is disen- gaged when the OFF lights up.


Reduced heating: Press the button a second time – one LED lights up. Seat heating off: Press the button a third time – no LEDs are lit.


8. Heated rear window and door mirrors Press to defrost the rear win- dow and door mirrors. The rear window and door mirrors are defrosted simulta- neously if the switch is pressed once. The defrost


function is active if the LED in the switch is illu- minated. • The function can be switched off manually


by pressing the button,


• The defrost function switches off automat- ically after 12–20 minutes, depending on the outside temperature.


If Defroster (3) is activated the air conditioning is always engaged.


NOTE


6/7. Heated front seats (option)


Maximum heating: Press the button once – both LEDs light up.


On certain markets, the defrost function may remain on longer than 20 minutes in cold weather to help keep the rear window free from ice or condensation.


9. Temperature selector


The knob with the thermome- ter symbol is used to select cooling or heating for both the driver's and passenger's sides of the car.


03 Climate


Manual climate control


03


95


03 Climate


Electronic Climate Control (ECC) – option


03


96


Auto – On/Off


Blower speed


Recirculation


Defroster


Airflow controls


A/C – ON/OFF


Heated driver's seat


Heated front passenger's seat


Rear window and door mirror defrosters


Temperature selector


ECC functions


1. Auto – On/Off


The AUTO function automat- ically regulates climate con- trol to maintain the desired temperature. The automatic function controls heating, air conditioning, blower speed, recirculation, and air distribu-


tion. If you select one or more manual functions, the remaining functions continue to be controlled automatically. All manual settings are switched off when AUTO is switched on. AUTO CLIMATE is shown in the display.


2. Blower speed


The blower speed can be increased or decreased by turning the knob. The blower speed is regulated automati- cally if AUTO is selected. The previously set blower speed is disconnected.


NOTE


If the knob is turned counterclockwise and the blower indication in the display goes out, the blower and the air conditioning are switched off. The display shows the blower

Loading...
x