2009 Volvo C30 Owners Manual

Download PDF Manual
Power windows Door mirror button, driver's side Door mirror adjustment control Door mirror button, passenger's side 52 Instrument panel 02 02 Instruments and controls Instrument panel 10 11 12 13 14 Speedometer Turn signal, left Warning symbol – See the following pages for additional information. Information display – The display presents information and warning messages, the ambient temperature, clock, etc. When the ambient temperature is between 23 °F and 36 °F (–5 °C and +2 °C), a snowflake sym- bol is shown in the display. This symbol serves as a warning for possible slippery road surfaces. Please note that this symbol does not indicate a fault with your car. At low speeds, or when the car is not moving, the temperature readings may be slightly higher than the actual ambient tempera- ture. Information symbol – See the following pages for additional information. Turn signal, right Tachometer – Shows engine speed in thousands of revolutions per minute (rpm). Do not drive continuously with the needle in the red area of the dial, which indicates maximum allowable engine rpm range. Instead, shift to a higher gear or slow the vehicle down. The engine management system will automatically prevent exces- sively high engines speeds. This will be noticeable as a pronounced unevenness in engine speed. Indicator and warning symbols Fuel gauge, see page 257 for fuel tank vol- ume. When a warning light in the gauge comes on, the vehicle should be refueled as soon as possible. see page 67 for more information on fuel level and con- sumption in the "Trip computer” section. High beam indicator Function display – This window displays information on functions such as the (cid:96)(cid:96) 53 02 Instruments and controls Instrument panel odometer, trip odometers, optional rain sensor, and cruise control. Trip odometer reset button – The trip odometers are used to measure short dis- tances. Press the button briefly to switch between the odometer for the car's total mileage and the two trip odometers, T1 and T2. A long press (more than 2 seconds) resets the currently selected trip odometer. Temperature gauge – The gauge indicates the temperature of the engine cooling sys- tem. If the temperature is abnormally high and the needle enters the red zone, a mes- sage is shown in the display. Bear in mind that auxiliary lamps in front of the air intake reduce the cooling capacity at high outside temperatures and high engine loads. Indicator and warning symbols 02 54 02 Instruments and controls Function check The indicator and warning symbols1 light up when you turn the ignition key or the optional keyless drive start control to the driving posi- tion (position II) before starting. This shows that the symbols are functioning. Symbols in the center of the instrument panel CHECK ENGINE When the engine starts, all sym- bols go out. If the engine is not started within 5 seconds, all of the symbols except the malfunction indicator light (CHECK ENGINE) and the oil pressure warning light will go out. Certain symbols may not have their functions illustrated, depending on the car's equipment. The PARK BRAKE symbol will not go out until the parking brake has been released. Warning symbol The red warning symbol lights up to indicate a fault that could affect the car's drivability.This symbol illuminates when the vehicle is traveling at speeds above 5 mph (7 km/h). A text explaining the nature of the fault will also be shown in the information display. The symbol and accompanying text will remain on until the fault has been corrected. This sym- bol may also light up in combination with other indicator or warning symbols. Indicator and warning symbols If the red warning symbol lights up: 1. Stop the car as soon as possible in a suit- able location. 02 2. Read the message in the information dis- play. 3. Follow the instructions provided, or con- tact a trained and qualified Volvo service technician. Erase the message by pressing READ, see page 60. Information symbol The yellow information symbol lights up to alert the driver to a message in the information dis- play. This symbol illuminates when the vehicle is traveling at speeds below 5 mph (7 km/h). The message can be erased by pressing the READ button, see page 60, or will disappear automatically (the length of time required for the message to disappear varies, depending on the function indicated). When the message "TIME FOR REGULAR SERVICE" is displayed, the text can be erased and the information symbol light can be turned off by pressing the READ button. The text will disappear and the symbol light will go out auto- matically after two minutes. 1 On certain engines, the symbol for low oilpressure is not used. Instead, a text warningis provided in the information display, see page 206. (cid:96)(cid:96) 55 02 Instruments and controls Indicator and warning symbols This symbol may also light up in combination with other indicator or warning symbols. 02 NOTE The car can still be driven after the informa- tion symbol has come on. The car can be driven for 1–2 weeks after service-related information has been displayed. 56 02 Instruments and controls Symbols – instrument panel Symbols – left side in your car's behavior. Even so, an uncorrected condition could hurt fuel economy, emission controls, and drivability. Extended driving with- out correcting the cause could even damage other components in your car. 4. Stability system DSTC This indicator symbol flashes when the DSTC (Dynamic Stability and Traction control system) is actively working to stabilize the car, see page 151 for more detailed infor- NOTE mation. 5. Tire Pressure Monitoring System This system monitors inflation pressure in the tires. See page 188 for more information. 6. Fuel level warning light When this light comes on, the vehi- cle should be refueled as soon as possible. Canadian models are equipped with the second symbol. 2. Anti-lock Brake system (ABS) If the warning light comes on, there is a malfunction of the ABS system (the standard braking system will still function). The vehicle should be driven to a trained and qualified Volvo service technician for inspec- tion, see page 149 for additional information. NOTE Canadian models are equipped with the second symbol. 3. Rear fog light This symbol indicates that the rear fog light (located in the driver's side taillight cluster) is on. 1. Malfunction indicator light CHECK ENGINE As you drive, a computer called On-Board Diagnostics II (OBDII) monitors your car's engine, trans- mission, electrical and emission systems. The CHECK ENGINE light will light up if the computer senses a condition that potentially may need correcting. When this happens, please have your car checked by a trained and qualified Volvo service technician as soon as possible. A CHECK ENGINE light may have many cau- ses. Sometimes, you may not notice a change 02 (cid:96)(cid:96) 57 02 Instruments and controls Symbols – instrument panel Symbols – right side NOTE 02 Canadian models are equipped with the second symbol. 2. Parking brake applied This light is on when the parking brake (hand brake) is applied. The parking brake lever is situated between the front seats, see page 75 for more information. 3. SRS system warning light If this light comes on while the car is being driven, or remains on for longer than approximately 10 sec- onds after the car has been started, the SRS system's diag- nostic functions have detected a fault in a seat belt lock or pretensioner, a front airbag, side impact airbag, and/or an inflatable curtain. Have the system(s) inspected by a trained and qualified Volvo service technician as soon as possible. 4. Oil pressure warning light1 If the light comes on while driving, the car, stop the engine immedi- ately, and check the engine oil level. If the oil level is normal and the light stays on after restart, have the car towed to the nearest trained and quali- fied Volvo service technician. After hard driv- ing, the light may come on occasionally when the engine is idling. This is normal, provided it goes off when the engine speed is increased. 5. Seat belt reminder This symbol (and the seat belt reminder light above the rear view mirror) will light up if either front seat occupant has not buckled his/ her seat belt. If the car is not mov- ing, the symbols will go out after approximately 6 seconds. 6. Generator warning light If the light comes on while the engine is running, have the charg- ing system checked by an author- ized Volvo workshop. 7. Brake failure warning light If this light comes on while driving or braking, stop the car as quickly as possible in a safe place, open the hood, and check the brake fluid level in the reservoir, see page 205 for the location of the reservoir. 1 On certain engines, this symbol is not used to indicate low oil pressure. Instead, a text warning is provided in the information display, see also page 206. 58 02 Instruments and controls Symbols – instrument panel NOTE Canadian models are equipped with the second symbol. Door open warning The driver will be alerted if one of the doors, the hood or the liftgate are open or ajar. WARNING If the fluid level is below the MIN mark in the reservoir or if a Brake failure – Service urgent message is displayed in the infor- mation display: DO NOT DRIVE. Have the car towed to a trained and qualified Volvo service technician and have the brake sys- tem inspected. If the BRAKES and ABS warning lights come on at the same time, this could indicate a fault in the brake system. In this case: 1. Stop the car in a suitable place and switch off the engine. 2. Restart the engine. 3. 4. If both warning lights go off, no further action is required and the car can be driven. If both lights remain on after the engine has been restarted, switch off the engine again and check the brake fluid level, see page 205 for the location of the reservoir. At low speeds If the car is moving at a speed of less than approximately 3 mph (5 km/h), the Information symbol in the instrument panel will light up and a message will be shown in the information display indicating which door(s), etc is not completely closed. At higher speeds If the car is moving at a speed above approximately 6 mph (10 km/h), the Warning symbol in the instrument panel will light up and a message will be shown in the information display indicating which door(s), etc is not completely closed. Hood and liftgate If the hood and/or liftgate is not completely closed, the Information symbol in the instrument panel will light up and a message will be dis- played, regardless of the vehicle's speed. 02 59 02 Instruments and controls Information display Messages 02 When an indicator or warning light in the instru- ment panel comes on, a message is also shown in the information display. To read a message: 1. Press the READ button (1). 2. Pressing READ repeatedly enables you to scroll to any other messages that may be stored. 60 NOTE Message Meaning If a message is displayed when e.g. you are using the trip computer, this message must be read before you can access the trip com- puter. SERVICE REQUIREDA Message Meaning STOP SAFELYA HIGH ENGINE TEMP STOP SAFELY SERVICE URGENTA SEE MANUALA Stop the vehicle in a safe place and switch off the engine to help prevent the risk of seri- ous damage. Stop the vehicle in a safe place and switch off the engine to help prevent the risk of seri- ous damage. Take your car to a trained and qualified Volvo service techni- cian for inspection immediately. Refer to your owner's manual. For additional information, please contact your Volvo retailer. BOOK TIME FOR SERVICE TIME FOR REGULAR MAINTE- NANCE MAINTE- NANCE OVER- DUE Take your car to a trained and qualified Volvo service techni- cian for inspection as soon as possible (but preferably before the next scheduled mainte- nance service). Book time for service at an authorized Volvo workshop. This message is affec- ted by the number of miles/km driven, by the number of months, or by the number of engine hours since the service reminder was reset at the most recent regu- larly scheduled service. If the vehicle is not serv- iced according to schedule, the warranty may not apply to dam- aged parts, etc. Message TIME FOR REGULAR MAINTE- NANCE REMINDER CHECK OIL LEVEL Meaning This message is affec- ted by the number of miles/km driven, by the number of months, or by the number of engine hours since the service reminder was reset at the most recent regu- larly scheduled service. Stop as soon as possi- ble and switch off the engine, check the oil level and top up if nec- essary, see page 206. A This is part of the message. Additional information will also be displayed. 02 Instruments and controls Information display 02 61 02 Instruments and controls 12-volt sockets 12-volt socket (front seat) NOTE NOTE 02 The cover should be kept on when the aux- iliary socket is not in use. The 12-volt socket in the rear seat cannot function as a cigarette lighter. Auxiliary equipment The buttons to the left of the 12-volt socket can be used for Volvo-installed optional or auxiliary equipment. 12-volt socket (rear seat) 12-volt socket, auxiliary equipment The 12-volt socket can be used to plug in cer- tain accessories such as cellular telephones, etc. The maximum current is 10 A. The key must be in position I (or higher) for the auxiliary socket to function. Ashtrays/cigarette lighter The auxiliary socket can also be used for a cig- arette lighter1, and ashtrays, which can be pur- chased from your Volvo retailer. 1 Accessory. 62 02 Instruments and controls Pos. Lighting All lighting off. Low beam head- lights (daytime running lights) will automatically come on if the ignition key is in position II. Front and rear parking lights and license plate lights will also be on. High beams can be briefly flashed. The headlights switch off automatically when the ignition key is removed. Parking lights Daytime running lights. High beams and high beam flash can be used in this position. Parking lights The front and rear parking lights can be turned on even when the ignition is switched off. (cid:177) Turn switch (1) to the parking light position. The license plate lights also illuminate when the parking lights are switched on. 1 On Canadian models, the daytime running lights will remain on with the light switch in this position. Lighting panel Headlights 1. Turn the ignition key to position II. 2. The low beam headlights (daytime running lights) illuminate automatically, except when the light switch (1) is in the parking light position1. 02 NOTE See page 65 for information on switching between high and low beams. Brake lights The brake lights come on automatically when the brakes are applied. Fog lights Front fog lights (option) The front fog lights can be used in combination with either the headlights or the parking lights. 1. Turn the ignition key to position II. 2. Press button (3) to turn on the front fog lights. An indicator light in the button illuminates when the front fog lights are on. (cid:96)(cid:96) 63 02 Instruments and controls Lighting panel Rear fog light The single rear fog light is located in the driver's side taillight cluster. The rear fog light will only function in combi- nation with the high/low beam headlights or the optional front fog lights. 1. Turn the ignition key to position II. 2. Press button (5) to turn on the rear fog light. An indicator light in the button illuminates when the rear fog light is on. NOTE The rear fog light is considerably brighter than the normal taillights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters). NOTE To make it easier to read the odometer, trip odometer, clock, and ambient temperature, these gauges illuminate when the vehicle is unlocked and when the key has been removed from the ignition switch. The light- ing will go out when the vehicle is locked. Move the thumb wheel (2) up to increase brightness or down to decrease brightness. Unlocking the fuel filler door With the ignition switched off, press button (4) to unlock the fuel filler door. Please note that the fuel filler door will remain unlocked until the car begins to move forward. An audible click will be heard when the fuel filler door re-locks. Instrument panel lighting The instrument panel lighting illuminates when the ignition is in position II and the light switch (1) is in either position or 02 64 Lever positions Turn signals High/low beam headlights 02 Instruments and controls Left-side steering wheel lever When turning (cid:177) Move the lever as far up or down as pos- sible (to position 2) to start the turn signals. The turn signals will be cancelled automatically by the movement of the steering wheel, or the lever can be returned to its initial position by hand. When changing lanes The driver can automatically flash the turn sig- nals 3 times by: • Moving the turn signal lever up or down to position 1 and releasing it. • Moving the lever up or down to position 2 and immediately back to its original posi- tion. NOTE • This automatic flashing sequence can be interrupted by immediately moving the lever in the opposite direction. • If the turn signal indicator flashes faster than normal, check for a burned-out turn signal bulb. Continuous high beams 1. Turn the ignition key to position II. 2. With the light switch (1) in position see page 63, pull the turn signal lever toward the steering wheel (position 4) to toggle between high and low beams. High beam flash 1. Turn the ignition key to position II. 2. Pull the turn signal lever to position 3. The high beams will remain on until the lever is released. Home safe lighting When you leave your car at night, you can make use of the home safe lighting function to illuminate the area in front of the car. 1. Remove the key from the ignition switch. 2. Pull the direction indicator lever as far as possible towards the steering wheel (to position 4) and release it. 3. Exit the car and lock the doors. The headlights and parking lights will illuminate and remain on for 301, 60 or 90 seconds. The time interval can be changed according to your 02 (cid:96)(cid:96) 65 Turn signals, lane change position Turn signals, position for normal turns High beam flash Toggle between high and low beams, Home Safe lighting 1 Factory setting 02 Instruments and controls Left-side steering wheel lever preferences by using the Personal Settings function, see page 82 for more information. 02 66 02 Instruments and controls • ACTUAL SPEED (current speed in mph, Canadian models only) • DSTC, see page 151 NOTE Warning messages from the car's monitor- ing systems will override the trip computer function. If a warning message is shown in the informa- tion display while you are using the trip com- puter: 1. Acknowledge the message by pressing the READ (button 1). 2. Press READ again to return to the trip computer function. Controls The trip computer functions can be accessed by twisting the thumb wheel (2) one step at a time in either direction. Twisting a final time returns you to the original function. Resetting AVERAGE (average fuel consumption) and AVERAGE SPEED can be reset. 1. Select one of these functions. 2. Press RESET (3). Trip computer MILES TO EMPTY TANK This function shows the approximate distance that can be driven on the fuel remaining in the tank. The calculation is based on average fuel consumption during the last 20 miles (30 km) of driving and the amount of fuel remaining in the tank when the reading was taken. When the message ---- miles to empty tank appears in the display, refuel as soon as pos- sible. AVERAGE This value indicates fuel consumption since the last time the trip computer was reset, by press- ing RESET (button 3). When the engine is switched off, information on fuel consumption is stored and remains in system memory until RESET (button 3) is pressed again. INSTANTANEOUS This value indicates the current fuel consump- tion, based on readings taken once per sec- ond. When the car is not moving, "----" will be displayed. AVERAGE SPEED This value indicates average speed since the last time the trip computer was reset, by press- ing RESET (button 3). When the engine is switched off, information on average speed is stored and remains in system memory until the RESET (button 3) is pressed again. 02 (cid:96)(cid:96) 67 READ (press to acknowledge/confirm/ erase a message) Thumb wheel (used to scroll among the trip computer menus) RESET The trip computer stores information gathered from several systems in your car and has four menus (five on Canadian models) that can be shown in the information display. • MILES TO EMPTY TANK • AVERAGE (average fuel consumption) • INSTANTANEOUS (current fuel con- sumption) • AVERAGE SPEED 02 Instruments and controls Trip computer 02 ACTUAL SPEED (Canadian models only) This function provides the driver with an instan- taneous conversion of the car's current speed from km/h to mph. NOTE Trip computer readings may vary slightly depending on the circumference of the tires on the car, tire inflation, or driving style. 68 Engaging the cruise control function Increasing or decreasing speed NOTE 02 Instruments and controls Cruise control (option) 02 • Cruise control will not function at speeds below 20 mph (30 km/h). • Momentary acceleration, for less than 1 minute (e.g. when passing another car), does not affect cruise control oper- ation. The car will automatically return to the previously set speed when the accelerator pedal is released. The cruise control buttons are located on the left side of the steering wheel hub. NOTE This does not set the vehicle's speed. 1. Press the CRUISE button. CRUISE will appear in the function display in the center of the instrument panel. 2. Press + or – to set the current speed. CRUISE ON will be displayed. Use + or – in the following ways to increase or decrease the vehicle's speed: 1. Press and hold down + or – until the vehicle reaches the desired speed. This will become the set speed when the button is released. 2. Press + or – for approximately a half sec- ond and release the button to increase or decrease vehicle speed by approximately 1 mph (1.6 km/h). Temporarily disengaging the cruise control • Press 0 to temporarily disengage cruise control. CRUISE will appear in the function display. The currently set speed is stored in the sys- tem's memory. Cruise control is also automatically disengaged: • If the speed drops below approximately 20 mph (30 km/h) when driving uphill. • When the brake or clutch pedal is depressed. • If the gear selector is moved to posi- tion N. (cid:96)(cid:96) 69 02 Instruments and controls Cruise control (option) 02 • During wheel spin or wheel lock-up. • If the vehicle's speed is increased by using the accelerator pedal for more than 1 minute. Returning to the set speed Press the button to resume the previously set speed. CRUISE ON will be displayed. Disengaging cruise control Cruise control can also be disengaged by: • Pressing the CRUISE button (CRUISE ON will no longer be shown in the function display). • Putting the gear selector in Neutral (N). WARNING Cruise control should not be used in heavy traffic or when driving on wet or slippery roads. Cruise control may not maintain set speed on steep downgrades. 70 02 Instruments and controls Windshield wipers Manual wiper function Windshield/headlight washers Rain sensor (option) – on/of, see page 71 Thumb wheel Liftgate wiper/washer Windshield wipers off The windshield wipers are off when the lever is in position 0. From position 0, move the lever upward. The windshield wipers will sweep one stroke at a time for as long as the lever is held up. Intermittent wiper function With the lever in this position, you can set the wiper interval by mov- ing the thumb wheel (C) upward to increase wiper speed or down- ward to decrease the speed. Continuous wiper function The wipers operate at "normal" speed. High speed wiper function. A–Windshield washers Pull the lever toward the steering wheel and release it. The wipers will make 2–3 sweeps across the windshield after the lever has been released. Right-side steering wheel lever CAUTION • Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers are in operation. • Before using the wipers, ice and snow should be removed from the wind- shield/rear window. Be sure the wiper blades are not frozen in place. 02 Headlight washers (certain models) When the lever has been pulled, high pressure jets mounted in the bumper will spray the head- lights. The following applies to conserve washer fluid, see page 63 for information on the light switch positions: Low/high beam headlights on The headlights will be washed the first time the windshield is washed. Thereafter, the head- lights will only be washed once for every five times the windshield is washed within a 10- minute period. Parking lights on Optional Bi-Xenon(cid:159) headlights will be washed once for every five times the windshield is washed. Normal halogen headlights will not be washed. (cid:96)(cid:96) 71 02 Instruments and controls Right-side steering wheel lever B – Rain sensor (option) 02 The rain sensor regulates windshield wiper speed according to the amount of water on the windshield. The sensitivity of the rain sensor is adjusted by moving the thumb wheel (C in the illustration on the previous page) up (the wipers will sweep the windshield more frequently) or down (the wipers will sweep the windshield less frequently). On/Off Activating the rain sensor 1. Switch on the ignition. 2. Put the windshield wiper lever in position 0. 72 3. Press button B (see page 71). The rain sen- sor symbol will appear in the lower display. Manual deactivation The rain sensor can be deactivated by: • Pressing button (B). or • Moving the windshield wiper lever down. NOTE The rain sensor function will remain acti- vated if the lever is briefly moved up to activate the "manual sweep" function. CAUTION The rain sensor should be deactivated when washing the car in an automatic car wash, etc. If the rain sensor function is left on, the wipers will start inadvertently in the car wash and could be damaged. Automatic deactivation The rain sensor is deactivated automatically in the following situations: • When the key is removed from the ignition. • Five minutes after the ignition is switched off if the key is left in the ignition. C – Thumb wheel The thumb wheel is used to set the wiper inter- val when intermittent wiping is selected, or the sensitivity to the amount of rain on the wind- shield when the rain sensor is selected. Move the wheel upward or downward to increase/ decrease wiper speed when the intermittent function is selected, or to increase/decrease the optional rain sensor's sensitivity when the this function is activated. D – Liftgate wiper/washer Press the lever forward to wipe and wash the liftgate window. The wiper will sweep the win- dow several times after the lever has been released. The button at the end of the lever has three positions: • Intermittent wiping: Press in the upper sec- tion of the button. • Normal wiper speed: Press in the lower section of the button. • Neutral position: The wiper function is switched off. 02 Instruments and controls Right-side steering wheel lever Liftgate wiper and reverse gear • If the front wipers are on and the transmis- sion is put into reverse gear, the liftgate wiper will be activated. • If the transmission is in reverse and the manual windshield wiper function is used (the lever is pushed upward), the liftgate wiper will also be activated for as long the lever is held up. • If the liftgate wiper is already in normal wip- ing function, the normal wiping function will continue. 02 73 02 Instruments and controls Steering wheel adjustment, Hazard warning flashers Steering wheel adjustment 02 Check that the steering wheel is locked in the new position. WARNING Never adjust the steering wheel while driv- ing. Hazard warning flashers NOTE • Regulations regarding the use of the hazard warning flasher may vary, depending on where you live. • The hazard warning flashers will be acti- vated automatically if an airbag deploys. Both the height and the reach of the steering wheel can be adjusted to a comfortable posi- tion for the driver. 1. Pull down the lever on the steering column to release the steering wheel. 2. Adjust the steering wheel to a suitable position 3. Press the lever back into place to lock the steering wheel in the new position. If nec- essary, press the steering wheel slightly while pressing the lever into the locked position. The four-way flasher should be used to indi- cate that the vehicle has become a traffic haz- ard. To activate the flashers, press the triangu- lar button in the center dash. Press the button again to turn off the flashers. 74 02 Instruments and controls Parking brake (hand brake) The parking brake lever is located between the front seats. NOTE 4. If the vehicle rolls, the parking brake lever must be pulled more firmly. 5. When parking a vehicle always put the gear selector in first gear (for manual transmis- sion) or P (for automatic transmission). Parking on a hill • If the vehicle is pointing uphill, turn the front wheels so that they point away from the curb. • If the vehicle is pointing downhill, turn the front wheels so that they point toward the curb. Releasing the parking brake 1. Press firmly on the brake pedal. 2. Pull the lever up slightly, press the button at the end of the lever and lower the lever completely. The indicator light will illuminate even if the parking brake has only been partially applied. WARNING Pull up the parking brake lever up firmly to its full extent. When applying the parking brake 1. Press firmly on the brake pedal. 2. Pull the parking brake lever up firmly to its full extent. 3. Release the brake pedal and ensure that the vehicle is at a standstill. Parking brake 02 75 02 Instruments and controls Power windows Operation 02 Control panel in driver's door Power window controls The power windows are controlled by buttons in the arm rests. • The ignition must be ON (ignition key in position I, II or the engine running) for the power windows to function. • The power windows will also function after the ignition has been switched off as long as neither of the front doors has been opened. 76 Opening a window Lightly press down the front edge of either of the buttons (A) to the first detent ("stop") to open a window to the position of your choice. WARNING • Always remove the ignition key when the vehicle is unattended. • Never leave children unattended in the vehicle. • Make sure that the windows are com- pletely unobstructed before they are operated. • Press the front part of any of the buttons (A) as far down as possible and release to automatically open the window com- pletely. • To stop the window at any time, pull the button up. Closing a window • Lightly pull up the front edge of any of the buttons (A) to the first detent ("stop") to close a window to the position of your choice. • Pull the front part of any of the buttons (A) up as far as possible and release to auto- matically close the window completely. To stop the window at any time, press the but- ton down. Power window control – front passenger's side The control for the power window in the front passenger's door operates that window only. Rearview mirror Rearview mirror with compass (option) Calibrating the compass Mirrors 02 02 Instruments and controls Day/night control Normal position Night position, reduces glare from follow- ing traffic Night position To reduce glare from the headlights of follow- ing vehicles, use control (1) to switch between the normal and night-driving positions. Auto-dim function (option) An optional integrated sensor reacts to head- lights from following traffic and automatically reduces glare. The upper right-hand corner of the rearview mirror has an integrated display that shows the compass direction toward which the car is pointing. Eight different directions can be dis- played: N, NE, E, SE, S, SW, W and NW. The display shows your car's orientation with respect to true north. The earth is divided into 15 magnetic zones. The compass is initially set for the zone to which the car was delivered, and should always be adjusted if the car is driven to a new magnetic zone. A "C" will be displayed if cali- bration becomes necessary. To calibrate the compass: 1. Stop the car in a large, open area, away from traffic. 2. Using a pen or similar object, hold the but- ton (1) depressed for at least 6 seconds. "C" will be displayed. (cid:96)(cid:96) 77 02 Instruments and controls Mirrors 02 Power door mirrors Magnetic zones 3. Press button (1) for at least 3 seconds to display the number of the current magnetic zone. 4. Press button (1) repeatedly until the num- ber for the required geographical area (1 – 15) is displayed. "C" will be displayed again. 5. Drive slowly in a circle at a maximum speed of 6 mph (10 km/h) until a compass direc- tion is displayed. Calibration is complete. The mirror control switches are located on the driver's door armrest. Adjusting the mirrors WARNING • The mirrors should always be adjusted prior to driving. • Objects seen in the passenger's side wide-angle door mirror are closer than they appear to be. 78 Driver's door mirror: (cid:177) Press the L button (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the driver's door mirror. Passenger's door mirror: 1. Press the R switch (a light in the switch will go on) to activate the adjustment control. Use this control to adjust the passenger's door mirror. 2. After you have adjusted the mirror(s), press the L or R switch again (the LED will go out) to deactivate the adjustment control. Storing the mirrors' position The position of the door mirrors is stored when the vehicle is locked. The next time the driver's door is unlocked with the same remote control and that door is opened within 2 minutes, the optional power driver's seat and side door mir- rors will automatically move to the position that they were in when the doors were most recently locked with the same remote control. Folding power door mirrors (option on certain markets only) The mirrors can be folded in for parking/driving in narrow spaces. 02 Instruments and controls Folding the mirrors in 1. Press down the L and R mirror control but- tons on the driver's door at the same time. 2. Release them after approximately one sec- ond. The mirrors automatically fold in to the fully retracted position. Folding the mirrors out Fold out the mirrors by pressing down the L and R buttons at the same time. The mirrors automatically fold out to the fully extended position. Automatic folding When the vehicle is locked/unlocked with the remote control or with the optional keyless drive system (see page 123), the power door mirrors with automatically fold in or out. NOTE The door mirrors will not fold out automati- cally when the vehicle is unlocked if they were folded in using the buttons on the driv- er's door control panel. This function can be activated/deactivated in Personal settings (see page 82). In the menu system, go to Car settings locking. Fold mirr. when Return to "neutral" position If a mirror has been inadvertently moved (bum- ped in a parking lot, etc.) from its original (neu- tral) position, it must be moved back to this position before automatic folding will function again. To so so: 1. Fold in the mirrors by pressing the L and R mirror control buttons on the driver's door at the same time. 2. Fold them out again by pressing the L and R mirror control buttons. This returns the mirrors to their original (neutral) positions. Blind Spot Information System (BLIS) - option The Blind Spot Information System (BLIS) is an information system that indicates the presence of another vehicle in the side-view mirror's "blind area." See page 157 for detailed infor- mation. Mirrors 02 79 02 Instruments and controls Power moonroof (option) Operating the moonroof 02 Moonroof control in the ceiling console To operate the moonroof, the ignition key must first be turned to the intermediate or drive posi- tion (position I, II or the engine running). The moonroof can be opened in two ways: Tilt position Sliding moonroof Auto open Manual open Manual close Auto close Tilt open Tilt close Tilt position Open: Press the rear edge of the control upward to position 5. Close: Pull the rear edge of the control down to position 6. 80 Sliding moonroof Auto open/close Open: Pull the switch as far back as possible (to position 1) and release it to automatically slide open the moonroof. Close: Push the switch as far forward as pos- sible (to position 4) and release it to automati- cally close the moonroof. Manual open/close Open: Pull the switch back to the first stop (position 2) and hold it until the moonroof has opened to the position of your choice. Close: Push the switch forward to the first stop (position 3) and hold it until the moonroof has closed to the position of your choice, or has closed completely. NOTE If the moonroof is repeatedly obstructed during auto-close operation, an overload circuit breaker will temporarily halt moon- roof function. The moonroof will return to normal function after a brief cool-down period. 02 Instruments and controls Power moonroof (option) Visor The optional moonroof features a sliding visor. The visor slides open automatically when the moonroof is opened, and must be closed man- ually. CAUTION • Remove ice and snow before opening the moonroof. • Do not operate the moonroof if it is fro- zen closed. • Never place heavy objects on the moonroof. WARNING • If the moonroof is obstructed during auto-close operation, it will automati- cally reverse direction and return to its starting position. • During manual closing, if the moonroof is obstructed, immediately open it again. WARNING • Never open or close the moonroof if it is obstructed in any way. • Never allow a child to operate the moonroof. • Never extend any object or body part though the open moonroof, even if the vehicle's ignition is completely switched off. • Never leave a child alone in a vehicle. 02 81 02 Instruments and controls Personal settings Control panel 02 Display Menu button Exit button Enter button Menu navigation controls 82 Personal settings can be made for some of the car's functions, such as the central locking system, climate control, and the audio system. Please refer to page 231 for more information on the audio functions that can be adjusted. The settings are presented in the display (A). To access the menu and adjust settings 1. Press MENU (B). 2. Scroll to Car Settings using the menu nav- igation control (E). 3. Press ENTER (D). 4. Select an alternative using the menu navi- gation control (E). 5. Confirm your selection by pressing ENTER. To exit the menu Press EXIT (C). Available settings Clock adjust To set the time: 1. Use the number keys or the up/down arrow keys on the navigation control (E) to change the hour or minute. 2. Select hour(s) or minute(s) to be changed with the left/right arrow keys. 3. Press ENTER to start the clock. NOTE If you are currently using the 12-hour time setting, use the up/down arrow keys to select AM/PM after the minute-setting has been adjusted. Lock confirmation light When the car is locked/unlocked with the remote control, the direction indicators can be selected to flash to confirm the action. The alternatives On/Off are available for both lock- ing and unlocking. Autolock When the car starts to move, the doors and liftgate can be locked automatically. The alter- natives On/Off are available. NOTE Pulling the handle twice on a door unlocks and opens that door. Unlock There are two alternatives for unlocking: 02 Instruments and controls • Global (All doors) – unlocks all doors and the liftgate with one press on the remote control. • Two Step (Two-stage unlocking) – This alternative unlocks the driver's door with one press on the remote control. A second press unlocks the passenger's door and the liftgate. Automatically folding the door mirrors The setting makes it possible to automatically fold the door mirrors in or out when the vehicle is locked or unlocked. See page 78. Operating side windows The following alternative can be selected for opening the door windows at the same time by pressing and holding the Unlock switch in either of the front doors (see page 127 for additional information) 1 NOTE The ignition key must be in position I or higher (see page 141) before the door win- dows can be opened using the switches in the doors. • Auto open all windows On/Off Temporarily turning off the alarm sensor(s) The alarm sensors can be temporarily turned off (if, for example, a person or a pet remains in the vehicle when the doors are locked from outside with the remote control). There are two alternatives:Activate once and Ask on exit, see page 118 and 129 . Approach lighting This alternative determines the length of time for which the car's lights will remain on when the Approach light button on the central lock- ing system's remote control is pressed. Inter- vals of 30/60/90 seconds may be selected, see teh section "Remote control functions" for more information. Home safe lighting This alternative determines the length of time for which the car's lights will remain on when the high beam lever on the steering column is pulled toward the wheel with the ignition switched off. Intervals of 30/60/90 seconds may be selected, see page 65 for information on using this function. Personal settings Information • VIN number – The VIN (Vehicle Identifica- tion Number) is the car's unique identity number. • Number of Keys – the number of keys reg- istered for the car is displayed here. Climate functions • Blower speed in AUTO mode – the blower speed can be set to AUTO mode in models equipped with ECC. Choose between "Low", "Normal" and "High". • Timer for recirculation – when the timer is active, the air recirculates in the car for 3– 12 minutes depending on the ambient tem- perature. Select On/Off depending on whether the recirculation timer is to be active or not. Keyless locking and unlocking (option as available) The following alternatives can be selected for locking and unlocking the doors and liftgate: • All doors – all doors are locked or unlocked at the same time. • Doors on the same side – front and rear doors on the same side are unlocked together. 1 This menu alternative also makes it possible to open both door windows by pressing and holding the Unlock button on the remote control for several seconds. 02 (cid:96)(cid:96) 83 02 Instruments and controls Personal settings 02 • Both front doors – both front doors are unlocked together. • One front door – either of the front doors can be unlocked separately2. Reset to factory settings Use this alternative to return to the default cli- mate system settings. 2 Factory default. 84 Introduction The HomeLink Wireless Control System pro- vides a convenient way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as gate opera- tors, garage door openers, entry door locks, security systems, even home lighting. Addi- tional HomeLink information can be found on the Internet at www.homelink.com. 02 Instruments and controls HomeLink® Wireless Control System (option) WARNING • If you use HomeLink to open a garage door or gate, be sure no one is near the gate or door while it is in motion. • When programming a garage door opener, it is advised to park outside of the garage. • Do not use HomeLink with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manu- factured before April 1, 1982). A garage door that cannot detect an object - sig- naling the door to stop and reverse - does not meet current U.S. federal safety standards. For more information, contact HomeLink at: www.homelink.com. Retain the original transmitter of the RF device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. Refer to “Erasing HomeLink Buttons”. Programming HomeLink NOTE 02 Some vehicles may require the ignition switch to be turned on or to the second (“accessories”) position for programming and/or operation of HomeLink. It is also rec- ommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1. Position the end of your hand-held trans- mitter 1–3 inches (5–14 cm) away from the HomeLink button you wish to program while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink and hand-held transmit- ter buttons until the HomeLink indicator light changes from a slow to a rapidly blink- ing light. Now you may release both the HomeLink and hand-held transmitter but- tons. (cid:96)(cid:96) 85 02 Instruments and controls HomeLink® Wireless Control System (option) 02 NOTE Some devices may require you to replace this Programming Step 2 with procedures noted in the “Gate Operator / Canadian Pro- gramming” section. If the HomeLink indica- tor light does not change to a rapidly blinking light after performing these steps, contact HomeLink at www.homelink.com. 3. Firmly press, hold for five seconds and release the programmed HomeLink but- ton up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink button and observe the indicator light. • If the indicator light stays on con- stantly, programming is complete and your device should activate when the HomeLink button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a con- stant light continue with “Program- ming” steps 4-6 to complete the pro- gramming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor- head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) There are 30 seconds to initiate step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the pro- grammed HomeLink button. Repeat the “press/hold/release” sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process. HomeLink should now activate your rolling code equipped device. Gate Operator/Canadian Programming Canadian radio-frequency laws require trans- mitter signals to “time-out” (or quit) after sev- eral seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. If you live in Canada or you are having difficul- ties programming a gate operator or garage door opener by using the “Programming” pro- 86 cedures, replace “Programming HomeLink” step 2 with the following: • Continue to press and hold the HomeLink button while you press and release - every two seconds (“cycle”) your hand- held transmitter until the HomeLink indica- tor light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink and hand-held transmitter buttons. Proceed with “Programming” step 3 to com- plete. Using HomeLink To operate, simply press and release the pro- grammed HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficul- ties or questions, contact HomeLink at: www.homelink.com. 02 Instruments and controls HomeLink® Wireless Control System (option) This device complies with FCC rules part 15 and Industry Canada (IC) RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) This device must accept any

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Volvo C30 Owners Manual