2008 Toyota Yaris Sedan Owners Manual

Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using a seat belt or a child restraint lower anchorage. Attach the top strap when installing a child restraint.

Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 41)

Child restraint ages

lower anchor-

for

the outside

Lower anchorages are pro- vided rear seats. (Buttons displaying the location of the anchorages are attached to the seats.)

Anchor bracket (for top strap) Anchor brackets are provided for all rear seats.

87

1-7. Safety information

Installing child restraints using a seat belt (child restraint lock function belt)

n Rear facing ⎯ Infant seat/convertible seat

Place the child seat on the rear seat facing the rear of the vehi- cle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

then allow

Fully extend the shoulder belt and to retract slightly in order to activate the ALR lock mode.

it

Lock mode allows the seat belt to retract only.

88

1

1-7. Safety information

While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

n Forward facing ⎯ Convertible seat

the head

Remove restraint. Place the child seat on the seat facing the front of the vehicle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

it

then allow

Fully extend the shoulder belt and to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.

89

1-7. Safety information

n Booster seat

90

While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.

Place the booster seat on the seat facing the front of the vehi- cle.

Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child's shoulder, and that the lap belt is as low as possible. (→P. 41)

1-7. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Installation with child restraint lower anchorages

Remove the head restraint.

91

1-7. Safety information

Type A

Canada only

Type B

Canada only

92

Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the anchorages and tighten the lower straps. If the child restraint has a top strap, top strap should be latched onto the anchor bracket. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

the

Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the anchorages. If the child restraint has a top strap, top strap should be latched onto the anchor bracket. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.

the

1-7. Safety information

Child restraint systems with a top strap

Secure the child restraint using a seat belt or lower anchors, and remove the head restraint.

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top strap. is

top strap

Make sure the securely latched.

n Laws and regulations pertaining to anchorages

Anchorages conform to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

93

1-7. Safety information

CAUTION

n When installing a booster seat

Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 44) l ALR mode causes the belt to tighten only which could cause injury or dis-

comfort to the child.

l Do not allow the child to play with the seat belt or the child could be killed

or seriously injured.

n When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking or an accident.

If the driver's seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

l Only put a forward facing or booster child seat on the front seat when unavoidable. When installing a forward facing or booster child seat on the front passenger seat, move the seat as far back as possible even if AIR BAG OFF indicator light is illuminated. Failing to do so may result in death or serious injury if the airbags deploy (inflate).

l When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Failing to do so may result in death or serious injury in the event of an accident or sudden braking.

94

1-7. Safety information

CAUTION

n When installing a child restraint system

l Ensure that the belt and tab are securely locked and the seat belt is not

twisted.

l Push and pull the child restraint system in different directions to be sure it

is secure.

l Follow all installation instructions provided by the child restraint system

manufacturer.

n Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of a colli- sion.

n To correctly attach a child restraint system to the anchorages

When using the lower anchorages, be sure that there are no foreign objects around the anchorages and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop or accident.

95

1-7. Safety information

96

2-1. Driving procedures Driving the vehicle

The following procedures should be observed to ensure safe driv- ing. n Starting the engine (→ P. 108) n Driving

Automatic transmission

With the brake pedal depressed, shift the shift lever to D.

Release the parking brake.

(→P. 112) (→P. 116) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.

Manual transmission

With the clutch pedal fully depressed, shift the shift lever to (→P. 114) 1. Release the parking brake. (→P. 116) Gradually release the clutch pedal. At the same time, gently depress the accelerator pedal to accelerate the vehicle.

n Stopping

Automatic transmission

With the shift lever in D, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, shift the shift lever to P or N. (→P. 112)

Manual transmission

With the clutch pedal fully depressed, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, shift the shift lever to N. (→P. 114)

98

2

2-1. Driving procedures

n Parking the vehicle

Automatic transmission

With the shift lever in D, depress the brake pedal. Set the parking brake. Shift the shift lever to P. When parking on a hill, if necessary, block the wheels. Turn the engine switch off to stop the engine. Lock the door, making sure that you have the key on your person.

(→P. 116) (→P. 112)

Manual transmission

With the clutch pedal fully depressed, depress the brake pedal. (→P. 116) Set the parking brake. (→P. 114) Shift the shift lever to N. When parking on a hill, shift the shift lever to 1 or R. If necessary, block the wheels. Turn the engine switch off to stop the engine. Lock the door, making sure that you have the key on your person.

Starting on a steep uphill

Automatic transmission

With the brake pedal depressed, firmly set the parking brake and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

Manual transmission

With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1.

99

2-1. Driving procedures

Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal. Release the parking brake.

n Driving in the rain

l Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

l Drive carefully when it starts to rain, because the road surface will be

especially slippery.

l Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

n Breaking in your new Toyota

To extend the life of the vehicle, the following precautions are recommended to observe: l For the first 200 miles (300 km):

Avoid sudden stops.

l For the first 500 miles (800 km):

Do not tow a trailer.

l For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in the low gears. • Do not drive at a constant speed for extended periods.

n Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 328)

n Normal characteristics after turning off the engine

Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.

100

2

2-1. Driving procedures

CAUTION

n When starting the vehicle

Vehicles with an automatic transmission, always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

n When driving the vehicle

l Do not drive if you are unfamiliar with the location of the clutch, brake and

accelerator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

l Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.

l Vehicles with an automatic transmission, do not let the vehicle roll back- wards while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle. If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.

101

2-1. Driving procedures

CAUTION

n When driving the vehicle

l Do not under any circumstances shift the shift lever to P, R or N (automatic

transmission) or R (manual transmission) while the vehicle is moving. Doing so can cause significant damage to the transmission system and may result in a loss of vehicle control.

l Do not shift the shift lever to N while the vehicle is moving.

Doing so may cause the engine brake to not operate properly and lead to an accident.

l Do not turn the engine off while driving.

The power steering and brake booster systems will not operate properly if the engine is not running.

l Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 112,114)

l When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.

l Do not adjust the position of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.

l Always check that all passengers' arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. l Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. n When driving on slippery road surfaces

l Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

102

2-1. Driving procedures

CAUTION

n When driving on slippery road surfaces

l Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.

l After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

n When shifting the shift lever

Vehicles with an automatic transmission, be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

n When the vehicle is stopped

l Do not race the engine.

If the vehicle is in any gear other than P (automatic transmission only) or N, the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.

l Do not leave the vehicle with the engine running for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

l Vehicles with an automatic transmission, always keep a foot on the brake pedal while the engine is running to prevent an accident caused by the vehicle moving.

103

2-1. Driving procedures

CAUTION

n When the vehicle is parked

l Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following. • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of eye glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle's electrical components.

l Always apply the parking brake, shift the shift lever to P (automatic trans-

mission only), stop the engine and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

l Do not touch the exhaust pipe while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

l Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

n Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard.

If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

l The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.

104

2-1. Driving procedures

CAUTION

n When taking a nap in the vehicle

Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

n When braking the vehicle

l When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle. If the power brake assist function does not operate, do not follow other vehicles closely and avoid downhills or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

l Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

l The brake system consists of 2 individual hydraulic systems: If one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

105

2-1. Driving procedures

NOTICE

n When driving the vehicle

Vehicles with a manual transmission

l Do not rest your foot on the clutch pedal while driving.

Doing so may cause clutch trouble.

l Do not use any gears other than the first gear when starting off and mov-

ing forward. Doing so may damage the clutch.

l Do not use the clutch to hold the vehicle when stopping on an uphill grade.

Doing so may damage the clutch. Vehicles with an automatic transmission

l Do not use the accelerator pedal or depress accelerator and brake pedals

together to hold the vehicle on a hill.

n When parking the vehicle

Vehicles with an automatic transmission: Always put the shift lever in P. Failure to do so may cause the vehicle to move or the vehicle may acceler- ate suddenly if the accelerator pedal is accidentally depressed.

n Avoiding damage to vehicle parts

l Do not turn the steering wheel fully in either direction and hold it there for a

long time. Doing so may damage the power steering motor.

l When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

n If you hear a squealing or scraping noise while driving (brake pad wear

limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or that of the brake discs are exceeded.

106

2-1. Driving procedures

NOTICE

n If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. It may be difficult to control your vehicle. l The vehicle will make abnormal sounds. l The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 305)

n When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. l Engine stalling l Short in electrical components l Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. l Brake function l Changes in quantity and quality of engine oil, transaxle fluid, etc. l Lubricant condition for the bearings and suspension joints (where possi-

ble) and the function of all joints, bearings, etc.

107

2-1. Driving procedures Engine (ignition) switch

n Engine switch

LOCK The steering wheel is locked and the key can be removed. ACC Some electrical components such as the audio system can be used. ON All electrical components can be used. START For starting the engine.

n Starting the engine

Automatic transmission

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the START position and start the engine. The engine will crank until it starts or for up to 20 seconds, which- ever is less. Continue depressing the brake pedal until the engine is com- pletely started.

108

2

2-1. Driving procedures

Manual transmission

Check that the parking brake is set. Check that the shift lever is set in N. Firmly depress the brake pedal and clutch pedal. Turn the engine switch to the START position and start the engine. The engine will crank until it starts or for up to 20 seconds, which- ever is less. Continue depressing the brake pedal and clutch pedal until the engine is completely started.

109

2-1. Driving procedures

n Turning the key from ACC to LOCK

n Steering lock release

Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). (→P. 112, 114) Push in the key and turn to the LOCK position.

When starting the engine, the engine switch may seem stuck in the LOCK posi- tion. To free it, turn the key while turning the steering wheel slightly in either direc- tion.

n If the engine does not start (vehicles with engine immobilizer system) The engine immobilizer system may not have been deactivated. (→P. 59)

n Key reminder function

A buzzer sounds if the driver’s door is opened, while the engine switch is in the ACC or LOCK position to remind you to remove the key.

CAUTION

n When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

110

2-1. Driving procedures

CAUTION

n Caution while driving

Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position.

NOTICE

n To prevent battery discharge

Do not leave the engine switch in the ACC or ON position for long periods if the engine is not running. n When starting the engine

l Do not crank for more than 30 seconds at a time. This may overheat the

starter and wiring systems. l Do not race a cold engine.

If the engine becomes difficult to start or stalls frequently, have the engine checked immediately.

111

2-1. Driving procedures Automatic Transmission (if equipped)

Select a shift position appropriate for the driving conditions. n Shifting the shift lever

While the engine switch is on, depress the brake pedal and

move the shift lever.

112

2

2-1. Driving procedures

n Shift position uses

Shift position

Function

Parking the vehicle or starting the engine

Reversing Neutral

Normal driving*

Position for engine braking

Position for more powerful engine braking

Position for maximum engine braking

*: To improve fuel consumption and reduce noises, set the shift lever in

D for normal driving.

n Downshifting restrictions

The shift lever cannot be downshifted if the following speeds are exceeded. mph (km/h)

Downshifting

Maximum speed

3→2
2→L

53 (86) 26 (43)

n When driving with the cruise control system

The engine brake will not operate when downshifting from D to 3.(→P. 132)

n If the shift lever cannot be shifted from P (→P. 315)

113

2-1. Driving procedures Manual Transmission (if equipped)

n Shifting the shift lever

Fully depress the clutch pedal before operating the shift lever, and then release it slowly.

n Maximum allowable speeds

Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary.

mph (km/h)

Shift position

Maximum speed

31 (51) 59 (95) 86 (139)

114

2

2-1. Driving procedures Turn signal lever

Left turn Right turn Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever.

n Turn signals can be operated when

The engine switch is in the ON position.

n If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

115

2-1. Driving procedures Parking brake

n Set the parking brake

Fully set the parking brake while depressing the brake pedal.

At this time, the indicator will come on.

Except Canada

Canada

n Release the parking brake

Slightly raise the lever Press the button Lower it completely

116

2-1. Driving procedures

NOTICE

n Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear. l Parking brake engaged warning buzzer (→P. 292)

117

2-2. Instrument cluster Gauges and meters

Vehicles with tachometer

The following gauges, meters and displays illuminate when the engine switch is in the ON position.

Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Clock Indicates the time.

118

2

2-2. Instrument cluster

Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently. ODO/TRIP button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played. CLOCK button Adjusts the time. (→P. 201)

119

2-2. Instrument cluster

Vehicles without tachometer

Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Clock Indicates the time. Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehi- cle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.

120

2

2-2. Instrument cluster

ODO/TRIP button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played. CLOCK button Adjusts the time. (→P. 201)

Odometer and trip meter display button

Pressing this button switches between odometer and trip meter dis- plays.

Odometer Trip meter A* Trip meter B* *:Pushing and holding the button will reset the trip meter.

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker If the dial is turned up until a click is heard, tachometer and speedometer will no longer be illuminated when the tail lights/ head lights are turned on.

the

121

2-2. Instrument cluster

NOTICE

n To prevent damage to the engine and its components

l Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

l The engine may be overheating if the high engine coolant temperature warning light comes on. In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 320)

122

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster (vehicles with tachometer)

Instrument cluster (vehicles without tachometer)

123

2-2. Instrument cluster

Center panel

124

2

2-2. Instrument cluster

n Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Low engine coolant temperature indicator Indicates the engine coolant temperature is cool.

Cruise control indicator (→P. 132)

AIR BAG ON indicator (→P. 78)

AIR BAG OFF indicator (→P. 78)

(if equipped)

Turn signal indicator (→P. 115)

Headlight high beam indicator (→P. 127)

Headlight indicator (→P. 127)

Tail light indicator (→P. 127)

Front fog light indicator (→P. 129)

(except Canada)

(Canada)

(if equipped)

(Automatic transmission vehicles with tachometer) Shift position and shift range indica- tors (→P. 112)

(Automatic transmission vehicles without tachometer) Shift position and shift range indica- tors (→P. 112)

125

2-2. Instrument cluster

n Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 292)

(Canada -if equipped)

(except Canada -if equipped)

(Canada)

(except Canada)

(Canada)

(except Canada)

(if equipped)

(except Canada)

(except Canada)

(vehicles with tachom- eter)

(vehicles without tachometer) *: These lights turn on when the engine switch is turned to the ON position to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

CAUTION

n If a safety system warning light does not come on

Should a safety system light such as ABS and the SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

126

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

(except Canada)

(Canada)

The side marker, parking, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on.

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

127

2-3. Operating the lights and wipers

n Daytime running light system (if equipped)

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the engine is started and the parking brake is released. Daytime running lights are not designed for use at night.

n Light reminder buzzer

A buzzer sounds when the key is removed and the driver's door is opened while the lights are turned on.

NOTICE

n To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

128

2-3. Operating the lights and wipers Fog light switch (if equipped)

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. n Front fog light switch

OFF Front fog lights ON

129

2-3. Operating the lights and wipers Windshield wipers and washer

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

Washer/wiper dual operation

Wipers will automatically oper- ate a couple of times after the washer squirts.

n The windshield wiper and washer can be operated when

The engine switch must be in the ON position.

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

130

2-3. Operating the lights and wipers

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. n When a nozzle becomes block

Do not try to clear it with a pin or other object. The nozzle will be damaged.

131

2-4. Using other driving systems Cruise control (if equipped)

Use cruise control to maintain a set speed without using the acceler- ator. n Set the vehicle speed

Press the ON-OFF button to turn the cruise control on.

At this time, the cruise control indicator will come on. Press the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

n Adjusting the speed setting

132

2

2-4. Using other driving systems

n Canceling and resuming regular acceleration

Cancel Push the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied clutch depressed (manual transmis- sion). Resume To resume cruise control and return to the set speed, push the lever up.

the

or

n Cruise control can be set when

l The shift lever is in D or 3 (vehicles with an automatic transmission). l Vehicle speed is above approximately 25 mph (40 km/h).

n Accelerating

The vehicle can be accelerated normally. n Automatic cruise control cancelation

The set speed is automatically cancelled in any of the following situations. l Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

l Actual vehicle speed is below 25 mph (40 km/h).

n If the cruise control indicator light flashes

Press the ON-OFF button to turn the cruise control off, and then reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

133

2-4. Using other driving systems

CAUTION

n To avoid operating the cruise control by mistake

Keep the ON-OFF button off when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause seri- ous or fatal accident. l On roads with sharp bends l On winding roads l On slippery roads, such as those covered with rain, ice or snow l On steep hills

n While driving with the cruise control on

Vehicles with a manual transmission, do not shift to neutral without depress- ing the clutch pedal, as this may cause engine racing or overrevving.

134

2

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. n ABS (Anti-lock Brake System) (if equipped)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

n EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

n Sounds and vibrations caused by the ABS

l A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in this system.

l Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

n EPS operation sound

When the steering wheel operates, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.

n Reduced effectiveness of EPS

The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The sys- tem should return to normal within 10 minutes.

135

2-4. Using other driving systems

CAUTION

n The ABS does not operate effectively when

l Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

l The vehicle hydroplanes while driving at high speed on the wet or slick

road.

n Stopping distance when the ABS is operating on the wet or slick roads The ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. l When driving on dirt, gravel or snow-covered roads l When driving with tire chains l When driving over bumps in the road l When driving over roads with potholes or uneven roads

n Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the appro- priate tire pressure level. The ABS will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

n Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

136

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. l Stow cargo and luggage in the trunk whenever possible. l Be sure all items are secured in place. l Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

l For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) − (Total weight of occupants) Steps for Determining Correct Load Limit— (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

137

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Except Canada: Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 845 lb. (383
kg), the available amount of cargo and luggage load capacity will be as follows: 845 lb. − 366 lb. = 479 lb. (383 kg − 166 kg = 217 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

479 lb. − 388 lb. = 91 lb. (217 kg − 176 kg = 41 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

138

2-5. Driving information

CAUTION

n Things that must not be carried in the trunk

The following things may cause a fire if loaded in the trunk. l Receptacles containing gasoline l Aerosol cans

n Storage precautions

l Do not place anything on the package tray behind the rear seatback.

Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

l Do not drive with objects on top of the instrument panel.

They may interfere with the driver’s field of view or move during sharp acceleration or turning, thus impairing the driver’s control of the vehi- cle. In an accident they may injure the vehicle occupants.

l Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

n Capacity and distribution

l Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

l Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

139

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. n Total load capacity: 845 lb. (383 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

n Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity.

n Towing capacity (Canada): 700 lb. (318 kg)

Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

n Towing capacity (except Canada):

Toyota does not recommend towing a trailer with your vehicle.

n Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

n Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 246)

CAUTION

n Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

140

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. n Pre-winter preparations

l Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

l Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

l Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. n Before driving the vehicle

Perform the following according to the driving conditions. l Do not try to forcibly open a window, scrape an outside rear view mirror surface or move a wiper or outside rear view mir- ror that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.

l To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

l Remove any ice that has accumulated on the vehicle chassis. l Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

141

2-5. Driving information

n When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

n When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission) or to 1 or R (manual transmission) without setting the parking brake. The parking brake may freeze up, preventing it from being released.

Regulations on the use of snow chains

l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

l Use SAE Class “S” type radial tire chains, with the exception of

radial cable chains or V-bar type chains. • • Refer to the explanation that comes with the tire chains for

Install the chains on the front tires.

installation instructions.

l Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

n Snow chain installation

Observe the following precautions when installing and removing chains.

Install and remove tire chains in a safe location. Install tire chains on the front tires only. Do not install tire chains on the rear tires. Install the tire chains on front tires as tightly as possible. Install tire chains following the instructions provided in the accompanying instructions. If wheel ornaments are used, they will be scratched by the chain band, so remove the ornaments before putting on the chains. (→P. 305)

142

2-5. Driving information

CAUTION

n Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. l Use tires of the size specified for your vehicle. l Maintain the recommended level of air pressure. l Do not drive in excess of 75 mph (120 km/h) regardless of the type of

snow tires being used.

l Snow tires should be installed on all wheels.

n Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. l Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

l Avoid driving on bumpy road surfaces or over potholes. l Avoid sudden turns and braking. l Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

n Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

n Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

143

2-5. Driving information Trailer towing (except Canada)

Toyota does not recommend towing a trailer with your vehicle. Toy- ota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier of a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.

144

2

2-5. Driving information Trailer towing (Canada)

Your vehicle is designed primarily as a passenger-carrying vehicle, thus towing a trailer will have an adverse effect on handling, perfor-