Download PDF Manual


The compass may not show the correct direction in the following conditions: D The vehicle is stopped immediately af-


ter turning. The compass does not adjust while the vehicle is stopped.


D The ignition switch is turned off imme-


diately after turning.


D The vehicle is on an inclined surface. D The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).


D The vehicle is magnetized. (There is a magnet or a metal object on or near the roof.)


D The battery has been disconnected. The compass works to calibrate the direc- tion automatically while the vehicle is in motion, if deviation is small. For additional precision or see calibrating, COMPASS” below.


for complete THE


“CALIBRATING


292


’04 TUNDRA_U (L/O 0309)


the direction


If the system does not operate properly, contact your Toyota dealer.


indicated or


is not


Compass sensor


The compass sensor is on the roof of the vehicle.


NOTICE


Do not put magnets or a metal object on or near the roof of the vehicle. Doing this may cause malfunction of the compass sensor.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


the


from


CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on deviates true direction deter- mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust for this deviation; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature display” in this Section.)


2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 5 sec- onds until the “VAR” indication appears on the compass display.


3. Push


the “E/M” button several


times until the desired zone number appears on the compass display.


If the button is not pushed for 10 sec- onds, the display returns to the compass/ outside temperature mode and the number that is last set is memorized. To select the zone where the vehicle is currently following map.


located, refer


the


to


’04 TUNDRA_U (L/O 0309)


293


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Hawaii: Samoa: Guam: Saipan:


After calibration, leaving the system for several seconds returns to the compass mode.


CAUTION


Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.


Zone number


294


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 10
seconds until the “CAL” indication ap- pears on the compass display. (At this time, the compass display is locked in “N”.)


3. Drive the vehicle in a circle at 8 km/h (5 mph) or less. If there is not enough space to drive in a circle, drive around the block.


When the “CAL” indication goes off and the compass returns to the normal mode, calibration is complete. If you want to restart the calibration be- fore the “MODE” and “E/M” buttons simultaneously for 10 seconds again.


is complete, push both of


it


295


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


the direction display on


CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. In this case, the compass needs to be cali- brated. To calibrate the compass manually, do the following; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature display” in this Section.)


Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. D Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).


in a place where


D During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.


CAUTION


D When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.


D Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.


296


’04 TUNDRA_U (L/O 0309)


Clock


Cigarette lighter and ashtrays


The digital clock indicates the time. The key must be in the “ACC” or “ON” position. To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock). When lights are turned on, the brightness of the time in- dication will be reduced.


instrument panel


the


Cigarette lighter and front ashtray


Rear ashtray


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


CIGARETTE LIGHTER To use the cigarette lighter, press it in. After it finishes heating up, it automati- cally pops out ready for use. If the engine is not running, the key must be in the “ACC” position. Do not hold the cigarette lighter pressed in. Use a Toyota genuine cigarette lighter or equivalent for replacement. ASHTRAYS Front: To use the ashtray, pull it out. Rear: To use the ashtray, raise the lid. When finished with your cigarette, thor- oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, push it back in completely. Front—To remove the ashtray, press down on the lock spring plate and pull out. Rear—To remove the ashtray, pull it out.


CAUTION


in To reduce the chance of case of an accident or sudden stop while driving, always completely close the ashtray after use.


injury


’04 TUNDRA_U (L/O 0309)


Power outlets (12 VDC)


Type A


Type C


Type B


Type D


297


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Power outlet (115 VAC)


The power outlets are designed power supply for car accessories. The key must be in the “ACC” or “ON” position for the power outlets to be used.


for


NOTICE


the


fuse


z To prevent


from being blown, do not use the electricity over the total vehicle capacity of 12V/120W.


z To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.


z Close the power outlet


lids when the power outlets are not in use. Inserting a foreign object other than the appropriate plug that fits the outlet, or allowing any liquid into the outlet may cause electrical fail- ure or short circuits.


298


This power outlet is designed for use as a power supply for electric ap- pliances in the vehicle. The key must be in the “ON” position for the power outlet to be used. The maximum capacity for this power out- let is 115 VAC/100W. If you attempt to use an appliance that requires more than 115 VAC or 100W, the protection circuit will activate and cut the power supply. The power supply will restart automatically when you use an appliance that operates within the 115 VAC/100W limits.


Main switch


To use the power outlet, push the main switch on the instrument panel. An indicator light will illuminate to indicate that the power outlet is ready for use. Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


NOTICE


Certain electrical appliances may cause radio noise.


Glove box


z To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.


z Close the power outlet lid when the power outlet is not in use. Inserting a foreign object other than the ap- propriate plug that fits the outlet may cause electrical failure or short circuits.


The power outlet is not designed for the following electric appliances even though their power consumption is un- der 115 VAC/100W. These appliances may not operate properly. D Appliances with high initial peak watt- age: cathode−ray tube type televisions, compressor−driven refrigerators, electric pumps, electric tools, etc.


D Measuring devices which process pre- cise data: medical equipment, measur- ing instruments, etc.


D Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc.


To open the glove box door, pull the lever. On some models, the glove box light will come on when the glove box is opened with the headlight switch on.


CAUTION


To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.


injury


299


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Garage door opener box


The box is designed to store a garage door opener transmitter. Open the cover and remove the Velcro square.


Remove the paper strip covering the adhe- sive on back side of square and adhere the square to back side of the transmitter near the center.


Please note if transmitter has wire clip for sun visor, this clip must be removed prior to adhesion of the Velcro.


300


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


Place the transmitter with Velcro square facing inside of box into the box. Make sure located above button pins.


transmitter button


the


is


’04 TUNDRA_U (L/O 0309)


Remove spacers from the center panel. Place the largest spacer on the pin that would be below transmitter button when the cover is closed. Close the cover.


When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the center panel of the cover.


301


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


CAUTION


D To reduce the chance of injury in case of an accident or a sudden stop, always keep the garage door opener box closed while driving.


D Keep the remaining spacers away


from children.


Standard and access cab models only— The auxiliary box (stored in the glove box) and garage door opener box are interchangeable. Removing the cover— Half open the cover. Pinch each hinge and pull it out of its pivot one at a time as shown above. Do not remove the cover forcibly.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


If the center panel does not contact your garage door opener transmitter: D Check to see if spacer is on the cor-


rect pin.


D Attach another spacer


top of original spacer. Check operation. If re- quired, continue to add spacers until contact is achieved.


to the


If the transmitter is clattering during driv- ing, fill in a piece of felt or pad to prevent the transmitter from clattering.


302


’04 TUNDRA_U (L/O 0309)


Auxiliary boxes To use the auxiliary boxes, open the lids as shown in the following illustra- tions.


CAUTION


D To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.


D Type A and B only—As these hold- ers are designed for holding a light object such as an eyeglass, do not place any heavy objects in them. Heavy objects may cause the holder to open and contents to fly out re- sulting in injuries.


NOTICE


Type A and B only—During hot weath- er, the interior of the vehicle becomes very hot. Do not leave anything flam- mable or deformable such as a light- er, glasses, etc. inside.


Type A


Type B


Installing the cover— Align the hinges to the pivots, and press each hinge until you hear a click. Make sure that closes smoothly.


the cover opens and


303


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


To fold down the armrest with the auxiliary box


Front


Type E (under the rear seat of access cab models)


To return the armrest with the auxiliary box to the original position


Front


Type C


304


Type D


Type F (under the rear seat of double cab models)


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Rear console box (type A)


UPPER TRAY To access the upper tray, raise the con- sole box lid.


CAUTION


To reduce the chance of in case of an accident or a sudden stop, always keep the upper tray closed while driving.


injury


CONSOLE BOX To access the rear console box, raise the upper tray by pulling up the lock release lever.


CAUTION


To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.


injury


305


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Rear console box (type B)


UPPER TRAY To access the upper tray, raise the con- sole box upper lid while pushing the lock release button.


CAUTION


in To reduce the chance of case of an accident or a sudden stop, always keep the upper tray closed while driving.


injury


CONSOLE BOX To access the rear console box, raise the console box lid by pulling up the lock release lever.


CAUTION


To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.


injury


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


306


’04 TUNDRA_U (L/O 0309)


Coin holder (type A)


Coin holder (type B)


The rear console box is equipped with a coin holder. To use the coin holder: 1. Raise the console box lid. 2. Push coins down into the holder.


307


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


The rear console box is equipped with a coin holder. To use the coin holder: 1. Raise the console box upper lid while


pushing the lock release button. 2. Push coins down into the holder. The coin holder is detachable.


The coin holder can be set in the con- sole box. To set the coin holder in the console box, raise the console box lid by pulling up the lock release lever.


308


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Coin holder (type C)


Compact disc and cassette tape holder (type A)


The auxiliary box is equipped with a coin holder. To use the coin holder: 1. Raise the auxiliary box lid while push-


ing the lock release button.


2. Push coins down into the holder. The coin holder is detachable.


309


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Compact disc and cassette tape holder (type B)


The rear console box is equipped with compact disc and cassette tape holders. To use the holders, raise the console box lid and upper tray by pulling up the lock release lever. The plates for the compact disc and cas- sette tape holders are detachable.


The rear console box is equipped with a compact disc and cassette tape hold- er. To use the holder, raise the console box lid by pulling up the lock release lever. The compact disc and cassette tape hold- er is detachable.


310


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Cassette tape holder


The auxiliary box is equipped with a cassette tape holder. To use the holder, raise the auxiliary box lid while pushing the lock release button. The plate for the cassette tape holder is detachable.


Cup holders The cup holder is designed for holding cups or drink−cans securely. To use them, observe illustra- tions.


following


the


CAUTION


D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about and possibly injure people in the vehicle during sudden braking or in an accident.


D To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the cup holder closed when it is not in use.


NOTICE


Type A only—As this holder is de- signed for holding soft cups only, do not place too heavy a cup, drink−can or bottle in it.


311


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


To fold down the armrest with the cup holder


To return the armrest with the cup holder to the original position


Type B


Type C


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


Type A


312


’04 TUNDRA_U (L/O 0309)


Type C cup holders are equipped with a detachable adapter for each holder. When you remove the adapter, a bigger cup can be held in the holder.


Type D


Type F


Type E


Type G


313


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


Note pad holder


314


’04 TUNDRA_U (L/O 0309)


Grocery bag/cargo net hooks


Grocery bag hooks


Cargo net hooks


The rear console box is equipped with a note pad holder. This is designed to hold small paper such as note pads. To use the holder, raise the console box upper lid while pushing the lock release button.


CAUTION


D Do not write on the note pad holder


while the vehicle is moving.


D Do not place anything else on the note pad holder. Such items may be in the compartment thrown about and possibly cause injury during sudden braking or an accident.


D To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the console box upper lid closed when it is not in use.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Floor mat


These hooks are designed to hang things like grocery bags or cargo net. Although the cargo net itself is not in- cluded as an original equipment, these hooks can be used to hang the cargo net.


NOTICE


z To prevent damage to the hooks, avoid hanging heavy loads on them when using them as grocery bag hooks.


z To prevent damage


the hook, avoid hanging things other than a cargo net on it when using them as cargo net hooks.


to


Use a floor mat of the correct size. If the floor carpet and floor mat have a hole, then it is designed for use with a locking clip. Fix the floor mat with locking clip into the hole in the floor carpet.


CAUTION


Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.


interferes with


315


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


316


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


SECTION 1− 2


OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Front doors Side doors Access doors Wireless remote control system Power windows Rear side windows Rear window Power rear window Tailgate Hood Toyota vehicle intrusion protection system (TVIP) Theft deterrent system Fuel tank cap Electric moon roof


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


16
16
18
20
21
31
34
34
35
36
38
39
40
42
44


15


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Keys


Front doors (standard and access cab models)


These keys work in every lock. Since the doors can be locked without a key, you should always carry a spare key in case you accidentally lock your key inside the vehicle.


KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system— Both doors lock and unlock simultaneously with either door. In the driver’s door lock, turning the key once will unlock the driv- er’s door and twice in succession will un- lock the driver’s door and passenger’s door simultaneously.


16


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


lock: Push the switch down on the


LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. Both doors lock or unlock simultaneously.


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of locking the doors helps seat belts, prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.


17


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Vehicles with power door lock system— The door will not lock if the key is left in the ignition switch when closing the front doors.


Driver’s side


Passenger’s side


’04 TUNDRA_U (L/O 0309)


Side doors (double cab models)


When all the doors are unlocked simulta- neously using a key, the interior light, igni- tion switch light, step light and cargo lamp will come on and remain on for about 15
seconds before fading out. (For details, see “Center interior and personal lights”, “Ignition switch and step lights” and “Car- go lamp” in Section 1−5.)


the doors


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. All lock and unlock simulta- neously with either front door. In the driv- er’s door lock, turning the key once will unlock the driver’s door and twice in suc- cession will unlock all the doors simulta- neously. This double key turning operation to un- lock all the doors can be changed to a single key turning operation. For details, contact your Toyota dealer.


18


LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


CAUTION


Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.


Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Doors cannot be locked when either front door is open and the key is in the igni- tion.


Driver’s side


Passenger’s side


’04 TUNDRA_U (L/O 0309)


lock: Push the switch down on the


LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. All the doors lock or unlock simultaneous- ly. When the front doors are locked with the inside lock knob, the key or the wireless remote control transmitter, the power door lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control transmitter.


19


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Access doors (access cab models)


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.


to


the


lock


lever


the “LOCK”


REAR DOOR CHILD−PROTECTORS Move position as shown on the label. This feature allows you to lock a rear door so it can be opened from the outside only, not from the inside. We recommend using this feature whenever small children are in the vehicle.


20


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Wireless remote control (standard and access cab models for U.S.A. only)


For easy access to the rear seat, open the access door (rear door). To open: First, open the front door widely. Then pull the outside handle or inside le- ver of the access door. If you try to open the front and rear doors simultaneously, they will not open. To close: First, close completely. Then close the front door. You can open and close the access door only when the front door is widely opened.


the access door


NOTICE


Locking operation


The front door and access door could be damaged if they hit each other when being opened or closed. Be sure to follow the above instructions.


to


THE


AND


UNLOCKING


lock or unlock all


The wireless remote control system is designed the doors or activate the “PANIC” mode from a distance within approximately 1
m (3 ft.) of the vehicle. LOCKING DOORS To lock and unlock all the doors, push the switches slowly and securely. To lock: Push the “LOCK” switch. All the doors are locked simultaneously. At this time one beep will be heard, and the tail lights and lights will flash once. Check to see that the doors are securely locked. If any door is not securely closed, locking cannot be performed by “LOCK” switch and a beep will sound continuously for 5 seconds. However, if the key is in the ignition, a beep will not sound. To stop the beep, close all the doors se- curely or push the “UNLOCK” switch.


front side marker


the


Unlocking operation


21


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


the


lights will


front side marker


“UNLOCK” switch To unlock: Push once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the tail lights and flash twice. When the “UNLOCK” switch is pressed, the interior light, ignition switch light, step light and cargo lamp come on. The lights remain on for about 30 seconds unless any door is opened and closed. You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will be automatically locked again. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again.


22


flashes


intermittently,


“PANIC” SWITCH Pushing the “PANIC” switch blows the horn the head- lights and tail lights, and turns on the interior light. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, push the “PANIC” switch once again, lock or unlock any door with the key or transmitter, or turn the ignition key from the “LOCK” to “ON” position. The “PANIC” mode does not work when the ignition key is in the ignition switch.


to break


WIRELESS REMOTE CONTROL The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage to the transmitter. D Do not leave the transmitter on places the temperature becomes high


where such as on the dashboard.


D Do not disassemble it. D Avoid knocking


it hard against other


objects or dropping it.


D Avoid putting it in water. You can use up to 4 remote keyless entry transmitters for the same vehicle. Contact your Toyota dealer for detailed information. If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.


D The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “REPLACING THE BATTERY”.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci- dent. (See “If you lose your wireless re- mote control transmitter” in Section 4.)


MODEL/FCC ID: BAB237131−056
CAN: 2024 102 1519
MADE IN JAPAN This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


REPLACING THE BATTERY For replacement, use a CR2025 lithium battery or equivalent.


CAUTION


Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.


NOTICE


z When replacing the transmitter bat- tery, be careful not to lose the com- ponents.


z Replace only with


the same or equivalent type recommended by a Toyota dealer.


z Dispose of used batteries according


to the local laws.


Replace the transmitter battery by follow- ing these procedures:


1. Using a coin or equivalent, open the


transmitter case.


23


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


2. Remove the rubber gasket and set it


3. Remove the discharged transmitter bat-


4. Put a new transmitter battery with posi-


aside.


tery.


tive (+) side up.


NOTICE


Do not bend the terminals.


24


the


Place transmitter. Then close case securely.


rubber gasket back on


the transmitter


the


NOTICE


z Make sure


the positive side and negative side of the transmitter bat- tery are faced correctly.


z Do not replace the battery with wet hands. Water may cause unexpected rust.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Wireless remote control (double cab models)


z Do not touch or move any compo- nents inside of the transmitter, or it may interfere with proper opera- tion.


z Be careful not to bend the electrode of the transmitter battery insertion and that dust or oils do not adhere to the transmitter case.


z Close the transmitter case securely.


After replacing the battery, check that the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.


Locking operation


to


THE


AND


UNLOCKING


lock or unlock all


The wireless remote control system is designed the doors or activate the “PANIC” mode from a distance within approximately 1
m (3 ft.) of the vehicle. LOCKING DOORS To lock and unlock all the doors, push the switches slowly and securely. To lock: Push the “LOCK” switch. All the doors are locked simultaneously. At this time one beep will be heard, and the parking lights and tail lights flash once. Check to see that all the doors are se- curely locked. If any of the doors is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound con- tinuously for 10 seconds. However, if the key is in the ignition, a beep will not sound. To stop the beep, close all the doors se- curely or push the “UNLOCK” switch. The beep can be disabled. For details, contact your Toyota dealer.


Unlocking operation


25


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Check the beep ON/OFF operation by pushing the transmitter switch after you finish this procedure. If the beep does not operate as expected, repeat this proce- dure from step 1.


the


“UNLOCK” switch To unlock: Push once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the doors simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights and tail lights flash twice. This double switch operation to unlock all the doors can be changed to a single switch operation. For details, contact your Toyota dealer. When all the doors are unlocked simulta- neously with a wireless remote control ignition interior transmitter, light, switch light and cargo lamp come on for about 15 seconds and then fade out, even if the door is not opened. (For details, see “Center interior and per- sonal “Ignition switch and step lights” and “Cargo lamp” in Section 1−5.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the doors will be automatically locked again.


light, step


lights”,


the


for


timing


the automatic door


The lock function can be changed. For details, con- tact your Toyota dealer. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again. locking or unlocking The wireless door function can be erased. For details, con- tact your Toyota dealer. SWITCHING BEEP SOUND ON AND OFF You can switch the beep on and off. (The beep is on initially and after battery re- placement.) To switch the beep on and off: With the driver’s door opened— 1. Insert the ignition key and remove it. 2. Within 5 seconds,


ignition key again and turn it to the “ON” posi- tion.


insert


the


3. After 10 seconds, push


the same “LOCK”, “UNLOCK” or “PANIC” switch twice within 10 seconds. Two beep sounds inform you that the program has been switched on or off. If this procedure is not followed exactly, the beep will not operate as expected.


26


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


REMOTE


The “PANIC” mode does not work when the ignition key is in the “ON” position. This alarm function can be disabled. For details, contact your Toyota dealer. WIRELESS TRANSMITTER The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage to the transmitter. D Do not leave the transmitter on places the temperature becomes high


where such as on the dashboard.


CONTROL


D Do not disassemble it. D Avoid knocking


it hard against other


objects or dropping it.


D Avoid putting it in water. You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information.


transmitters


for


If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: D Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.


D The battery may have been consumed. Check the battery in the transmitter. To replace see following “REPLACING THE BATTERY”.


the battery,


If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci- dent. (See “If you lose your wireless re- mote control transmitter” in Section 4.)


27


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


flashes


“PANIC” SWITCH Pushing the “PANIC” switch blows the horn intermittently and the headlights and tail lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, do the following: D Push any of the switches on the wire-


to break


less remote control transmitter.


D Unlock any of the doors with the key. D Turn the ignition key from the “LOCK”


to the “ON” position.


’04 TUNDRA_U (L/O 0309)


For vehicles sold in U.S.A.


This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


interference


NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures:


to radio or


D Reorient or relocate the receiving an-


tenna.


D Increase the separation between the


equipment and receiver.


D Connect the equipment into an outlet to


on a circuit different which the receiver is connected.


from


that


D Consult the dealer or an experienced


radio / TV technician for help.


FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.


28


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


For vehicles sold in Canada


Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.


interference,


including


’04 TUNDRA_U (L/O 0309)


REPLACING THE BATTERY For replacement, use a CR2016 lithium battery or equivalent.


CAUTION


Special care should be taken to pre- vent small children from swallowing the removed battery or components.


NOTICE


z When replacing the transmitter bat- tery, be careful not to lose the com- ponents.


z Replace only with


the same or equivalent type recommended by a Toyota dealer.


z Dispose of used batteries according


to the local laws.


Replace procedures:


the battery by


following


these


1. Using a coin or equivalent, open the


transmitter case.


29


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


z Be careful not to bend the electrode of the transmitter battery insertion and that dust or oils do not adhere to the transmitter case.


z Close the transmitter case securely.


After replacing the battery, check that the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.


2. Remove the discharged transmitter bat-


3. Put a new transmitter battery with posi-


tery.


NOTICE


Do not bend the terminals.


30


tive (+) side up.


Close the transmitter case securely.


NOTICE


z Make sure


the positive side and negative side of the transmitter bat- tery are faced correctly.


z Do not replace the battery with wet hands. Water may cause unexpected rust.


z Do not touch or move any compo- nents inside of the transmitter, or it may interfere with proper opera- tion.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Power windows


Standard and access cab models


The windows can be operated with the switch on either front door (standard and access cab models)/each door (double cab models). The power windows work when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Pull up the switch.


front door


Standard and access cab models


Double cab models


Double cab models


31


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Automatic operation (to open only): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.


32


Standard and access cab models


Double cab models


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


THE


(double


PASSENGERS’


OPERATING WINDOW Use the switches on the passenger’s door (standard and access cab mod- els)/passengers’ doors cab models) or the switch on the driver’s door that controls each passenger’s window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passenger’s (stan- dard and access cab models)/ passengers’ (double cab models) window and power rear window cannot be operated.


Window lock switch


Driver’s door switch (standard and access cab models)


Window lock switch


Driver’s door switches (double cab mod- els)


CAUTION


To avoid serious personal injury, you must do the following. D Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get it caught could result injury. When anyone closes the power win- dows, make sure he or she oper- ates the windows safely.


in a closing window,


in a serious


the vehicle.


inside


D When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.


them


33


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Rear side windows (access cab models)


Rear window


D Be sure to remove the ignition key


when you leave your vehicle.


D Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.


trapped


To open the rear side window, pull the latch handle toward you and swing it fully out. After closing the window, make sure it is completely closed.


To open the rear window, push the le- ver and slide the window. After closing the window, make sure it is completely closed.


34


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


Power rear window


Access cab models


’04 TUNDRA_U (L/O 0309)


The rear window can be operated with the switch on the instrument panel. The ignition key must be in the “ON” posi- tion. Key off operation: If both front doors are closed, they work 43 seconds even after the ignition switch is turned off. The pow- er rear window stops working when either front door is opened. The rear window moves as long as you hold the switch.


Standard and access cab models


” ”


To open: Push the switch on the “ (standard and access cab models) or “ (double cab models) side. To close: Push the switch on the “ (standard and access cab models) or “ (double cab models) side. Double cab models only—At this time, the window will stop partway. Push the switch again to fully close the window.


” ”


Double cab models


Double cab models


35


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


If you push in the window lock switch on the driver’s door, the rear window cannot be operated.


CAUTION


To avoid serious personal injury, you must do the following. D Before you close the power rear window, always make sure there is nobody around the power rear win- dow. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it injury. could result When anyone closes the power rear window, make sure he or she oper- ates the window safely.


in a closing window,


in a serious


the vehicle.


inside


D When small children are in the ve- hicle, never let them use the power rear window switch without supervi- sion.


D Be sure to remove the ignition key


when you leave your vehicle.


36


’04 TUNDRA_U (L/O 0309)


Tailgate


D Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power back window switch and get trapped in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.


D Keep the rear window closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.


OPENING To open the tailgate, pull the handle up. The support cables will hold the tailgate horizontal. See “—Stowage precautions” in Section 2
for precautions when loading luggage. After closing the tailgate, try pulling and pushing is securely closed.


to make sure it


it


NOTICE


Avoid driving with the tailgate open.


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Support cable bracket


REMOVAL 1. Open the tailgate to the angle where you can release the brackets on the support cables lugs on both sides.


from


the


To release the support cable bracket, lift it up and slide it off.


2. Tilt the tailgate to about 30° from vertical and pull up the right side of the tailgate to unhook the right side.


3. Slide the tailgate a little to the right


to unhook the left side.


To attach the tailgate, follow the removal procedure in reverse order. After closing the tailgate, try pulling it to- ward you is securely closed. We closed when not in use.


recommend you keep


to make sure


tailgate


the


it


NOTICE


Make sure the support brackets are securely latched on both side panels when installing the tailgate.


37


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Hood


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it to lock or unlock the tailgate. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise.


To open the hood: 1. Pull the hood lock release lever. The


hood will spring up slightly.


CAUTION


Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.


38


2. In front of the vehicle, pull up the the


lever and


lift


auxiliary catch hood.


Before closing the hood, check to see that you have not forgotten any tools, rags, etc. Then lower the hood and make sure it If necessary, press down gently on the front edge to lock it.


into place.


locks


2004 TUNDRA from Sep. ’03 Prod. (OM34426U)


’04 TUNDRA_U (L/O 0309)


Toyota vehicle intrusion protection system (TVIP) (standard and access cab models for U.S.A. only)


is a


theft deterrent system.


TVIP If someone attempts to damage or break into your vehicle, the system sounds the alarm while flashing the lights.


SETTING THE SYSTEM You can set the system as follows. 1. Remove


the key


from


the


ignition


switch.


2. Have all passengers get out of


the


vehicle.


3. Close all the doors securely. 4. Lock all the doors with the key or re- mote keyless entry transmitter. At this time, light comes on. The system will be set in 30 seconds. When the system is set, the indicator light will start to flash.


the TVIP


indicator


5. Make sure


light flashes. Then you may leave the ve- hicle.


indicator


that


the


Never leave anyone in the vehicle when you set the system because unlocking from the inside activates the alarm. Activating the alarm If the system detects a threat to the intermittently vehicle, blows the horn for one minute while flashing head- lights, tail lights and front side marker lights, and turns on the interior light. The system detects a threat under any of the following conditions: D Either of the front doors is unlocked by means other than the key or remote keyless entry transmitter. If the key is not in the ignition switch, all the doors will be automatically locked again.


D Any door is forcibly opened. D The side windows are tapped or bro-


ken.


D The battery


terminal and then reconnected.


is disconnected


D The ignition is hotwired.


39


Loading...
x