Download PDF Manual

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


10
10
12
12
14
14
15
16
17


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Front doors


Keys This key works in every lock. Since the doors can be locked without a key, you should always carry a spare key in case you accidentally lock your key inside the vehicle.


KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend you to write down the key number and keep it in safe place.


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system— Both doors lock and unlock simultaneously with either door. In the driver’s door lock, turning the key once will unlock the driv- er’s door and twice in succession will un- lock the driver’s door and passenger’s door simultaneously.


10


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. Both doors lock or unlock simultaneously.


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of locking the doors helps seat belts, prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.


Driver’s side


LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Vehicles with power door lock system— The door will not lock if the key is left in the ignition switch when closing the front doors.


Passenger’s side


2002 MY TUNDRA_U (OM34417U)


11


’02 TUNDRA_U (L/O 0108)


Access doors


Power windows


For easy access to the rear seat, open the access door (rear door). To open: First, open the front door widely. Then pull the outside handle or inside le- ver of the access door. If you try to open the front and rear doors simultaneously, they will not open. To close: First, close completely. Then close the front door. You can open and close the access door only when the front door is widely opened.


the access door


NOTICE


The front door and access door could be damaged if they hit each other when being opened or closed. Be sure to follow the above instructions.


The windows can be operated with the switch on either front door. The power windows work when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when either is opened. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Pull up the switch.


front door


12


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


THE


PASSENGER’S


OPERATING WINDOW Use the switch on the passenger’s door or the switch on the driver’s door that controls the passenger’s window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passenger’s window cannot be operated.


Automatic operation (to open only): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.


Window lock switch


2002 MY TUNDRA_U (OM34417U)


13


’02 TUNDRA_U (L/O 0108)


Rear side windows (access cab models)


Rear window


To open the rear side window, pull the latch handle toward you and swing it fully out. After closing the window, make sure it is completely closed.


To open the rear window, push the le- ver and slide the window. After closing the window, make sure it is completely closed.


CAUTION


To avoid serious personal injury, you must do the following. (cid:1) Always make sure the heads, hands and other parts of the bodies of all occupants are kept completely in- side the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, make sure that he/she operates the win- dows safely.


(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.


them


(cid:1) Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power window switches and get in a window. Unat- tended children can be involved in serious accidents.


trapped


14


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Tailgate


Support cable bracket


OPENING To open the tailgate, pull the handle up. The support cables will hold the tailgate horizontal. See in Section 2 for precautions in loading lug- gage. After closing the tailgate, try pulling and pushing is securely closed.


“Luggage stowage precautions”


to make sure it


it


REMOVAL 1. Open the tailgate to the angle where you can release the brackets on the support cables lugs on both sides.


from


the


To release the support cable bracket, lift it up and slide it off.


2. Tilt the tailgate to about 30° from vertical and pull up the right side of the tailgate to unhook the right side.


NOTICE


Avoid driving with the tailgate open.


2002 MY TUNDRA_U (OM34417U)


15


’02 TUNDRA_U (L/O 0108)


Hood


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it to lock or unlock the tailgate. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise.


To open the hood: 1. Pull the hood lock release lever. The


hood will spring up slightly.


CAUTION


Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.


3. Slide the tailgate a little to the right


to unhook the left side.


To attach the tailgate, follow the removal procedure in reverse order. After closing the tailgate, try pulling it to- ward you is securely closed. We closed when not in use.


recommend you keep


to make sure


tailgate


the


it


NOTICE


Make sure the support brackets are securely latched on both side panels when installing the tailgate.


16


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Fuel tank cap


This indicates that the fuel filler door is on the left side of your vehicle.


Without tachometer


With tachometer


2002 MY TUNDRA_U (OM34417U)


17


2. In front of the vehicle, pull up the the


lever and


lift


auxiliary catch hood.


Before closing the hood, check to see that you have not forgotten any tools, rags, etc. Then lower the hood and make sure it If necessary, press down gently on the front edge to lock it.


into place.


locks


’02 TUNDRA_U (L/O 0108)


truck bed


(cid:1) Do not fill a fuel container on a plastic liner, a rubber truck bed mat, or any other insulat- ing material. A static electricity charge could cause a spark and fire hazard. The proper procedure is to place an approved fuel container on the ground away from the truck for filling.


2. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it. After removing the cap, hang it on the cap hanger.


the cap clockwise


It is not unusual to hear a slight swoosh when the cap is opened. When installing, turn till you hear a click. If the cap is not tightened securely, the malfunction lamp comes on. Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


indicator


1. To open the fuel filler door, insert the key and turn it counterclockwise. When refueling, turn off the engine.


CAUTION


(cid:1) Do not smoke, cause sparks or al- flames when refueling.


low open The fumes are flammable.


(cid:1) When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.


the cap


if


18


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) Make sure the cap is tightened se- in


curely to prevent fuel spillage case of an accident.


(cid:1) Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.


2002 MY TUNDRA_U (OM34417U)


19


’02 TUNDRA_U (L/O 0108)


20


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


SECTION 1– 3


OPERATION OF INSTRUMENTS AND CONTROLS Seats, Seat belts, Steering wheel and Mirrors Seats Front seats Armrest Swing–up rear seats Head restraints Seat belts SRS driver and front passenger airbags Passenger airbag manual on–off switch Child restraint Tilt steering wheel Outside rear view mirrors Anti–glare inside rear view mirroror Sun visors


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


22
22
26
27
28
29
38
47
48
74
75
76
77


2002 MY TUNDRA_U (OM34417U)


21


’02 TUNDRA_U (L/O 0108)


Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.


Front seats— —Seat adjustment precautions Adjust the driver’s seat so that the foot pedals, steering wheel and instrument panel controls are within easy reach of the driver.


CAUTION


CAUTION


(cid:1) While adjusting the seat, do not put your hands under the seat or near the moving parts. You may catch and injure your hands or fingers.


in


(cid:1) Do not drive the vehicle unless the occupants are properly seated. Do top of a not allow sitting on folded–down seatback, or the luggage compartment or cargo area. Persons not properly seated and/or properly restrained by seat belts can be severely injured in the event of emergency braking or a collision. (cid:1) During driving, do not allow pas- to stand up or move sengers around between seats. Severe inju- ries can occur in the event of emer- gency braking or a collision.


(cid:1) Adjustments should not be made while the vehicle is moving, as the seat may unexpectedly move and cause the driver to lose control of the vehicle.


(cid:1) When adjusting the seat, be careful that the seat does not hit a passen- ger or luggage.


(cid:1) After adjusting the seat position, try sliding it forward and backward to make sure it is locked in posi- tion.


(cid:1) After adjusting the seatback, exert body pressure to make sure it is locked in position.


(cid:1) Do not put objects under the seats. The objects may interfere with the seat–lock mechanism or unexpect- edly push up the seat position ad- justing lever; the seat may suddenly move, causing the driver to lose control of the vehicle.


22


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


—Adjusting front seats (manual seat)


1. SEAT POSITION ADJUSTING LEVER Separate and split bench seat: Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. Non–split bench seat: Pull the lever up. Then slide the seat to the desired posi- tion with slight body pressure and re- lease the lever. 2. DRIVER’S SEAT CUSHION ANGLE


ADJUSTING KNOB


Turn the knob either way. 3. SEATBACK ANGLE


LEVER


ADJUSTING


lever up. lean back to the desired angle


Lean forward and pull the Then and release the lever.


Separate and split bench seat


Non–split bench seat


2002 MY TUNDRA_U (OM34417U)


23


’02 TUNDRA_U (L/O 0108)


—Adjusting front seats (power seats)


1. SEAT POSITION AND SEAT CUSHION


HEIGHT ADJUSTING SWITCH


Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under seats. interfere with movement. 2. SEATBACK


the front the seat


ADJUSTING


It might


ANGLE


SWITCH


Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position.


CAUTION


To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the driver and the pas- senger are sitting up straight and well back If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seat- back.


in the seats.


24


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


—Tilting passenger’s seatback for rear seat entry (access cab models)


CAUTION


(cid:1) After putting back the seatback, try pushing the seatback forward and rearward to make sure it is secured in place.


(cid:1) Never allow anyone to rest their foot on the press pedal while the vehicle is moving.


CAUTION


To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the driver and the pas- senger are sitting up straight and well back If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seat- back.


in the seats.


3. SEAT


LUMBAR ADJUSTING SWITCH


SUPPORT


Push the control switch on either way. The amount of lumbar support will change as long as the switch is pushed.


For easy access to the rear seat, do this. Lift the seatback angle adjusting lever or press the pedal behind the seatback. The seatback will tilt forward. After passengers are in, lift up the seat- back until it locks.


2002 MY TUNDRA_U (OM34417U)


25


’02 TUNDRA_U (L/O 0108)


—Folding seatback (non–split bench seat)


Armrest


CAUTION


When returning the seatback to the upright position, observe the follow- ing precautions in order to prevent personal injury in a collision or sud- den stop: (cid:1) Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.


(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.


Pull the seatback lock release lever and fold down the seatback. Hold the lever until you have swung the seatback forward slightly.


26


2002 MY TUNDRA_U (OM34417U)


Type A


’02 TUNDRA_U (L/O 0108)


Swing–up rear seats (access cab models)


To use the armrest, do this. Type A— To lower: Pull the lock release strap and down the armrest. To raise: Push down the lock release knob and up the armrest. Type B—Pull the armrest down as shown in the illustration. Type C—Pull the armrest out as shown in the illustration.


NOTICE


To prevent damage to the armrest, avoid putting heavy loads on it.


1. Stow the rear seat belt and buckles


as shown in the illustration.


This prevents the belt and buckles from falling out when you swing up the rear seat.


NOTICE


The seat belt and buckles must be stowed before you swing up the rear seat.


2002 MY TUNDRA_U (OM34417U)


27


Type B


Type C


’02 TUNDRA_U (L/O 0108)


Head restraints


CAUTION


When returning the bottom cushion to its original position, observe the fol- lowing precautions in order to pre- vent personal injury in a collision or sudden stop: (cid:1) Make sure the bottom cushion is securely locked by trying to pull up the edge of the bottom cushion. Failure to do so will prevent the seat belt from operating properly.


(cid:1) Make sure the seat belts are not twisted or caught under the bottom cushion and are arranged in their proper position and are ready to use.


Front


Rear


2. Raise


the bottom cushion while


pushing the lock release lever.


28


2002 MY TUNDRA_U (OM34417U)


For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.


CAUTION


(cid:1) Adjust the center of the head re- straint so that it is closest to the top of your ears.


(cid:1) After adjusting the head restraint, make sure it is locked in position. the head re-


(cid:1) Do not drive with


straints removed.


’02 TUNDRA_U (L/O 0108)


Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” for details. STANDARD CAB MODELS— If a child is too large for a child restraint system, the child should sit in the seat and must be restrained using the vehicle’s seat belt. ACCESS CAB MODELS— If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.


2002 MY TUNDRA_U (OM34417U)


Do not allow the child to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. It does not provide sufficient restraint. in a Small–framed person or youth 3–point type seat belt. On models with a non–split bench seat, have a small– framed person or youth sit slightly closer to the center of the vehicle (so the shoul- der belt does not cross over the neck). On models with separate seats and a split bench seat, move the seat fully backward. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.


recommendations. The


29


’02 TUNDRA_U (L/O 0108)


—Front outside seat belts and rear outside seat belts


(cid:1) Keep the belts clean and dry.


If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers—they may severely weaken the belts. (See “Cleaning the interior” in Section 5.)


(cid:1) Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.


Adjust the seat as needed (front seats only) and sit up straight and well back in the seat. To fasten your belt, pull it out of the retractor and insert the tab into the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.


CAUTION


the vehicle


in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: (cid:1) Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. (cid:1) Avoid reclining the seatbacks too much. The seat belts provide maxi- mum protection when the seatbacks are in the upright position. (Refer to the seat adjustment instructions.) (cid:1) Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or side doors.


(cid:1) Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.


30


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. Standard cab models— To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. Access cab models— To raise: Slide the anchor up. To lower: Pull the lock release knob and slide the anchor down. After adjustment, make sure the anchor is locked in position.


CAUTION


Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause severe injuries in a collision.


If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor. When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” in this section.) To free the belt again, fully retract the belt and then pull the belt out once more.


then


is


CAUTION


Standard cab models


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


Access cab models


2002 MY TUNDRA_U (OM34417U)


31


’02 TUNDRA_U (L/O 0108)


Take up slack


Too high


Keep as low on hips as possible


CAUTION


(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.


(cid:1) For your safety, do not place the


shoulder belt under your arm.


the


lap and


the position of


Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.


To release the belt, press the buckle–re- lease button and allow the belt to re- tract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.


32


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


—Front center seat belt and rear center seat belt


Lengthen


CAUTION


Too high


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


Sit up straight and well back in the seat. To fasten your belt, insert the tab into the buckle. You will hear a click when the tab locks into the buckle. If the belt is not long enough for you, hold the tab at a right angle to the belt and pull on the tab.


Adjust to a snug fit


Keep as low on hips as possible


Remove excess length of the belt and adjust the belt position. To shorten the belt, pull the free end of the belt. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit.


CAUTION


Both high–positioned and loose–fit- ting lap belts could cause serious in- juries due to sliding under the lap belt during a collision or other unin- tended result. Keep the lap belt posi- tioned as low on hips as possible.


2002 MY TUNDRA_U (OM34417U)


33


’02 TUNDRA_U (L/O 0108)


—Stowing the rear seat belt and buckles (access cab models)


To release the belt, press the buckle–re- lease button.


The rear seat belt and buckles can be stowed when not in use. Seat belt and buckles must be stowed before you swing up the bottom cushion. (See “Swing–up rear seats” in this sec- tion.)


34


2002 MY TUNDRA_U (OM34417U)


from your Toyota dealer


—Seat belt extender If your seat belt cannot be fastened se- curely because it is not long enough, a personalized seat belt extender is avail- able free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender. Bring the heaviest coat you expect to wear for prop- er measurement and selection of length. Additional ordering information is available at your Toyota dealer.


CAUTION


the


When using the seat belt extender, following precautions. observe Failure to follow these instructions could result in less effectiveness of the seat belt restraint system in case of vehicle accident, the chance of personal injury. (cid:1) Never use the seat belt extender if you can fasten the seat belt without it.


increasing


(cid:1) Remember that the extender pro- vided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one origi- nally intended for.


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the seat belt extender is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the “PRESS” signs on the buckle–release buttons of the ex- tender and the seat belt are both facing outward as shown. You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle–release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extend- er itself. When not and store in the vehicle for future use.


in use, remove the extender


2002 MY TUNDRA_U (OM34417U)


35


’02 TUNDRA_U (L/O 0108)


—Front seat belt pretensioners


The driver and front passenger’s seat belt pretensioners are designed to be activated in response to a severe fron- tal impact. When the airbag sensor detects the shock of a severe frontal impact, the front seat belts are quickly drawn back in by the retractors so that the belts snugly restrain the front seat occupants. The front seat belt pretensioners are acti- vated even with no passenger in the front seat. Collisions occurring at certain speeds and angles may cause the seat belt preten- sioners and SRS airbags not to operate all together.


This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the front seat belt pretensioners are operating proper- ly. This warning the airbag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. (For details, see “Service reminder indicators and warning buzzers” in Section 1–5.)


light system monitors


The front seat belt pretensioner system mainly consists of the following compo- nents and their locations are shown in the illustration. 1. Front airbag sensors 2. SRS warning light 3. Front seat belt pretensioner assemblies 4. Airbag sensor assembly The front seat belt pretensioners are con- trolled by the airbag sensor assembly. The airbag sensor assembly consists of a saf- ing sensor and airbag sensor.


36


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


When the front seat belt pretensioners are activated, an operating noise may be heard and a small amount of smoke–like gas may be released. This gas is harm- less and does not indicate that a fire is occurring. Once front seat belt pretensioners the have been activated, the seat belt retrac- tors remain locked.


CAUTION


Do not modify, remove, strike or open the front seat belt pretensioner as- semblies, airbag sensor or surround- ing area or wiring. Doing any of these may cause sudden operation of the front seat belt pretensioners or disable the system, which could re- sult in death or serious injury. Failure to follow these instructions can result in death or serious inju- ries.


NOTICE


Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the front seat belt pretensioners in some cases. (cid:2) Installation of electronic devices such as a mobile two–way radio, cassette tape player or compact disc player


(cid:2) Repairs on or near the front seat


belt pretensioner assemblies


(cid:2) Modification of the suspension sys-


tem


(cid:2) Modification of the front end struc-


ture


(cid:2) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


(cid:2) Repairs made on or near the front fenders, front end structure or con- sole


2002 MY TUNDRA_U (OM34417U)


following


conditions occurs,


This front seat belt pretensioner system has a service reminder indicator to inform the driver of operating problems. If any of the this indicates a malfunction of the airbags or pretensioners. Contact your Toyota dealer as soon as possible the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while


to service


driving.


(cid:1) If either front seat belt does not retract or cannot be pulled out due to a mal- function or activation of the relevant front seat belt pretensioner.


37


’02 TUNDRA_U (L/O 0108)


SRS driver and front passenger airbags


In response to a severe frontal impact, the SRS airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS airbags help to reduce inju- ries mainly to the driver’s or right front passenger’s head or chest caused by di- rectly hitting the steering wheel or dash- board. The front passenger airbag is acti- vated even with no passenger in the front seat. Be sure to wear your seat belt properly. Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and right front pas- senger when the SRS airbags are inflated.


The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide further protection for the driver and right front passenger in addition to the primary safety protection provided by the seat belts. (cid:1) Vehicles with separate front seats—The SRS airbags are designed to protect the driver and front passenger.


(cid:1) Vehicles with bench type front seats— The SRS airbags are designed to pro- tect the driver and right–front passen- ger. They are not designed to protect occupant in the center position.


In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the front seat belt pretensioners to operate.


(cid:1) Either front seat belt pretensioner as- sembly is scratched, cracked, or otherwise dam- aged.


surrounding


area


or


38


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


The driver or front passengers who are too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. To- yota strongly recommends that: (cid:1) The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle. (cid:1) The


far back as possible from the dash- board.


front passengers sit as


(cid:1) All vehicle occupants be properly restrained using the available seat belts.


CAUTION


(cid:1) Make sure that the indicator light is


off.


(cid:1) Do not turn off the passenger air- bag manual on–off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the right front passenger seating position.


(cid:1) When the passenger airbag manual on–off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.


Indicator light


airbag


system


passenger


The is equipped with a manual on–off switch and indicator light. Turning the passen- ger airbag manual on–off switch clock- wise to the “ON” position makes the passenger airbag system operational. Turning the passenger airbag manual on–off switch counterclockwise to the “OFF” position disables the passenger airbag system. The indicator light on the passenger airbag manual on–off switch will come on when the passen- ger airbag system has been disabled. See switch” in this section for detail.


“Passenger airbag manual on–off


2002 MY TUNDRA_U (OM34417U)


39


’02 TUNDRA_U (L/O 0108)


TABLE 1: A PASSENGER RISK GROUP


Infant. An infant (less than 1 year old) who must ride in the front seat because: (cid:1) Vehicle has no rear seat; (cid:1) Vehicle has a rear seat too small to accommodate a rear–facing infant seat;


or


(cid:1) The infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can constantly monitor the child’s condition.


Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: (cid:1) Vehicle has no rear seat: (cid:1) Although children ages 1 to 12 ride in the rear seat(s) whenever possible,


children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of vehicle; or


(cid:1) The child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.


Medical condition. A passenger has a medical condition which according to his or her physician: (cid:1) Causes the passenger airbag to pose a special risk for the passenger: and (cid:1) Makes the potential harm from the passenger airbag in a crash greater than the potential harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard, or windshield in a crash.


For more detailed information concerning about the passenger risk group, please contact NHTSA at 1–800–424–9393 or Transport Canada at 1–800–333–0371.


40


2002 MY TUNDRA_U (OM34417U)


This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” in Section 1–5.)


light system monitors


reminder


“Service


’02 TUNDRA_U (L/O 0108)


this


However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the nose of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It is possible that in some collisions at the lower zone of airbag sensor detection and activation the SRS airbags and seat belt pretensioners will not operate all together. For the safety of all occupants, always wear your seat belts properly.


Collision from the rear


Collision from the side


Vehicle rollover


The SRS airbags are not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low–speed frontal collision.


2002 MY TUNDRA_U (OM34417U)


41


The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when impacting straight into a fixed barrier that does not move or deform. If the severity of the impact is below the above threshold the SRS airbags may not deploy.


level,


’02 TUNDRA_U (L/O 0108)


Hitting a curb, edge of pavement or hard material


Falling into or jumping over a deep hole


Landing hard or vehicle falling


The SRS airbags may deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


In a severe frontal impact, the sensors detect deceleration and the system trig- gers the airbag inflators. Then a chemical reaction in the inflators quickly fills the airbags with non–toxic gas to help restrain the forward motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non–toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.


The SRS airbag system consists mainly of the following components, and their loca- tions are shown in the illustration. 1. Front airbag sensors 2. SRS warning light 3. Airbag module for right front passenger


(airbag and inflator)


4. Passenger airbag manual on–off switch 5. Airbag sensor assembly 6. Airbag module for driver


(airbag and inflator)


The airbag sensor assembly consists of a safing sensor and airbag sensor.


42


2002 MY TUNDRA_U (OM34417U)


the windshield as


A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.


’02 TUNDRA_U (L/O 0108)


(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child restraint system. As to access cab models, Toyota recommends that all infants and children be placed in the rear seat of the ve- hicle and properly restrained. The rear seat is the safest for infants and children. For instructions con- cerning the installation of a child restraint system, see “Child re- straint” in this section.


CAUTION


(cid:1) The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and right front passenger side seat belt systems. The front seat occupants can be killed or seriously injured by the inflating airbags if they do not wear the available seat belts prop- erly. During sudden braking just be- fore a collision, an unrestrained driver or front passenger can move forward into direct contact with or close proximity to the airbag which may then deploy during the colli- sion. To ensure maximum protection in an accident, the driver and all passengers the vehicle must wear their seat belts properly. Wear- ing a seat belt properly during an the chances of accident reduces death or serious injury or being thrown out of the vehicle. For instructions and precautions con- cerning the seat belt system, see “Seat belts” in this section.


in


2002 MY TUNDRA_U (OM34417U)


43


’02 TUNDRA_U (L/O 0108)


CAUTION


A member of a passenger risk group should never sit or be occupied in the right front passenger seat with airbag manual on–off switch in the “ON” position. (For details, see “SRS driver and front passenger airbags” in this section.)


(cid:1) A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. For the installation of a child restraint sys- tem, see “Child restraint” in this section.


instructions concerning


CAUTION


(cid:1) Never put a rear–facing child re- straint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an acci- dent, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child.


44


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


(cid:1) Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or serious- ly injured. Sit up straight and well back in the seat, and always use your seat belt properly.


(cid:1) Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag inflates with con- siderable speed and force; the child may be killed or seriously injured. (cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” in this section.


(cid:1) Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the airbag system. They might restrict inflation or cause death or serious injury as they are projected rear- ward by the force of deploying air- bags. Likewise, the driver and front passenger should not hold things in their arms or on their knees.


2002 MY TUNDRA_U (OM34417U)


45


’02 TUNDRA_U (L/O 0108)


(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS airbag inflation or disable the system, which could result in death or serious injury. instructions Failure to follow these can result in death or serious injury.


NOTICE


Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. (cid:2) Installation of electronic devices such as a mobile two–way radio, cassette tape player or compact disc player


(cid:2) Modification of the suspension sys-


tem


(cid:2) Modification of the front end struc-


ture


(cid:2) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


(cid:2) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag


46


2002 MY TUNDRA_U (OM34417U)


this


This SRS airbag system has a service reminder indicator to inform the driver of operating problems. If either of the follow- ing conditions occurs, indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while


driving.


’02 TUNDRA_U (L/O 0108)


Passenger airbag manual on–off switch


Indicator light


This on–off switch is designed to dis- able the passenger airbag in order to allow usage, if necessary, of a member of a passenger risk group identified in TABLE 1 is occupying the right front passenger seating position. (For details, see “SRS driver and front passenger airbags” in this section.) Operate on–off switch as follows: Insert key into the keyhole and turn it. To turn passenger airbag on: Turn the key clockwise to the “ON” position. To turn passenger airbag off: Turn the key counterclockwise to the “OFF” position. The indicator comes on when the passen- ger airbag system is off.


2002 MY TUNDRA_U (OM34417U)


CAUTION


(cid:1) Make sure that the indicator light is


off.


(cid:1) Do not turn off the passenger air- bag manual on–off switch except when a member of a passenger risk group identified in TABLE 1 (page 40) is occupying the right front pas- senger seating position.


(cid:1) When the passenger airbag manual on–off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.


For details, see “SRS driver and front passenger airbags” in this section.


47


In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS airbags have been inflated. (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS airbags to inflate.


front


(cid:1) The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.


passenger


airbag


NOTICE


Do not disconnect the battery cables before contacting your Toyota dealer.


’02 TUNDRA_U (L/O 0108)


(cid:1) Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.


child


the


by


Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the seat and must be restrained using the vehicle’s seat belt. See “Seat belts” for details.


CAUTION


(cid:1) For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.


(cid:1) STANDARD CAB MODELS—


Toyota strongly urges use of a proper child restraint system which conforms to the size of the child. ACCESS CAB MODELS— Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.)


force of


the


48


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


When not using the child restraint system, keep it secured with the seat belt or place it somewhere other the passenger compartment. This will prevent it from in- juring passengers in the event of a sud- den stop or accident.


than


the manufacturer’s


—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with either the lap belt or the lap portion of the lap/ shoulder belt. You must carefully con- sult instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. The child restraint system should be installed on the rear seat if your vehicle is equipped with rear seats. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.


CAUTION


the


force of


(cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.) installing the child restraint system, make sure it is secured in place according to the manufactur- er’s is not re- instructions. strained securely, it may cause death or serious injury to the child in the event of a sudden stop or accident.


(cid:1) After


If


it


2002 MY TUNDRA_U (OM34417U)


49


’02 TUNDRA_U (L/O 0108)


—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchors for securing the top strap of a child restraint system. For instructions on how to use the anchor bracket, see “—Using a top strap” in this section.


(A) Infant seat


(C) Booster seat


50


2002 MY TUNDRA_U (OM34417U)


(B) Convertible seat


’02 TUNDRA_U (L/O 0108)


—Installation with 2–point type seat belt


(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.


With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion.


the child restraint system


CAUTION


Ignoring the above instructions may result in a serious injury in case of an accident.


CAUTION


airbag manual


Never put a rear–facing child restraint system on the front seat with the passenger on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.


2002 MY TUNDRA_U (OM34417U)


51


’02 TUNDRA_U (L/O 0108)


CAUTION


If you must put a rear–facing child restraint system on the front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.


When you put a rear–facing child re- straint system on the front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.


CAUTION


(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause death or seri- ous injury to the child and front passenger in case of sudden brak- ing or a collision.


(cid:1) If your driving position is not satis- the child restraint


factory, system at another position.


install


52


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


2. While pressing the infant seat


firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.


2002 MY TUNDRA_U (OM34417U)


53


1. Run


the


lap belt


the center


infant seat


through or around the instructions provided by its manufactur-

Loading...
x