Download PDF Manual

in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.


3. While pressing


the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


2002 MY TUNDRA_U (OM34417U)


65


’02 TUNDRA_U (L/O 0108)


CAUTION


A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)


4. To remove the convertible seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward–fac- ing position only.


66


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


CAUTION


(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.


to do so could reduce


(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.


(cid:1) For child’s safety, do not place the


shoulder belt under child’s arm.


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.


2002 MY TUNDRA_U (OM34417U)


67


1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.


insert


the


tab


Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.


’02 TUNDRA_U (L/O 0108)


—Using a top strap (standard cab models)


Symbol


Symbol


Anchor bracket


Separate seat


Anchor brackets


Bench seat


2. To remove the child restraint system, press the buckle–release button and al- low the belt to retract.


Follow the procedure below for a child restraint system that requires the use of a top strap.


68


2002 MY TUNDRA_U (OM34417U)


Use the anchor bracket on the back panel to attach the top strap. Anchor brackets are installed for (each) passenger seating position. This symbol the user ready anchor brackets.


locations of


indicates


’02 TUNDRA_U (L/O 0108)


TO USE THE ANCHOR BRACKET: 1. Remove


the passenger head


re-


straint.


2. Lightly push down on the top sur- face of the anchor bracket cover, then pull it forward to remove.


2002 MY TUNDRA_U (OM34417U)


69


’02 TUNDRA_U (L/O 0108)


—Using a top strap (access cab models)


4. Replace


straint.


the passenger head


re-


Outside position


Store any removed covers in a safe place such as the glove box. Be sure to replace all covers when the anchor bracket is not in use.


3. Fix the child restraint system with


the seat belt. Latch bracket and tighten the top strap.


the hook onto


the anchor


instructions


For the child re- straint system, see “Child restraint” in this section.


install


to


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


70


2002 MY TUNDRA_U (OM34417U)


Center position


’02 TUNDRA_U (L/O 0108)


Follow the procedure below for a child restraint system that requires the use of a top strap.


Symbol


Routing devices


Anchor brackets


Use the routing device on the rear of the seat back and the anchor bracket on the side floor to attach the top strap. Anchor brackets are rear seating position. This symbol the user ready anchor brackets.


locations of


indicates


for each


installed


TO USE THE ANCHOR BRACKET: Outside position 1. Remove the head restraint.


2002 MY TUNDRA_U (OM34417U)


71


’02 TUNDRA_U (L/O 0108)


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


Routing device


2. Route


the


top strap


the routing device as shown in the il- lustration.


through


CAUTION


Make sure twisted.


the


top strap


is not


3. Fix the child restraint system with


the seat belt. Latch the anchor bracket on the side floor and tighten the top strap.


the hook onto


instructions


For the child re- straint system, see “Child restraint” in this section.


install


to


72


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


4. Replace the head restraint.


Center position 1. Fold down the cup holder, unfasten the Velcro that attaches the anchor bracket cover, and lift the cover.


2. Route the top strap through the slot on top of the seat, pass the strap through the seat, then latch the hook onto the anchor bracket. Close the cover and return the cup holder to the original position.


2002 MY TUNDRA_U (OM34417U)


73


’02 TUNDRA_U (L/O 0108)


Tilt steering wheel


CAUTION


(cid:1) Do not adjust the steering wheel while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.


(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.


3. Move the child restraint system to


the correct position. Then fix the child restraint system with the seat belt and tighten the top strap.


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.


74


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Outside rear view mirrors—


—Power rear view mirror control


CAUTION


Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.


Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.


To adjust a mirror, use the switches. 1. Master switch—To select the mirror to


be adjusted Push the “L” (left) or “R” (right) switch.


2. Control switch—To move the mirror


Push the switch in the desired direc- tion.


Mirror can be adjusted when key is in the “ACC” or “ON” position.


2002 MY TUNDRA_U (OM34417U)


75


’02 TUNDRA_U (L/O 0108)


—Folding rear view mirrors


Anti–glare inside rear view mirror


NOTICE


If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de–icer to free the mirror.


for parking


The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.


in


CAUTION


Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.


76


2002 MY TUNDRA_U (OM34417U)


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.


’02 TUNDRA_U (L/O 0108)


Sun visors—


CAUTION


Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.


To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). If glare comes from obliquely behind you, extend the plate at the end of the visor (to position 3).


To block the glare from the front when the main sun visor is swung to the lateral side (position 2), swing down the sub vi- sor.


CAUTION


Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti–glare inside rear view mirror and obstruct the rear view.


2002 MY TUNDRA_U (OM34417U)


77


’02 TUNDRA_U (L/O 0108)


—Vanity mirrors (with light)


To use the vanity mirrors, swing down the sun visor and open the cover. The vanity light comes on when you open the cover.


78


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


SECTION 1– 4


OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Personal lights Ignition switch and step lights Cargo lamp Windshield wipers and washer


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


80
81
82
82
82
83
83
83
84


2002 MY TUNDRA_U (OM34417U)


79


’02 TUNDRA_U (L/O 0108)


Headlights and turn signals


HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, tail, license plate and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when the driver’s door is opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off.


the


NOTICE


To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.


the


Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.


80


2002 MY TUNDRA_U (OM34417U)


High–Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.


the lever all


’02 TUNDRA_U (L/O 0108)


Emergency flashers


NOTICE


To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.


TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.


flashers,


turn on


the emergency


To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.


2002 MY TUNDRA_U (OM34417U)


81


’02 TUNDRA_U (L/O 0108)


Instrument panel light control


Front fog lights


Interior light


To adjust the brightness of the instru- ment panel lights, turn the knob.


To turn on the front fog lights, push the switch. They will come on when the headlights are on low beam.


To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the doors are opened. The light goes off when all of the doors are closed.


82


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Personal lights


Ignition switch and step lights


Cargo lamp


The personal lights operate separately. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. The personal light switch has the following positions: “OFF”—Turns the lights off. “DOOR”—Turns the lights on when any of the doors are opened.


For easy access to the ignition switch, the ignition switch light comes on when the driver’s door is opened. The step light also comes on when the driver’s door is opened. The ignition switch light remains on for some is closed.


the driver’s door


time after


2002 MY TUNDRA_U (OM34417U)


83


the


this


time,


indicator


light on the


turn on: Push


the “CARGO LAMP”


the “CARGO LAMP”


The cargo lamp is designed to light up the rear deck of your vehicle. CARGO LAMP OPERATION By pushing “CARGO LAMP” switch To switch once. At instrument panel will come on. To turn off: Push switch once again. By locking and unlocking doors (ve- hicles with the power door lock system) You can operate the cargo lump by this method when all the doors are closed and the the “ACC” or “LOCK” position or the key is removed. To turn on: Unlock the doors with the key or the power door lock switch. The cargo lamp will automatically turn off after 20 seconds. To turn off: Lock the doors with the key or the power door lock switch.


ignition switch


in


is


’02 TUNDRA_U (L/O 0108)


Windshield wipers and washer (intermittent type)


By opening and closing doors To turn on: Open any of the doors. To turn off: Close all the doors: (cid:1) When the ignition switch is in the “ON” position, the cargo lamp will go off im- mediately.


(cid:1) When


the


ignition switch


the “ACC” or “LOCK” position or the key is removed, the cargo lamp will automati- cally go off after 20 seconds.


in


is


CARGO LAMP AUTOMATIC POWER–OFF FUNCTION (cid:1) When


speed exceeds approximately 5 km/h (3 mph), the car- go lamp will go off.


vehicle


the


(cid:1) To prevent


the battery being dis- charged, the cargo lamp will automati- cally go off when the lamp remains on for 30 minutes or more.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Position 3


Intermittent


Slow


Fast


The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.


the band upward to


84


2002 MY TUNDRA_U (OM34417U)


To squirt washer fluid, pull the lever toward you and release it. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield is dry. It may scratch the glass.


’02 TUNDRA_U (L/O 0108)


Windshield wipers and washer (mist type)


In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield is dry. It may scratch the glass.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Slow


Fast


the windshield,


For a single sweep of push the lever up and release it. To squirt washer fluid, pull the lever toward you and release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3.


2002 MY TUNDRA_U (OM34417U)


85


’02 TUNDRA_U (L/O 0108)


86


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


SECTION 1– 5


OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil pressure gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers . . . . . . . . . . . . . . .


88
88
89
90
90
91
91


2002 MY TUNDRA_U (OM34417U)


87


’02 TUNDRA_U (L/O 0108)


Fuel gauge


Engine coolant temperature gauge


the


The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. This fuel gauge has a non–return type needle which remains at the last indicated position when the ignition switch is turned off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


2002 MY TUNDRA_U (OM34417U)


With tachometer


Without tachometer


With tachometer


Without tachometer


88


The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: (cid:1) Driving up a long hill on a hot day. (cid:1) Reducing speed or stopping after high


speed driving.


(cid:1) Idling for a long period with the air conditioning on in stop–and–go traffic.


(cid:1) Towing a trailer.


’02 TUNDRA_U (L/O 0108)


Oil pressure gauge


NOTICE


(cid:2) Do not remove the thermostat in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.


(cid:2) Do not continue driving with an overheated engine. See “If your ve- hicle overheats” in Section 4.


Normal driving


Idling


The oil pressure gauge indicates engine oil pressure when the ignition switch is on. Check it while driving to make sure that the needle is in the proper range. If the oil pressure should stay below the normal range, pull off the road to a safe place and stop immediately. Call a Toyota dealer or qualified repair shop for assistance. Oil pressure may not build up when the oil low. The oil pressure gauge is not designed to indicate oil level, and the oil level must be checked using the level dipstick.


the engine


level


too


is


2002 MY TUNDRA_U (OM34417U)


89


’02 TUNDRA_U (L/O 0108)


Voltmeter


Tachometer


NOTICE


Do not drive the vehicle with the oil pressure below the normal range until the cause is fixed—it may ruin the engine.


The voltmeter tells whether the battery is charged or discharged. Check it while the engine is running—the needle should always indicate as shown above. If the needle reads below or above the normal range while the engine is running, it indicates the charging system needs im- mediate repair. However, it is normal for the needle to drop below the normal range during en- gine starting.


The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over–revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.


NOTICE


Do not let the indicator needle get into the red zone. This may cause severe engine damage.


90


2002 MY TUNDRA_U (OM34417U)


Odometer and two trip meters


This meter displays the odometer and two trip meters. 1. Odometer—Shows


total distance


the


the vehicle has been driven.


2. Two


trip meters—Show


two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.


fuel economy and


the other


’02 TUNDRA_U (L/O 0108)


3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.


to


Service reminder indicators and warning buzzers


If the indicator or buzzer comes on...


Do this.


(a)


(b)


If parking brake is


off, stop immediately and contact Toyota dealer.


Fasten driver’s seat belt.


(indicator and buzzer)


(c)


(d)


(e)


Fasten front passenger’s seat belt.


Stop and check.


Stop and check.


2002 MY TUNDRA_U (OM34417U)


91


’02 TUNDRA_U (L/O 0108)


(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. (cid:1) When the parking brake is applied... (cid:1) When the brake fluid level is low...


CAUTION


It is dangerous to continue driving normally when the brake fluid level is low.


Have your vehicle checked at your Toyota dealer in the following case: (cid:1) The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.


If the indicator or buzzer comes on...


Do this.


If the indicator or buzzer comes on...


Do this.


(f)


(g)


(h)


(i)


(j)


92


Take vehicle to Toyota dealer.


Fill up tank.


Take vehicle to Toyota dealer.


or


(k)


(l)


(m)


Shift front drive control lever out of


“N”.


Stop and check.


Add washer fluid.


Close all doors.


Take vehicle to Toyota dealer immediately.


(n)


Key reminder buzzer


Remove key.


(o)


Four–wheel drive system warning buzzer


Shift the transfer mode again, correctly.


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


(c) Front Passenger’s Seat Belt Re-


minder Light


NOTICE


If the light does not turn off even after the parking brake is released while the engine is running, immedi- ately stop your vehicle at a safe place and contact your Toyota dealer. In this case, the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.


(b) Driver’s Seat Belt Reminder Light


and Buzzer


to


remind you


light and buzzer


This buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the buzzer stops after about 4 to 8 seconds.


flashing and


light keeps


the


the


load


luggage


is placed on


This light reminds you to buckle up the front passenger’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. Howev- er, if a front passenger uses an additional seat cushion, the light may not flash even when the seat belt is not buckled up. If front passenger seat, depending on its weight and how it is placed on the seat, built–in sensors in the seat cushion may detect the pressure, causing the reminder light to keep flashing. (d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.


Do not continue driving if the engine drive belt is broken or loose.


(e) Low Engine Oil Pressure Warning


Light


This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.


light may occasionally


low. It


NOTICE


Do not drive the vehicle with the warning light on—even for one block. It may ruin the engine.


2002 MY TUNDRA_U (OM34417U)


93


’02 TUNDRA_U (L/O 0108)


(f) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings. (cid:1) Empty fuel tank


If the fuel tank is empty, refuel immedi- ately.


(cid:1) Loose fuel tank cap


If the fuel tank cap is loose, securely tighten it.


These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp will not go off even after the several trips, contact your Toyota dealer as soon as possible.


If the fuel tank is not empty or the fuel tank cap is not loose... (cid:1) There is a problem somewhere in the engine, emission control system, auto- matic transmission electrical system or warning light system itself.


if


control


system


inspection


Contact your Toyota dealer as soon as possible to service the vehicle. Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On–Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” in Section 6. (g) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.


(h) “ABS” Warning Light The light comes on when the ignition key is turned to the “ON” position. If the anti– lock brake system works properly, the light turns off after a few seconds. There- after, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti–lock brake system does not operate, but the brake system still operates con- ventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti–lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces. the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ON” posi- tion, or the light remains on.


(cid:1) The light comes on while you are driv-


ing.


94


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


(k) Unengaged “Park” Warning Light transmission and


(with automatic front drive control lever)


(m) Low Windshield Washer Fluid Level Warning Light (with daytime running light system)


This light warns that the windshield wash- er fluid level is too low. Add washer fluid at your earliest opportunity. (For instruc- tions, see “Adding washer fluid” in Section 7–3.) (n) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position. (o) Four–wheel drive system warning


buzzer


This buzzer reminds you that the transfer mode is not selected correctly. If the buzzer sounds when you shift the transfer to “4HI”, “4HI” to “4LO”, or “4LO” to “2WD” mode, in “Four– wheel drive system” in Section 1–6.


to “4HI”, “4LO”


from “2WD”


instructions


follow


the


the


that


light warns


This transmission “Park” mechanism is not engaged. If the front drive control lever is in the “N” posi- tion while the selector lever is in the “P” position, the transmission will disengage and the wheels will not lock.


CAUTION


To restore the park function, shift the front drive control lever out of “N”, or the vehicle can move.


(l) Automatic


Transmission


Fluid


Temperature Warning Light


This light warns that the automatic trans- mission fluid temperature is too high. If this light comes on while you are driv- ing, slow down and pull off the road. Stop the vehicle at a safe place and put the selector lever in “P”. With the engine id- ling, wait until the light goes off. If the light goes off, you may start the vehicle again. If the light does not go off, call a Toyota dealer or qualified repair shop for assistance.


2002 MY TUNDRA_U (OM34417U)


95


A warning light turning on briefly during operation does not indicate a problem. (i) Open Door Warning Light This light remains on until all the doors are completely closed. (j) SRS Warning Light This light will come on when the igni- tion key is turned to the “ACC” or “ON” position. After about 6 seconds, the light will go off. This means the system of the airbag and front seat belt pretensioners are operating properly. The warning light system monitors the air- bag sensor assembly, front airbag sen- sors, front seat belt pretensioner assem- blies, light, interconnecting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while


inflators,


warning


driving.


’02 TUNDRA_U (L/O 0108)


light


SERVICE


CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.


and


The open door warning come on.


light should


3. Close the door.


The open door warning light should go off.


4. Turn the ignition key to “ACC”.


The SRS warning light should come on. It goes off after about 6 seconds.


5. Turn the ignition key to “ON”, but do


not start the engine. All the service reminder indicators ex- cept the open door warning light and SRS warning light should come on. The “ABS” warning light goes off after a few seconds.


If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.


96


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


SECTION 1– 6


OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock Automatic transmission Manual transmission Four–wheel drive system Parking brake Cruise control Clutch start cancel switch


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


98
99
103
105
109
110
112


2002 MY TUNDRA_U (OM34417U)


97


’02 TUNDRA_U (L/O 0108)


Ignition switch with steering lock


You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be in the “P” posi- tion before pushing the key. When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.


CAUTION


For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.


NOTICE


Do not leave the key in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.


2002 MY TUNDRA_U (OM34417U)


“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. 98


the key


leave


in


’02 TUNDRA_U (L/O 0108)


Automatic transmission


Overdrive switch


Selector lever


With the brake pedal depressed, shift while pulling the selector lever toward you. (The ignition switch must be in “ON” or “ACC” position.)


Shift while pulling the selector lever toward you.


Shift normally.


Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” or “ACC” position and the selector lever pulled toward you). (a) Selector lever The shift position is displayed on the in- strument cluster. P: Parking, engine starting and


key removal


R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking


2002 MY TUNDRA_U (OM34417U)


99


’02 TUNDRA_U (L/O 0108)


Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.


2. With your foot holding down the brake


pedal, shift the selector lever to “D”.


When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into the over- drive gear even with the overdrive on.


temperature


low,


is


CAUTION


Never put your foot on the accelera- tor pedal while shifting.


3. Release the parking brake and brake the accelerator pedal


pedal. Depress slowly for smooth starting.


(d) Using engine braking To use engine braking, you can downshift the transmission as follows: (cid:1) Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.


(cid:1) Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than the following speed, and stronger engine braking will be en- abled. Two–wheel drive models 5VZ–FE engine 2UZ–FE engine


115 km/h (71 mph) 120 km/h (75 mph)


(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will automatically be on.


for better


100


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Four–wheel drive models 5VZ–FE engine


Four–wheel drive models 5VZ–FE engine


Front drive control lever in “H2” or “H4”


109 km/h (68 mph)


Front drive control lever in “H2” or “H4”


52 km/h (32 mph)


Front drive control lever in “L4”


Front drive control lever in “L4”


37 km/h (23 mph)


10 km/h


(6 mph)


2UZ–FE engine


2UZ–FE engine


“2WD” or “4HI” mode is selected


“2WD” or “4HI” mode is selected


“4LO” mode is selected


120 km/h (75 mph)


to


41 km/h (25 mph) (cid:1) Shift into the “L” position. The trans- mission will downshift first gear when the vehicle speed drops down to or lower than the following speed, and maximum engine braking will be en- abled. Two–wheel drive models 5VZ–FE engine 2UZ–FE engine


55 km/h (34 mph) 58 km/h (36 mph)


58 km/h (36 mph)


“4LO” mode is selected


11 km/h


(7 mph) Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section.


CAUTION


Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.


surface. Abrupt


(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.


NOTICE


(cid:2) Be careful not to over–rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference: Two–wheel drive models


5VZ–FE engine—


“2” “L”


. . . . . . . . . . . . . . . . . . . 2UZ–FE engine—


115 km/h (71 mph) 60 km/h (37 mph)


“2” “L”


. . . . . . . . . . . . . . . . . . .


120 km/h (75 mph) 65 km/h (40 mph)


2002 MY TUNDRA_U (OM34417U)


101


’02 TUNDRA_U (L/O 0108)


(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.


NOTICE


Never shift into reverse while the ve- hicle is moving.


(g) Parking 1. Bring the vehicle to a complete stop. 2. With


the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.


3. With


the brake pedal pressed down, shift the selector lever to the “P” posi- tion.


CAUTION


Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.


(h) Good driving practice (cid:1) If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.


(cid:1) When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.


CAUTION


Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.


NOTICE


Do not hold the vehicle on an up- grade with the accelerator pedal. It can cause the transmission to over- heat. Always use the brake pedal or parking brake.


Four–wheel drive models


5VZ–FE engine— Front control lever in “H2” or “H4” “2” “L”


110 km/h (68 mph) 60 km/h (37 mph)


. . . . . . . . . . . . . . . . . . .


Front control lever in “L4”


“2” “L”


. . . . . . . . . . . . . . . . . . . . 2UZ–FE engine— “2WD” or “4HI” mode is selected


40 km/h (25 mph) 20 km/h (12 mph)


“2” “L”


. . . . . . . . . . . . . . . . . . .


120 km/h (75 mph) 65 km/h (40 mph)


“4LO” mode is selected


“2” “L”


. . . . . . . . . . . . . . . . . . . .


45 km/h (28 mph) 25 km/h (16 mph) (cid:2) Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.


102


2002 MY TUNDRA_U (OM34417U)


(i) Rocking your vehicle if stuck


CAUTION


If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Do not attempt this procedure if people or objects are anywhere near the ve- hicle. During the rocking operation the vehicle may suddenly move for- ward or backward as it becomes un- stuck, causing injury or damage to nearby people or objects.


NOTICE


If you rock your vehicle, observe the following precautions to prevent dam- age to the transmission and other parts. (cid:2) Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.


’02 TUNDRA_U (L/O 0108)


Manual transmission


(cid:2) Do not race the engine and avoid


spinning the wheels.


(cid:2) If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.


The shift pattern is as shown above. Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle when stopped on an uphill grade—use the parking brake.


2002 MY TUNDRA_U (OM34417U)


103


’02 TUNDRA_U (L/O 0108)


Recommended shifting speeds The transmission is fully synchronized and upshifting or downshifting is easy. For fuel economy and vehicle performance, you should upshift or downshift at the following speeds:


the best compromise between


Maximum allowable speeds To get on a highway or to pass slower traffic, maximum acceleration may be nec- essary. Make sure you observe the follow- ing maximum allowable speeds in each gear: Two–wheel drive models


gear


km/h (mph)


1 to 2 or 2 to 1
2 to 3 or 3 to 2
3 to 4 or 4 to 3
4 to 5 or 5 to 4


24 (15) 40 (25) 64 (40) 72 (45)


Downshift to the appropriate gear if accel- eration is needed when you are cruising below the above downshifting speeds. Upshifting too too soon or downshifting late will cause lugging, and possibly ping- ing. Regularly revving the engine to maxi- mum speed in each gear will cause ex- cessive engine wear and high fuel consumption.


gear


km/h (mph) 45 (28) 85 (53) 125 (78) 165 (112)


Four–wheel drive models


gear


km/h (mph)


“H2” or “H4”


45 (28) 85 (53) 125 (78) 165 (103)


“L4”


(9) 15
30 (18) 45 (28) 70 (43)


NOTICE


Do not downshift if you are going faster than the maximum allowable speed for the next lower gear.


Good driving practice (cid:1) If it is difficult to shift into reverse, put the transmission in neutral, release the clutch pedal momentarily, and then try again.


(cid:1) When towing a trailer, in order to main- tain engine braking efficiency, do not use fifth gear.


CAUTION


Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.


surface. Abrupt


NOTICE


Make sure the vehicle is completely stopped before shifting into reverse.


104


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Four–wheel drive system— (a) Front drive control (lever type)


(a) Front drive control (button type)


“N” (neutral position): Lever at “N” No power is delivered to the wheels. The vehicle must be stopped. “L4” (low speed position, four–wheel drive): Lever at “L4” Use this for maximum power and traction. Use “L4” for climbing or descending steep hills, off–road driving, and hard pulling in sand, mud or deep snow. The

Loading...
x