Download PDF Manual

ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while


to service


driving.


(cid:1) If either front seat belt does not retract or cannot be pulled out due to a mal- function or activation of the relevant front seat belt pretensioner.


37


’02 TUNDRA_U (L/O 0108)


SRS driver and front passenger airbags


In response to a severe frontal impact, the SRS airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS airbags help to reduce inju- ries mainly to the driver’s or right front passenger’s head or chest caused by di- rectly hitting the steering wheel or dash- board. The front passenger airbag is acti- vated even with no passenger in the front seat. Be sure to wear your seat belt properly. Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seat belt restraint system by the driver and right front pas- senger when the SRS airbags are inflated.


The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide further protection for the driver and right front passenger in addition to the primary safety protection provided by the seat belts. (cid:1) Vehicles with separate front seats—The SRS airbags are designed to protect the driver and front passenger.


(cid:1) Vehicles with bench type front seats— The SRS airbags are designed to pro- tect the driver and right–front passen- ger. They are not designed to protect occupant in the center position.


In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the front seat belt pretensioners to operate.


(cid:1) Either front seat belt pretensioner as- sembly is scratched, cracked, or otherwise dam- aged.


surrounding


area


or


38


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


The driver or front passengers who are too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. To- yota strongly recommends that: (cid:1) The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle. (cid:1) The


far back as possible from the dash- board.


front passengers sit as


(cid:1) All vehicle occupants be properly restrained using the available seat belts.


CAUTION


(cid:1) Make sure that the indicator light is


off.


(cid:1) Do not turn off the passenger air- bag manual on–off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the right front passenger seating position.


(cid:1) When the passenger airbag manual on–off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.


Indicator light


airbag


system


passenger


The is equipped with a manual on–off switch and indicator light. Turning the passen- ger airbag manual on–off switch clock- wise to the “ON” position makes the passenger airbag system operational. Turning the passenger airbag manual on–off switch counterclockwise to the “OFF” position disables the passenger airbag system. The indicator light on the passenger airbag manual on–off switch will come on when the passen- ger airbag system has been disabled. See switch” in this section for detail.


“Passenger airbag manual on–off


2002 MY TUNDRA_U (OM34417U)


39


’02 TUNDRA_U (L/O 0108)


TABLE 1: A PASSENGER RISK GROUP


Infant. An infant (less than 1 year old) who must ride in the front seat because: (cid:1) Vehicle has no rear seat; (cid:1) Vehicle has a rear seat too small to accommodate a rear–facing infant seat;


or


(cid:1) The infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can constantly monitor the child’s condition.


Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: (cid:1) Vehicle has no rear seat: (cid:1) Although children ages 1 to 12 ride in the rear seat(s) whenever possible,


children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of vehicle; or


(cid:1) The child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.


Medical condition. A passenger has a medical condition which according to his or her physician: (cid:1) Causes the passenger airbag to pose a special risk for the passenger: and (cid:1) Makes the potential harm from the passenger airbag in a crash greater than the potential harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard, or windshield in a crash.


For more detailed information concerning about the passenger risk group, please contact NHTSA at 1–800–424–9393 or Transport Canada at 1–800–333–0371.


40


2002 MY TUNDRA_U (OM34417U)


This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” in Section 1–5.)


light system monitors


reminder


“Service


’02 TUNDRA_U (L/O 0108)


this


However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the nose of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It is possible that in some collisions at the lower zone of airbag sensor detection and activation the SRS airbags and seat belt pretensioners will not operate all together. For the safety of all occupants, always wear your seat belts properly.


Collision from the rear


Collision from the side


Vehicle rollover


The SRS airbags are not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low–speed frontal collision.


2002 MY TUNDRA_U (OM34417U)


41


The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when impacting straight into a fixed barrier that does not move or deform. If the severity of the impact is below the above threshold the SRS airbags may not deploy.


level,


’02 TUNDRA_U (L/O 0108)


Hitting a curb, edge of pavement or hard material


Falling into or jumping over a deep hole


Landing hard or vehicle falling


The SRS airbags may deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


In a severe frontal impact, the sensors detect deceleration and the system trig- gers the airbag inflators. Then a chemical reaction in the inflators quickly fills the airbags with non–toxic gas to help restrain the forward motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non–toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.


The SRS airbag system consists mainly of the following components, and their loca- tions are shown in the illustration. 1. Front airbag sensors 2. SRS warning light 3. Airbag module for right front passenger


(airbag and inflator)


4. Passenger airbag manual on–off switch 5. Airbag sensor assembly 6. Airbag module for driver


(airbag and inflator)


The airbag sensor assembly consists of a safing sensor and airbag sensor.


42


2002 MY TUNDRA_U (OM34417U)


the windshield as


A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.


’02 TUNDRA_U (L/O 0108)


(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by the deploy- ing airbags. An infant or child who is too small to use a seat belt should be properly secured using a child restraint system. As to access cab models, Toyota recommends that all infants and children be placed in the rear seat of the ve- hicle and properly restrained. The rear seat is the safest for infants and children. For instructions con- cerning the installation of a child restraint system, see “Child re- straint” in this section.


CAUTION


(cid:1) The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and right front passenger side seat belt systems. The front seat occupants can be killed or seriously injured by the inflating airbags if they do not wear the available seat belts prop- erly. During sudden braking just be- fore a collision, an unrestrained driver or front passenger can move forward into direct contact with or close proximity to the airbag which may then deploy during the colli- sion. To ensure maximum protection in an accident, the driver and all passengers the vehicle must wear their seat belts properly. Wear- ing a seat belt properly during an the chances of accident reduces death or serious injury or being thrown out of the vehicle. For instructions and precautions con- cerning the seat belt system, see “Seat belts” in this section.


in


2002 MY TUNDRA_U (OM34417U)


43


’02 TUNDRA_U (L/O 0108)


CAUTION


A member of a passenger risk group should never sit or be occupied in the right front passenger seat with airbag manual on–off switch in the “ON” position. (For details, see “SRS driver and front passenger airbags” in this section.)


(cid:1) A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. For the installation of a child restraint sys- tem, see “Child restraint” in this section.


instructions concerning


CAUTION


(cid:1) Never put a rear–facing child re- straint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an acci- dent, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child.


44


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


(cid:1) Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or serious- ly injured. Sit up straight and well back in the seat, and always use your seat belt properly.


(cid:1) Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag inflates with con- siderable speed and force; the child may be killed or seriously injured. (cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” in this section.


(cid:1) Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the airbag system. They might restrict inflation or cause death or serious injury as they are projected rear- ward by the force of deploying air- bags. Likewise, the driver and front passenger should not hold things in their arms or on their knees.


2002 MY TUNDRA_U (OM34417U)


45


’02 TUNDRA_U (L/O 0108)


(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS airbag inflation or disable the system, which could result in death or serious injury. instructions Failure to follow these can result in death or serious injury.


NOTICE


Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. (cid:2) Installation of electronic devices such as a mobile two–way radio, cassette tape player or compact disc player


(cid:2) Modification of the suspension sys-


tem


(cid:2) Modification of the front end struc-


ture


(cid:2) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


(cid:2) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag


46


2002 MY TUNDRA_U (OM34417U)


this


This SRS airbag system has a service reminder indicator to inform the driver of operating problems. If either of the follow- ing conditions occurs, indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while


driving.


’02 TUNDRA_U (L/O 0108)


Passenger airbag manual on–off switch


Indicator light


This on–off switch is designed to dis- able the passenger airbag in order to allow usage, if necessary, of a member of a passenger risk group identified in TABLE 1 is occupying the right front passenger seating position. (For details, see “SRS driver and front passenger airbags” in this section.) Operate on–off switch as follows: Insert key into the keyhole and turn it. To turn passenger airbag on: Turn the key clockwise to the “ON” position. To turn passenger airbag off: Turn the key counterclockwise to the “OFF” position. The indicator comes on when the passen- ger airbag system is off.


2002 MY TUNDRA_U (OM34417U)


CAUTION


(cid:1) Make sure that the indicator light is


off.


(cid:1) Do not turn off the passenger air- bag manual on–off switch except when a member of a passenger risk group identified in TABLE 1 (page 40) is occupying the right front pas- senger seating position.


(cid:1) When the passenger airbag manual on–off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.


For details, see “SRS driver and front passenger airbags” in this section.


47


In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS airbags have been inflated. (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS airbags to inflate.


front


(cid:1) The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.


passenger


airbag


NOTICE


Do not disconnect the battery cables before contacting your Toyota dealer.


’02 TUNDRA_U (L/O 0108)


(cid:1) Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.


child


the


by


Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the seat and must be restrained using the vehicle’s seat belt. See “Seat belts” for details.


CAUTION


(cid:1) For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.


(cid:1) STANDARD CAB MODELS—


Toyota strongly urges use of a proper child restraint system which conforms to the size of the child. ACCESS CAB MODELS— Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.)


force of


the


48


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


When not using the child restraint system, keep it secured with the seat belt or place it somewhere other the passenger compartment. This will prevent it from in- juring passengers in the event of a sud- den stop or accident.


than


the manufacturer’s


—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with either the lap belt or the lap portion of the lap/ shoulder belt. You must carefully con- sult instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. The child restraint system should be installed on the rear seat if your vehicle is equipped with rear seats. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.


CAUTION


the


force of


(cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.) installing the child restraint system, make sure it is secured in place according to the manufactur- er’s is not re- instructions. strained securely, it may cause death or serious injury to the child in the event of a sudden stop or accident.


(cid:1) After


If


it


2002 MY TUNDRA_U (OM34417U)


49


’02 TUNDRA_U (L/O 0108)


—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchors for securing the top strap of a child restraint system. For instructions on how to use the anchor bracket, see “—Using a top strap” in this section.


(A) Infant seat


(C) Booster seat


50


2002 MY TUNDRA_U (OM34417U)


(B) Convertible seat


’02 TUNDRA_U (L/O 0108)


—Installation with 2–point type seat belt


(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.


With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion.


the child restraint system


CAUTION


Ignoring the above instructions may result in a serious injury in case of an accident.


CAUTION


airbag manual


Never put a rear–facing child restraint system on the front seat with the passenger on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.


2002 MY TUNDRA_U (OM34417U)


51


’02 TUNDRA_U (L/O 0108)


CAUTION


If you must put a rear–facing child restraint system on the front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.


When you put a rear–facing child re- straint system on the front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.


CAUTION


(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause death or seri- ous injury to the child and front passenger in case of sudden brak- ing or a collision.


(cid:1) If your driving position is not satis- the child restraint


factory, system at another position.


install


52


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


2. While pressing the infant seat


firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.


2002 MY TUNDRA_U (OM34417U)


53


1. Run


the


lap belt


the center


infant seat


through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.


following


’02 TUNDRA_U (L/O 0108)


CAUTION


3. To remove the infant seat, press the


buckle–release button.


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing or rear–facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- struction about the applicable child’s age and size as well as directions for installing the child restraint system. With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion.


the child restraint system


54


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


Ignoring the above instructions may result in a serious injury in case of an accident.


CAUTION


airbag manual


Rear–facing child restraint system: Never put a rear–facing child restraint system on the front seat with the passenger on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.


When you put a rear–facing child re- straint system on the front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.


2002 MY TUNDRA_U (OM34417U)


55


’02 TUNDRA_U (L/O 0108)


CAUTION


CAUTION


If you must put a rear–facing child restraint system on the front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.


Forward–facing child restraint system: A forward–facing child restraint sys- tem should never be put on the front seat with the passenger airbag manu- al on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position.


CAUTION


(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause death or seri- ous injury to the child and front passenger in case of sudden brak- ing or a collision.


(cid:1) If your driving position is not satis- the child restraint


factory, system at another position.


install


56


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


2. While pressing


the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.


2002 MY TUNDRA_U (OM34417U)


57


1. Run


lap belt


the center


through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.


the convertible seat provided insert the


’02 TUNDRA_U (L/O 0108)


—Installation with 3–point type seat belt


CAUTION


3. To remove the convertible seat, press


the buckle–release button.


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.


58


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


If you must put a rear–facing child restraint system on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.


CAUTION


Never put a rear–facing child restraint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.


When you put a rear–facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.


2002 MY TUNDRA_U (OM34417U)


59


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


CAUTION


(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause death or seri- ous injury to the child and front passenger in case of sudden brak- ing or a collision.


(cid:1) If your driving position is not satis- the child restraint


factory, system at another position.


install


60


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.


the


To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.


3. While pressing the infant seat


firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


2002 MY TUNDRA_U (OM34417U)


61


’02 TUNDRA_U (L/O 0108)


4. To remove the infant seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing or rear–facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instruction about the applicable child’s age and size as well as directions for installing the child restraint system.


follow


CAUTION


Rear–facing child restraint system: Never put a rear–facing child restraint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.


62


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


CAUTION


CAUTION


If you must put a rear–facing child restraint system on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.


Forward–facing child restraint system: A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)


2002 MY TUNDRA_U (OM34417U)


63


When you put a rear–facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.


’02 TUNDRA_U (L/O 0108)


CAUTION


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


CAUTION


(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause death or seri- ous injury to the child and front passenger in case of sudden brak- ing or a collision.


1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


provided insert the


by tab


(cid:1) If your driving position is not satis- the child restraint


factory, system at another position.


install


64


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.


3. While pressing


the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


2002 MY TUNDRA_U (OM34417U)


65


’02 TUNDRA_U (L/O 0108)


CAUTION


A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)


4. To remove the convertible seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward–fac- ing position only.


66


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.


from


CAUTION


(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.


to do so could reduce


(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.


(cid:1) For child’s safety, do not place the


shoulder belt under child’s arm.


(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.


2002 MY TUNDRA_U (OM34417U)


67


1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.


insert


the


tab


Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.


’02 TUNDRA_U (L/O 0108)


—Using a top strap (standard cab models)


Symbol


Symbol


Anchor bracket


Separate seat


Anchor brackets


Bench seat


2. To remove the child restraint system, press the buckle–release button and al- low the belt to retract.


Follow the procedure below for a child restraint system that requires the use of a top strap.


68


2002 MY TUNDRA_U (OM34417U)


Use the anchor bracket on the back panel to attach the top strap. Anchor brackets are installed for (each) passenger seating position. This symbol the user ready anchor brackets.


locations of


indicates


’02 TUNDRA_U (L/O 0108)


TO USE THE ANCHOR BRACKET: 1. Remove


the passenger head


re-


straint.


2. Lightly push down on the top sur- face of the anchor bracket cover, then pull it forward to remove.


2002 MY TUNDRA_U (OM34417U)


69


’02 TUNDRA_U (L/O 0108)


—Using a top strap (access cab models)


4. Replace


straint.


the passenger head


re-


Outside position


Store any removed covers in a safe place such as the glove box. Be sure to replace all covers when the anchor bracket is not in use.


3. Fix the child restraint system with


the seat belt. Latch bracket and tighten the top strap.


the hook onto


the anchor


instructions


For the child re- straint system, see “Child restraint” in this section.


install


to


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


70


2002 MY TUNDRA_U (OM34417U)


Center position


’02 TUNDRA_U (L/O 0108)


Follow the procedure below for a child restraint system that requires the use of a top strap.


Symbol


Routing devices


Anchor brackets


Use the routing device on the rear of the seat back and the anchor bracket on the side floor to attach the top strap. Anchor brackets are rear seating position. This symbol the user ready anchor brackets.


locations of


indicates


for each


installed


TO USE THE ANCHOR BRACKET: Outside position 1. Remove the head restraint.


2002 MY TUNDRA_U (OM34417U)


71


’02 TUNDRA_U (L/O 0108)


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


Routing device


2. Route


the


top strap


the routing device as shown in the il- lustration.


through


CAUTION


Make sure twisted.


the


top strap


is not


3. Fix the child restraint system with


the seat belt. Latch the anchor bracket on the side floor and tighten the top strap.


the hook onto


instructions


For the child re- straint system, see “Child restraint” in this section.


install


to


72


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


4. Replace the head restraint.


Center position 1. Fold down the cup holder, unfasten the Velcro that attaches the anchor bracket cover, and lift the cover.


2. Route the top strap through the slot on top of the seat, pass the strap through the seat, then latch the hook onto the anchor bracket. Close the cover and return the cup holder to the original position.


2002 MY TUNDRA_U (OM34417U)


73


’02 TUNDRA_U (L/O 0108)


Tilt steering wheel


CAUTION


(cid:1) Do not adjust the steering wheel while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.


(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.


3. Move the child restraint system to


the correct position. Then fix the child restraint system with the seat belt and tighten the top strap.


CAUTION


Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.


To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.


74


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Outside rear view mirrors—


—Power rear view mirror control


CAUTION


Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.


Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.


To adjust a mirror, use the switches. 1. Master switch—To select the mirror to


be adjusted Push the “L” (left) or “R” (right) switch.


2. Control switch—To move the mirror


Push the switch in the desired direc- tion.


Mirror can be adjusted when key is in the “ACC” or “ON” position.


2002 MY TUNDRA_U (OM34417U)


75


’02 TUNDRA_U (L/O 0108)


—Folding rear view mirrors


Anti–glare inside rear view mirror


NOTICE


If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de–icer to free the mirror.


for parking


The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.


in


CAUTION


Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.


76


2002 MY TUNDRA_U (OM34417U)


Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.


’02 TUNDRA_U (L/O 0108)


Sun visors—


CAUTION


Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.


To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). If glare comes from obliquely behind you, extend the plate at the end of the visor (to position 3).


To block the glare from the front when the main sun visor is swung to the lateral side (position 2), swing down the sub vi- sor.


CAUTION


Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti–glare inside rear view mirror and obstruct the rear view.


2002 MY TUNDRA_U (OM34417U)


77


’02 TUNDRA_U (L/O 0108)


—Vanity mirrors (with light)


To use the vanity mirrors, swing down the sun visor and open the cover. The vanity light comes on when you open the cover.


78


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


SECTION 1– 4


OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Personal lights Ignition switch and step lights Cargo lamp Windshield wipers and washer


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


80
81
82
82
82
83
83
83
84


2002 MY TUNDRA_U (OM34417U)


79


’02 TUNDRA_U (L/O 0108)


Headlights and turn signals


HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, tail, license plate and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when the driver’s door is opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off.


the


NOTICE


To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.


the


Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.


80


2002 MY TUNDRA_U (OM34417U)


High–Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.


the lever all


’02 TUNDRA_U (L/O 0108)


Emergency flashers


NOTICE


To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.


TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.


flashers,


turn on


the emergency


To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.


2002 MY TUNDRA_U (OM34417U)


81


’02 TUNDRA_U (L/O 0108)


Instrument panel light control


Front fog lights


Interior light


To adjust the brightness of the instru- ment panel lights, turn the knob.


To turn on the front fog lights, push the switch. They will come on when the headlights are on low beam.


To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the doors are opened. The light goes off when all of the doors are closed.


82


2002 MY TUNDRA_U (OM34417U)


’02 TUNDRA_U (L/O 0108)


Personal lights


Ignition switch and step lights


Cargo lamp


The personal lights operate separately. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. The personal light switch has the following positions: “OFF”—Turns the lights off. “DOOR”—Turns the lights on when any of the doors are opened.


For easy access to the ignition switch, the ignition switch light comes on when the driver’s door is opened. The step light also comes on when the driver’s door is opened. The ignition switch light remains on for some is closed.


the driver’s door


time after


2002 MY TUNDRA_U (OM34417U)


83


the


this


time,


indicator


light on the


turn on: Push


the “CARGO LAMP”


the “CARGO LAMP”


The cargo lamp is designed to light up the rear deck of your vehicle. CARGO LAMP OPERATION By pushing “CARGO LAMP” switch To switch once. At instrument panel will come on. To turn off: Push switch once again. By locking and unlocking doors (ve- hicles with the power door lock system) You can operate the cargo lump by this method when all the doors are closed and the the “ACC” or “LOCK” position or the key is removed. To turn on: Unlock the doors with the key or the power door lock switch. The cargo lamp will automatically turn off after 20 seconds. To turn off: Lock the doors with the key or the power door lock switch.


ignition switch


in


is


’02 TUNDRA_U (L/O 0108)


Windshield wipers and washer (intermittent type)


By opening and closing doors To turn on: Open any of the doors. To turn off: Close all the doors: (cid:1) When the ignition switch is in the “ON” position, the cargo lamp will go off im- mediately.


(cid:1) When


the


ignition switch


the “ACC” or “LOCK” position or the key is removed, the cargo lamp will automati- cally go off after 20 seconds.


in


is


CARGO LAMP AUTOMATIC POWER–OFF FUNCTION (cid:1) When


speed exceeds approximately 5 km/h (3 mph), the car- go lamp will go off.


vehicle


the


(cid:1) To prevent


the battery being dis- charged, the cargo lamp will automati- cally go off when the lamp remains on for 30 minutes or more.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Position 3


Intermittent


Slow


Fast


The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.


the band upward to


84


2002 MY TUNDRA_U (OM34417U)


To squirt washer fluid, pull the lever toward you and release it. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield is dry. It may scratch the glass.


’02 TUNDRA_U (L/O 0108)


Windshield wipers and washer (mist type)


In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.


the washer


NOTICE


Do not operate the wipers if the wind- shield is dry. It may scratch the glass.


To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.


Lever position


Speed setting


Position 1


Position 2


Slow


Fast


the windshield,


For a single sweep of push the lever up and release it. To squirt washer fluid, pull the lever toward you and release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3.


2002 MY TUNDRA_U (OM34417U)


85


’02 TUNDRA_U (L/O 0108)


86

Loading...
x