2001 Toyota Tacoma Owners Manual

airbag manual on–off switch)

Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.

(A) Infant seat

(B) Convertible seat

58

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

—Installation with 2–point type seat belt

(C) Booster seat

(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.

the child restraint system

With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion. Split bench seat— Adjust the passenger’s seat forward and rearward travel as well as seatback posi- tion so that the child restraint system is securely restrained.

CAUTION

Ignoring the above instructions may result in a serious injury in case of an accident.

2001 TACOMA (OM35766U)

59

’01 Tacoma U (L/O 0009)

CAUTION

If you must put a rear–facing child restraint system on the front passen- ger seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.

CAUTION

Never put a rear–facing child restraint system on the front passenger seat with the passenger airbag manual on– off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or se- rious injury to the child.

When you put a rear–facing child re- straint system on the front passenger seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

60

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. While pressing the infant seat

firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.

2001 TACOMA (OM35766U)

61

1. Run

the

lap belt

the center

infant seat

through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.

following

’01 Tacoma U (L/O 0009)

CAUTION

3. To remove the infant seat, press the

buckle–release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing and rear–facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instructions about the applicable child’s age and size as well as directions for installing a child restraint system.

follow

62

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

the child restraint system

With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion. Split bench seat— Adjust forward and rearward travel as well as seatback posi- tion so that the child restraint system is securely restrained.

the passenger seat

CAUTION

CAUTION

Ignoring the above instructions may result in a serious injury in case of an accident.

Rear–facing child restraint system: Never put a rear–facing child restraint system on the front passenger seat with the passenger airbag manual on– off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or se- rious injury to the child.

When you put a rear–facing child re- straint system on the front passenger seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

2001 TACOMA (OM35766U)

63

’01 Tacoma U (L/O 0009)

CAUTION

CAUTION

If you must put a rear–facing child restraint system on the front passen- ger seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.

Forward–facing child restraint system: A forward–facing child restraint sys- tem should never be put on the front the passenger passenger seat with airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position.

64

2001 TACOMA (OM35766U)

1. Run

lap belt

the center

through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.

the convertible seat provided insert the

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. While pressing

the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2001 TACOMA (OM35766U)

65

’01 Tacoma U (L/O 0009)

—Installation with 3–point type seat belt

3. To remove the convertible seat, press

the buckle–release button.

(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.

WHEN INSTALLING ON THE REAR SEAT (Xtra–cab models): Raise the bottom cushion before instal- ling the child restraint system. If your child restraint system is too large, you can use the folding table as an auxil- iary support. For instructions about how to stand table, see “Rear cup holder (Xtra–cab models)” in Section 1–9.

the

66

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

If you must put a rear–facing child restraint system on the right front seat, make sure the front passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.

CAUTION

Never put a rear–facing child restraint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.

When you put a rear–facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

2001 TACOMA (OM35766U)

67

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

CAUTION

(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause severe injury to the child and front passenger in case of sudden braking or a colli- sion.

(cid:1) If your driving position is not satis- the child restraint

factory, system at another position.

install

68

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2001 TACOMA (OM35766U)

69

’01 Tacoma U (L/O 0009)

4. To remove the infant seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing and rear–facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instruction about the applicable child’s age and size as well as directions for installing a child restraint system.

follow

CAUTION

Rear–facing child restraint system: Never put a rear–facing child restraint system on the right front seat with the passenger airbag manual on–off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child.

70

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

CAUTION

If you must put a rear–facing child restraint system on the right front seat, make sure the passenger airbag manual on–off switch is in the “OFF” position and that the indicator light is on.

Forward–facing child restraint system: A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)

2001 TACOMA (OM35766U)

71

When you put a rear–facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on–off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

(cid:1) Do not put a rear–facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause severe injury to the child and front passenger in case of sudden braking or a colli- sion.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

(cid:1) If your driving position is not satis- the child restraint

factory, system at another position.

install

72

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2001 TACOMA (OM35766U)

73

’01 Tacoma U (L/O 0009)

CAUTION

A forward–facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on–off switch in the “ON” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)

4. To remove the convertible seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward–fac- ing position only.

74

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2001 TACOMA (OM35766U)

75

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

the

tab

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.

’01 Tacoma U (L/O 0009)

—Types of child restraint system (vehicles without passenger airbag manual on–off switch) Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.

2. To remove the child restraint system, press the buckle–release button and al- low the belt to retract.

(A) Infant seat

76

2001 TACOMA (OM35766U)

(B) Convertible seat

’01 Tacoma U (L/O 0009)

—Installation with 2–point type seat belt

(C) Booster seat

(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.

CAUTION

Do not put a rear–facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.

2001 TACOMA (OM35766U)

77

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. While pressing the infant seat

firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.

1. Run

the

lap belt

the center

infant seat

through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.

following

78

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

3. To remove the infant seat, press the

buckle–release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing and rear–facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instructions about the applicable child’s age and size as well as direction for installing of a child restraint system.

follow

2001 TACOMA (OM35766U)

79

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

Do not put a rear–facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.

1. Run

lap belt

the center

through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.

the convertible seat provided insert the

80

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

2. While pressing

the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.

CAUTION

3. To remove the convertible seat, press

the buckle–release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2001 TACOMA (OM35766U)

81

’01 Tacoma U (L/O 0009)

—Installation with 3–point type seat belt

(A) INFANT SEAT INSTALLATION An infant seat is used in rear–facing position only.

CAUTION

(cid:1) Never put a rear–facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.

(cid:1) Do not put a rear–facing child re- straint system in the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.

82

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

2001 TACOMA (OM35766U)

83

’01 Tacoma U (L/O 0009)

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

84

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

Move seat fully back

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward– facing and rear–facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- structions about the applicable child’s age and size as well as directions for installing a child restraint system.

CAUTION

(cid:1) Never put a rear–facing child re- straint system on the front passen- ger seat because the force of the rapid inflation of the front passen- ger airbag can cause death or seri- ous injury to the child.

(cid:1) A forward–facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

2001 TACOMA (OM35766U)

85

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

(cid:1) Do not put a rear–facing child re- straint system in the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

86

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2001 TACOMA (OM35766U)

87

’01 Tacoma U (L/O 0009)

4. To remove the convertible seat, press the buckle–release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward–fac- ing position only.

Move seat fully back

CAUTION

A forward–facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of the deploying airbag could cause death or serious injury to the child.

88

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

(cid:1) Both high–positioned lap belts and loose–fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on a child’s hips as possible.

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2001 TACOMA (OM35766U)

89

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

the

tab

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.

’01 Tacoma U (L/O 0009)

—Using a top strap (regular and double cab models)

2. To remove the child restraint system, press the buckle–release button and al- low the belt to retract.

Regular cab with bench seat

Double cab with rear seat

Follow the procedure below for a child restraint system that requires the use of a top strap.

90

2001 TACOMA (OM35766U)

Regular cab with separate seat

’01 Tacoma U (L/O 0009)

Anchor brackets

Anchor brackets

Regular cab with bench seat

Double cab with rear seat

Anchor bracket

Use the anchor bracket on the back panel to attach the top strap. Regular cab models—

Anchor brackets are installed for (each) passenger seating position.

Double cab models—

Anchor brackets are installed for each rear seating position.

TO USE THE ANCHOR BRACKET: Regular cab with bench seat— 1. Pull the seatback release lever and swing the seatback forward slightly, then latch the hook onto the anchor bracket. Return the seatback to its original position, then tighten the top strap.

Regular cab with separate seat

2001 TACOMA (OM35766U)

91

’01 Tacoma U (L/O 0009)

CAUTION

(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback.

is securely

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

Regular cab with separate seat— 1. Remove

the passenger head

re-

straint.

2. Fix the child restraint system with

the seat belt.

For instructions on installing the child re- straint system, see “Child restraint” in this section.

92

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

2. Pull the seatback release lever and swing the seatback forward slightly, then latch the hook onto the anchor bracket. Return the seatback to upright posi- tion, then tighten the top strap.

CAUTION

(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback.

is securely

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

3. Fix the child restraint system with

the seat belt. Replace straint.

the passenger head

re-

For instructions on installing the child re- straint system, see “Child restraint” in this section.

2001 TACOMA (OM35766U)

93

’01 Tacoma U (L/O 0009)

Double cab with rear seat— 1. Remove the head restraint (outside

position only).

2. Pull the seatback release lever and swing the seatback forward slightly, then latch the hook onto the anchor bracket. Return the seatback to upright posi- tion, then tighten the top strap.

3. Fix the child restraint system with

the seat belt. Replace the head restraint (outside position only).

For instructions on installing the child re- straint system, see “Child restraint” in this section.

94

2001 TACOMA (OM35766U)

CAUTION

(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback.

is securely

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

’01 Tacoma U (L/O 0009)

—Using a top strap (Xtra–cab models)

Front outside position

Rear outside position

Follow the procedure below for a child restraint system that requires the use of a top strap.

Front center position

2001 TACOMA (OM35766U)

95

’01 Tacoma U (L/O 0009)

Routing device

Upper anchor bracket

Lower anchor bracket

is

the routing device and the anchor

Use bracket to attach the top strap. Upper anchor bracket for right–front passenger’s seating position, lower anchor bracket is installed for front center seating position (with split bench seat) or right–rear seating position. This symbol user ready anchor bracket.

locations of

indicates

installed

the

TO USE THE ANCHOR BRACKET: Front outside position— 1. Remove

the passenger head

straint.

re-

2. Fix the child restraint system with

the seat belt. Latch the anchor bracket on the back panel and tight- en the top strap.

the hook onto

For instructions on installing the child re- straint system, see “Child restraint” in this section.

96

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

3. Replace the head restraint.

Front center position— Fix the child restraint system with the seat belt. Latch the hook onto the rear lower an- chor bracket and tighten the top strap. For instructions on installing the child re- straint system, see “Child restraint” in this section.

2001 TACOMA (OM35766U)

97

’01 Tacoma U (L/O 0009)

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

Routing device

Rear outside position— 1. Lightly push down on the top sur- face of the anchor bracket cover with the symbol mark shown in the illustration, then pull it forward to remove.

98

2001 TACOMA (OM35766U)

2. Fix the child restraint system with

the seat belt. Route the routing device as shown in the il- lustration.

top strap

through

the

For instructions on installing the child re- straint system, see “Child restraint” in this section.

CAUTION

Make sure twisted.

the

top strap

is not

’01 Tacoma U (L/O 0009)

Tilt steering wheel

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

3. Latch the hook onto the rear lower anchor bracket and tighten the top strap.

Store the removed cover in a safe place such as the glove box. Be sure to replace the cover when the anchor bracket is not in use.

To change the steering wheel angle: Hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- lease the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

2001 TACOMA (OM35766U)

99

’01 Tacoma U (L/O 0009)

Outside rear view mirrors—

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

100

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

—Rear view mirror control (lever type)

—Rear view mirror control (power type)

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirror can be adjusted when key is in the “ACC” or “ON” position.

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de–icer to free the mirror.

To adjust the rear view mirror, simply operate the control lever.

Type A

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de–icer to free the mirror.

Type B

2001 TACOMA (OM35766U)

101

’01 Tacoma U (L/O 0009)

—Folding rear view mirrors (except lever type)

Anti–glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

for parking

The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.

in

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

102

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

Sun visors

CAUTION

Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti–glare inside rear view mirror and obstruct the rear view.

To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). If glare comes from obliquely behind you, extend the plate at the end of the visor (position 3).

2001 TACOMA (OM35766U)

103

’01 Tacoma U (L/O 0009)

104

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

SECTION 1– 4

OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Interior lights Personal lights Windshield wipers and washer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106
107
108
108
109
110

2001 TACOMA (OM35766U)

105

’01 Tacoma U (L/O 0009)

To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn to full intensity for driving at night.

Headlights and turn signals

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, tail, license plate and instrument panel lights Position 2—Headlights and all of above

the

The lights automatically turn off when the driver’s door is opened with the ignition turned off. To turn the lights on again, turn the key to the “ON” position or turn the headlight switch off, then on again. The lights also automatically turn off if they are left on for 30 minutes with the ignition switch off. If you are going to park for over one week, make sure the headlight switch is off.

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

Daytime running light system (all mod- els in Canada and some models in the U.S.A.) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off.

the

106

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

Emergency flashers

High–Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

2001 TACOMA (OM35766U)

107

’01 Tacoma U (L/O 0009)

Instrument panel light control

Interior lights

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

To adjust the brightness of the instru- ment panel lights, turn the knob.

Front light (regular cab models)

108

2001 TACOMA (OM35766U)

Rear light (Xtra–cab and double cab mod- els)

To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the doors are opened. The light goes off when all the doors are closed. Vehicles without the power door lock sys- tem— To prevent from being dis- charged, the light will automatically turn off if the door is left open for 30 minutes with the switch at the “DOOR” position. Vehicles with the power door tem— To prevent from being dis- charged, the light will automatically turn off after 30 minutes in the following cases. (cid:1) The light is left at the “ON” position. (cid:1) The door is left open with the switch

the battery

the battery

lock sys-

at the “DOOR” position.

’01 Tacoma U (L/O 0009)

light comes on when any door

ILLUMINATED ENTRY SYSTEM With the switch at the “DOOR” position, the is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: (cid:1) All the doors are closed when the igni- tion key is in the “ACC” or “ON” posi- tion.

(cid:1) All the doors are closed and locked. (with power door lock system models only)

Vehicles with the power door tem— When any door is unlocked or the key is removed, the light comes on for 15 sec- onds, even if the door is not opened.

lock sys-

Personal lights

The personal lights operate separately with each outer switch. To turn on the light, push the switch on your side. To turn the light off, push the switch once again. To prevent from being dis- charged, the light will automatically turn off after 30 minutes.

the battery

2001 TACOMA (OM35766U)

109

’01 Tacoma U (L/O 0009)

Windshield wipers and washer (intermittent type)

Windshield wipers and washer (mist type)

To squirt washer fluid, pull the lever toward you and release it. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Slow

Fast

the windshield,

For a single sweep of push the lever up and release it. To squirt washer fluid, pull the lever toward you and release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7–3.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.

the band upward to

110

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

2001 TACOMA (OM35766U)

111

’01 Tacoma U (L/O 0009)

112

2001 TACOMA (OM35766U)

’01 Tacoma U (L/O 0009)

SECTION 1– 6

OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission Manual transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four–wheel drive system Rear differential lock system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clutch start cancel switch

122
123
128
130
134
136
137
139

2001 TACOMA (OM35766U)

121

’01 Tacoma U (L/O 0009)

Ignition switch with steering lock

You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be in the “P” posi- tion before pushing the key. When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.

CAUTION

For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.

NOTICE

Do not leave the key in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.

2001 TACOMA (OM35766U)

“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or