2000 Toyota Tacoma Owners Manual

retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor. When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” in this section.) To free the belt again, fully retract the belt and then pull the belt out once more.

then

is

Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment, make sure the anchor is locked in position.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

28

’00 Tacoma(U)

CAUTION

Take up slack

Too high

lap

(cid:1) High- positioned

belts

and loose- fitting belts both could cause serious injuries due to sliding un- der the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

Keep as low on hips as possible

(cid:1) For your safety, do not place the

shoulder belt under your arm.

the

lap and

the position of

Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.

To release the belt, press the buckle- re- lease button and allow the belt to re- tract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.

29

’00 Tacoma(U)

—Front center seat belt

Lengthen

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

Too high

Adjust to a snug fit

Keep as low on hips as possible

Remove excess length of the belt and adjust the belt position. To shorten the belt, pull the free end of the belt. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit.

CAUTION

High- positioned and loose- fitting lap belts could cause serious injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

Sit up straight and well back in the seat. To fasten your belt, insert the tab into the buckle. You will hear a click when the tab locks into the buckle. If the belt is not long enough for you, hold the tab at a right angle to the belt and pull on the tab.

30

’00 Tacoma(U)

—Stowing the rear seat buckles

To release the belt, press the buckle- re- lease button.

The buckles can be fixed when not in use. When taking out the buckle from the hold- er, pull on the belt webbing to remove the buckle from the lower portion.

from your Toyota dealer

—Seat belt extender If your seat belt cannot be fastened se- curely because it is not long enough, a personalized seat belt extender is avail- able free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender. Bring the heaviest coat you expect to wear for prop- er measurement and selection of length. Additional ordering information is available at your Toyota dealer.

CAUTION

When using the seat belt extender, observe the following. Failure to fol- low these instructions could result in less effectiveness of the seat belt re- straint system in case of vehicle acci- dent, increasing the chance of per- sonal injury. (cid:1) Never use the seat belt extender if you can fasten the seat belt without it.

31

’00 Tacoma(U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the seat belt extender is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

(cid:1) Remember that the extender pro- vided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one origi- nally intended for.

To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the “PRESS” signs on the buckle- release buttons of the ex- tender and the seat belt are both facing outward as shown. You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle- release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extend- er itself. When not and store in the vehicle for future use.

in use, remove the extender

32

’00 Tacoma(U)

—Front seat belt pretensioners

The driver and front passenger’s seat belt pretensioners are designed to be activated in response to a severe fron- tal impact. When the airbag sensor detects the shock of a severe frontal impact, the front seat belt is quickly drawn back in by the re- tractor so that the belt snugly restrains the front seat occupants. The seat belt pretensioners are activated even with no passenger in the front seat. Collisions occurring at certain speeds and angles may cause the seat belt preten- sioners and SRS airbags not to operate all together.

This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the front seat belt pretensioners are operating proper- ly. This warning the airbag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, warning interconnecting wiring and power sources. (For details, see “Service reminder indicators and warning buzzers” in Section 1- 5.)

light system monitors

light,

The seat belt pretensioner system mainly consists of the following components and their locations are shown in the illustra- tion. 1. Front airbag sensors 2. SRS warning light 3. Seat belt pretensioner assemblies 4. Airbag sensor assembly The seat belt pretensioner is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.

33

’00 Tacoma(U)

When a seat belt pretensioner is acti- vated, an operating noise may be heard and a small amount of smoke- like gas may be released. This gas is harmless and does not indicate that a fire is occur- ring. Once the seat belt pretensioner has been activated, the seat belt retractor remains locked.

CAUTION

Do not modify, remove, strike or open the front seat belt pretensioner as- semblies, airbag sensor or surround- ing area or wiring. Doing any of these may cause sudden operation of the front seat belt pretensioners or disable the system, which could re- sult in death or serious personal inju- ry. Failure to follow these instructions can result in death or serious inju- ries.

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the seat belt pretensioners in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Repairs on or near the front seat

belt pretensioner assemblies

(cid:1) Modification of the suspension sys-

tem

(cid:1) Modification of the front end struc-

ture

(cid:1) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:1) Repairs made on or near the front fenders, front end structure or con- sole

34

the

following conditions occurs,

This front seat belt pretensioner system has a service reminder indicator to inform the driver of operating problems. If either of this indicates a malfunction of the airbags or pretensioners. Contact your Toyota dealer as soon as possible the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or remains on.

to service

(cid:1) The light comes on or flashes while

driving.

(cid:1) If either front seat belt does not retract or can not be pulled out due to a malfunction or activation of the preten- sioner.

(cid:1) The front seat belt pretensioner assem- bly or surrounding area has been dam- aged.

(cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that did not cause the seat belt pretensioners to operate.

(cid:1) The front seat belt pretensioner assem- bly is scratched, cracked, or otherwise damaged.

’00 Tacoma(U)

SRS driver and front passenger airbags

The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide further protection for occupants in the following seats in addition to the prima- ry safety protection provided by the seat belts. (cid:1) Models with separate front seats—The SRS airbags are designed to protect the driver and front passenger.

(cid:1) Models with bench

front seats—The SRS airbags are designed to protect the driver and right- front passenger. They are not designed to protect occu- pant in the center position.

In response to a severe frontal impact, the SRS airbags work together with the seat belts to help prevent or reduce injury by inflating. The SRS airbags help to re- duce injuries mainly to the driver’s or front passenger’s head or chest directly hitting the steering wheel or dashboard. When the passenger airbag manual on- off switch is in the “ON” position, the passenger air- bag is activated even with no passenger in the front seat. Be sure to wear your seat belt.

CAUTION

A driver or front passenger too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: (cid:1) The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.

(cid:1) The front passenger sit as far back

as possible from the dashboard.

(cid:1) All vehicle occupants be properly restrained using the available seat belts.

35

’00 Tacoma(U)

CAUTION

(cid:1) Make sure that the indicator light is

off.

(cid:1) Do not turn off the passenger air- bag manual on- off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the right front passenger seating position.

(cid:1) When the passenger airbag manual on- off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.

airbag

system

passenger

The is equipped with a manual on- off switch and indicator light. Turning the passen- ger airbag manual on- off switch clock- wise to the “ON” position makes the passenger airbag system operational. Turning the passenger airbag manual on- off switch counterclockwise to the “OFF” position disables the passenger airbag system. The indicator light on the passenger airbag manual on- off switch will come on when the passen- ger airbag system has been disabled. See switch” in this section for detail.

“Passenger airbag manual on- off

36

’00 Tacoma(U)

TABLE 1: A PASSENGER RISK GROUP

Infant. An infant (less than 1 year old) who must ride in the front seat because: (cid:1) Vehicle has no rear seat; (cid:1) Vehicle has a rear seat too small to accommodate a rear- facing infant seat;

or

(cid:1) The infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can constantly monitor the child’s condition.

Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: (cid:1) Vehicle has no rear seat: (cid:1) Although children ages 1 to 12 ride in the rear seat(s) whenever possible,

children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of vehicle; or

(cid:1) The child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.

Medical condition. A passenger has a medical condition which according to his or her physician: (cid:1) Causes the passenger airbag to pose a special risk for the passenger: and (cid:1) Makes the potential harm from the passenger airbag in a crash greater than the potential harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard, or windshield in a crash.

For more detailed information concerning about the passenger risk group, please contact NHTSA at 1- 800- 424- 9393 or Transport Canada at 1- 800- 333- 0371.

This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” in Section 1- 5.)

light system monitors

remainder

“Service

37

’00 Tacoma(U)

this

However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the nose of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It is possible that in some collisions at the lower zone of airbag sensor detection and activation the SRS airbags and seat belt pretensioners will not operate all together. For the safety of all occupants, always wear your seat belts.

Collision from the rear

Collision from the side

Vehicle rollover

The SRS airbags are not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision.

The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when impacting straight into a fixed barrier that does not move or deform. If the severity of the impact is below the above threshold the SRS airbags may not deploy.

level,

38

’00 Tacoma(U)

Hitting a curb, edge of pavement or hard material

Falling into or jumping over a deep hole

Landing hard or vehicle falling

The SRS airbags may deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

The SRS airbag system consists mainly of the following components, and their loca- tions are shown in the illustration. 1. Front airbag sensors 2. Airbag module for driver

(airbag and inflator)

3. Passenger airbag manual on- off switch 4. Airbag module for passenger

(airbag and inflator)

5. Airbag sensor assembly 6. SRS warning light The airbag sensor assembly consists of a safing sensor and airbag sensor.

the

fills

inflators quickly

In a severe frontal impact, sensors detect deceleration and the system triggers the airbag inflators. Then a chemical reaction in the airbags with non- toxic gas to help restrain the forward motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non- toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.

39

’00 Tacoma(U)

CAUTION

(cid:1) The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and front passenger side seat belt sys- tems. The front seat occupants can be killed or seriously injured by an inflating airbag if they do not wear the available seat belts. During sud- den braking just before a collision, an unrestrained driver or front pas- senger can move forward into direct contact with or close proximity to the airbag which may then deploy during the collision. To ensure max- imum protection in an accident, the driver and all passengers in the ve- hicle must wear their seat belts. Wearing a seat belt during an acci- dent reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts” in this section.

(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint system. As to double cab models, Toyota recommends that all infants and children be placed in the rear seat of the vehicle and properly restrained. The rear seat is the safest for infants and children. For the installation of a child restraint sys- tem, see “Child restraint” in this section.

instructions concerning

the windshield as

A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.

40

CAUTION

A member of a passenger risk group should never sit or be occupied in the right front passenger seat with airbag manual on- off switch in the “ON” position. (For details, see “SRS driver and front passenger airbags” in this section.)

’00 Tacoma(U)

CAUTION

(cid:1) Never put a rear- facing child re- straint system on the right front seat with the passenger airbag manual on- off switch in the “ON” position. In the event of an acci- dent, the force of the rapid inflation of the passenger airbag can cause death or serious injury to the child.

(cid:1) A forward- facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on- off switch in the “ON” position, because the force of a deploying airbag could cause death or serious injury to the child in forward seating position. For the installation of a child restraint sys- tem, see “Child restraint” in this section.

instructions concerning

41

’00 Tacoma(U)

(cid:1) Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or serious- ly injured. Sit up straight and well back in the seat, and always use your seat belt.

(cid:1) Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag inflates with con- siderable speed and force; the child may be killed or seriously injured. (cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” in this section.

(cid:1) Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the airbag system. They might restrict inflation or cause death or serious injury as they are projected rear- ward by the force of deploying air- bags. Likewise, the driver and front passenger should not hold things in their arms or on their knees.

42

(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components, such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS airbag inflation or disable the system, which could result in death or serious injury. instructions Failure to follow these can result in death or serious injury.

’00 Tacoma(U)

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Modification of the suspension sys-

tem

(cid:1) Modification of the front end struc-

ture

(cid:1) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:1) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag

This SRS airbag system has a service reminder indicator to inform the driver of operating problems. If either of the follow- ing conditions occurs, indicates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on.

this

(cid:1) The light comes on while driving.

43

’00 Tacoma(U)

Passenger airbag manual on- off switch

Indicator light

This on- off switch is designed to dis- able the passenger airbag in order to allow usage, if necessary, of a member of a passenger risk group identified in TABLE 1 is occupying the right front passenger seating position. (For details, see “SRS driver and front passenger airbags” in this section.) Operate on- off switch as follows: Insert key into the keyhole and turn it. To turn passenger airbag on: Turn the key clockwise to the “ON” position. To turn passenger airbag off: Turn the key counterclockwise to the “OFF” position. The indicator comes on when the passen- ger airbag system is off.

CAUTION

(cid:1) Make sure that the indicator light is

off.

(cid:1) Do not turn off the passenger air- bag manual on- off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the right front passenger seating position.

(cid:1) When the passenger airbag manual on- off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.

For details, see “SRS driver and front passenger airbags” in this section.

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS airbags have been inflated. (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS airbags to inflate.

front

(cid:1) The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.

passenger

airbag

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

44

Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the seat and must be restrained using the vehicle’s seat belt. See “Seat belts” for details.

CAUTION

(cid:1) For effective protection in automo- bile accidents and sudden stops, children must be properly re- strained using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a sub- stitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s inte- rior.

’00 Tacoma(U)

(cid:1) NORMAL- CAB MODELS—

Toyota strongly urges use of a proper child restraint system which conforms to the size of the child. XTRA- CAB MODELS— Toyota strongly urges use of a proper child restraint system which conforms to the size of the child and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on- off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.)

force of

the

(cid:1) Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.

child

the

by

45

When not using the child restraint system, keep it secured with the seat belt. This will prevent it from injuring passengers in the event of a sudden stop or accident.

’00 Tacoma(U)

CAUTION

the

force of

(cid:1) Never put infant or child age 1 to 12 in a passenger risk group on the right front seat with the passenger airbag manual on- off switch in the “ON” position. In the event of an accident, the rapid inflation of the passenger airbag can cause death or serious injury to the child. If you must put infant or child age 1 to 12 in a passenger risk group on the right front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on. (For details, see “SRS driver and front passenger airbags” in this section.) installing the child restraint system, make sure it is secured in place according to the manufactur- er’s is not re- instructions. strained securely, it may cause death or serious injury to the child in the event of a sudden stop or accident.

(cid:1) After

If

it

the manufacturer’s

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with either the lap belt or the lap portion of the lap/ shoulder belt. You must carefully con- sult instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer of the system. General directions are also provided under the fol- lowing illustrations. The child restraint system should be installed on the rear seat if your vehicle is equipped with rear seats. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.

46

’00 Tacoma(U)

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.

(A) Infant seat

(C) Booster seat

(B) Convertible seat

47

—Installation with 2- point type seat belt

’00 Tacoma(U)

the child restraint system

With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion. Split bench seat— Adjust the passenger’s seat forward and rearward travel as well as seatback posi- tion so that the child restraint system is securely restrained.

(A) INFANT SEAT INSTALLATION An infant seat is used in rear- facing position only.

CAUTION

CAUTION

Ignoring the above instructions may result in a serious injury in case of an accident.

airbag manual

Never put a rear- facing child restraint system on the front seat with the passenger on- off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger air- bag can cause death or serious injury to the child.

48

’00 Tacoma(U)

CAUTION

If you must put a rear- facing child restraint system on the front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on.

When you put a rear- facing child re- straint system on the front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

1. Run

the

lap belt

the center

infant seat

through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.

following

49

’00 Tacoma(U)

2. While pressing the infant seat

firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

50

’00 Tacoma(U)

the child restraint system

With the child restraint system installed, check that your driving position is satis- factory and that the child restraint system does not interfere with your driving. If your driving position is not satisfactory, or interferes with your driving, install it at another posi- tion. Split bench seat— Adjust forward and rearward travel as well as seatback posi- tion so that the child restraint system is securely restrained.

the passenger seat

3. To remove the infant seat, press the

buckle- release button.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward- facing and rear- facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instructions about the applicable child’s age and size as well as directions for installing a child restraint system.

follow

CAUTION

Ignoring the above instructions may result in a serious injury in case of an accident.

51

’00 Tacoma(U)

CAUTION

If you must put a rear- facing child restraint system on the front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on.

CAUTION

airbag manual

Rear- facing child restraint system: Never put a rear- facing child restraint system on the front seat with the passenger on- off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger air- bag can cause death or serious injury to the child.

When you put a rear- facing child re- straint system on the front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

52

’00 Tacoma(U)

CAUTION

Forward- facing child restraint system: A forward- facing child restraint sys- tem should never be put on the front seat with the passenger airbag manu- al on- off switch in the “ON” position, because the force of a deploying air- bag could cause death or serious in- jury to the child in forward seating position.

1. Run

lap belt

the center

through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.

the convertible seat provided insert the

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

53

’00 Tacoma(U)

2. While pressing

the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.

CAUTION

3. To remove the convertible seat, press

the buckle- release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

54

’00 Tacoma(U)

—Installation with 3- point type seat belt

(A) INFANT SEAT INSTALLATION An infant seat is used in rear- facing position only.

WHEN INSTALLING ON THE REAR SEAT (Xtra- cab models): Raise the bottom cushion before instal- ling the child restraint system. If your child restraint system is too large, you can use the folding table as an auxil- iary support. For instructions about how to stand the table, see “Cup holder (Xtra- cab models)” in Section 1- 9.

CAUTION

Never put a rear- facing child restraint system on the right front seat with the passenger airbag manual on- off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger air- bag can cause death or serious injury to the child.

55

’00 Tacoma(U)

CAUTION

If you must put a rear- facing child restraint system on the right front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on.

CAUTION

(cid:1) Do not put a rear- facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause severe injury to the child and front passenger in case of sudden braking or a colli- sion.

(cid:1) If your driving position is not satis- the child restraint

factory, system at another position.

install

When you put a rear- facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

56

’00 Tacoma(U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

57

’00 Tacoma(U)

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle- release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

58

’00 Tacoma(U)

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward- facing and rear- facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instruction about the applicable child’s age and size as well as directions for installing a child restraint system.

follow

CAUTION

Rear- facing child restraint system: Never put a rear- facing child restraint system on the right front seat with the passenger airbag manual on- off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger air- bag can cause death or serious injury to the child.

When you put a rear- facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position. (For details, see “SRS driver and front passenger airbags” in this section.) The indicator comes on when the system is off.

59

’00 Tacoma(U)

CAUTION

CAUTION

If you must put a rear- facing child restraint system on the right front seat, make sure the passenger airbag manual on- off switch is in the “OFF” position and that the indicator light is on.

Forward- facing child restraint system: A forward- facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on- off switch in the “ON” position, because the force of a deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)

60

CAUTION

(cid:1) Do not put a rear- facing child re- straint system on the rear seat if the child restraint system interferes with the front seat lock mechanism or with your proper driving posi- tion. This can cause severe injury to the child and front passenger in case of sudden braking or a colli- sion.

(cid:1) If your driving position is not satis- the child restraint

factory, system at another position.

install

’00 Tacoma(U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

61

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

’00 Tacoma(U)

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the convertible seat, press the buckle- release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

62

’00 Tacoma(U)

CAUTION

A forward- facing child restraint sys- tem which belongs to a passenger risk group should never be put on the right front seat with the passen- ger airbag manual on- off switch in the “ON” position, because the force of a deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver and front passenger airbags” in this section.)

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward- fac- ing position only.

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

the

tab

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.

63

’00 Tacoma(U)

(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. To remove the child restraint system, press the buckle- release button and al- low the belt to retract.

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

(cid:1) Both high- positioned lap belts and loose- fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

64

’00 Tacoma(U)

Tilt steering wheel

Outside rear view mirrors—

To change the steering wheel angle: Type A—Hold the steering wheel, pull up the lock release lever, tilt the steer- ing wheel to the desired angle and re- lease the lever. Type B—Hold the steering wheel, pull the lock release lever toward you, tilt the steering wheel to the desired angle and release the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

CAUTION

(cid:1) Do not adjust the steering wheel

while the vehicle is moving.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

65

Type A

Type B

’00 Tacoma(U)

—Rear view mirror control (lever type)

—Rear view mirror control (power type)

To adjust the rear view mirror, simply operate the control lever.

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de-icer to free the mirror.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Place the switch at “L” (left) or “R” (right).

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirror can be adjusted when key is in the “ACC” or “ON” position.

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries.

66

’00 Tacoma(U)

—Folding rear view mirrors (except lever type)

Anti- glare inside rear view mirror

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de-icer to free the mirror.

for parking

The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.

in

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

67

’00 Tacoma(U)

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries.

68

’00 Tacoma(U)

SECTION 1- 4

OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Interior lights Personal lights Ignition switch light Windshield wipers and washer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

70
71
72
72
73
73
73

69

’00 Tacoma(U)

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

Daytime running light system (all mod- els in Canada and some models in the U.S.A.) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn to full intensity for driving at night.

the

Headlights and turn signals

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, tail, license plate and instrument panel lights Position 2—Headlights and all of above Light reminder buzzer A buzzer will remind you to turn the lights off when the driver’s door is opened if you remove the key with the headlights left on.

the

70

High- Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

’00 Tacoma(U)

Emergency flashers

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

71

’00 Tacoma(U)

Instrument panel light control

Interior lights

To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when either door is opened. The light goes off when both doors are closed.

To adjust the brightness of the instru- ment panel lights, turn the knob.

Front light

72

Rear light (Xtra- cab models)

’00 Tacoma(U)

Personal lights

Ignition switch light

Windshield wipers and washer (intermittent type)

The personal lights operate separately with each outer switch. To turn on the light, push the switch on your side. To turn the light off, push the switch once again. The center switch has the following posi- tions: Position 1—Turns both lights on when ei- ther door is opened. The lights go off when both doors are closed. Position 2—The lights are off unless you operate either outer switch.

For easy access to the ignition switch, the ignition switch light comes on when either door is opened. The light remains on for some time after both doors are closed.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.

the band upward to

73

In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

’00 Tacoma(U)

Windshield wipers and washer (mist type)

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Slow

Fast

the windshield,

For a single sweep of push the lever up and release it. To squirt washer fluid, pull the lever toward you and release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7- 3.

To squirt washer fluid, pull the lever toward you and release it. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7- 3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

74

’00 Tacoma(U)

SECTION 1- 5

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge Engine coolant temperature gauge Tachometer Odometer and two trip meters Service reminder indicators and warning buzzers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

76
76
77
78
78

75

’00 Tacoma(U)

Fuel gauge

Engine coolant temperature gauge

With tachometer * : On some models

the

The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. This fuel gauge has a non- return type needle which remains at the last indicated position when the ignition switch is turned off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

With tachometer

Without tachometer

76

Without tachometer

’00 Tacoma(U)

Tachometer

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: (cid:1) Driving up a long hill on a hot day. (cid:1) Reducing speed or stopping after high

speed driving.

(cid:1) Idling for a long period with the air conditioning on in stop- and- go traffic.

(cid:1) Towing a trailer.

NOTICE

(cid:1) Do not remove the thermostat in the engine cooling system as this may cause the engine to overheat.