Login- Download PDF Manual
-
1-3. Adjustable components (seats, mirrors, steering wheel)
Third center seat belt
The third center seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation.
Make sure that the buckle is securely latched for ready use of the center seat belt.
the
the
tab with
Matches hooked end (tab “A”) Matches the tab with the con- caved end (tab “B”)
■ Release method
The belt can be completely released when not required, such as when folding down the third seat.
To release the tab “B”, push the buckle release button. To release the tab “A”, insert the key (P. 30) or tab “B” into the hole on the buckle. Retract the belt slowly when releasing and stowing the seat belt.
71
1-3. Adjustable components (seats, mirrors, steering wheel)
Stow the seat belt tabs in the cover set in the roof as shown.
■ Extracting the belt
Pull the belt out partially, and then remove the tabs from the cover.
Seat belt comfort guide (third center seat)
If the shoulder belt sits close to a person’s neck, use the seat belt comfort guide.
Pull the comfort guide from the pocket.
72
1-3. Adjustable components (seats, mirrors, steering wheel)
Slide the belt past the slot of the guide.
The elastic cord must be behind the seat belt.
Seat belt pretensioners (front seats)
The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision or a vehicle rollover.
The pretensioner may not acti- vate in the event of a minor frontal impact, a side impact or a rear impact.
73
1-3. Adjustable components (seats, mirrors, steering wheel)
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
■Automatic locking retractor (ALR)
When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (P. 133)
■Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (P. 69) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.
■People suffering illness
Obtain medical advice and wear the seat belt in the proper way.
74
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (P. 129) ●When the child becomes large enough to properly wear the vehicle’s
seat belt, follow the instructions on P. 69 regarding seat belt usage.
■Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.
■Seat belt extender
If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
they are not
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or serious injury. ■Wearing a seat belt
●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at once, including children.
●Toyota recommends that children be seated in the rear seat and always
use a seat belt and/or an appropriate child restraint system.
75
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Wearing a seat belt
●Do not recline the seat any more than necessary to achieve a proper seat- ing position. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.
■When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfas- tened, scissors should be used to cut the belt.
■Adjustable shoulder anchor
Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (P. 70)
■Seat belt pretensioners
●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.
●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
■Seat belt damage and wear
●Do not damage the seat belts by allowing the belt, plate, or buckle to be
jammed in the door.
●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belt cannot protect an occupant from death or serious injury.
76
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat belt damage and wear
●Ensure that the belt and tab are locked and the belt is not twisted.
If the seat belt does not function correctly, immediately contact your Toyota dealer.
●Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there is no obvious damage.
●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.
■When using the third center seat belt
Do not use the third center seat belt with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking or a collision.
■Using a seat belt comfort guide (third center seat)
●Make sure the belt is not twisted and that it lies flat. The elastic cord must
be behind the belt and the guide must be on the front.
●To reduce the chance of injury in case of a sudden stop, sudden swerve or accident while driving, remove and store the comfort guide in its pocket when it is not in use.
●Always make sure the shoulder belt is positioned across the center of the shoulder. The belt should be kept away from the neck, and should not slide off the shoulder. Failure to observe these precautions could reduce the effectiveness of the seat belt in an accident, causing death or serious injury.
77
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Using a seat belt extender
●Do not wear the seat belt extender if you can fasten the seat belt without
the extender.
●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.
NOTICE
■When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
78
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (manually adjustable type)
The steering wheel can be adjusted to a comfortable position.
Hold the steering wheel and press the lever down.
Adjust to the ideal position by moving the steering wheel horizontally and vertically.
After adjustment, pull the lever up the steering wheel.
to secure
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
■After adjusting the steering wheel
Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident and resulting in death or serious injury.
79
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel (power-adjustable type)
The steering wheel can be adjusted to a comfortable position.
Up Down Toward the driver Away from the driver
Auto tilt away
When the key is removed from the engine switch, the steering wheel returns to its stowed posi- tion by moving up and away to enable easier driver entry and exit.
Inserting the key into the engine switch returns the steering wheel to its original position.
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
80
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror
Glare from the headlights of vehicles behind can be reduced by using the following functions.
Manual anti-glare inside rear view mirror
Normal position Anti-glare position
81
1-3. Adjustable components (seats, mirrors, steering wheel)
Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and automatically reduces the reflected light.
Turns automatic mode ON/ OFF
The indicator comes on when automatic mode is turned on. The mirror will revert to the automatic mode each time the engine switch is turned on.
Adjusting the height of rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
82
1-3. Adjustable components (seats, mirrors, steering wheel)
■To prevent sensor error (vehicles with auto anti-glare inside rear view
mirror)
To ensure that the sensors operate prop- erly, do not touch or cover them.
■If a sun visor interferes with the mirror
Hold and rotate the mirror to adjust the support.
CAUTION
■Caution while driving
Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
83
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors
Mirror angle can be adjusted using the switch when the engine switch is in the ACC or ON position.
Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down, in or out using the switch.
Folding back the mirrors
From outside
Push the mirrors towards the back of the vehicle to fold them.
84
1-3. Adjustable components (seats, mirrors, steering wheel)
From inside (if equipped)
Press the switch.
Pressing again will unfold the mir- rors.
Linked mirror function when reversing (if equipped)
Press the switch to turn on/off linked mirror function.
tilt
The outside rear view mirrors will automatically downwards when the vehicle is in reverse, in order to give a better view of ground.
85
1-3. Adjustable components (seats, mirrors, steering wheel)
■When the mirrors are fogged up (vehicles with outside rear view mirror
defoggers) Turn on the mirror defoggers to defog the mirrors. (P. 307)
■Automatic adjustment of the mirror angle (vehicles with driving posi-
tion memory) A desired mirror face angle can be entered to memory and recalled automat- ically by the driving position memory. (P. 62)
■Auto anti-glare function (if equipped)
When the anti-glare inside rear view mirror is set to automatic mode, the out- side rear view mirrors will activate in conjunction with the anti-glare inside rear view mirror to reduce reflected light. (P. 81)
CAUTION
■When driving the vehicle
Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded back. ●Both the driver and passenger side mirrors must be extended and properly
adjusted before driving. ■When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■When the mirror defoggers are operating (vehicles with outside rear
view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
86
1-3. Adjustable components (seats, mirrors, steering wheel)
NOTICE
■If the mirrors are frozen
Do not operate the control or scrape the mirror faces. Use a spray de-icer to free the mirror.
87
1-3. Adjustable components (seats, mirrors, steering wheel) Roof luggage carrier
Roof rails Cross rails
Adjustment the position of cross rails
Turn the knobs counterclockwise to loosen the cross rails.
Slide the cross rails to the appro- priate position for loading lug- gage.
After adjusting, be sure to tighten the cross rails by turning knobs clockwise.
88
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Cross rail adjustment
Make sure the cross rails are locked securely by applying pressure forward and rearward. Failure to do so may cause an accident, death or serious injury in the event of emergency braking or a collision.
■When loading cargo
Observe the following precautions: ●Place the cargo so that its weight is distributed evenly between the front
and rear axles.
●If loading long or wide cargo, never exceed the vehicle overall length or
width. (P. 512)
●Before driving, make sure the cargo is securely fastened to the roof lug-
gage carrier.
●Loading cargo on the roof luggage carrier will raise the vehicle’s center of gravity. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise unexpected loss of control or vehicle rollover may occur.
●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle occasionally during the trip to make sure the cargo remains securely fastened.
●Do not exceed 150 lb. (68 kg) cargo weight on the roof luggage carrier.
NOTICE
■When loading the luggage
Be careful not to scratch the surface of the moon roof.
89
1-4. Opening and closing the windows and moon roof Power windows
The power windows can be opened and closed using the following switches.
Closing One-touch closing (Front windows only)* Opening One-touch opening (Front windows only)*
*: To stop the window partway, operate the switch in the oppo- site direction.
Press the switch down to lock passenger window switches and back window switch.
Use this switch to prevent chil- dren from accidentally opening or closing a passenger window and back window.
Lock switch
90
1
1-4. Opening and closing the windows and moon roof
■The power windows can be operated when
The engine switch is in the ON position.
■Door lock linked power windows operation
The power windows can be opened and closed using the key. (P. 35)
■Operating the power windows after turning the engine switch off
The power windows can be operated for approximately 43 seconds even after the engine switch is turned to the ACC position or turned off. They can- not, however, be operated once either front door is opened.
■Jam protection function (Front windows only)
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
■When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the front door. ●After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the ON position.
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
91
1-4. Opening and closing the windows and moon roof
■Customization that can be configured at Toyota dealer
Settings (e.g. power windows) can be changed. (Customizable features P. 539)
CAUTION
■Closing the windows
Observe the following precautions. Failing to do so may result in death or serious injury. ●The driver is responsible for all the power window operations, including the operation for the passengers. In order to prevent accidental operation, especially by a child, do not let a child operate the power windows. It is possible for children and other passengers to have body parts caught in the power window. Also, when riding with a child, it is recommended to use the window lock switch. (P. 90)
●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●When using the key and operating the power windows, operate the power window after checking to make sure that there is no possibility of any pas- senger having any of their body parts caught in the window. Also do not let a child operate window by the key. It is possible for children and other pas- sengers to get caught in the power window.
●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the window fully closes.
92
1-4. Opening and closing the windows and moon roof Power back window
The power back window can be opened and closed using the switch and key.
From inside
One-touch closing*1,*2
Closing One-touch opening*1
Opening *1:Pressingthe switch
the opposite direction will stop win- dow travel partway.
in
*2:During off-road traveling, the
one-touch closing operation may be deactivated depend- ing on the vehicle speed and road surface conditions. At that time, close the window using the normal closing operation
From outside
Opening Closing Turn the key fully and hold it.
93
1-4. Opening and closing the windows and moon roof
■The power back window can be operated when
●The engine switch is in the ON position. ●The power back window can be opened when the rear window wiper is working. At that time, the wiper stops working until the window is closed again. If the rear window is not fully closed, the rear window wiper, washer, and defogger will not work.
■Operating the power back window after turning the engine switch off
The power back window can be operated for approximately 43 seconds even after the engine switch is turned to the ACC position or turned off. It cannot, however, be operated once either front door is opened.
■Jam protection function
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly. ■When the power back window does not close normally
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power back window switch. ●After stopping the vehicle, the window can be closed by holding the power back window switch in the one-touch closing position while the engine switch is turned to the ON position.
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.
Hold the power back window switch in the one-touch closing posi- tion. Continue holding the switch for a further 6 seconds after the window has closed. Hold the power back window switch in the one-touch opening posi- tion. Continue holding the switch for a further 2 seconds after the window has opened completely. Hold the power back window switch in the one-touch closing posi- tion once again. Continue holding the switch for a further 2 seconds after the window has closed.
94
1-4. Opening and closing the windows and moon roof
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
■Customization that can be configured at Toyota dealer
Settings (e.g. power back window) can be changed. (Customizable features P. 539)
CAUTION
■Closing the power back window Observe the following precautions. Failing to do so may result in death or serious injury. ●The driver is responsible for all the power back window operations, includ- ing the operation for the passengers. In order to prevent accidental opera- tion, especially by a child, do not let a child operate the power back window. It is possible for children and other passengers to have body parts caught in the power back window. Also, when riding with a child, it is rec- ommended to use the window lock switch. (P. 90)
●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●When using the key and operating the power back window, operate the power back window after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the window. Also do not let a child operate window by the key. It is possible for children and other passengers to get caught in the power back window.
●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the window fully closes.
95
1-4. Opening and closing the windows and moon roof Moon roof
Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing
Open The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof. To stop partway, press the switch lightly. Close To stop partway, press the switch lightly.
Tilt up Tilt down To stop partway, press the switch lightly.
■ Tilt up and down
96
: If equipped
1
1-4. Opening and closing the windows and moon roof
■The moon roof can be operated when The engine switch is in the ON position. ■Door lock linked moon roof operation
The moon roof can be opened and closed using the key. (P. 35)
■Operating the moon roof after turning the engine switch off
The moon roof can be operated for approximately 43 seconds even after the engine switch is turned to the ACC or turned off. It cannot, however, be oper- ated once either front door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.
■When the moon roof does not close normally
Perform the following procedure: ●If the moon roof closes but then re-opens slightly
Stop the vehicle. Press and hold the “SLIDE” switch.*1
The moon roof will close, reopen and pause for approximately 10
seconds.*2 Then it will close again, tilt up and stop. Check to make sure that the moon roof is completely stopped and then release the switch. *1:If the switch is released at the incorrect time, the procedure willhave to be performed again from the beginning.
*2:If the switch is released after the above mentioned 10 seconds pause, automatic operation will be disabled. In that case, press and hold the “SLIDE” or “TILT” switch, and the moon roof will tilt up and stop. Check to make sure that the moon roof is com- pletely stopped and then release the switch.
If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
97
1-4. Opening and closing the windows and moon roof
■To reduce wind noise
When the moon roof is opened automatically, it will stop slightly before the full open position. Driving with the moon roof in this position can help reduce wind noise. ■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.
■Moon roof open reminder function
An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off.
■Customization that can be configured at Toyota dealer
Settings (e.g. moon roof) can be changed. (Customizable features P. 539)
98
1
1-4. Opening and closing the windows and moon roof
CAUTION
■Opening the moon roof
Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
●Do not sit on top of the moon roof.
■Closing the moon roof
Observe the following precautions. Failing to do so may result in death or serious injury. ●The driver is responsible for moon roof opening and closing operations. In order to prevent accidental operation, especially by a child, do not let a child operate the moon roof. It is possible for children and other passen- gers to have body parts caught in the moon roof.
●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.
●When using the key and operating the moon roof, operate the moon roof after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the moon roof. Also do not let a child operate moon roof by the key. It is possible for children and other passengers to get caught in the moon roof.
●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the moon roof fully closes.
99
1-5. Refueling Opening the fuel tank cap
Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle
● Turn the engine switch to the LOCK position and ensure that
all the doors and windows are closed.
● Confirm the type of fuel. (P. 515)
■ Opening the fuel tank cap
Open the fuel filler door.
Turn the fuel tank cap slowly to open.
100
1-5. Refueling
Hang the fuel tank cap on the back of the fuel filler door.
Closing the fuel tank cap
After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
101
1-5. Refueling
■Fuel types (P. 515)
■E85 Fueling Stations (Flex-fuel engine)
E85 fueling stations and fuel pumps can be identified by the indication “E85
85% Ethanol”. For more information about fueling stations, please refer to the U.S. Department of Energy Web site. http://www.afdc.energy.gov/afdc/locator/stations/■Refueling (Flex-fuel engine)
Observe the following precautions when switching fuels, in order to maintain starting and driving performance. ●Do not change fuels when the fuel level is 1/4 or less. ●Always add at least 2.6 gal. (10 L) of fuel. ●After filling up with fuel, warm up the engine or drive the vehicle for at
least 5 minutes or 7 miles (11 km).
●Do not accelerate rapidly immediately after refueling.
■Fuel tank opening for unleaded gasoline
To help prevent incorrect fueling, your vehicle has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.
102
1
1-5. Refueling
CAUTION
■When refueling the vehicle
Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.
●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury.
●Do not allow anyone that has not discharged static electricity from their
body to come close to an open fuel tank.
●Do not inhale vaporized fuel.
Fuel contains substances that are harmful if inhaled.
●Do not smoke while refueling the vehicle.
Doing so may cause the fuel to ignite and cause a fire.
●Do not return to the vehicle or touch any person or object that is statically
charged. This may cause static electricity to build up, resulting in a possible ignition hazard.
■When refueling
Observe the following precautions to prevent fuel overflowing from the fuel tank: ●Securely insert the fuel nozzle into the fuel filler neck ●Stop filling the tank after the fuel nozzle automatically clicks off ●Do not top off the fuel tank.
■When replacing the fuel tank cap
Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
103
1-5. Refueling
NOTICE
■Refueling
Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface.
■E85 fuel
E85 fuel can be used only in flex-fuel vehicles. Do not add E85 fuel to a gas- oline-engine vehicle. Filling a gasoline-engine vehicle with E85 fuel will have a negative impact on starting and driving performance and will cause damage to the fuel system components.
104
1
1-6. Theft deterrent system Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. This system is designed to help prevent vehicle theft but does not guarantee absolute security against all vehicle thefts.
The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed.
■System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
■Conditions that may cause the system to malfunction
●If the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle
■Certifications for the engine immobilizer system
For vehicles sold in the U.S.A.
FCC ID: MOZRI-42BTY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
105
1-6. Theft deterrent system
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For vehicles sold in Canada
This device complies with Industry Canada licence-exempt RSS stan- dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.
NOTICE
■To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
106
1
1-6. Theft deterrent system Alarm
The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm
The alarm is triggered in the following situations when the alarm is set. ● A locked door is unlocked or opened in any way other than using the wireless remote control door lock function or key. The doors will lock again automatically.
● The hood is opened. ● Vehicles with the glass breakage sensor (if equipped): The
side windows are tapped or broken.
● The battery is reconnected.
■ Setting the alarm system
Close the doors and hood, and lock all the doors. The system will be set automati- cally after 30 seconds.
indicator
The light changes from being on to flashing when the system is set.
■ Deactivating or stopping the alarm
● Unlock the doors. ● Turn the engine switch to the ACC or ON position, or start the
engine. (The alarm will be deactivated or stopped after a few sec- onds.)
107
1-6. Theft deterrent system
■System maintenance
The vehicle has a maintenance-free type alarm system.
■Items to check before locking the vehicle
To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ●Nobody is in the vehicle. ●The windows and moon roof are closed before the alarm is set. ●No valuables or other personal items are left in the vehicle.
■Triggering of the alarm
The alarm may be triggered in the following situations. (Stopping the alarm deactivates the alarm system.)
●A person inside the vehicle opens a
door or hood.
●The battery is recharged or replaced
when the vehicle is locked.
■Panic mode
P. 32
■When the battery is disconnected Be sure to cancel the alarm system. If the battery is discharged before canceling the alarm, the system may be triggered when the battery is reconnected.
108
1-6. Theft deterrent system
■Alarm-operated door lock
In the following cases, depending on the situation, the door may automati- cally lock to prevent improper entry into the vehicle: ●When a person remaining in the vehicle locks the door and the alarm is
activated.
●While the alarm is activated, a person remaining in the vehicle unlocks
the door.
●When recharging or replacing the battery.
NOTICE
■To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
109
1-7. Safety information Correct driving posture
Drive in a good posture as follows:
and to
Sit upright and well back in the seat. (P. 48) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (P. 48) Adjust the seatback so that the controls are easily oper- able. Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (P. 79, 80) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (P. 65) Wear the seat belt correctly. (P. 69)
110
1-7. Safety information
CAUTION
■While driving
●Do not adjust the position of the driver’s seat while driving.
Doing so could cause the driver to lose control of the vehicle.
●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
●Do not place anything under the front seats except for putting them in the
auxiliary box. Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent. The adjustment mechanism may also be damaged.
■Adjusting the seat position
●Do not recline the seat more than necessary when the vehicle is in motion,
to reduce the risk of sliding under the lap belt. If the seat is too reclined during an accident, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury.
●Take care when adjusting the seat position to ensure that other passen-
gers are not injured by the moving seat.
●Do not put your hands under the seat or near the moving parts to avoid
injury. Fingers or hands may become jammed in the seat mechanism.
111
1-7. Safety information SRS airbags
The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
SRS front airbags SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components. SRS knee airbags Can help provide driver and front passenger protection. SRS side and curtain shield airbags SRS side airbags Can help protect the torso of the front seat occupants. SRS curtain shield airbags ● Can help protect primarily the head of occupants in the outer
seats.
● Can prevent the occupants from being thrown from the vehi-
cle in the event of vehicle rollover.
112
Airbag system components
1-7. Safety information
Curtain shield airbag sen- sors SRS warning light Driver’s seat position sen- sor Driver airbag Driver’s seat belt buckle switch Seat belt pretensioners and force limiters
Side airbags AIR BAG ON and AIR BAG OFF indicator lights Curtain shield airbags Front passenger airbag Knee airbags Side and curtain shield air- bag sensors Front airbag sensors Airbag sensor assembly Front passenger’s seat belt buckle switch Front passenger occupant classification system (ECU and sensors)
113
1-7. Safety information
Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants.
■SRS warning light
This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensor assemblies, curtain shield air- bag sensor assemblies, driver’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system (ECU and sensors), AIR BAG ON and AIR BAG OFF indicator lights, front passenger’s seat belt buckle switch, front seat belt pretensioner assemblies, airbags, interconnecting wiring and power sources. (P. 470)
■If the SRS airbags deploy (inflate)
●Slight abrasions, burns, bruising etc., may be sustained from SRS air- bags, due to the extremely high speed deployment (inflation) by hot gases.
●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, and parts of the front and rear pillars and roof side rail, may be hot for several minutes. The airbag itself may also be hot.
●The front windshield may crack.
114
1
1-7. Safety information
■Operating conditions (front airbags)
●The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12-18 mph [20-30 km/h] frontal collision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under the bed of a truck, etc.).
●Depending on the type of collision, it is possible that only the seat belt
pretensioners will activate.
●The SRS front airbags for the front passenger will not activate if there is no passenger sitting in the front passenger seat. However, the SRS front airbags for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied. (P. 124)
■Operating conditions (side airbags & curtain shield airbags)
The SRS side airbags & SRS curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corre- sponding to the impact force produced by an approximately 3300 lb. [1500
kg] vehicle colliding with the vehicle cabin from a direction perpendicular to the vehicle orientation at an approximate speed of 12-18 mph [20-30 km/h]).■Operating conditions (curtain shield airbags)
The SRS curtain shield airbags are designed to inflate when the passenger compartment is subjected to a severe impact from the side or vehicle roll- over. Depending on the conditions and type of accident, there are times when the curtain shield airbags may deploy (inflate) in a front impact.
115
1-7. Safety information
■Conditions under which the SRS airbags may deploy (inflate), other
than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.
●Hitting a curb, edge of pavement or
hard surface
●Falling into or jumping over a deep hole ●Landing hard or vehicle falling
The SRS curtain shield airbags may also deploy under the situation shown in the illustration.
●The angle of vehicle tip-up is marginal. ●The vehicle skids and hits a curb stone.
■Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision. But, whenever a collision of any type causes suffi- cient forward deceleration of the vehicle, deployment of the SRS front air- bags may occur.
●Collision from the side ●Collision from the rear ●Vehicle rollover
116
1-7. Safety information
■Types of collisions that may not deploy the SRS airbag
(side airbags and curtain shield airbags) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.
●Collision from the side to the vehicle body other than the passenger com- partment
●Collision from the side at an angle
The SRS side airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low- speed side collision.
●Collision from the front ●Collision from the rear ●Vehicle rollover
The SRS curtain shield airbags are not generally designed to inflate if the vehicle is involved in a rear collision, if it pitches end over end, or if it is involved in a low-speed side collision.
●Collision from the front* ●Collision from the rear ●Pitching end over end *: Depending on the conditions and type of accident, the curtain shield airbags may deploy frontal impact.
(inflate) upon
117
1-7. Safety information
■When to contact your Toyota dealer
In the following cases, contact your Toyota dealer as soon as possible. ●Any of the SRS airbags have been inflated.
●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.
●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.
●The pad section of the steering wheel, dashboard near the front passenger air- bag or lower portion of the instrument panel is scratched, cracked, or other- wise damaged.
●The surface of the seats with the side airbag is scratched, cracked or other- wise damaged.
●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or other- wise damaged.
118
1
1-7. Safety information
CAUTION
■SRS airbag precautions
Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts
properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you now sit less than 10
in. (250 mm) away, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching thepedals comfortably.
• Slightly recline the back of the seat.
Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-
bag toward your chest instead of your head and neck.
The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals and steering wheel, and your view of the instrument panel controls.
119
1-7. Safety information
CAUTION
■SRS airbag precautions
●If the seat belt extender has been con- nected to the front seat belt buckles but the seat belt extender has not also been fastened to the latch plate of the seat belt, the SRS front airbags will judge that the driver and front passen- ger are wearing the seat belt even though the seat belt has not been con- nected. In this case, the SRS front air- bags may not activate correctly in a collision, resulting in death or serious injury in the event of a collision. Be sure to wear the seat belt with the seat belt extender.
●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.
●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children. (P. 129)
120
1-7. Safety information
CAUTION
■SRS airbag precautions
●Do not sit on the edge of the seat or
lean against the dashboard.
●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
●Do not drive the vehicle while the driver or passenger has items resting on their knees.
●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.
●Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.
121
1-7. Safety information
CAUTION
■SRS airbag precautions
●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.
●Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip.
●Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and seriously injure or kill you, should the SRS curtain shield airbag deploy.
●Do not attach any heavy, sharp or hard objects such as keys or accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver’s seat area by the force of the deploying airbag, thus causing a danger.
●If the vinyl cover is put on the area where the SRS knee airbags will
deploy, be sure to remove it.
●Do not use seat accessories which cover the parts where the SRS side
airbags inflate as they may interfere with inflation of the SRS airbags.
●Do not strike or apply significant levels of force to the area of the SRS air-
bag components (P. 113). Doing so can cause the SRS airbags to malfunction.
●Do not touch any of the component parts immediately after the SRS air-
bags have deployed (inflated) as they may be hot.
122
1-7. Safety information
CAUTION
■SRS airbag precautions
●If breathing becomes difficult after the SRS airbag has deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.
●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.
■Modification and disposal of SRS airbag system components
Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags. ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails.
●Repairs or modifications of the front fender, front bumper, or side of the
occupant compartment.
●Installation of a grille guard (bull bars, kangaroo bar, etc.), snow plows,
winches or roof luggage carrier.
●Modifications to the vehicle’s suspension system. ●Installation of electronic devices such as mobile two-way radios or CD
players.
●Modifications to your vehicle for a person with a physical disability.
123
1-7. Safety information Front passenger occupant classification system
Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
SRS warning light Front passenger’s seat belt reminder light AIR BAG ON indicator light AIR BAG OFF indicator light
124
1
1-7. Safety information
Conditions and operation of the front passenger occupant classification system ■ Adult*1
Indicator/
warning light
AIR BAG ON and AIR BAG OFF indica-
tor lights
SRS warning light
Front passenger’s seat belt reminder
light
AIR BAG ON
Off
Flashing*2
Devices
Front passenger airbag
Front passenger knee airbag
Side airbag on the front passenger seat Curtain shield airbag in the front passen-
ger side
Front passenger’s seat belt pretensioner
■ Child*3 or child restraint system*4
Activated
Indicator/
warning light
Devices
AIR BAG ON and AIR BAG OFF indica-
tor lights
SRS warning light
