Download PDF Manual

■Automatic locking retractor (ALR)


When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (→P. 121)


■Pregnant women


Obtain medical advice and wear the seat belt in the proper way. (→P. 68) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.


■People suffering illness


Obtain medical advice and wear the seat belt in the proper way.


71


1-3. Adjustable components (seats, mirrors, steering wheel)


■When not using the rear seat belts


Second seats


Pass the outer seat belts through the seat belt hangers and secure the seat belt plates to prevent the shoulder belts from being damaged.


Third seats


Pass the seat belts through the seat belt hangers to prevent the shoulder belts from being damaged.


■Child seat belt usage


The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle's seat belt. (→P. 117) ●When the child becomes large enough to properly wear the vehicle's seat


belt, follow the instructions on P. 68 regarding seat belt usage. ■Replacing the belt after the pretensioner has been activated


If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.


72


1-3. Adjustable components (seats, mirrors, steering wheel)


■Seat belt extender


If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.


they are not


CAUTION


Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or severe injury. ■Wearing a seat belt


●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt


for more than one person at once, including children.


●Toyota recommends that children be seated in the rear seat and always


use a seat belt and/or an appropriate child restraint system.


●Do not recline the seat any more than necessary to achieve a proper seat- ing position. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.


●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.


■Adjustable shoulder anchor


Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (→P. 69)


73


1-3. Adjustable components (seats, mirrors, steering wheel)


CAUTION


■Seat belt pretensioners


●Do not place anything, such as a cushion, on the front passenger's seat. Doing so will disperse the passenger's weight, which prevents the sensor from detecting the passenger's weight properly. As a result, the seat belt pretensioner for the front passenger's seat may not activate in the event of a collision.


●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.


■Child restraint lock function belt precaution


Do not allow children to play with the child restraint lock function belt. If the belt becomes twisted around a child’s neck, it will not be possible to pull the belt out leading to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.


■Seat belt damage and wear


●Do not damage the seat belts by allowing the belt, plate, or buckle to be


jammed in the door.


●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belt cannot protect an occupant from death or serious injury.


●Ensure that the belt and tab are locked and the belt is not twisted.


If the seat belt does not function correctly, immediately contact your Toyota dealer.


●Replace the seat assembly, including the belts, if your vehicle has been


involved in a serious accident, even if there is no obvious damage.


●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly resulting in death or serious injury.


74


1-3. Adjustable components (seats, mirrors, steering wheel)


CAUTION


■When using the second center seat belt


Do not use the second center seat belt with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking or a collision.


■Using a seat belt extender


●Do not wear the seat belt extender if you can fasten the seat belt without


the extender.


●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.


●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.


NOTICE


■When using a seat belt extender


When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.


75


1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel


The steering wheel can be adjusted to a comfortable position.


STEP 1


STEP 2


Hold the steering wheel and press the lever down.


Adjust to the ideal position by moving the steering wheel horizontally and vertically.


After adjustment, pull the lever up the steering wheel.


to secure


CAUTION


■Caution while driving


Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.


■After adjusting the steering wheel


Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident and resulting in death or serious injury.


76


1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror


Glare from the headlights of vehicles behind can be reduced by using the following functions.


Manual anti-glare inside rear view mirror


Normal position Anti-glare position


Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.


Turns automatic mode on/off


The indicator comes on when automatic mode is turned ON. Vehicles without smart key system: The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position. Vehicles with smart key sys- tem: The mirror will revert to the automatic mode each time the “ENGINE STOP” switch is turned to IGNITION ON mode.


START


77


1-3. Adjustable components (seats, mirrors, steering wheel)


Adjusting the height of rear view mirror


Adjust the height of the rear view mirror by moving it up and down.


■To prevent sensor error (vehicles with auto anti-glare inside rear view


mirror)


To ensure that the sensors operate prop- erly, do not touch or cover them.


CAUTION


■Caution while driving


Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.


78


1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors


Vehicles without smart key system


Mirror angle can be adjusted using the switch when the engine switch is in the “ACC” or “ON” position.


Vehicles with smart key system


Mirror angle can be adjusted using the switch when the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.


STEP 1


Select a mirror to adjust.


Left Right


STEP 2


Adjust the mirror.


Up Right Down Left


79


1-3. Adjustable components (seats, mirrors, steering wheel)


Folding back the mirrors


Push backward to fold the mir- rors.


■When the mirrors are fogged up (vehicles with outside rear view mirror


defoggers) Turn on the mirror defoggers to defog the mirrors. (→P. 233)


CAUTION


■When driving the vehicle


Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded back. ●Both the driver and passenger side mirrors must be extended and properly


adjusted before driving.


■When the mirror defoggers are operating (vehicles with outside rear


view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.


80


1


1-4. Opening and closing the windows and moon roof Power windows


The power windows can be opened and closed using the following switches.


Closing One-touch closing (driver’s window only)* Opening One-touch opening (driver’s window only)*


*: Pressing


the switch


the opposite direction will stop win- dow travel partway.


in


Lock switch


Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.


81


1-4. Opening and closing the windows and moon roof


■The power windows can be operated when


Vehicles without smart key system


The engine switch is in the “ON” position.


Vehicles with smart key system


The “ENGINE START STOP” switch is in IGNITION ON mode.


■Operating the power windows after turning the engine off (front win-


dows only)


Vehicles without smart key system


The power windows can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, how- ever, be operated once either front door is opened.


Vehicles with smart key system


The power windows can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. They cannot, however, be operated once either front door is opened.


■Jam protection function (driver’s window only)


If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.


■When the battery is disconnected


The power windows must be initialized in order to ensure proper operation. (Initialize each window with the respective switches.)


STEP 1


STEP 2


Open the window fully. Fully close the window by pulling the switch up and holding it for 1 second.


82


1


1-4. Opening and closing the windows and moon roof


CAUTION


■Closing the windows


Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body


in a position where it could be caught when a window is being operated.


●Do not allow children to operate the power windows.


Closing a power window on someone can cause serious injury, and in some instances, even death.


■Jam protection function (driver’s window only)


●Never try jamming any part of your body to activate the jam protection


function intentionally.


●The jam protection function may not work if something gets caught just


before the window fully closes.


83


1-4. Opening and closing the windows and moon roof Moon roof∗


Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing


Open The moon roof stops slightly before the fully opened posi- tion. Press the switch again to fully open. Close Press either side of the switch to stop the moon roof partway.


Tilt up Tilt down Press either side of the switch to stop the moon roof partway.


■ Tilting up and down


■The moon roof can be operated when


Vehicles without smart key system


The engine switch is in the “ON” position.


Vehicles with smart key system


The “ENGINE START STOP” switch is in IGNITION ON mode.


84


∗: If equipped


1-4. Opening and closing the windows and moon roof


■Operating the moon roof after turning the engine off


Vehicles without smart key system


The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, how- ever, be operated once either front door is opened.


Vehicles with smart key system


The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. They cannot, however, be operated once either front door is opened.


■Jam protection function


If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.


■If the moon roof cannot be closed


If the moon roof cannot be closed automatically, such as when the jam pro- tection function activates accidentally due to a malfunction, press and hold the “TILT UP” side of the switch until the moon roof slide closed completely.


■To reduce wind noise


Drive with the moon roof opened to a position that is slightly before the fully open position as driving with the moon roof opened fully will cause wind noise.


■Sunshade


The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.


■Opening the moon roof by small degrees


Quickly press and release the switch. ■When the battery is disconnected


The moon roof must be initialized in order to ensure proper operation. Press and hold the “TILT UP” side of the switch until the moon roof tilts up completely.


85


1-4. Opening and closing the windows and moon roof


■When the moon roof does not close normally


Perform the following procedure: ●If the moon roof closes but then re-opens slightly


STEP 1


STEP 2


STEP 3


Stop the vehicle. Press and hold the “TILT UP” switch.*1 The moon roof will close, reopen and pause for approximately 10 seconds.*2 Then it will close again, tilt up and pause for approxi- mately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.


●If the moon roof tilts down but then tilts back up


STEP 1


STEP 2


STEP 3


STEP 4


Stop the vehicle. Press and hold the “TILT UP” switch*1 until the moon roof moves into the tilt up position and stops. Release the “TILT UP” switch once and then press and hold the “TILT UP” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up position.*2 Then it will adjust slightly and pause for approximately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch. *1:If the switch is released at the incorrect time, the procedure will


have to be performed again from the beginning.


*2:If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “TILT UP” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.


If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.


86


1


1-4. Opening and closing the windows and moon roof


CAUTION


■Opening the moon roof


Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-


cle while it is moving.


●Do not sit on top of the moon roof.


■Closing the moon roof


Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where it could be caught when the moon roof is being operated.


●Do not allow children to operate the moon roof.


Closing the moon roof on someone can cause death or serious injury.


■Jam protection function


●Never try jamming any part of your body to activate the jam protection


function intentionally.


●The jam protection function may not work if something gets caught just


before the moon roof fully closes.


87


1-5. Refueling Opening the fuel tank cap


Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle


Vehicles without smart key system


Turn the engine switch to the “LOCK” position and ensure that all the doors and windows are closed.


Vehicles with smart key system


Turn the “ENGINE START STOP” switch OFF and ensure that all the doors and windows are closed.


■ Opening the fuel tank cap


STEP 1


Pull up the fuel filler door opener.


STEP 2


Turn the fuel tank cap slowly to open.


88


1-5. Refueling


STEP 3


Hang the fuel tank cap on the back of the fuel filler door.


Closing the fuel tank cap


When replacing the fuel tank cap, turn it until a clicking sound is heard.


After releasing your hand, the cap will turn slightly to the opposite direction.


■Fuel types


Use unleaded gasoline. (Octane rating 87 [Research Octane Number 91] or higher)


■Fuel tank capacity


Approximately 15.9 gal. (60 L, 13.2 Imp. gal.)


89


1-5. Refueling


CAUTION


■Refueling the vehicle


Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●Touch the vehicle or some other metal surface to discharge any static


electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.


●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury.


●Do not allow anyone that has not discharged static electricity from their


bodies to come close to an open fuel tank.


●Do not inhale vaporized fuel.


Fuel contains substances that are harmful if inhaled.


●Do not smoke while refueling the vehicle.


Doing so may cause the fuel to ignite and cause a fire.


●Do not return to the vehicle or touch any person or object that is statically


charged. This may cause static electricity to build up, resulting in a possible ignition hazard.


■When replacing the fuel cap


Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.


90


1-5. Refueling


NOTICE


■Refueling


Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.


91


1-6. Theft deterrent system Engine immobilizer system


The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.


from


indicator


Vehicles without smart key system: The light flashes after the key has been removed the engine switch to indicate that the sys- tem is operating. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed. Vehicles with smart key sys- tem: The indicator light flashes after the “ENGINE START STOP” switch has been turned OFF to indicate that the sys- tem is operating. The indicator light stops flash- ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled.


92


1


1-6. Theft deterrent system


■System maintenance


The vehicle has a maintenance-free type engine immobilizer system.


■Conditions that may cause the system to malfunction


●If the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system


(key with a built-in transponder chip) of another vehicle


■Certifications for the engine immobilizer system


●For vehicles sold in the U.S.A.


Vehicles without smart key system


FCC ID: MOZRI-20BTY FCC ID: MOZRI-21BTY


Vehicles with smart key system


FCC ID: NI4TMIMB-1
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ●For vehicles sold in Canada This device complied with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.


93


1-6. Theft deterrent system


NOTICE


■To ensure the system operates correctly


Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.


94


1-6. Theft deterrent system Theft prevention labels (U.S.A.)


These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.


95


1-7. Safety information Correct driving posture


Drive in a good posture as follows:


and to


Sit upright and well back in the seat. (→P. 49) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (→P. 49) Adjust the seatback so that the controls are easily oper- able. Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (→P. 76) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 65) Wear the seat belt correctly. (→P. 68)


96


1-7. Safety information


CAUTION


■While driving


●Do not adjust the position of the driver's seat while driving.


Doing so could cause the driver to lose control of the vehicle.


●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.


●Do not place anything under the front seats.


Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent. The adjustment mechanism may also be damaged.


■Adjusting the seat position


●Take care when adjusting the seat position to ensure that other passen-


gers are not injured by the moving seat.


●Do not put your hands under the seat or near the moving parts to avoid


injury. Fingers or hands may become jammed in the seat mechanism.


97


1-7. Safety information SRS airbags


The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.


Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components.


Side and curtain shield airbags (if equipped) Side airbags Can help protect the torso of the front seat occupants. Curtain shield airbags Can help protect primarily the head of occupants in the outer seats.


98


Airbag system components


1-7. Safety information


Curtain shield airbags (if equipped) Side airbags (if equipped) Front passenger airbag Side and curtain shield air- bag sensors (if equipped) Front airbag sensors Front passenger’s seat belt buckle switch Curtain shield airbag sen- sors (if equipped)


“AIR BAG ON” and “AIR BAG OFF” indicator lights SRS warning light Driver airbag Driver’s seat position sen- sor Driver’s seat belt buckle switch Airbag sensor assembly Front passenger occupant classification system (ECU and sensors)


Your vehicle is equipped with ADVANCED AIRBAGS designed based on US motor vehicle safety standards (FMVSS208). The airbag sys- tem controls airbag deployment power for the driver and front pas- senger. The driver airbag system consists of the driver seat's position sensor etc. The front passenger's airbag system consists of the front passenger occupant classification sensor etc.


99


1-7. Safety information


The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants.


■SRS warning light


This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensors (if equipped), curtain shield airbag sensors (if equipped), driver's seat position sensor, driver's seat belt buckle switch, front passenger occupant classification system, “AIR BAG ON” and “AIR BAG OFF” indicator lights, front passenger’s seat belt buckle switch, seat belt pretensioner assemblies, inflators, interconnecting wiring and power sources. (→P. 419)


■If the SRS airbags deploy (inflate)


●Bruising and slight abrasions may result from contact with a deploying


(inflating) SRS airbag.


●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, and parts of the front and rear pillars and roof side rail, may be hot for several minutes. The airbag itself may also be hot.


●The windshield may crack.


100


1


1-7. Safety information


■SRS airbag deployment conditions


Front airbags


●The front SRS airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to a 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck, etc.).


●It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together.


●The SRS front passenger airbag will not activate if there is no passenger sitting in the front passenger seat. However, the front passenger airbag may deploy if luggage is put in the seat, or the seat belt is fastened, even if the seat is unoccupied. (→P. 111) Side airbags and curtain shield airbags (if equipped)


●The SRS side airbags and SRS curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by a 3300 lb. [1500 kg] vehi- cle colliding with the vehicle cabin from a direction perpendicular to the vehicle orientation at a speed of 12 - 18 mph [20 - 30 km/h]) or vehicle rollover.


●The SRS side airbag on the passenger seat will not activate if there is no passenger sitting in the front passenger seat. However, the side airbag on the passenger seat may deploy if luggage is put in the seat, or the seat belt is fastened, even if the seat is unoccupied. (→P. 111)


●The SRS curtain shield airbags are designed to inflate when the passen- ger compartment is subjected to a severe impact from the side or vehicle rollover.


101


1-7. Safety information


■Conditions under which the SRS airbags may deploy (inflate), other


than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


●Hitting a curb, edge of pavement or


hard surface


●Falling into or jumping over a deep hole ●Landing hard or vehicle falling


The SRS curtain shield airbags (if equipped) may also deploy under the situ- ation shown in the illustration.


●The angle of vehicle tip-up is marginal. ●The vehicle skids and hits a curb stone.


■Types of collisions that may not deploy the SRS front airbags


The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision. But, whenever a collision of any type causes suffi- cient forward deceleration of the vehicle, deployment of the SRS front air- bags may occur.


●Collision from the side ●Collision from the rear ●Vehicle rollover


102


1-7. Safety information


■Types of collisions that may not deploy the SRS side airbags and cur-


tain shield airbags (if equipped) The SRS side airbag and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a colli- sion to the side of the vehicle body other than the passenger compartment.


●Collision from the side to the vehicle body other than the passenger com- partment


●Collision from the side at an angle


The SRS side airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low- speed side collision.


●Collision from the front ●Collision from the rear ●Vehicle rollover


The SRS curtain shield airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it pitches end over end, or if it is involved in a low-speed side collision.


●Collision from the front ●Collision from the rear ●Pitching end over end


103


1-7. Safety information


■When to contact your Toyota dealer


In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer. ●Any of the SRS airbags have been inflated.


●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.


●Vehicles with side airbags and curtain shield airbags: A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.


●The pad section of the steering wheel or dashboard is scratched, cracked, or otherwise damaged.


●Vehicles with side airbags: The surface of the seats with the side airbag is scratched, cracked or otherwise dam- aged.


●Vehicles with curtain shield airbags: The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or other- wise damaged.


104


1


1-7. Safety information


CAUTION


■SRS airbag precautions


Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts


properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching the


pedals comfortably.


• Slightly recline the back of the seat.


Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-


bag toward your chest instead of your head and neck. The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.


105


1-7. Safety information


CAUTION


■SRS airbag precautions


●If the seat belt extender has been con- nected to the driver's seat belt buckle but the seat belt extender has not also been fastened to the latch plate of the driver's seat belt, the SRS driver's air- bag system will judge that the driver is wearing the seat belt even though the seat belt has not been connected. In this case, the driver's airbag may not activate correctly in a collision, resulting in death or serious injury in the event of collision. Be sure to wear the seat belt with the seat belt extender.


●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.


●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children. (→P. 117)


106


1-7. Safety information


CAUTION


■SRS airbag precautions


●Do not sit on the edge of the seat or


lean against the dashboard.


●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.


●Do not drive the vehicle while the driver or passenger has items resting on their knees.


●Vehicles with side airbags and curtain shield airbags: Do not lean against the door, the roof side rail or the front, side and rear pillars.


●Vehicles with side airbags and curtain shield airbags: Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.


107


1-7. Safety information


CAUTION


■SRS airbag precautions


●Do not attach anything to or lean any- thing against areas such as the dash- board or steering wheel pad. These items can become projectiles when SRS driver and front passenger airbags deploy.


●Vehicles with side airbags and curtain shield airbags: Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars or roof side rail garnish.


●Vehicles with curtain shield airbags: Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and seriously injure or kill you, should the SRS curtain shield airbag deploy.


●Vehicles with side airbags: Do not use seat accessories which cover the parts where the SRS side airbags inflate as they may interfere with infla- tion of the airbags.


●Do not strike or apply significant levels of force to the area of the SRS air-


bag components (→P. 99). Doing so can cause the SRS airbags to malfunction.


108


1-7. Safety information


CAUTION


■SRS airbag precautions


●Do not touch any of the component parts immediately after the SRS air-


bags have deployed (inflated) as they may be hot.


●If breathing becomes difficult after the SRS airbag has deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.


●Vehicles without side and curtain shield airbags: If the areas where the SRS airbags are stored, such as the steering wheel pad are damaged or cracked, have them replaced by your Toyota dealer.


●Vehicles with side and curtain shield airbags: If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.


109


1-7. Safety information


CAUTION


■Modification and disposal of SRS airbag system components


Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags. ●Vehicles without side airbags and curtain shield airbags: Repairs, modifi- cations, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery.


●Vehicles with side airbags and curtain shield airbags: Repairs, modifica- tions, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rail.


●Repairs or modifications of the front fender, front bumper, or side of the


occupant compartment.


●Installation of snow plows, winches, etc. to the front grille (bull bars, kan-


garoo bar etc.).


●Modifications to the vehicle's suspension system. ●Installation of electronic devices such as mobile two-way radios or CD


players.


●Modifications to your vehicle for a person with a physical disability.


110


1-7. Safety information Front passenger occupant classification system


Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger.


SRS warning light Front passenger's seat belt reminder light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light


111


1-7. Safety information


Conditions and operation of the front passenger occupant classification system ■ Adult*1


Indicator/


warning light


Devices


“AIR BAG ON” and “AIR BAG OFF” indi-


cator lights


SRS warning light


Front passenger's seat belt reminder


light


Front passenger airbag


Side airbag on the front passenger seat Curtain shield airbag in the front passen-


ger side


Front passenger's seat belt pretensioner


“AIR BAG


ON” Off


Flashing*2


Activated


■ Child*3 or child restraint system*4


Indicator/


warning light


Devices


“AIR BAG ON” and “AIR BAG OFF” indi-


cator lights


SRS warning light


Front passenger's seat belt reminder


light


Front passenger airbag


Side airbag on the front passenger seat Curtain shield airbag in the front passen-


ger side


Front passenger's seat belt pretensioner


“AIR BAG OFF”*5


Off


Flashing*2


Deactivated


Activated


112


1


1-7. Safety information


■ Unoccupied


Indicator/


warning light


Devices


“AIR BAG ON” and “AIR BAG OFF” indi-


cator lights


SRS warning light


Front passenger's seat belt reminder


light


Front passenger airbag


Side airbag on the front passenger seat Curtain shield airbag in the front passen-


ger side


Not illumi-


nated


Off


Deactivated


Activated


Front passenger's seat belt pretensioner Deactivated


■ There is a malfunction in the system


Indicator/


warning light


Devices


“AIR BAG ON” and “AIR BAG OFF” indi-


cator lights


SRS warning light


Front passenger's seat belt reminder


light


Front passenger airbag


Side airbag on the front passenger seat Curtain shield airbag in the front passen-


ger side


Front passenger's seat belt pretensioner


“AIR BAG


OFF” On


Off


Deactivated


Activated


*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.


*2: In the event the front passenger does not wear a seat belt. *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.


113


1-7. Safety information


*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 118)


*5: In case the indicator is not illuminated, consult this manual as for


installing the child restraint system properly. (→P. 121)


114


1


1-7. Safety information


CAUTION


■Front passenger occupant classification system precautions


Observe the following precautions regarding front passenger occupant clas- sification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger's seat belt tab has not been left inserted


into the buckle before someone sits in the front passenger seat.


●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, then reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the front passenger airbag, side airbag on the front passenger side may not activate correctly, which could cause death or serious injury in the event of collision.


●Do not apply a heavy load to the front passenger seat or equipment (e.g.


seatback pocket).


●Do not put weight on the front passenger seat by putting your hands or


feet on the front passenger seat seatback from the second seat.


●Do not let a passenger in the second seat lift the front passenger seat with


their feet or press on the seatback with their legs. ●Do not put objects under the front passenger seat. ●Do not recline the front passenger seatback so far that it touches a second seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger's airbags will not deploy in the event of a severe accident. If the seatback touches the second seat, return the seatback to a position where it does not touch the second seat. Keep the front passenger seatback as upright as possible when the vehicle is mov- ing. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.


115


1-7. Safety information


CAUTION


■Front passenger occupant classification system precautions


●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the second seat, or if that is not possible, move the front passenger seat fully rearward.


●When it is unavoidable to install the forward-facing child restraint system on the front passenger seat, install the child restraint system on the front passenger seat in the proper order. (→P. 121)


●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.


●Child restraint systems installed on the second seat should not contact the


front seatbacks.


●Do not use a seat accessory, such as a cushion or seat cover, that covers


the seat cushion surface.


●Do not modify or replace the upholstery of the front seat.


116


1-7. Safety information Child restraint systems


A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.


Points to remember


Studies have shown that installing a child restraint on a rear seat is much safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and is


appropriate to the age and size of the child.


● For installation details, follow the instructions provided with the


child restraint system. General installation instructions are provided in this manual. (→P. 121)


117


1-7. Safety information


Types of child restraint


Child restraint systems are classified into the following 3 types according to the age and size of the child.


Rear facing ⎯ Infant seat/convertible seat


Forward facing ⎯ Convertible seat


Booster seat


118


1-7. Safety information


■Selecting an appropriate child restraint system


●Use a child restraint system appropriate for the child until the child


becomes large enough to properly wear the vehicle’s seat belt.


●If a child is too large for a child restraint system, sit the child on a rear


seat and use the vehicle's seat belt. (→P. 68)


CAUTION


■Child restraint precautions


●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.


●Never install a rear-facing child restraint system on the front passenger


seat even if “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag can cause death or serious injury to the child if the rear-fac- ing child restraint system is installed on the front passenger seat.


●A forward-facing child restraint system may be installed on the front pas- senger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illumi- nated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.


119


1-7. Safety information


CAUTION


■Child restraint precautions


●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or accident.


●Vehicles with side airbags and curtain shield airbags: Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.


●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or an accident.


■Child restraint lock function belt precaution


Do not allow children to play with the child restraint lock function belt. If the belt becomes twisted around a child’s neck, it will not be possible to pull the belt out leading to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.


■When the child restraint system is not in use


●Keep the child restraint system properly secured on the seat even if it is


not in use. Do not store the restraint unsecured in the passenger compartment.


●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the luggage compartment. This will prevent it from injuring passengers in the event of a sudden stop, sudden swerve or accident.


120


1-7. Safety information Installing child restraints


Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the outside rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.


Second outside seats: Child restraint LATCH anchors


LATCH anchors are provided for the rear outside seats. (But- tons displaying the location of the anchors are attached to the seats.)


Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt)


121


Second outside seats: Anchor brackets (for top tether strap)


Anchor brackets are provided for the second outside seats.


Second center seat: Anchor brackets (for top tether strap)


An anchor bracket is provided for the second center seat.


1-7. Safety information


122


1-7. Safety information


Installation with LATCH system (second outside seats only)


STEP 1


Type A


STEP 2


Canada only


Fold the seatback while pulling the lever. Return the seatback and secure it at the 1st lock posi- tion (most upright position). Adjust the seatback to the 3rd lock position. (→P. 54)


1st lock position 7th lock position


Latch the hooks of the lower straps onto the LATCH anchors. The bars are installed in the clearance between the seat cush- ion and seatback. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.


For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.


123


the buckles onto


Latch LATCH anchors.


the


The bars are installed in the clearance between the seat cush- ion and seatback. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.


For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.


1-7. Safety information


Type B


STEP 2


Canada only


124


1-7. Safety information


Installing child restraints using a seat belt (child restraint lock function belt)


■ Rear facing ⎯ Infant seat/convertible seat


STEP 1


STEP 2


STEP 3


Loading...
x