2010 Toyota Highlander Owners Manual

FEATURES/OPERATIONS

Tilt and telescopic steering wheel

Angle

Length

Lock release lever

Hold wheel, push lever down, set angle and length, and return lever. NOTE: Do not attempt to adjust while the vehicle is in motion.

Moonroof (if equipped) Sliding operation

Push once to open partway; again to open completely.

Open

Close

Tilting operation

Tilt

Close

Recommended driving position to minimize wind noise.

Door-Power back (if equipped) Instrument panel

Back door (close only)

Push and hold

Open: Push and hold Close: Push and hold again

Push

NOTE: If battery is disconnected, the power back door needs to be reinitialized. Refer to the Owner’s Manual for more details.

12

Seat adjustments-Front Manual seat

Power seat

Seat position (forward/backward) Seat cushion angle Height crank (driver side only) Seatback angle Seat position, cushion angle and height Driver seat leg support (if equipped) Lumbar support (driver side only)

Seat adjustments-Rear Second row seat Without third seat

With third seat

Seat position (forward/backward) Seatback angle Third seat access lever Seatback release

Refer to the Owner’s Manual for more details.

13

FEATURES/OPERATIONS

Seats-Head restraints Front

Rear

Height

Angle (if equipped)

Lock release button

Lock release button

Seats-Removing Center-StowTM second row seat (1)

(2)

(3)

(4)

(5)

(1) Remove the second row console from the front center console box. (2) Lower the center head restraint. (3) Pull the strap, then fold down the seatback. (4) Pull the lever behind the second center seat and lift the rear of the

seat to remove.

(5) Stow the seat in the front center console box.

NOTE: The second-row console can now be installed between the second row seats. Seats-Stowing third row seats (if equipped)

Pull

Fold down

Refer to the Owner’s Manual for more details.

14

Pull

Seats-Folding down second row seats (if equipped) From outside

From inside

Left side/center remote seat release

Right side remote seat release

(1) Pull up

(2) Fold down

Windshield wipers & washers Front

Adjust frequency*

Single wipe

* Intermittent windshield

wiper frequency adjustment Rotate to increase/decrease wipe frequency.

Rear

Pull to wash and wipe

Interval wipe

Slow

Fast

Wash and wipe Wipe Interval wipe

Wash and wipe

15

FEATURES/OPERATIONS

Lights & turn signals Headlights

With DRL OFF switch

Without DRL OFF switch

Headlights Parking lights

Auto DRL OFF

Auto Headlights Parking lights

Low beam

High beam flasher

High beam

-Daytime Running Light system (DRL) (if equipped) Automatically turns on the turn signal lights at a reduced intensity. -Automatic light cut off system Automatically turns lights off after a delay of 30 seconds. Front fog lights (if equipped)

Turn

Front fog lights come on only when the headlights are on low beam.

Turn signals

Right turn

Lane change

Lane change

Left turn

16

Power outlets-12V DC

Instrument panel (with seat heater)

Instrument panel (without seat heater)

Center console

Luggage compartment

Key/Engine switch must be in the “ACC” or “ON” position to be used.

Power outlets-115V AC (if equipped)

ON/OFF switch

Beside second row seat

Key/Engine switch must be in the “ON” position to be used.

17

FEATURES/OPERATIONS

Multi-information display (if equipped)

Push “DISP” to change information in the following: (1) Average gas mileage after refueling (2) Current gas mileage (3) Miles left on remaining fuel (4) Driving distance from engine start (5) Average gas mileage (6) Average gas mileage history

Push and hold “DISP” to set up the displays and the rearview monitor displays.

Windows-Power Driver side

Up

Down

Window lock switch

Automatic operation (driver’s window only) Push the switch completely down or pull it completely up and release to fully open or close. To stop window midway, lightly push the switch in the opposite direction. Window lock switch Deactivates all passenger windows. Driver’s window remains operable.

18

Telephone controls (Bluetooth®) (if equipped) Audio unit

Microphone

Steering wheel telephone controls

Volume

End call

Start call

Voice command button

Bluetooth® technology allows dialing or receipt of calls without taking hands from the steering wheel or using a cable to connect the telephone and the system. Refer to “Hands-free phone system (for cellular phone),” Section 3-4 in the Owner’s Manual for more details, or go to Toyota.com and enter “Bluetooth” in the keyword search.

19

FEATURES/OPERATIONS

Air Conditioning/Heating Front manual Air Conditioning

Fan speed Outside rearview mirror (if equipped)/Rear window defogger Temperature selector Fresh or recirculated cabin air Airflow vent In “ ” or “ reduce window fogging. Air Conditioning ON/OFF Use fresh air to quickly cool interior, then change to recirculate for cooler air. Use for quick cooling. Air intake will automatically be set to recirculate. Rear Air Conditioning ON/OFF

” mode, use fresh air (“

” indicator OFF) to

Rear manual Air Conditioning (if equipped)

Airflow vent Temperature selector Fan speed

20

Front automatic Air Conditioning With rear Air Conditioning

Without rear Air Conditioning

Automatic climate control ON Adjusting the temperature setting will cause the airflow vents, air intake and fan to adjust automatically. Windshield airflow/defogger Rear Air Conditioning ON/OFF Fan speed Outside rearview mirror (if equipped)/Rear window defogger Fresh or recirculated cabin air Temperature selector (front passenger side) Air Conditioning ON/OFF “DUAL” button Indicator ON: Separate temperature settings for driver, front passenger and rear passengers. Indicator OFF: Synchronize temperature settings for driver and all passengers. Temperature selector (rear passenger) Airflow vent In “ ” or “ reduce window fogging. Climate control OFF Temperature selector (driver side)

” mode, use fresh air (“

” indicator OFF) to

21

FEATURES/OPERATIONS

Rear automatic Air Conditioning (if equipped)

Fan speed Temperature selector Airflow vent Automatic climate control ON Climate control OFF

Seat heaters (if equipped)

Driver’s seat

Turn

Push

Push

Front passenger’s seat

Push knob to pop the controller out. Turn clockwise for heater.

Clock Without multi-information display

H-Hour set M-Minute set

With multi-information display

With multi-information display Press and hold “DISP” button. Select “CLOCK” on menu screen. Adjust as indicated on screen.

22

Cruise control Turning system ON/OFF

System ON/OFF

Resume2

Increase speed

Functions

Cancel1

Set

Decrease speed

1 The set speed may also be cancelled by depressing the brake pedal. 2 The set speed may be resumed once vehicle speed exceeds 25 mph.

Garage door opener (HomeLink®)* (if equipped)

Garage door openers manufactured under license from HomeLink®* can be programmed to operate garage doors, estate gates, security lighting, etc.

Refer to “Garage door opener,” Section 3-7 in the Owner’s Manual for more details. For programming assistance, contact HomeLink® at 1-800-355-3515, or visit http://www.homelink.com. * HomeLink® is a registered trademark of Johnson Controls, Inc.

23

FEATURES/OPERATIONS

Audio

Type 1

Eject CD Station/CD track scan

Preset buttons - functions in other modes indicated above number

Mute View CD text

Push to turn ON/OFF

Seek station/ CD track select

Mode

Push to skip up/down folder and radio category type

Push to adjust tone & balance

Type 2 additional functions

Load CD(s)

Type 3 (with JBL speakers and Bluetooth® function)

AM/Satellite Radio

CD PLAYER To scan tracks on a disc Push and hold “SCAN.” Push again to hold selection. CD changer (Types 2 and 3 only) -To load one disc Push “LOAD” and insert one disc. -To load multiple discs Push and hold “LOAD” until you hear a beep. Insert one disc. Shutter will close and then re-open for next disc. To select a file (MP3/WMA only) Turn “TUNE.FILE.” To select a folder (MP3/WMA only) Push either side of “FOLDER.”

24

RADIO To preset stations Tune in the desired station and hold down a preset button (1-6) until you hear a beep. Push desired preset button (1-6) to select. To scan stations Push and hold “SCAN” to scan preset stations. Push again to hold selection. AUX audio jack Without seat heater

With seat heater

By inserting a mini plug into the AUX audio jack, you can listen to music from a portable audio device through the vehicle’s speaker system while in AUX mode.

Steering wheel controls (if equipped) Audio control A/C control

Volume control

A/C OFF

Temperature selector

Auto A/C ON

”

v v “ Use to search within the selected audio medium (radio, CD, iPod, etc.). “MODE” Push to turn audio ON and select an audio mode. Push and hold to turn the audio system OFF.

25

FEATURES/OPERATIONS

Rear seat entertainment system (if equipped)

Remote control DVD player Headphone volume control and headphone jacks DVD screen 115V AC Power outlet ON/OFF switch Front audio system A/V input adapter 115V AC Power outlet Wireless headphones

Downhill Assist Control system (DAC) (if equipped)

Slip indicator blinking, DAC indicator solid = DAC engaged

DAC indicator blinking = DAC not engaged DAC helps the vehicle to descend steep hills while maintaining a low speed without brake pedal operation. Press the “DAC” button (system will engage only when shifter is in S1 or R mode). Pressing the button again will turn system off. Refer to the Owner’s Manual for more details.

26

Hill-start Assist Control (HAC)

Brake pedal

HAC helps prevent rolling backwards on an incline. To engage, push further down on brake pedal while at a complete stop until a beep sounds and slip indicator illuminates. HAC holds for approximately 2 seconds after releasing brake pedal. Refer to the Owner’s Manual for more details.

Cup holders Front

Console box

Rear

Side table

27

SAFETY AND EMERGENCY FEATURES

Seat belts

Take up slack

Too high

Keep as low on hips as possible

If belt is fully extended, then retracted even slightly, it cannot be re-extended beyond that point, unless fully retracted again. This feature is used to help hold child restraint systems securely.

To find more information about seat belts, and how to install a child restraint system, refer to the Owner's Manual.

Tire Pressure Monitoring (warning) System

System reset initialization 1. Push and hold “

SET” button

until the indicator blinks 3 times.

2. Wait a few minutes to allow

initialization to complete.

SET” button until indicator blinks three times. Let the vehicle sit for

After adjusting tire pressures, or after tires have been rotated or replaced, turn the ignition switch to “ON” and press and hold the “ a few minutes to allow initialization to complete. Refer to the load label on the door jamb or the Owner’s Manual for tire inflation specifications. If the tire pressure indicator flashes for more than 60 seconds and then remains on, take the vehicle to your local Toyota dealer. Note: The warning light may come on due to temperature changes or changes in tire pressure from natural air leakage. If the system has not been initialized recently, setting the tire pressures to factory specifications should turn off the light.

28

Abbreviation list Abbreviation/Acronym list

ABBREVIATIONS MEANING

2 Wheel Drive 4 Wheel Drive Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor Child Restraint System Downhill Assist Control Display Electronic Control Unit Event Data Recorder Emergency Locking Retractor Electric Power Steering Gross Axle Weight Rating Gross Vehicle Mass Emission Inspection and Maintenance Lower Anchors and Tethers for Children Light Emitting Diode On Board Diagnostics Supplemental Restraint System Tire Identification Number Temperature Tire Pressure Warning System Traction Control Vehicle Identification Number Vehicle Stability Control

2WD 4WD A/C ABS ACC ALR CRS DAC DISP ECU EDR ELR EPS GAWR GVM I/M

LATCH LED OBD SRS TIN TEMP TPMS TRAC VIN VSC

592

For your information

Main Owner’s Manual

Please note that this manual covers all models and all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice. Depending on specifications, the vehicle shown in the illustrations may differ from your vehicle in terms of equipment.

Noise from under vehicle after turning off the engine

Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.

Accessories, spare parts and modification of your Toyota

A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that these parts are not covered by Toyota warranty and that Toyota is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle. This vehicle should not be modified with non-genuine Toyota products. Modification with non-genuine Toyota products may affect performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

24

Installation of a mobile two-way radio system

As the installation of a mobile two-way radio system in your vehicle may affect electronic systems such as the multi-port fuel injection system/sequen- tial multi-port fuel injection system, cruise control system, anti-lock brake system, SRS airbag system or seat belt pretensioner system, be sure to check with your Toyota dealer for precautionary measures or special instruc- tions regarding installation.

Scrapping of your Toyota

The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and seat belt pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.

Perchlorate Material

Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. Your vehicle has components that may contain perchlorate. These compo- nents may include airbag, seat belt pretensioners, and wireless remote con- trol batteries.

25

CAUTION

■General precautions while driving

Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury. Defensive driving: Always drive defensively. Anticipate mistakes that other drivers or pedestrians might make and be ready to avoid accidents. Driver distraction: Always give your full attention to driving. Anything that dis- tracts the driver, such as adjusting controls, talking on a cellular phone or reading can result in a collision with resulting death or serious injury to you, your occupants or others.

■General precaution regarding children’s safety

Never leave children unattended in the vehicle, and never allow children to have or use the key. Children may be able to start the vehicle or shift the vehicle into neutral. There is also a danger that children may injure themselves by playing with the windows, the moon roof, or other features of the vehicle. In addition, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.

26

Symbols used throughout this manual

Cautions & Notices

CAUTION

This is a warning against anything which may cause death or injury to people if the warning is ignored. You are informed about what you must or must not do in order to reduce the risk of injury to yourself and others.

NOTICE

This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.

Symbols used in illustrations

Safety symbol The symbol of a circle with a slash through it means “Do not”, “Do not do this”, or “Do not let this happen”.

Arrows indicating operations

Indicates the action (pushing, turning, etc.) used to operate switches and other devices. Indicates the outcome of an operation (e.g. a lid opens).

27

28

TABLE OF CONTENTS

1 Before driving

Adjusting and operating features such as door locks, mirrors, and steering column.

2 When driving

Driving, stopping and safe-driving information.

3 Interior features

Air conditioning and audio systems, as well as other interior features for a comfortable driving experience.

4 Maintenance

and care

Cleaning and protecting your vehicle, performing do-it- yourself maintenance, and maintenance information.

5 When trouble

arises

What to do if the vehicle needs to be towed, gets a flat tire, or is involved in an accident.

6 Vehicle

specifications

Detailed vehicle information.

7 For owners

Reporting safety defects for U.S. owners and seat belt instructions for Canadian owners

Index

Alphabetical listing of information contained in this manual.

1-1. Key information Keys

The following keys are provided with the vehicle.

Vehicles without smart key system (type A)

Master keys Valet key Key number plate

Vehicles without smart key system (type B)

Master keys Valet key Key number plate

Vehicles with smart key system

Electronic keys • Operating

system (→P. 33)

the smart key

• Operating

the wireless

remote control function (→P. 54)

Mechanical keys Key number plate

30

1

1-1. Key information

Using the mechanical key (vehicles with smart key system)

Take out the mechanical key.

After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery is depleted, you will need the mechanical key. (→P. 539)

■When required to leave a key to the vehicle with a parking attendant

Lock the glove box as circumstances demand. (→P. 376) Vehicles without smart key system: Carry the master key for your own use and leave the valet key only with the attendant. Vehicles with smart key system: Remove the mechanical key for your own use and provide the attendant with the electronic key only.

■Key number plate

Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 538)

■When riding in an aircraft (vehicles with smart key system)

When bringing an electronic key onto an aircraft, make sure you do not press any buttons on the electronic key while inside the aircraft cabin. If you are carrying an electronic key in your bag etc, ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the elec- tronic key to emit radio waves that could interfere with the operation of the aircraft.

31

1-1. Key information

NOTICE

■To prevent key damage

●Do not subject the keys to strong shocks, expose them to high tempera-

tures by placing them in direct sunlight, or get them wet.

●Do not expose the keys to electromagnetic materials or attach any mate-

rial that blocks electromagnetic waves to the key surface.

●Do not disassemble the key.

32

1-2. Opening, closing and locking the doors Smart key system∗

The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)

Locks and unlocks doors (→P. 34) Starts the engine (→P. 173)

the

∗: If equipped 33

1-2. Opening, closing and locking the doors

Opens the glass hatch (→P. 36) Locks and unlocks doors (→P. 34)

the

Unlocking and locking the doors

Front door handles

Grip the handle to unlock the doors.

Make sure to touch the sensor on the back of the handle. The door cannot be unlocked for 3 seconds after is locked.

the door

34

Back door handle

1-2. Opening, closing and locking the doors

Press the lock button to lock the doors.

Press the button to unlock the door.

the door

The door cannot be unlocked for 3 seconds after is locked. Lock the back door again when you leave the vehicle. The back door will not lock automatically after it has been opened and then closed.

Press the button to lock the door.

35

1-2. Opening, closing and locking the doors

Opening the glass hatch

Press and hold the button to open the glass hatch. The glass hatch will pop up.

the back door

The glass hatch can be unlocked only when is closed. Lock the glass hatch again when you leave the vehicle. The glass hatch will not lock automatically after it has been opened and then closed.

Antenna location and effective range

■ Antenna location

Antennas outside the cabin Antennas inside the cabin Antenna outside the luggage compartment

36

1

1-2. Opening, closing and locking the doors

■ Effective range (areas within which the electronic key is

detected)

When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the outside front door handles. When starting the engine “ENGINE or changing START STOP” switch modes The system can be operated when the electronic key is inside the vehicle. When opening the glass hatch and locking or unlocking the doors This system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of the back door handle.

37

1-2. Opening, closing and locking the doors

■Operation signals

A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

■Conditions affecting operation

The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system and wireless remote control from operating properly. (Ways of coping: →P. 539) ●When the electronic key battery is depleted ●Near a TV tower, electronic power plant, gas station, radio station, large display, airport or other facility that generates strong radio waves or elec- trical noise

●When carrying a portable radio, cellular phone, cordless phone or other

wireless communication devices

●When the electronic key has come into contact with, or is covered by a

metallic object

●When multiple electronic keys are in the vicinity ●When carrying or using the electronic key together with the following

devices that emit radio waves • Another vehicle’s electronic key • A wireless key that emits radio waves • Personal computer

●If window tint with a metallic content or metallic objects are attached to

the rear window

■Switching the door unlock function

It is possible to set which doors the entry function unlocks. STEP 1

Turn the “ENGINE START STOP” switch OFF.

When the indicator on the key surface is turned off, push and hold for approximately 5 seconds while pushing

, or

on the key.

STEP 2

38

1-2. Opening, closing and locking the doors

The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)

Multi-information

display

Unlocking doors

Beep

Hold the driver's door han- dle to unlock only the driver's door. Hold the front passenger’s door handle to unlock all doors. Hold either front door han- dle to unlock all doors.

Exterior: Beeps three times Interior: Pings once

Exterior: Beeps twice Interior: Pings once

STEP 3

Unlock the doors using the wireless remote control and open one of the doors. If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set. In case that the alarm is triggered, immediately stop the alarm. (→P. 122)

■Battery-saving function

In the following circumstances, the entry function is disabled in order to pre- vent the vehicle and electronic key batteries from discharging. ●When the entry function has not been used for 2 weeks or more ●When the electronic key has been left within approximately 3 ft. (1 m) of

the vehicle for 10 minutes or more

The system will resume operation when... ●The vehicle is locked using the door handle lock button. ●The vehicle is locked/unlocked using the wireless remote control func-

tion. (→P. 54)

●The vehicle is locked/unlocked using the mechanical key. (→P. 539)

39

1-2. Opening, closing and locking the doors

■Electronic key battery depletion

●The standard battery life is 1 to 2 years. (The battery becomes depleted even if the electronic key is not used.) If the smart key system or the wireless remote control function does not operate, or the detection area becomes smaller, the battery may be depleted. Replace the battery when necessary. (→P. 473)

●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field. • TVs • Personal computers • Recharging cellular phones or cordless phones • Table lamps

■To operate the system properly

Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention may not func- tion.)

■Note for the entry function

●Even when the electronic key is within the effective range (detection

areas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.

• The electronic key is on the instrument panel, luggage cover, floor or in the glove box when the engine is started or “ENGINE START STOP” switch modes are changed.

●As long as the electronic key is within the effective range, the doors may

be locked or unlocked by anyone.

●Even if the electronic key is not inside the vehicle, it may be possible to

start the engine if the electronic key is near the window.

40

1-2. Opening, closing and locking the doors

●The doors may unlock if a large amount of water splashes on the door handle, such as in the rain or in a car wash. (The doors will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)

●Gripping the door handle when wearing a glove may not unlock the door. ●If the wireless remote control is used to lock the doors when the elec- tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)

■When the vehicle is not driven for extended periods

To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2
m) of the vehicle. ■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.

■Alarms and warning indicators

A combination of exterior and interior alarms as well as warning lights and warning messages shown on the multi-information display are used to reduce the chance of vehicle theft and accidents resulting from erroneous operation. ●When any warning lights come on:

Take appropriate measures according to which warning light comes on. (→P. 510)

●When a warning message is shown on the multi-information display:

Take appropriate measures according to the warning message on the multi-information display. (→P. 521)

41

1-2. Opening, closing and locking the doors

●When an alarm sounds:

Take appropriate measures according to the following table.

Alarm

Situation

Tried to lock the doors and the glass hatch using the entry function while the electronic key is still inside the passenger compart- ment. Tried to close the glass hatch with the electronic key inside and all doors were locked. Tried to exit the vehicle with the electronic key and lock the doors without first turning the “ENGINE START STOP” switch OFF. Tried to lock the vehicle using the entry function while a door is open. Tried to open the door and exit the vehicle without shifting the shift lever to P. Switched to ACCESSORY mode while the driver's door is open. (Opened the driver's door when the “ENGINE START STOP” switch is in ACCESSORY mode.) Turned the “ENGINE START STOP” switch OFF while the driver's door is open.

Exterior alarm sounds once for 2 seconds

Exterior alarm sounds once for 10 seconds Interior alarm sounds continu- ously

Interior alarm beeps repeatedly

42

Correction procedure Retrieve the elec- tronic key from the passenger compart- ment and lock the doors and the glass hatch again.

Retrieve the elec- tronic key and close the glass hatch.

Turn the “ENGINE START STOP” switch OFF and lock the doors again.

Close all of the doors and lock the doors again.

Shift the shift lever to P.

Turn the “ENGINE START STOP” switch OFF and close the driver's door.

Close the driver's door.

1-2. Opening, closing and locking the doors

Alarm

Situation

Correction procedure

Interior and exte- rior alarms sound continuously.*

Interior alarm beeps once.*

Interior alarm beeps once and exterior alarm sounds 3 times.*

Tried to close the driver’s door after carrying the key outside the vehicle with the “ENGINE START STOP” switch in IGNITION ON or ACCESSORY mode and without the shift lever being in P. The electronic key has a low battery. Tried to start the engine without the electronic key being present, or when the electronic key was not functioning normally. Tried to close the driver’s door after carrying the key outside the vehicle without turning the “ENGINE START STOP” switch OFF. An occupant carried the electronic key outside the vehicle and closed the door when the “ENGINE START STOP” switch was in IGNITION ON or ACCESSORY mode.

Shift the shift lever to P, turn the “ENGINE START STOP” switch OFF and close the driver’s door again.

Replace the electronic key battery.

Start the engine with the electronic key present.

Turn the “ENGINE START STOP” switch OFF and close the driver’s door again.

Bring the electronic key back into the vehi- cle.

*: A message will be shown on the multi-information display.

■If the smart key system does not operate properly

●Locking and unlocking the doors: Use the mechanical key. (→P. 539) ●Starting the engine. (→P. 539)

■When the electronic key battery is fully depleted

→P. 473

43

1-2. Opening, closing and locking the doors

■Customization that can be configured at Toyota dealer

It is possible to deactivate the smart key system etc. (Customizable features →P. 582)

■Certification for the smart key system

For vehicles sold in the U.S.A.

FCC ID: NI4TMLF-3
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver. ●Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

44

1-2. Opening, closing and locking the doors

45

1-2. Opening, closing and locking the doors

46

1-2. Opening, closing and locking the doors

47

1-2. Opening, closing and locking the doors

For vehicles sold in Canada

NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

48

1-2. Opening, closing and locking the doors

49

1-2. Opening, closing and locking the doors

50

1-2. Opening, closing and locking the doors

51

1-2. Opening, closing and locking the doors

52

1

1-2. Opening, closing and locking the doors

CAUTION

■Caution regarding interference with electronic devices

●People with implanted pacemakers or cardiac defibrillators should keep away from the smart key system antennas. (→P. 36) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.

●User of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

Ask your Toyota dealer for details for disabling the entry function.

53

1-2. Opening, closing and locking the doors Wireless remote control

The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle.

Vehicles without smart key system (type A)

and

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pushing Opens and closes power back door Pushing and Opens the glass hatch The glass hatch can be opened only when the back door is closed. Pushing Sounds alarm

holding: the

holding:

holding:

and

54

1-2. Opening, closing and locking the doors

Vehicles without smart key system (type B)

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pushing Sounds alarm Pushing Opens (vehicles with glass hatch) The glass hatch can be opened only when the back door is closed.

holding: the glass hatch

holding:

and

and

Vehicles with smart key system

Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. holding: Pushing Opens and closes the power back door (vehicles with power back door) Pushing Sounds alarm

holding:

and

and

55

1-2. Opening, closing and locking the doors

■Operation signals

Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

Back door: A buzzer sounds and the emergency flashers flash twice to

indicate that the back door has been opened/closed.

■Panic mode

Vehicles without smart key system

When is pushed for longer than about one second, an alarm will sound for about 60 seconds and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, push any button on the wireless remote control.

Vehicles with smart key system

When is pushed for longer than about one second, an alarm will sound for about 60 seconds and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, push any button on the wireless remote control.

■Door lock buzzer

If a door is not fully closed, a buzzer sounds continuously if an attempt to lock the door is made. Fully close the door to stop the buzzer, and lock the vehicle once more.

56

1-2. Opening, closing and locking the doors

■Key battery depletion

Vehicles without smart key system

The standard battery life is 1 to 2 years. (The battery becomes depleted even if the key is not used.) If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (→P. 472)