Download PDF Manual


remote control


is operating a function on


D When the battery is discharged. To re- place the battery, see “—Replacing bat- tery” on page 30 in this Section.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


D When


the electronic key


is near a


high−voltage or noise−emitting device.


together with a key


D When you are carrying an electronic key for another smart key system equipped vehicle or another radio waves.


instrument


emitting


D Depending on the position of the key or vehicle body shape, the key may not work well even within the actuation area.


D When the key surface is covered by a sticker, etc. that may cut off electro- magnetic wave.


Even if the smart key system does not operate properly, you can still enter and start the hybrid system. For further infor- mation, see “Side doors” on page 38 and “Trunk lid” on page 47 in this Section, and see “How to start the hybrid system” on page 301 in Section 3.


function,


the start


STARTING THE HYBRID SYSTEM WHEN THE ELECTRONIC KEY BATTERY IS DISCHARGED If the key indicator does not flash and the hybrid system cannot be started by using the battery may be discharged. Replace the key (See battery as soon as possible. “—Replacing battery” on page 30 in this Section.) However the hybrid system can be turned on in the following procedures. 1. While touch electronic key to the “POWER” switch.


the brake pedal the Toyota


is depressed, the


logo side of


’07Camry hybrid_U (L/O 0610)


2. Start


the hybrid system within 5
seconds after the green indicator light on the “POWER” switch comes on and a buzzer sounds.


BATTERY POWER SAVING Both the vehicle and key transmitters are always sending signals to each other. To prevent battery drain, the smart key sys- tem is automatically deactivated in the fol- lowing conditions: D If the electronic key is left outside of the effective function actuation


the vehicle and within range of area for more than 10 minutes.


the entry


D If the door lock or unlock operation is


not performed more than 2 weeks.


leave the key near


The key and the vehicle are communicat- ing even while the vehicle is not being driven. Do not the vehicle (within 2 m [7 ft.]). the The vehicle battery may drain vehicle is not used for a long period of time. To prevent battery drain, disconnect the battery negative (−) terminal or disable the smart key system. (For details about disable see “DISABLING THE SMART KEY SYSTEM” in this Section.)


system,


smart


key


the


if


35


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


To reactivate the smart key system, per- form any of the following: (a) Press the lock button on the front out- side door handle or trunk open button while carrying the electronic key.


(b) Perform a wireless remote control op-


(c)


eration. Insert and turn the mechanical key in the keyhole of the driver’s door.


If the electronic key receives strong elec- tromagnetic waves over a period of time, the battery can be drastically run down. You should always keep following electrical appliances at least 1 m (3 ft.) away from the electronic key. D TV D Personal computer D Cellular phone or cordless phone re-


the


charger unit


D Electric light stand D Fluorescent desk light


For vehicles sold in U.S.A.


FCC ID: NI4TMLF−2
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


CAUTION


Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.


36


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


For vehicles sold in Canada


This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.


interference,


including


For vehicles sold in U.S.A.


This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


interference


NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures:


to radio or


D Reorient or relocate the receiving an-


tenna.


D Increase the separation between the


equipment and receiver.


D Connect the equipment into an outlet to


on a circuit different which the receiver is connected.


from


that


D Consult the dealer or an experienced


radio/TV technician for help.


FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.


For vehicles sold in Canada


Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.


interference,


including


37


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


DISABLING THE SMART KEY SYSTEM The following functions can be disabled: D A function that allows you to lock/un- lock the doors and open the trunk by simply carrying a key


D A function that causes the vehicle to beep if keys are forgotten inside the vehicle or trunk and a door is closed D A function that recalls the position of the driver’s seat and side rear view mirror


D A function that shifts the power supply mode and starts the hybrid system when the electronic key is in the ve- hicle.


D Warning lights and buzzers For details, contact your Toyota dealer. If the smart key system does not oper- ate properly because of a system mal- function, consult your Toyota dealer. Make sure to bring all of the keys. They may be necessary to repair the system.


38


’07Camry hybrid_U (L/O 0610)


Side doors— —Locking and unlocking with smart key system When you carry the registered key with smart key system into the actuation area, you can lock and unlock the side doors without using the key. For further informa- tion of actuation area, see “Smart key system” on page 32 in this Section.


Locking operation Push the lock button on the front out- side door handle slowly and firmly. All the doors lock simultaneously. At this time one beep will be heard and turn signal lights flash once. For three seconds after the doors have been the doors cannot be un- locked via the smart key system. This feature allows the operator to confirm that the doors are locked. In the following cases, the doors cannot be locked by pushing the lock button and a beep will sound as an indicator.


locked,


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


D When any of the doors are not secure- ly closed. A beep will sound continu- ously for 10 seconds.


D When the lock button is pressed while opening or closing the door. A beep will sound continuously for 10 seconds. D When the hybrid system is not turned off. A beep will sound continuously for 2 seconds.


D When the key is left in the vehicle. A beep will sound continuously for 2 sec- onds.


D When attempting to lock the doors with the key near a window or a door han- dle. A beep will sound continuously for 2 seconds.


The beep may not sound if the key is on the instrument panel, on the package tray, in the glove box or on the floor, etc. The answerback function (the turn signal flash and the beep) can be disabled. For details, contact your Toyota dealer.


Wearing gloves may slow response time. For three seconds after the doors have been locked, the doors cannot be re−un- locked via the smart key system. The answerback function (the turn signal flash and the beep) can be disabled. For details, contact your Toyota dealer. When you enter the entry function actua- tion area, the interior and exterior lights come on for about 15 seconds. After the light comes on, all the side doors can be unlocked by grasping the outside door handle. You have 60 seconds to open a door after using the unlocking function. If a door is not opened by then, all the doors will be automatically locked again. The automatic locking time can also be set to 30 seconds. For details, contact your Toyota dealer. The doors may unlock if the key is within the entry function actuation area and a large amount of water splashes on the door handle (for example, in the rain or in a car wash). When you enter the entry function actua- tion area, the illuminated entry system will be activated. (For further information, see “Illuminated entry system” on page 127 in Section 1−5.)


39


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


Unlocking operation Grasp the front outside door handle (sensors are located on the underside of the door handles). Only the driver’s door unlocks when the driver’s door handle is grasped. All the doors unlock when the front passenger’s door handle is grasped. At this time two beeps will be heard and lights flash twice. The doors may not unlock if the handle is grasped too quickly. Be sure to confirm that the doors are unlocked before pulling the door handle. If the doors do not open when the handle is pulled, return the han- dle to its original position.


the turn signal


’07Camry hybrid_U (L/O 0610)


—Locking and unlocking with inside lock knob


SELECTING DOORS TO BE UNLOCKED WITH ENTRY FUNCTION The unlocking operation has 2 modes. To change the mode, within 1 m (3 ft.) of the vehicle press the lock switch and the alarm, trunk opener or unlock switch simultaneously for five seconds. The “POWER” switch must be turned off. When the mode is changed, the buzzer will sound and an indicator is displayed on the multi−information display as follows:


Mode Door to be unlocked


Wireless remote control buzzer


Indicator and meter


buzzer


All doors


2 beeps


1 beep


only


Driver’s door (from driver’s door switch) doors All (from front passenger’ door switches)


3 beeps


1 beep


Repeating the above process allows you to toggle between 1 and 2.


40


Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handle even if the lock knobs are in the locked position.


CAUTION


Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


—Locking and unlocking with power door lock switch


Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Doors cannot be locked when either front door is open and the key is left in the vehicle.


Driver’s side


Passenger’s side


lock: Push the switch down on the


Push the switch. To right side. To unlock: Push the switch down on the left side. All the doors lock or unlock simultaneous- ly. When the front doors are locked from the outside or locked with the wireless remote control lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control function.


the power door


function,


41


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


—Locking and unlocking door with mechanical key


Insert the mechanical key into the key- hole and turn it. To lock: Turn the key forward. All the doors lock simultaneously with the driver’s door. For three seconds after the doors have been the doors cannot be un- the smart key system. This locked via feature allows the operator to confirm that the doors are locked. To unlock: Turn the key backward. Turning the key once will unlock the driv- er’s door and twice in succession will un- lock all the doors simultaneously.


locked,


42


’07Camry hybrid_U (L/O 0610)


This double key turning operation to un- lock all the doors can be changed to a single key turning operation. For details, contact your Toyota dealer. When you unlock the illumi- nated entry system will be activated. (For further information, see “Illuminated entry system” on page 127 in Section 1−5.)


the doors,


—Automatic door locking and unlocking functions AUTOMATIC DOOR LOCKING You can select the following functions: D Locking linked with the shift position All doors are automatically locked when the selector lever is moved out of “P” position.


D Locking linked with vehicle speed


All doors are automatically locked when the vehicle speed goes above about 20
km/h (12 mph).


You can set or cancel the automatic door locking functions: Be sure to apply the parking brake when performing the following operations.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


To select the locking linked with the shift position: 1. Close all doors and set the “POWER”


To select the locking linked with the vehicle speed: 1. Close all doors and set the “POWER”


switch at ON.


switch at ON.


2. Shift the selector lever to the “P” posi-


2. Shift the selector lever from “P” to the


tion.


“N” position.


turning


3. Within 10 seconds of


the “POWER” switch on, press and hold the driver’s side power door lock switch in the lock position for 5 sec- onds and then release. The doors will be locked and unlocked to indicate that the function is set.


turning


3. Within 10 seconds of


the “POWER” switch on, press and hold the driver’s side power door lock switch in the lock position for 5 sec- onds and then release. The doors will be locked and unlocked to indicate that the function is set.


To cancel the function, do the above op- eration again.


To cancel the function, do the above op- eration again.


AUTOMATIC DOOR UNLOCKING You can select the following functions: D Unlocking linked with the shift posi-


tion All doors are automatically unlocked when the selector lever is moved to “P” position.


D Unlocking linked with the “POWER”


switch All doors are automatically unlocked when the driver’s door is opened within 10 seconds after the “POWER” switch is set from ON to ACC or OFF.


You can set or cancel the automatic door unlocking functions: Be sure to apply the parking brake when performing the following operations.


43


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


To select the unlocking linked with the shift position: 1. Close all doors and set the “POWER”


To select the unlocking linked with the “POWER” switch: 1. Close all doors and turn the “POWER”


switch at ON.


switch at ON.


2. Shift the selector lever to the “P” posi-


2. Shift the selector lever from “P” to the


tion.


“N” position.


—Rear door child−protectors


turning


3. Within 10 seconds of


the “POWER” switch on, press and hold the driver’s side power door lock switch in the unlock position for 5 sec- onds and then release. The doors will be locked and unlocked to indicate that the function is set.


turning


3. Within 10 seconds of


the “POWER” switch on, press and hold the driver’s side power door lock switch in the unlock position for 5 sec- onds and then release. The doors will be locked and unlocked to indicate that the function is set.


To cancel the function, do the above op- eration again.


To cancel the function, do the above op- eration again.


to


the


lock


lever


the “LOCK”


Move position as shown on the label. When the child−protector is locked, you cannot open the rear door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.


44


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Power windows


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle in an accident. It also helps pre- vent the doors from being opened unintentionally.


the


45


even


seconds


The windows can be operated with the switch on each door. The power windows work when “POWER” switch is set at ON. Key off operation: All windows work for about the “POWER” switch is turned off. They stop working when either front door is opened. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Pull up the switch.


after


Automatic operation: Push the switch completely down and then release it. The window will fully open. To stop the window partway, pull the switch up and then re- lease it.


45


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


THE


PASSENGERS’


OPERATING WINDOWS Use the switches on the passengers’ doors. The driver’s door also has switches that control the passengers’ windows. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passengers’ windows cannot be operated.


Window lock switch


46


CAUTION


To avoid death or serious personal injury, you must do the following. D Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.


in a closing window,


the vehicle.


inside


D When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.


them


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


D Never leave anyone (particularly a small child) alone in your vehicle, especially with the “POWER” switch set at ON. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.


trapped


’07Camry hybrid_U (L/O 0610)


Trunk lid— —Opening trunk lid with smart key system


the


When you carry the registered key into the actuation area, trunk can be opened. For further information of actua- tion area, see “Smart key system” on page 32 in this Section. See “—Stowage precautions” on page 295
in Section 2 for precautions when loading luggage. To close the trunk lid, lower it and press down on it. After closing the trunk lid, try pulling it up to make sure it is securely closed.


The trunk lid can be opened with the wire- less remote control function, see “—Open- ing trunk lid” on page 28 in this Section.


CAUTION


Keep the trunk lid closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.


A warning buzzer may sound when: D The key is brought into the cabin after the trunk is opened, and the trunk is then closed.


D The key is near the trunk when the


trunk is closed.


The buzzer may sound even when the key is not in the trunk. This does not indicate a problem. However, under these circum- stances, the trunk cannot be opened using the smart key system. Open trunk using other methods.


the


47


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


switch without


If the trunk is closed with the key left in the trunk when all side doors are locked, a beep will sound continuously for 2 sec- onds. You can open the trunk pushing the trunk opener carrying another key. However, in some instances, the beep may not sound when the trunk is closed depending on the location of the key in the trunk. In addition, when the doors are open or unlocked, the beep may not sound when the trunk is closed. When closing the trunk, make sure that the key is not left in it.


’07Camry hybrid_U (L/O 0610)


—Opening trunk lid by lock release lever


—Opening trunk lid with mechanical key


To open the trunk lid from the driver’s seat, pull up on the lock release lever. To deactivate this lock release lever from opening the trunk lid, see “—Luggage se- curity system” described below.


To open the trunk lid manually from the outside, insert the mechanical key and turn it clockwise.


48


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


—Luggage security system


—Internal trunk release strap


NOTICE


Implement the above steps to maxi- mize security of the luggage in the trunk whenever the vehicle is unat- tended.


lock release


This system helps protect things locked in the trunk by safeguarding the trunk lid lever from unwanted access. Close the trunk lid. Insert the mechani- cal key and turn it counterclockwise to deactivate the trunk lid lock release le- ver. After the operation, try pulling up on the trunk lid lock release lever to make sure it is locked.


is


in


locked


If a person the trunk, he/she can pull up the phosphorescent strap on the inside of trunk lid to open the trunk lid. The (glow−in−the−dark) strap will continue to glow for a time after the trunk lid is closed. Exposing the han- dle to stronger light will cause it to glow longer.


phosphorescent


49


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Hood


CAUTION


D Always lock the trunk lid and all doors, and keep away the vehicle keys out of children’s reach.


D Never leave children unattended in the vehicle. Unsupervised children may lock themselves in the vehicle or trunk and suffer serious injuries or death.


To open the hood: 1. Pull the hood lock release lever. The


hood will spring up slightly.


CAUTION


Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.


2. In front of the vehicle, pull up the the


lever and


lift


auxiliary catch hood.


Before closing the hood, check to see that you have not forgotten any tools, rags, etc. Then lower the hood and make sure it If necessary, press down gently on the front edge to lock it.


into place.


locks


50


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Fuel tank cap—


1. To open the fuel filler door, push the


switch.


This indicates that the fuel filler door is on the left side of your vehicle. To refuel your vehicle, turn the hybrid system off.


CAUTION


Do not smoke, cause sparks or allow open flames in the area when refuel- ing. The fumes are flammable.


If the pressure in the fuel tank is high, a message “PLEASE WAIT NOW OPENING” will appear on the multi−information dis- play. It may take up to 10 seconds if the internal pressure is high. The segments in the display increase to indicate the time left. The segments in the display decrease to indicate the time left. When lowers, a message “REFUEL READY” will appear and the fuel filler door will open. If the fuel filler door does not open, the opener may have a malfunction. For de- tails, see “—If the fuel filler door opener is not actuated” on page 53 in this Sec- tion.


the pressure


51


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


CAUTION


When opening the cap, do not remove the cap quickly. In hot weather, fuel under pressure could cause injury by spraying out of the filler neck if the cap is suddenly removed.


2. Turn the cap slowly counterclockwise


and remove it. The removed cap can be stored on the backside of the fuel filler door.


When reinstalling, turn the cap clockwise until you hear a click. If the cap is not tightened securely, the malfunction indicator lamp will come on. Make sure the cap is tightened securely. The indicator lamp will go off after driving the vehicle several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


If you leave the fuel filler door open and the hybrid system, a message start “CLOSE FUEL LID” will appear on the multi−information display. Make sure the fuel filler door is closed.


CAUTION


D Make sure the cap is installed se- in


curely to prevent fuel spillage the event of an accident.


D Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.


NOTICE


Finish refueling within 30 minutes. If more than 30 minutes passes, the in- ternal valve closes. In this condition, fuel may spill out if you continue to refuel the vehicle. About 5 minutes after the valve is closed, a message “CLOSE FUEL LID” will appear on the multi−information display. To refuel fuel the vehicle again, tank cap and close filler door, and then push the fuel filler door opener switch again.


the fuel


tighten


the


52


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


—If the fuel filler door opener is not actuated


Electric moon roof


1. Open the trunk and remove the cov- er located in the left−hand side of the trunk.


2. Pull the manual lock release lever.


The fuel filler door will open.


the cap slowly counterclock-


3. Turn wise. You may hear a slight swoosh when you remove the cap.


CAUTION


When opening the cap, do not remove it quickly. The fuel may spray out of the filler opening if the cap is sud- denly removed.


Sliding operation


If the opener is not actuated, contact your Toyota dealer to service the ve- hicle. If you must refuel your vehicle, you can open the fuel filler door manu- ally as instructed below. The system to lower internal pressure in the fuel tank may not be functioning so you must turn the cap slowly with releasing the pressure. In addition, fuel may spill out during refueling. Fill the fuel tank carefully and slowly.


Tilting operation


53


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


the


To operate the moon roof, use switches on the overhead console. The moon roof works when the “POWER” switch is set at ON. The sun shade can be opened or closed by hand. Sliding operation— To open: Push and hold the switch for 1
second toward the vehicle’s rear. The roof will open and stop partway 90
mm (3.6 in.) from the fully opened posi- tion. When you push the switch again, the moon roof will open fully. To stop the roof partway, push one of roof switches briefly. As driving with the moon roof opened fully will cause wind throbs, we recommend you to drive with the moon roof partway 90 mm (3.6 in.) from the fully opened position. The sun shade will be opened together with the roof. To close: Push and hold the switch for 1
second toward the vehicle’s front. The roof will fully close automatically. To stop the roof partway, push one of the moon roof switches briefly.


the moon


Tilting operation— To tilt up: Push and hold the “TILT” switch for 1 second on the “UP” side. The roof will fully tilt up automatically. To stop the roof partway, push one of the moon roof switches briefly. To tilt down: Push and hold the “TILT” switch for 1 second on the “DOWN” side. The roof will fully tilt down automatically. To stop the roof partway, push one of the moon roof switches briefly. Open moon roof reminder: If the moon roof the “POWER” switch at ACC or off and open message the “MOONROOF OPEN” appears on the multi−information display and a warning tone sounds. Key off operation: If both front doors are closed, the moon roof works for about 45
seconds even after the “POWER” switch is turned off. It stops working when either door is opened.


left open when you set


driver’s


door,


is


function:


Jam protection If something gets caught between the moon roof and frame during closing operation, the moon roof stops and opens. If the moon roof receives a strong impact, this function may work even if nothing is caught.


CAUTION


To avoid death or serious personal injury, you must do the following. D While the vehicle is moving, always keep the heads, hands and other parts of the bodies of all occupants away from the roof opening. Other- wise, they could be killed or seri- ously injured if the vehicle stops suddenly or in- volved in an accident.


if the vehicle


is


54


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


D The


jam protection


function may not work if something gets caught just before the moon roof is fully closed.


in death or serious


D Before you close the moon roof, always make sure there is nobody around the moon roof. You must also make sure nobody places his or her head, hands and other parts of the body in the roof opening. If someone’s neck, head or hands get caught in the closing roof, it could result injury. When anyone closes the moon roof, first make sure it is safe to do so. D Never leave anyone (particularly a small child) alone in your vehicle, especially with the “POWER” switch set at ON. Otherwise, he/she could use the moon roof switch and get trapped in the roof opening. Unat- tended person (particularly a small child) can be involved in a serious accident.


D Never sit on


top of


the vehicle


around the roof opening.


D Never try jamming any part of your body to activate the jam protection function intentionally, as it could re- sult in a death or serious injury.


55


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


56


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


SECTION 1− 3


OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats Front seats Rear seats Seat heaters Head restraints Armrest Seat belts SRS airbags Child restraint


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


58
58
63
64
65
65
66
77
96


57


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.


CAUTION


D Do not drive the vehicle unless the occupants are properly seated. Do not allow any passengers to sit on top of a folded−down seatback, or in the luggage compartment or car- go area. Persons not properly seated and/or not properly re- strained by seat belts can be killed or severely injured in the event of emergency braking or a collision.


D During driving, do not allow any passengers to stand up or move around between seats. Otherwise, death or severe injuries can occur in the event of emergency braking or a collision.


Front seats— —Front seat precautions Driver seat


CAUTION


The SRS driver airbag deploys with considerable force, and can cause death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises: Since the risk zone for driver airbag is the first 50—75 mm (2—3 in.) of inflation, placing yourself 250 mm (10
in.) from your driver airbag provides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 250
mm in.) away now, you can change your driving position in sever- al ways: D Move your seat to the rear as far as you can while still reaching the pedals comfortably.


(10


58


D Slightly recline


the back of


the seat. Although vehicle designs vary, many drivers can achieve the 250
mm (10 in.) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non−slippery cushion, or raise the seat if your vehicle has that feature.


D If your steering wheel is adjustable, tilt it downward. This points the air- bag toward your chest instead of your head and neck.


The seat should be adjusted as rec- ommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Front passenger seat


Front seats


CAUTION


CAUTION


The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury es- pecially if the front passenger is very close to the airbag. The front passen- ger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright.


The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. D Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or seriously in- jured.


D Do not use seat accessories which cover the area where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.


D Do not modify or replace the seats or upholstery of the seats. Such change may prevent the side airbag system from activating correctly, disable the system, or cause the side airbags to inflate accidentally, resulting in death or serious injury.


—Seat adjustment precautions


CAUTION


D Do not adjust the seat while the vehicle is moving as the seat may unexpectedly move and cause the driver to lose control of the vehicle. D Be careful that the seat does not


hit a passenger or luggage.


D After adjusting the seat position, re- lease the lever and try sliding the seat forward and backward to make sure it is locked in position.


D After adjusting the seatback, push your body back against the seat to make sure the seat in position.


locked


is


D Do not put objects under the seats. Otherwise, the objects may interfere with the seat−lock mechanism or unexpectedly push up the seat posi- tion adjusting lever and the seat may suddenly move, causing the driver to lose control of the vehicle.


59


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


D While adjusting the seat, do not put your hands under the seat or near the moving parts. Otherwise, your hands or fingers may be caught and injured.


’07Camry hybrid_U (L/O 0610)


—Adjusting driver’s seat


1. SEAT POSITION AND SEAT HEIGHT


ADJUSTING SWITCH


Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under the seat, as this might interfere with the seat move- ment. 2. SEATBACK


ADJUSTING


ANGLE


SWITCH


Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position.


60


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


—Adjusting front passenger’s seat (manual seat)


1. SEATBACK


LEVER


ANGLE


ADJUSTING


lever up. lean back to the desired angle


Lean forward and pull the Then and release the lever. 2. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever.


CAUTION


reclining


Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or serious injury.


3. SEAT


LUMBAR ADJUSTING SWITCH


SUPPORT


Push the control switch in the desired direction. The amount of lumbar support will change while the switch is pushed.


61


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


CAUTION


reclining


Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or serious injury.


62


’07Camry hybrid_U (L/O 0610)


—Adjusting front passenger’s seats (power seat)


1. SEATBACK


SWITCH


ANGLE


ADJUSTING


Move the control switch in the desired direction. Releasing the switch will stop the seat- back at that position. 2. SEAT POSITION ADJUSTING SWITCH Move the control switch in the desired direction. Releasing the switch will stop the seat at that position. Do not place anything under the seat, as this might interfere with the seat move- ment.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Rear seats— —Fold−down rear seat


FOLDING DOWN REAR SEAT 1. To unlock the seatback, pull the le-


ver in the trunk.


2. Fold down the seatback. Each seatback can be folded separately. This will enlarge the trunk as far as the seatbacks. See “—Stowage precautions” on page 295 in Section 2 for precautions when loading luggage.


NOTICE


Make sure the luggage loaded in the enlarged trunk will not damage the webbing of the rear center seat belt when folded down.


left seatback


the


is


CAUTION


When returning the seatback to the upright position, observe the follow- ing precautions in order to prevent death or serious injury in a collision or sudden stop: D Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.


D Make sure the seat belts are not twisted or caught in the seatback and are arranged the proper position and are ready to use.


in


63


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Seat heaters


CAUTION


NOTICE


z Do not put unevenly weighed ob- jects on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.


z When cleaning the seats, do not use organic substances (paint thin- ner, benzine, alcohol, gasoline, etc.). They may damage the heater and seat surface.


z To prevent the 12 volt battery from being discharged, turn the switch off when is turned off.


the hybrid system


the seat heater because


Occupants must use caution when op- erating it may make them feel too hot or cause burns at low temperatures (erythema, varicella). Use extra caution for the following: D Babies, small children, elderly per- sons, sick persons or persons with physical disabilities


D Persons who have sensitive skin D Persons who are exhausted D Persons who have taken alcohol or drugs which induce sleep (sleeping drug, cold remedy, etc.)


To prevent the seat overheating, do not use the seat heater with a blan- ket, cushion, or other insulating ob- jects which cover the seat.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


To turn on the seat heater, push the switch. At this time, the indicator light will illuminate to indicate the seat heat- er is operating. To turn off the seat heater, push the switch once again. The “POWER” switch must be set at ON to operate seat heaters.


64


’07Camry hybrid_U (L/O 0610)


Head restraints


Armrest


Front


Rear


For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. Rear center head restraint—When an oc- cupant sits on the rear center seat, al- ways pull up the rear center head re- straint to the lock position. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.


CAUTION


To use shown above.


the armrest, pull


it out as


D Adjust the center of the head re- straint so that it is closest to the top of your ears.


D After adjusting the head restraint, make sure it is locked in position. the head re-


D Do not drive with


straints removed.


65


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Do not allow any children to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. Holding a child in your arms does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.


recommendations. The


Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. The seat belts provided for your vehicle are designed for people of adult size, large enough to properly wear them. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” on page 96 in this Section for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.


66


CAUTION


the vehicle


D Avoid reclining


in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: D Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may In the contact the shoulder belt. event of a the more the seat is reclined, the great- er the risk of death or serious inju- ry.


frontal collision,


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


D Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.


D Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.


—Fastening front and rear seat belts


Tab


Buckle


D Keep the belts clean and dry.


If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers, or allow them to come into the belts—they may contact with severely weaken (See “Cleaning the interior” on page 336
in Section 5.)


the belts.


D Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.


tab


the


into


insert


Adjust the seat as needed and sit up straight and well back in the seat. To fasten your belt, pull it out of the re- tractor and the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.


is


then


When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” on page 96 in this Section.) To free the belt again, fully retract the belt and then pull the belt out once more. If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor.


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious injury.


67


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


Take up slack


Too high


CAUTION


D Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on hips as possible.


D Do not place the shoulder belt un-


der your arm.


Keep as low on hips as possible


the


lap and


the position of


Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.


68


Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment make sure the anchor is locked in position.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


CAUTION


Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injures in a colli- sion.


CAUTION


D Always make sure the shoulder belt passes through the guide when us- ing the seat belt. Failure to properly position the belt may reduce the amount of protection in an accident and could lead to serious injures in a collision or sudden stop.


D Always make sure that the seat belt is not twisted, does not get caught in the guide or the seatback and is arranged in the proper position.


Rear seat belts— Use the seat belt after passing it through the guide if the seat belt comes free from the guide.


69


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


—Seat belt comfort guides


To release the belt, press the buckle release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.


The outside shoulder belt comfort guides for the rear seat outside posi- tions will provide added seat belt com- fort for children who have outgrown child restraints and for small adults. When the outside shoulder belt is in- serted through the guide, the comfort guide pulls the belt away from the neck and head of an occupant. To use the comfort guide, do as fol- lows.


Seat belt comfort guides are stored in the both pockets on the rear seatback.


the sides of


70


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


INSTALLING THE COMFORT GUIDE 1. Pull out the comfort guide from the


pocket.


2. Pinch the two edges of the shoulder belt for the rear seat outside posi- tion with your fingers and slide the belt past the slot of the guide as shown above. At this time, the elas- tic cord must be behind the seat belt.


CAUTION


Make sure the belt is not twisted and that it lies flat. The elastic cord must be behind the guide must be on the front.


the belt and


3. Buckle, position and release the seat belt. (For wearing the seat belt, see “—Fastening rear seat belts” on page 67 in this Section.)


front and


CAUTION


Always make sure the shoulder belt is positioned across the center of the shoulder. The belt should be kept away from the neck, and should not fall off the shoulder. Failure to ob- serve these precautions could reduce the effectiveness of the seat belt in an accident, causing death or serious injury.


71


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


’07Camry hybrid_U (L/O 0610)


from your Toyota dealer


—Seat belt extender If your seat belts cannot be fastened se- curely because they are not long enough, a personalized seat belt extender is avail- able free of charge. Please contact your local Toyota dealer to order the proper required length for the extender. Bring the heaviest coat you ex- pect to wear for proper measurement and selection of length. Additional ordering in- formation is available at your Toyota deal- er.


CAUTION


the


When using the seat belt extender, following precautions. observe Failure to follow these instructions could reduce the effectiveness of the seat belt restraint system in case of an accident, increasing the chance of death or serious injury. D Remember that the extender pro- vided for you may not be safe when used on a different vehicle, for another person, or at a different seating position than the one origi- nally intended.


in


the extender


D If the seat belt extender has been connected to the driver’s seat belt buckle without wearing the seat belt when using the driver’s seat, the SRS driver’s air- bag system will judge that the driv- er wears the seat belt even if not wearing it. In this case, the driver’s airbag may not activate correctly, causing death or serious injury in the event of collision. Be sure to wear the seat belt with the seat belt extender.


2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)


THE


AND


STORING


REMOVING COMFORT GUIDE Pinch the two edges of the seat belt together so that you can slide them out of the guide. Store the guide with the elastic cord into the pocket.


CAUTION


To reduce the chance of in case of an accident or a sudden stop while driving, remove and store the comfort guide in its pocket when it is not in use.


injury


Loading...
x