Download PDF Manual

8) Wiper control lever (page 3-29) 9) Cruise control (page 7-31) 10) Horn (page 3-37) 11) SRS airbag (page 1-45) 12) Tilt steering (page 3-37) 13) Hood lock release knob (page 11-4) 14) Fuse box (page 11-38) 15) Power windows (page 2-19)


– CONTINUED –


A3120BE-B.book 16 ページ 2006年5月30日 火曜日 午前9時32分


16


(cid:132) Light control and wiper control levers/switches


11


10


000107


1) Parking light switch (page 3-28) 2) Windshield wiper (page 3-29) 3) Mist (page 3-31) 4) Windshield washer (page 3-30) 5) Rear window wiper and washer


switch (page 3-32)


6) Wiper control lever (page 3-30) 7) Light control lever (page 3-26) 8) Fog light switch (page 3-29) 9) Headlight ON/OFF (page 3-26) 10) Headlight flasher High/Low beam


change (page 3-26)


11) Turn signal (page 3-27)


A3120BE-B.book 17 ページ 2006年5月30日 火曜日 午前9時32分


(cid:132) Combination meter (cid:84) U.S.-spec. vehicles


17


1) Temperature gauge (page 3-9) 2) Tachometer (page 3-8) 3) Speedometer (page 3-7) 4) Fuel gauge (page 3-8) 5) Trip meter and odometer (page 3-7/


page 3-7)


6) Trip meter A/B selection and trip


meter reset knob (page 3-7)


7) Selector lever/Gear position indicator


(page 3-20)


x1000r/min


R. DIFF TEMP


SPORT


BRAKE


AT OIL TEMP ABS


AIR BAG


CRUSE SET


DRL


AWD


CHECK ENGINE


60


80
100 120 140


40


80


60


40


20
km/h


20


100
160


180


120
200


220
140


240


MPH


000225


– CONTINUED –


A3120BE-B.book 18 ページ 2006年5月30日 火曜日 午前9時32分


18


(cid:84) Canada-spec. vehicles


x1000r/min


R. DIFF TEMP


SPORT


BRAKE


ABS


DRL


AT OIL TEMP


AIR BAG


CRUSE SET


AWD


CHECK ENGINE


100120


140


160
100


80


40


20


MPH


60
40
20


60


80


180
120


200
220
140
240
km/h


000226


1) Temperature gauge (page 3-9) 2) Tachometer (page 3-8) 3) Speedometer (page 3-7) 4) Fuel gauge (page 3-8) 5) Trip meter and odometer (page 3-7/


page 3-7)


6) Trip meter A/B selection and trip


meter reset knob (page 3-7)


7) Selector lever/Gear position indicator


(page 3-20)


A3120BE-B.book 19 ページ 2006年5月30日 火曜日 午前9時32分


(cid:132) Warning and indicator light


Mark


Name


Page


Mark


Name


Mark


Name


Driver’s seatbelt warn- ing light


Front passenger’s seatbelt warning light


SRS airbag system warning light


CHECK ENGINE warning light/Malfunc- tion indicator lamp


Page


3-10


3-10


3-11


3-13


Charge warning light


3-13


Oil pressure warning light


AT OIL temperature warning light


3-13


3-14


or


ABS warning light


3-16


or Brake system warning


light


Door open warning light


3-16


3-17


Low fuel warning light


3-17


All-Wheel Drive warn- ing light


Vehicle Dynamics Control operation indi- cator light


Vehicle Dynamics Control warning light / Traction Control sys- tem OFF indicator light


3-18


3-18


3-18


Security indicator light


3-19


Turn signal indicator lights


High beam indicator light


Front fog light indicator light


Headlight indicator light


or Daytime running light


indicator light


3-20


3-20


3-21


3-21


3-21


Cruise control indica- tor light


Cruise control set indi- cator light


tire


Low warning light


pressure


Passenger airbag ON indicator light


Passenger airbag OFF indicator light


SPORT mode indica- tor light


Windshield washer flu- id warning light


Rear differential oil temperature warning light


19


Page


3-20


3-21


3-14


3-12


3-12


3-20


3-18


3-14


– CONTINUED –


Jack handle (page 9-20)


1) 2) Maintenance tools (page 9-20) 3) 4) Spare tire (page 9-2)


Jack (page 9-20)


A3120BE-B.book 20 ページ 2006年5月30日 火曜日 午前9時32分


20


(cid:132) Cargo area (cid:84) 7-seater models


000089


A3120BE-B.book 21 ページ 2006年5月30日 火曜日 午前9時32分


(cid:84) 5-seater models


21


Jack handle (page 9-20) Jack (page 9-20)


1) 2) 3) Maintenance tools (page 9-20) 4) Spare tire (page 9-2)


000148


A3120BE-B.book 22 ページ 2006年5月30日 火曜日 午前9時32分


22


Function settings


A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with navigation system, the settings for some of these functions can be changed using the monitor. For details, please refer to the Owner’s Manual supplement for the monitor.


Item


Alarm system


Function


Alarm system


Possible settings


Operation / Non-operation


Monitoring start delay time (after closure of doors)


0 second / 30 seconds


Default setting


Page


Operation


30 seconds


2-14


2-16


Impact sensor operation (only vehicles with shock sensors (dealer option))


Operation / Non-operation


Non-operation


2-18


Passive arming


Operation / Non-operation


Non-operation


2-17


Remote keyless entry system


Hazard warning flasher


Operation / Non-operation


Key lock-in prevention


Key lock-in prevention


Operation / Non-operation


Audible signal


Operation / Non-operation


Operation


Operation


Operation


Rear window defogger


Rear window defogger


Windshield wiper deicer


Windshield wiper deicer (if equipped)


Map light/Dome light


Battery drainage prevention func- tion


Operation for 15 minutes / Continuous op- eration


Operation for 15 minutes


Operation for 15 minutes / Continuous op- eration


Operation for 15 minutes


Operation in interlock with remote keyless entry system


OFF / Short / Normal / Long


Normal


Battery drainage prevention function


Operation / Non-operation


Operation


2-8


2-10


2-6


3-33


3-33


6-2


2-6


A3120BE-B.book 1 ページ 2006年5月30日 火曜日 午前9時32分


Seat, seatbelt and SRS airbags


System servicing .................................................... Precautions against vehicle modification ............


1-30
1-30
Child restraint systems ...................................... 1-31
1-32
1-34


Where to place a child restraint system ............... Choosing a child restraint system ........................ Installing child restraint systems with A/ELR


seatbelt .................................................................. Installing a booster seat ......................................... Installation of child restraint systems by use of lower and tether anchorages (LATCH) ............... Top tether anchorages ........................................... *SRS airbag (Supplemental Restraint System


1-34
1-38


1-39
1-42


airbag) .............................................................. 1-45
1-45
Your vehicle’s SRS configuration ......................... 1-50
Subaru advanced frontal airbag system .............. 1-60
SRS side airbag and SRS curtain airbag .............. 1-70
SRS airbag system monitors ................................. SRS airbag system servicing ................................ 1-71
1-72
Precautions against vehicle modification ............


Front seats .......................................................... Power seat ............................................................... Memory function


(Driver’s seat only – if equipped) ........................ Head restraint adjustment ..................................... Active head restraint .............................................. Lumbar support ...................................................... Seat heater (if equipped) ................................... Rear seats (5-seater models)/Second-row


1-2
1-3


1-4
1-5
1-6
1-6
1-7


seats (7-seater models) .................................. Fore and aft adjustment ......................................... Reclining the seatback ........................................... Folding down the seatback .................................... Head restraint adjustment ..................................... Armrest ....................................................................


1-7
1-8
1-9
1-10
1-11
1-12
Third-row seat (7-seater models) ...................... 1-12
1-13
1-14
1-15
Seatbelts ............................................................. 1-16
1-16
1-17


Access to the third-row seat .................................. Folding down the seatback .................................... Head restraint adjustment .....................................


Seatbelt safety tips ................................................. Emergency Locking Retractor (ELR) .................... Automatic/Emergency Locking Retractor


(A/ELR) .................................................................. Seatbelt warning light and chime .......................... Fastening the seatbelt ............................................ Seatbelt maintenance .............................................


1-17
1-18
1-19
1-27
Front seatbelt pretensioners ............................. 1-28
1-29


System monitors ....................................................


A3120BE-B.book 2 ページ 2006年5月30日 火曜日 午前9時32分


1-2 Seat, seatbelt and SRS airbags


Front seats


Seat, seatbelt and SRS airbags


(cid:121) Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury.


(cid:121) Before adjusting the seat, make sure the hands and feet of rear seat passengers or luggage are clear of the adjusting mechanism. (cid:121) Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. To reduce the risk of sliding under the seatbelt in a collision, the front seatbacks should be always used in the upright position while the vehicle is running. If the front seatbacks are not used in the up- right position in a collision, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death.


(cid:121) The SRS airbags deploy with con- siderable speed and force. Occu- pants who are out of proper posi- tion when the SRS airbag deploys could suffer very serious injuries. Because the SRS airbag needs enough space for deployment, the driver should always sit upright and well back in the seat as far from the steering wheel as practi- cal while still maintaining full ve- hicle control and the front passen- ger should move the seat as far back as possible and sit upright and well back in the seat.


100350


Put children aged 12 and under in a rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, es- pecially if they are 12 years of age and under and are not restrained or improperly restrained. Because chil- dren are lighter and weaker than adults, their risk of being injured from deployment is greater. Conse- quently, we strongly recommend that ALL children (including those in child seats and those that have out- grown child restraint devices) sit in a REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropri- ate for the child’s age, height and weight. Always secure ALL types of child re- straint devices (including forward facing child seats) in one of the rear seating positions recommended in this owner’s manual.


A3120BE-B.book 3 ページ 2006年5月30日 火曜日 午前9時32分


NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly re- strained in the rear seating posi- tions than in the front seating posi- tions. For instructions and precau- tions concerning child restraint sys- tems, see the “Child restraint sys- tems” section in this chapter.


(cid:132) Power seat (cid:84) Fore and aft adjustment


100351


To adjust the seat forward or backward, move the control switch forward or back- ward. NOTE During backward-forward adjustment of the seat, you cannot adjust the seat cushion angle or seat height.


(cid:84) Reclining the seatback


Seat, seatbelt and SRS airbags 1-3


To prevent the passenger from slid- ing under the seatbelt in the event of a collision, always put the seatback in the upright position while the ve- hicle is in motion. Also, do not place objects such as cushions between the passenger and the seatback. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious inter- nal injury or death.


100085


To adjust the angle of the seatback, move the control switch.


100354


– CONTINUED –


A3120BE-B.book 4 ページ 2006年5月30日 火曜日 午前9時32分


1-4 Seat, seatbelt and SRS airbags


(cid:84) Seat cushion angle adjustment


(Driver’s seat only)


(cid:84) Seat height adjustment (Driver’s


seat only)


(cid:84) Registration of seat position


100352


To adjust the seat cushion angle, pull up or push down the front end of the control switch.


(cid:121) Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury.


(cid:121) Before adjusting the seat, make sure the hands and feet of rear seat passengers or luggage are clear of the adjusting mechanism.


100353


1. With the transmission selector lever in the “P” position, adjust the seat position.


To adjust the seat height, pull up or push down the rear end of the control switch.


(cid:132) Memory function (Driver’s


seat only – if equipped)


Two of your favorite seat positions can be registered. Register the seat position with button “1” or “2” and retrieve the seat po- sition by pressing either button.


The following seat positions can be regis- tered: (cid:121) Forward/backward position of the seat (cid:121) Angle of seatback (cid:121) Angle of seat cushion (cid:121) Height of seat


SET


100804


2. While pressing the “SET” button, press the desired button “1” or “2”. 3. The chime sounds once, and the seat position is registered.


A3120BE-B.book 5 ページ 2006年5月30日 火曜日 午前9時32分


(cid:84) Retrieval of seat position


(cid:121) Never retrieve the seat position while driving to avoid the possibil- ity of loss of vehicle control and of personal injury.


(cid:121) Perform the seat position retrieval before driving. Be sure to confirm that the selector lever position is in the “P” position. Do not drive until the retrieval of the seat posi- tion is complete.


(cid:121) Be sure to press the correct but- ton to retrieve your registered seat position. If the seat position is not optimum for you, it may ad- versely affect your driving and may reduce the effectiveness of the seatbelt. That could result in an accident involving serious in- jury or death.


(cid:121) When retrieving a registered seat position, make sure the hands, feet and possessions of rear seat passengers are clear of the seat adjusting mechanism.


Seat, seatbelt and SRS airbags 1-5


NOTE (cid:121) If a new position is registered for the same button, the previous seat posi- tion is deleted. (cid:121) Even if the battery is disconnected, the registered seat position is not de- leted.


(cid:132) Head restraint adjustment


(cid:121) When any trouble or a malfunc- tion occurs during the retrieval of the seat position, stop the retriev- al of the seat position using any of the control switches for manual adjustment, seat memory set but- ton, seat memory registered but- ton 1 or 2.


SET


100805


1. With the transmission selector lever in the “P” position, press the desired button “1” or “2”. 2. The chime sounds once and the seat moves to the registered position. 3. When the seat moves to the registered position, the chime sounds twice.


100355


To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback. The head restraint should be adjusted so that the center of the head restraint is clos- est to the top of the occupant’s ears.


– CONTINUED –


A3120BE-B.book 6 ページ 2006年5月30日 火曜日 午前9時32分


1-6 Seat, seatbelt and SRS airbags


Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.


(cid:132) Active head restraint


100089


The front seats of your vehicle are equipped with active head restraints. They automatically tilt forward slightly in the event the vehicle is struck from the rear, decreasing the amount of rearward head movement and thus reducing the risk of whiplash. For maximum effectiveness the head restraint should be adjusted so that


the center of the head restraint is closest to the top of the occupant’s ears.


(cid:132) Lumbar support


(cid:121) Each active head restraint is ef- fective only when its height is properly adjusted and the driver/ passenger sits in the correct posi- tion on the seat.


(cid:121) If your vehicle is involved in a rear-end collision, have an autho- rized SUBARU dealer inspect the active head restraints.


(cid:121) The active head restraints may not operate in the event the vehi- cle experiences only a slight im- pact in the rear.


(cid:121) The active head restraints may be damaged if they are pushed hard from behind or subjected to shock. As a result, they may not function if the vehicle suffers a rear impact.


100356


Pull the lever forward or backward. Pulling the lever forward will increase the amount of support for your lower back.


A3120BE-B.book 7 ページ 2006年5月30日 火曜日 午前9時32分


Seat heater (if equipped)


ed.


When the vehicle’s interior is warmed enough or before you leave the vehicle, be sure to turn the switch off.


(cid:121) There is a possibility that people with delicate skin may suffer slight burns even at low tempera- tures if they use the seat heater for a long period of time. When us- ing the heater, always be sure to warn the persons concerned.


(cid:121) Do not put anything on the seat which insulates against heat, such as a blanket, cushion, or similar items. This may cause the seat heater to overheat.


NOTE Use of the seat heater for a long period of time while the engine is not running can cause battery discharge.


100357


The seat heater is equipped in the front seats.


The seat heater operates when the igni- tion switch is in the “ON” position.


The seat heater can be adjusted in three levels. Press the button to activate the seat heater. Each subsequent press of the button will reduce the level. Pushing the button four times or keeping the button pressed for approximately 1 second will turn the heater off. While the seat heater is operating, its operating level is shown by the number of illuminated indicators. To warm the seat as quickly as possible, set the heater with three indicators illuminat-


Seat, seatbelt and SRS airbags 1-7


Rear seats (5-seater models)/ Second-row seats (7-seater models)


100358


(cid:121) Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will in- crease, and both can result in se- rious internal injury or death.


– CONTINUED –


A3120BE-B.book 8 ページ 2006年5月30日 火曜日 午前9時32分


1-8 Seat, seatbelt and SRS airbags


(cid:121) Before adjusting the seat, make sure the hands and feet of the rear seat passengers are clear of the adjusting mechanism (7-seater models only).


(cid:84) 7-seater models


Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident.


Never adjust the seat while driving. Doing so is dangerous as the seat could move rapidly and you could be injured.


(cid:132) Fore and aft adjustment (cid:84) 5-seater models


Pull the lever upward and slide the seat to the desired position.


100359


100359


100094


Pull the lever upward and slide the seat to the desired position. Then release the le- ver and move the seat back and forth to make sure that it is securely locked into place.


When the right seat or the left seat pair is slid rearward, it stops partway at the lock


100384


A3120BE-B.book 9 ページ 2006年5月30日 火曜日 午前9時32分


point so as not to trap the legs of passen- gers sitting on the third-row seat. It is possible to slide the seat or seat pair further rearward by releasing the lock that stops it. To do this, simultaneously pull the lever under the outboard seat cushion and turn the lever on the side of the seat cush- ion outward when sliding the seat or seat pair. Once you have released the lock, you can slide the seat or seat pair back and forth with only the lever under the seat cushion pulled. If you slide the seat or seat pair for- ward of the lock point, you will need to re- lease the lock again before you can slide it behind the point. Then release the lever and move the seat back and forth to make sure that it is se- curely locked into place.


If you slide the seat or seat pair aft of the lock point while the third-row seat is occupied, be careful not to trap the legs of the third-row pas- sengers.


(cid:132) Reclining the seatback


Seat, seatbelt and SRS airbags 1-9


(cid:121) In a 7-seater model vehicle, never allow the third-row seat passen- gers to adjust the seatback of the second row. Doing so is danger- ous as the seatback will tilt rapidly and could injure the passengers. is equipped, be careful not to pinch your hand between the headrest and the cargo area cover when you recline the rear seat.


the cargo area cover


(cid:121) If


100360


Pull the lever up and adjust the seatback to the desired position. Then release the lever and make sure the seatback is securely locked into place.


– CONTINUED –


100085


To prevent the passenger from slid- ing under the seatbelt in the event of a collision, always put the seatback in the upright position while the ve- hicle is in motion. Also, do not place objects such as cushions between the passenger and the seatback. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious inter- nal injury or death.


A3120BE-B.book 10 ページ 2006年5月30日 火曜日 午前9時32分


1-10 Seat, seatbelt and SRS airbags


(cid:132) Folding down the seatback


(cid:121) After returning the seat to its orig- inal position, be certain to place all of the seatbelts and the tab at- tached to the seat cushion above the seat cushion. And make cer- tain that the shoulder belts are ful- ly visible.


(cid:121) Never allow passengers to ride on the folded seatback or in the car- go area. Doing so may result in se- rious injury or death.


(cid:121) Secure skis and other lengthy items properly to prevent them from being thrown around inside the vehicle and causing serious injury during a sudden stop, a sudden steering maneuver or a rapid acceleration.


(cid:121) If passengers are sitting on the third-row seat, never drive while folding the second-row seat. It can be a serious interference at the time of braking and impact.


(cid:121) If passengers are sitting on the third-row seat, never drive while the center seatback of the sec- ond-row seat is folded. Doing so may result in serious injury in the event of a hard braking or an im- pact.


100361


1. Slide the seat or seat pair to its rear- most position. 2. Lower the head restraint to its lowest position. 3. Unlock the seatback by pulling the le- ver and then fold the seatback down. 4. To return the seatback to its original position, raise the seatback until it locks into place. Make sure it is securely locked.


100366


By pulling the tab on the center seat, you can fold only the seatback of the center seat. To return the seatback to its original posi- tion, raise the seatback until it locks into place. Make sure it is securely locked.


A3120BE-B.book 11 ページ 2006年5月30日 火曜日 午前9時32分


NOTE


(cid:84) Window side seats


Seat, seatbelt and SRS airbags 1-11


The head restraint is not intended to be used at the lowest position. Be- fore sitting on the seat, raise the head restraint to an appropriate po- sition depending on your sitting height.


100681


1) Bar


(cid:121) Folding the seatback of the center seat will expose the bar that re- tains it in the raised position. Be careful not to hurt yourself on it. Especially, do not rest your finger on the bar. Otherwise, when the seatback is raised, your finger could be pinched between the bar and seatback and thus injured.


(cid:121) Raise the seatback of the center seat while taking care not to trap your hands or other parts of the body between the center seat and window-side seat.


100362


1) Holder


With the seatback folded, attach the tongue plate of each rear/second-row seatbelt to the corresponding holder. Do the same also before someone gets into the third-row seat.


(cid:132) Head restraint adjustment


Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.


100363


To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback. The head restraint should be adjusted so that the center of the head restraint is clos- est to the top of the occupant’s ears. When the seats are not occupied, lower


– CONTINUED –


A3120BE-B.book 12 ページ 2006年5月30日 火曜日 午前9時32分


1-12 Seat, seatbelt and SRS airbags


the head restraints to improve rearward visibility. (cid:84) Center seat


The head restraint is not intended to be used at the lowest position. Be- fore sitting on the seat, raise the head restraint to an appropriate po- sition depending on your sitting height.


100364


To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback.


The head restraint should be adjusted so


that the center of the head restraint is clos- est to the top of the occupant’s ears. When the center seat is not occupied, low- er the head restraint to improve rearward visibility.


(cid:132) Armrest


Third-row seat (7-seater models)


100367


To lower the armrest, pull on the strap of the armrest.


100675


To avoid the possibility of serious injury, passengers must never be al- lowed to sit on the center armrest while the vehicle is in motion.


Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the ab- domen will increase, and both can result in serious internal injury or death.


A3120BE-B.book 13 ページ 2006年5月30日 火曜日 午前9時32分


In its slid-forward position with the seatback tipped forward, the sec- ond-row seat behind the front pas- senger seat is not locked and free to move. Do not drive the vehicle with the seat in this state or allow anyone to sit on the seat unless it is com- pletely locked. Doing so may result in serious injury or death.


When getting into or out of the third- row seat, make sure the second-row seat is in the completely slid-for- ward position and be sure to watch your step.


100094


Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident.


(cid:132) Access to the third-row seat There is a lever on the side of the second- row seat behind the front passenger’s seat. This lever is used to facilitate access to the third-row seat.


Seat, seatbelt and SRS airbags 1-13


(cid:84) To access the third-row seat


100368


Raise the lever. The seatback of the sec- ond-row seat will tip forward and the seat will slide forward. Before driving the vehicle, adjust the fore/ aft position of the second-row seat, raise the seatback, and make sure the seatback is securely locked in position.


– CONTINUED –


A3120BE-B.book 14 ページ 2006年5月30日 火曜日 午前9時32分


1-14 Seat, seatbelt and SRS airbags


(cid:84) To get out from the third-row seat


(cid:132) Folding down the seatback


(cid:121) After returning the seat to its orig- inal position, be certain to place all of the seatbelts and the tab at- tached to the seat cushion above the seat cushion. And make cer- tain that the shoulder belts are ful- ly visible.


(cid:121) Never allow passengers to ride on the folded seatback or in the car- go area. Doing so may result in se- rious injury or death.


(cid:121) Secure skis and other lengthy items properly to prevent them from being thrown around inside the vehicle and causing serious injury during a sudden stop, a sudden steering maneuver or a rapid acceleration.


100677


Raise the lever from the third-row seat. The seatback of the second-row seat will tip forward and the seat will slide forward. Before driving the vehicle, adjust the fore/ aft position of the second-row seat, raise the seatback, and make sure the seatback is securely locked in position.


100369


Place the head restraint in its lowest posi- tion, pull up the lever to release the seat- back lock, and fold down the seatback. To return the seatback to its original posi- tion, raise the seatback until it locks into place. Make sure it is securely locked.


A3120BE-B.book 15 ページ 2006年5月30日 火曜日 午前9時32分


NOTE


100647


1) Holder


(cid:121) Before folding or raising the seat- back of the third-row seat, confirm that the seatbelt is flat against the sidewall at the lower point and the webbing is attached to the holder. (cid:121) When raising the seatback of the third-row seat, if the seatbelt catches on the seatback, hold the belt forward of the seatback while latching the seat- back.


(cid:132) Head restraint adjustment


the head restraints to improve rearward visibility.


Seat, seatbelt and SRS airbags 1-15


Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.


The head restraint is not intended to be used at the lowest position. Be- fore sitting on the seat, raise the head restraint to an appropriate po- sition depending on your sitting height.


100371


To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback. The head restraint should be adjusted so that the center of the head restraint is clos- est to the top of the occupant’s ears. When the seats are not occupied, lower


A3120BE-B.book 16 ページ 2006年5月30日 火曜日 午前9時32分


1-16 Seat, seatbelt and SRS airbags


Seatbelts


(cid:132) Seatbelt safety tips


(cid:121) All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Otherwise, the possibility of serious injury becomes greater in the event of a sudden stop or accident.


(cid:121) All belts should fit snugly in order to provide full restraint. Loose fit- ting belts are not as effective in preventing or reducing injury.


(cid:121) Each seatbelt is designed to sup- port only one person. Never use a single belt for two or more per- sons – even children. Otherwise, in an accident, serious injury or death could result.


(cid:121) Replace all seatbelt assemblies including retractors and attaching hardware worn by occupants of a vehicle that has been in a serious accident. The entire assembly should be replaced even if dam- age is not obvious.


(cid:121) Put children aged 12 and under in a rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12
years of age and under and are not restrained or improperly re- strained. Because children are lighter and weaker than adults, their risk of being injured from de- ployment is greater. Consequent- ly, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devices) sit in a REAR seat properly re- strained at all times in a child re- straint device or in a seatbelt, whichever is appropriate for the child’s height and weight. Always secure ALL types of child restraint devices (including for- ward facing child seats) in one of the rear seating positions recom- mended in this owner’s manual.


NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly restrained in the rear seating posi- tions than in the front seating po- sitions. For instructions and pre- cautions concerning the child re- straint system, see the “Child re- straint systems” section in this chapter.


Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seatbelt(s) by the driver and front passenger when any of the SRS frontal, side and curtain airbags deploy. (cid:84) Infants or small children Use a child restraint system that is suit- able for your vehicle. See information on “Child restraint systems” in this chapter. (cid:84) Children If a child is too big for a child restraint sys- tem, the child should sit in the rear seat


A3120BE-B.book 17 ページ 2006年5月30日 火曜日 午前9時32分


and be restrained using the seatbelts. Ac- cording to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. Never allow a child to stand up or kneel on the seat.


If the shoulder portion of the belt crosses the face or neck, adjust the shoulder belt anchor height (window-side seating posi- tions only) and then if necessary move the child closer to the belt buckle to help pro- vide a good shoulder belt fit. Care must be taken to securely place the lap belt as low as possible on the hips and not on the child’s waist. If the shoulder portion of the belt cannot be properly positioned, a child restraint system should be used. Never place the shoulder belt under the child’s arm or behind the child’s back.


(cid:84) Expectant mothers


100100


Expectant mothers also need to use the seatbelts. They should consult their doctor for specific recommendations. The lap belt should be worn securely and as low as possible over the hips, not over the waist.


(cid:132) Emergency Locking Retrac-


tor (ELR)


The driver’s seatbelt has an Emergency Locking Retractor (ELR). The emergency locking retractor allows normal body movement but the retractor locks automatically during a sudden stop, impact or if you pull the belt very quickly out of the retractor.


Seat, seatbelt and SRS airbags 1-17


(cid:132) Automatic/Emergency Lock-


ing Retractor (A/ELR)


Each passenger’s seatbelt has an Auto- matic/Emergency Locking Retractor (A/ ELR). The Automatic/Emergency Locking Retractor normally functions as an Emer- gency Locking Retractor (ELR). The A/ ELR has an additional locking mode “Au- tomatic Locking Retractor (ALR) mode” in- tended to secure a child restraint system. When the seatbelt is once drawn out com- pletely and is then retracted even slightly, the retractor locks the seatbelt in that po- sition and the seatbelt cannot be extend- ed. As the belt is rewinding, clicks will be heard which indicate the retractor func- tions as ALR. When the seatbelt is retract- ed fully, ALR mode is released.


When securing a child restraint system on the passengers’ seats, the seatbelt must be changed over to the Automatic Locking Retractor (ALR) mode. When the child restraint system is re- moved, make sure that the retractor is re- stored to the Emergency Locking Retrac- tor (ELR) function by allowing the seatbelt to retract fully. For instructions on how to convert the re- tractor to the ALR mode and restore it to the ELR mode, see the “Child restraint systems” section in this chapter.


– CONTINUED –


A3120BE-B.book 18 ページ 2006年5月30日 火曜日 午前9時32分


1-18 Seat, seatbelt and SRS airbags


(cid:132) Seatbelt warning light


and chime


Your vehicle is equipped with a seatbelt warning device at the driver’s and front passenger’s seat. With the ignition switch turned to the “ON” position, this device reminds the driver and front passenger to fasten their seat- belts by illuminating the warning lights in the locations indicated in the following il- lustrations and sounding a chime.


Driver’s warning light


100372


PASS


100373


Front passenger’s warning light


(cid:84) Operation If the driver and/or front passenger have/ has not yet fastened the seatbelt(s) when the ignition switch is turned to the “ON” po- sition, the seatbelt warning light(s) will flash for 6 seconds, to warn that the seat- belt(s) is/are unfastened. If the driver’s seatbelt is not fastened, a chime will also sound simultaneously. If the driver’s and/or front passenger’s seatbelt(s) are/is still not fastened 6 sec- onds later, both warning lights or the warning light for the unfastened seatbelt will remain lit for 15 seconds. If the driver’s and/or front passenger’s seatbelt(s) are/is still not fastened even 15 seconds later (21 seconds after turning ON the ignition


switch), the warning lights will alternate between flashing and steady illumination at 15-second intervals, and the chime will sound while the warning light(s) is/are flashing. Alternate flashing and steady illumination of the warning lights and sounding of the chime will continue until both driver and front passenger fasten their seatbelts. NOTE (cid:121) If the driver and/or front passenger unfasten(s) the seatbelt(s) after fasten- ing, the seatbelt warning device oper- ates as follows according to the vehi- cle speed.


(cid:121) At speeds lower than approximate- ly 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals. The chime will not sound. (cid:121) At speeds higher than approxi- mately 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals and the chime will sound while the warning light(s) is/are flashing.


(cid:121) It is possible to cancel the warning operation that follows the 6-second


1


A3120BE-B.book 19 ページ 2006年5月30日 火曜日 午前9時32分


warning after turning ON the ignition switch. When the ignition switch is turned ON next time, however, the complete sequence of the warning op- eration resumes. For further details about canceling the warning operation, please contact your SUBARU dealer.


If there is no passenger on the front pas- senger’s seat, the seatbelt warning device for the front passenger’s seat will be deac- tivated. The front passenger’s occupant detection system monitors whether or not there is a passenger on the front passen- ger’s seat. Observe the following precautions. Failure to do so may prevent the device from func- tioning correctly or cause the device to fail. (cid:121) Do not install any accessory such as a table or TV onto the seatback. (cid:121) Do not store a heavy load in the seat- back pocket. (cid:121) Do not allow the rear seat/second-row seat occupant to place his/her hands or legs on the front passenger’s seatback, or allow him/her to pull the seatback.


If the seatbelt warning device for the front passenger’s seat does not function cor- rectly (e.g., it is activated even when the front passenger’s seat is empty or it is de- activated even when the front passenger


has not fastened his/her seatbelt), take the following actions. (cid:121) Ensure that no article is placed on the seat other than a child restraint system and the child occupant. (cid:121) Ensure that there is no article left in the seatback pocket.


If the seatbelt warning device for front passenger’s seat still does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an in- spection.


(cid:132) Fastening the seatbelt


(cid:121) Never use a belt that is twisted or reversed. In an accident, this can increase the risk or severity of in- jury.


(cid:121) Keep the lap belt as low as possi- ble on your hips. In a collision, this spreads the force of the lap belt over stronger hip bones in- stead of across the weaker abdo- men.


Seat, seatbelt and SRS airbags 1-19


(cid:121) Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. To reduce the risk of sliding under the seatbelt in a collision, the front seatbacks should be always used in the upright position while the vehicle is running. If the front seatbacks are not used in the up- right position in a collision, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death.


(cid:121) Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will in- crease, and both can result in se- rious internal injury or death.


– CONTINUED –


A3120BE-B.book 20 ページ 2006年5月30日 火曜日 午前9時32分


1-20 Seat, seatbelt and SRS airbags


from the steering wheel as practical while still maintaining full vehicle control. Front passenger’s seat: Adjust the seat- back to the upright position. Move the seat as far back as possible. 2. Sit well back in the seat. 3. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again.


100101


Never place the shoulder belt under the arm or behind the back. If an ac- cident occurs, this can increase the risk or severity of injury.


Metallic parts of the seatbelt can be- come very hot in a vehicle that has been closed up in sunny weather; they could burn an occupant. Do not touch such hot parts until they cool.


(cid:84) Front seatbelts 1. Adjust the seat position: Driver’s seat: Adjust the seatback to the upright position. Move the seatback as far


4. Insert the tongue plate into the buckle until you hear a click.


100102


100103


5. To make the lap part tight, pull up on the shoulder belt. 6. Place the lap belt as low as possible on your hips, not on your waist.


A3120BE-B.book 21 ページ 2006年5月30日 火曜日 午前9時32分


(cid:86) Adjusting the front seat shoulder


belt anchor height


100374


The shoulder belt anchor height should be adjusted to the position best suited for the driver/front passenger. To lower the an- chor height, push the release button and slide the anchor down. To raise the an- chor height, slide the anchor up. Pull down on the anchor to make sure that it is locked in place. Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck.


When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision.


(cid:86) Unfastening the seatbelt


Seat, seatbelt and SRS airbags 1-21


(cid:84) Rear seatbelts (5-seater models)/


Second-row seatbelts (7-seater models) – excluding center seatbelt


1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving a strong pull on it, then pull it out slowly again.


100105


100102


Push the button on the buckle.


Before closing the door, make sure that the belts are retracted properly to avoid catching the belt webbing in the door.


3. Insert the tongue plate into the buckle until you hear a click.


– CONTINUED –


A3120BE-B.book 22 ページ 2006年5月30日 火曜日 午前9時32分


1-22 Seat, seatbelt and SRS airbags


(cid:86) Adjusting the shoulder belt anchor height (rear seats of 5-seater mod- els/second-row seats of 7-seater models)


100103


4. To make the lap part tight, pull up on the shoulder belt. 5. Place the lap belt as low as possible on your hips, not on your waist.


When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision.


(cid:86) Unfastening the seatbelt


100375


The shoulder belt anchor height should be adjusted to the position best suited for you. To lower the anchor height, push the release button and slide the anchor down. To raise the anchor height, slide the an- chor up. Pull down on the anchor to make sure that it is locked in place. Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck.


100105


Push the button on the buckle.


Before closing the door, make sure that the belts are retracted properly to avoid catching the belt webbing in the door.


Seat, seatbelt and SRS airbags 1-23


(cid:84) Rear center seatbelt (5-seater mod- els)/second-row center seatbelt (7- seater models)


A3120BE-B.book 23 ページ 2006年5月30日 火曜日 午前9時32分


NOTE


1) Holder


100362


100376


With the seatback folded, attach the tongue plate of each rear/second-row seatbelt to the corresponding holder. Do the same also before someone gets into the third-row seat.


1) Center seatbelt tongue plate 2) Connector (tongue) 3) Connector (buckle) 4) Center seatbelt buckle


100108


Fastening the seatbelt with the web- bing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, espe- cially when inserting the connec- tor’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twist- ed.


– CONTINUED –


A3120BE-B.book 24 ページ 2006年5月30日 火曜日 午前9時32分


1-24 Seat, seatbelt and SRS airbags


100377


100378


100379


Center seatbelt is stowed in the recess of the ceiling.


2. Pull out the seatbelt slowly from the overhead retractor.


Be sure to fasten both tongue plates to the respective buckles. If the seatbelt is used only as a shoulder belt (with the connector’s tongue plate not fastened to the connec- tor’s buckle on the right-hand side), it cannot properly restrain the wear- er in position in an accident, possi- bly resulting in serious injury or death.


1. Remove the connector (tongue) plate from the slot located at the front of the re- cess by pulling the connector (tongue) plate rearward.


100678


3. After confirming that the webbing is not twisted, insert the connector (tongue) at- tached at the webbing end into the buckle on the right-hand side until a click is heard.


A3120BE-B.book 25 ページ 2006年5月30日 火曜日 午前9時32分


” mark on the ” mark


Make sure that the “ connector (tongue) and the “ on the buckle are aligned. If the belt stops before reaching the buck- le, return the belt slightly and pull it out more slowly. If the belt still cannot be un- locked, let the belt retract slightly after giv- ing it a strong pull, then pull it out slowly again.


100114


4. Insert the center seatbelt tongue plate in the center seatbelt buckle marked “CENTER” on the left-hand side until it clicks.


100310


5. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist. (cid:86) Unfastening the seatbelt


Seat, seatbelt and SRS airbags 1-25


Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt.


100381


100382


100116


1. Insert a key or other hard pointed ob- ject into the slot in the connector (buckle) on the right-hand side and push it in, and – CONTINUED –


A3120BE-B.book 26 ページ 2006年5月30日 火曜日 午前9時32分


1-26 Seat, seatbelt and SRS airbags


the connector (tongue) plate will discon- nect from the buckle.


200300


2. With the belt held by hand, allow the re- tractor to roll up the belt slowly. You should hold the webbing end and guide it back into the retractor while it is rolling up. Neatly store the tongue plate in the recess on the ceiling and then insert the connec- tor (tongue) plate into the slot located at the front of the recess.


100383


(cid:121) Do not allow the retractor to roll up the seatbelt too quickly. Other- wise, the metal tongue plates may hit against the trim, resulting in damaged trim.


(cid:121) Have the seatbelt fully rolled up so that the tongue plates are neat- ly stored. A hanging tongue plate can swing and hit against the trim during driving, causing damage to the trim.


(cid:84) Third-row seatbelt (7-seater models) 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If


the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving a strong pull on it, then pull it out slowly again.


3. Insert the tongue plate into the buckle until you hear a click.


100102


A3120BE-B.book 27 ページ 2006年5月30日 火曜日 午前9時32分


100103


4. To make the lap part tight, pull up on the shoulder belt. 5. Place the lap belt as low as possible on your hips, not on your waist. (cid:86) Unfastening the seatbelt


Seat, seatbelt and SRS airbags 1-27


the belts because this could seriously af- fect their strength.


Inspect the seatbelts and attachments in- cluding the webbing and all hardware pe- riodically for cracks, cuts, gashes, tears, damage, loose bolts or worn areas. Re- place the seatbelts even if only minor damage is found.


(cid:121) Keep the belts free of polishes, oils, chemicals and particularly battery acid.


(cid:121) Never attempt to make modifica- tions or changes that will prevent the seatbelt from operating prop- erly.


Push the button on the buckle. NOTE


100647


1) Holder


(cid:121) Before folding or raising the seat- back of the third-row seat, confirm that the seatbelt is flat against the sidewall at the lower point and the webbing is attached to the holder. (cid:121) When raising the seatback of the third-row seat, if the seatbelt catches on the seatback, hold the belt forward of the seatback while latching the seat- back.


(cid:132) Seatbelt maintenance To clean the seatbelts, use a mild soap and lukewarm water. Never bleach or dye


100105


A3120BE-B.book 28 ページ 2006年5月30日 火曜日 午前9時32分


1-28 Seat, seatbelt and SRS airbags


Front seatbelt pretensioners


seat occupant.


When a seatbelt pretensioner is activated, an operating noise will be heard and a small amount of smoke will be released. These occurrences are normal and not harmful. This smoke does not indicate a fire in the vehicle.


Once the seatbelt pretensioner has been activated, the seatbelt retractor remains locked. Consequently, the seatbelt can not be pulled out and retracted and there- fore must be replaced. NOTE (cid:121) Seatbelt pretensioners are not de- signed to activate in minor frontal im- pacts, in minor side impacts or rear im- pacts. (cid:121) The seatbelt pretensioners for the driver’s seat and front passenger’s seat operate at the same time as the frontal, and side SRS airbags. If the ve- hicle rolls over, they operate simulta- neously with the curtain airbag. (cid:121) Pretensioners are designed to func- tion on a one-time-only basis. In the event that a pretensioner is activated, both the driver’s and front passenger’s seatbelt retractor assemblies must be replaced and only by an authorized SUBARU dealer. When replacing seat-


100121


The driver’s and front passenger’s seat- belts have a seatbelt pretensioner. The seatbelt pretensioners for the driver’s seat and front passenger’s seat operate at the same time as the frontal, and side SRS airbags. If the vehicle rolls over, they oper- ate simultaneously with the curtain airbag.


The front and side airbag sensors and the rollover sensor are used as the preten- sioner sensors. If a sensor detects a cer- tain predetermined amount of force during a frontal collision, a side impact collision or a rollover collision of the vehicle, the front seatbelt is quickly drawn back in by the retractor to take up the slack so that the belt more effectively restrains the front


belt retractor assemblies, use only genuine SUBARU parts.

Loading...
x