Download PDF Manual

1-69


Seat, seatbelt and SRS airbags


(cid:86) When will the SRS side airbag most likely de-


ploy?


A severe side impact near the front seat activates the SRS side airbag.


UG1519BA


1-70


(cid:86) When is the SRS side airbag unlikely to deploy?


Seat, seatbelt and SRS airbags


1) The vehicle is involved in an ob-


lique side-on impact.


2) The vehicle is involved in a side-on impact in an area outside the vicin- ity of the passenger compartment.


3) The vehicle strikes a telephone


pole or similar object.


4) The vehicle is involved in a side-on


impact from a motorcycle.


5) The vehicle rolls onto its side or


roof.


UG1085BB


– CONTINUED – 1-71


Seat, seatbelt and SRS airbags


There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of accidents like those illustrated, the SRS side airbag may not deploy depending on the level of accident forces involved.


1-72


(cid:86) When will the SRS side airbag not deploy?


1) The vehicle is involved in a frontal collision with anoth-


er vehicle (moving or stationary). 2) The vehicle is struck from behind.


HG1051BB


The SRS side airbag is basically not designed to de- ploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are il- lustrated.


vated on the second.


(cid:132) SRS airbag system monitors


Seat, seatbelt and SRS airbags


HS1102BB


UG7020DA


1) First impact 2) Second impact In an accident where the vehicle is struck from the side more than once, the SRS side airbag deploys only once. Example: In the case of a double side impact collision, first with one vehicle and immediately followed by an- other from the same direction, once the SRS side air- bag is activated on the first impact, it will not be acti-


A diagnostic system continually monitors the readi- ness of the SRS airbag system while the vehicle is be- ing driven. The SRS airbag system warning light “AIR- BAG” will show normal system operation by lighting for about 6 seconds when the ignition key is turned to the “ON” position. The following components are monitored by the indi- cator: (cid:121) Front sub sensor (Right hand side) (cid:121) Front sub sensor (Left hand side)


– CONTINUED – 1-73


Seat, seatbelt and SRS airbags


(cid:121) Airbag control module (including impact sensors) (cid:121) Frontal airbag module (Driver’s side) (cid:121) Frontal airbag module (Passenger’s side) (cid:121) Side airbag sensor (Driver’s side – if equipped) (cid:121) Side airbag sensor (Passenger’s side – if equipped) (cid:121) Side airbag module (Driver’s side – if equipped) (cid:121) Side airbag module (Passenger’s side – equipped) (cid:121) Seatbelt pretensioner (Driver’s side) (cid:121) Seatbelt pretensioner (Passenger’s side) (cid:121) All related wiring


if


If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly re- paired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of inju- ry. (cid:121) Flashing or flickering of the indicator light (cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” posi- tion


1-74


(cid:121) Continuous illumination of the warning light (cid:121) Illumination of the warning light while driving


(cid:132) SRS airbag system servicing


(cid:121) When discarding an airbag module or scrap- ping the entire vehicle damaged by a collision, consult your SUBARU dealer. (cid:121) The SRS airbag has no user-serviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your nearest SUBARU dealer. Tampering with or disconnecting the system’s wiring could re- sult in accidental inflation of the SRS airbag or could make the system inoperative, which may result in serious injury. The wiring harnesses of the SRS airbag system are covered with yellow insulation and system connectors are yellow for easy identification.


If you need service or repair in areas listed be- low, we recommend that you have an autho- rized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas. (cid:121) Under the center console (cid:121) Inside each front fender (cid:121) Steering wheel and column and nearby areas (cid:121) Top of the dashboard on front passenger’s side and nearby areas (cid:121) Each front seat and nearby area (only for ve- hicles with SRS side airbags) (cid:121) Inside each center pillar


In the event that the SRS airbag is deployed, re- placement of the system should be performed only by an authorized SUBARU dealer. When the components of the SRS airbag system are re- placed, use only genuine SUBARU parts. To ensure their long-term reliability, the SRS airbags must be inspected by a SUBARU dealer ten years af- ter the date of manufacture, which is shown on the cer- tification plate attached to the driver’s door jamb.


Seat, seatbelt and SRS airbags


NOTE In the following cases, contact your SUBARU deal- er as soon as possible. (cid:121) The front part of the vehicle was involved in an accident in which the SRS frontal airbags did not deploy. (cid:121) The pad section of the steering wheel or front passenger’s frontal airbag cover is scratched, cracked, or otherwise damaged. In addition, if your vehicle is equipped with SRS side airbags, contact your SUBARU dealer as soon as possible in the following cases. (cid:121) Either center pillar or a nearby area of the vehi- cle was involved in an accident in which the SRS side airbag did not deploy. (cid:121) The fabric or leather of either front seatback is cut, frayed, or otherwise damaged.


(cid:132) Precautions against vehicle modifica-


tion


in serious


(cid:121) To avoid accidental activation of the system or rendering the system inoperative, which may result injury, no modifications – CONTINUED – 1-75


winches, snow plow, skid plate, etc.) other than genuine SUBARU accessory parts to the front end. (cid:121) Modification of the suspension system or front end structure. (cid:121) Installation of a tire of different size and con- struction from the tires specified on the tire placard attached to the driver’s door jamb. (cid:121) Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body (for vehicles with side airbags only).


Always consult your SUBARU dealer if you want to in- stall any accessory parts to your vehicle.


Seat, seatbelt and SRS airbags


should be made to any components or wiring of the SRS airbag system. This includes following modifications:


(cid:121) Installation of custom steering wheels (cid:121) Attachment of additional trim materials to the dashboard (cid:121) Installation of custom seats (for vehicles with SRS side airbags only) (cid:121) Replacement of seat fabric or leather (for vehicles with SRS side airbags only) (cid:121) Installation of additional fabric or leather on the front seat (for vehicles with SRS side airbags only)


(cid:121) Installation of additional electrical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could inter- fere with proper operation of the SRS airbag system.


Do not perform any of the following modifica- tions. Such modifications can interfere with proper operation of the SRS airbag system. (cid:121) Attachment of any equipment (brush bar,


1-76


Keys ............................................................... Key number ....................................................... Immobilizer (WRX-STi) ................................. Security ID plate ................................................ Security indicator light ..................................... Key replacement ............................................... Door locks ..................................................... Locking and unlocking from the outside ........ Locking and unlocking from the inside .......... Power door locking switches ...................... Remote keyless entry system ..................... Locking the doors ............................................. Unlocking the doors ......................................... Illuminated entry ............................................... Vehicle finder function ..................................... Sounding a panic alarm ................................... Selecting audible signal operation .................. Replacing the battery ....................................... Replacing lost transmitters .............................. Security system (if equipped) ..................... System operation .............................................. Arming the system ............................................ Disarming the system ....................................... Valet mode ......................................................... Passive arming .................................................. Child safety locks ......................................... Windows ........................................................ Power windows ................................................. Trunk lid (Sedan) ..........................................


2-2
2-3
2-3
2-4
2-5
2-5
2-6
2-6
2-7
2-8
2-9
2-10
2-10
2-11
2-11
2-11
2-11
2-11
2-13
2-17
2-17
2-17
2-19
2-20
2-20
2-23
2-24
2-24
2-27


Keys and doors


To open and close the trunk lid from outside ............................................................ To open the trunk lid from inside .................... To cancel the trunk lid release ........................ Internal trunk lid release handle ......................


2-27
2-28
2-28
2-28
Rear gate (Wagon) ........................................ 2-31
Moonroof (if equipped) ................................. 2-33
2-33
2-33
2-35


Tilt function ....................................................... Sliding function ................................................. Sun shades ........................................................


2-1


Keys and doors


Keys and doorsKeys


WRX-STi 1) Master key (Black) 2) Submaster key (Black) 3) Valet key (Gray) 4) Key number plate 5) Security ID plate


2-2


UG2044BC


HS2011BB


Except WRX-STi 1) Master key 2) Submaster key 3) Valet key 4) Key number plate Three types of keys are provided for your vehicle: Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle. (cid:121) Ignition switch (cid:121) Doors (cid:121) Trunk (Sedan) (cid:121) Glove box


The valet key fits only the ignition switch and driver’s door lock. You can keep the trunk and glove box locked when you leave your vehicle and valet key at a parking facility.


Do not attach a large key holder or key case to either key. If it banged against your knees while you were driving, it could turn the ignition switch from the ON position to the ACC or OFF position, thereby stopping the engine.


(cid:132) Key number The key number is stamped on the metal plate at- tached to the key set. Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.


Keys and doors


Immobilizer (WRX-STi) The immobilizer system is designed to prevent an un- authorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregis- tered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds. Each immobilizer key contains a transponder in which the key’s ID code is stored. When a key is inserted into the ignition switch and turned to the “ON” position, the transponder transmits the key’s ID code to the immo- bilizer system’s receiver. If the transmitted ID code matches the ID code registered in the immobilizer sys- tem, the system allows the engine to be started. Since the ID code is transmitted and acted upon almost in- stantly, the immobilizer system does not impede nor- mal starting of the engine. If the engine fails to start, pull out the key once before trying again. (Refer to the “Ignition switch” section [chapter 3].) NOTE To protect your vehicle from theft, please pay close attention to the following security precau- tions:


– CONTINUED – 2-3


Keys and doors


(cid:121) Never leave your vehicle unattended with its keys inside. (cid:121) Before leaving your vehicle, close all windows and lock the doors and rear gate. (cid:121) Do not leave spare keys or any record of your key number in the vehicle.


(cid:121) Do not place the key under direct sunlight or anywhere it may become hot. (cid:121) Do not get the key wet. If the key gets wet, wipe it dry with a cloth immediately.


(cid:132) Security ID plate


UB2534BB


A) Key number plate B) Security ID plate The security ID is stamped on the metal plate attached to the key set. Write down the security ID and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle. This number is also needed for replacement or repair of the engine control unit, immobilizer control unit.


2-4


(cid:132) Security indicator light The security indicator light deters potential thieves by indicating that the vehicle is equipped with an immobi- lizer system. It begins flashing (approximately once every three seconds) about 60 seconds after the igni- tion switch is turned from the “ON” position to the “ACC” or “LOCK” position or immediately after the key is pulled out. If the security indicator light does not flash, the immo- bilizer system may be faulty. If this occurs, we recom- mend that you contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light comes on. NOTE Even if the security indicator light flashes irregu- larly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will func- tion normally.


(cid:132) Key replacement Your key number and security ID will be required if you ever need a replacement key made. Any new key must be registered for use with your vehicle’s immobi- lizer system before it can be used. Up to four keys can


Keys and doors


be registered for use with one vehicle. For security, all the keys registered with your vehicle’s immobilizer system will have their ID codes erased and re-registered when a new key is made. Therefore, all of your vehicle’s keys must be presented when a new key is registered. Any key that is not re-registered when a new key is made cannot be used after the oth- er keys are re-registered. For information on replace- ment keys and on the registration of keys with your im- mobilizer system, we recommend that you contact your SUBARU dealer. NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation. NO USER SERVICEABLE PARTS INSIDE. DO NOT ATTEMPT TO MODIFIED THIS EQUIP- MENT. IF MODIFIED, YOUR AUTHORITY TO OP- ERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC or Industry Canada.


– CONTINUED – 2-5


Keys and doors


Door locks (cid:132) Locking and unlocking from the out-


side


UG2501BA


To lock the door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front. Pull the outside door handle to open an unlocked door.


2-6


HS2013EB


1) Rotate the lock lever rearward. 2) Close the door. To lock the door from the outside without the key, ro- tate the lock lever rearward and then close the door. To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK” side) and then close the door. In this case, all closed doors and the rear gate (for Wagon) are locked at the same time. Always make sure that all doors and the rear gate (for Wagon) are locked before leaving your vehicle.


NOTE Make sure that you do not leave the key inside the vehicle when locking the doors from the outside without the key.


(cid:132) Locking and unlocking from the inside


is unlocked. Pull the inside door handle to open an unlocked door. Always make sure that all doors and the rear gate (for Wagon) are closed before starting to drive.


Keys and doors


UG2502BB


1) Lock 2) Unlock To lock the door from the inside, rotate the lock lever rearward. To unlock the door from the inside, rotate the lock lever forward. The red mark on the lock lever appears when the door


Keep all doors locked when you drive, especial- ly when small children are in your vehicle. Along with the proper use of seatbelts and child restraints, locking the doors reduces the chance of being thrown out of the vehicle in an accident. It also helps prevent passengers from falling out if a door is accidentally opened, and intrud- ers from unexpectedly opening doors and en- tering your vehicle.


– CONTINUED – 2-7


Keys and doors


Power door locking switches


NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using power door locking switches.


HS2015BB


1) Lock 2) Unlock All doors and the rear gate (for Wagon) can be locked and unlocked by the power door locking switches lo- cated at the driver’s side and the front passenger’s side doors. To lock the doors, push the front side of the switch. To unlock the doors, push the rear side of the switch. When you close the doors after you set the door locks, the doors remain locked.


2-8


Remote keyless entry system Two transmitters are provided for your vehicle. The remote keyless entry system has the following functions. (cid:121) Locking and unlocking the doors (and rear gate on the Wagon) without a key (cid:121) Sounding a panic alarm (cid:121) Arming and disarming the security system (if your vehicle is equipped with an optional security system). See the next section “Security system (if equipped)” for detailed information. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The operable distance of the keyless entry system is approximately 30 feet (10 meters). However, this dis- tance will vary depending on environmental condi-


Keys and doors


tions. The system’s operable distance will be shorter in areas near a facility or electronic equipment emitting strong radio waves such as a power plant, broadcast station, TV tower, or remote controller of home elec- tronic appliances. The remote keyless entry system does not operate when the key is inserted in the ignition switch to pre- vent accidental lockout.


(cid:121) Do not expose the transmitter to severe shocks, such as those experienced as a result of dropping or throwing. (cid:121) Do not take the transmitter apart except when replacing the battery. (cid:121) Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.


– CONTINUED – 2-9


Keys and doors


UG2042BA


: LOCK/ARM button


Press to Lock all doors. Press and Hold to activate panic alarm. Press three times in a five-second period to use vehi- cle finder function. :UNLOCK/DISARM button 1) Press once to Unlock driver’s door. 2) Press a second time to Unlock all other doors (and


rear gate on the Wagon).


(cid:132) Locking the doors Briefly press the “ ” button (for less than two sec- onds) to lock all doors (and rear gate on the Wagon). An electronic chirp will sound once and the turn signal


2-10


lights will flash once. If any of the doors (or the rear gate) is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, it will automatically lock. NOTE ” button is pressed for two seconds or If the “ longer, the panic alarm will sound. When locking the doors in normal circumstances, press the “ ” button for less than two seconds. For de- tails on the panic alarm, refer to “Sounding a panic alarm”.


(cid:132) Unlocking the doors Briefly press the “ ” button (for less than two sec- onds) to unlock the driver’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all other doors (and rear gate on the Wagon), briefly press the “ ” button a second time within 5 seconds. NOTE If the interval between the first and second press- es of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the


system may not respond.


(cid:132) Illuminated entry The interior (dome) light and ignition switch light (for turbo models) will illuminate when the “ ” button is pressed. These lights stay illuminated for approxi- mately 30 seconds if any of the doors (or the rear gate on the Wagon) is not opened. If the “ ” button is pressed before 30 seconds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light switch must be set to the middle position in order for this function to operate.


(cid:132) Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “ ” button three times in a five-second period will cause your vehicle’s horn to sound once and its turn signal lights to flash three times.


(cid:132) Sounding a panic alarm To activate the alarm, keep the “ for more than two seconds.


” button pressed


Keys and doors


The horn will sound and the turn signal lights will flash. To deactivate it, press the “ ” but- ton. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30 sec- onds.


” button or “


” and “


(cid:132) Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If de- sired, you may turn the audible signal off. To turn the audible signal off, unlock the door by ” button and then simultaneously pressing the “ depress “ ” buttons for more than two seconds. An electronic chirp will sound twice and the turn signal lights will flash twice to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the door by pressing the “ ” button and then simultaneously depress “ ” buttons for more than two seconds. An electronic chirp will sound once and the turn signal lights will flash once to inform you that the audible signal has been turned on.


” and “


(cid:132) Replacing the battery When the transmitter battery begins to get weak, transmitter range will begin to decrease. Replace the – CONTINUED – 2-11


Keys and doors


battery as soon as possible. To replace the battery:


UG2043BA


2. Remove the old battery from the holder.


UB2209BA


1. Open the transmitter case using a flat-head screw- driver.


2-12


Keys and doors


(cid:121) Do not let dust, oil or water get on or in the transmitter when replacing the battery. (cid:121) Be careful not to damage the printed circuit board in the transmitter when replacing the bat- tery.


UB2210BB


A) Negative (–) side facing up 3. Replace with a new battery (Type CR2025 or equivalent) making sure to install the new battery with the negative (–) side facing up. 4. Reinstall the back half of the transmitter case by snapping it back on. After the battery is replaced, the transmitter must be synchronized with the keyless entry system’s control unit. Press either the “ ” but- ton six times to synchronize the unit.


” or “


(cid:132) Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system. (cid:84) Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmit- ter codes. The four transmitter codes may be the same or different.


– CONTINUED – 2-13


Keys and doors


To enter the programming mode:


1. Press “ ” button to disarm the security system. (If your vehicle is equipped with the optional security system.)


UG2042CA


2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.


HS2019BD


2-14


Keys and doors


To program the transmitters:


1. Open the driver’s door. 2. Close the driver’s door.


HS2019BE


HS2020BB


1) ON 2) LOCK 4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15
seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode. NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this proce- dures.


– CONTINUED – 2-15


Keys and doors


UG2042BA


3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound twice to indicate that the transmitter has been programmed. Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter. To exit the programming mode: 1. After all of your transmitters are programmed, re- move the key from the ignition switch. The horn will sound three times to indicate that the system has exited the programming mode. 2. Make sure that the keyless entry system properly


2-16


operates by operating each transmitter. (cid:84) Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code re- mains in the memory. For security reasons, lost trans- mitter codes should be deleted from the memory. To delete old transmitter codes, program four trans- mitter codes into the system. If you have only one cur- rent transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memo- ry. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access to your vehicle.


Security system (if equipped) The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key. The system can be armed and disarmed with the re- mote transmitter. The system does not operate when the key is inserted into the ignition switch.


(cid:132) System operation The security system will give the following alarm indi- cations when triggered: (cid:121) The turn signal lights will flash and the horn will sound intermittently. In addition, the starter motor will not operate. (cid:121) The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tam- pered with again. The alarm will continue for six times if any sensor continues to be activated. The alarm is triggered by: (cid:121) Opening a door, the rear gate or trunk lid. (cid:121) Application of physical shock to the vehicle (e.g.


Keys and doors


forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher levels of shock are detected and the system will go into full alarm. (cid:121) Ignition switch being turned on while in armed state. NOTE With the valet mode selected, the security system does not operate when the remote transmitter is used for locking and unlocking. The security indi- cator light in the combination meter flashes twice per second to show that the valet mode is select- ed. For details, refer to “Valet mode” in this sec- tion.


(cid:132) Arming the system (cid:84) To arm the system using remote transmitter 1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood (and the trunk lid) are locked. 5. Close all doors (and the rear gate on the Wagon).


– CONTINUED – 2-17


Keys and doors


1) Press to Arm the system. 2) Press to Disarm the system.


2-18


UG2042BB


UG2030BA


Security indicator light 6. Briefly press the “ ” button (for less than two sec- onds). All doors (and the rear gate on the Wagon) will lock, an electronic chirp will sound once, the turn sig- nal lights will flash once, and the security indicator light will flash as follows: All models except WRX-STi: once every approximate- ly two seconds WRX-STi: twice every approximately two seconds If any of the doors (or the rear gate or the trunk lid) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors (or the rear gate or the trunk lid) are not


properly closed. When you close the door, the system will automatically arm and doors will automatically lock. (cid:84) To arm the system using power door locking


switches


1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood (and the trunk lid) are locked. 5. Close the doors (and the rear gate on the Wagon) but leave only the driver’s door or the front passen- ger’s door open.


UG2038BB


Keys and doors


6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the security in- dicator light will flash as follows: All models except WRX-STi: once every approximate- ly two seconds WRX-STi: twice every approximately two seconds NOTE The system can be armed even if the engine hood and/or the windows are opened. Always make sure that they are fully closed before arming the system.


(cid:132) Disarming the system Briefly press the “ ” button (for less than two sec- onds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound twice, the turn signal lights will flash twice and the security indicator light will go off. NOTE (WRX-STi) If your vehicle is equipped with an immobilizer, the immobilizer’s function will cause the security indi- cator light to flash (once every approximately three seconds) even after the system is disarmed.


– CONTINUED – 2-19


Keys and doors


Refer to “Immobilizer (WRX-STi)” in this chapter for further details. To unlock all other doors (and the rear gate on the Wagon), briefly press the “ ” button a second time. (cid:84) Emergency disarming If you cannot disarm the system using the transmitter (i.e. the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system with- out using the transmitter. To disarm the system: 1. Unlock the door with the key and then open the door. 2. The alarm will sound. 3. Insert the key into the ignition switch and cycle it from the “LOCK” to the “ON” position three (3) times within 5 seconds.


(cid:132) Valet mode When you choose the valet mode, the security system does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors (and rear gate on the Wagon) and panic activation. To enter the valet mode, open the driver’s door and


2-20


” button depressed for more than two keep the “ seconds. The security indicator light will continue to flash twice per second indicating that the system is in the valet mode. To exit valet mode, open the driver’s door and keep ” button pressed for more than two sec- the “ onds. The indicator will stop flashing. NOTE If the remote transmitter is used to lock or unlock the doors while the valet mode is selected, the turn signal lights do not flash but an electronic chirp is emitted.


(cid:132) Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically ac- complished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. (cid:84) To enter the passive mode Since programming the passive arming mode is a complicated procedure, have it done by your nearest SUBARU dealer.


(cid:84) Arming the system 1. Turn the ignition switch to the “ON” position.


HS2024BC


1) ON 2) LOCK 2. Turn the ignition switch from “ON” to “LOCK” posi- tion and remove the key from the ignition switch.


Keys and doors


HS2013FB


3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the in- side door lock levers. 5. Close the doors. The system will automatically arm after one minute. In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arming will take place immediately regardless of whether or not the passive mode has been selected.


– CONTINUED – 2-21


The indicator light provides the following indications. Flashing once: Any door, the rear gate or the trunk lid has been opened. Flashing three times: The impact sensor in the sys- tem’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected. NOTE The battery must be reconnected before the indi- cator light will flash. To exit this mode, close the door and turn the ignition switch to the “ON” position.


Keys and doors


In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4
above or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.


(cid:84) Disarming the system To disarm the system, briefly press the “ on the transmitter. (cid:86) Tripped sensor identification (all models ex-


” button


cept WRX-STi)


If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the sys- tem, this indicates that the alarm was triggered. The number of times the indicator light flashes indicates what sensor caused the alarm condition. To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to the “ON” position twice. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.


2-22


Child safety locks


UG2503BB


1) Lock 2) Unlock Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.


Keys and doors


Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.


– CONTINUED – 2-23


Keys and doors


Windows (cid:132) Power windows


To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window. (cid:121) Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.


The power windows operate only when the ignition switch is in the “ON” position.


2-24


(cid:84) Driver’s side switches


UG2045BB


1) Lock switch 2) For driver’s window (with one-touch auto down fea-


ture)


3) For front passenger’s window 4) For rear left window 5) For rear right window All door windows can be controlled by the power win- dow switch cluster at the driver side door.


(cid:86) Operating the driver’s window


HS2027BB


1) Open 2) Automatically open 3) Close To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without hold- ing the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window half- way, pull the switch up lightly.


Keys and doors


To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows


HS2027CA


To open the passengers’ windows, push the appropri- ate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired position.


– CONTINUED – 2-25


Keys and doors


(cid:86) Locking the passengers’ windows


cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.


HS2028BB


1) Lock 2) Unlock To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. (cid:84) Passengers’ side switches To open the window, push the switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch


2-26


Trunk lid (Sedan)


(cid:132) To open and close the trunk lid from


outside


Keys and doors


(cid:121) To prevent dangerous exhaust gas from en- tering the vehicle, always keep the trunk lid closed while driving. (cid:121) Help prevent young children from locking themselves in the trunk. When leaving the vehi- cle, either close all windows and lock all doors or cancel the inside trunk lid release. Also make certain that the trunk is closed. On hot or sunny days, the temperature in the trunk could quickly become high enough to cause death or serious heat-related injuries in- cluding brain damage, particularly for small children.


UG2047BA


To open the trunk lid from outside, insert the key and turn it clockwise. To close the trunk lid, lightly press the trunk lid down until the latch engages.


– CONTINUED – 2-27


Keys and doors


(cid:132) To open the trunk lid from inside


(cid:132) To cancel the trunk lid release


1) Open Pull the trunk lid release lever upward.


2-28


UG2511BB


UG2048BA


The inside trunk lid release can be cancelled to help prevent unauthorized entry into the trunk. To cancel the trunk lid release, set the lid release cancel lever (located on the inside of the trunk lid, mounted to the trunk lid latch) to the “CANCEL” position. When this lock is in the “CANCEL” position, the trunk can be opened only with the key.


(cid:132) Internal trunk lid release handle The internal trunk lid release handle is a device de- signed to open the trunk lid from inside the trunk. In the event children or adults become locked inside the


trunk, the handle allows them to open the lid. The han- dle is located on the inside of the trunk lid.


UG2031BA


To open the trunk lid from inside the trunk, press the yellow handle downward as indicated by the arrow on the handle. This operation unlocks the trunk lid. Then, push up the lid. The handle is made of material that remains lumines- cent for approximately an hour in the dark trunk space after it is exposed to ambient light even for a short time.


Keys and doors


Never allow any child to get in the trunk and play with the release handle. If the driver starts the vehicle without knowing that a child is in- side the trunk and the child opens the lid using the release handle, the child could fall out and be killed or seriously injured.


(cid:121) Do not close the lid while gripping the release handle. The handle may be damaged. (cid:121) Do not use the handle as a hook to fasten straps or ropes to secure your cargo in the trunk. Such use may result in damage of the handle. (cid:121) Load the trunk so that cargo can not strike the release handle. If the cargo hits the handle while the vehicle is being driven, the handle may be pushed down and the trunk lid may open. That may cause cargo to fall out of the trunk, which could create a traffic safety haz- ard.


– CONTINUED – 2-29


Keys and doors


(cid:84) Inspection Perform the following steps at least twice a year to check the release handle for correct operation. 1. Open the trunk lid.


This places the latch in the locked position.


UG2033BA


2. Use a screwdriver with a thin blade. Slide the screwdriver blade from the slit aperture of the lock as- sembly fully to the end until you hear a click.


UG2032BA


2-30


UG2034BA


3. Move the release handle, from outside the vehicle, in the direction of the arrow to check if the latch is re- leased. If the latch is not released, contact your SUBARU dealer. In that case, use the key to release the latch, then close the trunk lid. Also, if the movements of the release handle feel re- stricted or not entirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer.


Keys and doors


Rear gate (Wagon)


UG2049BA


The rear gate can be locked and unlocked using either the keyless entry system or the power door locking switches. Refer to the “Power door locking switches” and “Re- mote keyless entry system” sections in this chapter. To open the rear gate, first unlock the rear gate lock then pull the outside handle up. Then, hold the rear gate and raise it as high as it will go.


– CONTINUED – 2-31


Keys and doors


UG2512BA


To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull down on the recessed grip.


(cid:121) To prevent dangerous exhaust gas from en- tering the vehicle, always keep the rear gate closed while driving. (cid:121) Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger


2-32


of your hand being caught and injured.


Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.


NOTE If the rear gate cannot be unlocked due to a dis- charged battery, a fault in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release le- ver. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” in chapter 9 “In case of emergency”.


Moonroof (if equipped) The moonroof has both tilting and sliding functions. The moonroof operates only when the ignition switch is in the “ON” position.


(cid:132) Tilt function


Keys and doors


Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause damage to the moon- roof.


(cid:132) Sliding function


UG2508BB


1) Tilt up 2) Lower The tilting function will only operate when the moon- roof is fully closed.


1) Open 2) Close


UG2509BB


– CONTINUED – 2-33


To avoid serious personal injury caused by en- trapment, you must do the following: (cid:121) Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.


(cid:121) Do not sit on the edge of the open moonroof. (cid:121) Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.


Keys and doors


Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you con- tinue to press on the switch. Release the switch once and push it again to close the moonroof completely. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to pre- vent water drops from falling into the passenger com- partment. NOTE If the moonroof cannot be closed through switch operation because of system failure, it can be closed manually using a hex-head wrench. For the procedure, refer to “Moonroof – if the moonroof cannot be closed” in Chapter 9 “In case of emer- gency”.


(cid:121) Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident.


2-34


(cid:132) Sun shades


Keys and doors


UG2510BA


The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.


– CONTINUED – 2-35


Ignition switch .............................................. LOCK .................................................................. ACC .................................................................... ON ....................................................................... START ................................................................ Key reminder chime .......................................... Ignition switch light .......................................... Key interlock release (AT vehicles only) ........ Hazard warning flasher ................................ Meters and gauges (WRX-STi) .................... Combination meter illumination ...................... Cancelling sequential illumination of the combination meter ......................................... Speedometer ..................................................... Odometer/Trip meter ........................................ Tachometer ........................................................ Fuel gauge ......................................................... Temperature gauge ........................................... Outside temperature indicator ......................... (WRX-STi) .................................................. Setting the alarm-level engine speed .............. Deactivating the REV alarm system ................ Meters and gauges (Except WRX-STi) ........ Speedometer ..................................................... Odometer/Trip meter ........................................ Tachometer ........................................................ Fuel gauge ......................................................... Temperature gauge ........................................... Outside temperature indicator (if equipped) .. Warning and indicator lights .......................


REV indicator light and buzzer


3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-6
3-7
3-7
3-7
3-7
3-8
3-8
3-9
3-10
3-11
3-12
3-13
3-13
3-15
3-15
3-15
3-15
3-16
3-17
3-18
3-19
3-20


Instruments and controls


Seatbelt warning light and chime .................... SRS airbag system warning light .................... CHECK ENGINE warning light/ Malfunction indicator lamp ........................... Charge warning light ........................................ Oil pressure warning light ............................... AT OIL TEMPerature warning light (for AT vehicles) ............................................. Rear differential oil temperature warning light (WRX-STi) ........................................................ ABS warning light ............................................. Brake system warning light ............................. Door open warning light .................................. All-wheel drive warning light (for AWD AT vehicles – if equipped) ............ Intercooler water spray warning light (WRX-STi) ........................................................ Selector lever position indicator (AT vehicles) ................................................... Turn signal indicator lights .............................. High beam indicator light.................................. Cruise control indicator light ........................... Cruise control set indicator light .................... Driver’s control center differential auto indicator light (WRX-STi) ............................... Driver’s control center differential indicator lights (WRX-STi) ............................. Headlight indicator light (WRX-STi) ................ REV indicator light (WRX-STi) .........................


3-20
3-20
3-21
3-22
3-22
3-22
3-23
3-23
3-24
3-26
3-26
3-26
3-27
3-27
3-27
3-27
3-27
3-28
3-28
3-28
3-28
Clock .............................................................. 3-29
Light control switch ...................................... 3-30
3-30


Headlights .........................................................


3-1


Instruments and controls


High/low beam change (dimmer) .................... Headlight flasher .............................................. Daytime running light system (except U.S.-spec. WRX-STi) ......................... Turn signal lever ........................................... Illumination brightness control ................... Illumination brightness control (WRX-STi) .................................................. Headlight beam leveler (U.S.-spec. WRX-STi) ................................ Parking light switch ..................................... Fog light button (if equipped) ..................... Wiper and washer ......................................... Windshield wiper and washer switches ......... Rear window wiper and washer switch – Wagon .......................................................... Rear window defogger button ..................... Windshield wiper deicer (if equipped) ........ Intercooler water spray switch (WRX-STi) .................................................. Mirrors ........................................................... Inside mirror ...................................................... Outside mirrors ................................................. Tilt steering wheel ........................................ Horn ...............................................................


3-31
3-31
3-32
3-32
3-33
3-34
3-34
3-35
3-36
3-36
3-38
3-40
3-41
3-43
3-44
3-45
3-45
3-48
3-50
3-51


3-2


Instruments and controls


Ignition switch


(cid:84) Automatic transmission vehicles


Instruments and controls


UG3044BA


The ignition switch has four positions: LOCK, ACC, ON and START.


(cid:132) LOCK The key can only be inserted or removed in this posi- tion. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.


HS3015BA


HS2020CA


– CONTINUED – 3-3


Instruments and controls


The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. (cid:84) Manual transmission vehicles


The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.


HS2020DA


(cid:121) Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed be- cause that will lock the steering wheel, prevent- ing steering control. And when the engine is turned off, it takes a much greater effort than


3-4


usual to steer. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. They could operate the power windows, the sunroof or other controls or even make the vehicle move.


(cid:132) ACC In this position the electrical accessories (radio, ciga- rette lighter, etc.) can be used.


(cid:132) ON This is the normal operating position after the engine is started.


(cid:132) START The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.


Do not turn the ignition switch to the “START” position while the engine is running.


(cid:84) For vehicle with immobilizer If you fail to start your engine with your registered key, once pull out the key (at this time, the security indicator light blinks), and then insert the key in the ignition switch and turn it to the “START” position to start your engine again. NOTE The engine may not start in the following cases:


UG3049BA


Instruments and controls


(cid:121) The key grip is touching another key or a metal- lic key holder.


UG3050BA


(cid:121) The key is near another key that contains an im- mobilizer transponder.


(cid:132) Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ig- nition switch.


(cid:132) Ignition switch light For easy access to the ignition switch in the dark, the – CONTINUED – 3-5


Instruments and controls


ignition switch light comes on when driver’s door is opened. The light remains on for 10 seconds and goes out after driver’s door is closed or if the key is turned to the “ON” position.


(cid:132) Key interlock release (AT vehicles


only)


If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.


UG3025BA


3. Turn the ignition key while pressing the key inter- lock release lever. Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired.


2. Remove the cover under the steering column using a Phillips screwdriver.


UG3045BA


3-6


Hazard warning flasher


HS3019BA


The hazard warning flasher is used to warn other driv- ers when you have to park your vehicle under emer- gency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the haz- ard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.


Instruments and controls


Meters and gauges (WRX-STi) (cid:132) Combination meter illumination When the ignition switch is turned to the “ON” position, the various parts of the combination meter are illumi- nated in the following sequence: 1. Meter needles and gauge needles light up. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position, and REV indicator flashes. 4. Dials and indicators in meters and gauges light up. 5. “STi” mark lights up. 6. Regular illumination (for driving) begins.


(cid:132) Cancelling sequential illumination of


the combination meter


With the ignition switch in the “ON” position, it is pos- sible to cancel sequential illumination of the combina- tion meter. Press the trip knob while turning the REV setting knob clockwise or counterclockwise. The buzzer will sound briefly, and the outside temperature indicator will show “ON” or “– –”. ON : sequential illumination


– CONTINUED – 3-7


Instruments and controls


– – : sequential illumination cancelled The setting toggles between “ON” and “– –” each time the trip knob is pressed. Return the REV setting knob to its original position to complete the setting process. The buzzer will sound briefly. A few seconds later, the outside temperature indicator will return to showing the outside tempera- ture. NOTE It is not possible to cancel sequential illumination of the combination meter while sequential illumi- nation is actually taking place. Cancel sequential illumination when regular illumination (for driving) has begun.


(cid:132) Speedometer The speedometer shows the vehicle speed.


3-8


(cid:132) Odometer/Trip meter


UG3026BB


1) Trip meter 2) Odometer This meter displays the odometer and two trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position. If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. It is possible switch between the A trip meter and B trip meter indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 sec- onds of illumination of the odometer/trip meter, the


odometer/trip meter will go off. (cid:84) Odometer The odometer shows the total distance that the vehicle has been driven. (cid:84) Double trip meter


B trip meter


A trip meter To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.


Instruments and controls


UG3027AB


1) A trip meter 2) B trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.


To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.


NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.


(cid:132) Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.


Do not operate the engine with the pointer of the tachometer in the red zone. In this range, – CONTINUED – 3-9


Instruments and controls


fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.


contains fuel. The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank. NOTE


(cid:132) Fuel gauge


UG3517BB


1) Low fuel warning light The fuel gauge shows the approximate amount of fuel remaining in the tank. When the ignition switch is in the “LOCK” or “ACC” po- sition, the fuel gauge shows “E” even if the fuel tank


3-10


UG3518AA


” sign in the fuel gauge


You will see the “ meter. This indicates that the fuel filler door (lid) is locat- ed on the right side of the vehicle. (cid:84) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [About 2.3 US gal (9.0 liters, 1.9 Imp gal)].


It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 4.0 US gal (15 liters, 3.3 Imp gal).


Promptly put fuel in the tank whenever the low fuel warning light comes on. If the engine mis- fired as a result of an empty tank, resulting cat- alytic converter damage could cause damage to the turbocharger.


Instruments and controls


(cid:132) Temperature gauge


UG3519BB


1) Normal operating range The temperature gauge shows engine coolant temper- ature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.


– CONTINUED – 3-11


50°C). The indicator can give a false reading under any of the following conditions: (cid:121) When there is too much sun. (cid:121) During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately follow- ing a shutdown. (cid:121) When the actual outside temperature falls outside the specified indicator range.


Instruments and controls


If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possi- ble. See the “In case of emergency” in chapter 9.


(cid:132) Outside temperature indicator


UG3028AB


A) U.S.-spec. models B) Canada-spec. models The outside temperature indicator shows the outside temperature in a range from –22 to 122°F (–30 to


3-12


REV indicator light and buzzer (WRX- STi)


speed enters the tachometer’s red zone.


(cid:132) Setting the alarm-level engine speed


Instruments and controls


UG3522BA


UG3036AA


The REV alarm system issues a warning using the REV indicator light (and a buzzer if additionally select- ed) when the engine speed reaches a level previously set using the REV setting knob. If you press the trip knob when the ignition switch is in the “LOCK” position, the outside temperature indicator will show the engine speed that has already been set. NOTE Even if the REV alarm system is not set, the REV indicator light will come on whenever the engine


1. Turn the REV setting knob clockwise or counter- clockwise, then release it and let it return to its initial position. The buzzer will sound. The REV alarm sys- tem is now ready to be set. 2. Turn the REV setting knob to select the desired alarm-level engine speed. At this time, the outside temperature indicator will show the engine-speed setting.


(cid:121) Counterclockwise (–) for less than 0.5 second: Speed setting changes downward by 100 rpm.


– CONTINUED – 3-13


Instruments and controls


(cid:121) Clockwise (+) for less than 0.5 second: Speed setting changes upward by 100 rpm. (cid:121) Counterclockwise (–) for 0.5 second or longer: Speed setting changes downward by 1,000 rpm. (cid:121) Clockwise (+) for 0.5 second or longer: Speed setting changes upward by 1,000 rpm. The speed setting will stop changing if it reaches 0
rpm or the maximum engine speed.


The alarm-level engine speed can be set (in 100 rpm steps) within a range from 2,000 to 7,500 rpm. The indicator shows the setting as follows:


Speed (rpm)


Indication


00


2,000 2,100


20


21




7,400 7,500


74


75


Approximately three seconds after you stop turning the knob, the REV alarm system will automatically en- ter its next setting mode (step 3 below), in which you can activate or deactivate the buzzer. 3. Activate or deactivate the buzzer as desired using the REV setting knob.


(cid:121) Turn the knob clockwise (+) to activate the buzz- er. The indicator will show “ON”, and the buzzer will sound three times. With the buzzer activated, en-


3-14


gine-speed warnings are given by both the REV in- dicator light and the buzzer. (cid:121) Turn the knob counterclockwise (–) to deactivate the buzzer. The indicator will show “– –”, and the buzzer will not sound. With the buzzer deactivated, engine-speed warnings are given only by the REV indicator light.


Approximately three seconds after you stop turning the knob, the buzzer will sound once to indicate the end of the setting procedure. The indicator will return to showing the outside temperature. Also, the tachometer needle will return to approxi- mately “0”. NOTE (cid:121) The REV alarm system does not operate while settings are being entered. (cid:121) The speed-setting mode terminates if 0 rpm is selected. (cid:121) The speed-setting mode is canceled if the igni- tion switch is turned to OFF or the vehicle starts moving before the setting procedure is finished. (cid:121) Speed setting is impossible when the vehicle is moving. (cid:121) The set engine speed may differ from the engine speed shown by the tachometer. Use the engine speed shown by the tachometer as a rough guide.


Instruments and controls


(cid:132) Deactivating the REV alarm system To deactivate the REV alarm system’s REV indicator light and buzzer functions, set the alarm-level engine speed to 0 (zero) rpm.


Meters and gauges (Except WRX-STi) (cid:132) Speedometer The speedometer shows the vehicle speed.


(cid:132) Odometer/Trip meter


UG3026BB


1) Trip meter 2) Odometer This meter displays the odometer and two trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position.


– CONTINUED – 3-15


Instruments and controls


(cid:84) Odometer The odometer shows the total distance that the vehicle has been driven. (cid:84) Double trip meter


B trip meter


A trip meter To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.


UG3027AB


1) A trip meter 2) B trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.


3-16


To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.


NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.


(cid:132) Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.


Do not operate the engine with the pointer of the tachometer in the red zone. In this range,


fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.


The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank. NOTE


Instruments and controls


(cid:132) Fuel gauge


UG3501BB


Loading...
x