Login- Download PDF Manual
-
mended that you avoid driving with the moonroof fully opened. . If the moonroof cannot be closed through the switch operation because of system failure, it can be closed manually using a hex-head wrench. For the procedure, refer to “Moonroof – if moonroof cannot be closed” F9-19.
Black plate (120,1)
& Sun shade
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Ignition switch ..................................................... LOCK.................................................................. Acc..................................................................... ON...................................................................... START ................................................................ Key reminder chime ............................................ Ignition switch light ............................................. Hazard warning flasher....................................... Meters and gauges.............................................. Combination meter illumination ........................... Canceling the function for meter/gauge needle
movement upon turning on the ignition switch...............................................................
3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-5
3-6
3-63-6
Meter/Gauge needle illumination setting (turbo
3-7
models except STI)............................................ 3-8
Speedometer....................................................... 3-8
Odometer/Trip meter............................................ 3-9
Tachometer ......................................................... Fuel gauge......................................................... 3-10
Temperature gauge (turbo models) ..................... 3-11
REV indicator light and buzzer (STI)................. 3-11
Setting the alarm-level engine speed................... 3-12
Deactivating the REV alarm system..................... 3-13
Warning and indicator lights ............................. 3-13
Seatbelt warning light and chime ........................ 3-14
SRS airbag system warning light ........................ 3-15
Front passenger’s frontal airbag ON and OFF indicators......................................................... 3-16CHECK ENGINE warning light/Malfunction
indicator lamp .................................................. 3-16
Black plate (5,1)
Instruments and controls
Coolant temperature low indicator light (non-
turbo models)/Coolant temperature high warning light (non-turbo models)...................... Charge warning light.......................................... Oil pressure warning light .................................. AT OIL TEMP warning light (AT models).............. Rear differential oil temperature warning light
(STI) ................................................................
Low tire pressure warning light (U.S.-spec.
models) ........................................................... ABS warning light.............................................. Brake system warning light................................ Low fuel warning light ....................................... Hill start assist warning light (MT models – if equipped)/Hill start assist OFF indicator light (STI) ................................................................ Door open warning light .................................... All-Wheel Drive warning light (AT models) .......... Vehicle Dynamics Control operation indicator
light ................................................................
Vehicle Dynamics Control warning light/Vehicle Dynamics Control OFF indicator light/Traction Control OFF indicator light (STI)....................... Security indicator light....................................... SPORT mode indicator light (AT models)............ SI-DRIVE indicator light (STI).............................. Shift-up indicator light (STI) ............................... Select lever/gear position indicator
(AT models) ..................................................... Turn signal indicator lights................................. High beam indicator light ................................... Cruise control indicator light..............................
3-17
3-18
3-18
3-183-19
3-19
3-21
3-21
3-223-22
3-23
3-233-23
3-23
3-25
3-25
3-26
3-263-26
3-26
3-26
3-26北米Model "A1110BE-C" EDITED: 2010/ 11/ 17
Black plate (6,1)
Instruments and controls
Cruise control set indicator light......................... 3-27
Front fog light indicator light (if equipped) .......... 3-27
Headlight indicator light (if equipped) ................. 3-27
Driver’s control center differential auto indicator light (STI) ......................................................... 3-27
Driver’s control center differential indicator and warning lights (STI) .......................................... 3-27
REV indicator light (STI) ..................................... 3-28
Clock ................................................................... 3-28
Information display ............................................ 3-29
Outside temperature indicator ............................ 3-29
Current fuel consumption (if equipped) ............... 3-30
Average fuel consumption .................................. 3-30
Turn off display of fuel consumptionindicator .......................................................... 3-31
Light control switch ........................................... 3-31
Headlights.......................................................... 3-32
High/low beam change (dimmer)......................... 3-32
Headlight flasher ................................................ 3-32Daytime running light system............................. Turn signal lever ................................................ Illumination brightness control......................... Headlight beam leveler (if equipped) ............... Front fog light switch (if equipped) .................. Wiper and washer.............................................. Windshield wiper and washer switches .............. Rear window wiper and washer switch – 5-door ............................................................. Mirrors ................................................................ Inside mirror...................................................... Auto-dimming mirror/compass (if equipped) ....... Auto-dimming mirror/compass with HomeLink®
(if equipped) .................................................... Outside mirrors ................................................. Defogger and deicer.......................................... Tilt/telescopic steering wheel ........................... Horn....................................................................
3-33
3-33
3-33
3-34
3-36
3-36
3-383-39
3-40
3-40
3-403-41
3-47
3-48
3-50
3-51北米Model "A1110BE-C" EDITED: 2010/ 11/ 17
Ignition switch
WARNING
. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the moon- roof or other controls or even make the vehicle move.
CAUTION
Do not attach a large key holder or key case to either key. If it banged against your knees or hands while you are driving, it could turn the ignition switch from the “ON” posi-
if
tion to the “Acc” or “LOCK” posi- tion, thereby stopping the engine. Also, the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch.
The ignition switch has four positions: LOCK, Acc, ON and START. NOTE . Keep the ignition switch in the “LOCK” position when the engine is not running. . Using electrical accessories for a long time with the ignition switch in the “ON” or “Acc” position can cause the
Black plate (125,1)
Instruments and controls 3-3
battery to go dead. . If the ignition switch will not move from the “LOCK” position to the “Acc” position, turn the steering wheel slightly to the left and right as you turn the ignition switch.
& LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turn the steering wheel slightly to the right and left as you turn the key. ! AT models
turning the key is difficult,
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-4 Instruments and controls
The key can be turned from “Acc” to “LOCK” only when the select lever is in the “P” position. ! MT models
The key can be turned from “Acc” to “LOCK” only when the key is pushed in
while turning it.
& Acc In this position the electrical accessories (audio, accessory power outlet, etc.) can be used.
& ON This is the normal operating position after the engine is started.
& START The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
CAUTION
Do not turn the ignition switch to the “START” position while the engine is running.
If your registered key fails to start the engine, pull out the key once (the security indicator light will blink), and then insert the key in the ignition switch and turn it to the “START” position and again try to start the engine.
Black plate (126,1)
NOTE The engine may not start in the follow- ing cases:
. The key grip is touching another key or a metallic key holder.
. The key is near another key that
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
contains an immobilizer transponder. . The key is near or touching another transmitter.
& Key reminder chime The reminder chime sounds when the driver’s door is opened and the ignition switch is in the “LOCK” or “Acc” position.
the following
The chime stops under conditions. . when the ignition switch is turned to the “ON” position . when the key is removed from the ignition switch . when the driver’s door is closed
& Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light illumi- nates when the driver’s door is opened or when the driver’s door is unlocked using the remote keyless entry transmitter.
The light remains illuminated for several tens of seconds and then gradually turns off under the following conditions. . when the driver’s door is closed . when the doors are unlocked using the remote keyless entry transmitter
The light turns off immediately under the
Black plate (127,1)
Instruments and controls 3-5
Hazard warning flasher
following conditions. . when the ignition switch is turned to the “ON” position . when all doors and the rear gate (5- door) are locked using the remote keyless entry transmitter
The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works regard- less of the position of the ignition switch.
To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-6 Instruments and controls
Meters and gauges
NOTE Liquid-crystal displays are used in some of the meters and gauges on the combination meter. You will find their indications hard to see if you wear polarized glasses.
& Combination meter illumina-
tion
When the ignition switch is turned to the “ON” position, the combination meter are illuminated in the following sequence:
the various parts of
Turbo models: 1. Warning lights, indicator lights, meter needles and gauge needles illuminate. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position. 4. Meter and gauge dials, odometer and trip meter back light illuminate. 5. Regular illumination (for driving) be- gins.
Non-turbo models: 1. Warning lights, indicator lights, meter needles, gauge needles, odometer and
Black plate (128,1)
“Acc” position. Press the trip knob to show “ on the odometer and trip meter display.
” or “
”
The display can be switched as shown in the following illustration by pressing the trip knob.
trip meter back light illuminate. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position. 4. Regular illumination (for driving) be- gins.
& Canceling the function for meter/gauge needle move- ment upon turning on the ignition switch
It is possible to activate or deactivate the movement of the meter needles and gauge needles that takes place when the ignition switch is turned to the “ON” position. Turn the ignition switch to the “LOCK” or
*1: STI only ” or *2:
“
”, and “
“ ” cannot be displayed when the ignition switch is in the “ON” position.
” or
“
*3: Turbo models except STI
To change the current setting, press the trip knob for at least 2 seconds.
: Activated
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
if
switch is in the “LOCK” position. The illumination of the needles turns off im- mediately after the ignition switch is turned from the “ON” position to the “LOCK” position. NOTE . Even during the illumination after the driver’s door is opened, the ignition switch is turned to the “ON” position, the combination meter will illuminate as usual. . If the doors are locked by the remote keyless entry system during the illumi- nation after the driver’s door is opened, the illumination will be turned off. . Even while the illumination gradu- ally turns off after the ignition switch is turned to the “LOCK” position, if the ignition switch is turned to the “ON” position, the combination meter illumi- nate as usual. To change the setting: 1. Turn the ignition switch to the “LOCK” or “Acc” position.
: Deactivated
NOTE . Your vehicle’s initial movement setting of the meter/gauge needles has been set for activation “ ” at the time of shipment from the factory. . It is not possible to cancel the initial movement setting of the meter/gauge needles when the ignition switch is in the “ON” position. Cancel the setting when the ignition switch is in the “LOCK” or “Acc” position.
& Meter/Gauge needle illumi-
nation setting (turbo models except STI)
When the setting is activated or deacti- vated, the meter needles and gauge needles illuminate and turn off as follows.
Activated: When the driver’s door is opened while the ignition switch is in the “LOCK” position, the needles illuminate and turn off after approximately 20 seconds. The illumination of the needles gradually turns off after the ignition switch is turned from the “ON” position to the “LOCK” position. Deactivated: The needles do not illuminate when the driver’s door is opened while the ignition
Black plate (129,1)
Instruments and controls 3-7
2. Press the trip knob to show “ ” or “ ” on the odometer and trip meter display. The display can be switched as shown in the following illustration by pressing the trip knob.
*: “
” or “
”, and “
” or “
” cannot
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (130,1)
3-8 Instruments and controls
be displayed when the ignition switch is in the “ON” position.
3. To change the current setting, press the trip knob for at least 2 seconds.
: Activated : Deactivated
NOTE The initial illumination setting of the meter/gauge needles of your vehicle has been set for activation “ ” at the time of shipment from the factory. & Speedometer The speedometer shows the vehicle speed.
& Odometer/Trip meter
the “LOCK”, “Acc” or “ON” position.
If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. is possible to switch the indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 seconds of illumination of the odometer/trip meter, the odometer/trip meter will turn off.
It
The display can be switched as shown in the following illustration by pressing the trip knob.
Turbo models
Non-turbo models 1)
Trip knob
This meter displays the odometer and two trip meters when the ignition switch is in
*1: STI only ” or *2:
“ ” cannot be displayed when the ignition
”, and “
” or
“
“
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
switch is in the “ON” position.
*3: Turbo models except STI ! Odometer
! Double trip meter
The odometer shows the total distance that the vehicle has been driven.
The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2
seconds.CAUTION
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combina-
Black plate (131,1)
Instruments and controls 3-9
tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. This may cause severe da- mage to the engine.
NOTE For non-turbo models, to protect the engine while the select lever is in the “P” or “N” position (for AT models) or the shift lever is in the neutral position (for MT models), the engine is con- trolled so that the engine speed may not become too high even if the accel- erator pedal is depressed hard.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-10 Instruments and controls
& Fuel gauge
Turbo models
When the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge shows “E” even if the fuel tank contains fuel.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank. If you press the trip knob while the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge will light up and indicate the amount of fuel remaining in the tank. If, while the fuel gauge is indicating the amount of fuel remaining in the tank, you (a) do not press the trip knob for 10
seconds or (b) open and close the driver’s door, the fuel gauge indication will turn off. NOTENon-turbo models 1)
Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank.
Black plate (132,1)
” sign in the fuel
You will see the “ gauge meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. ! Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty [approxi- mately 2.6 US gal (10.0 liters, 2.2 Imp gal)].
It only operates when the ignition switch is in the “ON” position. NOTE This light does not turn off unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).
CAUTION
Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (133,1)
& Temperature gauge (turbo
models)
CAUTION
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. Refer to “Engine overheating” F9- 13.
Instruments and controls 3-11
REV indicator light and buz- zer (STI)
1) Normal operating range
The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temperature and driving conditions.
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
light
The REV alarm system issues a warning using the REV indicator (and a buzzer if additionally selected) when the engine speed reaches a level previously set using the trip knob. If you press the trip knob, the odometer/ trip meter will show the engine speed that has already been set.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (134,1)
3-12 Instruments and controls
NOTE Even if the REV alarm system is not set, the REV indicator light will illuminate whenever the engine speed enters the tachometer’s red zone.
& Setting the alarm-level en-
gine speed
1. Push the trip knob to select “REV” on the combination meter.
2. When the trip knob is pushed for more than 2 seconds, the thousands place flashes. 3. Release your finger from the trip knob once, then push and hold the trip knob again. The number will change sequen- tially from 2 to 7. Release your finger at the desired alarm-level engine speed.
the
4. When the trip knob is pushed, hundreds place flashes. 5. Release your from trip knob finger once, then push and hold the trip knob again. The number will change sequen- tially from 0 to 9. Release your finger at the desired alarm-level engine speed. 6. When the trip knob is pushed, the buzzer sounds and the REV alarm system will automatically enter its new setting mode (step 7 below), in which you can activate or deactivate the buzzer.
The alarm-level engine speed can be set (in 100 rpm steps) within the range from 2,000 rpm to 7,000 rpm. 7. Every time that the trip knob is pushed and held, the buzzer changes to activate or deactivate. b – on: Activated b – off: Deactivated When the mode is changed to “activate”, the buzzer sounds. 8. Push the trip knob to complete the setting procedure.
NOTE . The REV alarm system does not operate while settings are being en- tered. . The speed-setting mode terminates if “--00” rpm is selected. . The speed-setting mode is canceled if the ignition switch is turned from ON
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
to OFF, OFF to ON, or the vehicle starts moving before the setting procedure is finished. . Setting the speed is impossible when the vehicle is moving. . The set engine speed may differ from the engine speed shown by the tachometer. Use the engine speed shown by the tachometer as a rough guide. . If the setting operation is performed with the engine switch turned off, the REV indicator light turns off and the setting operation is aborted when you have stopped the setting operation for approximately 10 seconds. . If the setting operation is performed with the engine switch turned off, the REV indicator light turns off and the setting operation is aborted when you open and close the driver’s door. & Deactivating the REV alarm
system
To deactivate the REV indicator light and buzzer functions of the REV alarm system, set the thousands place of the alarm-level engine speed to “–”.
Warning and indicator lights
Several of the warning and indicator lights illuminate momentarily and then turn off when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. For the system check, the following lights illuminate and turn off after several sec- onds or after the engine has started:
: Seatbelt warning light
(The seatbelt warning light only when the driver seatbelt.) : Front passenger’s seatbelt warning
turns off fastens the
light (The seatbelt warning light turns off only when the front seat passenger fastens the seatbelt.)
: SRS airbag system warning light
ON /
: Front passenger’s frontal airbag
ON indicator light
: Front passenger’s frontal airbag
OFF indicator light
: CHECK ENGINE warning light/Mal-
function indicator lamp
Black plate (135,1)
Instruments and controls 3-13
: Coolant temperature high warning light (non-turbo models)
: Charge warning light
: Oil pressure warning light
: AT OIL TEMP warning light
(AT models)
: Rear differential oil temperature warn- ing light (STI)
: Low tire pressure warning light
(U.S.- spec. models)
: ABS warning light
: Brake system warning light
: Low fuel warning light
: Hill start assist warning light
(MT models – if equipped)/Hill start assist OFF indicator light (STI)
: Door open warning light
: AWD warning light (AT models)
: Vehicle Dynamics Control operation
indicator light
: Vehicle Dynamics Control warning light/Vehicle Dynamics Control OFF indicator light/Traction Control OFF indicator light (STI)
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-14 Instruments and controls
: SPORT mode indicator light
(AT models)
: Cruise control indicator light
: Cruise control set indicator light
: Shift-up indicator light (STI)
: REV indicator light (STI) : Driver’s control center differential
indicator and warning lights (STI)
If any lights fail to illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. & Seatbelt warning light
and chime
Your vehicle is equipped with a seatbelt warning device at the driver’s and front passenger’s seat, as required by current safety standards. With the ignition switch turned to the “ON” position, this device reminds the driver and front passenger to fasten their seat- belts by illuminating the warning lights in the locations indicated in the following illustration and sounding a chime.
Driver’s warning light (turbo models)
Driver’s warning light (non-turbo models)
Black plate (136,1)
Front passenger’s warning light ! Operation If the driver and/or front passenger have/ has not yet fastened the seatbelt(s) when the ignition switch is turned to the “ON” position, the seatbelt warning light(s) will flash for 6 seconds, the seatbelt(s) is/are unfastened. the dri- ver’s seatbelt is not fastened, a chime will also sound simultaneously. NOTE . If the driver’s and/or front passen- ger’s seatbelt(s) are/is still not fastened 6 seconds later, the seatbelt warning device operates as follows according to the vehicle speed.
to warn that
If
– At speeds lower than approxi- mately 9 mph (15 km/h)
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
The warning light(s) for unfastened seatbelt(s) will alternate between steady illumination and flashing at 15-second intervals. The chime will not sound. – At speeds higher than approxi- mately 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals and the chime will sound while the warning light(s) is/are flashing.
time, however,
. It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is turned ON next the complete sequence of the warning operation resumes. For further details about canceling the warning operation, please contact your SUBARU dealer. there is no passenger on the front If passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated. The front passenger’s occupant detection system monitors whether or not there is a passenger on the front passenger’s seat. Observe the following precautions. Failure to do so may prevent the device from functioning correctly or cause the device
to fail. . Do not install any accessory such as a table or TV onto the seatback. . Do not store a heavy load in the seatback pocket. . Do not allow the rear seat occupant to place his/her hands or legs on the front passenger’s seatback, or allow him/her to pull the seatback. . Do not use front seats with their back- ward-forward position and seatback not being locked into place securely. If any of them are not locked securely, adjust them again. For adjusting procedure, refer to “Front seats” F1-2.
If the seatbelt warning device for the front passenger’s seat does not function cor- rectly (e.g., it is activated even when the front passenger’s seat is empty or it is deactivated even when the front passen- ger has not fastened his/her seatbelt), take the following actions. . Ensure that no article is placed on the seat other than a child restraint system and its child occupant, although we strongly recommend that all children sit in the rear seat properly restrained. . Ensure that there is no article left in the seatback pocket. . Ensure that the backward-forward po- sition and seatback of front passenger’s
Black plate (137,1)
Instruments and controls 3-15
seat are locked into place securely by moving the seat back and forth.
If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. & SRS airbag system
warning light
WARNING
If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of injury. . Flashing or flickering of the warn-
ing light
. No illumination of
the warning light when the ignition switch is first turned to the “ON” position
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-16 Instruments and controls
. Continuous illumination of
warning light
the
. Illumination of the warning light
while driving
& Front passenger’s frontal
airbag ON and OFF indica- tors
ON /
: Front passenger’s frontal airbag ON indicator
: Front passenger’s frontal airbag OFF indicator
The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located next to the clock in the center portion of the dash-
board. When the ignition switch is turned to the “ON” position, both the ON and OFF indicators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators turn off for 2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the SUBARU ad- vanced frontal airbag system monitoring. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain off. If the front passenger’s SRS frontal airbag the passenger’s frontal is deactivated, airbag ON indicator will remain off while the OFF indicator will illuminate. With the ignition switch turned to the “ON” position, if both the ON and OFF indica- tors remain illuminated or off simulta- neously even after the system check the system is malfunctioning. period, Contact your SUBARU dealer immedi- ately for an inspection.
Black plate (138,1)
& CHECK ENGINE warn- ing light/Malfunction in- dicator lamp
CAUTION
If the CHECK ENGINE light illumi- nates while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle opera- tion without having the emission control system checked and re- paired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
If this light illuminates steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission con- trol system. ! If the light illuminates steadily If the light illuminates steadily while driving or does not turn off after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immedi- ately.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
turn off,
NOTE This light also illuminates when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp illuminat- ing could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not take your vehicle to your authorized SUBARU dealer immediately. ! If the light is blinking If is blinking while driving, an engine misfire condition has been de- tected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the following. . Reduce vehicle speed. . Avoid hard acceleration. . Avoid steep uphill grades. . Reduce the amount of cargo, if possi- ble.
the light
The CHECK ENGINE warning light may stop blinking and illuminate steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. & Coolant temperature
low indicator light (non- turbo models)/Coolant temperature high warn- ing light (non-turbo models)
CAUTION
if
. After turning the ignition switch to the “ON” position, this indicator light/warning light be- haves in any of the following ways, the electrical system may be malfunctioning. Contact your SUBARU dealer immediately for an inspection. – It remains blinking in RED. – It remains illuminated in RED
for more than 2 seconds.
– It remains blinking in RED and
BLUE alternately.
. While driving,
this indicator light/warning light behaves in any of the following ways, take
if
Black plate (139,1)
Instruments and controls 3-17
the specified appropriate mea- sure listed below. – Blinking or illuminated in
RED: Safely stop the vehicle as soon as possible, and refer to the emergency steps to take in the case of engine overheating. After that, have the system checked by your nearest SUBARU dealer. Refer to “Engine overheating” F9- 13.
– Blinking in RED and BLUE
alternately: The electrical system may be malfunctioning. Contact your SUBARU dealer for an inspec- tion.
temperature low indicator temperature high warning
This coolant light/coolant light has the following three functions. . Illumination in BLUE indicates insuffi- cient warming up of the engine . Blinking in RED indicates that engine is close to overheating . Illumination in RED indicates overheat- ing condition of the engine
the
For a system check, this indicator light/ illuminates in RED for warning light – CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-18 Instruments and controls
approximately 2 seconds when the igni- tion switch is turned to the “ON” position. After that, this indicator light/warning light changes to BLUE and maintains illumina- tion in BLUE. This BLUE illuminated light turns off when the engine is warmed up sufficiently.
the engine coolant
If temperature in- creases over the indicator light/warning light blinks in RED. At this time, the engine is close to overheating.
the specified range,
the engine coolant
If temperature in- creases further, the indicator light/warning light illuminates in RED continuously. At this time, the engine may be overheating.
When the indicator light/warning light blinks in RED or illuminates in RED, safely stop the vehicle as soon as possible, and refer to the emergency steps to take in the case of engine overheating. Refer to “Engine overheating” F9-13. After that, have the system checked by your nearest SUBARU dealer.
if
the indicator
Also, light/warning light often blinks in RED, the electrical system may be malfunctioning. Contact your SUBARU dealer for an inspection.
NOTE If the engine is restarted after a certain driving condition, this indicator light/ warning light may illuminate in RED. However, this is not a malfunction if the indicator light/warning light turns off after a short time.
& Charge warning light If this light illuminates when the engine is running, it may indicate that the charging system is not working properly.
If the light illuminates while driving or does not turn off after the engine starts, stop the the first safe opportunity and engine at the belt check the alternator belt. is loose, broken or if is in good condition but the light remains illuminated, contact your nearest SUBARU dealer immediately. & Oil pressure warning
If the belt
light
If this light illuminates when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light illuminates while driving or does not turn off after the engine starts, stop the engine at the first safe opportunity and
Black plate (140,1)
check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains illuminated, contact your nearest SUBARU dealer immediately. For details about checking the engine oil level or adding the engine oil, refer to “Engine oil” F11-10.
CAUTION
Do not operate the engine with the oil pressure warning light illumi- nated. This may cause serious en- gine damage.
& AT OIL TEMP warning
light (AT models)
If this light illuminates when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.
the light
illuminates while driving,
If im- mediately stop the vehicle in a safe place and let the engine idle until the warning light turns off. ! Automatic transmission control
system warning
If the “AT OIL TEMP” warning light flashes after the engine starts, it may indicate that the automatic transmission control system
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
is not working properly. Contact your nearest SUBARU dealer for service im- mediately. & Rear differential oil
temperature warning light (STI)
CAUTION
Reduce vehicle speed and park the vehicle in a safe place as soon as possible if the R.DIFF TEMP light illuminates. Continued driving with this light illuminated can damage the rear differential and other parts of the powertrain.
it may indicate that
If this light illuminates when the engine is running, the rear differential oil temperature is too hot. the driver’s control center At differential will automatically cancel the current torque-distribution ratio setting and adopt its minimum ratio.
this time,
If the light illuminates while driving, reduce vehicle speed and stop the vehicle at the nearest safe place. Park the vehicle for several minutes. After the light turns off, you can start driving. If the light does not turn off, contact the nearest SUBARU dealer for service.
NOTE . If the tire pressures are not correct and/or the tires are not all the same size and brand, the rear differential will be heavily loaded when the vehicle is driven, resulting in an abnormally high oil temperature. . The rear differential oil will deterio- rate if its temperature increases en- ough for the rear differential oil tem- perature warning light to illuminate. It is advisable to have the rear differential oil replaced as soon as possible.
& Low tire pressure
warning light (U.S.-spec. models)
When the ignition switch is turned to the “ON” position, the low tire pressure warn- ing light will illuminate for approximately 2
seconds to check that the tire pressure monitoring system (TPMS) is functioning properly. If there is no problem and all tires are properly inflated, the light will turn off. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufac- turer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated onBlack plate (141,1)
Instruments and controls 3-19
the vehicle placard or tire inflation pres- sure label, you should determine the proper those tires.)
tire inflation pressure for
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under- inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. the TPMS is not a Please note that tire maintenance, substitute for proper is the driver’s responsibility to and it maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is com- bined with the low tire pressure telltale. When the system detects a malfunction, – CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-20 Instruments and controls
the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of re- placement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible.
WARNING
this light does not
If illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blinking for approxi- mately one minute, you should have your Tire Pressure Monitoring Sys- tem checked at a SUBARU dealer as
this light still
soon as possible. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. If illuminates while driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the Low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. If the light illuminates steadily after blinking for approximately one min- ute, promptly contact a SUBARU
Black plate (142,1)
dealer to have the system inspected.
CAUTION
The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked peri- odically (at least monthly) using a tire gauge. After any change to tire pressure(s), the tire pressure mon- itoring system will not re-check tire inflation pressures until the vehicle is first driven more than 20 mph (32
km/h). After adjusting the tire pres- sures, increase the vehicle speed to at least 20 mph (32 km/h) to start the TPMS re-checking of the tire infla- tion pressures. If the tire pressures are now above the severe low pressure threshold, the low tire pressure warning light should turn off a few minutes later. Therefore, be sure to install the specified size for the front and rear tires.北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
& ABS warning light
CAUTION
. If any of the following conditions occur, we recommend that you have the ABS system repaired at the first available opportunity by your SUBARU dealer. – The warning light does not illuminate when the ignition switch is turned to the “ON” position.
– The warning light illuminates when the ignition switch is turned to the “ON” position, but it does not turn off even when the vehicle speed ex- ceeds approximately 8 mph (12 km/h).
– The warning light illuminates
during driving.
. When the warning light is on (and the brake system warning light is off), the ABS function shuts down. However, the conventional brake system continues to oper- ate normally.
With a vehicle equipped with an EBD system, the ABS warning light illuminates
refer
together with the brake system warning light if the EBD system malfunctions. For the EBD system mal- further details of to “Electronic function warning, Brake Force Distribution (EBD) system warning” F3-22. NOTE If the warning light behavior is as described in the following conditions, the ABS system may be considered normal. . The warning light illuminates right after the engine is started but turns off immediately, remaining off. . The warning light remains illumi- nated after the engine has been started, but it turns off when the vehicle speed reaches approximately 8 mph (12
km/h). . The warning light illuminates during driving, but it turns off immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may illumi- nate. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will turn off.Black plate (143,1)
Instruments and controls 3-21
& Brake system warning light
WARNING
. Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains illuminated, have the brakes inspected by a SUBARU dealer immediately.
. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re- pair.
This light has the following functions. ! Parking brake warning The light illuminates with the parking brake applied while the ignition switch is in the “ON” position. It turns off when the parking brake is fully released. ! Brake fluid level warning This light illuminates when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-22 Instruments and controls
If
this occurs,
If the brake system warning light should illuminate while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. immediately stop the vehicle at the nearest safe place and check the brake fluid level. If the fluid is below the “MIN” mark in the level reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution
(EBD) system warning
The brake system warning light also illuminates if a malfunction occurs in the EBD system. In that event, it illuminates together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS warning light illuminate simultaneously,
take the following steps. 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the parking brake and then restart it. 3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair. & Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty approxi- mately 2.6 US gal (10.0 liters, or 2.2 Imp gal). It only operates when the ignition switch is in the “ON” position. When this
the brake fluid level
If
Black plate (144,1)
light illuminates, fill the fuel tank immedi- ately. NOTE This light does not turn off unless the tank is replenished up to an internal fuel quantity of approximately 3.7 US gal (14 liters, 3.1 Imp gal).
CAUTION
Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine.
& Hill start assist warning
light (MT models – if equipped)/Hill start as- sist OFF indicator light (STI)
! Hill start assist warning light While the engine is rotating, if there are any malfunctions in the Hill start assist system, the light will illuminate.
WARNING
When the Hill start assist warning
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
light illuminates, have the vehicle inspected at an authorized SUBARU dealer.
! Hill start assist OFF indicator light
(STI)
While the Hill start assist system is deactivated, the Hill start assist OFF indicator light illuminates continuously to inform the driver that the Hill start assist system is not operational. & Door open warning
light
The door open warning light illuminates if any door or the rear gate is not fully closed.
Always make sure this light is not illumi- nated before you start to drive. & All-Wheel Drive warn- ing light (AT models)
This light illuminates when All-Wheel Drive is disengaged and the drive me- chanism is switched to Front Wheel Drive for maintenance or similar purposes. It flashes if the vehicle is driven with tires of differing diameters fitted on the wheels or with an excessively low air pressure in any of the tires.
CAUTION
Continuing to drive with the AWD warning light flashing can damage the powertrain. If the AWD warning light starts to flash, promptly park in a safe place and check whether the tires have differing diameters and whether any of the tires has an excessively low inflation pressure.
& Vehicle Dynamics
Control operation indi- cator light
It blinks when the skid suppression func- tion is activated. It illuminates only when the traction control function is operating. The Vehicle Dynamics Control system is probably malfunctioning under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The light does not illuminate when the ignition switch is turned to the “ON” position. . The light does not turn off even after a period of approximately 2 seconds after the ignition switch has been turned to the “ON” position.
Black plate (145,1)
Instruments and controls 3-23
& Vehicle Dynamics
Control warning light/ Vehicle Dynamics Con- trol OFF indicator light/ Traction Control OFF in- dicator light (STI)
indicating that
This warning light has both the function of indicating malfunctions in the Vehicle Dynamics Control system and the function of the Vehicle Dynamics Control system has been deactivated or only the Traction Control system has been deactivated. It illuminates in the event of a malfunction in the system and is on when the Vehicle Dynamics Control system is not operating or only the Traction Control system is not operating.
STI: This warning light illuminates in yellow for approximately 1 second when the ignition switch is turned to the “ON” position. After that, this warning light changes to green and remains illuminated in green for 1
second, and then turns off. It indicates that the Vehicle Dynamics Control system is operating normally.– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (146,1)
3-24 Instruments and controls
! Vehicle Dynamics Control warning
light (yellow)
CAUTION
The Vehicle Dynamics Control sys- tem provides its ABS control through the electrical circuit of the ABS system. Accordingly, if the ABS is inoperative, the Vehicle Dynamics Control system becomes unable to provide ABS control. As a result, the Vehicle Dynamics Control system also becomes inoperative, causing the warning light to illuminate. Though both the Vehicle Dynamics Control and ABS systems are inop- erative in this case, the ordinary functions of the brake system are still available. You will be safe while driving with this condition, but drive carefully and have your vehicle checked at a SUBARU dealer as soon as possible.
NOTE . If the electrical circuit of the Vehicle Dynamics Control system itself mal- functions, the warning light only illumi- nates. At this time, the ABS (Anti-lock Brake System) remains fully opera- tional.
. The warning light illuminates when the electronic control system of the ABS/Vehicle Dynamics Control system malfunctions. The Vehicle Dynamics Control system is probably inoperative under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The warning light does not illuminate when the ignition switch is turned to the “ON” position. . The warning light illuminates while the vehicle is running. NOTE If the warning light behavior is as described below, the Vehicle Dynamics Control system may be considered normal. . The warning light illuminates right after the engine is started but turns off immediately, remaining off. . The warning light illuminates after engine startup and turns off while the vehicle is subsequently being driven. . The warning light illuminates during driving, but it turns off immediately and remains off.
! Vehicle Dynamics Control OFF in-
dicator light (yellow)
. This light illuminates when the Vehicle Dynamics Control OFF switch is pressed (except STI). . This light illuminates when the Vehicle Dynamics Control mode switch is pressed for more than 2 seconds (STI). . The light illuminates when the Vehicle Dynamics Control system is deactivated. NOTE . The light may remain illuminated for a while after the engine has been started, especially in cold weather. This does not indicate the existence of a problem. The light should turn off as soon as the engine has warmed up. . The indicator light illuminates when the engine has developed a problem and the CHECK ENGINE warning light/ malfunction indicator lamp is on. The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not turn off even after the lapse of several minutes (the engine has warmed up) after the engine has started.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
! Traction Control OFF indicator light
(green – STI)
The light illuminates when the Vehicle Dynamics Control mode switch is pressed briefly. For details, refer to “Traction mode” F7-36. & Security indicator light
Turbo models
Non-turbo models
The security indicator light deters potential thieves by indicating that the vehicle is equipped with an immobilizer system. It begins flashing (approximately once every 3 seconds) approximately 60 seconds after the ignition switch is turned from the “ON” position to the “Acc” or “LOCK” position or immediately after the key is pulled out. If the security indicator light does not flash, the immobilizer system may not be func- tioning properly. this occurs, contact your SUBARU dealer as soon as possible.
If
In case an unauthorized key is used (e.g., an imitation key), the security indicator light illuminates.
Black plate (147,1)
Instruments and controls 3-25
NOTE . For the flashing pattern when arm- ing the alarm system, refer to “Arming the system” F2-17. . Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally.
& SPORT mode indicator
light (AT models)
lever is moved to the When the select the SPORT mode is se- manual gate, lected and the indicator light illuminates. Refer to “SPORT mode” F7-28.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (148,1)
3-26 Instruments and controls
& SI-DRIVE indicator light (STI)
& Select lever/gear position in-
dicator (AT models)
& Turn signal indicator
lights
Intelligent (I) mode
1) 2) Sport (S) mode 3) Sport Sharp (S#) mode
This light indicates the current SI-DRIVE mode. For details of SI-DRIVE mode, refer to “SI- DRIVE (STI)” F7-28. & Shift-up indicator light
(STI)
While selecting the Intelligent (I) mode of SI-DRIVE, this indicator light illuminates and informs the driver about the upshift timing for fuel-efficient driving.
When the ignition switch is turned to the “ON” position, all of the select lever/gear position indicators illuminate for 2 sec- onds, and then the indicator shows the position of the select lever. When the manual mode is selected, the gear position indicator (which shows the current gear selection) and the upshift/ downshift to “Automatic transmission” F7-22.
light up. Refer
indicator
These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to “Replacing bulbs” F11-47. & High beam indicator
light
This light shows that the headlights are in the high beam mode. This indicator light also illuminates when the headlight flasher is operated. & Cruise control indica-
tor light
This light illuminates when the “CRUISE” main switch is pressed. NOTE . If you press the “CRUISE” main switch button while turning the ignition switch “ON”, the cruise control func- tion is deactivated and the cruise indicator light flashes. To re-
