2009 Subaru Forester Owners Manual

When down shifting, ensure that the vehicle is not travelling at a speed exceeding the Maximum Allowable Speed for the gear which is about to be selected. Failure to observe this precaution can lead to engine over- revving and this in turn can result in engine damage.

Black plate (231,1)

Starting and operating 7-19

Turbo models

mph (km/h)

Gear position Manual mode

36 (58)

66 (106)

107 (172)

“D” position

28 (45)

65 (105) 106 (170)

NOTE In order to prevent over-revving during deceleration of the vehicle, the trans- mission will remain in the current gear if the speed of the vehicle is in excess of the Maximum Allowable Speed for the gear to which the selector lever has been moved.

& Driving tips . On a road surface where there is a risk of wheelspin (for example, a snow- or gravel-covered road), you can pull away from a standstill (safely and easily) by first selecting the 2nd gear of the manual mode. . Always apply the foot or parking brake when the vehicle is stopped in the “D” or “R” position. . Always set the parking brake when parking your vehicle. Do not hold the vehicle with only the transmission. . Do not keep the vehicle in a stationary – CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

7-20 Starting and operating

position on an uphill grade by using the “D” position. Use the brake instead. . The engine may, on rare occasions, knock when the vehicle rapidly acceler- ates or rapidly pulls away from a standstill. This phenomenon does not indicate a problem.

& SPORT mode

When selected, the SPORT mode indica- tor light on the combination meter will turn on. To deselect SPORT mode, move the selector lever to the “D” position or select manual mode. To subsequently reselect SPORT mode, move the selector lever to the “D” position and from there to the manual gate. In this mode, the transmission shifts up at higher vehicle speeds and shifts down more responsively than in normal mode.

SPORT mode is used when power is needed for rapid acceleration or for uphill driving. To select this mode, move the selector lever from the “D” position to the manual gate.

Black plate (232,1)

& Shift lock release If the selector lever does not move from the “P” position with the brake pedal depressed and the ignition switch in the “ON” position, perform the following steps: To override the shift lock: 1. Set engine. 2. Take out the screwdriver from the tool bag.

the parking brake and stop the

3. Remove the cover by prying on the edge with a flat-head screwdriver.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Power steering

it will

The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but take much more effort. NOTE Right after the engine has been started and before it has warmed up, you may hear a noise coming from areas adja- cent to the power steering pump which is located at the right-front area of the engine compartment. This noise is normal. indicate power steering system trouble.

It does not

CAUTION

Do not hold the steering wheel at the fully locked position left or right for more than 5 seconds. This may damage the power steering pump.

Insert the screwdriver into the hole.

4. 5. Push down on the screwdriver and move the selector lever from the “P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine.

Take your vehicle to the nearest SUBARU dealer immediately to have the system repaired.

Black plate (233,1)

Starting and operating 7-21

Braking & Braking tips

WARNING

Never rest your foot on the brake pedal while driving. This can cause dangerous overheating of the brakes and needless wear on the brake pads and linings.

! When the brakes get wet When driving in rain or after washing the vehicle, the brakes may get wet. As a result, brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes. ! Use of engine braking Remember to make use of engine braking in addition to foot braking. When descend- ing a grade, if only the foot brake is used, the brakes may start working improperly because of brake fluid overheating, caused by overheated brake pads. To help prevent this, shift into a lower gear to get stronger engine braking. ! Braking when a tire is punctured Do not depress the brake pedal suddenly when a tire is punctured. This could cause – CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (234,1)

7-22 Starting and operating

a loss of control of the vehicle. Keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.

& Brake system ! Two separate circuits Your vehicle has two separate circuit brake systems. Each circuit works diag- onally across the vehicle. If one circuit of the brake system should fail, the other half of the system still works. If one circuit fails, the brake pedal will go down much closer to the floor than usual and you will need to press it down much harder. And a much longer distance will be needed to stop the vehicle. ! Brake booster The brake booster uses engine manifold vacuum to assist braking force. Do not turn off the engine while driving because that will turn off the brake booster, result- ing in poor braking power. The brakes will continue to work even when the brake booster completely stops functioning. If this happens, however, you will have to push the pedal much harder than normal and the braking distance will increase.

! Brake assist system

WARNING

Do not be overconfident about the brake assist. It is not a system that brings more braking ability to the vehicle beyond its braking capabil- ity. Always use the utmost care when driving regarding vehicle speed and safe distance.

cate any malfunctions, and the brake assist system is operating properly. . You might feel that the brake pedal is applied by lighter force and gener- ates a greater braking force. . You might hear clicking (knocking) sounds around brake pedal.

& Disc brake pad wear warning

indicators

CAUTION

When you need to brake suddenly, continue depressing the brake pedal strongly to bring the effect of the brake assist.

Brake assist is a driver assistance system. It assists the brake power when the driver cannot depress the brake pedal strongly and the brake power is insufficient. Brake assist generates the brake power according to the speed at which the driver depresses the brake pedal. NOTE When you depress the brake pedal strongly or suddenly, the following phenomena occur. However, even though these occur, they do not indi-

The disc brake pad wear warning indica- tors on the disc brakes give a warning noise when the brake pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle checked by your SUBARU dealer.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

ABS (Anti-lock Brake Sys- tem)

The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road sur- faces. This helps prevent the loss of steering control and directional stability caused by wheel lock-up.

When the ABS system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal. This is normal when the ABS operates.

The ABS system will not operate when the vehicle speed is below approximately 6
mph (10 km/h).

WARNING

Always use the utmost care in driving – overconfidence because you are driving with an ABS equipped vehicle could easily lead to a serious accident.

CAUTION

. The ABS system does not always decrease stopping distance. You should always maintain a safe following distance from other

vehicles.

. When driving on badly surfaced roads, gravel roads, icy roads, or over deep newly fallen snow, stopping distances may be long- er for a vehicle with the ABS system than one without. When driving under these conditions, therefore, reduce your speed and leave ample distance from other vehicles.

. When you feel the ABS system operating, you should maintain constant brake pedal pressure. Do not pump the brake pedal since doing so may defeat the operation of the ABS system.

& ABS system self-check Just after the vehicle is started, you may feel on the brake pedal a vibration similar to when the ABS operates, and you may also hear the sound of the ABS working from the engine compartment. This is caused by an automatic functional test of the ABS system being carried out and does not indicate any abnormal condition.

Black plate (235,1)

Starting and operating 7-23

& ABS warning light

The ABS warning light illuminates when the ignition switch is turned to the “ON” position and turns off after approximately 2
seconds. This is an indication that the ABS system is working properly. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may illumi- nate. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will turn off.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (236,1)

7-24 Starting and operating

CAUTION

If the warning light behaves as described below, the ABS system may not be working properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system con- tinues to operate normally. . The warning light does not illu- minate when the ignition switch is turned to the “ON” position.

. The warning light

illuminates when the ignition switch is turned to the “ON” position, but it does not turn off even when the vehicle speed exceeds approxi- mately 8 mph (12 km/h).

. The warning light illuminates dur-

ing driving.

If these occur, have the ABS system repaired at the first available oppor- tunity by your SUBARU dealer.

NOTE If the warning light behavior is as described below, the ABS system may be considered normal. . The warning light illuminates right after the engine is started but turns off immediately, remaining off. . The warning light remains on after the engine has been started, but it turns off when the vehicle speed reaches approximately 8 mph (12
km/h). . The warning light illuminates during driving, but it turns off immediately and remains off.

Electronic Brake Force Dis- tribution (EBD) system

The EBD system maximizes the effective- ness of the brakes by allowing the rear brakes to supply a greater proportion of the braking force. It functions by adjusting the distribution of braking force to the rear wheels in accordance with the vehicle’s loading condition and speed. The EBD system is an integral part of the ABS system and uses some of the ABS system’s components to perform its func- tion of optimizing the distribution of brak- ing force. If any of the ABS components used by the EBD function fail, the EBD system also stops working.

When the EBD system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal. This is normal and does not indicate a malfunction.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Steps to take if EBD system

fails

If a malfunction occurs in the EBD system, the system stops working and the brake system warning light and ABS warning light illuminate simultaneously.

The EBD system may be faulty if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS

Black plate (237,1)

Starting and operating 7-25

may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately.

. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re- pair.

illuminate simultaneously,

warning light take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the parking brake and then restart it. 3. Release the parking brake. If both warning lights turn off, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and stay illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair.

the brake fluid level

If

WARNING

. Driving with the brake system warning light on is dangerous. This indicates your brake system

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (238,1)

7-26 Starting and operating

Vehicle Dynamics Control system

WARNING

Always use the utmost care in driving – overconfidence because you are driving with a Vehicle Dy- namics Control system equipped vehicle could easily lead to a ser- ious accident.

CAUTION

. Even if your vehicle is equipped with Vehicle Dynamics Control, winter tires or snow chains should be used when driving on snow-covered or icy roads; in addition, vehicle speed should be reduced considerably. Simply having a Vehicle Dynamics Con- trol system does not guarantee that the vehicle will be able to avoid accidents in any situation. the Vehicle Dy- namics Control system is an indication that the road being travelled on has a slippery sur- face; since having Vehicle Dy- namics Control is no guarantee

. Activation of

that full vehicle control will be maintained at all times and under all conditions, its activation should be seen as a sign that the speed of the vehicle should be reduced considerably.

. Whenever suspension compo- nents, steering components, or an axle are removed from a vehicle equipped with Vehicle Dynamics Control, have an authorized SUBARU dealer per- form an inspection of that sys- tem.

. The following precautions should be observed in order to ensure that the Vehicle Dynamics Con- trol system is operating properly: – All four wheels should be fitted with tires of the same size, type, and brand. Further- more, the amount of wear should be the same for all four tires.

– Keep the tire pressure at the proper level as shown on the vehicle placard attached to the driver’s side door pillar.

– Use only the specified tem- porary spare tire to replace a flat tire. With a temporary

spare tire, the effectiveness of the Vehicle Dynamics Control system is reduced and this should be taken into account when driving the vehicle in such a condition.

In the event of wheelspin and/or skidding on a slippery road surface and/or during cornering and/or an evasive maneuver, the Vehicle Dynamics Control system adjusts the engine’s output and the wheels’ respective braking forces to help maintain traction and directional control. . Traction Control Function The traction control function is designed to prevent spinning of the driving wheels on slippery road surfaces, thereby helping to maintain traction and directional control. Activation of this function is shown by steady illumination of the Vehicle Dy- namics Control operation indicator light. . Skid Suppression Function The skid suppression function is designed to help maintain directional stability by suppressing the wheels’ tendency to slide sideways during steering operations. Acti- vation of this function is shown by flashing of the Vehicle Dynamics Control operation indicator light.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

NOTE . Slight twitching of the brake pedal may be felt when the Vehicle Dynamics Control system operates; a small de- gree of vehicle or steering wheel shak- ing may also be noticed in this situa- tion. These are normal characteristics of Vehicle Dynamics Control operation and are no cause for alarm. . When driving off immediately after starting the engine, a short-lived opera- tion noise may be noticed coming from the engine compartment. This noise is generated as a result of a check being performed on the Vehicle Dynamics Control system and is normal. . Depending on the timing of activa- tion of the brakes, the brake pedal may seem to jolt when you drive off after starting the engine. This is a conse- quence of the Vehicle Dynamics Con- trol operational check and is normal. . In the circumstances listed in the the vehicle may be more following, unstable than it feels to the driver. The Vehicle Dynamics Control System may therefore operate. Such operation does not indicate a system fault.

– on gravel-covered or roads – on unfinished roads – when the vehicle is fitted with

rutted

snow tires or winter tires

. Activation of the Vehicle Dynamics Control system will cause operation of the steering wheel to feel slightly different compared to that for normal conditions. . Even if the vehicle is equipped with a Vehicle Dynamics Control system, it is important that winter tires be used when driving on snow-covered or icy roads. (All four wheels should be fitted with tires of the same size and brand.) Furthermore, if snow chains are to be used, they should be fitted on the front wheels. When a vehicle is fitted with snow chains, however, the effective- ness of the Vehicle Dynamics Control system is reduced and this should be taken into account when driving the vehicle in such a condition. . It to reduce is always important speed when approaching a corner, even if the vehicle is equipped with Vehicle Dynamics Control. . All four wheels should be fitted with tires of the same size, type, and brand; furthermore, the amount of wear should be the same for all four tires. If these precautions are not observed and non-matching tires are used, it is quite possible that the Vehicle Dy- namics Control system will be unable

Black plate (239,1)

Starting and operating 7-27

to operate correctly as intended. . Always turn off the engine before replacing a tire as failure to do so may render the Vehicle Dynamics Control system unable to operate correctly.

& Vehicle Dynamics Control

system monitor

! Vehicle Dynamics Control opera-

tion indicator light

The indicator light illuminates when the ignition switch is turned to the ON position; it turns off approximately 2 seconds later. This indicator light flashes during activa- tion of the skid suppression function and is illuminated steadily during activation of the traction control function. The following two situations could indicate – CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (240,1)

7-28 Starting and operating

the Vehicle Dynamics a malfunction of Control system; if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. . The indicator light does not illuminate when the ignition switch is turned to the ON position. . The indicator light does not turn off approximately 2 seconds after the ignition switch has been turned to the ON position. ! Vehicle Dynamics Control warning light/Vehicle Dynamics Control OFF indicator light

This single light has the function of indicating malfunctions in the Vehicle Dynamics Control system and the function of the Vehicle Dynamics

indicating that

Control system is not operating. It illumi- nates in the event of a malfunction in the system and is illuminated whenever the system is not operating. ! Vehicle Dynamics Control warning

light

The warning light illuminates when the ignition switch is turned to the “ON” position and turns off several seconds after engine startup. This lighting pattern indicates that the Vehicle Dynamics Con- trol system is operating normally.

The following situations could indicate a malfunction of the Vehicle Dynamics Control system; if any should occur, have an authorized SUBARU dealer carry out an inspection of the system at the first available opportunity. . The warning light does not turn on when the ignition switch is turned to the ON position. . The warning light turns on while the vehicle is being driven. . When a malfunction has occurred in the Vehicle Dynamics Control electrical system, only the warning light will turn on. In such an event, the ABS will still be operating normally. . The warning light will also turn on when a problem occurs with the ABS or Vehicle Dynamics Control electronic control sys-

tems.

Because the Vehicle Dynamics Control system controls each brake through the ABS, whenever the ABS stops operating due to a malfunction in that electrical system, the Vehicle Dynamics Control will also become unable to control all four brakes. Thus Vehicle Dynamics Control system operation halts and the warning light turns on. Although both the Vehicle Dynamics Control system and the ABS will be inoperable in this situation, it will still be possible to stop the vehicle using normal braking. The Vehicle Dynamics Control system and the ABS do not adversely affect operation of the vehicle in any way when they are inoperable; however should such a situation occur, drive with care and have an authorized SUBARU dealer carry out an inspection of those systems at the first available oppor- tunity. NOTE When the warning light turns on and off in the following way, it indicates that the Vehicle Dynamics Control system is operating normally. . Although turning on after the engine has been started, the warning light quickly turns off and stays off. . The warning light turns on when the

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

vehicle is being driven; it then turns off and stays off. ! Vehicle Dynamics Control OFF in-

dicator light

This light illuminates to indicate that the Vehicle Dynamics Control system is in non-operation mode. This does not con- stitute failure of the Vehicle Dynamics Control system. NOTE . The indicator light may stay on for a while after the engine has been started, especially in cold weather. This occurs because the engine has not yet warmed up and is completely normal. The light will turn off when the engine has reached a suitable operating tem- perature. . When an engine problem occurs and the CHECK ENGINE warning light/ malfunction indicator lamp turns on, the indicator light will also illuminate. The following two situations could indicate the Vehicle Dynamics malfunction of Control system; if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. . The indicator light does not turn on when the ignition switch is turned to the

ON position. . The indicator light fails to turn off after the engine is started, even when several minutes have passed to allow the engine to heat up sufficiently.

& Vehicle Dynamics Control

OFF switch

Pressing the switch to deactivate the Vehicle Dynamics Control system can facilitate the following operations: . a standing start on a steeply sloping road with a snowy, gravel-covered, or otherwise slippery surface . extrication of wheels are stuck in mud or deep snow

the vehicle when its

When the switch is pressed during engine operation, the “ ” indicator light on the

Black plate (241,1)

Starting and operating 7-29

combination meter illuminates. The Vehi- cle Dynamics Control system will be deactivated and the vehicle will behave like a model not equipped with the Vehicle Dynamics Control system. When the switch is pressed again to reactivate the Vehicle Dynamics Control system, the “ ” indicator light turns off. With the Vehicle Dynamics Control system deactivated, traction and stability en- hancement offered by Vehicle Dynamics Control system is unavailable. Therefore you should not deactivate the Vehicle Dynamics Control system except under above-mentioned situations. NOTE . When the switch has been pressed to deactivate the Vehicle Dynamics Control system, the Vehicle Dynamics Control system automatically reacti- vates itself the next time the ignition switch is turned to the “LOCK” position and the engine is restarted. . If the switch is held down for 10
seconds or longer, the indicator light turns off, the Vehicle Dynamics Control system is activated, and the system ignores any further pressing of the switch. To make the switch usable again, turn the ignition switch to the “LOCK” position and restart the en-

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

7-30 Starting and operating

gine. . When the switch is pressed to deactivate the Vehicle Dynamics Con- trol system, the vehicle’s running per- formance is comparable with that of a vehicle that does not have a Vehicle Dynamics Control system. Do not de- activate the Vehicle Dynamics Control system except when absolutely neces- sary.

Tire pressure monitoring system (TPMS) (U.S.-spec. models)

The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low. The tire pressure monitoring system will activate only when the vehicle is driven at speeds above 20 mph (32 km/h). Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused by running over a sharp object).

Black plate (242,1)

WARNING

If the low tire pressure warning light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually redu- cing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. Check the pressure for all four tires and adjust the pressure to the COLD tire pressure shown on the tire placard on the door pillar on the driver’s side. Even when the vehicle is driven a very short distance, the tires get warm and their pressures increase accordingly. Be sure to let the tires cool thoroughly before adjusting their pressures to the standard values shown on the tire placard. Refer to the “Tires and wheels” section in chapter 11. The tire pres- sure monitoring system does not function when the vehicle is station- ary. After adjusting the tire pres- sures, increase the vehicle speed to at least 20 mph (32 km/h) to start the TPMS re-checking of the tire infla- tion pressures. If the tire pressures

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

this light still

are now above the severe low pressure threshold, the low tire pressure warning light should turn off a few minutes later. If illuminates while driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately 1 minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or sys- tem resetting. Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light illuminates steadily after blinking for approximately 1 minute, promptly contact a SUBARU dealer to have the system inspected.

CAUTION

Do not place metal film or any metal parts in the cargo room/trunk. This may cause poor reception of the signals from the tire pressure sen- sors, and the tire pressure monitor- ing system will not function prop- erly.

NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful inter- this device must ference, and (2) accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

Black plate (243,1)

Starting and operating 7-31

Parking your vehicle & Parking brake To set the parking brake, press the brake pedal the firmly and hold it down until parking brake lever is fully pulled up.

To release the parking brake, pull the lever up slightly, press the release button, then lower the lever while keeping the button pressed. When the parking brake is set while the engine is running, the parking brake warning light illuminates. After starting the vehicle, be sure that the warning light has gone out before the vehicle is driven. Refer to the “Warning and indicator lights” section in chapter 3.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

7-32 Starting and operating

CAUTION

Never drive while the parking brake is set because this will cause un- necessary wear on the brake lin- ings. Before starting to drive, always make sure that the parking brake has been fully released.

& Parking tips When parking your vehicle, always set the parking brake firmly and put the shift lever in the “1” (1st) for an upgrade or “R” (Reverse) for a downgrade for manual transmission vehicles, or in the “P” (Park) position for automatic transmission vehi- cles. Always set the parking brake firmly when parking your vehicle. Never rely on the transmission alone to hold the vehicle.

When parking on a hill, always turn the steering wheel. When the vehicle is headed up the hill, the front wheels should be turned away from the curb.

Black plate (244,1)

WARNING

. Never leave unattended children or pets in the vehicle. They could accidentally injure themselves or others through inadvertent op- eration of the vehicle. Also, on hot or sunny days, the tempera- ture in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people.

. Do not park the vehicle over flammable materials such as dry grass, waste paper or rags, as they may burn easily if they come near hot engine or exhaust sys- tem parts.

. Be sure to stop the engine if you take a nap in the vehicle. If engine exhaust gas enters the passenger compartment, occu- pants in the vehicle could die from carbon monoxide (CO) con- tained in the exhaust gas.

When facing downhill, should be turned into the curb.

the front wheels

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

CAUTION

If your vehicle has a front under- spoiler and rear underspoiler (both optional), pay attention to blocks and other obstructions on the ground when parking. The under- spoilers could be damaged by con- tact with them.

Hill start assist system (MT vehicles)

CAUTION

The Hill start assist system is a device only for helping the driver to START the vehicle on an uphill grade. To prevent accidents when the vehicle is parked on a slope, be sure to firmly set the parking brake. When setting the parking brake, make sure that the vehicle remains stationary when the clutch pedal is released.

The Hill start assist system is a device to make starting on an uphill grade easier.

Black plate (245,1)

Starting and operating 7-33

On an uphill grade, when the clutch pedal is depressed while the brake pedal is also depressed, braking power is maintained temporarily by the Hill start assist system when the brake pedal is released. The driver is therefore able to start the vehicle the same way as on a level grade, just using the clutch and accelerator pedal.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (246,1)

7-34 Starting and operating

& Hill start assist warning light

Cruise control

When the ignition switch is turned to the “ON” position, the Hill start assist warning light illuminates and turns off after approxi- mately 2 seconds. While the engine is rotating, if any malfunction is detected in the Hill start assist system control, the warning light will illuminate. If the warning light illuminates, have the vehicle in- spected by your SUBARU dealer.

The Hill start assist system does not operate when the vehicle is facing down- hill. And the Hill start assist system may not operate on slight grades.

When starting in reverse and using the Hill start assist system, a braking effect may be felt even after the brake pedal has been released. However, this braking effect should disappear once the clutch pedal is released.

A slight jolt may be felt when the vehicle begins to move forward after being re- versed.

If the braking power of the Hill start assist system is insufficient after the brake pedal is released, apply more braking power by pressing the brake pedal again.

is not

Cruise control enables you to maintain a constant vehicle speed without holding your foot on the accelerator pedal and it is operative when the vehicle speed is 25
mph (40 km/h) or more. Make sure the main switch is turned “OFF” when the cruise control in use to avoid unintentionally setting the cruise control. NOTE If you press the main switch button while turning the ignition switch “ON”, the cruise control function is deacti- vated and the “CRUISE” indicator light flashes. To reactivate the cruise control function, turn the ignition switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position.

WARNING

Do not use the cruise control under any of the following conditions. This may cause loss of vehicle control: . driving up or down a steep grade . driving on slippery or winding

roads

. driving in heavy traffic

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (247,1)

Starting and operating 7-35

& To set cruise control

2. Depress the accelerator pedal until the vehicle reaches the desired speed.

combination meter will illuminate. The vehicle will maintain the desired speed.

Vehicle speed can be temporarily in- creased while driving with the cruise control activated. Simply depress the accelerator pedal to accelerate the vehi- cle. When the accelerator pedal is re- return to and leased, maintain the previous cruising speed. & To temporarily cancel the

the vehicle will

cruise control

1. Push the “CRUISE” main switch but- ton.

3. Push the “SET/COAST” button and release it. Then release the accelerator pedal.

The cruise control can be temporarily canceled in the following ways:

The “ nation meter will illuminate.

” indicator light on the combi-

At this time, the “

” indicator light on the

. Push the “CANCEL” button. . Depress the brake pedal. . Depress the clutch pedal (MT vehicles

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

7-36 Starting and operating

the selector lever into the “N”

only). . Shift position (AT vehicles only). . Shift the shift lever into neutral position (MT vehicles only). The “ ” indicator light on the combina- tion meter turns off when the cruise control is canceled.

& To turn off the cruise control There are two ways to turn off the cruise control: . Push the “CRUISE” main switch button again. . Turn the ignition switch to the “Acc” or “LOCK” position (but only when the vehicle is completely stopped).

& To change the cruising speed ! To increase the speed (by button)

To resume the cruise control after it has been temporarily canceled and with vehi- cle speed of approximately 20 mph (32
km/h) or more, push the “RES/ACC” button to return to the original cruising speed automatically. The “ ” indicator light on the combina- tion meter will automatically illuminate at this time.

Push the “RES/ACC” button and hold it the vehicle reaches the desired until release the button. The speed. Then, vehicle speed at that moment will be memorized and treated as the new set speed.

Black plate (248,1)

When the difference between the actual vehicle speed and the set speed is less than 4 mph (6.8 km/h), the set speed can be increased 1 mph (1.6 km/h) each time by pressing the “RES/ACC” button quickly. ! To increase the speed (by accel-

erator pedal)

1. Depress the accelerator pedal to accelerate the vehicle to the desired speed. 2. Push the “SET/COAST” button once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accelerator pedal.

NOTE If the difference between the actual vehicle speed when the button is pushed and the speed last time you set is less than 4 mph (6.8 km/h), the vehicle speed will be lowered by 1 mph (1.6 km/h). This occurs because the cruise control system unit regards this operation as that intended to decrease the vehicle speed.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

! To decrease the speed (by button)

Push the “SET/COAST” button and hold it the vehicle reaches the desired until release the button. The speed. Then, vehicle speed at that moment will be memorized and treated as the new set speed.

When the difference between the actual vehicle speed and the set speed is less than 4 mph (6.8 km/h), the set speed can be lowered 1 mph (1.6 km/h) each time by pressing the “SET/COAST” button quickly.

Black plate (249,1)

! To decrease the speed (by brake

pedal)

to release

1. Depress the brake pedal cruise control temporarily. 2. When the speed decreases to the desired speed, press the “SET/COAST” button once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accelerator pedal.

& Cruise control indicator light

Starting and operating 7-37

NOTE . If you press the “CRUISE” main switch button while turning the ignition switch “ON”, the cruise control func- tion is deactivated and the cruise indicator light flashes. To re- control activate the cruise control function, turn the ignition switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position. . If this indicator light and the CHECK ENGINE warning light/malfunction in- dicator lamp flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer.

indicator light

The cruise control illumi- nates when the ignition switch is turned to the “ON” position and turns off after approximately 3 seconds. The light illuminates when the “CRUISE” main switch is pressed.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

7-38 Starting and operating

& Cruise control set indicator

light

indicator

The cruise control set light illuminates when the ignition switch is turned to the “ON” position and turns off after approximately 3 seconds. The light illuminates when vehicle speed has been set.

Black plate (250,1)

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (15,1)

Driving tips

New vehicle break-in driving – the first

8-2
1,000 miles (1,600 km) ..................................... 8-2
Fuel economy hints ............................................ 8-2
Engine exhaust gas (carbon monoxide)............ 8-3
Catalytic converter .............................................. 8-4
Periodic inspections ........................................... 8-4
Driving in foreign countries ............................... 8-5
Driving tips for AWD vehicles ............................ 8-6
On-pavement and off-road driving..................... 8-8
Winter driving ...................................................... 8-8
Operation during cold weather............................. Driving on snowy and icy roads .......................... 8-9
Corrosion protection .......................................... 8-10
Snow tires ......................................................... 8-10
Tire chains......................................................... 8-11

Rocking the vehicle ........................................... Loading your vehicle......................................... Vehicle capacity weight...................................... GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating) ........................ Roof rail (if equipped) ........................................ Trailer hitch (dealer option)............................... Connecting a trailer ........................................... When you do not tow a trailer ............................ Trailer towing ..................................................... Warranties and maintenance .............................. Maximum load limits .......................................... Trailer hitches.................................................... Connecting a trailer ........................................... Trailer towing tips ..............................................

8-11
8-11
8-12

8-13
8-13
8-14
8-14
8-16
8-16
8-16
8-16
8-19
8-20
8-21

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

8-2 Driving tips

New vehicle break-in driving – the first 1,000 miles (1,600
km)

The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): . Do not race the engine. And do not allow engine speed to exceed 4,000 rpm except in an emergency. . Do not drive at one constant engine or vehicle speed for a long time, either fast or slow. . Avoid starting suddenly and rapid acceleration, except in an emergency. . Avoid hard braking, except emergency.

in an

The same break-in procedures should be applied to an overhauled engine, newly mounted engine or when brake pads or brake linings are replaced with new ones.

Fuel economy hints

The following suggestions will help to save fuel. . Select the proper gear position for the speed and road conditions. . Avoid sudden acceleration or decelera- tion. Always accelerate gently until you reach the desired speed. Then try to maintain that speed for as long as possible. . Do not pump the accelerator and avoid racing the engine. . Avoid unnecessary engine idling. . Keep the engine properly tuned. . Keep the tires inflated to the correct pressure shown on the tire placard, which is located under the door latch on the driver’s side. Low pressure will increase tire wear and fuel consumption. . Use the air conditioner only when necessary. . Keep the front and rear wheels in proper alignment. . Avoid carrying unnecessary luggage or cargo.

Black plate (252,1)

Engine exhaust gas (carbon monoxide)

WARNING

. Never inhale engine exhaust gas. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is dan- gerous, or even lethal, if inhaled. . Always properly maintain the en- gine exhaust system to prevent engine exhaust gas from enter- ing the vehicle.

. Never run the engine in a closed space, such as a garage, except for the brief time needed to drive the vehicle in or out of it.

. Avoid remaining in a parked vehicle for a lengthy time while the engine is running. If that is unavoidable, then use the venti- lation fan to force fresh air into the vehicle.

. Always keep the front ventilator inlet grille free from snow, leaves or other obstructions to ensure that the ventilation system al- ways works properly.

. If at any time you suspect that

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

exhaust fumes are entering the vehicle, have the problem checked and corrected as soon as possible. If you must drive under these conditions, drive only with all windows fully open. . Keep the rear gate closed while driving to prevent exhaust gas from entering the vehicle.

NOTE Due to the expansion and contraction of the metals used in the manufacture of the exhaust system, you may hear a crackling sound coming from the ex- haust system for a short time after the engine has been shut off. This sound is normal.

Catalytic converter

Turbo models

Non-turbo models

The catalytic converter is installed in the exhaust system. It serves as a catalyst to

Black plate (253,1)

Driving tips 8-3

reduce HC, CO and NOx in exhaust gases, thus providing cleaner exhaust.

To avoid damage to the catalytic conver- ter: . Use only unleaded fuel. Even a small amount of leaded fuel will damage the catalytic converter. . Never start the engine by pushing or pulling the vehicle. . Avoid racing the engine. . Never turn off the ignition switch while the vehicle is moving. . Keep your engine tuned-up. If you feel the engine running rough (misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. . Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust sys- tem. . Do not drive with an extremely low fuel level.

WARNING

. Avoid fire hazards. Do not drive or park the vehicle anywhere near flammable materials (e.g., grass, paper, rags or leaves), because the catalytic converter

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

8-4 Driving tips

operates at very high tempera- tures.

. Keep everyone and flammable materials away from the exhaust pipe while the engine is running. The exhaust gas is very hot.

Black plate (254,1)

Periodic inspections

Driving in foreign countries

To keep your vehicle in the best condition at all times, always have the recom- mended maintenance services listed in the maintenance schedule in the “War- ranty and Maintenance Booklet” per- formed at the specified time or mileage intervals.

When planning to use your vehicle in another country: . Confirm the availability of the correct requirements” fuel. Refer section in chapter 7. . Comply with all quirements of each country.

regulations and re-

to the “Fuel

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Driving tips for AWD vehicles

All-Wheel Drive distributes the engine power to all four wheels. AWD vehicles provide better traction when driving on slippery, wet or snow-covered roads and when moving out of mud, dirt and sand. By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during acceleration and added engine braking force during deceleration.

Therefore, your SUBARU AWD vehicle may handle differently than an ordinary two wheel drive vehicle and it contains some features unique to AWD. For safety purposes as well as to avoid damaging the AWD system, you should keep the following tips in mind:

. An AWD vehicle is better able to climb steeper roads under snowy or slippery conditions than a two wheel drive vehicle. There is little difference in handling, however, during extremely sharp turns or sudden braking. Therefore, when driving down a slope or turning corners, be sure to reduce your speed and maintain an ample distance from other vehicles. . When replacing a tire, make sure you use only the same size, construction, brand, and load range as the original tires listed on the tire placard. Using other sizes, circumference or construction may result in severe mechanical damage to the drive train of your vehicle and may affect ride, handling, braking, speedometer/od- ometer calibration, and clearance be- tween the body and tires. It also may be dangerous and lead to loss of vehicle control. . If you use a temporary spare tire to replace a flat tire, be sure to use the original temporary spare tire stored in the vehicle. Using other sizes may result in severe mechanical damage to the drive train of your vehicle. . Always check the cold tire pressure before starting to drive. The recom- mended tire pressure is provided on the tire placard, which is located under the door latch on the driver’s side.

Black plate (255,1)

Driving tips 8-5

. Tire chains should always be placed on the front wheels only. . There are some precautions that you must observe when towing your vehicle. For detail information, refer to the “Towing” section in chapter 9.

WARNING

. Always maintain a safe driving speed according to the road and weather conditions in order to avoid having an accident on a sharp turn, during sudden brak- ing or under other similar condi- tions.

. Always use the utmost care in driving – overconfidence be- cause you are driving an All- Wheel Drive vehicle could easily lead to a serious accident.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (256,1)

8-6 Driving tips

On-pavement and off-road driving

WARNING

. In a rollover crash, an unbelted person is significantly more likely to die than a person wear- ing a seat belt. You the driver and all your passengers should fas- ten the seatbelts before starting to drive in order to minimize the chance of serious injury or death. . Do not make sharp turns and quick maneuvers unless abso- lutely unavoidable. Such actions are dangerous as you may lose control, possibly resulting in a rollover which could cause death or serious injury.

. Always maintain a safe driving speed according to the road and weather conditions in order to avoid having an accident on a sharp turn, during sudden brak- ing or under other similar condi- tions.

. Whenever strong crosswinds are present, slow down sufficiently to maintain control of your vehi- cle. Remember that your vehicle,

with its higher profile and center of gravity, is more likely to be affected by crosswinds than or- dinary passenger cars.

. Always use the utmost care in driving – overconfidence be- cause you are driving an All- Wheel Drive vehicle could easily lead to a serious accident.

Your vehicle is classified as a utility vehicle. Utility vehicles feature a higher ground clearance which enables them to be used for wide applications including off- road driving. But please keep in mind that your vehicle is neither a conventional off- road vehicle nor an all-terrain vehicle. A higher center of gravity in relation to the tread width as compared with ordinary passenger cars makes vehicles of this type more likely to roll over. In reality, utility vehicles have a significantly higher roll- over rate than other types of vehicles. The high ground clearance of this vehicle is a real advantage, giving you a better view of the road and allowing you to anticipate problems earlier. However, remember that your utility vehicle is not designed for high- speed cornering comparable to ordinary passenger cars and that your vehicle could roll over if you make a sharp turn at high speed. If you do take your

SUBARU off-road, certain common sense precautions such as the following should be taken: . Make certain that you and all of your passengers are wearing seatbelts. . Carry some emergency equipment, such as a towing rope or chain, a shovel, wheel blocks, first aid kit and cell phone or citizens band radio. . Drive carefully. Do not take unneces- sary risks by driving in dangerous areas or over rough terrain. . Slow down and employ extra caution at all times. When driving off-road, you will not have the benefit of marked traffic lanes, banked curves, traffic signs and the like. . Do not drive across steep slopes. Instead, drive either straight up or straight down the slopes. A vehicle can much more easily tip over sideways than it can end over end. Avoid driving straight up or down slopes that are too steep. . Avoid sharp turning maneuvers, espe- cially at higher speeds. . Do not grip the inside or spokes of the steering wheel. A bad bump could jerk the wheel and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim. . If driving through water, such as when

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

crossing shallow streams, first check the depth of the water and the bottom of the stream bed for firmness and ensure that the bed of the stream is flat. Drive slowly and completely through the stream. The water should be shallow enough that it does not reach the vehicle’s undercar- riage. Water entering the engine air intake or the exhaust pipe or water splashing onto electrical parts may damage your vehicle and may cause it to stall. Never attempt to drive through rushing water; regardless of its depth, it can wash away the ground from under your tires, resulting in possible loss of traction and even vehicle rollover. . Always check your brakes for effec- tiveness immediately after driving in sand, mud or water. Do this by driving slowly and stepping on the brake pedal. Repeat that process several times to dry out the brake discs and brake pads. . Do not drive or park over or near flammable materials such as dry grass or fallen leaves, as they may burn easily. The exhaust system is very hot while the engine is running and right after engine stops. This could create a fire hazard. . After driving through tall grass, mud, rocks, sand, rivers, etc., check that there is no grass, bush, paper, rags, stones, sand, etc. adhering to or trapped on the

it

underbody. Clear off any such matter from the underbody. If the vehicle is used with these materials trapped or adhering to the underbody, a mechanical breakdown or fire could occur. . Secure all cargo carried inside the vehicle and make certain that is not piled higher than the seatbacks. During sudden stops or jolts, unsecured cargo could be thrown around in the vehicle and cause injury. Do not pile heavy loads on the roof. Those loads raise the vehicle’s center of gravity and make it more prone to tip over. . If you must rock the vehicle to free it from sand or mud, depress the accelerator pedal slightly and move the selector lever back and forth between “D” and “R” repeatedly. Do not race the engine. For the best possible traction, avoid spinning the wheels when trying to free the vehicle. . When the road surface is extremely slippery, you can obtain better traction by starting the vehicle with the transmission in 2nd than 1st. . Never equip your vehicle with tires larger than those specified in this manual. . Wash the vehicle’s underbody after off- road driving. Suspension components are particularly prone to dirt buildup, so they need to be washed thoroughly. . Frequent driving of an AWD vehicle

Black plate (257,1)

Driving tips 8-7

under hard-driving conditions such as rough roads or off roads will necessitate more frequent replacement of engine oil, brake fluid and transmission oil than that specified in the maintenance schedule described in the “Warranty and Mainte- nance Booklet”.

Remember that damage done to your SUBARU while operating it off-road and not using common sense precautions such as those listed above is not eligible for warranty coverage.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (258,1)

8-8 Driving tips

Winter driving

& Operation during cold

weather

Carry some emergency equipment, such as tire chains, a window scraper, a bag of sand, flares, a small shovel, and jumper cables.

Check the battery and cables. Cold temperatures reduce battery capacity. The battery must be in good condition to provide enough power for cold winter starts.

Use an engine oil of proper grade and viscosity for cold weather. Heavy summer oil will cause harder starting. Keep the door

locks from freezing by

squirting them with deicer or glycerin.

Forcing a frozen door open may damage or separate the rubber weather strips around the door. the door is frozen, use hot water to melt the ice, and after- wards thoroughly wipe the water away.

If

Use a windshield washer fluid that con- tains an antifreeze solution. Do not use engine antifreeze or other substitutes because they may damage the paint of the vehicle. SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.

Washer Fluid Con-

centration

Freezing Temperature

30%

50%

100%

10.48F (−128C) −48F (−208C) −498F (−458C)

In order to prevent freezing of washer fluid, check the freezing temperatures in the table above when adjusting the fluid concentration to the outside temperature. If you fill the reservoir tank with a fluid with a different concentration from the one

used previously, purge the old fluid from the piping between the reservoir tank and washer nozzles by operating the washer for a certain period of time. Otherwise, if the concentration of the fluid remaining in the piping is too low for the outside temperature, it may freeze and block the nozzles.

CAUTION

Adjust the washer fluid concentra- tion appropriately for the outside temperature. If the concentration is inappropriate, sprayed washer fluid may freeze on the windshield and obstruct your view, and the fluid may freeze in the reservoir tank.

! Before driving your vehicle Before entering the vehicle, remove any snow or ice from your shoes because that could make the pedals slippery and dangerous.

While warming up the vehicle before driving, check that the accelerator pedal, brake pedal, and all other controls operate smoothly.

Clear away ice and snow that has accumulated under the fenders to avoid making steering difficult. During severe

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

winter driving, stop when and where it is safe to do so and check under the fenders periodically. ! Parking in cold weather Do not use the parking brake when parking for long periods in cold weather since it could freeze in that position. Instead, observe the following. 1. Place the shift lever in “1” or “R” for manual transmission vehicles, and in “P” for automatic transmission vehicles. 2. Use tire stops under prevent the vehicle from moving.

the tires to

When the vehicle is parked in snow or when it snows, raise the wiper blades off the glass to prevent damage to them.

When the vehicle has been left parked after use on roads heavily covered with snow, or has been left parked during a snowstorm, icing may develop on the brake system, which could cause poor braking action. Check for snow or ice buildup on the suspension, disc brakes and brake hoses underneath the vehicle. If there is caked snow or ice, remove it, being careful not to damage the disc brakes and brake hoses and ABS har- ness.

WARNING

Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle if you park the vehicle in snow with the engine running.

! Refueling in cold weather To help prevent moisture from forming in the fuel system and the risk of its freezing, use of an antifreeze additive in the fuel tank is recommended during cold weather. Use only additives that are specifically designed for this purpose. When an antifreeze additive is used, its effect lasts longer if the tank is refilled whenever the fuel level reaches half empty.

If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity. & Driving on snowy and icy

roads

To prevent skidding and slipping, avoid sudden braking, abrupt acceleration, high- speed driving, and sharp turning when driving on snowy or icy roads. Always maintain ample distance between your vehicle and the vehicle ahead of you

Black plate (259,1)

Driving tips 8-9

the foot brake, use the the into a lower gear

to avoid the need for sudden braking. To supplement engine brake effectively to control vehicle speed. (Shift when necessary.) Avoid shifting down abruptly. Such beha- vior can cause the wheels to lock, possibly leading to loss of vehicle control.

An anti-lock brake system (ABS) en- hances your vehicle’s braking perfor- mance on snowy and icy roads. For information on braking on slippery sur- faces, refer to the “ABS (Anti-lock Brake System)” and “Vehicle Dynamics Control system” sections in chapter 7.

WARNING

Do not use the cruise control on slippery roads such as snowy or icy roads. This may cause loss of vehicle control.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

8-10 Driving tips

CAUTION

Avoid prolonged continuous driving in snowstorms. Snow will enter the engine’s intake system and may hinder the air flow, which could result in engine shutdown or even breakdown.

If

! Wiper operation when snowing Before driving in cold weather, make sure frozen to the the wiper blades are not windshield or rear window. the wiper blades are frozen to the windshield or rear window, use the defroster with the airflow ” position and the control dial temperature control dial set for maximum warmth until the wiper blades are com- pletely thawed out. If your vehicle is equipped with a wiper deicer, it is helpful to thaw the windshield wiper blades. To thaw out the rear wiper blade, use the rear window defogger.

in the “

When driving in snow, if frozen snow starts to stick on the surface of the windshield despite wiper operation, use the defroster with the airflow control dial in “ ” and the temperature control dial set for maximum warmth. After the windshield gets warmed enough to melt the frozen snow on it, wash it away using the windshield washer.

Black plate (260,1)

Snow stuck on the wiper arm prevents the wiper from working effectively. If snow is stuck on the wiper arm, pull off the road to a safe place, then remove it. If you stop the vehicle at road side, use the hazard warning flasher to alert other drivers.

We recommend use of non-freezing type wiper blades (winter blades) during the seasons you could have snow and sub- zero temperatures. Blades of this type give superior wiping performance in snowy conditions. Be sure to use blades that are suitable for your vehicle.

CAUTION

During high-speed driving, non- freezing type wiper blades may not perform as well as standard wiper blades. If this happens, reduce the vehicle speed.

NOTE When the season requiring non-freez- ing type wiper blades is over, replace them with standard wiper blades.

& Corrosion protection Refer to the “Corrosion protection” section in chapter 10.

& Snow tires

WARNING

. When replacing original tires with winter (snow) tires, make sure you use only the same size, construction and load range as the original tires listed on the tire placard. Using other sizes and construction may affect speed- ometer/odometer calibration and clearance between the body and tires. It also may be dangerous and lead to loss of vehicle con- trol.

. You must install four winter tires that are of the same size, con- struction, brand, and load range. Mixing other sizes or construc- tions may result in severe me- chanical damage to the drive train of your vehicle and may affect ride, handling, braking and speedometer/odometer calibra- tion. It also may be dangerous and lead to loss of vehicle con- trol.

. Do not use a combination of radial, belted bias or bias tires since it may cause dangerous