Download PDF Manual


Keys and doors


B1


B2


HS2016BB


A: “LOCK/ARM” button (Orange)


Press to lock all doors. Press and Hold to activate panic alarm. Press three times in a five second period to use vehi- cle finder function.


B: “UNLOCK/DISARM” button (Blue)


1) Press once to Unlock driver’s door. 2) Press a second time to Unlock all other doors.


C: LED


(cid:132) Locking the doors Briefly press the “LOCK/ARM” button (for less than two seconds) to lock all doors. An electronic chirp will sound once and the turn signal lights will flash once.


2-8


If any of the doors is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors are not prop- erly closed. When you close the door, it will automati- cally lock. NOTE If the “LOCK/ALARM” button is pressed for two seconds or longer, the panic alarm will sound. When locking the doors in normal circumstances, press the “LOCK/ALARM” button for less than two seconds. For details on the panic alarm, refer to “Sounding a panic alarm”.


(cid:132) Unlocking the doors Briefly press the “UNLOCK/DISARM” button (for less than two seconds) to unlock the driver’s door. An elec- tronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors, briefly press the “UNLOCK/DISARM” button a second time within 5
seconds. NOTE If the interval between the first and second press- es of the “UNLOCK/DISARM” button (for unlock- ing of all of the doors) is extremely short, the sys- tem may not respond.


(cid:132) Illuminated entry The interior (dome) light will illuminate when the “UN- LOCK/DISARM” button is pressed. These lights stay illuminated for approximately 30 seconds if any of the doors is not opened. If the “LOCK/ARM” button is pressed before 30 sec- onds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light switch must be set to the mid- dle position in order for this function to operate.


(cid:132) Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “LOCK/ARM” button three times in a five-second peri- od will cause your vehicle’s horn to sound once and its turn signal lights to flash three times.


(cid:132) Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the re- mote is pressed, the alarm will be deactivated after ap-


Keys and doors


proximately 30 seconds.


(cid:132) Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If de- sired, you may turn the audible signal off. To turn the audible signal off, unlock the doors by pushing “UNLOCK/DISARM” button and then simulta- neously depress “LOCK/ARM” and “UNLOCK/DIS- ARM” buttons for more than two seconds. An electron- ic chirp will sound twice and the turn signal lights will flash twice to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the doors by pushing “UNLOCK/DISARM” button and then simulta- neously depress “LOCK/ARM” and “UNLOCK/DIS- ARM” buttons for more than two seconds. An electron- ic chirp will sound once and the turn signal lights will flash once to inform you that the audible signal has been turned on.


– CONTINUED – 2-9


Keys and doors


(cid:132) Replacing the battery


Do not let dust, oil or water get on or in the transmitter when replacing the battery.


When the transmitter battery begins to get weak, transmitter range will begin to decrease and the LED will not illuminate. Replace the battery as soon as pos- sible. To replace the battery:


1. Remove the two screws on the back of the trans-


HS2017BA


2-10


mitter case by using a Phillips screwdriver. 2. Separate the case. 3. Remove the old battery from the holder.


HS2018BB


1) Positive (+) side facing up 4. Replace with a new battery (Type CR2032 or equivalent) making sure to install the new battery with the positive (+) side facing up. 5. Install the back half of the transmitter case. 6. Reinstall the two screws on the back of the trans- mitter case. After the battery is replaced, the transmitter must be synchronized with the keyless entry system’s control unit. Press either the “LOCK/ARM” or “UN-


LOCK/DISARM” button six times to synchronize the unit.


(cid:132) Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system. (cid:84) Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmit- ter codes. The four transmitter codes may be the same or different.


Keys and doors


To enter the programming mode:


1. Press “UNLOCK/DISARM” button to disarm the se- curity system. (if your vehicle is equipped with the op- tional security system.)


HS2016CA


– CONTINUED – 2-11


Keys and doors


HS2019BD


HS2020BB


2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.


1) ON 2) LOCK 4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15
seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode. NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this proce- dures.


2-12


To program the transmitters:


1. Open the driver’s door. 2. Close the driver’s door.


HS2019BE


Keys and doors


HS2016DB


1) Press any button. 3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound twice to indicate that the transmitter has been programmed. Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter. To exit the programming mode: 1. After all of your transmitters are programmed, re- move the key from the ignition switch. The horn will sound three times to indicate that the – CONTINUED – 2-13


to your vehicle.


Keys and doors


system has exited the programming mode. 2. Make sure that the keyless entry system properly operates by operating each transmitter. (cid:84) Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code re- mains in the memory. For security reasons, lost trans- mitter codes should be deleted from the memory. To delete old transmitter codes, program four trans- mitter codes into the system. If you have only one cur- rent transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memo- ry. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access


2-14


Security system (if equipped) The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key. The system can be armed and disarmed with the re- mote transmitter. The system does not operate when the key is inserted into the ignition switch.


(cid:132) System operation The security system will give the following alarm indi- cations when triggered: (cid:121) The turn signal lights will flash and the horn will sound intermittently. In addition, the starter motor will not operate. (cid:121) The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tam- pered with again. The alarm will continue for six times if any sensor continues to be activated. The alarm is triggered by: (cid:121) Opening a door. (cid:121) Application of physical shock to the vehicle (e.g.


Keys and doors


breaking glass or forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher levels of shock are detected and the system will go into full alarm. (cid:121) Ignition switch being turned on while in armed state. NOTE (cid:121) The alarm will not be triggered by opening the switchback door. (cid:121) The alarm may not be triggered when the win- dow is broken with a sharp-edged tool. (cid:121) With the valet mode selected, the security sys- tem does not operate and the turn signal lights do not flash when the remote transmitter is used for locking and unlocking. The security system indicator light in the combi- nation meter flashes twice per second to show that the valet mode is selected. For details, refer to “Valet mode” in this section.


(cid:132) Arming the system (cid:84) To arm the system using remote transmitter 1. Close all windows and moonroof.


– CONTINUED – 2-15


Keys and doors


2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close all doors.


1) Press to Arm the system. 2) Press to Disarm the system.


HS2016EB


2-16


UB2033BB


1) Security system indicator light 6. Briefly press the “LOCK/ARM” button (for less than two seconds). All doors will lock, an electronic chirp will sound once, the turn signal lights will flash once and the indicator light starts flashing slowly (approxi- mately once every two seconds). If any of the doors (except the switchback door) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors are not properly closed. When you close the door, the system will automatically arm and doors will automatically lock.


(cid:84) To arm the system using power door locking


switches


1. Close all windows and moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close the doors but leave only the driver’s door or the front passenger’s door open.


UB2024CC


6. Push the power door locking switch forward (“LOCK” side) to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the indicator light will start flashing slowly (approximately once ev-


Keys and doors


ery two seconds) to inform you that the system has armed. NOTE The system can be armed even if the engine hood, the windows, the switchback door and/or moon- roof are open. Always make sure that they are fully closed before arming the system.


(cid:132) Disarming the system Briefly press the “UNLOCK/DISARM” button (for less than two seconds) on the remote transmitter. The driv- er’s door will unlock, an electronic chirp will sound twice, the turn signal lights will flash twice and the in- dicator light will go off. To unlock all other doors, briefly press the “UNLOCK/ DISARM” button a second time. (cid:84) Emergency disarming If you cannot disarm the system using the transmitter (i.e. the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system with- out using the transmitter. To disarm the system: 1. Unlock the door with the key and then open the door.


– CONTINUED – 2-17


Keys and doors


2. The alarm will sound. 3. Insert the key into the ignition switch and cycle it from “LOCK” to “ON” three (3) times within 5 sec- onds.


(cid:132) Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30 seconds.


(cid:132) Valet mode When you choose the valet mode, the security system does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors and panic activation. To enter the valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button depressed for more than two seconds. The security system indica- tor light will continue to flash 2 times per second indi- cating that the system is in the valet mode. To exit valet mode, open the driver’s door and keep


2-18


the “UNLOCK/DISARM” button pressed for more than two seconds. The indicator will stop flashing.


(cid:132) Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically ac- complished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. (cid:84) To enter the passive mode Since programming the passive arming mode is a complicated procedure, have it done by your nearest SUBARU dealer. (cid:84) Arming the system


In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4 be- low or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.


1. Turn the ignition switch to “ON”.


HS2024BC


1) ON 2) LOCK 2. Turn the ignition switch from “ON” to “LOCK” and remove the key from the ignition switch.


Keys and doors


UB2024DC


3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the in- side door lock levers. 5. Close the doors. The system will automatically arm after one minute. In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arming will take place immediately regardless of whether or not the passive mode has been selected. (cid:84) Disarming the system To disarm the system, briefly press the “UNLOCK/ – CONTINUED – 2-19


switch to “ON”.


Keys and doors


DISARM” button on the transmitter. (cid:84) Tripped sensor identification If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the sys- tem, this indicates that the alarm was triggered. The number of times the indicator light flashes indicates what sensor caused the alarm condition. To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to “ON” twice. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing. The indicator light provides the following indications. Flashing once: Any door has been opened. Flashing three times: The impact sensor in the sys- tem’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected. NOTE The battery must be reconnected before the indi- cator light will flash. To exit this mode, close the door and turn the ignition


2-20


Child safety locks


Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.


Keys and doors


the doors from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.


1) Lock 2) Unlock Each rear door has a child safety lock that prevents


UB2002BB


– CONTINUED – 2-21


Keys and doors


Windows (cid:132) Power windows


To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window. (cid:121) Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.


The power windows operate only when the ignition switch is in the “ON” position.


2-22


(cid:84) Driver’s side switches


UB2008BB


1) Lock switch 2) For driver’s window 3) For rear left passenger’s window 4) For front passenger’s window 5) For rear right passenger’s window All door windows can be controlled by the power win- dow switch cluster at the driver side door.


(cid:86) Operating the driver’s window


UB2008DB


1) Lock 2) Unlock 3) Close 4) Open 5) Automatically open To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without hold- ing the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window half-


Keys and doors


way, pull the switch up lightly. To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows To open the passengers’ windows, push the appropri- ate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired posi- tion. (cid:86) Locking the passengers’ windows To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.


– CONTINUED – 2-23


Keys and doors


(cid:84) Passengers’ side switches


Front passenger’s window switch 1) Open 2) Close


2-24


UB2009CB


UB2005BB


Rear passenger’s window switches 1) Open 2) Close To open the window, push the switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.


Tailgate


Keep the tailgate closed when the vehicle is moving. If you must drive with the tailgate open, use the optional SUBARU Bed Extender and place the License Plate Bracket at its fully lowered/open position. Cargo must not stick out beyond the Extender. Otherwise a danger- ous road hazard or personal injury could result.


Keys and doors


upper surface of the rear bumper to avoid damaging the tailgate. To open the tailgate, lift up on its handle while pulling the tailgate toward you. The support cables hold the tailgate open. See “Loading your vehicle” section in Chapter 8 for precautions in loading cargo. To close the tailgate, firmly push it upward until it latch- es. After you put the tailgate back up, pull it back toward you to be sure it latches securely.


Before opening the tailgate, remove any object on the


UB2050BA


– CONTINUED – 2-25


Keys and doors


(cid:132) License plate bracket


UB2051BA


When you drive with the tailgate open and with the bed extender used, the license plate bracket must be placed at its fully lowered/open position to make the rear license plate visible.


In order to avoid damaging the license plate bracket or the bumper, the license plate bracket must be in its fully lowered/open position be- fore the tailgate is lowered.


2-26


UBB096BA


To use the license plate bracket at its lowered/open


UB2053BA


position, push the two release buttons and pull the li- cense plate bracket up until it clicks. And then open the tailgate. If your vehicle is equipped with a trailer hitch, remove the ball mount from the hitch receiver tube before opening the tailgate. Failure to follow this procedure could result in damage to the license plate bracket. When you drive with the tailgate closed, the license plate bracket must be restored to its original position. To restore the license plate bracket to its original posi- tion, close the tailgate, and then pull the license plate bracket down until it clicks. If the license plate bracket is hard to be restored to its original position, mud may have accumulated on the back of the license plate bracket. Remove accumulat- ed mud before pulling the license bracket down.


Keys and doors


Switchback door


With the switchback door open, you can increase the usable cargo space and can carry long objects.


UB2052BA


In order to avoid damaging the license plate bracket or the bumper, the license plate bracket must be restored to its original position until it clicks.


Secure long objects properly to prevent them from sliding forward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equivalent.


– CONTINUED – 2-27


Keys and doors


Pay attention that your fingers do not get pinched with the switchback door when open- ing and closing it.


To open the switchback door:


1. Pull up the rear seat cushion. Refer to “Rear seats” section in Chapter 1 for operating details.


UB1172BA


2-28


UB1112CB


1) Red A) LOCK B) UNLOCK


Keys and doors


UB1113BA


UB1114BA


2. Unlock the rear seatback by pulling up on the knob and fold down the rear seatback. Confirm that the pins located at the bottom of the seat cushion is inserted into the slots at the top of the seatback.


3. Fold down the switchback door by releasing the – CONTINUED – 2-29


UB1115BA


the vehicle body that prevent the door from ful- ly closing or that crimp the weather strip around the door.


To close the switchback door, firmly push it upward until it latches. Return the seatback and seat cushion to their original positions and make sure they are securely locked.


After returning the seatback to its original posi- tion, make sure that the rear seatback has been securely locked. When securely locked, the red marks on the locking knobs are no longer visi- ble.


Keys and doors


lock knob. Then you can have a flat and larger cargo space. 4. Place the long object on the cargo bed through the switchback door opening. Be sure all items are secured in place. NOTE (cid:121) When opening the switchback door in snow, ac- cumulated snow in the cargo bed may enter the passenger compartment which could result in dampness in the passenger compartment. Prior to opening of the switchback door, brush off the snow completely. (cid:121) Close the switchback door whenever you leave the vehicle to prevent unauthorized entry.


The switchback door should be kept complete- ly shut when the vehicle is idling in an enclosed or partially enclosed area to avoid the possibil- ity of exhaust gas entering the passenger com- partment. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is extremely dangerous, or even lethal if in- haled. To ensure that exhaust gas cannot pen- etrate the switchback door, make certain that there are no obstructions between the door and


2-30


(cid:132) Switchback door indicator light


Moonroof (if equipped)


Keys and doors


UB7023EA


While the ignition switch is in the “ON” position, the switchback door indicator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” po- sition, the switchback door indicator light flashes for about 20 seconds and goes off when the switchback door is open.


Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident. To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) Before closing the moonroof, make sure that no one’s hands, arms, neck, head or other ob- jects will be accidentally caught in the moon- roof. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.


(cid:121) Do not sit on the edge of the open moonroof.


– CONTINUED – 2-31


Keys and doors


(cid:121) Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.


(cid:132) Tilting/sliding moonroof The moonroof has both tilting and sliding functions. The moonroof operates only when the ignition switch is in the “ON” position.


UB2034BB


1) Open/Close switch 2) Tilt switch (cid:84) To raise or lower the moonroof The tilting function will only operate when the moon-


2-32


roof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause damage to the moon- roof. (cid:84) To open or close the moonroof Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you con- tinue to press on the switch. Release the switch once and push it again to close the moonroof completely. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to pre- vent water drops from falling into the passenger com- partment. NOTE If the moonroof cannot be closed through the switch operation because of system failure, it can


be closed manually using a hex-headed wrench. For the procedure, refer to “Moonroof – if the moonroof cannot be closed” in Chapter 9 “In case of emergency”.


(cid:132) Sun shade


UG2510BA


The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.


Keys and doors


– CONTINUED – 2-33


Ignition switch .............................................. LOCK .................................................................. ACC .................................................................... ON ....................................................................... START ................................................................ Key reminder chime .......................................... Ignition switch light (if equipped) .................... Key interlock release (AT vehicles) ................. Hazard warning flasher ................................ Meters and gauges ....................................... Speedometer ..................................................... Odometer/Trip meter ........................................ Tachometer ........................................................ Outside temperature indicator (if equipped) .. Fuel gauge ......................................................... Temperature gauge ........................................... Warning and indicator lights ....................... Seatbelt warning light and chime .................... SRS airbag system warning light .................... CHECK ENGINE warning light/Malfunction indicator lamp ................................................. Charge warning light ........................................ Oil pressure warning light ................................ AT OIL TEMPerature warning light (AT vehicles) ................................................... ABS warning light ............................................. Brake system warning light ............................. Door ajar warning lights ................................... Switchback door indicator light ...................... Low fuel warning light ...................................... All-Wheel Drive warning light (AT vehicles) ...


3-2
3-2
3-3
3-3
3-4
3-4
3-4
3-4
3-5
3-6
3-6
3-6
3-7
3-7
3-8
3-8
3-9
3-9
3-10
3-10
3-11
3-12
3-12
3-12
3-13
3-14
3-14
3-14
3-14


Instruments and controls


Headlights ......................................................... High/low beam change (dimmer) .................... Headlight flasher ............................................... Daytime running light system .........................


Security system status indicator light (if equipped) .................................................... Selector lever position indicator (AT vehicles) ................................................... Gear position indicator (Turbo-AT vehicles) .. Turn signal indicator lights .............................. High beam indicator light ................................. Cargo lamp indicator light ............................... Cruise control set indicator light ....................


3-15
3-15
3-16
3-16
3-16
3-16
3-16
Clock .............................................................. 3-17
Light control switch ...................................... 3-18
3-18
3-19
3-19
3-20
Turn signal lever ........................................... 3-20
Illumination brightness control ................... 3-21
Parking light switch ...................................... 3-22
Fog light button ............................................. 3-23
Wiper and washer ......................................... 3-23
3-25
Rear window defogger button ..................... 3-26
Windshield wiper deicer (if equipped) ........ 3-27
Mirrors ............................................................ 3-28
3-28
3-30
Tilt steering wheel ......................................... 3-33
Horn ................................................................ 3-34


Inside mirror ...................................................... Outside mirrors .................................................


Windshield wiper and washer switches .........


3-1


Instruments and controls


Instruments and controls


Ignition switch


Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.


The ignition switch has four positions: LOCK, ACC, ON and START.


UB4000CA


3-2


NOTE (cid:121) Keep the ignition switch in the “LOCK” position when the engine is not running. (cid:121) Using electrical accessories for a long time with the ignition switch in the “ON” or “ACC” position can cause the battery to go dead. If the ignition switch will not move from the “LOCK” position to the “ACC” position, turn the steering wheel slightly to the left and right as you turn the ignition switch. (cid:121) If the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch. Also, if a large key- holder is attached to the key, your knees or hands may accidentally touch it in a way that turns the ig- nition switch.


(cid:132) LOCK The key can only be inserted or removed in this posi- tion. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.


(cid:84) Automatic transmission vehicles


Instruments and controls


The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. (cid:84) Manual transmission vehicles


HS3015BA


HS2020CA


HS2020DA


The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.


(cid:132) ACC In this position the electrical accessories (radio, ciga- rette lighter socket, etc.) can be used.


(cid:132) ON This is the normal operating position after the engine – CONTINUED – 3-3


Instruments and controls


is started.


(cid:132) START


Do not turn the ignition switch to the “START” position while the engine is running.


The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.


(cid:132) Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ig- nition switch.


(cid:132) Ignition switch light (if equipped) For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened. The light remains on for 10 seconds and goes out after driver’s door is closed or if the key is turned


3-4


to the “ON” position.


(cid:132) Key interlock release (AT vehicles) If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.


2. Remove the cover under the steering column using a Phillips screwdriver.


HS3016BA


UG3025BA


3. Turn the ignition key while pressing the key inter- lock release lever. Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired.


Instruments and controls


Hazard warning flasher


UB8002BA


The hazard warning flasher is used to warn other driv- ers when you have to park your vehicle under emer- gency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the haz- ard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.


– CONTINUED – 3-5


Instruments and controls


Meters and gauges (cid:132) Speedometer The speedometer shows the vehicle speed.


(cid:132) Odometer/Trip meter


To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.


UB3026BB


1) Trip meter 2) Odometer (cid:84) Odometer The odometer shows the total distance that the vehicle has been driven.


3-6


(cid:84) Double trip meter


UB3027BB


1) A trip meter 2) B trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.


A trip meter To set the trip meter to zero, select either the A trip or B trip meter and push the knob and keep it pushed for


B trip meter


Instruments and controls


more than 1 second. NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.


(cid:132) Tachometer


Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.


The tachometer shows the engine speed in thousands of revolutions per minute.


(cid:132) Outside temperature indicator (if


equipped)


The outside temperature indicator shows the outside – CONTINUED – 3-7


Instruments and controls


temperature in a range from –22 to 122°F (–30 to 50°C). The indicator can give a false reading under any of the following conditions: (cid:121) When there is too much sun. (cid:121) During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately follow- ing a shutdown. (cid:121) When the actual outside temperature falls outside the specified indicator range.


(cid:132) Fuel gauge The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ig- nition switch is in the “ACC” or “LOCK” position. The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.


(cid:132) Temperature gauge


If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possi-


3-8


ble. See “In case of emergency” in chapter 9.


UB2012BB


1) Normal operating range The temperature gauge shows engine coolant temper- ature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with


the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.


Instruments and controls


Warning and indicator lights Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:


Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light / Malfunction indica- tor lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light All-Wheel Drive warning light (AT vehicles)


If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair.


(cid:132) Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the remind-


– CONTINUED – 3-9


Instruments and controls


er chime will sound for about six seconds to remind the driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off auto- matically after six seconds.


(cid:132) SRS airbag system warning


light


If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly re- paired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of inju- ry. (cid:121) Flashing or flickering of the indicator light. (cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” posi- tion.


3-10


(cid:121) Continuous illumination of the warning light. (cid:121) Illumination of the warning light while driv- ing.


When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS frontal airbag and seatbelt pretensioners are in normal operation.


(cid:132) CHECK ENGINE warning light/


Malfunction indicator lamp


If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.


If this light comes on steadily or blinks while the engine


is running, it may indicate that there is a problem or po- tential problem somewhere in the emission control system. (cid:84) If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control sys- tem malfunction has been detected. You should have your vehicle checked by an autho- rized SUBARU dealer immediately. NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indica- tor lamp coming on could be a loose or missing fuel fill- er cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK EN- GINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer im- mediately. (cid:84) If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the


Instruments and controls


emission control system. To prevent serious damage to the emission control system, you should do the following: (cid:121) Reduce vehicle speed. (cid:121) Avoid hard acceleration. (cid:121) Avoid steep uphill grades. (cid:121) Reduce the amount of cargo, if possible. (cid:121) Stop towing a trailer as soon as possible. The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.


(cid:132) Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU deal- er immediately.


– CONTINUED – 3-11


Instruments and controls


(cid:132) Oil pressure warning light


Do not operate the engine with the oil pressure warning light on. This may cause serious en- gine damage.


If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil lev- el is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.


(cid:132) AT OIL TEMPerature warning


light (AT vehicles)


The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid tem- perature is too hot.


3-12


If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. (cid:84) Automatic transmission control system warn-


ing


If the light flashes after the engine starts, it may indi- cate that the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.


(U.S.) (cid:132) ABS warning light (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.


If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. (cid:121) The warning light does not come on when the ignition switch is turned to the “ON” position.


(cid:121) The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). (cid:121) The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.


NOTE If the warning light behavior is as described be- low, the ABS system may be considered normal. (cid:121) The warning light comes on right after the en- gine is started but goes out immediately, remain- ing off. (cid:121) The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12 km/h). (cid:121) The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery volt- age and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.


Instruments and controls


(cid:132) Brake system warning light


(U.S.) (Canada)


(cid:121) Driving with the brake system warning light on is dangerous. This indicates your brake sys- tem may not be working properly. If the light re- mains on, have the brakes inspected by a SUBARU dealer immediately. (cid:121) If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.


This light has the following two functions: (cid:84) Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. (cid:84) Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid res- ervoir with the ignition switch in the “ON” position and with the parking brake fully released.


– CONTINUED – 3-13


Instruments and controls


If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the near- est safe place and check the brake fluid level. If the flu- id level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the near- est SUBARU dealer for repair.


(cid:132) Door ajar warning lights The specific door ajar warning light comes on if any door is not fully closed. Always make sure this light is out before you start to drive.


(cid:132) Switchback door indicator light While the ignition switch is in the “ON” position, the switchback door indicator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” po- sition, the switchback door indicator light flashes for about 20 seconds and goes off when the switchback door is open.


3-14


(cid:132) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.6 US gal (10.0 liters, or 2.2 Imp gal). It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 3.7 US gal (14 liters, 3.1 Imp gal).


Promptly put fuel in the tank whenever the low fuel warning light comes on. If the engine mis- fired as a result of an empty tank, resulting cat- alyzer damage could cause damage to the tur- bocharger.


(cid:132) All-Wheel Drive warning light


(AT vehicles)


The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds.


(cid:84) Turbo models This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires. (cid:84) Non-turbo models This light comes on when All-Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes. This light flashes if the vehicle is driven with tires of dif- ferent diameters or with the air pressure excessively low in any of its tires.


Continued driving with the AWD warning light flashing can lead to powertrain damage. If the AWD warning light flashes, promptly park in a safe place then check whether all four tires are the same diameter and whether any of the tires has a puncture or has lost air pressure for some other reason.


Instruments and controls


(cid:132) Security system status indicator


light (if equipped)


This light is found at the bottom center of the combina- tion meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, refer to the “Security system (if equipped)” in Chapter 2.


(cid:132) Selector lever position indicator (AT


vehicles)


This indicator shows the position of the selector lever.


UB3025AA


– CONTINUED – 3-15


Instruments and controls


(cid:132) Gear position indicator (Turbo-AT ve-


hicles)


UBS094AA


When the selector lever is in the manual gate, this in- dicator shows the currently selected gear.


(cid:132) Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.


3-16


(cid:132) High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.


(cid:132) Cargo lamp indicator light


Do not switch on the cargo lamp while driving to avoid distracting other drivers.


This indicator light shows that the cargo lamp comes on.


(cid:132) Cruise control set indicator light (cid:84) Non-turbo models The light comes on when vehicle speed has been set. (cid:84) Turbo models The cruise set indicator light comes on when the igni- tion switch is turned to the “ON” position and goes out after about three seconds. The light comes on when vehicle speed has been set.


Instruments and controls


Clock


NOTE (cid:121) If you move the cruise control lever while turn- ing the ignition switch “ON”, the cruise control function is deactivated and the cruise control set indicator light flashes. To reactivate the cruise control function, turn the ignition switch back to the “ACC” or “LOCK” position, and then turn it again to the “ON” position. (cid:121) If this indicator light and the “ ” indicator light flash simultaneously during driving, have the vehicle checked by your nearest SUBARU dealer.


To set the time, turn the setting knob clockwise to ad- vance and counterclockwise to retard the time.


UB2013BA


To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.


– CONTINUED – 3-17


Instruments and controls


Light control switch


(cid:132) Headlights


To prevent battery discharge resulting from ac- cidentally leaving your lights on when your ve- hicle is parked, the light switch operates only when the ignition switch is in the “ON” posi- tion. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.


The light switch operates only when the ignition switch is in the “ON” position.


3-18


HS3026BA


To turn on the headlights, turn the knob on the end of the turn signal lever.


first position


Parking lights, instrument panel illumination, tail lights and license plate light are on.


second position


Headlights, parking lights, instrument panel illumina- tion, tail lights, and license plate light are on.


(cid:132) High/low beam change (dimmer)


(cid:132) Headlight flasher


Instruments and controls


HS3026CA


HS3026DA


To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the in- strument panel is also on. To switch back to low beam, pull the lever back to the detent position.


Do not hold the lever in the flashing position for more than just a few seconds.


To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” posi- tion. When the headlights are on high beam, the high beam – CONTINUED – 3-19


Instruments and controls


indicator light “ comes on.


” on the instrument panel also


Turn signal lever


(cid:132) Daytime running light system


The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.


The low beam headlights will automatically come on at reduced brightness when the engine has started, un- der the following conditions: (cid:121) The parking brake is fully released. (cid:121) The light switch is in the “OFF” or “


” position.


3-20


HS3027BC


1) Right turn 2) Left turn To activate the right turn signal, push the turn signal le- ver up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return af- ter cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction


of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.


Illumination brightness control


Instruments and controls


HS3028BB


1) Brighten 2) Darken When the lighting switch is in the “ ” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.


” or “


– CONTINUED – 3-21


Instruments and controls


Parking light switch


that will run down the battery.


HS3029BA


The parking light switch operates regardless of the ig- nition switch position. By pushing the front end of this switch, following lights will come on. – Parking lights – Front and rear side marker lights – Tail lights – License plate lights To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because


3-22


Fog light button


Wiper and washer


Instruments and controls


UB3030BA


The fog lights operate only when the headlights are on low beam. Push the fog light button to turn the fog lights on. Press the button again to turn them off. The indicator light located on the button will illuminate when the fog lights are on.


In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.


(cid:121) Do not operate the washer continuously for more than ten seconds, or when the washer flu- id tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. (cid:121) Do not operate the wipers when the wind- shield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. (cid:121) In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. At- – CONTINUED – 3-23


Instruments and controls


tempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to oper- ate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. (cid:121) If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper operation. (cid:121) Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer flu- id” section in chapter 11.) Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades. (cid:121) Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper


3-24


blades.


NOTE (cid:121) The wiper operates only when the ignition switch is in the “ON” or “ACC” position. (cid:121) Clean your wiper blades and window glass peri- odically with a washer solution to prevent streak- ing, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. (cid:121) Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wip- er operation and streaking on the glass. If you can- not remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with wa- ter. (cid:121) If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wind-


shield wiper blades” section (chapter 11) for re- placement instructions.


(cid:132) Windshield wiper and washer switches (cid:84) Windshield wipers


sition. (cid:84) Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. (cid:84) Wiper intermittent time control (if equipped)


Instruments and controls


P U L L L P U L L L M I S T


OFF


INT


LO


PULLL MIST


HI


UB3022BB


1) MIST To turn the wipers on, push the wiper control lever down.


: Intermittent LO: Low speed HI: High speed To turn the wipers off, return the lever to the “OFF” po-


UB3024BA


When the wiper switch is in the “ the dial to adjust the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your desired interval.


” position, turn


– CONTINUED – 3-25


Instruments and controls


(cid:84) Washer


P U L L L P U L L L M I S T


UB3023BA


To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers oper- ate while you push the button.


3-26


Rear window defogger button


(cid:121) Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. (cid:121) To prevent the battery from being dis- charged, do not operate the defogger continu- ously for any longer than necessary.


The rear window defogger operates only when the ig- nition switch is in the “ON” position. The rear window defogger button is located on the cli- mate control panel. The defogger will automatically shut off after about 15
minutes. If the window clears before that time, push the button to turn it off. It also turns off when the igni- tion switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again.


UB3028BA


To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.


Instruments and controls


Windshield wiper deicer (if equipped)


To prevent the battery from being discharged, do not operate the windshield wiper deicer con- tinuously for any longer than necessary.


UB3029BA


The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the wind- – CONTINUED – 3-27


Instruments and controls


shield wiper deicer, push the button. The indicator light located on the button lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 minutes. If the wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the button to turn the deicer on again.


Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving.


(cid:132) Inside mirror


HS3036BB


1) Tab The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.


3-28


(cid:84) Auto-dimming mirror/compass (if equipped)


HS3037BB


1) Left button 2) Auto dimming indicator 3) Photosensor 4) Right button The auto-dimming mirror/compass has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also con- tains a built-in compass. (cid:121) By pressing and releasing the left button, the auto- matic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming in- dicator light (green) located to the right of the button


Instruments and controls


will illuminate. (cid:121) By pressing and releasing the right button, the com- pass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror sur- face turns bright if the transmission is shifted into re- verse. This is to ensure good rearward visibility during reversing. (cid:86) Photosensors


HS3038BA


The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors – CONTINUED – 3-29


Instruments and controls


detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. (cid:86) Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/ air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metal- lic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then re- lease, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should out- side influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.


3-30


(cid:86) Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map at the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is dis- played. 4. Releasing the button for 3 seconds will exit the zone setting mode.


(cid:132) Outside mirrors (cid:84) Convex mirror (Passenger side)


Objects look smaller in a convex mirror and far- ther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of ob-


jects that you view in convex mirror.


(cid:84) Adjusting mirrors


Instruments and controls


OM-U2737


To adjust the mirrors by hand, push where indicated by the arrows. (cid:84) Remote control mirror switch The remote control mirrors operate only when the ig- nition switch is in the “ON” or “ACC” position.


UB4004BB


1) Selection switch 2) Direction control switch 1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation. The mirrors can also be adjusted manually.


– CONTINUED – 3-31


The indicator light located on the button will come on when the outside mirror defogger heater in operation. To turn it off, push the button again.


Instruments and controls


(cid:84) Outside mirror defogger (if equipped)


To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.


The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position.


UB4004CB


1) Indicator light To turn on the outside mirror defogger, push the but- ton while the engine is running.


3-32


Tilt steering wheel


Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.


Instruments and controls


place. 5. Make sure that the steering wheel is securely locked by moving it up and down.


HS3043BA


1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in


– CONTINUED – 3-33


Instruments and controls


Horn


To sound the horn, push the horn pad.


HS3044BA


3-34


Climate control


Manual heating and air conditioning


Ventilator ....................................................... 4-2
Driver’s side ventilators ................................... 4-2
Center ventilators ............................................. 4-2
Front passenger’s side ventilators ................. 4-3
Air flow selection .............................................. 4-4
system ........................................................ 4-5
Control panel ..................................................... 4-5
Heater operation ............................................... 4-7
Air conditioner operation ................................. 4-10
Operating tips for heater and air conditioner ................................................. 4-11
Air filtration system (if equipped) ................ 4-13


4-1


Climate control


Climate controlVentilator (cid:132) Driver’s side ventilators


(cid:132) Center ventilators


UB4038BB


Move the thumb-wheel up and down or right and left to adjust the flow direction.


UB4039BA


1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.


4-2


(cid:132) Front passenger’s side ventilators


UB4040BB


1) Open 2) Close Move the thumb-wheel up and down or right and left to adjust the flow direction.


Climate control


– CONTINUED – 4-3


Climate control


(cid:132) Air flow selection


4-4


UB4036BA


Manual heating and air conditioning system (cid:132) Control panel


Loading...
x