Login- Download PDF Manual
-
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime running light system
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn signal lever Illumination brightness control Parking light switch Fog light switch (if equipped) Wiper and washer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wiper and washer switches
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Light control switch
3-3
3-5
3-5
3-5
3-6
3-7
3-7
3-7
3-8
3-8
3-9
3-9
3-10
3-10
3-103-11
3-12
3-12
3-13
3-13
3-14
3-15
3-15
3-15
3-15
3-16
3-16
3-16
3-16
3-16
3-17
3-17
3-19
3-19
3-20
3-21
3-22
3-22
3-24BAJA U.S.A..A2310BE–A
Rear window defogger switch Windshield wiper deicer (if equipped) Mirrors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside mirror Outside mirrors
Tilt steering wheel Horn
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-26
3-27
3-28
3-28
3-30
3-32
3-333-2
BAJA U.S.A..A2310BE–A
Ignition switch
Instruments and controls
WARNING
Never turn the ignition switch to “LOCK” while the vehicle is be- ing driven or towed because that will lock the steering wheel, pre- venting steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
The ignition switch has four positions: LOCK, ACC, ON and START.
HB4000CA
B LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.
– CONTINUED –
3-3
BAJA U.S.A..A2310BE–A
n Automatic transmission vehicles
HB4016BA
HB2032CA
The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position.
n Manual transmission vehicles
OM-H0144
The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.
B ACC In this position the electrical accessories (radio, cigarette lighter socket, etc.) can be used.
B ON This is the normal operating position after the engine is started.
3-4
BAJA U.S.A..A2310BE–A
Instruments and controls
B START
CAUTION
Do not turn the ignition switch to the “START” position while the engine is running.
The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
J Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is re- moved from the ignition switch.
J Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened. The light remains on for 10 se- conds and goes out after driver’s door is closed or if the key is turned to the “ON” position.
J Key interlock release (AT vehicles only) If the key can not be turned to the “LOCK” position even when the selec- tor lever is in the “P” position:
HB3011BA
– CONTINUED –
3-5
BAJA U.S.A..A2310BE–A
HB3012BA
OM-H0146
1. Take out the screwdriver from the tool bag. 2. Remove the cover under the steering column using a phillips screwdriver. 3. Turn the ignition key while pressing the key interlock release lever.
Take your vehicle to the nearest SUBARU dealer immediately to have the key interlock system repaired.
Hazard warning flasher
HB8002BA
The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.
3-6
BAJA U.S.A..A2310BE–A
Instruments and controls
To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again.
NOTE When the hazard warning flasher is on, the turn signals do not work.
Meters and gauges
J Speedometer The speedometer shows the vehicle speed.
J Odometer/Trip meter
CAUTION
To ensure safety, do not attempt to change the function of the in- dicator during driving, as an accident could result.
HB3015BB
B Odometer The odometer shows the total distance that the vehicle has been driv- en.
B Double trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero.
– CONTINUED –
3-7
BAJA U.S.A..A2310BE–A
To change the mode indication, briefly push the knob. Each press of the knob changes the function alternately.
A trip meter
B trip meter
To set the trip meter to zero, select either the A trip or B trip meter and push the knob and keep it pushed for more than 1 second.
NOTE If the connection between the combination meter and battery is bro- ken for any reason such as vehicle maintenance or fuse replace- ment, the data recorded on the trip meter will be lost.
J Tachometer
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.
The tachometer shows the engine speed in thousands of revolutions per minute.
J Outside temperature indicator (if equipped) The outside temperature indicator shows the outside temperature in a range from –22°F to 122°F (–30°C to 50°C).
The indicator can give a false reading under any of the following condi- tions: D When there is too much sun. D During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shutdown. D When the actual outside temperature falls outside the specified indi- cator range.
3-8
BAJA U.S.A..A2310BE–A
Instruments and controls
J Fuel gauge The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ignition switch is in the “ACC” or “LOCK” position.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.
J Temperature gauge
CAUTION
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9.
HB2012BB
The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temper- ature and driving conditions.
We recommend that you drive moderately until the pointer of the temper- ature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high rev- ving operation when the engine is not warmed up enough should be
– CONTINUED –
3-9
BAJA U.S.A..A2310BE–A
avoided.
Warning and indicator lights
Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” posi- tion. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:
Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light / Malfunction indicator lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light
If any lights fail to come on, it indicates a burned-out bulb or a malfunc- tion of the corresponding system. Consult your authorized SUBARU dealer for repair.
J Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the reminder chime will sound for about six seconds to remind the driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off automatically after six seconds.
J SRS airbag system warning light AIRBAG When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS frontal airbag and seatbelt pretensioners are in normal operation.
3-10
3
BAJA U.S.A..A2310BE–A
Instruments and controls
If this light comes on while driving or remains illuminated even after a period of about 6 seconds from when the ignition has been turned on, it may indicate that the SRS frontal airbag system or seatbelt pretensioner system is not working properly. Contact your nearest SUBARU dealer im- mediately.
J CHECK ENGINE warning light/Malfunction
indicator lamp
CAUTION
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission control system.
B If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been de- tected. You should have your vehicle checked by an authorized SUBARU dealer immediately.
NOTE This light also comes on when the fuel filler cap is not tightened until it clicks.
If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light
– CONTINUED –
3-11
BAJA U.S.A..A2310BE–A
turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately.
B If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the emission control system. To prevent serious damage to the emission control system, you should do the following: D Reduce vehicle speed. D Avoid hard acceleration. D Avoid steep uphill grades. D Reduce the amount of cargo, if possible. D Stop towing a trailer as soon as possible.
The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.
J Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.
If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alterna- tor belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU dealer immediately.
J Oil pressure warning light
CAUTION
Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.
If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working prop- erly.
3-12
BAJA U.S.A..A2310BE–A
Instruments and controls
If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
J AT OIL TEMPerature warning light
(for AT vehicles)
If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic.
B Automatic transmission control system warning If the light flashes after the engine starts, it may indicate that the auto- matic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.
(U.S.) J ABS warning light (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.
CAUTION
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; how- ever, the conventional brake system continues to operate normal- ly. D The warning light does not come on when the ignition switch is turned to the “ON” position. D The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h).
– CONTINUED –
3-13
BAJA U.S.A..A2310BE–A
D The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
NOTE If the warning light behavior is as shown below, the ABS system may be considered normal. D The warning light comes on right after the engine is started but goes out immediately, remaining off. D The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12
km/h). D The warning light comes on during driving, but it goes out immediately and remains off.When driving with an insufficient battery voltage such as when the en- gine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.
J Brake system warning light
(U.S.)
(Canada)
WARNING
D Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. D If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.
This light has the following two functions:
B Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is
3-14
3
BAJA U.S.A..A2310BE–A
Instruments and controls
fully released.
B Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released. If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch posi- tioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. Have your vehicle checked by a SUBARU dealer immediately.
J Door ajar warning lights The specific door ajar warning light comes on if any door is not fully closed. Always make sure this light is out before you start to drive.
J Switchback door indicator light While the ignition switch is in the “ON” position, the switchback door indi- cator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” position, the switch- back door indicator light flashes for about 20 seconds and goes off when the switchback door is open.
J Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.6 U.S. gal. (10.0 liters, or 2.2 Imp. gal.). It only operates when the igni- tion switch is in “ON” position. NOTE This light does not go out unless the tank is replenished up to an internal fuel quantity of about 3.7 U.S. gal. (14 liters, 3.1 Imp. gal.).
J Front-wheel drive warning light (for AT vehicles) This light comes on when All Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar
– CONTINUED –
3-15
BAJA U.S.A..A2310BE–A
purposes.
J Security system status indicator light
(if equipped)
This light is found at the bottom center of the combination meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, re- fer to the “Security system” in Chapter 2.
J Shift position indicator (for AT vehicles) This indicator shows the position of the shift lever.
J Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
J High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.
J Cargo lamp indicator light
CAUTION
Do not switch on the cargo lamp while driving to avoid distract- ing other drivers.
This indicator light shows that the cargo lamp comes on.
3-16
BAJA U.S.A..A2310BE–A
Clock
Instruments and controls
HB2013BA
To set the time, turn the setting knob clockwise to advance and counter- clockwise to retard the time.
Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper- ates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.
– CONTINUED –
3-17
BAJA U.S.A..A2310BE–A
HB2007BA
HB2014BB
The light switch operates only when the ignition switch is in the “ON” position.
B Headlights To turn on the headlights, turn the knob on the end of the turn signal lever.
first position
Parking lights, instrument panel illumination, tail lights and license plate light are on.
second position
Headlights, parking lights, instrument panel illumination, tail lights, and license plate light are on.
B High/low beam change (dimmer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indi- cator light “a” on the instrument panel is also on. To switch back to low beam, pull the lever back to the detent position.
B Headlight flasher
CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
3-18
BAJA U.S.A..A2310BE–A
Instruments and controls
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” position.
When the headlights are on high beam, the high beam indicator light “a” on the instrument panel also comes on.
J Daytime running light system
WARNING
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “a” position when it is dark out- side.
The low beam headlights will automatically come on at reduced bright- ness when the engine has started, under the following conditions:
D The parking brake is fully released. D The light switch is in the “OFF” or “p” position.
Turn signal lever
Right turn
Left turn
HB2015BB
To activate the right turn signal, push the turn signal lever up. To activate the left turn signal, push the turn signal lever down. When the turn is fin-
– CONTINUED –
3-19
BAJA U.S.A..A2310BE–A
ished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.
To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.
Illumination brightness control
HB2017BB
When the lighting switch is in the “p” or “a” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.
3-20
BAJA U.S.A..A2310BE–A
Parking light switch
Instruments and controls
HB2018BA
The parking light switch operates regardless of the ignition switch posi- tion.
By pushing the front end of this switch, following lights will come on.
– Parking lights – Front and rear side marker lights – Tail lights – License plate lights
To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.
– CONTINUED –
3-21
BAJA U.S.A..A2310BE–A
Fog light switch (if equipped)
The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off.
HB3020BB
The indicator light located on the switch will illuminate when the fog lights are on.
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
CAUTION
D Do not operate the washer continuously for more than ten se- conds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level fre- quently, such as at fuel stops.
3-22
3
BAJA U.S.A..A2310BE–A
Instruments and controls
D Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. D In freezing weather, be sure that the wiper blades are not fro- zen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to operate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. D If the wipers stop during operation because of ice or some oth- er obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper opera- tion. D Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wiper blades. D Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.
NOTE D The wiper operates only when the ignition switch is in the “ON” or “ACC” position. D Clean your wiper blades and window glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the
– CONTINUED –
3-23
BAJA U.S.A..A2310BE–A
windshield or rear window. D Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. D If you cannot eliminate the streaking even after following this pro- cedure, replace the wiper blades with new ones. Refer to the “Wiper blade replacement” section (chapter 11) for replacement instruc- tions.
J Windshield wiper and washer switches
B Windshield wipers
To turn the wipers on, push the wiper control lever down.
HB3022BB
: Intermittent LO : Low speed HI : High speed
To turn the wipers off, return the lever to the “OFF” position.
3-24
BAJA U.S.A..A2310BE–A
B Wiper intermittent time control
Instruments and controls
HB3024BA
” position, turn the dial to adjust
When the wiper switch is in the “ the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your de- sired interval.
B Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever.
B Washer
To wash the windshield, push the washer button at the end of the wip-
HB3023BA
– CONTINUED –
3-25
BAJA U.S.A..A2310BE–A
er control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button.
Rear window defogger switch
CAUTION
D Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. D To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
The rear window defogger operates only when the ignition switch is in the “ON” position. The rear window defogger switch is located on the climate control panel.
The defogger will automatically shut off after about 15 minutes. If the win- dow clears before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again.
HB5009BB
To turn on the defogger, push the switch. To turn it off, push the switch again. The indicator light located on the switch lights up while the rear window
3-26
BAJA U.S.A..A2310BE–A
Instruments and controls
defogger is operating.
Windshield wiper deicer (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate the windshield wiper deicer continuously for any longer than neces- sary.
HB3021BB
The windshield wiper deicer operates only when the ignition switch is in the “ON” position.
Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the windshield wiper deicer, push the switch. The indicator light located on the switch lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 min- utes. If the wiper blades have been deiced completely before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the switch to turn the deicer on again.
– CONTINUED –
3-27
BAJA U.S.A..A2310BE–A
Mirrors
Always check that the inside and outside mirrors are properly adjusted before you start driving.
J Inside mirror
HB4003BB
The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.
B Auto-dimming mirror/compass (if equipped)
The auto-dimming mirror/compass has an anti-glare feature which au- tomatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass.
HB6019BB
3-28
BAJA U.S.A..A2310BE–A
Instruments and controls
D By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. D By pressing and releasing the right button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror surface turns bright if the transmission is shifted into reverse. This is to ensure good rear- ward visibility during reversing.
n Photosensors
HB6020BA
The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other simi- lar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator.
n Compass calibration 1. For optimum calibration, switch off all nonessential electrical ac- cessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or
– CONTINUED –
3-29
BAJA U.S.A..A2310BE–A
structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has oc- curred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.
n Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Com- pass calibration zone” map at the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be dis- played. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode.
J Outside mirrors
B Convex mirror (Passenger side)
WARNING
Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of objects that you view in convex mir- ror.
3-30
BAJA U.S.A..A2310BE–A
B Adjusting mirrors To adjust the mirrors by hand, push where indicated by the arrows.
Instruments and controls
OM-H2737
B Remote control mirror switch The remote control mirrors operate only when the ignition switch is in the “ON” or “ACC” position.
HB4004BB
1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation.
The mirrors can also be adjusted manually.
– CONTINUED –
3-31
BAJA U.S.A..A2310BE–A
B Outside mirror defogger (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position.
HB4004CB
To turn on the outside mirror defogger, push the switch while the en- gine is running. The indicator light located on the switch will come on when the out- side mirror defogger heater in operation.
To turn it off, push the switch again.
Tilt steering wheel
WARNING
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.
3-32
BAJA U.S.A..A2310BE–A
Instruments and controls
HB4002BA
1. Adjust the seat position. Refer to the “Front seat” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down.
Horn
To sound the horn, push the horn pad.
OM-H0440
– CONTINUED –
3-33
BAJA U.S.A..A2310BE–A
3-34
BAJA U.S.A..A2310BE–A
Climate control
Ventilator Manual heating and air conditioning system
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heater operation Air conditioner operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating tips for heater and air conditioner Air filtration system (if equipped)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
4-2
4-4
4-7
4-10
4-12
4-13BAJA U.S.A..A2310BE–A
Ventilator
B Center and side ventilators
B Adjustable side defroster grille (driver’s side – if equipped)
HB5001BB
Normal position
Side defroster grille
Windshield defrost assist position
Fin
HB5002BB
HB5003BB
The driver’s side defroster grille is adjustable. The normal position as shown in the diagram directs warm air to the side glass. When more rapid defrosting of the windshield is desired, the air flow can be directed temporarily toward the windshield to assist the windshield defroster. If this is done, the driver’s side grille should always be returned to its normal position so that the warm air flow can then be used to defrost the driver’s side window.
4-2
BAJA U.S.A..A2310BE–A
B Air flow selection
Climate control
HB5006BA
HB5006DA
HB5006FA
HB5006CA
HB5006EA
– CONTINUED –
4-3
BAJA U.S.A..A2310BE–A
Manual heating and air conditioning system
B Control panel
HB5004BC
1. Temperature control dial 2. Fan speed control dial 3. Air flow control dial 4. Air conditioner button 5. Air inlet selection button 6. Rear window defogger button (Refer to “Rear window defogger” in chapter 3.)
n Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue area (cool) to red area (warm).
n Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds.
n Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets and the foot
outlets.
4-4
BAJA U.S.A..A2310BE–A
Climate control
: Air flows through the foot outlets and some through the wind-
shield defroster outlets.
: Air flows through the windshield defroster outlets and foot
outlets.
: Air flows through the windshield defroster outlets.
” or “
NOTE When the dial is placed in the “ ”position, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quickly. At the same time, the air inlet selection is automatically set to “Outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button.
n Air conditioner button
HB5010BB
The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in operation to turn on the air conditioner. The indicator light will come on. Push it again to turn off the air conditioner.
– CONTINUED –
4-5
BAJA U.S.A..A2310BE–A
n Air inlet selection button
WARNING
Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condi- tion clears.
HB5008BB
ON position (Recirculation): Interior air is recirculated inside the ve- hicle. Push the air inlet selection button to the ON position. The indi- cator light will come on. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button again to the OFF position. The indicator light will go off.
4-6
BAJA U.S.A..A2310BE–A
J Heater operation
B Defrosting or defogging the windshield
Climate control
HB5011AA
To direct warm air to the windshield and front door windows: 1. Set the air flow control dial to “ 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed.
”.
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
B Heating and defrosting
HB5012AA
– CONTINUED –
4-7
BAJA U.S.A..A2310BE–A
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to “ 2. Set the temperature control dial to the desired temperature level. 3. Set the fan speed control dial to the desired speed.
”.
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
B Heating
HB5013AA
To direct warm air toward the floor: 1. Set the air inlet selection button to the “OFF” position 2 Set the air flow control dial to “ 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed.
”.
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “
” position.
4-8
BAJA U.S.A..A2310BE–A
B Bi-level heating
Climate control
HB5014AA
This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the “OFF” position. 2. Set the air flow control dial to “ 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed.
”.
Setting the temperature control dial fully turned to the red area or blue area decreases the temperature difference between the air from the instrument panel outlets and the air from the foot outlets.
B Ventilation
WARNING
Continued operation in the “ON” position may fog up the win- dows. Switch to the “OFF” position as soon as the outside dusty condition clears.
– CONTINUED –
4-9
BAJA U.S.A..A2310BE–A
HB5015AA
To force outside air through the instrument panel outlets: 1. Set the air inlet selection button to the “OFF” position. 2. Set the air flow control dial to “ 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed.
”.
When driving on a dusty road, set the air inlet control button to the “ON” position.
J Air conditioner operation
B Cooling or dehumidifying
For cooling and dehumidification of the passenger compartment, air flows through the instrument panel outlets:
HB5016BB
4-10
BAJA U.S.A..A2310BE–A
Climate control
1. Set the air inlet selection button to the “OFF” position. 2. Set the air flow control dial to “ 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue area. 5. Set the fan speed control dial at the desired speed.
”.
B Defrosting or defogging
HB5011BB
To direct warm air to the windshield and front door windows: 1. Set the air outlet control dial to “ 2. Set the temperature control dial to the red area. 3. Set the fan speed control dial at the highest speed.
”.
– CONTINUED –
4-11
BAJA U.S.A..A2310BE–A
Operating tips for heater and air conditioner
B Cleaning ventilator grille
HBF046BA
Always keep the front ventilator inlet grille free of snow, leaves, or oth- er obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser.
B Efficient cooling after parking in direct sunlight After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency.
B Lubrication oil circulation in the refrigerant circuit Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-sea- son to circulate its oil.
B Checking air conditioning system before summer season Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer.
4-12
4
BAJA U.S.A..A2310BE–A
Climate control
B Cooling and dehumidifying in high humidity and low tempera-
ture weather condition
Under certain weather conditions (high relative humidity, low tempera- tures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
B Air conditioner compressor shut-off when engine is heavily
loaded
To improve acceleration and gas mileage, the air conditioner com- pressor is designed to temporarily shut off during air conditioner op- eration whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.
B Refrigerant for your climate control system Your air conditioner uses ozone friendly refrigerant HFC134a. There- fore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Air filtration system (if equipped)
If your vehicle’s air conditioning system is equipped with a optional air filtration system, replace the filter element according to the replacement schedule shown below. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more frequently. Have your filter checked or replaced by your SUBARU dealer.
Replacement schedule:
Every 12 months or 9,300 miles (15,000 km) whichever comes first
NOTE The filter can influence the air conditioning, heating and defroster performance if not properly maintained.
– CONTINUED –
4-13
BAJA U.S.A..A2310BE–A
4-14
BAJA U.S.A..A2310BE–A
Audio
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna system Installation of accessories Audio set AM/FM radio with CD player In-dash 6 CD auto changer (if equipped) Precautions to observe when handling
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
a compact disc (CD)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2
5-2
5-3
5-4
5-135-16
BAJA U.S.A..A2310BE–A
Antenna system
B Pillar mounted antenna
Pull the antenna out to extend it to its full length.
HB5070BA
B FM reception Although FM is normally static free, reception can be affected by the surrounding area, atmospheric conditions, station strength and trans- mitter distance. Buildings or other obstructions may cause momentary static, flutter or station interference. If reception continues to be unsat- isfactory, switch to a stronger station.
Installation of accessories
Always consult your SUBARU dealer before installing a citizen band ra- dio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
5-2
BAJA U.S.A..A2310BE–A
Audio
Audio set
Your SUBARU is equipped with the following audio set. See the pages indicated in this section for operating details.
B AM/FM radio with CD player
HB5066AA
D Radio operation: refer to page 5-4
D CD (compact disc) player operation: refer to page 5-7
D CD changer control: refer to page 5-10B In-dash 6 CD auto changer (Optional audio unit — if equipped)
D Inserting and removing a disc or all discs: refer to page 5-13
HB5040AA
– CONTINUED –
5-3
BAJA U.S.A..A2310BE–A
AM/FM radio with CD player
The audio set will operate only when the ignition switch is in the “ACC” or “ON” position.
Radio operation
HB5067BB
1 Power switch/Volume, Tone, Balance, Fader control dial
2 BAND button 3 Tuning buttons
4 Preset buttons 5 AUDIO button 6 SCAN button
B Power switch and volume/bass/treble/fader/balance control n Power switch and volume control (PWR/VOL) The dial 1 is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial.
n Tone and balance control (AUDIO) The volume control dial 1 normally functions as a volume control. This dial becomes a control for Bass, Treble, Fader or Balance when you select the appropriate tone and balance control mode.
5-4
BAJA U.S.A..A2310BE–A
Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds.
Audio
To change control modes: Each brief press of the “AUDIO” button 5 changes control modes in the following sequence starting from vol- ume control mode. (When the radio is first turned on, the control mode is in the volume control.) Volume (VOL)
Balance (BAL)
Treble (TRE)
Fader (FAD)
Bass (BAS)
The “AUDIO” button 5 is used for selecting the following control modes:
Display
Control mode
Turn counterclockwise
Turn clockwise
HB5036BA
BAS
TRE
FAD
Bass control
For less bass
For more bass
Treble control
For less treble
For more treble
Fader control
To increase rear speaker volume and decrease front
To increase front speaker volume and decrease rear
speaker volume
speaker volume
BAL
Balance control
To increase left speaker
volume and decrease right
To increase right speaker volume and decrease left
speaker volume
speaker volume
VOL
Volume control
For less volume
For more volume
B Waveband selection n FM/AM selection Push the “BAND” button 2 to select FM1, FM2 or AM reception. The
– CONTINUED –
5-5
BAJA U.S.A..A2310BE–A
display indicates which one is currently selected.
B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
B Tuning (TUNE) n Manual tuning (TUNE) Press the tuning button 3 marked “Y” to increase the tuning frequen- cy and press the tuning button marked “B” to decrease it. Each time the button is pressed, the frequency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode. Constant pressure on the button causes a continuous change in the frequency.
n Automatic tuning (SCAN) Press the “SCAN” button 6 to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while display- ing the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
B Selecting preset stations Presetting a station with a “preset button” 4 allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset.
B How to preset stations 1. Press the “BAND” button 2 to select FM1, FM2 or AM reception. 2. Press the “SCAN” button or tune the radio manually until the
5-6
BAJA U.S.A..A2310BE–A
Audio
desired station frequency is displayed. 3. Press one of the preset buttons for more than 2 seconds to store the frequency. At this time, there will momentarily be no sound from the radio. If the button is pressed for less than 2 seconds, the preced- ing selection will remain in memory.
NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is neces- sary to reset the preset buttons.
Compact disc player operation
7 Disc slot 8 CD button 9 Eject button Q Fast forward and track up
button
W Fast reverse and track down
HB5067CB
button
E Random button R Repeat button T Scan button Y PWR (power) switch
B To playback a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of
– CONTINUED –
5-7
BAJA U.S.A..A2310BE–A
the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A 8 cm/3 inch CD may also be used without any adapter.
NOTE D DO NOT INSERT TWO DISCS INTO THE DISC INSERTION SLOT AT A TIME. D Be sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. D After the last song finishes, the player will automatically return to track 1 (the first song on the disc).
n When CD is in the player When the “CD” button 8 is pressed, the player will start playback.
NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc).
B To stop playback of a CD When the “PWR” button Y is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again.
B To select a song from its beginning n Forward direction Briefly press the “Y” button Q to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase.
n Backward direction Briefly press the “B” button W to skip to the beginning of the current track. Each time the button is pressed, the indicated truck number will decrease.
5-8
BAJA U.S.A..A2310BE–A
Audio
B Fast forwarding and fast reverse n Fast forward Press the “Y” button Q continuously for more than 0.5 second to fast forward the disc. Release the button to stop fast forwarding.
n Fast reverse Press the “B” button W continuously for more than 0.5 second to fast reverse the disc. Release the button to stop fast reverse.
B Repeat playback Use this to play a certain track repeatedly. During playback, press the “RPT” button R and release it in less than 2 seconds. The “RPT” indi- cator will come on and the song will be played continuously. To can- cel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.
B Random playback Use this to play the tracks on the disc in random order. During play- back, press the “RDM” button E and hold it in for more than 2 se- conds. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored.
B Scan Press the “SCAN” button T and release it in less than 2 seconds, and you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored.
B To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position.
” 9. The disc will be ejected.
– CONTINUED –
5-9
BAJA U.S.A..A2310BE–A
NOTE D Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. D To protect the disc, the disc is automatically loaded if it is left in the ejected position for more than approximately 15 seconds (Auto Reload). In this case, the disc is not played.
CD changer control (If optional in dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter.
U CD button I Track selection buttons O RAND (Random) button
HB5067DB
P RPT (Repeat) button A SCAN button
B To start playback Press the “CD” button U. The “CD” indicator will come on and the disc number will appear on the display and the CD changer will start playback.
5-10
BAJA U.S.A..A2310BE–A
Audio
NOTE D If the “CD” button is pressed during a radio broadcast, the CD changer will interrupt the broadcast. D At the end of the disc, playback automatically continues with the next disc. D After playback on the last disc finishes, the player will auto- matically return to the first disc. D If you have loaded fewer than 6 discs, any missing disc is automatically skipped.
B Selection of a desired disc Discs cannot be selected using the main audio unit. To select a disc, press one of the “Disc select” buttons (these are numbered from 1 to 6) on the CD changer unit. The disc will begin to play.
B To select a song from its beginning Briefly press the “Y” button I to skip to the beginning of the next track and briefly press the “B” button to skip to the beginning of the current track.
B Fast-forwarding and fast-reverse Press the “Y” button I continuously for more than a half second to fast-forward the disc. Press the “B” button continuously for more than a half second to fast reverse the disc. Release the button to stop fast forwarding or fast reverse.
B Repeat Press the “RPT” button P while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.
B Random playback Press the “RAND” button O while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order.
– CONTINUED –
5-11
BAJA U.S.A..A2310BE–A
To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored.
B Scan (a convenient way to become familiar with a disc) 1. Press the “SCAN” button A.
– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all pro- grams. Then, normal playback starts.
2. Press the “SCAN” button again when you hear a track you like.
– Normal playback resumes.
B To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
5-12
BAJA U.S.A..A2310BE–A
In-dash 6 CD auto changer (if equipped)
Audio
1 Disc slot 2 Disc indicators (disc No.1 to
6)
3 Disc select buttons
(disc No.1 to 6)
4 Eject button
HB5040BB
CAUTION
D Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer. D Use only music CDs identified by a D Do not use CDs listed below which could cause damage to the CD player.
mark.
D 3-inch (8 cm) compact disc. D Any disc with a peel-off or seal on it. D Any disc with scratches and/or dust. D Bent disc. D Cleaning disc. D CD accessory. (E.g., 3-inch (8 cm) disc adapter)
D Do not insert or remove any disc when the automatic transmis- sion selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).
– CONTINUED –
5-13
BAJA U.S.A..A2310BE–A
B To insert a disc 1. Press one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light 2 is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 se- conds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” 1
door will close. Repeat step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat step 1 and 2 choosing a different disc select button.B To insert six discs at a time 1. Press and hold the “Disc select” button number 1 until all disc indi- cators begin blinking (about 1.5 seconds). 2. The indicators will blink for 15 seconds. During this period, insert desired six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.)
B To remove a disc 1. Press the desired one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light is on. 2. Press the “Eject button” 4. The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat step 1 and 2 choosing a different “Disc select” button. (To remove discs when the ignition switch is in the “Lock” position, press the “Eject” button, and the first disc will be ejected. Press the “Eject” button again, and the next disc will be ejected and so on. At this time, the “Disc select” buttons are disabled.)
5-14
BAJA U.S.A..A2310BE–A
Audio
B To remove all discs at one time 1. Press and hold the “Eject” button 4 until all “Disc” indicators begin blinking (about 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on.
B To replace a playing disc with another Simply press the desired one of “Disc select” buttons 3 (numbered from 1 to 6) or press the “DISC UP” or “DISC DOWN” button on the radio unit to select the desired disc, and the disc will begin to play.
B Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode. OFF: No disc is loaded or the ignition switch is in the “LOCK” position.
B Function control Refer to CD player control operating instructions described in the “AM/FM radio with CD player” section.
– CONTINUED –
5-15
BAJA U.S.A..A2310BE–A
Precautions to observe when handling a compact disc (CD)
Use only compact discs (CDs) that have the mark shown below. CD- RWs cannot be used. Also, some CD-Rs cannot be played.
HB5062AA
D In cold and/or rainy weather, dew can form inside the CD player, pre- venting normal operation. If this happens, eject the CD and wait for the player to dry out. D Skipping may occur when the CD player is subjected to severe vibra- tion (for example, when the vehicle is driven on a rough surface). D To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamina- tion could cause poor tone quality. Do not touch the disc surface. D Use a clean disc whenever possible. If there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzene, alcohol, etc. D Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-standard shape (for example, a heart shape). Malfunctions or problems might result. D A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or hot days.
5-16
BAJA U.S.A..A2310BE–A
Audio
HB5061BA
– CONTINUED –
5-17
BAJA U.S.A..A2310BE–A
5-18
BAJA U.S.A..A2310BE–A
Interior and exterior equipments
Interior light Dome light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map light Sun visors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vanity mirror
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage compartment
Glove box Center console Rear center console Coin compartment Rear quarter storage box
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holder Cigarette lighter socket Ashtray Convenience hook
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coat hook Cargo net hooks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cargo tie-down hooks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Floor mat (if equipped) Cargo bed
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bed extender (if equipped) Cargo lamp Bed cover (if equipped) Roof rail and crossbar Sport activity lights (if equipped)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2
6-2
6-3
6-3
6-4
6-4
6-5
6-5
6-6
6-6
6-7
6-7
6-9
6-12
6-12
6-12
6-13
6-14
6-15
6-16
6-17
6-20
6-21
6-23
6-29BAJA U.S.A..A2310BE–A
Interior light
J Dome light
HS6003BC
The dome light switch has three positions: ON: The light stays on continuously. DOOR (middle position): The light comes on when any of the doors is open. The light remains on for several seconds and gradually goes out after all doors are closed.
The light also can be turned on by use of the keyless entry transmitter. See the “Keyless entry system” in chapter 2 for detailed information. OFF: The light stays off.
When leaving your vehicle, make sure the light goes out to avoid battery discharge.
6-2
BAJA U.S.A..A2310BE–A
Map light
Interior and exterior equipments
HB2034CC
To turn on the map light, push the switch. To turn it off, push the switch again.
When leaving the vehicle, make sure the light is turned off to avoid bat- tery discharge.
Sun visors
HB7001BA
To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
– CONTINUED –
6-3
BAJA U.S.A..A2310BE–A
J Vanity mirror
