Download PDF Manual

mental conditions. Range may be reduced near sources of RF interfer- ence such as power plants and radio/television broadcasting towers.


The keyless entry system does not operate when the key is inserted in the ignition switch.


2-6


BAJA U.S.A..A2310BE–A


Keys and doors


HB1000BF


B Locking the doors Briefly press the “LOCK/ARM” button (for less than two seconds) to lock all doors. An electronic chirp will sound one time and the turn signal lights will flash one time. If any of the doors is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors are not properly closed. When you close the door, it will automatically lock.


NOTE If the “LOCK/ALARM” button is pressed for two seconds or long- er, the panic alarm will sound. When locking the doors in normal circumstances, press the “LOCK/ALARM” button for less than two seconds. For details on the panic alarm, refer to “Sounding the panic alarm”.


B Unlocking the doors Briefly press the “UNLOCK/DISARM” button (for less than two seconds) to unlock the driver’s door. An electronic chirp will sound two times and the turn signal lights will flash two times. To unlock all doors, briefly press the “UNLOCK/DISARM” button a second time within 5 seconds.


NOTE If the interval between the first and second presses of the “UN-


– CONTINUED –


2-7


BAJA U.S.A..A2310BE–A


LOCK/DISARM” button (for unlocking of all of the doors is ex- tremely short, the system may not respond.


B Illuminated entry The interior (dome) light will illuminate when the “UNLOCK/DISARM” button is pressed. These lights stay illuminated for approximately 30
seconds if any of the doors is not opened. If the “LOCK/ARM” button is pressed before 30 seconds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light must be set to the middle position in order for this function to operate.


J Vehicle finder function Use this functon to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the ve- hicle, pressing the “LOCK/ARM” button three times in a five-second peri- od will cause your vehicle’s horn to sound one time and its turn signal lights to flash three times.


B Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30 seconds.


B Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If desired, you may turn the audible signal off. To turn the audible signal off, unlock the doors by pushing “UNLOCK/ DISARM” button and then simultaneously depress “LOCK/ARM” and “UNLOCK/DISARM” buttons for more than two seconds. An electronic chirp will sound two times and the turn signal lights will flash two times to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the doors by pushing “UNLOCK/


2-8


BAJA U.S.A..A2310BE–A


Keys and doors


DISARM” button and then simultaneously depress “LOCK/ARM” and “UNLOCK/DISARM” buttons for more than two seconds. An electronic chirp will sound one time and the turn signal lights will flash one time to inform you that the audible signal has been turned on.


B Replacing the battery


CAUTION


Do not let dust, oil or water get on or in the transmitter when replacing the battery.


When the transmitter battery begins to get weak, transmitter range will begin to decrease and the LED will not illuminate. Replace the battery as soon as possible.


Positive (+) side facing up


HB1001BA


HB1002BB


To replace the battery: 1. Remove the two screws on the back of the transmitter case by using a phillips screwdriver. 2. Separate the case. 3. Remove the old battery from the holder. 4. Replace with a new battery (Type CR2032 or equivalent) making sure to install the new battery with the positive (+) side facing up. 5. Install the back half of the transmitter case. 6. Reinstall the two screws on the back of the transmitter case. After the battery is replaced, the transmitter must be synchro- nized with the keyless entry system’s control unit. Press either


– CONTINUED –


2-9


BAJA U.S.A..A2310BE–A


the “LOCK/ARM” or “UNLOCK/DISARM” button six times to syn- chronize the unit.


B Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system.


n Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the sys- tem or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or dif- ferent.


To enter the programming mode:


1 Press to dis- arm the security system (if so equipped).


HB1000CB


HB1005BC


1. Disarm the security system. (if your vehicle is equipped with the optional security system.) 2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.


2-10


BAJA U.S.A..A2310BE–A


Keys and doors


HB2032BB


4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15 seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode.


NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this procedures.


To program the transmitters:


3 Press any button.


HB1005BB


HB1000DB


1. Open the driver’s door. 2. Close the driver’s door. 3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound two times to indicate


– CONTINUED –


2-11


BAJA U.S.A..A2310BE–A


that the transmitter has been programmed.


Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter.


To exit the programming mode: 1. After all of your transmitters are programmed, remove the key from the ignition switch. The horn will sound three times to indicate that the system has exited the programming mode. 2. Make sure that the keyless entry system properly operates by operating each transmitter.


n Deleting old transmitter codes The control unit of the keyless entry system has four memory loca- tions to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code remains in the memory. For security reasons, lost transmitter codes should be deleted from the memory. To delete old transmitter codes, program four transmitter codes into the system. If you have only one current transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory.


NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their trans- mitter code will be programmed into your system, allowing them unauthorized access to your vehicle.


2-12


BAJA U.S.A..A2310BE–A


Keys and doors


Security system (if equipped)


The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key.


The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch.


B System operation The security system will give the following alarm indications when trig- gered: D The turn signal lights will flash and the horn will sound intermit- tently. In addition, the starter motor will not operate. D The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tampered with again. The alarm will continue for six times if any sensor continues to be activated.


The alarm is triggered by: D Opening a door. D Application of physical shock to the vehicle (e.g. breaking glass or forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher lev- els of shock are detected and the system will go into full alarm. D Ignition switch being turned on while in armed state.


NOTE D The alarm will not be triggered by opening the switchback door. D The alarm may not be triggered when the window is broken with a sharp-edged tool. D With the valet mode selected, the security system does not op- erate and the turn signal lights do not flash when the remote


– CONTINUED –


2-13


BAJA U.S.A..A2310BE–A


transmitter is used for locking and unlocking. The security system indicator light in the combination meter flashes twice per second to show that the valet mode is selected. For details, refer to “Valet mode” in this section.


B Arming the system n To arm the system using remote transmitter


Press to Disarm the system.


Press to Arm the system.


HB1000EB


HB2033BB


1. Close all windows and moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close all doors. 6. Briefly press the “LOCK/ARM” button (for less than two seconds). All doors will lock, an electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light starts flashing slowly (approximately once every two seconds).


If any of the doors (except the switchback door) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors are not properly closed. When you close the door, the system will automatically arm and doors will auto- matically lock.


2-14


BAJA U.S.A..A2310BE–A


n To arm the system using power door locking switches


Keys and doors


HB2024CC


1. Close all windows and the moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close the doors but leave only the driver’s door or the front pas- senger’s door open. 6. Push the power door locking switch forward (“LOCK” side) to set the door locks. 7. Close the door. An electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light will start flashing slowly (approximately once every two seconds) to inform you that the system has armed.


NOTE The system can be armed even if the engine hood, the windows, the switchback door and/or moonroof are open. Always make sure that they are fully closed before arming the system.


B Disarming the system Briefly press the “UNLOCK/DISARM” button (for less than two seconds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound two times, the turn signal lights will flash two times and the indicator light will go off.


To unlock all other doors, briefly press the “UNLOCK/DISARM” button


– CONTINUED –


2-15


BAJA U.S.A..A2310BE–A


a second time.


n Emergency disarming If you cannot disarm the system using the transmitter (i.e. the trans- mitter is lost, broken or the transmitter battery is too weak), you can disarm the system without using the transmitter.


To disarm the system: 1. Unlock the door with the key and then open the door. 2. The alarm will sound. 3. Insert the key into the ignition switch and cycle it from “LOCK” to “ON” three (3) times within 5 seconds.


B Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the remote is pressed, the alarm will be deacti- vated after approximately 30 seconds.


B Valet mode When you choose the valet mode, the security system does not oper- ate. In valet mode, the remote transmitter is used only for locking and unlocking the doors and panic activation.


To enter the valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button depressed for more than two seconds. The security system indicator light will continue to flash 2 times per second indicating that the system is in the valet mode.


To exit valet mode, open the driver’s door and keep the “UNLOCK/ DISARM” button pressed for more than two seconds. The indicator will stop flashing.


B Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the


2-16


BAJA U.S.A..A2310BE–A


Keys and doors


remote transmitter. Note that in this mode, DOORS MUST BE MANU- ALLY LOCKED.


n To enter the passive mode


WARNING


Do not disconnect or tamper with any yellow connector and/or any harness covered with yellow insulation and/or tape. Doing so could result in accidental inflation of the SRS airbag or could make the SRS airbag system inoperative, which may result in serious injury.


HB2036BA


HB2038BB


1. Remove the side sill cover on the driver’s side.


1) Open the driver’s door. 2) Remove the two clips fastening the front portion of the cover with a screwdriver. 3) Remove the side sill cover by pulling it up.


2. Connect the white (1 pole) connector. 3. Turn the ignition switch from “LOCK” to “ON”. 4. Install the side sill cover.


To place the system in active arming mode (remote required for ac- tivation), disconnect the white connector.


– CONTINUED –


2-17


BAJA U.S.A..A2310BE–A


n Arming the system


CAUTION


In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.


HB2031BB


HB2024DB


1. Turn the ignition switch to “ON”. 2. Turn the ignition switch from “ON” to “LOCK” and remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after one min- ute.


In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arm- ing will take place immediately regardless of whether or not the pas- sive mode has been selected.


B Disarming the system To disarm the system, briefly press the “UNLOCK/DISARM” button on


2-18


BAJA U.S.A..A2310BE–A


Keys and doors


the transmitter.


B Tripped sensor identification If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the system, this indicates that the alarm was triggered. The number of times the indicator light flashes indi- cates what sensor caused the alarm condition.


To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to “ON” two times. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.


The indicator light provides the following indications. Flashing one time: Any door has been opened. Flashing three times: The impact sensor in the system’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected.


NOTE The battery must be reconnected before the indicator light will flash.


To exit this mode, close the door and turn the ignition switch to “ON”.


– CONTINUED –


2-19


BAJA U.S.A..A2310BE–A


Child safety locks


WARNING


Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.


HB2002BB


Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.


When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.


2-20


BAJA U.S.A..A2310BE–A


Windows


J Power windows


Keys and doors


WARNING


To avoid serious personal injury caused by entrapment, you must observe the following warnings: D When operating power windows, be extremely careful to pre- vent anyone’s fingers, arms or head from being caught in the window. D Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.


The power windows operate only when the ignition switch is in the “ON” position.


B Driver’s side switches


HB2008BB


– CONTINUED –


2-21


BAJA U.S.A..A2310BE–A


HB2008DB


All door windows can be controlled by the power window switch clus- ter at the driver side door.


n Operating the driver’s window To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up lightly.


To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held.


n Operating the passengers’ windows To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired posi- tion.


n Locking the passengers’ windows To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.


2-22


BAJA U.S.A..A2310BE–A


B Passengers’ side switches


Keys and doors


HB2009CB


HB2005BB


To open the window, push the switch down and hold it until the win- dow reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position.


When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ win- dows cannot be operated with the passengers’ switches.


Tailgate


CAUTION


Keep the tailgate closed when the vehicle is moving. If you must drive with the tailgate open, use the optional Subaru Bed Extender and place the License Plate Bracket at its fully lowered/ open position. Cargo must not stick out beyond the Extender. Otherwise a dangerous road hazard or personal injury could result.


– CONTINUED –


2-23


BAJA U.S.A..A2310BE–A


HB2050BA


Before opening the tailgate, remove any object on the upper surface of the rear bumper to avoid damaging the tailgate. To open the tailgate, lift up on its handle while pulling the tailgate toward you. The support cables hold the tailgate open.


See “Loading your vehicle” section in Chapter 8 for precautions in load- ing cargo.


To close the tailgate, firmly push it upward until it latches.


After you put the tailgate back up, pull it back toward you to be sure it latches securely.


J License plate bracket


When you drive with the tailgate open and with the bed extender used,


HB2051BA


2-24


BAJA U.S.A..A2310BE–A


Keys and doors


the license plate bracket must be placed at its fully lowered/open posi- tion to make the rear license plate visible.


CAUTION


In order to avoid damaging the license plate bracket or the bum- per, the license plate bracket must be in its fully lowered/open position before the tailgate is lowered.


HB2054BA


HB2053BA


To use the license plate bracket at its lowered/open position, push the two release buttons and pull the license plate bracket up until it clicks. And then open the tailgate. If your vehicle is equipped with a trailer hitch, remove the ball mount from the hitch receiver tube before opening the tailgate. Failure to follow this procedure could result in damage to the license plate bracket. When you drive with the tailgate closed, the license plate bracket must be restored to its original position. To restore the license plate bracket to its original position, close the tail- gate, and then pull the license plate bracket down until it clicks. If the license plate bracket is hard to be restored to its original position, mud may have accumulated on the back of the license plate bracket. Remove accumulated mud before pulling the license bracket down.


– CONTINUED –


2-25


BAJA U.S.A..A2310BE–A


CAUTION


In order to avoid damaging the license plate bracket or the bum- per, the license plate bracket must be restored to its original posi- tion until it clicks.


Switchback door


HB2052BA


With the switchback door open, you can increase the usable cargo space and can carry long objects.


WARNING


Secure long objects properly to prevent them from sliding for- ward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equiv- alent.


CAUTION


Pay attention that your fingers do not get pinched with the switchback door when opening and closing it.


2-26


BAJA U.S.A..A2310BE–A


To open the switchback door:


Keys and doors


HB1112BA


1. Pull up the rear seat cushion. Refer to “Rear seats” section in Chapter 1 for operating details.


HB1112CB


HB1113BA


2. Unlock the rear seatback by pulling up on the knob and fold down the rear seatback. Confirm that the pins located at the bottom of the seat cushion is inserted into the slots at the top of the seatback.


– CONTINUED –


2-27


BAJA U.S.A..A2310BE–A


HB1114BA


HB1115BA


3. Fold down the switchback door by releasing the lock knob. Then you can have a flat and larger cargo space. 4. Place the long object on the cargo bed through the switchback door opening. Be sure all items are secured in place. NOTE D When opening the switchback door in snow, accumulated snow in the cargo bed may enter the passenger compartment which could result in dampness in the passenger compartment. Prior to opening of the switchback door, brush off the snow completely. D Close the switchback door whenever you leave the vehicle to pre- vent unauthorized entry.


WARNING


The switchback door should be kept completely shut when the vehicle is idling in an enclosed or partially enclosed area to avoid the possibility of exhaust gas entering the passenger compart- ment. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is extremely dangerous, or even lethal if inhaled. To ensure that exhaust gas cannot penetrate the switch- back door, make certain that there are no obstructions between the door and the vehicle body that prevent the door from fully closing or that crimp the weather strip around the door.


2-28


BAJA U.S.A..A2310BE–A


To close the switchback door, firmly push it upward until it latches. Return the seatback and seat cushion to their original positions and make sure they are securely locked.


Keys and doors


CAUTION


After returning the seatback to its original position, make sure that the rear seatback has been securely locked. When securely locked, the red marks on the locking knobs are no longer visible.


J Switchback door indicator light


HB4010JA


While the ignition switch is in the “ON” position, the switchback door indi- cator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” position, the switch- back door indicator light flashes for about 20 seconds and goes off when the switchback gate is open.


– CONTINUED –


2-29


BAJA U.S.A..A2310BE–A


Moonroof


WARNING


Never let anyone’s hands, arms, head or any objects protrude from the moonroof. He/she could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident.


To avoid serious personal injury caused by entrapment, you must observe the following warnings: D Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.


CAUTION


D Do not sit on the edge of the open moonroof. D Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.


J Tilting/sliding moonroof The moonroof has both tilting and sliding functions. The moonroof operates only when the ignition switch is in the “ON” posi- tion.


2-30


BAJA U.S.A..A2310BE–A


Keys and doors


HB2034BB


B To raise or lower the moonroof The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause dam- age to the moonroof.


B To open or close the moonroof Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you continue to press on the switch. Release the switch once and push it again to close the moonroof completely. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to prevent water drops from falling into the passenger compartment.


NOTE If the moonroof cannot be closed through the switch operation because of system failure, it can be closed manually using a hex- headed wrench. For the procedure, refer to “Moonroof — if the moonroof cannot be closed” in Chapter 9 “In case of emer-


– CONTINUED –


2-31


BAJA U.S.A..A2310BE–A


gency”.


B Sun shade


OM-H2355


The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.


2-32


BAJA U.S.A..A2310BE–A


Instruments and controls


Ignition switch


Key reminder chime Ignition switch light Key interlock release (AT vehicles only)


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Hazard warning flasher Meters and gauges


Speedometer Odometer/Trip meter Tachometer Outside temperature indicator (if equipped) Fuel gauge Temperature gauge


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Warning and indicator lights


Seatbelt warning light and chime SRS airbag system warning light CHECK ENGINE warning light/Malfunction


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


indicator lamp


Charge warning light Oil pressure warning light AT OIL TEMPerature warning light (for AT vehicles) ABS warning light Brake system warning light Door ajar warning lights Switchback door indicator light Low fuel warning light Front-wheel drive warning light (for AT vehicles) Security system status indicator light (if equipped) Shift position indicator (for AT vehicles) Turn signal indicator lights High beam indicator light Cargo lamp indicator light


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Daytime running light system


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Turn signal lever Illumination brightness control Parking light switch Fog light switch (if equipped) Wiper and washer


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Windshield wiper and washer switches


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Clock Light control switch


3-3
3-5
3-5
3-5
3-6
3-7
3-7
3-7
3-8
3-8
3-9
3-9
3-10
3-10
3-10


3-11
3-12
3-12
3-13
3-13
3-14
3-15
3-15
3-15
3-15
3-16
3-16
3-16
3-16
3-16
3-17
3-17
3-19
3-19
3-20
3-21
3-22
3-22
3-24


BAJA U.S.A..A2310BE–A


Rear window defogger switch Windshield wiper deicer (if equipped) Mirrors


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Inside mirror Outside mirrors


Tilt steering wheel Horn


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


3-26
3-27
3-28
3-28
3-30
3-32
3-33


3-2


BAJA U.S.A..A2310BE–A


Ignition switch


Instruments and controls


WARNING


Never turn the ignition switch to “LOCK” while the vehicle is be- ing driven or towed because that will lock the steering wheel, pre- venting steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.


The ignition switch has four positions: LOCK, ACC, ON and START.


HB4000CA


B LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.


– CONTINUED –


3-3


BAJA U.S.A..A2310BE–A


n Automatic transmission vehicles


HB4016BA


HB2032CA


The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position.


n Manual transmission vehicles


OM-H0144


The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.


B ACC In this position the electrical accessories (radio, cigarette lighter socket, etc.) can be used.


B ON This is the normal operating position after the engine is started.


3-4


BAJA U.S.A..A2310BE–A


Instruments and controls


B START


CAUTION


Do not turn the ignition switch to the “START” position while the engine is running.


The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.


J Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is re- moved from the ignition switch.


J Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened. The light remains on for 10 se- conds and goes out after driver’s door is closed or if the key is turned to the “ON” position.


J Key interlock release (AT vehicles only) If the key can not be turned to the “LOCK” position even when the selec- tor lever is in the “P” position:


HB3011BA


– CONTINUED –


3-5


BAJA U.S.A..A2310BE–A


HB3012BA


OM-H0146


1. Take out the screwdriver from the tool bag. 2. Remove the cover under the steering column using a phillips screwdriver. 3. Turn the ignition key while pressing the key interlock release lever.


Take your vehicle to the nearest SUBARU dealer immediately to have the key interlock system repaired.


Hazard warning flasher


HB8002BA


The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.


3-6


BAJA U.S.A..A2310BE–A


Instruments and controls


To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again.


NOTE When the hazard warning flasher is on, the turn signals do not work.


Meters and gauges


J Speedometer The speedometer shows the vehicle speed.


J Odometer/Trip meter


CAUTION


To ensure safety, do not attempt to change the function of the in- dicator during driving, as an accident could result.


HB3015BB


B Odometer The odometer shows the total distance that the vehicle has been driv- en.


B Double trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero.


– CONTINUED –


3-7


BAJA U.S.A..A2310BE–A


To change the mode indication, briefly push the knob. Each press of the knob changes the function alternately.


A trip meter


B trip meter


To set the trip meter to zero, select either the A trip or B trip meter and push the knob and keep it pushed for more than 1 second.


NOTE If the connection between the combination meter and battery is bro- ken for any reason such as vehicle maintenance or fuse replace- ment, the data recorded on the trip meter will be lost.


J Tachometer


CAUTION


Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.


The tachometer shows the engine speed in thousands of revolutions per minute.


J Outside temperature indicator (if equipped) The outside temperature indicator shows the outside temperature in a range from –22°F to 122°F (–30°C to 50°C).


The indicator can give a false reading under any of the following condi- tions: D When there is too much sun. D During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shutdown. D When the actual outside temperature falls outside the specified indi- cator range.


3-8


BAJA U.S.A..A2310BE–A


Instruments and controls


J Fuel gauge The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ignition switch is in the “ACC” or “LOCK” position.


The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.


J Temperature gauge


CAUTION


If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9.


HB2012BB


The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.


The coolant temperature will vary in accordance with the outside temper- ature and driving conditions.


We recommend that you drive moderately until the pointer of the temper- ature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high rev- ving operation when the engine is not warmed up enough should be


– CONTINUED –


3-9


BAJA U.S.A..A2310BE–A


avoided.


Warning and indicator lights


Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” posi- tion. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:


Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light / Malfunction indicator lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light


If any lights fail to come on, it indicates a burned-out bulb or a malfunc- tion of the corresponding system. Consult your authorized SUBARU dealer for repair.


J Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the reminder chime will sound for about six seconds to remind the driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off automatically after six seconds.


J SRS airbag system warning light AIRBAG When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS frontal airbag and seatbelt pretensioners are in normal operation.


3-10


3


BAJA U.S.A..A2310BE–A


Instruments and controls


If this light comes on while driving or remains illuminated even after a period of about 6 seconds from when the ignition has been turned on, it may indicate that the SRS frontal airbag system or seatbelt pretensioner system is not working properly. Contact your nearest SUBARU dealer im- mediately.


J CHECK ENGINE warning light/Malfunction


indicator lamp


CAUTION


If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.


If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission control system.


B If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been de- tected. You should have your vehicle checked by an authorized SUBARU dealer immediately.


NOTE This light also comes on when the fuel filler cap is not tightened until it clicks.


If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light


– CONTINUED –


3-11


BAJA U.S.A..A2310BE–A


turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately.


B If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the emission control system. To prevent serious damage to the emission control system, you should do the following: D Reduce vehicle speed. D Avoid hard acceleration. D Avoid steep uphill grades. D Reduce the amount of cargo, if possible. D Stop towing a trailer as soon as possible.


The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.


J Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.


If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alterna- tor belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU dealer immediately.


J Oil pressure warning light


CAUTION


Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.


If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working prop- erly.


3-12


BAJA U.S.A..A2310BE–A


Instruments and controls


If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.


J AT OIL TEMPerature warning light


(for AT vehicles)


If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.


If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic.


B Automatic transmission control system warning If the light flashes after the engine starts, it may indicate that the auto- matic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.


(U.S.) J ABS warning light (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.


CAUTION


If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; how- ever, the conventional brake system continues to operate normal- ly. D The warning light does not come on when the ignition switch is turned to the “ON” position. D The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h).


– CONTINUED –


3-13


BAJA U.S.A..A2310BE–A


D The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.


NOTE If the warning light behavior is as shown below, the ABS system may be considered normal. D The warning light comes on right after the engine is started but goes out immediately, remaining off. D The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12
km/h). D The warning light comes on during driving, but it goes out immediately and remains off.


When driving with an insufficient battery voltage such as when the en- gine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.


J Brake system warning light


(U.S.)


(Canada)


WARNING


D Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. D If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.


This light has the following two functions:


B Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is


3-14


3


BAJA U.S.A..A2310BE–A


Instruments and controls


fully released.


B Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released. If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch posi- tioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. Have your vehicle checked by a SUBARU dealer immediately.


J Door ajar warning lights The specific door ajar warning light comes on if any door is not fully closed. Always make sure this light is out before you start to drive.


J Switchback door indicator light While the ignition switch is in the “ON” position, the switchback door indi- cator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” position, the switch- back door indicator light flashes for about 20 seconds and goes off when the switchback door is open.


J Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.6 U.S. gal. (10.0 liters, or 2.2 Imp. gal.). It only operates when the igni- tion switch is in “ON” position. NOTE This light does not go out unless the tank is replenished up to an internal fuel quantity of about 3.7 U.S. gal. (14 liters, 3.1 Imp. gal.).


J Front-wheel drive warning light (for AT vehicles) This light comes on when All Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar


– CONTINUED –


3-15


BAJA U.S.A..A2310BE–A


purposes.


J Security system status indicator light


(if equipped)


This light is found at the bottom center of the combination meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, re- fer to the “Security system” in Chapter 2.


J Shift position indicator (for AT vehicles) This indicator shows the position of the shift lever.


J Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.


J High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.


J Cargo lamp indicator light


CAUTION


Do not switch on the cargo lamp while driving to avoid distract- ing other drivers.


This indicator light shows that the cargo lamp comes on.


3-16


BAJA U.S.A..A2310BE–A


Clock


Instruments and controls


HB2013BA


To set the time, turn the setting knob clockwise to advance and counter- clockwise to retard the time.


Light control switch


WARNING


To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper- ates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.


– CONTINUED –


3-17


BAJA U.S.A..A2310BE–A


HB2007BA


HB2014BB


The light switch operates only when the ignition switch is in the “ON” position.


B Headlights To turn on the headlights, turn the knob on the end of the turn signal lever.


first position


Parking lights, instrument panel illumination, tail lights and license plate light are on.


second position


Headlights, parking lights, instrument panel illumination, tail lights, and license plate light are on.


B High/low beam change (dimmer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indi- cator light “a” on the instrument panel is also on. To switch back to low beam, pull the lever back to the detent position.


B Headlight flasher


CAUTION


Do not hold the lever in the flashing position for more than just a few seconds.


3-18


BAJA U.S.A..A2310BE–A


Instruments and controls


To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” position.


When the headlights are on high beam, the high beam indicator light “a” on the instrument panel also comes on.


J Daytime running light system


WARNING


The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “a” position when it is dark out- side.


The low beam headlights will automatically come on at reduced bright- ness when the engine has started, under the following conditions:


D The parking brake is fully released. D The light switch is in the “OFF” or “p” position.


Turn signal lever


Right turn


Left turn


HB2015BB


To activate the right turn signal, push the turn signal lever up. To activate the left turn signal, push the turn signal lever down. When the turn is fin-


– CONTINUED –


3-19


BAJA U.S.A..A2310BE–A


ished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.


To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.


Illumination brightness control


HB2017BB


When the lighting switch is in the “p” or “a” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.


3-20


BAJA U.S.A..A2310BE–A


Parking light switch


Instruments and controls


HB2018BA


The parking light switch operates regardless of the ignition switch posi- tion.


By pushing the front end of this switch, following lights will come on.


– Parking lights – Front and rear side marker lights – Tail lights – License plate lights


To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.


– CONTINUED –


3-21


BAJA U.S.A..A2310BE–A


Fog light switch (if equipped)


The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off.


HB3020BB


The indicator light located on the switch will illuminate when the fog lights are on.


Wiper and washer


WARNING


In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.


CAUTION


D Do not operate the washer continuously for more than ten se- conds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level fre- quently, such as at fuel stops.


3-22


3


BAJA U.S.A..A2310BE–A


Instruments and controls


D Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. D In freezing weather, be sure that the wiper blades are not fro- zen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to operate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. D If the wipers stop during operation because of ice or some oth- er obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper opera- tion. D Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wiper blades. D Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.


NOTE D The wiper operates only when the ignition switch is in the “ON” or “ACC” position. D Clean your wiper blades and window glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the


– CONTINUED –


3-23


BAJA U.S.A..A2310BE–A


windshield or rear window. D Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. D If you cannot eliminate the streaking even after following this pro- cedure, replace the wiper blades with new ones. Refer to the “Wiper blade replacement” section (chapter 11) for replacement instruc- tions.


J Windshield wiper and washer switches


B Windshield wipers


To turn the wipers on, push the wiper control lever down.


HB3022BB


: Intermittent LO : Low speed HI : High speed


To turn the wipers off, return the lever to the “OFF” position.


3-24


BAJA U.S.A..A2310BE–A


B Wiper intermittent time control


Instruments and controls


HB3024BA


” position, turn the dial to adjust


When the wiper switch is in the “ the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your de- sired interval.


B Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever.


B Washer


To wash the windshield, push the washer button at the end of the wip-


HB3023BA


– CONTINUED –


3-25


BAJA U.S.A..A2310BE–A


er control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button.


Rear window defogger switch


CAUTION


D Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. D To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.


The rear window defogger operates only when the ignition switch is in the “ON” position. The rear window defogger switch is located on the climate control panel.


The defogger will automatically shut off after about 15 minutes. If the win- dow clears before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again.


HB5009BB


To turn on the defogger, push the switch. To turn it off, push the switch again. The indicator light located on the switch lights up while the rear window


3-26


BAJA U.S.A..A2310BE–A


Instruments and controls


defogger is operating.


Windshield wiper deicer (if equipped)


CAUTION


To prevent the battery from being discharged, do not operate the windshield wiper deicer continuously for any longer than neces- sary.


HB3021BB


The windshield wiper deicer operates only when the ignition switch is in the “ON” position.


Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the windshield wiper deicer, push the switch. The indicator light located on the switch lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 min- utes. If the wiper blades have been deiced completely before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the switch to turn the deicer on again.


– CONTINUED –


3-27


BAJA U.S.A..A2310BE–A


Mirrors


Always check that the inside and outside mirrors are properly adjusted before you start driving.


J Inside mirror


HB4003BB


The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.


B Auto-dimming mirror/compass (if equipped)


The auto-dimming mirror/compass has an anti-glare feature which au- tomatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass.


HB6019BB


3-28


BAJA U.S.A..A2310BE–A


Instruments and controls


D By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. D By pressing and releasing the right button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.


Even with the mirror in anti-glare mode, the mirror surface turns bright if the transmission is shifted into reverse. This is to ensure good rear- ward visibility during reversing.


n Photosensors


HB6020BA


The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other simi- lar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator.


n Compass calibration 1. For optimum calibration, switch off all nonessential electrical ac- cessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or


– CONTINUED –


3-29


BAJA U.S.A..A2310BE–A


structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has oc- curred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.


n Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Com- pass calibration zone” map at the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be dis- played. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode.


J Outside mirrors


B Convex mirror (Passenger side)


WARNING


Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of objects that you view in convex mir- ror.


3-30


BAJA U.S.A..A2310BE–A


B Adjusting mirrors To adjust the mirrors by hand, push where indicated by the arrows.


Instruments and controls


OM-H2737


B Remote control mirror switch The remote control mirrors operate only when the ignition switch is in the “ON” or “ACC” position.


HB4004BB


1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation.


The mirrors can also be adjusted manually.


– CONTINUED –


3-31


BAJA U.S.A..A2310BE–A


B Outside mirror defogger (if equipped)


CAUTION


To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.


The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position.


HB4004CB


To turn on the outside mirror defogger, push the switch while the en- gine is running. The indicator light located on the switch will come on when the out- side mirror defogger heater in operation.


To turn it off, push the switch again.


Tilt steering wheel


WARNING


Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.


3-32


BAJA U.S.A..A2310BE–A


Instruments and controls


HB4002BA


1. Adjust the seat position. Refer to the “Front seat” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down.


Horn


To sound the horn, push the horn pad.


OM-H0440


– CONTINUED –


3-33


BAJA U.S.A..A2310BE–A


3-34


BAJA U.S.A..A2310BE–A


Climate control


Ventilator Manual heating and air conditioning system


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Heater operation Air conditioner operation


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


Operating tips for heater and air conditioner Air filtration system (if equipped)


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


. . . . . . . . . . . . . . . . . . .


4-2
4-4
4-7
4-10
4-12
4-13


BAJA U.S.A..A2310BE–A


Ventilator


B Center and side ventilators


B Adjustable side defroster grille (driver’s side – if equipped)


HB5001BB


Normal position


Side defroster grille


Windshield defrost assist position


Fin


HB5002BB


HB5003BB


The driver’s side defroster grille is adjustable. The normal position as shown in the diagram directs warm air to the side glass. When more rapid defrosting of the windshield is desired, the air flow can be directed temporarily toward the windshield to assist the windshield defroster. If this is done, the driver’s side grille should always be returned to its normal position so that the warm air flow can then be used to defrost the driver’s side window.


4-2


BAJA U.S.A..A2310BE–A


B Air flow selection


Climate control


HB5006BA


HB5006DA


HB5006FA


HB5006CA


HB5006EA


– CONTINUED –


4-3


BAJA U.S.A..A2310BE–A


Manual heating and air conditioning system


B Control panel


HB5004BC


1. Temperature control dial 2. Fan speed control dial 3. Air flow control dial 4. Air conditioner button 5. Air inlet selection button 6. Rear window defogger button (Refer to “Rear window defogger” in chapter 3.)


n Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue area (cool) to red area (warm).


n Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds.


n Air flow control dial This dial has the following five positions:


: Air flows through the instrument panel outlets.


: Air flows through the instrument panel outlets and the foot


outlets.


4-4


BAJA U.S.A..A2310BE–A


Climate control


: Air flows through the foot outlets and some through the wind-


shield defroster outlets.


: Air flows through the windshield defroster outlets and foot


outlets.


: Air flows through the windshield defroster outlets.


” or “


NOTE When the dial is placed in the “ ”position, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quickly. At the same time, the air inlet selection is automatically set to “Outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button.


n Air conditioner button


HB5010BB


The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in operation to turn on the air conditioner. The indicator light will come on. Push it again to turn off the air conditioner.


– CONTINUED –


4-5


BAJA U.S.A..A2310BE–A


n Air inlet selection button


WARNING


Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condi- tion clears.


HB5008BB


ON position (Recirculation): Interior air is recirculated inside the ve- hicle. Push the air inlet selection button to the ON position. The indi- cator light will come on. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button again to the OFF position. The indicator light will go off.


4-6


BAJA U.S.A..A2310BE–A


J Heater operation


B Defrosting or defogging the windshield


Climate control


HB5011AA


To direct warm air to the windshield and front door windows: 1. Set the air flow control dial to “ 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed.


”.


NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “


” position.


B Heating and defrosting


HB5012AA


– CONTINUED –


4-7


BAJA U.S.A..A2310BE–A


To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to “ 2. Set the temperature control dial to the desired temperature level. 3. Set the fan speed control dial to the desired speed.


”.


NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “


” position.


B Heating


HB5013AA


To direct warm air toward the floor: 1. Set the air inlet selection button to the “OFF” position 2 Set the air flow control dial to “ 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed.


”.


NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel to the “


” position.


4-8


BAJA U.S.A..A2310BE–A


B Bi-level heating


Climate control


HB5014AA


This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets.

Loading...
x