Login- Download PDF Manual
-
cupant. Do not touch such hot parts until they cool.
B Front seatbelts
OM-H0043
OM-H0044
1. Adjust the seat position: Driver’s seat: Adjust the seatback to the upright position. Move the seatback as far from the steering wheel as practical while still main- taining full vehicle control. Front passenger’s seat: Adjust the seatback to the upright position. Move the seat as far back as possible.
1-18
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
2. Sit well back in the seat. 3. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again. 4. Insert the tongue plate into the buckle until you hear a click. 5. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist.
n Adjusting the front seat shoulder belt anchor height
WARNING
When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision.
HB1029BB
The shoulder belt anchor height should be adjusted to the position best suited for you. To lower the anchor height, push the release but- ton and slide the anchor down. To raise the anchor height, slide the anchor up. Pull down on the anchor to make sure that it is locked in place.
– CONTINUED –
1-19
BAJA U.S.A..A2310BE–A
Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck.
n Unfastening the seatbelt
Push
Push the button on the buckle.
HB0303
Before closing the door, make sure that the belts are retracted prop- erly to avoid catching the belt webbing in the door.
B Rear seatbelts
OM-H0043
OM-H0044
1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving a strong pull on it,
1-20
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
then pull it out slowly again. 3. Insert the tongue plate into the buckle until you hear a click. 4. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist.
n Unfastening the seatbelt
Push
Push the button on the buckle.
HB0303
Before closing the door, make sure that the belts are retracted prop- erly to avoid catching the belt webbing in the door.
J Seatbelt maintenance
CAUTION
D Keep the belts free of polishes, oils, chemicals and particularly battery acid. D Never attempt to make modifications or changes that will pre- vent the seatbelt from operating properly.
To clean the seatbelts, use a mild soap and lukewarm water. Never bleach or dye the belts because this could seriously affect their strength.
Inspect the seatbelts and attachments including the webbing and all hardware periodically for cracks, cuts, gashes, tears, damage, loose bolts or worn areas. Replace the seatbelts even if only minor damage is found.
– CONTINUED –
1-21
BAJA U.S.A..A2310BE–A
Front seatbelt pretensioners
WARNING
D To obtain maximum protection, occupants should sit in an up- right position with their seatbelts properly fastened. Refer to “Seatbelts” section in this chapter. D Do not modify, remove or strike the front seatbelt retractor as- semblies or surrounding area. This could result in accidental ac- tivation of the seatbelt pretensioners or could make the system inoperative, possibly resulting in serious injury. Seatbelt preten- sioners have no user-serviceable parts. For required servicing of front seatbelt retractors equipped with seatbelt pretensioners, see your nearest SUBARU dealer. D When discarding front seatbelt retractor assemblies or scrap- ping the entire car due to collision damage or for other reasons, consult your SUBARU dealer.
Seatbelt retractor assembly (Pretensioner)
HB0373
The driver’s and front passenger’s seatbelts have a seatbelt preten- sioner. The seatbelt pretensioners are designed to be activated in the event of an accident involving a moderate to severe frontal collision.
The pretensioner sensor also serves as a SRS frontal airbag sensor. If the sensor detects a certain predetermined amount of force during a frontal collision, the front seatbelt is quickly drawn back in by the re- tractor to take up the slack so that the belt more effectively restrains
1-22
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
the front seat occupant.
When a seatbelt pretensioner is activated, an operating noise will be heard and a small amount of smoke will be released. These occur- rences are normal and not harmful. This smoke does not indicate a fire in the vehicle.
Once the seatbelt pretensioner has been activated, the seatbelt re- tractor remains locked. Consequently, the seatbelt can not be pulled out and retracted and therefore must be replaced.
NOTE D Seatbelt pretensioners are not designed to activate in minor frontal impacts, in side or rear impacts or in roll-over accidents. D The driver’s seat and passenger’s seat pretensioners and fron- tal airbag operate simultaneously. D Pretensioners are designed to function on a one-time-only ba- sis. In the event that a pretensioner is activated, both the driver’s and front passenger’s seatbelt retractor assemblies must be re- placed and only by an authorized SUBARU dealer. When replac- ing seatbelt retractor assemblies, use only genuine SUBARU parts. D If either front seatbelt does not retract or cannot be pulled out due to a malfunction or activation of the pretensioner, contact your SUBARU dealer as soon as possible. D If the front seatbelt retractor assembly or surrounding area has been damaged, contact your SUBARU dealer as soon as pos- sible. D When you sell your vehicle, we urge you to explain to the buy- er that it has seatbelt pretensioners by alerting the buyer to the contents of this section.
– CONTINUED –
1-23
BAJA U.S.A..A2310BE–A
B System monitors
HB4010EC
A diagnostic system continually monitors the readiness of the seatbelt pretensioner while the vehicle is being driven. The seatbelt preten- sioners share the control module with the airbag system. Therefore, if any malfunction occurs in a seatbelt pretensioner, the SRS airbag sys- tem warning light will illuminate. The SRS airbag system warning light will show normal system operation by lighting for about 6 seconds when the ignition key is turned to the “ON” position.
The following components are monitored by the indicator:
D Front sub sensor (Right hand side) D Front sub sensor (Left hand side) D Airbag control module (including impact sensors) D Seatbelt pretensioner (Driver’s side) D Seatbelt pretensioner (Passenger’s side) D All related wiring
In the event of a malfunction indicated by any of following, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the seatbelt preten- sioners and airbags will not function reliably:
D Flashing or flickering of the indicator light. D No illumination of the warning light when the ignition switch is first turned to the “ON” position. D Continuous illumination of the warning light. D Illumination of the warning light while driving.
1-24
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
B System servicing
WARNING
D When discarding a seatbelt retractor assembly or scrapping the entire car damaged by a collision, consult your SUBARU deal- er. D Tampering with or disconnecting the system’s wiring could re- sult in accidental activation of the seatbelt pretensioner and/or airbag or could make the system inoperative, which may result in serious injury. The wiring harnesses of the seatbelt pretensioner and SRS airbag systems are covered with yellow insulation and the connectors of the system are yellow for easy identification. Do not use electrical test equipment on any circuit related to the seatbelt pretensioner and airbag systems. For required servicing of the seatbelt pretensioner, see your nearest SUBARU dealer.
CAUTION
The front sub sensors are located in both front fenders and the airbag control module including the impact sensors is located under the center console. If you need service or repair in those areas or near the front seatbelt retractors, we recommend that you have an authorized SUBARU dealer perform the work.
NOTE If the front part of the vehicle is damaged in an accident to the extent that the seatbelt pretensioner does not operate, contact your SUBARU dealer as soon as possible.
– CONTINUED –
1-25
BAJA U.S.A..A2310BE–A
B Precautions against vehicle modification
CAUTION
Do not perform any of the following modifications. Such modifi- cations can interfere with proper operation of the seatbelt perten- sioners. D Attachment of any equipment (bush bar, winches, snow plow, skid plate, etc.) other than SUBARU genuine accessory parts to the front end. D Modification of the suspension system or front end structure. D Installation of a tire of different size and construction from the tires specified on the tire placard attached to the door jamb.
Always consult your SUBARU dealer if you want to install any acces- sory parts to your vehicle.
Child restraint systems
WARNING
D Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, because the child will be caught between the passenger and objects inside the vehicle. Additionally, holding a child in your lap or arms in the front seat exposes that child to another serious danger. Since the SRS airbag deploys with con- siderable speed and force, the child could be injured or even killed. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
1-26
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
For that reason, be sure to secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. You should choose a restraint device which is appropriate for the child’s age, height and weight. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. D SINCE YOUR VEHICLE IS EQUIPPED WITH A PASSENGER’S SRS AIRBAG, DO NOT INSTALL A REARWARD FACING CHILD SAFETY SEAT IN THE FRONT PASSENGER’S SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Children should be properly restrained in the rear seat at all times. Never allow a child to stand up, or to kneel on the front passenger’s seat. The SRS airbag deploys with considerable force and can injure or even kill the child.
Never hold a child on your lap or in your arms in the front passenger’s seat or any other seat.
Secure child restraint devices in the REAR seat at all times.
HB0308
HB1117BB
Never install rearward facing child safety seat in the front passen- ger’s seat.
Never allow a child to stand up, or to kneel on the front passenger’s seat or any other seat
HB0306
HB0307
– CONTINUED –
1-27
BAJA U.S.A..A2310BE–A
WARNING
D Child restraint systems and seatbelts can become hot in a ve- hicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. D Do not leave an unsecured child restraint system in your vehi- cle. Unsecured child restraint systems can be thrown around in- side of the vehicle in a sudden stop, turn or accident; it can strike and injure vehicle occupants as well as result in serious injuries or death to the child.
Infants and small children should always be placed in an infant or child restraint system in the rear seat while riding in the vehicle. You should use an infant or child restraint system that meets Federal Motor Vehicle Safety Standards or Canada Motor Vehicle Safety Standards, is compat- ible with your vehicle and is appropriate for the child’s age and size. All child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt (except those cov- ered under the section in this manual, entitled “Installation of child re- straint systems by use of lower and tether anchorages”).
Children could be endangered in an accident if their child restraints are not properly secured in the vehicle. When installing the child restraint system, carefully follow the manufacturer’s instructions.
According to accident statistics, children are safer when properly re- strained in the rear seating positions than in the front seating positions.
All U.S. states and Canadian provinces require that infants and small children be restrained in an approved child restraint system at all times while the vehicle is moving.
1-28
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
B Installing child restraint systems with seatbelt and tether
anchorages
HB1148BA
NOTE When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. The function is restored by retracting the seatbelt fully.
CAUTION
When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child re- straint system, check to ensure that it is held securely in posi- tion. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased.
1. Set the child restraint system in the seating position on the rear seat cushion.
– CONTINUED –
1-29
BAJA U.S.A..A2310BE–A
2. Pull the seatback locking knob and fold the seatback forward to see the tether anchorage on the backside of the seatback.
HB1134BA
HB1144BA
3. Connect the tether belt hook onto the tether anchorage on the backside of the seatback. Take up any slack in the tether belt after connecting it to the tether anchorage.
1-30
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
HB1146BA
4. Put the other end of the tether belt through under the headrest. 5. Return the seatback to the locked position. Confirm that the red mark on the locking knob is no longer visible and check that the seat- back is securely locked by moving it back and forth. 6. Run the lap and shoulder belt through the child restraint system following the instructions provided by its manufacturer.
HB1145BA
HB1148BA
7. Insert the tongue plate into the buckle. 8. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indi- cate the retractor function as ALR. 9. While pushing the child restraint into the seat cushion and moving
– CONTINUED –
1-31
BAJA U.S.A..A2310BE–A
it back and forth, tighten the seatbelt securely by taking up the slack in the belt.
HB1147BA
10. While pushing the child restraint into the seat cushion and moving it back and forth, pull the upper tether belt straight up to secure the child restraint system firmly by taking up the slack in the belt. 11. The loose end of the tether belt should be placed into the gap on the backside of the seatback. 12. To remove the child restraint system, follow the reverse proce- dures of installation. Unbuckle the seatbelt and allow the belt to retract completely. The belt will return to the ELR mode.
If you have any question concerning proper child restraint system installation, ask your SUBARU dealer.
1-32
BAJA U.S.A..A2310BE–A
B Installation of child restraint system by seatbelt only
Seat, seatbelt and SRS airbags
HB1148CA
NOTE When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. The function is restored by retracting the seatbelt fully.
CAUTION
When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in posi- tion. If it is not held tight and secure, the danger of your child suf- fering personal injury in the event of an accident may be increased.
1. Place the child restraint system on the seat. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer.
– CONTINUED –
1-33
BAJA U.S.A..A2310BE–A
HB1145BA
HB1148CA
3. Insert the tongue plate into the buckle. 4. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indi- cate the retractor function as ALR. 5. While pushing the child restraint into the seat cushion and moving it back and forth, tighten the seatbelt securely by taking up the slack in the belt. 6. Before having a child sit in the child restraint system, move it back and forth to check if it is firmly secured. 7. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to ELR mode.
If you have any question concerning proper child restraint system installation, ask your SUBARU dealer.
B Installation of child restraint systems by use of lower and teth-
er anchorages
Some types of child restraint systems can be installed on the rear seat of your vehicle without use of the seatbelts. Such child restraint systems are secured to the dedicated anchorages provided on the vehicle body. The lower and tether anchorages are sometimes re- ferred to as the LATCH system (Lower Anchors and Tethers for CHil- dren).
1-34
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
HB1154BA
Your vehicle is equipped with four lower anchorages (bars) on the back panel behind the markings on the bottom part of the rear seat- back and two upper anchorages (tether anchorages) on the back side of the seatback for accommodating such child restraint systems.
HB11132BA
HB1133BA
The lower anchorages (bars) are used for installing a child restraint system on the rear seat. For each seating position of the rear seat, two lower anchorages are provided. The tether anchorages (upper anchorages) are also provided for each seating position of the rear seat.
You will find marks “ ” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars). Each lower anchorage is located where the seat cushion meets the seatback.
– CONTINUED –
1-35
BAJA U.S.A..A2310BE–A
CAUTION
When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child restraint system, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your child suffering per- sonal injury in the event of an accident may be increased.
1. Place the child restraint system on the rear seat cushion.
2. Unlock the rear seatback locking knob and fold the seatback for- ward to see the tether anchorages on the backside of the seatback.
HB1134BA
HB1144BA
3. Connect the hook of the upper tether belt onto the tether anchor- age on the backside of the seatback. Do not allow slack in the tether belt.
1-36
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
HB1146BA
4. Put the other end of the tether belt through under the headrest. 5. Return the seatback to the locked position. Confirm that the red mark on the locking knob is no longer visible and check if the seat- back has been securely locked by moving it back and forth.
HB1154BA
6. While following the instructions supplied by the child restraint sys- tem manufacturer, connect the lower hooks onto the lower anchor- ages located at “ ” marks on the bottom of the rear seatback. When the hooks are connected, make sure the adjacent seatbelts are not caught.
– CONTINUED –
1-37
BAJA U.S.A..A2310BE–A
HB1131BA
7. [If your child restraint system is of a flexible attachment type (which uses tether belts to connect the child restraint system properly to the lower anchorages)] While pushing the child restraint into the seat cushion, pull both left and right lower tether belts up to secure the child restraint system firmly by taking up the slack in the belt.
HB1147BA
8. Pull the upper tether belt straight up to secure the child restraint system firmly by taking up the slack in the belt. 9. Put the loose end of the tether belts behind the seatback. 10. To remove the child restraint system, follow the reverse proce- dures of installation.
If you have any question concerning proper child restraint system installation, ask your SUBARU dealer.
1-38
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
*SRS airbag (Supplemental Restraint System airbag)
*SRS: This stands for supplemental restraint system. This name is used because the airbag system supplements the vehicle’s seatbelts.
J Vehicle with driver’s and front passenger’s SRS air-
bags and lap/shoulder restraints
WARNING
D To obtain maximum protection in the event of an accident, the driver and all passengers in the vehicle should always wear seat- belts when the vehicle is moving. The SRS airbag is designed only as a supplement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. In combination with the seatbelts, it offers the best combined protection in case of a serious accident. Not wearing a seatbelt increases the chance of severe injury or death in a crash even when the car has the SRS airbag. For instructions and precautions concerning the seatbelt system, see the “Seatbelts” sections in this chapter. D Do not sit or lean unnecessarily close to the SRS airbag. Be- cause the SRS airbag deploys with considerable speed – faster than the blink of an eye – and force to protect in high speed colli- sions, the force of an airbag can injure an occupant whose body is too close to SRS airbag. It is also important to wear your seatbelt to help avoid injuries that can result when the SRS airbag contacts an occupant not in proper position such as one thrown forward during pre-accident braking. Even when properly positioned, there remains a possibility that an occupant may suffer minor injury such as abrasions and bruises to the face or arms because of the SRS airbag deploy- ment force.
– CONTINUED –
1-39
BAJA U.S.A..A2310BE–A
D The SRS airbags deploy with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. D Do not place any objects over or near the SRS airbag cover or between you and the SRS airbag. If the SRS airbag deploys, those objects could interfere with its proper operation and could be propelled inside the car and cause injury. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater. For that reason, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropriate for the child’s age, height and weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning the child restraint system, see the “Child restraint systems” section in this chapter. D NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Never allow a child to stand up, or to kneel on the front pas- senger’s seat, or never hold a child on your lap or in your arms.
1-40
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
The SRS airbag deploys with considerable force and can injure or even kill the child.
Put children in the REAR seat prop- erly restrained at all times.
HB0291
CAUTION
D When the SRS airbag deploys, some smoke will be released. This smoke could cause breathing problems for people with a history of asthma or other breathing trouble. If you or your pas- sengers have breathing problems after SRS airbag deploys, get fresh air promptly. D A deploying SRS airbag releases hot gas. Occupants could get burnt if they come into direct contact with the hot gas.
Your vehicle is equipped with a supplemental restraint system in addition to a lap/shoulder belt at each front seating position. The supplemental restraint system (SRS) consists of two airbags (driver’s and front passenger’s frontal airbags). These SRS airbags are designed only as a supplement to the prima- ry protection provided by the seatbelt.
The system also controls front seatbelt pretensioners. For operation, instructions are precautions concerning the seatbelt pretensioner, see the “Front seatbelt pretensioner” section in this chapter.
– CONTINUED –
1-41
BAJA U.S.A..A2310BE–A
NOTE When you sell your vehicle, we urge you to explain to the buyer that it is equipped with SRS airbags by alerting him to the applicable section in this owner’s manual.
B Components
HB1135BB
1 Airbag control module
(including impact sensors)
2 Airbag module (driver’s side) 3 Airbag module
(passenger’s side) 4 Front sub sensor
(left hand side)
5 Front sub sensor (right hand side)
6 Seatbelt pretensioner
(driver’s side)
7 Seatbelt pretensioner
(passenger’s side)
1-42
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
J SRS frontal airbag
WARNING
D NEVER INSTALL A REARWARD FACING CHILD SAFETY SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Never allow a child to stand up, or to kneel on the front pas- senger’s seat, or never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. D The SRS airbag deploys with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. It is also important to wear your seatbelt to help avoid injuries that can result when the SRS airbag contacts an occupant not in proper position such as one thrown toward the front of the car during pre-accident braking.
Never install rearward facing child restraint system in the front passen- ger’s seat.
Never allow a child to stand up, or to kneel on the front passenger’s seat
HB0306
HB0307
– CONTINUED –
1-43
BAJA U.S.A..A2310BE–A
Never hold a child on your lap or in your arms.
Adjust the seatback to upright position. Sit well back and upright.
HB0308
Move the seat as far from the steering wheel as practical.
HS0233
Adjust the seatback to upright position. Sit well back and upright.
Move the seat as far back as possible.
HB0290
WARNING
D Do not put any objects over the steering wheel pad and dash- board. If the SRS frontal airbag deploys, those objects could in- terfere with its proper operation and could be propelled inside the vehicle and cause injury. D Do not attach accessories to the windshield, or fit an extra- wide mirror over the rear view mirror. If the SRS airbag deploys, those objects could become projectiles that could seriously in- jure vehicle occupants.
1-44
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
HB1047BB
The driver’s SRS frontal airbag is stowed in the center portion of the steering wheel. The passenger’s SRS frontal airbag is stowed near the top of the dashboard under an “SRS AIRBAG” mark.
In a moderate to severe frontal collision, the driver’s and front passen- ger’s SRS frontal airbags deploy and supplement the seatbelts by reduc- ing the impact on the driver’s and front passenger’s head and chest.
B Operation
CAUTION
Do not touch the SRS airbag system components around the steering wheel and dashboard with bare hands right after deploy- ment. Doing so can cause burns because the components can be very hot as a result of deployment.
– CONTINUED –
1-45
BAJA U.S.A..A2310BE–A
Driver’s side
Passenger’s side
SRS airbags deploy as soon as a collision occurs.
After deployment, SRS airbags start to deflate immediately so that the driver’s vision is not obstructed.
OM-H0384
The SRS airbag can function only when the ignition switch is in the “ON” position. If the front sub sensors inside the both front fenders and the impact sensors in the airbag control module detect a certain predetermined amount of force during a frontal collision, the control module sends signals to the frontal airbag modules instructing them to inflate the SRS frontal airbags. Then both airbag modules produce gas, which instantly inflates driver’s and passenger’s SRS frontal airbags. After the deployment, the SRS airbags immediately start to deflate so that the driver’s vision is not obstructed. The time required from detecting impact to the deflation of the SRS airbag after deployment is shorter than the blink of an eye. The front passenger’s SRS frontal airbag deploys together with driv- er’s SRS frontal airbag even when no one occupies the front passen- ger’s seat. When the SRS frontal airbags deploy, the driver’s and front passen- ger’s seatbelt pretensioners operate at the same time. Although it is highly unlikely that the SRS airbag would activate in a non-accident situation, should it occur, the SRS airbag will deflate quickly, not obscuring vision and will not interfere with the driver’s ability to maintain control of the vehicle.
1-46
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
When the SRS airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are normal result of the deployment. This smoke does not indicate a fire in the vehicle.
The SRS frontal airbag is designed to deploy in the event of an acci- dent involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts because the necessary protection can be achieved by the seatbelt alone. Also, it is basically not designed to deploy in side or rear impacts or in roll-over acci- dents because deployment of the SRS frontal airbag would not help the occupant in those situations. The SRS airbag is designed to func- tion on a one-time-only basis.
SRS airbag deployment depends on the level of force experienced in the passenger compartment during a collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself.
n Examples of accident in which the SRS frontal airbag will most
likely deploy.
A head-on collision against a thick concrete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) or higher activates the SRS frontal air- bag. The SRS frontal airbag will also be activated when the vehicle is exposed to a frontal impact similar in fashion and magnitude to the above-mentioned collision.
HB1136BA
– CONTINUED –
1-47
BAJA U.S.A..A2310BE–A
n Examples of the types of accidents in which it is possible that
the SRS frontal airbag will deploy.
The SRS frontal airbag may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely bumped or knocked hard against an obstacle on the road such as a curb).
HB1137BA
HB1138BA
n Examples of the types of accidents in which the SRS frontal
airbag is unlikely to deploy.
There are many types of collisions which might not necessarily require SRS frontal airbag deployment. If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset frontal impact, the SRS frontal airbag may not deploy depending on the level of accident forces in- volved.
HB1041AB
HB1139BB
HB1142BB
1-48
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
n Examples of the types of accidents in which the SRS frontal
airbag will basically not deploy.
The SRS frontal airbag is basically not designed to deploy if the vehicle is struck from side or from behind, or if it rolls onto its side or roof, or if it is involved in a low-speed frontal collision.
HB1140BB
HB1141BB
HB1044AB
In an accident where the vehicle is impacted more than once, the SRS frontal airbag deploys only once. Example: In the case of a double collision, first with another vehicle, then against a concrete wall in immediate succession, once the SRS frontal airbag is activated on the first impact, it will not be activated on the second.
HB1143BB
– CONTINUED –
1-49
BAJA U.S.A..A2310BE–A
J SRS airbag system monitors
HB4010EC
A diagnostic system continually monitors the readiness of the SRS air- bag system (including front seatbelt pretensioners) while the vehicle is being driven. The SRS airbag system warning light “AIRBAG” will show normal system operation by lighting for about 6 seconds when the igni- tion key is turned to the “ON” position.
The following components are monitored by the indicator:
D Front sub sensor (Right hand side) D Front sub sensor (Left hand side) D Airbag control module (including impact sensors) D Frontal airbag module (Driver’s side) D Frontal airbag module (Passenger’s side) D Seatbelt pretensioner (Driver’s side) D Seatbelt pretensioner (Passenger’s side) D All related wiring
In the event of a malfunction indicated by any of following, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the SRS airbags will not function reliably: D Flashing or flickering of the indicator light. D No illumination of the warning light when the ignition switch is first turned to “ON” position. D Continuous illumination of the warning light.
1-50
1
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
D Illumination of the warning light while driving.
J SRS airbag system servicing
WARNING
D When discarding an airbag module or scrapping the entire car damaged by a collision, consult your SUBARU dealer. D The SRS airbag has no user-serviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your near- est SUBARU dealer. Tampering with or disconnecting the sys- tem’s wiring could result in accidental inflation of the SRS airbag or could make the system inoperative, which may result in seri- ous injury. The wiring harnesses of the SRS airbag system are covered with yellow insulation and system connectors are yellow for easy identification.
CAUTION
If you need service or repair in areas listed below, we recommend that you have an authorized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas.
D Under the center console D Inside each front fender D Steering wheel and column and nearby areas D Top of the dashboard on front passenger’s side and nearby areas D Inside each center pillar
In the event that the SRS airbag is deployed, replacement of the sys- tem should be performed only by an authorized SUBARU dealer. When the components of the SRS airbag system are replaced, use only genuine SUBARU parts.
To ensure their long-term reliability, the SRS airbags must be inspected
– CONTINUED –
1-51
BAJA U.S.A..A2310BE–A
by a SUBARU dealer ten years after the date of manufacture, which is shown on the certification label attached to the driver’s door.
NOTE In the following cases, contact your SUBARU dealer as soon as pos- sible.
D The front part of the vehicle was involved in an accident in which the SRS frontal airbags did not deploy. D The pad section of the steering wheel or front passenger’s frontal airbag cover is scratched, cracked, or otherwise damaged.
J Precautions against vehicle modification
WARNING
D To avoid accidental activation of the system or rendering the system inoperative, which may result in serious injury, no modifi- cations should be made to any components or wiring of the SRS airbag system. This includes following modifications: D Installation of custom steering wheels D Attachment of additional trim materials to the dashboard D Installation of additional electrical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could interfere with proper operation of the SRS airbag system.
CAUTION
Do not perform any of the following modifications. Such modifi- cations can interfere with proper operation of the SRS airbag sys- tem. D Attachment of any equipment (brush bar, winches, snow plow, skid plate, etc.) other than SUBARU genuine accessory parts to the front end. D Modification of the suspension system or front end structure.
1-52
BAJA U.S.A..A2310BE–A
Seat, seatbelt and SRS airbags
D Installation of a tire of different size and construction from the tires specified on the tire placard attached to the driver’s door jamb.
Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle.
– CONTINUED –
1-53
BAJA U.S.A..A2310BE–A
1-54
BAJA U.S.A..A2310BE–A
Keys and doors
Keys Door locks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power door locking switches
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote keyless entry system (if equipped)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle finder function
Security system (if equipped) Child safety locks Windows
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate
License plate bracket
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switchback door
Switchback door indicator light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moonroof
Tilting/sliding moonroof
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2
2-3
2-5
2-6
2-8
2-13
2-20
2-21
2-21
2-23
2-24
2-26
2-29
2-30
2-30BAJA U.S.A..A2310BE–A
Keys
Master key
Submaster key
Valet key
Key number plate
HS0009
Three types of keys are provided for your vehicle. Master key, submaster key and valet key.
The master key and submaster key fit all locks on your vehicle.
D Ignition switch D Doors D Glove box
The valet key fits only the ignition switch and door locks. You can keep glove box locked when you leave your vehicle and valet key at a parking facility.
B Key number The key number is stamped on the metal plate attached to the key set. Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.
2-2
BAJA U.S.A..A2310BE–A
Door locks
B Locking and unlocking from the outside
Keys and doors
OM-H2394
To lock the door from the outside with the key, insert the key into the keyhole and turn the key toward the rear. To unlock the door, turn the key toward the front.
Lift the outside door handle to open an unlocked door.
HB2024BD
HB2024CB
To lock the door from the outside without the key, rotate the lock lever rearward and then close the door.
To lock the door from the outside using the power door locking switch, push the switch forward (“LOCK” side) and then close the door. In this case, all closed doors are locked at the same time.
– CONTINUED –
2-3
BAJA U.S.A..A2310BE–A
Always make sure that all doors are locked before leaving your vehicle.
NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside without the key.
B Locking and unlocking from the inside
WARNING
Keep all doors locked when you drive, especially when small chil- dren are in your vehicle. Along with the proper use of seat belts and child restraints, lock- ing the doors reduces the chance of being thrown out of the ve- hicle in an accident. It also helps prevent passengers from falling out if a door is acci- dentally opened, and intruders from unexpectedly opening doors and entering your vehicle.
HB2001BB
To lock the door from the inside, rotate the lock lever rearward. To un- lock the door from the inside, rotate the lock lever forward.
The red mark on the lock lever appears when the door is unlocked. Pull the inside door handle to open an unlocked door. Always make sure that all doors are closed and locked before starting to drive.
2-4
BAJA U.S.A..A2310BE–A
J Power door locking switches
Keys and doors
HB2008CB
HB2009BB
All doors can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.
To lock the doors, push the switch forward. To unlock the doors, push the switch rearward.
When you close the doors after you set the door locks, the doors remain locked.
NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using power door locking switches.
– CONTINUED –
2-5
BAJA U.S.A..A2310BE–A
Remote keyless entry system (if equipped)
CAUTION
D Do not expose the transmitter to severe shocks, such as those experienced as a result of dropping or throwing. D Do not take the transmitter apart except when replacing the battery. D Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Two transmitters are provided for your vehicle.
The keyless entry system has the following functions. D Locking and unlocking the doors without a key D Sounding a panic alarm D Arming and disarming the security system (if your vehicle is equipped with an optional security system). See the next section “Security system (if equipped)” for detailed information.
The operable distance of the keyless entry system is approximately 30
feet (10 meters). However, this distance will vary depending on environ- mental conditions. Range may be reduced near sources of RF interfer- ence such as power plants and radio/television broadcasting towers.The keyless entry system does not operate when the key is inserted in the ignition switch.
2-6
BAJA U.S.A..A2310BE–A
Keys and doors
HB1000BF
B Locking the doors Briefly press the “LOCK/ARM” button (for less than two seconds) to lock all doors. An electronic chirp will sound one time and the turn signal lights will flash one time. If any of the doors is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors are not properly closed. When you close the door, it will automatically lock.
NOTE If the “LOCK/ALARM” button is pressed for two seconds or long- er, the panic alarm will sound. When locking the doors in normal circumstances, press the “LOCK/ALARM” button for less than two seconds. For details on the panic alarm, refer to “Sounding the panic alarm”.
B Unlocking the doors Briefly press the “UNLOCK/DISARM” button (for less than two seconds) to unlock the driver’s door. An electronic chirp will sound two times and the turn signal lights will flash two times. To unlock all doors, briefly press the “UNLOCK/DISARM” button a second time within 5 seconds.
NOTE If the interval between the first and second presses of the “UN-
– CONTINUED –
2-7
BAJA U.S.A..A2310BE–A
LOCK/DISARM” button (for unlocking of all of the doors is ex- tremely short, the system may not respond.
B Illuminated entry The interior (dome) light will illuminate when the “UNLOCK/DISARM” button is pressed. These lights stay illuminated for approximately 30
seconds if any of the doors is not opened. If the “LOCK/ARM” button is pressed before 30 seconds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light must be set to the middle position in order for this function to operate.J Vehicle finder function Use this functon to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the ve- hicle, pressing the “LOCK/ARM” button three times in a five-second peri- od will cause your vehicle’s horn to sound one time and its turn signal lights to flash three times.
B Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30 seconds.
B Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If desired, you may turn the audible signal off. To turn the audible signal off, unlock the doors by pushing “UNLOCK/ DISARM” button and then simultaneously depress “LOCK/ARM” and “UNLOCK/DISARM” buttons for more than two seconds. An electronic chirp will sound two times and the turn signal lights will flash two times to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the doors by pushing “UNLOCK/
2-8
BAJA U.S.A..A2310BE–A
Keys and doors
DISARM” button and then simultaneously depress “LOCK/ARM” and “UNLOCK/DISARM” buttons for more than two seconds. An electronic chirp will sound one time and the turn signal lights will flash one time to inform you that the audible signal has been turned on.
B Replacing the battery
CAUTION
Do not let dust, oil or water get on or in the transmitter when replacing the battery.
When the transmitter battery begins to get weak, transmitter range will begin to decrease and the LED will not illuminate. Replace the battery as soon as possible.
Positive (+) side facing up
HB1001BA
HB1002BB
To replace the battery: 1. Remove the two screws on the back of the transmitter case by using a phillips screwdriver. 2. Separate the case. 3. Remove the old battery from the holder. 4. Replace with a new battery (Type CR2032 or equivalent) making sure to install the new battery with the positive (+) side facing up. 5. Install the back half of the transmitter case. 6. Reinstall the two screws on the back of the transmitter case. After the battery is replaced, the transmitter must be synchro- nized with the keyless entry system’s control unit. Press either
– CONTINUED –
2-9
BAJA U.S.A..A2310BE–A
the “LOCK/ARM” or “UNLOCK/DISARM” button six times to syn- chronize the unit.
B Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system.
n Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the sys- tem or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or dif- ferent.
To enter the programming mode:
1 Press to dis- arm the security system (if so equipped).
HB1000CB
HB1005BC
1. Disarm the security system. (if your vehicle is equipped with the optional security system.) 2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.
2-10
BAJA U.S.A..A2310BE–A
Keys and doors
HB2032BB
4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15 seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode.
NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this procedures.
To program the transmitters:
3 Press any button.
HB1005BB
HB1000DB
1. Open the driver’s door. 2. Close the driver’s door. 3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound two times to indicate
– CONTINUED –
2-11
BAJA U.S.A..A2310BE–A
that the transmitter has been programmed.
Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter.
To exit the programming mode: 1. After all of your transmitters are programmed, remove the key from the ignition switch. The horn will sound three times to indicate that the system has exited the programming mode. 2. Make sure that the keyless entry system properly operates by operating each transmitter.
n Deleting old transmitter codes The control unit of the keyless entry system has four memory loca- tions to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code remains in the memory. For security reasons, lost transmitter codes should be deleted from the memory. To delete old transmitter codes, program four transmitter codes into the system. If you have only one current transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory.
NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their trans- mitter code will be programmed into your system, allowing them unauthorized access to your vehicle.
2-12
BAJA U.S.A..A2310BE–A
Keys and doors
Security system (if equipped)
The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key.
The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch.
B System operation The security system will give the following alarm indications when trig- gered: D The turn signal lights will flash and the horn will sound intermit- tently. In addition, the starter motor will not operate. D The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tampered with again. The alarm will continue for six times if any sensor continues to be activated.
The alarm is triggered by: D Opening a door. D Application of physical shock to the vehicle (e.g. breaking glass or forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher lev- els of shock are detected and the system will go into full alarm. D Ignition switch being turned on while in armed state.
NOTE D The alarm will not be triggered by opening the switchback door. D The alarm may not be triggered when the window is broken with a sharp-edged tool. D With the valet mode selected, the security system does not op- erate and the turn signal lights do not flash when the remote
– CONTINUED –
2-13
BAJA U.S.A..A2310BE–A
transmitter is used for locking and unlocking. The security system indicator light in the combination meter flashes twice per second to show that the valet mode is selected. For details, refer to “Valet mode” in this section.
B Arming the system n To arm the system using remote transmitter
Press to Disarm the system.
Press to Arm the system.
HB1000EB
HB2033BB
1. Close all windows and moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close all doors. 6. Briefly press the “LOCK/ARM” button (for less than two seconds). All doors will lock, an electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light starts flashing slowly (approximately once every two seconds).
If any of the doors (except the switchback door) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors are not properly closed. When you close the door, the system will automatically arm and doors will auto- matically lock.
2-14
BAJA U.S.A..A2310BE–A
n To arm the system using power door locking switches
Keys and doors
HB2024CC
1. Close all windows and the moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood and switchback door are locked. 5. Close the doors but leave only the driver’s door or the front pas- senger’s door open. 6. Push the power door locking switch forward (“LOCK” side) to set the door locks. 7. Close the door. An electronic chirp will sound one time, the turn signal lights will flash one time and the indicator light will start flashing slowly (approximately once every two seconds) to inform you that the system has armed.
NOTE The system can be armed even if the engine hood, the windows, the switchback door and/or moonroof are open. Always make sure that they are fully closed before arming the system.
B Disarming the system Briefly press the “UNLOCK/DISARM” button (for less than two seconds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound two times, the turn signal lights will flash two times and the indicator light will go off.
To unlock all other doors, briefly press the “UNLOCK/DISARM” button
– CONTINUED –
2-15
BAJA U.S.A..A2310BE–A
a second time.
n Emergency disarming If you cannot disarm the system using the transmitter (i.e. the trans- mitter is lost, broken or the transmitter battery is too weak), you can disarm the system without using the transmitter.
To disarm the system: 1. Unlock the door with the key and then open the door. 2. The alarm will sound. 3. Insert the key into the ignition switch and cycle it from “LOCK” to “ON” three (3) times within 5 seconds.
B Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM” button pressed for more than two seconds. The horn will sound and the turn signal lights will flash. To deactivate it, press the “LOCK/ARM” button or “UNLOCK/DISARM” button. Unless a button on the remote is pressed, the alarm will be deacti- vated after approximately 30 seconds.
B Valet mode When you choose the valet mode, the security system does not oper- ate. In valet mode, the remote transmitter is used only for locking and unlocking the doors and panic activation.
To enter the valet mode, open the driver’s door and keep the “UNLOCK/DISARM” button depressed for more than two seconds. The security system indicator light will continue to flash 2 times per second indicating that the system is in the valet mode.
To exit valet mode, open the driver’s door and keep the “UNLOCK/ DISARM” button pressed for more than two seconds. The indicator will stop flashing.
B Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the
2-16
BAJA U.S.A..A2310BE–A
Keys and doors
remote transmitter. Note that in this mode, DOORS MUST BE MANU- ALLY LOCKED.
n To enter the passive mode
WARNING
Do not disconnect or tamper with any yellow connector and/or any harness covered with yellow insulation and/or tape. Doing so could result in accidental inflation of the SRS airbag or could make the SRS airbag system inoperative, which may result in serious injury.
HB2036BA
HB2038BB
1. Remove the side sill cover on the driver’s side.
1) Open the driver’s door. 2) Remove the two clips fastening the front portion of the cover with a screwdriver. 3) Remove the side sill cover by pulling it up.
2. Connect the white (1 pole) connector. 3. Turn the ignition switch from “LOCK” to “ON”. 4. Install the side sill cover.
To place the system in active arming mode (remote required for ac- tivation), disconnect the white connector.
– CONTINUED –
2-17
BAJA U.S.A..A2310BE–A
n Arming the system
CAUTION
In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.
HB2031BB
HB2024DB
1. Turn the ignition switch to “ON”. 2. Turn the ignition switch from “ON” to “LOCK” and remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after one min- ute.
In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arm- ing will take place immediately regardless of whether or not the pas- sive mode has been selected.
B Disarming the system To disarm the system, briefly press the “UNLOCK/DISARM” button on
2-18
BAJA U.S.A..A2310BE–A
Keys and doors
the transmitter.
B Tripped sensor identification If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the system, this indicates that the alarm was triggered. The number of times the indicator light flashes indi- cates what sensor caused the alarm condition.
To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to “ON” two times. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.
The indicator light provides the following indications. Flashing one time: Any door has been opened. Flashing three times: The impact sensor in the system’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected.
NOTE The battery must be reconnected before the indicator light will flash.
To exit this mode, close the door and turn the ignition switch to “ON”.
– CONTINUED –
2-19
BAJA U.S.A..A2310BE–A
Child safety locks
WARNING
Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.
HB2002BB
Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.
When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.
2-20
BAJA U.S.A..A2310BE–A
Windows
J Power windows
Keys and doors
WARNING
To avoid serious personal injury caused by entrapment, you must observe the following warnings: D When operating power windows, be extremely careful to pre- vent anyone’s fingers, arms or head from being caught in the window. D Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.
The power windows operate only when the ignition switch is in the “ON” position.
B Driver’s side switches
HB2008BB
– CONTINUED –
2-21
BAJA U.S.A..A2310BE–A
HB2008DB
All door windows can be controlled by the power window switch clus- ter at the driver side door.
n Operating the driver’s window To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up lightly.
To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held.
n Operating the passengers’ windows To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired posi- tion.
n Locking the passengers’ windows To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.
2-22
BAJA U.S.A..A2310BE–A
B Passengers’ side switches
Keys and doors
HB2009CB
HB2005BB
To open the window, push the switch down and hold it until the win- dow reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position.
When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ win- dows cannot be operated with the passengers’ switches.
Tailgate
CAUTION
Keep the tailgate closed when the vehicle is moving. If you must drive with the tailgate open, use the optional Subaru Bed Extender and place the License Plate Bracket at its fully lowered/ open position. Cargo must not stick out beyond the Extender. Otherwise a dangerous road hazard or personal injury could result.
– CONTINUED –
2-23
BAJA U.S.A..A2310BE–A
HB2050BA
Before opening the tailgate, remove any object on the upper surface of the rear bumper to avoid damaging the tailgate. To open the tailgate, lift up on its handle while pulling the tailgate toward you. The support cables hold the tailgate open.
See “Loading your vehicle” section in Chapter 8 for precautions in load- ing cargo.
To close the tailgate, firmly push it upward until it latches.
After you put the tailgate back up, pull it back toward you to be sure it latches securely.
J License plate bracket
When you drive with the tailgate open and with the bed extender used,
HB2051BA
2-24
BAJA U.S.A..A2310BE–A
Keys and doors
the license plate bracket must be placed at its fully lowered/open posi- tion to make the rear license plate visible.
CAUTION
In order to avoid damaging the license plate bracket or the bum- per, the license plate bracket must be in its fully lowered/open position before the tailgate is lowered.
HB2054BA
HB2053BA
To use the license plate bracket at its lowered/open position, push the two release buttons and pull the license plate bracket up until it clicks. And then open the tailgate. If your vehicle is equipped with a trailer hitch, remove the ball mount from the hitch receiver tube before opening the tailgate. Failure to follow this procedure could result in damage to the license plate bracket. When you drive with the tailgate closed, the license plate bracket must be restored to its original position. To restore the license plate bracket to its original position, close the tail- gate, and then pull the license plate bracket down until it clicks. If the license plate bracket is hard to be restored to its original position, mud may have accumulated on the back of the license plate bracket. Remove accumulated mud before pulling the license bracket down.
– CONTINUED –
2-25
BAJA U.S.A..A2310BE–A
CAUTION
In order to avoid damaging the license plate bracket or the bum- per, the license plate bracket must be restored to its original posi- tion until it clicks.
Switchback door
HB2052BA
With the switchback door open, you can increase the usable cargo space and can carry long objects.
WARNING
Secure long objects properly to prevent them from sliding for- ward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equiv- alent.
CAUTION
Pay attention that your fingers do not get pinched with the switchback door when opening and closing it.
2-26
BAJA U.S.A..A2310BE–A
To open the switchback door:
Keys and doors
HB1112BA
1. Pull up the rear seat cushion. Refer to “Rear seats” section in Chapter 1 for operating details.
HB1112CB
HB1113BA
2. Unlock the rear seatback by pulling up on the knob and fold down the rear seatback. Confirm that the pins located at the bottom of the seat cushion is inserted into the slots at the top of the seatback.
– CONTINUED –
2-27
BAJA U.S.A..A2310BE–A
HB1114BA
HB1115BA
3. Fold down the switchback door by releasing the lock knob. Then you can have a flat and larger cargo space. 4. Place the long object on the cargo bed through the switchback door opening. Be sure all items are secured in place. NOTE D When opening the switchback door in snow, accumulated snow in the cargo bed may enter the passenger compartment which could result in dampness in the passenger compartment. Prior to opening of the switchback door, brush off the snow completely. D Close the switchback door whenever you leave the vehicle to pre- vent unauthorized entry.
WARNING
The switchback door should be kept completely shut when the vehicle is idling in an enclosed or partially enclosed area to avoid the possibility of exhaust gas entering the passenger compart- ment. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is extremely dangerous, or even lethal if inhaled. To ensure that exhaust gas cannot penetrate the switch- back door, make certain that there are no obstructions between the door and the vehicle body that prevent the door from fully closing or that crimp the weather strip around the door.
2-28
BAJA U.S.A..A2310BE–A
To close the switchback door, firmly push it upward until it latches. Return the seatback and seat cushion to their original positions and make sure they are securely locked.
Keys and doors
CAUTION
After returning the seatback to its original position, make sure that the rear seatback has been securely locked. When securely locked, the red marks on the locking knobs are no longer visible.
J Switchback door indicator light
HB4010JA
While the ignition switch is in the “ON” position, the switchback door indi- cator light comes on when the switchback door is open. While the ignition switch is in the “LOCK” or “ACC” position, the switch- back door indicator light flashes for about 20 seconds and goes off when the switchback gate is open.
– CONTINUED –
2-29
BAJA U.S.A..A2310BE–A
Moonroof
WARNING
Never let anyone’s hands, arms, head or any objects protrude from the moonroof. He/she could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is in- volved in an accident.
To avoid serious personal injury caused by entrapment, you must observe the following warnings: D Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.
CAUTION
D Do not sit on the edge of the open moonroof. D Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
J Tilting/sliding moonroof The moonroof has both tilting and sliding functions. The moonroof operates only when the ignition switch is in the “ON” posi- tion.
2-30
BAJA U.S.A..A2310BE–A
Keys and doors
HB2034BB
B To raise or lower the moonroof The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause dam- age to the moonroof.
B To open or close the moonroof Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway if you continue to press on the switch. Release the switch once and push it again to close the moonroof completely. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to prevent water drops from falling into the passenger compartment.
NOTE If the moonroof cannot be closed through the switch operation because of system failure, it can be closed manually using a hex- headed wrench. For the procedure, refer to “Moonroof — if the moonroof cannot be closed” in Chapter 9 “In case of emer-
– CONTINUED –
2-31
BAJA U.S.A..A2310BE–A
gency”.
B Sun shade
OM-H2355
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
2-32
BAJA U.S.A..A2310BE–A
Instruments and controls
Ignition switch
Key reminder chime Ignition switch light Key interlock release (AT vehicles only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hazard warning flasher Meters and gauges
Speedometer Odometer/Trip meter Tachometer Outside temperature indicator (if equipped) Fuel gauge Temperature gauge
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and indicator lights
Seatbelt warning light and chime SRS airbag system warning light CHECK ENGINE warning light/Malfunction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
indicator lamp
Charge warning light Oil pressure warning light AT OIL TEMPerature warning light (for AT vehicles) ABS warning light Brake system warning light Door ajar warning lights Switchback door indicator light Low fuel warning light Front-wheel drive warning light (for AT vehicles) Security system status indicator light (if equipped) Shift position indicator (for AT vehicles) Turn signal indicator lights High beam indicator light Cargo lamp indicator light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
