Login- Download PDF Manual
-
page 1-41.
Instrument Panel
3-25
{ CAUTION
If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.
The airbag readiness light comes on when the vehicle is started, and flashes for a few seconds. The light goes out when the system is ready.
3-26
Instrument Panel
If the airbag readiness light stays on after the vehicle is started or comes on while driving, the airbag system may not work properly. Have the vehicle serviced right away. The airbag readiness light should flash for a few seconds when the engine is started. If the light does not come on then, have it fixed immediately. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message may also come on. See DIC Warnings and Messages on page 3-42 for more information.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-49
for important safety information. The instrument panel has a passenger airbag status indicator.United States
Canada
When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF,
or either the on or off symbol to let you know the status of the right front passenger frontal and seat-mounted side impact airbags. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger frontal airbag and seat-mounted side impact airbag are enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service.
{ CAUTION
If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-25 for more information, including important safety information.
Charging System Light
If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer/retailer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.
Brake System Warning Light
The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. It should go out when the engine is started.
United States Canada The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. When the ignition is on, the brake system warning light comes on when the parking brake is set. The
Instrument Panel
3-27
light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, there is a brake problem. Have the brake system inspected immediately.
{ CAUTION
The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-22.
3-28
Instrument Panel
Antilock Brake System (ABS) Warning Light
For vehicles with the Antilock Brake System (ABS), this light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer. If the ABS light stays on longer than a few seconds after engine is started, or comes on and stays on while driving, try resetting the system. To reset the system: 1. While driving, pull over when it is
safe to do so.
2. Place the vehicle in P (PARK). 3. Turn off the ignition. 4. Then restart the engine.
If the ABS light remains on after resetting the system or comes on again while driving, the vehicle needs service. If the ABS light is on, but the regular brake system warning light is not on, the antilock brakes are not working properly, but the regular brakes are still functioning. Have the vehicle serviced right away. If both brake lights are on, the vehicle does not have antilock brakes, and there is a problem with the regular brakes as well. Have the vehicle towed for service. See Towing Your Vehicle on page 4-22.
StabiliTrak®/Traction Control System (TCS) Warning Light
The Traction Control System (TCS)/StabiliTrak® system warning light comes on briefly as the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator lights go off. This light flashes while the Traction Control System (TCS) and/or the StabiliTrak system are working. It also flashes when the Antilock Brake System (ABS) is activated. If the light comes on and stays on while driving there is a problem with the Traction Control System (TCS) or the StabiliTrak system. The
TCS and/or StabiliTrak system automatically turns off and vehicle needs service. When this light is on, the TCS system does not limit wheel spin and/or the StabiliTrak system does not assist with vehicle control. When the Traction Control system and/or StabiliTrak system are turned off, the light comes on. When the Traction Control System and/or StabiliTrak system are turned on, the light turns off. See Traction Control System (TCS) on page 4-8 and StabiliTrak® System on page 4-7 for more information.
Engine Coolant Temperature Warning Light The engine coolant temperature light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer.
Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 5-23. The vehicle’s engine could be damaged, and it might not be covered by the vehicle warranty. Never drive with the engine coolant temperature warning light on.
Instrument Panel
3-29
If this light comes on and stays on, the engine has overheated. Pull over and see Engine Overheating on page 5-23 for more information.
Tire Pressure Light
If the vehicle has a tire pressure monitoring system, the tire pressure light should come on briefly as the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. It provides information about tire pressures and the Tire Pressure Monitoring System.
When the Light is On Steady This indicates that one or more of the tires are significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See DIC
3-30
Instrument Panel
Warnings and Messages on page 3-42 for more information. Stop and check the tires as soon as it is safe to do so. If underinflated, inflate to the proper pressure. See Tires on page 5-38 for more information. When the Light Flashes First and Then is On Steady This indicates that there could be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle. See Tire Pressure Monitor System on page 5-45 for more information.
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer.
If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.
If the vehicle is
Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle’s emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 5-3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
The following can prevent more serious damage to the vehicle: (cid:129) Reduce vehicle speed. (cid:129) Avoid hard accelerations. (cid:129) Avoid steep uphill grades.
If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.
If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required.
Instrument Panel
3-31
An emission system malfunction might be corrected by: (cid:129) Make sure the fuel cap is fully installed. See Filling the Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. If the vehicle has been driven through a deep puddle of water, the vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off.
(cid:129) (cid:129) 3-32
Instrument Panel
(cid:129) Make sure to fuel the vehicle
with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and may cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Gasoline Octane on page 5-5.
If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection:
The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in ON/RUN and the light is not on.
The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if the battery has recently been replaced or if the battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection.
(cid:129) (cid:129) If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem.
Change Engine Oil Light
Change engine oil light means that service is required on the vehicle. See Scheduled Maintenance on page 6-3 and Engine Oil on page 5-11 for more information. After the engine oil is changed the engine oil life system needs to be reset in order to turn off this light. See Engine Oil Life System on page 5-14 for more information.
Instrument Panel
3-33
Security Light
For information regarding this light and the vehicle’s security system, see PASS-Key® III+ Electronic Immobilizer on page 2-12.
Cruise Control Light
The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 3-9 for more information.
Oil Pressure Light { CAUTION
Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty. Always follow the maintenance schedule in this manual for changing engine oil.
The oil pressure light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer/retailer.
3-34
Instrument Panel
Highbeam On Light
Fuel Gage
The highbeam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-7 for more information.
Low Washer Fluid Warning Light
The low washer fluid warning light comes on when the windshield washer fluid is low. See Windshield Washer Fluid on page 5-24 for more information.
United States Canada When the ignition is on, the fuel gage shows about how much fuel is in the fuel tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There still is a little fuel left, but the fuel tank should be refueled soon. See Low Fuel Warning Light on page 3-34 for more information. Four things that can happen but do not mean the fuel gage is not functioning properly are: (cid:129) At the service station, the fuel
pump shuts off before the gage reads full.
It takes a little more or less fuel to fill up than the fuel gage indicates. The gage moves a little while turning a corner or accelerating. The gage takes a few seconds to stabilize after the ignition is turned on, and goes back to empty after the ignition is turned off.
For the fuel tank capacity, see Capacities and Specifications on page 5-81.
Low Fuel Warning Light
The low fuel warning light, below the fuel gage, comes on briefly when the engine is started.
(cid:129) (cid:129) (cid:129) This light also comes on when the fuel tank is low on fuel. When fuel is added, the light should go off. If it does not, have the vehicle serviced.
Auto Stop Mode
Canada
United States This mark on the tachometer signifies that the engine is in Auto Stop mode which is a fuel saving operation. When the vehicle is off, the tachometer needle moves to OFF. If the driver’s door is opened while in Auto Stop, a chime sounds.
Charge/Assist Gage
The CHARGE/ASSIST gage displays the charge into and out of the hybrid battery. When the gage indicates ASSIST, the electric motor is performing an automatic restart of the engine, or the electric motor is assisting for maximum acceleration. When the gage indicates CHARGE, the electric motor operates as a generator to perform regenerative braking, while decelerating. See Regenerative Braking on page 2-23
for more information. The gage also indicates CHARGE when the system is recharging the hybrid battery.Instrument Panel
3-35
If the hybrid battery or other hybrid components are very hot or cold, the CHARGE and ASSIST functions can be suspended until the component temperatures are normal.
Fuel Economy Light
The ECO light comes on when the vehicle is achieving fuel economy close to its rated performance. Driving habits that improve fuel economy increases the time that the fuel economy light is on. To enable or disable the fuel economy light, while in park, press the Vehicle Info button on the DIC until PRESS V TO SET ECO is displayed. Then press the set/reset button to select off or on. For more information see Trip Odometer on page 3-24 and DIC Operation and Displays on page 3-36.
3-36
Instrument Panel
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All information appears in the DIC display located in the instrument panel cluster. The DIC comes on when the ignition is on. After a short delay, the DIC displays the information that was last displayed before the engine was turned off. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The DIC also displays the compass direction, outside air temperature, and shift position indicator at the top of the DIC display. If there is a problem with the system that controls the temperature display, the numbers will be replaced with dashes. If this occurs, have the vehicle serviced by your dealer/
retailer. If an abnormal temperature reading is displayed for an extended period of time, consult your dealer/retailer. Under certain circumstances, especially when the engine is idling, a delay updating the temperature display is normal. See DIC Compass on page 3-40
and Automatic Transmission Operation on page 2-20 for more information.DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, below the headlamp switch. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected.
The DIC also allows some features to be customized. See DIC Vehicle Customization on page 3-49 for more information.
DIC Buttons
The buttons are the trip/fuel, vehicle information, customization, and set/reset buttons. The button functions are detailed in the following pages.
3 (Trip/Fuel): Press this button to display the odometer, trip odometer, fuel range, average economy, and instantaneous economy. The compass and outside temperature will also be shown in the display. The temperature will be shown in °F or °C depending on the units selected.
T (Vehicle Information): Press this button to display the oil life, units, tire pressure readings for vehicles with the Tire Pressure Monitor System (TPMS), Remote Keyless Entry (RKE) transmitter programming, economy light on/off, compass zone setting, and compass recalibration on vehicles with this feature.
U (Customization): Press this button to customize the feature settings on your vehicle. See DIC Vehicle Customization on page 3-49
for more information.V (Set/Reset): Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC.
Trip/Fuel Menu Items 3 (Trip/Fuel): Press this button to scroll through the following menu items:
Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km). Pressing the trip odometer reset stem will also display the odometer. To switch between English and metric measurements, see “Units” later in this section.
Trip Odometer Press the trip/fuel button until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer. Pressing the trip odometer reset stem will also display the trip odometer.
Instrument Panel
3-37
The trip odometer can be reset to zero by pressing the set/reset button while the trip odometer is displayed. You can also reset the trip odometer while it is displayed by pressing and holding the trip odometer reset stem.
Fuel Range Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the vehicle’s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This estimate will change if driving conditions change. For example, if driving in traffic and making frequent stops, this display may read one number, but if the vehicle is driven on a freeway, the number may change even though the same
3-38
Instrument Panel
amount of fuel is in the fuel tank. This is because different driving conditions produce different fuel economies. Generally, freeway driving produces better fuel economy than city driving. Fuel range cannot be reset. If the vehicle is low on fuel, the FUEL LEVEL LOW message will be displayed. See “FUEL LEVEL LOW” under DIC Warnings and Messages on page 3-42.
Average Fuel Economy Press the trip/fuel button until AVERAGE FUEL ECONOMY displays. This display shows the approximate average miles per gallon (mpg) or liters per 100 kilometers (L/100 km). This number is calculated based on the number of mpg (L/100 km) recorded since the last time this menu item was reset. To reset the AVERAGE FUEL ECONOMY, press and hold the set/reset button. The display will show zero.
Instantaneous Fuel Economy If the vehicle has this display, press the trip/fuel button until INSTANT FUEL ECONOMY displays. This display shows the current fuel economy at a particular moment and will change frequently as driving conditions change. This display shows the instantaneous fuel economy in miles per gallon (mpg) or liters per 100 kilometers (L/100 km). Unlike average fuel economy, this display cannot be reset.
Blank Display This display shows no information.
Vehicle Information Menu Items
T (Vehicle Information): Press this button to scroll through the following menu items:
Oil Life Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change the oil on a schedule consistent with your driving conditions. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See “CHANGE ENGINE OIL SOON” under DIC Warnings and Messages on page 3-42. You should change the oil as soon as you can. See Engine Oil on page 5-11. In addition to the engine
FRONT TIRES PSI (kPa) LEFT ## RIGHT ##. Press the vehicle information button again until the DIC displays REAR TIRES PSI (kPa) LEFT ## RIGHT ##. If a low or high tire pressure condition is detected by the system while driving, a message advising you to check the pressure in a specific tire will appear in the display. See Inflation - Tire Pressure on page 5-43 and DIC Warnings and Messages on page 3-42
for more information. If the tire pressure display shows dashes instead of a value, there may be a problem with your vehicle. If this consistently occurs, see your dealer/retailer for service.Instrument Panel
3-39
Relearn Remote Key This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Press the vehicle information
button until PRESS V TO RELEARN REMOTE KEY displays.
2. Press the set/reset button until
REMOTE KEY LEARNING ACTIVE is displayed.
3. Press and hold the lock and
unlock buttons on the first transmitter at the same time for about 15 seconds. A chime will sound indicating that the transmitter is matched and REMOTE KEY LEARNING COMPLETE will be shown on the display.
oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Scheduled Maintenance on page 6-3
for more information.Units Press the vehicle information button until UNITS displays. This display allows you to select between English or Metric units of measurement. Once in this display, press the set/reset button to select between ENGLISH or METRIC units. All of the vehicle information will then be displayed in the unit of measurement selected.
Tire Pressure If your vehicle has the Tire Pressure Monitor System (TPMS), the pressure for each tire can be viewed in the DIC. The tire pressure will be shown in either pounds per square inch (psi) or kilopascals (kPa). Press the vehicle information button until the DIC displays
3-40
Instrument Panel
4. To match additional transmitters
at this time, repeat Step 3. Each vehicle can have a maximum of eight transmitters matched to it.
5. To exit the programming mode,
you must cycle the key to LOCK/OFF.
Compass Zone Setting This display allows for setting the compass zone. See DIC Compass on page 3-40 for more information.
Compass Recalibration This display allows for calibrating the compass. See DIC Compass on page 3-40 for more information.
ECO (Economy) Light On/Off This display allows you to turn the ECO light in the cluster on and off. See Fuel Economy Light on page 3-35 for more information. Press the vehicle information button until PRESS V SET ECO displays. This display will only
be available when the vehicle is in P (Park). Once in the display, press the set/reset button to select ON or OFF.
Blank Display This display shows no information.
DIC Compass Your vehicle may have a compass in the Driver Information Center (DIC).
Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/ retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly.
Compass variance is the difference between the earth’s magnetic north and true geographic north. If the compass is not set to the zone where you live, the compass may give false readings. The compass must be set to the variance zone in which the vehicle is traveling. To adjust for compass variance, use the following procedure:
Compass Variance (Zone) Procedure 1. Do not set the compass zone
when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS V TO SET COMPASS ZONE: ## displays.
5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure” following.
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible. If CAL should ever appear in the DIC display, the compass should be calibrated. If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic CB or cell phone
Instrument Panel
3-41
antenna mount, a magnetic emergency light, magnetic note pad holder, or any other magnetic item. Turn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass. To calibrate the compass, use the following procedure:
Compass Calibration Procedure 1. Before calibrating the compass,
make sure the compass is set to the variance zone in which the vehicle is located. See “Compass Variance (Zone) Procedure” earlier in this section. Do not operate any switches such as window, sunroof, climate controls, seats, etc. during the calibration procedure.
2. Press the vehicle information
button until PRESS V TO CALIBRATE COMPAS (Compass) displays.
2. Find the vehicle’s current
location and variance zone number on the map. Zones 1 through 15 are available.
3. Press and hold the set/reset button to scroll through and select the appropriate variance zone.
4. Press the trip/fuel button until the
vehicle heading, for example, N for North, is displayed in the DIC.
3-42
Instrument Panel
3. Press the set/reset button to start
the compass calibration.
4. The DIC will display
CALIBRATING COMPASS: TURN IN CIRCLES. Drive the vehicle in tight circles at less than 5 mph (8 km/h) to complete the calibration. The DIC will display COMPASS CALIBRATION COMPLETE for a few seconds when the calibration is complete. The DIC display will then return to the previous menu.
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press any of the DIC buttons, or the trip odometer reset stem on the
instrument panel cluster to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. Take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. The following are the possible messages that can be displayed and some information about them.
BATTERY SAVER ACTIVE This message displays when the charging system detects that the battery is being drained. You may notice that the vehicle attempts to reduce the drain for you by turning off accessories, such as interior fans, rear defogger, and heated seats. Turn off all
accessories. If the vehicle is not running, start and run the engine for at least 10 minutes to allow the battery to recharge. If the engine is running and the condition persists, see your dealer/retailer immediately. CALIBRATING COMPASS: TURN IN CIRCLES This message displays when calibrating the compass. Drive the vehicle in circles at less than 5 mph (8 km/h) to complete the calibration. See DIC Compass on page 3-40.
CHANGE ENGINE OIL SOON This message displays when service is required for the vehicle. See your dealer/retailer. See Engine Oil on page 5-11 and Scheduled Maintenance on page 6-3 for more information.
Acknowledging this message will not reset the OIL LIFE REMAINING display. That must be done at the OIL LIFE screen. See “OIL LIFE” under DIC Operation and Displays on page 3-36 and Engine Oil Life System on page 5-14 for more information. CHANGE TRANSMISSION FLUID Notice: Use of the incorrect automatic transmission fluid may damage the vehicle, and the damages may not be covered by the vehicle’s warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 6-11. This message displays when the life of the transmission fluid has expired and it should be changed. See Scheduled Maintenance on page 6-3 and Recommended Fluids and Lubricants on page 6-11
for the proper fluid and change intervals.CHECK TIRE PRESSURE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle’s tires needs to be checked. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate which tire needs to be checked. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the set/reset button. If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-38, Loading the Vehicle on page 4-18, and Inflation - Tire Pressure on page 5-43. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-36. If the tire pressure is
Instrument Panel
3-43
low, the low tire pressure warning light comes on. See Tire Pressure Light on page 3-29. COMPASS CALIBRATION COMPLETE This message displays when the compass calibration is complete. See DIC Compass on page 3-40. CRUISE CONTROL SET TO XXX This message displays whenever the cruise control is set. See Cruise Control on page 3-9 for more information.
DRIVER DOOR OPEN This message displays when the driver door is not closed properly. Close the door completely.
3-44
Instrument Panel
ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor is automatically turned off. When the coolant temperature returns to normal, the A/C operation automatically resumes. You can continue to drive your vehicle.
ENGINE OIL LOW: ADD OIL Your vehicle may have an engine oil level sensor. If it does, this message displays when the oil is low. See Engine Oil on page 5-11
for more information. ENGINE OVERHEATED IDLE ENGINE Notice: while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel clusterIf you drive your vehicle
and/or DIC, stop the vehicle as soon as possible. Do not increase the engine speed above normal idling speed. See Engine Overheating on page 5-23 for more information. This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED STOP ENGINE Notice: while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 5-23 for more information. This message displays along with a continuous chime when the engine has overheated. Stop and
If you drive your vehicle
turn the engine off immediately to avoid severe engine damage. See Engine Overheating on page 5-23.
ENGINE POWER IS REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer/ retailer for service as soon as possible.
Instrument Panel
3-45
PASSENGER DOOR OPEN This message displays when one or more of the passenger doors are not closed properly. Close the doors completely. REMOTE KEY LEARNING ACTIVE This message displays while matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “MATCHING TRANSMITTERS TO YOUR VEHICLE” under Remote Keyless Entry (RKE) System Operation on page 2-4 and DIC Operation and Displays on page 3-36 for more information.
FUEL LEVEL LOW This message displays when your vehicle is low on fuel. Refill the fuel tank as soon as possible. See Fuel Gage on page 3-34 and Filling the Tank on page 5-7 for more information.
HOOD OPEN This message displays on some vehicles when the hood is not closed properly. Close the hood completely. See Hood Release on page 5-9. ICE POSSIBLE DRIVE WITH CARE This message displays when the outside air temperature is cold enough to create icy road conditions. Adjust your driving accordingly.
LIFTGATE OPEN This message displays when the liftgate is not closed completely. Close the liftgate completely. See Liftgate on page 2-8.
If you drive your vehicle
OIL PRESSURE LOW STOP ENGINE Notice: while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected. See Engine Oil on page 5-11 for more information. This message displays when the vehicle’s engine oil pressure is low. The oil pressure light also appears on the instrument panel cluster. See Oil Pressure Light on page 3-33. Stop the vehicle immediately, as engine damage can result from driving a vehicle with low oil pressure. Have the vehicle serviced by your dealer/retailer as soon as possible when this message is displayed.
3-46
Instrument Panel
REMOTE KEY LEARNING COMPLETE This message displays while matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “MATCHING TRANSMITTERS TO YOUR VEHICLE” under Remote Keyless Entry (RKE) System Operation on page 2-4 and DIC Operation and Displays on page 3-36 for more information. REPLACE REMOTE KEY FOB BATTERY This message displays if a Remote Keyless Entry (RKE) transmitter battery is low. The battery needs to be replaced in the transmitter. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-4.
SERVICE A/C (Air Conditioning) SYSTEM This message displays when there is a problem detected in the air conditioning system. Have the vehicle serviced by your dealer/retailer.
SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately. See Airbag Readiness Light on page 3-25 for more information.
SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system or when the brake fluid level is low. See Brake System Warning Light on page 3-27. Have the brake system serviced by your dealer/retailer as soon as possible.
SERVICE HILL START ASSIST This message displays if there is a problem with the hill start assist function. Have your vehicle serviced by your dealer/retailer.
SERVICE HYBRID SYSTEM This message displays if the hybrid components need to be serviced. Have your vehicle serviced by your dealer/retailer.
SERVICE POWER STEERING This message displays if there has been a problem detected with the power steering. See Steering on page 4-9 for more information.
SERVICE STABILITRAK This message displays if there has been a problem detected with StabiliTrak®. A warning light also appears on the instrument panel cluster. See StabiliTrak®/ Traction Control System (TCS) Warning Light on page 3-28. See StabiliTrak® System on page 4-7 for more information. If this message turns on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off and then back on. If this message still stays on or turns back on again while you are driving, your vehicle needs service. Have the system inspected by your dealer/retailer as soon as possible.
SERVICE TIRE MONITORING SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 3-29. Several conditions may cause this message to appear. See Tire Pressure Monitor Operation on page 5-46 for more information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. SERVICE TRACTION CONTROL This message displays when the Traction Control System (TCS) is not functioning properly. A warning light also appears on the instrument panel cluster. See StabiliTrak®/Traction Control System (TCS) Warning Light on page 3-28
and Traction Control SystemInstrument Panel
3-47
(TCS) on page 4-8 for more information. Have the TCS serviced by your dealer/retailer as soon as possible.
SERVICE TRANSMISSION This message displays when there is a problem with the transmission. See your dealer/retailer for service.
SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer/retailer as soon as possible. SPEED LIMITED TO XXX MPH (KM/H) This message displays when your vehicle speed is limited to 80 mph (128 km/h) because the vehicle detects a problem in the speed variable assist steering system. Have your vehicle serviced by your dealer/retailer.
3-48
Instrument Panel
STABILITRAK NOT READY If your vehicle has StabiliTrak, this message may display and the StabiliTrak indicator light on the instrument panel cluster may be on after first driving the vehicle and exceeding 20 mph (32 km/h) for 30 seconds. The StabiliTrak system is not functional until the light has turned off. See StabiliTrak® System on page 4-7 for more information.
STABILITRAK OFF If your vehicle has StabiliTrak, this message displays when you turn off the StabiliTrak, or when the stability control has been automatically disabled. To limit wheel spin and realize the full benefits of the stability enhancement system, you should normally leave StabiliTrak on. However, you should turn StabiliTrak off if your vehicle gets stuck in sand, mud, ice, or snow and you want to rock your vehicle to attempt to free it, or if you are driving in extreme
off-road conditions and require more wheel spin. See If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-17. To turn the StabiliTrak system on or off, see StabiliTrak® System on page 4-7.
TIGHTEN GAS CAP This message may display along with the check engine light on the instrument panel cluster if the vehicle’s fuel cap is not tightened properly. See Malfunction Indicator Lamp on page 3-30. Reinstall the fuel cap fully. See Filling the Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn this light and message off.
TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection and Rotation on page 5-50, Tire Pressure Monitor System on page 5-45, and Inflation - Tire Pressure on page 5-43 for more information.
TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) turns off. See Traction Control System (TCS) on page 4-8 for more information. This message only displays while the ignition is in ON/RUN and disappears after 10 seconds, unless it is acknowledged or an urgent warning appears.
Do not drive your vehicle with overheated transmission fluid or while the transmission temperature warning is displayed. This message displays along with a chime if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears and the chime stops when the fluid temperature reaches a safe level.
TURN SIGNAL ON This message displays and a chime sounds as a reminder to turn off the turn signal if you drive your vehicle for more than about 3/4 mile (1.2 km) with a turn signal on. See Turn and Lane-Change Signals on page 3-6 for more information.
Instrument Panel
3-49
DIC Vehicle Customization Your vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers. All of the customization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization features were set when your vehicle left the factory, but may have been changed from their default state since then. The customization preferences are automatically recalled.
Any of the following conditions may cause the TCS to turn off:
The TCS is turned off by pressing the TCS/StabiliTrak button. See StabiliTrak® System on page 4-7 for more information. The battery is low. There is a TCS failure. See your dealer/retailer for service.
TRACTION CONTROL ON This message displays when the Traction Control System (TCS) turns on. See StabiliTrak® System on page 4-7 for more information. TRANSMISSION HOT IDLE ENGINE Notice: while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty.
If you drive your vehicle
(cid:129) (cid:129) (cid:129) 3-50
Instrument Panel
To change customization preferences, use the following procedure. Entering the Feature Settings Menu 1. Turn the ignition on and place
the vehicle in P (Park). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off.
2. Press the customization button to
scroll through the available customizable options.
Feature Settings Menu Items The following are customization features that allow you to program settings to the vehicle:
DISPLAY IN ENGLISH This feature will only display if a language other than English has been set. This feature allows you to change the language in which the DIC messages appear to English.
Press the customization button until the PRESS V TO DISPLAY IN ENGLISH screen appears on the DIC display. Press the set/reset button once to display all DIC messages in English.
DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the PRESS V TO SET DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: ENGLISH (default): All messages will appear in English. FRANCAIS: All messages will appear in French. ESPANOL: All messages will appear in Spanish.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Automatic Door Lock on page 2-7 for more information. Press the customization button until PRESS V TO SET AUTO DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: SHIFT OUT OF PARK (default): The doors will automatically lock when the vehicle is shifted out of P (Park).
AT VEHICLE SPEED: The doors will automatically lock when the vehicle speed is above 8 mph (13 km/h) for three seconds. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Automatic Door Unlock on page 2-7 for more information.
Press the customization button until PRESS V TO SET AUTO DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: None of the doors will automatically unlock. DRIVER DOOR AT KEY OUT: Only the driver’s door will unlock when the key is taken out of the ignition. DRIVER DOOR IN PARK: Only the driver’s door will unlock when the vehicle is shifted into P (Park). ALL DOORS AT KEY OUT: All of the doors will unlock when the key is taken out of the ignition.
Instrument Panel
3-51
ALL DOORS IN PARK (default): All of the doors will unlock when the vehicle is shifted into P (Park). NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-4 for more information.
3-52
Instrument Panel
Press the customization button until PRESS V TO SET REMOTE DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: VERIFICATION OFF: There will be no feedback when you press the lock button on the RKE transmitter. VERIFICATION LIGHTS ONLY: The exterior lamps will flash when you press the lock button on the RKE transmitter. VERIFICATION HORN ONLY: The horn will sound on the second press of the lock button on the RKE transmitter.
VERIFICATION HORN & LIGHTS (default): The exterior lamps will flash when you press the lock button on the RKE transmitter, and the horn will sound when the lock button is pressed again within five seconds of the previous command. VERIFICATION NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when unlocking the vehicle with the RKE transmitter if the doors are open. See Remote
Keyless Entry (RKE) System Operation on page 2-4 for more information. Press the customization button until PRESS V TO SET REMOTE DOOR UNLOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: VERIF LIGHTS OFF: The exterior lamps will not flash when you press the unlock button on the RKE transmitter. VERIF LIGHTS ON (default): The exterior lamps will flash when you press the unlock button on the RKE transmitter.
Press the customization button until PRESS V TO SET DELAY DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: There will be no delayed locking of the vehicle’s doors. ON (default): The doors will not lock until five seconds after the last door is closed. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
VERIF NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
DELAY DOOR LOCK On vehicles with a crew cab, this feature allows you to select whether or not the locking of the vehicle’s doors will be delayed. When locking the doors with the power door lock switch and a door is open, this feature will delay locking the doors until five seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. The key must be out of the ignition for this feature to work. You can temporarily override delayed locking by pressing the power door lock switch twice or the lock button on the RKE transmitter twice. See Delayed Locking on page 2-6
for more information.Instrument Panel
3-53
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until PRESS V TO SET EXIT LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The exterior lamps will not turn on. 10 SECONDS (default): The exterior lamps will stay on for 10 seconds. 30 SECONDS: The exterior lamps will stay on for 30 seconds. 2 MINUTES: The exterior lamps will stay on for two minutes.
3-54
Instrument Panel
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on briefly during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter. Press the customization button until PRESS V TO SET APPROACH LIGHTING appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: OFF: The exterior lights will not turn on when you unlock the vehicle with the RKE transmitter.
ON (default): If it is dark enough outside, the exterior lights will turn on briefly when you unlock the vehicle with the RKE transmitter.
The lights will remain on for 20 seconds or until the lock button on the RKE transmitter is pressed, or the vehicle is no longer off. See Remote Keyless Entry (RKE) System Operation on page 2-4
for more information. NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until PRESS V TO SET CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: NORMAL: The chime volume will be set to a normal level. LOUD: The chime volume will be set to a loud level. NO CHANGE: No change will be made to this feature. The current setting will remain. There is no default for chime volume. The volume will stay at the last known setting. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu. Press the customization button until PRESS V TO EXIT FEATURE SETTINGS appears in the DIC display. Press the set/reset button once to exit the menu. If you do not exit, pressing the customization button again will return you to the beginning of the feature settings menu.
Instrument Panel
3-55
Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs:
The vehicle is no longer in ON/RUN. The trip/fuel or vehicle information DIC buttons are pressed. The end of the feature settings menu is reached and exited. (cid:129) A 40 second time period has
elapsed with no selection made.
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until PRESS V TO RESTORE FACTORY SET appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The customization features will not be set to their factory default settings. To select a setting, press the set/reset button while the desired setting is displayed on the DIC.
(cid:129) (cid:129) (cid:129) 3-56
Instrument Panel
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features.
{ CAUTION
Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: (cid:129) Become familiar with the operation and controls of the audio system.
(cid:129) Set up the tone, speaker
adjustments, and preset radio stations.
For more information, see Defensive Driving on page 4-3. Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. Notice: The chime signals related to safety belts, parking brake, and other functions of your vehicle operate through the radio/entertainment system. If that equipment is replaced or additional equipment is added to your vehicle, the chimes may not work. Make sure that replacement or additional equipment is compatible with your vehicle before installing it. See Accessories and Modifications on page 5-3.
The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 2-15 for more information.
Setting the Clock Radio with Single CD (MP3) Player To set the time and date: 1. Turn the ignition key to
ACC/ACCESSORY or ON/RUN. Press O to turn the radio on.
2. Press H and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays.
3. Press the softkey located below
any one of the tabs that you want to change.
4. To increase the time or date do
one of the following: (cid:129) Press the softkey located
below the selected tab.
(cid:129) Press ¨SEEK, or \ FWD.
Turn f clockwise.
5. To decrease the time or date do
one of the following: (cid:129) Press ©SEEK or s REV.
Turn f counterclockwise. The date does not automatically display. To see the date press H while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.
To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1. Press H and then the softkey
located below the forward arrow label. Once the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays.
2. Press the softkey located below
the desired option.
3. Press H again to apply the
selected default, or let the screen time out.
Six-Disc CD (MP3) Player To set the time and date: 1. Turn the ignition key to
ACC/ACCESSORY or ON/RUN. Press O to turn the radio on.
2. Press MENU.
Instrument Panel
3-57
3. Press the softkey below the H
tab. The HR, MIN, MM, DD, YYYY displays.
4. Press the softkey below any one of the tabs you want to change. 5. To increase the time or date do
one of the following: (cid:129) Press the softkey located
below the selected tab.
(cid:129) Press ¨SEEK, or \ FWD.
Turn f clockwise.
6. To decrease the time or date do
one of the following: (cid:129) Press ©SEEK or s REV.
Turn f counterclockwise. The date does not automatically display. To see the date press MENU and then softkey below the H tab while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.
(cid:129) (cid:129) (cid:129) (cid:129) 3-58
Instrument Panel
To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1. Press MENU, and then the
softkey below the H tab. The HR, MIN, MM, DD, YYYY displays.
2. Press the softkey below the forward arrow tab. The time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays.
3. Press the softkey located below
the desired option.
4. Press MENU again to apply the
selected default, or let the screen time out.
Radio(s)
Radio with CD shown, Radio with Six-Disc CD similar
Radio Data System (RDS)
