2009 Saturn VUE Hybrid Owners Manual

Download PDF Manual
The audio system has a Radio Data System (RDS). The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters displays. In rare cases, a radio station can broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. The radio only seeks and scans stations with a strong signal that are in the selected band. Playing the Radio O (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. Finding a Station BAND: Press to switch between AM, FM, or XM™ (if equipped). f (Tune): Turn to select radio stations. ©SEEK ¨: Press to go to the previous or to the next station. To scan stations, press and hold either arrow for a few seconds until a beep sounds. The radio goes to a station, plays for a few seconds, then goes to the next station. Press either arrow again to stop scanning. 4 (Information) (XM™ Satellite Radio Service, MP3, and RDS Features): Press to display additional text information related to the current FM-RDS station, XM station, or MP3 song. If information is available, the song title information displays on the top line of the display and artist information displays on the bottom line. When information is not available, “NO INFO” displays. Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is parked. Tune to favorite stations using the presets, favorites button, and steering wheel controls, if the vehicle has them. See Defensive Driving on page 4-3. Instrument Panel 3-59 FAV (Favorites): A maximum of 36 stations can be programmed as favorites using the six pushbuttons positioned below the radio station frequency labels and by using the FAV button (radio favorites page). Press the FAV button to go through up to six pages of favorites, each having six favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or XM stations. To store a station as a favorite: 1. Tune to the desired radio station. 2. Press the FAV button to display the page where the station is to be stored. 3. Press and hold one of the six pushbuttons until a beep sounds. When that pushbutton is pressed and released, the station that was set, returns. 4. Repeat the steps for each pushbutton radio station to be stored as a favorite. 3-60 Instrument Panel The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 4. Press the FAV button, or let the menu time out, to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. Setting the Tone (Bass/Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust bass, midrange, or treble, press the f knob until the tone control tabs display. Continue pressing to highlight the desired tab, or press the pushbutton positioned under the desired tab. Turn the f knob to adjust the highlighted setting. Bass, midrange, or treble can also be adjusted by pressing either SEEK arrow, \ FWD, or s REV when the setting is highlighted until the desired level is obtained. If a station’s frequency is weak, or has static, decrease the treble. To quickly adjust bass, midrange, or treble to the middle position, press the pushbutton positioned under the BASS, MID, or TREB tab for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all tone and speaker controls to the middle position, press the f knob for more than two seconds until a beep sounds. EQ (Equalization): Press to select preset equalization settings. To return to the manual mode, press the EQ button until Manual displays or manually adjust the bass, midrange, or treble by pressing the f knob. Adjusting the Speakers (Balance/Fade) BAL/FADE (Balance/Fade): To adjust balance or fade, press the tune knob until the speaker control labels display. Continue pressing to highlight the desired tab, or press the pushbutton positioned under the desired label. Turn the f knob clockwise or counterclockwise to adjust the highlighted setting. The highlighted setting can also be adjusted by pressing either SEEK arrow, \ FWD, or s REV until the desired levels are obtained. To quickly adjust balance or fade to the middle position, press the pushbutton positioned under the BAL or FADE label for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all speaker and tone controls to the middle position, press the f knob for more than two seconds until a beep sounds. Finding a Category (CAT) Station CAT (Category): The CAT button is used to ﬁnd XM stations when the radio is in the XM mode. To ﬁnd XM channels within a desired category, perform the following: 1. Press the BAND button until the XM frequency displays. Press the CAT button to display the category tabs on the radio display. Continue pressing the CAT button until the desired category name displays. 2. Press either of the two buttons below the desired category tab to immediately tune to the ﬁrst XM station associated with that category. 3. Turn the f knob, press the buttons below the right or left arrows displayed, or press either SEEK arrow to go to the previous or to the next XM station within the selected category. Instrument Panel 3-61 4. To exit the category search mode, press the FAV button or BAND button to display favorites again. Undesired XM categories can be removed through the setup menu. To remove an undesired category: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the f knob to display the category to be removed. 4. Press the pushbutton located under the Remove tab until the category name along with the word Removed displays. 5. Repeat the steps to remove more categories. 3-62 Instrument Panel Removed categories can be restored by pressing the pushbutton under the Add tab when a removed category is displayed or by pressing the pushbutton under the Restore All tab. The radio does not allow categories to be removed or added while the vehicle is moving faster than 5 mph (8 km/h). XM™ Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle. A service fee is required to receive the XM service. For more information, contact XM at xmradio.com or call 1-800-929-2100 in the U.S. and xmradio.ca or call 1-877-438-9677 in Canada. Radio Messages for XM Only See XM Radio Messages on page 3-71 later in this section for further detail. Radio Messages Calibration Error: The audio system has been calibrated for the vehicle from the factory. If Calibration Error displays, it means that the radio has not been conﬁgured properly for the vehicle and it must be returned to your dealer/retailer for service. Locked: This message displays when the THEFTLOCK® system has locked up the radio. Take the vehicle to your dealer/retailer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. Playing a CD (Single CD Player) Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. Playing a CD(s) (Six-Disc CD Player) LOAD ^ : Press to load CDs into the CD player. This CD player holds up to six CDs. To insert one CD: 1. Press and release the ^ button. 2. Wait for the message to insert the disc. 3. Load a CD. Insert the CD partway into the slot, label side up. The player pulls the CD in. To insert multiple CDs: 1. Press and hold the ^ button for two seconds. A beep sounds and Load All Discs displays. 2. Follow the displayed instruction on when to insert the discs. The CD player takes up to six CDs. 3. Press the ^ button again to cancel loading more CDs. If the ignition or radio is turned off, with a CD in the player, it stays in the player. When the ignition or radio is turned on, the CD starts playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol displays on the CD. As each new track starts to play, the track number displays. The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring. Full-size CDs and the smaller CDs are loaded in the same manner. Care of CDs If playing a CD-R, the sound quality can be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. Handle them carefully. Store CD-R(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD does not play properly or not at all. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge. If the surface of a CD is soiled, take a soft, lint free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it. Make sure the wiping process starts from the center to the edge. Instrument Panel 3-63 Care of the CD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen. To prevent contaminating the lens of the disc optics with lubricants internal to the player mechanism the use of disc lens cleaners is not advised. Notice: or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error displays, see “CD Messages” later in this section. If a label is added to a CD, 3-64 Instrument Panel Z EJECT: To eject the CD that is currently playing, press and release this button. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The CD can be removed. If the CD is not removed, after several seconds, the CD automatically pulls back into the player and begins playing. For the Six-Disc CD player, press and hold Z for two seconds to eject all discs. f (Tune): Turn to select tracks on the CD currently playing. ©SEEK ¨: Press the left arrow to go to the start of the current track, if more than ten seconds have played. Press the right arrow to go to the next track. If either the left or right arrow is held, or pressed multiple times, the player continues moving backward or forward through the tracks on the CD. s REV (Fast Reverse): Press and hold to reverse playback quickly within a track. Sound is heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. \ FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound is heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. RDM (Random): With the random setting, the tracks can be listened to in random, rather than sequential order, on one CD or all CDs in a six-disc CD player. To use random: (cid:129) Press the pushbutton positioned under the RDM tab until Random Current Disc displays to play the tracks from a CD in random order. Press again to turn off random play. (cid:129) Press the pushbutton positioned under the RDM tab until Randomize All Discs displays to play tracks from all CDs loaded in a six-disc CD player in random order. Press again to turn off random play. BAND: Press to listen to the radio when a CD is playing. The CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press to play a CD when listening to the radio. The CD icon and track number displays when a CD is in the player. The radio system has an auxiliary input jack located on the lower right side of the faceplate. An external audio device such as a portable audio player can be connected to the auxiliary input jack for use as another source for playing CDs. Press the CD/AUX button again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, “No Input Device Found” displays. Playing an MP3 CD-R or CD-RW Disc The vehicle’s radio system may have the MP3 feature. If it has this feature, it is capable of playing an MP3 CD-R or CD-RW disc. For more information on how to play an MP3 CD-R or CD-RW disc, see Using an MP3 on page 3-66 later in this section. CD Messages CHECK DISC: If this message displays and/or the CD comes out, it could be: It is very hot. When the temperature returns to normal, the CD should play. The road is very rough. When the road becomes smoother, the CD should play. The CD is dirty, scratched, wet, or upside down. The air is very humid. If so, wait about an hour and try again. There could have been a problem while burning the CD. The label could be caught in the CD player. If the CD is not playing correctly, for any other reason, try a known good CD. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. If the radio displays an error message, write it down and provide it to your dealer/retailer when reporting the problem. Instrument Panel 3-65 Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. An external audio device such as an iPod™, laptop computer, MP3 player, CD changer, etc. can be connected to the auxiliary input jack for use as another audio source. Drivers are encouraged to set up any auxiliary device while the vehicle is in P (Park). See Defensive Driving on page 4-3 for more information on driver distraction. To use a portable audio player, connect a 3.5 mm (1/8 inch) cable to the radio’s front auxiliary input jack. When a device is connected, press the radio CD/AUX button to begin playing audio from the device over the vehicle speakers. (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) 3-66 Instrument Panel O (Power/Volume): Turn to increase or decrease the volume of the portable player. Additional volume adjustments might have to be made from the portable device if the volume is not loud or soft enough. BAND: Press to listen to the radio when a portable audio device is playing. The portable audio device continues playing. CD/AUX (CD/Auxiliary): Press to play a CD when a portable audio device is playing. Press again and the system begins playing audio from the connected portable audio player. If a portable audio player is not connected, “No Input Device Found” displays. Using an MP3 MP3 CD-R or CD-RW Disc The radio plays MP3 ﬁles that were recorded on a CD-R or CD-RW disc. The ﬁles can be recorded with the following ﬁxed bit rates: 32 kbps, 40 kbps, 56 kbps, 64 kbps, 80 kbps, 96 kbps, 112 kbps, 128 kbps, 160 kbps, 192 kbps, 224 kbps, 256 kbps, and 320 kbps or a variable bit rate. Song title, artist name, and album are available for display by the radio when recorded using ID3 tags version 1 and 2. Compressed Audio The radio also plays discs that contain both uncompressed CD audio (.CDA ﬁles) and MP3 ﬁles. By default the radio reads only the uncompressed audio and ignore the MP3 ﬁles. Pressing the CAT (category) button toggles between compressed and uncompressed audio format. MP3 Format To burn an MP3 disc on a personal computer: (cid:129) Make sure the MP3 ﬁles are recorded on a CD-R or CD-RW disc. (cid:129) Do not mix standard audio and MP3 ﬁles on one disc. The CD player is able to read and play a maximum of 50 folders, 50 playlists, and 255 ﬁles. (cid:129) Create a folder structure that makes it easy to ﬁnd songs while driving. Organize songs by albums using one folder for each album. Each folder or album should contain 18 songs or less. (cid:129) Avoid subfolders. The system can support up to eight subfolders deep, however, keep the total number of folders to a minimum in order to reduce the complexity and confusion in trying to locate a particular folder during playback. (cid:129) Instrument Panel 3-67 No Folder When the CD contains only compressed ﬁles, the ﬁles are located under the root folder. The next and previous folder functions do not display on a CD that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT. When the CD contains only playlists and compressed audio ﬁles, but no folders, all ﬁles are located under the root folder. The folder down and up buttons searches playlists (Px) ﬁrst and then go to the root folder. When the radio displays the name of the folder the radio displays ROOT. (cid:129) Make sure playlists have a .mp3 or .wpl extension, other ﬁle extensions may not work. (cid:129) Minimize the length of the ﬁle, folder or playlist names. Long ﬁle, folder, or playlist names, or a combination of a large number of ﬁles and folders, or playlists can cause the player to be unable to play up to the maximum number of ﬁles, folders, playlists, or sessions. To play a large number of ﬁles, folders, playlists or sessions, minimize the length of the ﬁle, folder, or playlist name. Long names also take up more space on the display, potentially getting cut off. Finalize the audio disc before burning it. Trying to add music to an existing disc can cause the disc not to function in the player. Playlists can be changed by using the previous and next folder buttons, the tune knob, or the SEEK arrows. An MP3 CD-R or CD-RW that was recorded using no ﬁle folders can also be played. If a CD-R or CD-RW contains more than the maximum of 50 folders, 50 playlists, and 255 ﬁles, the player can access and navigate up to the maximum, but all items over the maximum are not accessible. Root Directory The root directory of the CD-R or CD-RW is treated as a folder. If the root directory has compressed audio ﬁles, the directory displays as F1 ROOT. All ﬁles contained directly under the root directory are accessed prior to any root directory folders. However, playlists (Px) are always accessed before root folders or ﬁles. Empty Directory or Folder If a root directory or a folder exists somewhere in the ﬁle structure that contains only folders/subfolders and no compressed ﬁles directly beneath them, the player advances to the next folder in the ﬁle structure that contains compressed audio ﬁles. The empty folder does not display. (cid:129) 3-68 Instrument Panel Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: (cid:129) Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist. (cid:129) Play begins from the ﬁrst track in the ﬁrst folder and continues sequentially through all tracks in each folder. When the last track of the last folder has been played, play continues from the ﬁrst track of the ﬁrst folder. When play enters a new folder, the display does not automatically show the new folder name unless the folder mode is chosen as the default display. The new track name displays. File System and Naming The song name that is displayed is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the ﬁle name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened. Parts of words on the last page of text and the extension of the ﬁlename does not display. Preprogrammed Playlists Preprogrammed playlists that were created by WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed, however, they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song ﬁles. Playing an MP3 Insert a CD-R or CD-RW partway into the slot (Single CD Player), or press the ^ button and wait for the message to insert disc (Six-Disc CD Player), label side up. The player pulls it in, and the CD-R or CD-RW should begin playing. If the ignition or radio is turned off with a CD-R or CD-RW in the player, it stays in the player. When the ignition or radio is turned on, the CD-R or CD-RW starts to play where it stopped, if it was the last selected audio source. As each new track starts to play, the track number and song title displays. Z EJECT: Press and release to eject the CD-R or CD-RW that is playing. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The CD-R or CD-RW can be removed. If the CD-R or CD-RW is not removed, after several seconds, the CD-R or CD-RW automatically pulls back into the player and begins playing. For the Six-Disc CD player, press and hold this button for two seconds to eject all discs. f (Tune): Turn to select MP3 ﬁles on the CD-R or CD-RW currently playing. ©SEEK ¨: Press the left arrow to go to the start of the current MP3 ﬁle, if more than ten seconds have played. Press the right arrow to go to the next MP3 ﬁle. If either arrow is held or pressed multiple times, the player continues moving backward or forward through MP3 ﬁles on the CD. S c (Previous Folder): Press the pushbutton positioned under the Folder label to go to the ﬁrst track in the previous folder. c T (Next Folder): Press the pushbutton positioned under the Folder label to go to the ﬁrst track in the next folder. s REV (Reverse): Press and hold to reverse playback quickly within an MP3 ﬁle. Sound is heard at a reduced volume. Release to resume playing the ﬁle. The elapsed time of the ﬁle displays. \ FWD (Fast Forward): Press and hold to advance playback quickly within an MP3 ﬁle. Sound is heard at a reduced volume. Release to resume playing the ﬁle. The elapsed time of the ﬁle displays. Instrument Panel 3-69 RDM (Random): With the random setting, the MP3 ﬁles on the CD-R or CD-RW can be listened to in random, rather than sequential order, on one CD-R/CD-RW or all discs in a six-disc CD player. To use random, do one of the following: 1. To play MP3 ﬁles from the CD-R or CD-RW in random order, press the pushbutton positioned under the RDM label until Random Current Disc displays. Press the same pushbutton again to turn off random play. 2. To play songs from all CDs loaded in a six-disc CD player in random order, press the pushbutton positioned under the RDM label until Randomize All Discs displays. Press the same pushbutton again to turn off random play. 3-70 Instrument Panel h (Music Navigator): Use the music navigator feature to play MP3 ﬁles on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator label. The player scans the disc to sort the ﬁles by artist and album ID3 tag information. It can take several minutes to scan the disc depending on the number of MP3 ﬁles recorded to the CD-R or CD-RW. The radio can begin playing while it is scanning the disc in the background. When the scan is ﬁnished, the CD-R or CD-RW begins playing again. Once the disc has been scanned, the player defaults to playing MP3 ﬁles in order by artist. The current artist playing is shown on the second line of the display between the arrows. Once all songs by that artist are played, the player moves to the next artist in alphabetical order on the CD-R/CD-RW and begins playing MP3 ﬁles by that artist. To listen to MP3 ﬁles by another artist, press the pushbutton located below either arrow button. The disc goes to the next or previous artist in alphabetical order. Continue pressing either button until the desired artist is displayed. To change from playback by artist to playback by album, press the pushbutton located below the Sort By label. From the sort screen, push one of the buttons below the album button. Press the pushbutton below the back label to return to the main music navigator screen. Now the album name is displayed on the second line between the arrows and songs from the current album begins to play. Once all songs from that album are played, the player moves to the next album in alphabetical order on the CD-R/CD-RW and begins playing MP3 ﬁles from that album. To exit music navigator mode, press the pushbutton below the Back label to return to normal MP3 playback. BAND: Press to listen to the radio while a CD is playing. The inactive CD remains inside the radio for future listening. CD/AUX (CD/Auxiliary): Press to play a CD while listening to the radio. The CD icon and a message showing disc and/or track number displays while a CD is in the player. Press this button again and the system automatically searches for an auxiliary input device such as a portable audio player. If a portable audio player is not connected, “No Aux Input Device” displays. XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. Channel Off Air: This channel is not currently in service. Tune in to another channel. Channel Unauth: This channel is blocked or cannot be received with your XM Subscription package. Channel Unavail: This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No Artist Info: No artist information is available at this time on this channel. The system is working properly. No Title Info: No song title information is available at this time on this channel. The system is working properly. No CAT Info: No category information is available at this time on this channel. The system is working properly. No Information: No text or informational messages are available at this time on this channel. The system is working properly. Instrument Panel 3-71 CAT Not Found: There are no channels available for the selected category. The system is working properly. XM Theftlocked: The XM™ receiver in your vehicle could have previously been in another vehicle. For security purposes, XM™ receivers cannot be swapped between vehicles. If this message is received after having your vehicle serviced, check with your dealer/retailer. XM Radio ID: If tuned to channel 0, this message alternates with the XM™ Radio 8 digit radio ID label. This label is needed to activate the service. Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. 3-72 Instrument Panel Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. Bluetooth® Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Proﬁle to make and receive phone calls. The system can be used while the key is in ON/RUN or ACC/ACCESSORY position. The range of the Bluetooth system can be up to 30 ft. (9.1 m). Not all phones support all functions, and not all phones are guaranteed to work with the in-vehicle Bluetooth system. See gm.com/bluetooth for more information on compatible phones. Voice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise. When to Speak: A short tone sounds after the system responds indicating when it is waiting for a voice command. Wait until the tone and then speak. How to Speak: Speak clearly in a calm and natural voice. Audio System When using the in-vehicle Bluetooth system, sound comes through the vehicle’s front audio system speakers and overrides the audio system. Use the audio system volume knob, during a call, to change the volume level. The adjusted volume level remains in memory for later calls. To prevent missed calls, a minimum volume level is used if the volume is turned down too low. Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-82 for more information. J / 0 (Push To Talk): Press to answer incoming calls, conﬁrm system information, and to start speech recognition. − / K (Phone On Hook): Press to end a call and to cancel an operation. Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system ﬁrst and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar® Hands-Free Calling, if available. Refer to the OnStar owner’s guide for more information. Pairing Information: (cid:129) Up to ﬁve cell phones can be paired to the in-vehicle Bluetooth system. The pairing process is disabled when the vehicle is moving. The in-vehicle Bluetooth system automatically links with the ﬁrst available paired cell phone in the order the phone was paired. (cid:129) Only one paired cell phone can be connected to the in-vehicle Bluetooth system at a time. (cid:129) Pairing should only need to be completed once, unless changes to the pairing information have been made or the phone is deleted. To link to a different paired phone, see Linking to a Different Phone later in this section. Pairing a Phone 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Pair”. The system responds with instructions and a four digit PIN number. The PIN number will be used in Step 4. 4. Start the Pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturers user guide for information on this process. Instrument Panel 3-73 Locate the device named “General Motors” in the list on the cellular phone and follow the instructions on the cell phone to enter the four digit PIN number that was provided in Step 3. 5. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then conﬁrms the name provided. 6. The system responds with “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. (cid:129) (cid:129) 3-74 Instrument Panel Listing All Paired and Connected Phones 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices. If a phone is connected to the vehicle, the system will say “Is connected” after the connected phone. Deleting a Paired Phone 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Delete”. The system asks which phone to delete followed by a tone. 4. Say the name of the phone to be deleted. If the phone name is unknown, use the “List” command for a list of all paired phones. The system responds with “Would you like to delete ? Yes or No” followed by a tone. 5. Say “Yes” to delete the phone. The system responds with “OK, deleting ”. Linking to a Different Phone 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Change phone”. The system responds with “Please wait while I search for other phones”. If another phone is found, the response will be “ is now connected”. If another phone is not found, the original phone remains connected. Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: (cid:129) Store (cid:129) Digit Store (cid:129) Directory (cid:129) (cid:129) Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please” followed by a tone. 3. Say the complete phone number to be stored at once with no pauses. If the system recognizes the number it responds with “OK, Storing” and repeats the phone number. If the system is unsure it recognizes the phone number, it responds with “Store” and repeats the number followed by “Please say yes or no”. If the number is correct, say “Yes”. If the number is not correct, say “No”. The system will ask for the number to be re-entered. 4. After the system stores the phone number, it responds with “Please say the name tag” followed by a tone. 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store . Does that sound OK?”. If the name tag does not sound correct, say “No” and repeat Step 5. Instrument Panel 3-75 If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu. Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Store”. The system responds with “Please say the ﬁrst digit to store” followed by a tone. (cid:129) (cid:129) (cid:129) (cid:129) 3-76 Instrument Panel 3. Say the ﬁrst digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store . Does that sound OK?”. If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time and the system will repeat them. 4. After the complete number has been entered, say “Store”. The system responds with “Please say the name tag” followed by a tone. If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu. Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Directory”. The system responds with “Directory” and then plays back all of the stored name tags. When the list is complete, the system returns to the main menu. Deleting Name Tags The system uses the following commands to delete name tags: (cid:129) Delete (cid:129) Delete all name tags Using the Delete Command The delete command allows speciﬁc name tags to be deleted. To use the delete command: 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete”. The system responds with “Delete, please say the name tag” followed by a tone. (cid:129) (cid:129) (cid:129) (cid:129) 3. Say the name tag to be deleted. The system responds with “Would you like to delete, ? Please say yes or no”. If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting , returning to the main menu.” If the name tag is incorrect, say “No”. The system responds with “No. OK, let’s try again, please say the name tag.” Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). To use the delete all name tags command: 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Delete all name tags”. The system responds with “You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no.” (cid:129) Say “Yes” to delete all name tags. (cid:129) Say “No” to cancel the function and return to the main menu. Making a Call Calls can be made using the following commands: (cid:129) Dial (cid:129) Digit Dial (cid:129) Call (cid:129) Re-dial Instrument Panel 3-77 Using the Dial Command 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Dial using . “Number please” followed by a tone. 3. Say the entire number without pausing. If the system recognizes the number, it responds with “OK, Dialing” and dials the number. If the system does not recognize the number, it conﬁrms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number to be re-entered. (cid:129) (cid:129) (cid:129) (cid:129) 3-78 Instrument Panel Using the Digit Dial Command 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Dial”. The system responds with “Digit dial using , please say the ﬁrst digit to dial” followed by a tone. 3. Say the digit to be dialed one at a time. Following each digit, the system will repeat back the digit it heard followed by a tone. 4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time and the system will repeat them. Using the Call Command 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using . Please say the name tag” followed by a tone. 3. Say the name tag of the person to call. If the system clearly recognizes the name tag it responds with “OK, calling, ” and dials the number. If the system is unsure it recognizes the right name tag, it conﬁrms the name tag followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, calling, ” and dials the number. If the name tag is not correct, say “No”. The system will ask for the name tag to be re-entered. Once connected, the person called will be heard through the audio speakers. Using the Re-dial Command 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. After the tone, say “Re-dial”. The system responds with “Re-dial using ” and dials the last number called from the connected Bluetooth phone. (cid:129) (cid:129) (cid:129) (cid:129) Once connected, the person called will be heard through the audio speakers. Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. (cid:129) Press J / 0 and begin speaking to answer the call. (cid:129) Press − / K to ignore a call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. (cid:129) Press J / 0 to answer an incoming call when another call is active. The original call is placed on hold. (cid:129) Press J / 0 again to return to the original call. To ignore the incoming call, continue with the original call with no action. (cid:129) Press − / K to disconnect the current call and switch to the call on hold. Three-Way Calling Three-Way Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press J / 0. The system responds with “Ready” followed by a tone. 2. Say “Three-way call”. The system responds with “Three-way call, please say dial or call”. 3. Use the dial or call command to dial the number of the third party to be called. 4. Once the call is connected, press J / 0 to link all the callers together. Instrument Panel 3-79 Ending a Call Press − / K to end a call. Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press J / 0. The system responds with “Ready” followed by a tone. 2. Say “Mute Call”. The system responds with “Call muted”. To Cancel Mute 1. Press J / 0. The system responds with “Ready” followed by a tone. 2. After the tone, say “Mute Call”. The system responds with “Resuming call”. (cid:129) 3-80 Instrument Panel Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press J / 0. The system responds with “Ready” followed by a tone. 2. Say “Transfer Call.” The system responds with “Transferring call” and the audio will switch from the vehicle to the cell phone. To Transfer Audio to the In-Vehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the key is turned to the ON/RUN or ACC/ACCESSORY position. During a call with the audio on the cell phone, press J / 0 for more than two seconds. The audio switches from the cell phone to the vehicle. Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1. Press and hold J / 0 for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Voice”. The system responds with “OK, accessing ”. The cell phone’s normal prompt messages will go through its cycle according to the phone’s operating instructions. Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls. Sending a Number During a Call 1. Press J / 0. The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Say a number to send tones” followed by a tone. (cid:129) 3. Say the number to send. 3. Say the name tag to send. If the system clearly recognizes the number it responds with “OK, Sending Number” and the dial tones are sent and the call continues. If the system is not sure it recognized the number properly, it responds “Dial Number, Please say yes or no?” followed by a tone. If the number is correct, say “Yes”. The system responds with “OK, Sending Number” and the dial tones are sent and the call continues. Sending a Stored Name Tag During a Call 1. Press J / 0. The system responds with “Ready” followed by a tone. 2. Say “Send name tag.” The system responds with “Say a name tag to send tones” followed by a tone. If the system clearly recognizes the name tag it responds with “OK, Sending ” and the dial tones are sent and the call continues. If the system is not sure it recognized the name tag properly, it responds “Dial , Please say yes or no?” followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, Sending ” and the dial tones are sent and the call continues. Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indeﬁnitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see Instrument Panel 3-81 the above sections on Deleting a Paired Phone and Deleting Name Tags. Other Information The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. (cid:129) (cid:129) (cid:129) (cid:129) 3-82 Instrument Panel This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Theft-Deterrent Feature THEFTLOCK® is designed to discourage theft of the vehicle’s radio by learning a portion of the Vehicle Identiﬁcation Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle. Audio Steering Wheel Controls Some audio controls can be adjusted at the steering wheel. They include the following: + / − (Next/Previous): Press and release to go to the next or the previous preset radio station or CD track. K (End Call): For vehicles with the OnStar® system, press to end a Hands-Free call, an OnStar® call, cancel an incoming call, or end the Advisor Playback. For vehicles with Bluetooth®, press to end a call, or cancel an incoming call. v + v −(Volume): Move the thumbwheel up or down to increase or to decrease the volume. J 0 (Call / Mute): Press and release to mute the system. Press it again to turn the sound back on. For vehicles with OnStar® or Bluetooth systems, press and hold for longer than two seconds to interact with those systems. See OnStar® System on page 2-29 and Bluetooth® on page 3-72 in this manual for more information. Instrument Panel 3-83 Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off. Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio. FM Stereo FM signals only reach about 10 to 40 miles (16 to 65 km). Although the radio has a built-in electronic circuit that automatically works to reduce interference, some static can occur, especially around tall buildings or hills, causing the sound to fade in and out. XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the XM signal for a period of time. Chime Level Adjustment The radio may be used to adjust the vehicle’s chime level. If the radio can be used to change the volume level of the chime, press and hold the sixth FAV softkey with the ignition on and the radio power off. The volume level changes between Normal and Loud. The selected volume level appears on the radio display. Removing the radio and not replacing it with a factory radio or chime module will disable vehicle chimes. 3-84 Instrument Panel Fixed Mast Antenna The ﬁxed mast antenna can withstand most car washes without being damaged as long as it is securely attached to the base. If the mast becomes slightly bent, straighten it out by hand. If the mast is badly bent, replace it. Occasionally check to make sure the antenna is tightened to its base. If tightening is required, tighten by hand. XM™ Satellite Radio Antenna System The XM Satellite Radio antenna is located on the roof of the vehicle. Keep the antenna clear of obstructions for clear radio reception. If the vehicle has a sunroof, the performance of the XM system may be affected if the sunroof is open. Off-Road Recovery ............4-10 Passing .............................4-11 Loss of Control .................4-11 Driving at Night .................4-12 Driving in Rain and on Wet Roads ......................4-13 Before Leaving on a Long Trip ........................4-14 Highway Hypnosis .............4-14 Hill and Mountain Roads .............................4-14 Winter Driving ...................4-15 If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow ...........................4-17 Rocking Your Vehicle to Get It Out .......................4-17 Loading the Vehicle ..........4-18 Towing Towing Your Vehicle .........4-22 Recreational Vehicle Towing ............................4-23 Towing a Trailer ................4-26 Driving Your Vehicle 4-1 Your Driving, the Road, and the Vehicle Driving Your Vehicle Whenever we drive, we are taking on an important responsibility. This is true for any motor vehicle — passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle’s design all affect how well a vehicle performs. But statistics show that the most important factor, by far, is how we drive. Knowing how these three factors work together can help you understand how your vehicle handles and what you can do to avoid many types of crashes, including a rollover crash. Driving Your Vehicle Your Driving, the Road, and the Vehicle Driving Your Vehicle ...........4-1 Driver Behavior ...................4-2 Driving Environment ............4-2 Vehicle Design ...................4-2 Driving for Better Fuel Economy ...........................4-3 Defensive Driving ................4-3 Drunk Driving .....................4-4 Control of a Vehicle ............4-4 Braking ...............................4-5 Antilock Brake System (ABS) ...................4-6 Braking in Emergencies ......4-6 StabiliTrak® System ............4-7 Traction Control System (TCS) ...................4-8 Steering ..............................4-9 4-2 Driving Your Vehicle Driver Behavior The single most important thing is this: everyone in the vehicle, including the driver, should buckle up. See Safety Belts: They Are for Everyone on page 1-10. In fact, most serious injuries and fatalities to unbelted occupants can be reduced or prevented by the use of safety belts. In a rollover crash, an unbelted person is signiﬁcantly more likely to die than a person wearing a seat belt. In addition, avoiding excessive speed, sudden or abrupt turns, and drunken or aggressive driving can help make trips safer and avoid the possibility of a crash, especially a rollover crash. This section provides many useful tips to help you drive more safely. Driving Environment You can also help avoid a rollover or other type of crash by being prepared for driving in inclement weather, at night, or during other times where visibility or traction may be limited, such as on curves, slippery roads, or hilly terrain. Unfamiliar surroundings can also have hidden hazards. To help you learn more about driving in different conditions, this section contains information about city, freeway, and off-road driving, as well as other hints for driving in various weather conditions. Vehicle Design According to the U.S. Department of Transportation, utility vehicles have a signiﬁcantly higher rollover rate than other types of vehicles. Utility vehicles do have higher ground clearance and a narrower track or shorter wheelbase than passenger cars, to make them more capable for off-road driving. Speciﬁc design characteristics like these give the driver a better view of the road, but also give utility vehicles a higher center of gravity than other types of vehicles. This means that you should not expect a utility vehicle to handle the same way a vehicle with a lower center of gravity, like a car, would in similar situations. But driver behavior factors are far more often the cause of a utility vehicle rollover than are environmental or vehicle factors. Safe driver behavior and understanding the environment in which you will be driving can help avoid a rollover crash in any type of vehicle, including utility vehicles. Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. (cid:129) Avoid fast starts and accelerate smoothly. (cid:129) Brake gradually and avoid abrupt stops. (cid:129) Avoid idling the engine for long periods of time. (cid:129) When road and weather conditions are appropriate, use cruise control, if equipped. (cid:129) Always follow posted speed limits or drive more slowly when conditions require. (cid:129) Keep vehicle tires properly inﬂated. (cid:129) Combine several trips into a single trip. (cid:129) Replace the vehicle’s tires with the same TPC Spec number molded into the tire’s sidewall near the size. Follow recommended scheduled maintenance. Defensive Driving Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-10. Driving Your Vehicle 4-3 { CAUTION Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready. In addition: (cid:129) Allow enough following distance between you and the driver in front of you. (cid:129) Focus on the task of driving. Driver distraction can cause collisions resulting in injury or possible death. These simple defensive driving techniques could save your life. (cid:129) 4-4 Driving Your Vehicle Drunk Driving { CAUTION Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking. Ride home in a cab; or if you are with a group, designate a driver who will not drink. Death and injury associated with drinking and driving is a global tragedy. Alcohol affects four things that anyone needs to drive a vehicle: judgment, muscular coordination, vision, and attentiveness. Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person’s chance of being killed or permanently disabled is higher than if the person had not been drinking. Control of a Vehicle The following three systems help to control the vehicle while driving —brakes, steering, and accelerator. At times, as when driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide. Meaning, you can lose control of the vehicle. See Traction Control System (TCS) on page 4-8. Adding non-dealer/non-retailer accessories can affect vehicle performance. See Accessories and Modiﬁcations on page 5-3. Driving Your Vehicle 4-5 If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied. Once the power assist is used up, it can take longer to stop and the brake pedal will be harder to push. Adding non-dealer/non-retailer accessories can affect vehicle performance. See Accessories and Modiﬁcations on page 5-3. Braking See Brake System Warning Light on page 3-27. Braking action involves perception time and reaction time. Deciding to push the brake pedal is

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Saturn VUE Hybrid Owners Manual