2010 Nissan Xterra Owners Manual

inform the buyer about the front air bag system and guide the buyer to the appropriate sections in this Owner’s Manual.

Safety—Seats, seat belts and supplemental restraint system 1-55

collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is im- pacted. They may not inflate in certain side colli- sions.

Curtain and rollover air bags are also designed to inflate in certain types of rollover collisions or near rollovers. As a result, certain vehicle movements (for example, during severe off roading) may cause the curtain and rollover air bags to inflate. Vehicle damage (or lack of it) is not always an indication of proper side air bag and curtain and rollover air bag operation. When the side air bags and curtain and rollover supplemental air bags inflate, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. Side air bags, along with the use of seat belts, help to cushion the impact force on the chest of the front occupants. Curtain and rollover air bags help to cushion the impact force to the head of occupants in the front and rear outboard seating positions. They can help save lives and reduce serious injuries. However, an inflating side air bag

LRS0592

Front seat-mounted side-impact supplemental air bag and roof- mounted curtain side-impact and rollover supplemental air bag systems The side air bags are located in the outside of the seatback of the front seats. The curtain and roll- over air bags are located in the side roof rails. These systems are designed to meet voluntary guidelines to help reduce the risk of injury to out-of-position occupants. However, all of the information, cautions and warnings in this manual still apply and must be followed. The side air bags and curtain and rollover air bags are designed to inflate in higher severity side 1-56 Safety—Seats, seat belts and supplemental restraint system

or curtain and rollover air bag may cause abra- sions or other injuries. Side air bags and curtain and rollover air bags do not provide restraint to the lower body.

The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the side air bag. Rear seat passengers should be seated as far away as practical from the door finishers and side roof rails. The side air bags and curtain and rollover air bags inflate quickly in order to help protect the occupants. Because of this, the force of the side air bag and curtain and rollover air bag inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation. The side air bag will deflate quickly after the collision is over.

The curtain and rollover air bags will remain in- flated for a short time. The side air bags and curtain and rollover air bags operate only when the ignition switch is in the ON or START position.

After placing the ignition switch in the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

WARNING

● Do not place any objects near the seat- back of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates.

● Right after inflation, several side air bag and curtain and rollover air bag system components will be hot. Do not touch them; you may severely burn yourself.

● No unauthorized changes should be made to any components or wiring of the side air bag and curtain and rollover air bag systems. This is to prevent dam- age to or accidental inflation of the side air bag and curtain and rollover air bag systems.

● Do not make unauthorized changes to your vehicle’s electrical system, sus- pension system or side panel. This could affect proper operation of the curtain and rollover air bag systems.

● Tampering with the side air bag system may result in serious personal injury. For example, do not change the front seats by placing material near the seat- backs or by installing additional trim material, such as seat covers, around the side air bag.

● Work around and on the side air bag and curtain and rollover air bag systems should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The SRS wiring harnesses* should not be modified or discon- nected. Unauthorized electrical test equipment and probing devices should not be used on the side air bag or cur- tain and rollover air bag systems.

* The SRS wiring harness or connectors are yellow or orange for easy identification.

When selling your vehicle, we request that you inform the buyer about the side air bag and curtain and rollover air bag systems and guide the buyer to the appropriate sections in this Owner’s Manual.

Seat belts with pretensioners (Front seats)

WARNING

● The pretensioners cannot be reused af- ter activation. They must be replaced together with the retractor and buckle as a unit.

● If the vehicle becomes involved in a frontal collision but a pretensioner is not activated, be sure to have the pre- tensioner system checked and, if nec- essary, your NISSAN dealer.

replaced by

● No unauthorized changes should be made to any components or wiring of the pretensioner system. This is to pre- vent damage to or accidental activation of the pretensioners. Tampering with the pretensioner system may result in serious personal injury.

● Work around and on the pretensioner system should be done by a NISSAN dealer. Installation of electrical equip- ment should also be done by a NISSAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pretensioner system.

Safety—Seats, seat belts and supplemental restraint system 1-57

the

supplemental

If any abnormality occurs in the pretensioner sys- tem, air bag warning light will not come on, will flash intermit- tently or will turn on for 7 seconds and remain on after the ignition switch has been placed in the ON or START position. In this case, the preten- sioner system may not function properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer. When selling your vehicle, we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections in this Owner’s Manual.

● If you need to dispose of a pretensioner or scrap the vehicle, contact a NISSAN dealer. Incorrect disposal procedures could cause personal injury.

The pretensioner system activates in conjunction with the front air bag system. The pretensioner system also activates with the curtain and rollover air bags in certain types of rollover collisions or near rollovers. Working with the seat belt retrac- tor, it helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants. The pretensioner is encased with the seat belt retractor. These seat belts are used the same way as conventional seat belts. When a pretensioner activates, smoke is re- leased and a loud noise may be heard. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. After pretensioner activation, load limiters allow the seat belt to release webbing (if necessary) to reduce forces against the chest.

1-58 Safety—Seats, seat belts and supplemental restraint system

WRS0885

1. SRS Air Bag Warning Labels

The warning labels are located on the sur- face of the sun visor.

SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front- impact air bag system are placed in the vehicle as shown in the illustration.

When the ignition switch is placed in the ON or START position, the supplemental air bag warn- ing light illuminates for about 7 seconds and then turns off. This means the system is operational.

If any of the following conditions occur, the front air bag, side air bag, curtain and rollover air bag and pretensioner systems need servicing: ● The supplemental air bag warning light re-

mains on after approximately 7 seconds.

● The supplemental air bag warning light

flashes intermittently.

● The supplemental air bag warning light does

not come on at all.

Under these conditions, the front air bag, side air bag, curtain and rollover air bag or pretensioner systems may not operate properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer.

WARNING

If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain and rollover air bag and/or pretensioner systems will not op- erate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.

Repair and replacement procedure The front air bags, side air bags, curtain and rollover air bags and pretensioners are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred. Repair and replacement of these supplemental air bag systems should be done only by a NISSAN dealer.

When maintenance work is required on the ve- hicle, the front air bags, side air bags, curtain and rollover air bags, pretensioners and related parts should be pointed out to the person performing the maintenance. The ignition switch should al- ways be in the LOCK position when working under the hood or inside the vehicle.

Safety—Seats, seat belts and supplemental restraint system 1-59

LRS0100

SUPPLEMENTAL AIR BAG WARNING LIGHT air bag warning light, The supplemental displaying in the instrument panel, moni- tors the circuits of the supplemental front-impact air bag, front seat-mounted side-impact supple- mental air bag, roof-mounted curtain side-impact and rollover supplemental air bag and seat belt pretensioner systems. The monitored circuits in- clude the Air bag Control Unit (ACU), crash zone sensor, satellite sensors, rollover sensor, occu- pant classification sensor, front air bag modules, side air bag modules, curtain and rollover air bag modules, pretensioners and all related wiring.

WARNING

● Once a front air bag, side air bag, or curtain and rollover air bag has inflated, the air bag module will not function again and must be replaced. Addition- ally, if any of the front air bags inflate, the activated pretensioners must also be replaced. The air bag module and pretensioner should be replaced by a NISSAN dealer. The air bag module and pretensioner cannot be repaired.

● The front air bag, side air bag, curtain and rollover air bag systems and the pretensioner system should be in- spected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle.

● If you need to dispose of a supplemen- tal air bag or pretensioner or scrap the vehicle, contact a NISSAN dealer. Incor- rect disposal procedures could cause personal injury.

1-60 Safety—Seats, seat belts and supplemental restraint system

MEMO

Safety—Seats, seat belts and supplemental restraint system 1-61

2 Instruments and controls

Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4
Trip computer (if so equipped) . . . . . . . . . . . . . . . . . . . 2-5
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-6
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Engine oil pressure gauge . . . . . . . . . . . . . . . . . . . . . . . 2-8
Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Compass display (if so equipped) . . . . . . . . . . . . . . . . . . . 2-9
Compass display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Warning/indicator lights and audible reminders . . . . . . 2-12
Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Security systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Vehicle security system. . . . . . . . . . . . . . . . . . . . . . . . . 2-22
NISSAN vehicle immobilizer system . . . . . . . . . . . . . 2-23
Windshield wiper and washer switch . . . . . . . . . . . . . . . 2-24
Switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Rear window wiper and washer switch. . . . . . . . . . . . . . 2-25

Rear window and outside mirror (if so equipped) defroster switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Headlight and turn signal switch. . . . . . . . . . . . . . . . . . . . 2-26
Headlight control switch. . . . . . . . . . . . . . . . . . . . . . . . 2-26
Daytime running light system (Canada only) . . . . . . 2-27
Instrument brightness control . . . . . . . . . . . . . . . . . . . 2-28
Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Fog light switch (if so equipped) . . . . . . . . . . . . . . . . 2-29
Off road lamps switch (if so equipped) . . . . . . . . . . . 2-29
Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . 2-30
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Vehicle Dynamic Control (VDC) OFF switch . . . . . . . . . 2-31
Hill descent control switch (if so equipped). . . . . . . . . . 2-31
Electronic locking rear differential (E-Lock) system switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Clutch interlock (clutch start) switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Storage trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Console box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

Sunglasses holder (if so equipped) . . . . . . . . . . . . . . 2-36
Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Seat pockets (if so equipped). . . . . . . . . . . . . . . . . . . 2-37
Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Cargo area storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Luggage hooks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Cargo nets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

Roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45
Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47
Map lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48
Cargo light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-48

INSTRUMENT PANEL

2-2 Instruments and controls

WIC1447

1. 2.

3.

4.

Vents (P. 4-2) Headlight/fog light (if so equipped)/turn signal switch (P. 2-26) Steering wheel switch for audio control (if so equipped)/Bluetooth姞 Hands- Free Phone System (if so equipped) (P. 4-35, P. 4-37) Driver supplemental air bag/horn (P. 1-44, P. 2-30)

5. Meters, gauges and warning/indicator

6.

lights (P. 2-3, 2-12) Cruise control main/set switches (P. 5-18)

7. Windshield wiper/washer switch and

rear window wiper/washer switch (P. 2-24, P. 2-25) Storage (P. 2-35) Audio system controls (P. 4-17)

8. 9. 10. Front passenger supplemental air bag

(P. 1-44)

11. Upper and lower glove box (P. 2-36) 12. Passenger air bag status light (P. 1-53) 13. Auxiliary audio input jack (if so equipped) (P. 4-33)

14. Power outlet (P. 2-34)

15. Electronic locking rear differential

(E-Lock) system switch (if so equipped) (P. 2-32) Hill descent control switch (if so equipped) (P. 2-31) Vehicle Dynamic Control (VDC) OFF switch (P. 2-31)

16. Shift selector (P. 5-12) 17. 4WD shift switch (if so equipped)

(P. 5-21)

18. Climate controls (P. 4-2, P. 4-9) 19. Hazard warning flasher switch (P. 2-30) 20. 21. Tilt steering wheel control (P. 3-12) 22. Off road lamps switch (if so equipped)

Ignition switch (P. 5-9)

(P. 2-29)

23. Clutch interlock (clutch start) switch

(if so equipped) (P. 2-33)

24. Power outside mirror controls

(if so equipped) (P. 3-14)

See the page number indicated in paren- theses for operating details.

METERS AND GAUGES

1. Warning/indicator lights 2. 3. 4. 5.

Tachometer Speedometer Fuel gauge Voltmeter

WIC0911
6. Odometer/Twin trip odometer/Trip com-

puter (if so equipped) Engine oil pressure gauge Engine coolant temperature gauge

7. 8.

Instruments and controls 2-3

SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition switch is placed in the ON position. The odometer records the total distance the ve- hicle has been driven. The twin trip odometer records the distance of individual trips.

LIC0780

With twin trip odometer

Changing the display: For vehicles equipped with twin trip odometer, pushing the change button changes the display as follows:

Trip

→ Trip

→ Trip

Speedometer

1. 2. Odometer 3. Change button

WIC0912

2-4 Instruments and controls

TRIP COMPUTER (if so equipped) The display of the trip computer is situated in the speedometer display. When the ignition switch is placed in the ON position, the display scrolls all the modes of the trip computer and then shows the mode chosen before the ignition switch was placed in the OFF position.

When the ignition switch is placed in the ON position, modes of the trip computer can be selected by pushing the trip computer change button. The following modes can be selected: Distance to empty (dte—mile or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly be- ing calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.

The display is updated every 30 seconds.

The dte mode includes a low range warning feature: when the fuel level is low, the dte mode is automatically selected and the digits blink in or- der to draw the driver’s attention. Press the change button if you wish to return to the mode that was selected before the warning occurred. The dte mark (dte) will remain blinking until the vehicle is refueled.

When the fuel display will change to (----).

level drops even lower, the dte

NOTE: ● If the amount of fuel added while the ignition switch is OFF is small, the dis- play just before the ignition switch is turned OFF may continue to be dis- played.

● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display.

Average speed (MPH or km/h) The average speed mode shows the average vehicle speed since last reset. Resetting is done by pressing the change button for more than approximately 1 second. The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows (----).

Instruments and controls 2-5

LIC0781

With trip computer

For vehicles equipped with trip computer, push- ing the change button changes the display as follows:

→ Trip

→ Distance to Empty → Trip Average speed → Average fuel consumption → Journey time → Trip For additional puter” later in this section. Resetting the trip odometer: Pushing the change button for more than 1 sec- ond resets the currently displayed trip odometer to zero.

information, refer to “Trip com-

Average fuel consumption (Mpg or l/100km) The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pressing the change button for more than approximately 1 second. The dis- play is updated every 30 seconds. At about the first 1/3 miles (500 m) after a reset, the display shows (----). Journey time The journey time mode shows the time since the last reset. The displayed time can be reset by pressing the change button for more than ap- proximately 1 second. Trip computer reset Pushing the change button for more than 3 sec- onds will reset all modes except Trip A and dis- tance to empty (dte).

2-6 Instruments and controls

LIC0738

TACHOMETER The tachometer indicates engine speed in revo- lutions per minute (rpm). Do not rev the engine into the red zone 䊊1 .

CAUTION

When engine speed approaches the red zone, shift to a higher gear or reduce en- gine speed. Operating the engine in the red zone may cause serious engine damage.

LIC0739
ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range 䊊1 when the gauge needle points within the zone shown in the illustration.

The engine coolant temperature varies with the outside air temperature and driving conditions.

CAUTION

If the gauge indicates coolant tempera- ture near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the nor- mal range, stop the vehicle as soon as safely possible. If the engine is over- heated, continued operation of the ve- hicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required.

The located on the driver’s side of the vehicle.

indicates that the fuel-filler door is

CAUTION

● If

the vehicle runs out of

fuel, Malfunction Indicator Light the (MIL) may come on. Refuel as soon as possible. After a few driving trips, light should turn off. If the the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.

● For additional information, see “Mal- function Indicator Light (MIL)” later in this section.

LIC0740

FUEL GAUGE The gauge indicates the approximate fuel level in the tank.

The gauge may move slightly during braking, turning, acceleration, or going up or down hills.

The gauge needle returns to E (Empty) after the ignition switch is placed in the OFF position.

The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge regis- ters E (Empty).

Instruments and controls 2-7

CAUTION

● This gauge is not designed to indicate low engine oil level. Use the dipstick to check the oil level. (See “Engine oil” in the “Maintenance and do-it-yourself” section.)

● If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine.

LIC0741

ENGINE OIL PRESSURE GAUGE The gauge indicates the engine lubrication sys- tem oil pressure while the engine is running. The needle should be in the middle of the gauge when the engine is running.

2-8 Instruments and controls

WIC1299

VOLTMETER When the ignition switch is placed in the ON position, the voltmeter indicates the battery volt- age. When the engine is running, it indicates the generator voltage. While cranking the engine, the volts drop below the normal range. If the needle is not in the normal range (11 – 15 volts) 䊊1 while the engine is running, it may indicate that the charging system is not functioning properly. Have the system checked by a NISSAN dealer.

COMPASS DISPLAY (if so equipped)

This unit measures terrestrial magnetism and in- dicates heading direction of vehicle. With the ignition switch in the ON position, press the button as described in the fallowing chart to activate various features of the automatic anti-glare rearview mirror.

Push and hold the button for about: 1 second

8 seconds

11 seconds

13 seconds

Feature: (Push button again for about 1 sec- ond to change settings)

Compass display toggles on/off Automatic anti-glare/indicator light toggles on/off Compass zone can be changed to correct false compass readings Compass enters calibration mode

For more information about the automatic anti- glare feature, refer to “Automatic anti-glare rear- view mirror” in the “Pre-driving checks and ad- justments” section.

You can also calibrate the compass by driving your vehicle on your everyday route. The com- pass will be calibrated once it has tracked three complete circles.

WIC0904

COMPASS DISPLAY button for about 1 second when Push the the ignition key is in the ON position to toggle the outside temperature and compass direction dis- play 䊊1 on or off. The display will indicate the direction of the vehicle’s heading. N: North E: East S: South W: West If the “CAL” or “C” icon is illuminated in the compass display, calibrate the compass by driv- ing the vehicle in three complete circles at less than 5 MPH (8 km/h).

Instruments and controls 2-9

Zone variation change procedure The difference between magnetic north and geo- graphical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens:

1. Press and hold the

button for about 11 seconds. The current zone number will appear in the display. Release the button.

2. Find your current location on the zone map.

Refer to the illustration.

3. Press the

button repeatedly to toggle through the zone numbers until the desired number appears in the display. Once you have selected a zone number, the display will show a compass direction within a few seconds.

Inaccurate compass direction

The compass display is equipped with automatic correction function. If the correct direction is not shown, follow this procedure. 1. With the display turned on, press and hold button for about 13 seconds. The the “CAL” icon in the compass display will illu- minate.

2-10 Instruments and controls

WIC0355

2. Calibrate the compass by driving the vehicle in three complete circles at a maximum speed of 5 MPH (8 km/h).

3. After completing the circles,

the display

should return to normal.

CAUTION

● Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet. They affect the op- eration of the compass.

● When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing.

Instruments and controls 2-11

WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS

or

Anti-lock Braking System (ABS) warning light

Automatic transmission oil temperature warning light (if so equipped)

Automatic transmission park warning light

model)

or

Brake warning light

Low windshield washer fluid warning light

Hill descent control system on indicator light (if so equipped)

Seat belt warning light and chime

Malfunction Indicator Light (MIL)

Supplemental air bag warning light

Overdrive OFF indicator light (A/T models only)

Automatic transmission position indicator light (A/T models only)

Security indicator light

Charge warning light

Cruise main switch indicator light

Slip indicator light

Door open warning light

Cruise set switch indicator light

Transfer 4LO position indicator light

model)

Engine oil pressure warning light

Electronic locking rear differential (E-Lock) sys- tem on indicator light (if so equipped)

Turn signal/hazard indicator lights

4WD warning light (

model)

4WD shift indicator light (

model)

Vehicle Dynamic Control OFF indicator light

Low fuel warning light

Front passenger air bag status light

Low tire pressure warning light

High beam indicator light (Blue)

2-12 Instruments and controls

CHECKING BULBS With all doors closed, apply the parking brake and place the ignition switch in the ON position without starting the engine. The following lights will come on:

or

The following lights come on briefly and then go off:

or

If any light fails to come on, it may indicate an open circuit in the electrical system. Have the system repaired promptly. WARNING LIGHTS

or

Anti-lock Braking System (ABS) warning light

When the ignition switch is placed in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational.

If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock func- tion is turned off. The brake system then operates normally, but without anti-lock assistance. See “Brake system” in the “Starting and driving” sec- tion.

Automatic transmission oil temperature warning light (if so equipped)

This light comes on when the automatic transmis- sion oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off.

CAUTION

Continued vehicle operation when the A/T oil temperature warning light is on may damage the automatic transmission.

Automatic transmission park model) warning light (

WARNING

● If the ATP light is ON, this indicates that the automatic transmission P (Park) po- sition will not function and the transfer case is in neutral.

● When parking, always make sure that the 4WD shift indicator light illuminates and the parking brake is set. Failure to engage the transfer position in 2WD, 4H or 4LO could result in the vehicle mov- ing unexpectedly, resulting in serious personal injury or property damage.

● Shift the 4WD switch into the 2WD, 4H or 4LO position again to turn off the ATP warning light when the shift selector is in the P position and the ATP warning light is ON. (Before shifting the 4WD switch into the 4LO position, move the shift selector into the N position once, shift the shift selector into P again and make sure the ATP warning light is OFF.)

Instruments and controls 2-13

This light indicates that the automatic transmis- sion parking function is not engaged. If the trans- fer control is not secured in any drive position while the shift selector is in the P (Park) position, the transmission will disengage and the drive wheels will not lock.

or

Brake warning light

This light functions for both the parking brake and the foot brake systems. Parking brake indicator

When the ignition switch is placed in the ON position, the light comes on when the parking brake is applied. Low brake fluid warning light When the ignition switch is placed in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the ve- hicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See “Brake fluid” in the “Main- tenance and do-it-yourself” section of this manual. If the brake fluid level is correct, have the warning system checked by a NISSAN dealer.

2.

2-14 Instruments and controls

WARNING

CAUTION

● Your brake system may not be working properly if the warning light is on. Driv- ing could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driv- ing it could be dangerous.

● Pressing the brake pedal with the en- gine stopped and/or a low brake fluid level may increase your stopping dis- tance and braking will require greater pedal effort as well as pedal travel.

● If the brake fluid level

is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.

Charge warning light

If this light comes on while the engine is running, it may indicate the charging system is not func- tioning properly. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light remains on, see a NISSAN dealer immediately.

● Do not ground electrical accessories directly to the battery terminal. Doing so will bypass the variable control sys- tem and the vehicle battery may not charge completely. Refer to “Variable voltage control system” in the “Mainte- nance and do-it-yourself” section later in this manual.

● Do not continue driving if the generator

belt is loose, broken or missing. Door open warning light

This light comes on when any of the doors are not closed securely while the ignition switch is placed in the ON position.

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.

The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See “Engine oil” in the “Maintenance and do-it-yourself” section of this manual.

CAUTION

Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.

4WD warning light ( model)

The 4WD warning light comes on when the igni- tion switch is turned to ON. It turns off soon after the engine is started.

If the engine or vehicle is not functioning properly, the warning light will either remain illuminated or blink. See “4WD warning light” in the “Starting and driving” section.

CAUTION

Low fuel warning light

● If the warning light comes on or blinks during operation, have your vehicle checked by a NISSAN dealer as soon as possible.

● Do not drive on dry hard surface roads in the 4H or 4LO position. If the 4WD warning light turns on when you are driving on dry hard surface roads: – in the 4H position, shift the 4WD shift

switch to 2WD.

– in the 4LO position for automatic transmission models, stop the ve- hicle and shift the shift selector to the N position with the brake pedal depressed and shift the 4WD shift switch to 2WD.

– in the 4LO position for manual trans- mission models, stop the vehicle and shift the shift selector to the N posi- tion with the clutch pedal depressed and shift the 4WD shift switch to 2WD,

● If the warning light is still on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.

This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is conve- nient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).

Low tire pressure warning light

Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare. The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly. After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off. Low tire pressure warning: If the vehicle is being driven with low tire pressure, the warning light will illuminate. When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure of all 4 tires to the recom- mended COLD tire pressure shown on the Tire and Loading Information label located Instruments and controls 2-15

in the driver’s door opening. The low tire pressure warning light does not automati- cally turn off when the tire pressure is ad- justed. After the tire is inflated to the rec- ommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pres- sure gauge to check the tire pressure.

For additional information, see “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section and in the “In case of emergency” section. TPMS malfunction:

If the TPMS is not functioning properly, the low tire pressure warning light will flash for approxi- mately 1 minute when the ignition switch is placed in the ON position. The light will remain on after the 1 minute. Have the system checked by a NISSAN dealer.

For additional information, see “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section and “Tire pressure” in the “Main- tenance and do-it-yourself” section.

WARNING

● If the light does not illuminate with the ignition switch placed in the ON posi- tion, have the vehicle checked by a NISSAN dealer as soon as possible.

● If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under-inflated tires may permanently damage the tires and in- crease the likelihood of tire failure. Se- rious vehicle damage could occur and may lead to an accident and could re- sult in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label located in the driver’s door opening to turn the low tire pressure warning light OFF. If the light still comes on while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, re- place it with a spare tire as soon as possible.

● When a spare tire is mounted or a wheel is replaced the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

CAUTION

● The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.

● If the vehicle is being driven at speeds of less than 16 MPH (25 km/h), the TPMS may not operate correctly.

● Be sure to install the specified size of

tires to the 4 wheels correctly.

2-16 Instruments and controls

Low windshield washer fluid warning light

Supplemental air bag warning light

This light comes on when the windshield washer fluid is at a low level. Add windshield washer fluid as necessary. See “Window washer fluid” in the “Maintenance and do-it-yourself” section of this manual.

Seat belt warning light and chime

The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition switch is placed in the ON or START position and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for about 6 seconds unless the driver’s seat belt is securely fastened.

The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied . For 7 seconds after the ignition switch is placed in the ON position, the system does not activate the warning light for the front passenger.

Refer to “Seat belts” in the “Safety—Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage.

When the ignition switch is placed in the ON or START position, the supplemental air bag warn- ing light illuminates for about 7 seconds and then turns off. This means the system is operational.

If any of the following conditions occur, the front air bag, side air bag, curtain and rollover air bag and pretensioners need servicing and your ve- hicle must be taken to a NISSAN dealer: ● The supplemental air bag warning light re-

mains on after approximately 7 seconds.

● The supplemental air bag warning light

flashes intermittently.

● The supplemental air bag warning light does

not come on at all.

Unless checked and repaired, the supplemental restraint systems (air bag system) and/or the pretensioners may not function properly. For ad- ditional details see “Supplemental restraint sys- tem” in the “Safety—Seats, seat belts and supplemental restraint system” section of this manual.

WARNING

If the supplemental air bag warning light is on, it could mean that the front air bag, side air bags, curtain and rollover air bags and/or pretensioners will not operate in an accident. To help avoid injury to your- self or others, have your vehicle checked by a NISSAN dealer as soon as possible.

INDICATOR LIGHTS

Automatic transmission position indicator light (A/T models only)

When the ignition switch is in the ON position, this indicator light shows the shift selector posi- tion. See “Driving the vehicle” in the “Starting and driving” section of this manual.

Cruise main switch indicator light

The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.

Instruments and controls 2-17

Cruise set switch indicator light

4WD shift indicator light

model)

High beam indicator light (blue)

The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning prop- erly. Have the system checked by a NISSAN dealer.

Electronic locking rear differential (E-Lock) system on indicator light (if so equipped)

This light comes on when the electronic locking rear differential (E-Lock) system clutch is fully engaged.

The indicator light flashes when the system is first turned on. When the system fully engages, the light remains on. If the switch is on and the indicator light continues to flash, the system is not engaged.

For additional information, see “Electronic lock- ing rear differential (E-Lock) system switch” later in this section and “Electronic locking rear differ- ential (E-Lock) system” in the “Starting and driv- ing” section of this manual.

2-18 Instruments and controls

The light should turn off within 1 second after placing the ignition switch in the ON position.

While the engine is running, the 4WD shift indi- cator light will illuminate the position selected by the 4WD shift switch. The 4WD shift indicator light may blink while shifting from one drive mode to the other.

Front passenger air bag status light

The front passenger air bag status light ( will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.

For front passenger air bag status light operation, see “Front passenger air bag and status light” in the “Safety — Seats, seat belts and supplemental restraint system” section of this manual.

This blue light comes on when the headlight high beams are on and goes out when the low beams are selected.

The high beam indicator light also comes on when the passing signal is activated.

Hill descent control system on indicator light (if so equipped)

When the ignition switch is placed in the ON position, this light comes on briefly and then turns off.

The light comes on when the hill descent control system is activated.

If the hill descent control switch is on and the indicator light blinks, the system is not engaged.

If the indicator light does not come on or blink when the hill descent switch is on, the system may not be functioning properly. Have the system checked by a NISSAN dealer.

For additional information, see “Hill descent con- trol switch” later in this section and “Hill descent control system” in the “Starting and driving” sec- tion of this manual.

Malfunction Indicator Light (MIL)

If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction. The Malfunction Indicator Light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 gallons (11.4 liters) of fuel in the fuel tank.

After a few driving trips, the light should turn off if no other potential emission control system malfunction exists. If this indicator light comes on steady for 20
seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control sys- tem inspection/maintenance test. See “Readi- ness for inspection/maintenance (I/M) test” in the “Technical and consumer information” section of this manual.

Operation

The Malfunction Indicator Light will come on in one of two ways: ● Malfunction Indicator Light on steady — An emission control system malfunction has been detected. Check the fuel-filler cap. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

● Malfunction Indicator Light blinking — An engine misfire has been detected which may damage the emission control system. To re- duce or avoid emission control system dam- age:

– do not drive at speeds above 45 MPH

(72 km/h).

– avoid hard acceleration or deceleration.

– avoid steep uphill grades.

– if possible, reduce the amount of cargo

being hauled or towed.

The Malfunction Indicator Light may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without hav- ing the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system.

Overdrive OFF indicator light (A/T models only)

This light comes on when the overdrive function is OFF.

The automatic transmission overdrive function is controlled by the overdrive switch.

See “Driving the vehicle” in the “Starting and driving” section of this manual.

Security indicator light

This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational.

Instruments and controls 2-19

For additional tems” later in this section.

information, see “Security sys-

Slip indicator light

This indicator light will blink when the traction control system is limiting wheel spin. Slippery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly.

The slip indicator light also comes on when you place the ignition switch in the ON position. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or does not go off, have the traction control system checked by a NISSAN dealer.

If the battery is removed or discharged, the trac- tion control system is disabled and the slip indi- cator light will not turn off after 2 seconds when the ignition switch is placed in the ON position. To reset the system, you must perform the reset procedure. Refer to “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” sec- tion of this manual.

If the light does not go off after performing the reset procedure, have the traction control system checked by a NISSAN dealer.

2-20 Instruments and controls

Transfer 4LO position indicator light (

model)

The light should turn off within 1 second after turning the ignition switch to ON. This light comes on when the 4WD shift switch is set in the 4LO position with the ignition switch in the ON position. The transfer case may be damaged if you shift the switch while driving. Make sure the transfer 4LO position indicator light turns on when you shift the 4WD shift switch to 4LO. The indicator light may blink while shifting from one drive mode to the other. The 4LO indicator light must stop blinking and remain illuminated or turn off before shifting the transmission into gear. If the shift selector is shifted from the N (Neutral) position to any other gear when the 4LO indicator light is blinking, the vehicle may move unexpectedly.

When you shift between 4H and 4LO, follow the instructions below: ● For automatic transmission models, stop the vehicle and shift the shift selector to the N (Neutral) position with the brake pedal de- pressed, then depress and turn the 4WD shift switch to 4LO or 4H.

● For manual transmission models, stop the vehicle and shift the shift selector to the N (Neutral) position with the clutch pedal de- pressed, then depress and turn the 4WD shift switch to 4LO or 4H.

You cannot move the transfer 4WD shift switch between 4H and 4LO unless you stop the vehicle and shift the shift selector to the N position with the brake pedal (AT models) or clutch pedal (MT models) depressed.

Turn signal/hazard indicator lights

The appropriate light flashes when the turn signal switch is activated. Both lights flash when the hazard switch is turned on.

Vehicle Dynamic Control OFF indicator light

This indicator light comes on when the Vehicle Dynamic Control off switch is pushed to OFF, the transfer case is in the 4LO position ( model), or when the Vehicle Dynamic Control system is not functioning properly. This indicates the Vehicle Dynamic Control system is not oper- ating.

Push the Vehicle Dynamic Control off switch again or restart the engine and the system will operate normally. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” sec- tion of this manual.

The Vehicle Dynamic Control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the Vehicle Dynamic Control system checked by a NISSAN dealer.

If the battery is removed or discharged, the Ve- hicle Dynamic Control system is disabled and the VDC indicator light will not turn off after 2 sec- onds when the ignition switch is turned to the ON position. To reset the system, you must perform the reset procedure. Refer to “Vehicle Dynamic

Control (VDC) system” in the “Starting and driv- ing” section of this manual.

If the light does not go off after performing the reset procedure, have the traction control system checked by a NISSAN dealer.

While the Vehicle Dynamic Control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal.

The VDC system will be disabled and the VDC light will illuminate when the electronic locking rear differential (E-lock) system switch (if so equipped) is turned on and the E-lock system is engaged. If the E-lock system disengages or the switch is turned off, the VDC system will be enabled and the VDC light will turn off. AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard.

Key reminder chime A chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch placed in the OFF posi- tion, a chime sounds when the driver’s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leav- ing the vehicle.

Instruments and controls 2-21

SECURITY SYSTEMS

LIC0372
Your vehicle may have two types of security sys- tems: ● Vehicle security system ● NISSAN Vehicle Immobilizer System VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs. The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Al- 2-22 Instruments and controls

ways secure your vehicle even if parking for a brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.

Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. How to arm the vehicle security system 1. Close all windows. (The system can be armed even if the windows are open.)

2. Remove the key from the ignition switch.

3. Close all doors. Lock all doors. The doors can be locked with the key, power door lock switch (if the door is opened, locked and then closed), or with the keyfob.

Keyfob operation:

● Push the

button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.

● When the

button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a re- minder that the doors are already locked.

The horn may or may not beep. Refer to “Silencing the horn beep feature” in the “Pre-driving checks and adjustments” sec- tion later in this manual.

4. Confirm that the

indicator light comes on. The light stays on for about 30
seconds. The vehicle security system is now pre-armed. After about 30 seconds the ve- hicle security system automatically shifts light begins into the armed phase. The to flash once every 3 seconds. If, during the 30-second pre-arm time period, the driver’s door is unlocked by the key or the keyfob, or the ignition switch is placed in ACC or ON position, the system will not arm.

● If the key is turned slowly when locking the driver’s door, the system may not arm. Furthermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.

● Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition switch placed in the OFF position.

Vehicle security system activation The vehicle security system will give the following alarm: ● The headlights blink and the horn sounds

intermittently.

● The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver’s door with the key or by pressing the

button on the keyfob.

The alarm is activated by: ● opening a door without using the key or keyfob (even if the door is unlocked by using the inside lock knob or the power door lock switch).

How to stop an activated alarm The alarm stops only by unlocking the driver’s door or the liftgate with the key or by pressing the

button on the keyfob.

The alarm does not stop if the ignition switch is turned to ACC or ON. NISSAN VEHICLE IMMOBILIZER SYSTEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key.

If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures:

1. Leave the ignition switch placed in the ON

position for approximately 5 seconds.

2. Place the ignition switch in the OFF or LOCK position and wait approximately 10
seconds.

3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.

If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices.

Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY — IMMOBILIZER, ANT ASSY — IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RE- SPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPER- ATE THE EQUIPMENT.

Instruments and controls 2-23

WINDSHIELD WIPER AND WASHER SWITCH

LIC0474

WIC0843

Security indicator light The security indicator light blinks whenever the ignition switch is placed in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition switch is placed in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser- vice as soon as possible. Please bring all registered keys that you have when visiting your NISSAN dealer for service. 2-24 Instruments and controls

SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position.

Push the lever down to operate the wiper at the following speed: 䊊1

Intermittent (INT) — intermittent operation can be adjusted by turning the knob toward 䊊A (Slower) or 䊊B (Faster). 䊊2
Low (LO) — continuous low speed operation 䊊3 High (HI) — continuous high speed opera-

tion

Push the lever up 䊊4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you 䊊5
to operate the washer. The wiper will also operate several times.

WARNING

In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.

CAUTION

● Do not operate the washer continu-

ously for more than 30 seconds.

● Do not operate the washer if the reser-

voir tank is empty.

● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.

REAR WINDOW WIPER AND WASHER SWITCH

● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.

WIC0844
The rear window wiper and washer operate when the ignition switch is in the ON position.

Turn the switch clockwise from the OFF position to operate the wiper. 䊊1

Intermittent (INT) – intermittent operation (not adjustable)

䊊2 ON – continuous low speed operation Push the switch forward 䊊3
to operate the washer. The wiper will also operate several times.

WARNING

In freezing temperatures the washer solu- tion may freeze on the window and ob- scure your vision. Warm the rear window with the defroster before you wash the rear window.

CAUTION

● Do not operate the washer continu-

ously for more than 30 seconds.

● Do not operate the washer if the reser-

voir tank is empty.

● Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.

● Pre-mix washer fluid concentrates with water to the manufacturer’s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.

Instruments and controls 2-25

REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH

HEADLIGHT AND TURN SIGNAL SWITCH

Type A

Type B

Type A

LIC0783

LIC1419

LIC0706

To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster indicator light comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes.

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.

2-26 Instruments and controls

HEADLIGHT CONTROL SWITCH Lighting 䊊1 When turning the switch to the

posi- tion, the front parking, tail, license plate and instrument panel lights come on. 䊊2 When turning the switch to the

posi- tion, the headlights come on and all the other lights remain on.

After the headlights automatically turn off with the headlight switch in the position, the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the position.

or

or

LIC0688

WIC0859

Type B

CAUTION

Use the headlights with the engine run- ning to avoid discharging the vehicle battery.

Headlight beam select 䊊1 To select the high beam function, push the lever forward. The high beam lights come on and the

light illuminates.

䊊2 Pull the lever back to select the low beam. 䊊3 Pulling and releasing the lever flashes the

headlight high beams on and off.

Battery saver system If the ignition switch is placed in the OFF position while the headlight switch is in the or 5 minutes.

position, the headlights will turn off after

CAUTION

Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position for full illumination when driving at night.

Instruments and controls 2-27

If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is placed in the OFF position.

WARNING

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

2-28 Instruments and controls

WIC0917

WIC0860

INSTRUMENT BRIGHTNESS CONTROL The instrument brightness control operates when the headlight control switch is in the or Turn the control 䊊A to adjust the brightness of instrument panel lights when driving at night.

position.

TURN SIGNAL SWITCH Turn signal 䊊1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.

Lane change signal 䊊2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.

WIC0861
FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the To turn the fog lights off, turn the fog light switch to the OFF position. The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected.

position.

LIC1448

OFF ROAD LAMPS SWITCH (if so equipped) The off road lights are designed to increase vis- ibility when driving during off road conditions. To turn on the off road lights: ● The covers must be removed from the off

road lights.

● The headlights must be set to the high beam

function.

● Press the off road lamps switch.

To turn the off road lights off, press the off road lamps switch again. If the high beam function of the headlights is turned off at any time, the off road lights will turn off as well. If the high beam function is turned back on, the off road lamps switch needs to be pressed again with the covers still removed in order to turn on the off road lights. The covers should remain on the off road lights when the lights are not in use.

Instruments and controls 2-29

HAZARD WARNING FLASHER SWITCH

HORN

The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.

LIC0394
Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash.

WARNING

● If stopping for an emergency, be sure to

move the vehicle well off the road.

● Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.

● Turn signals do not work when the haz-

ard warning flasher lights are on.

2-30 Instruments and controls

WIC1449
To sound the horn, push the area between the horn icons on the steering wheel.

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.

VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH

HILL DESCENT CONTROL SWITCH (if so equipped)

WIC0534
The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driv- ing conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn on the system. See “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” section.

indicator will come on.

LIC0743

WARNING

● Never rely solely on the hill descent control system to control vehicle speed when driving on steep downhill grades. Always drive carefully when using the hill descent control system and decel- erate the vehicle speed by depressing the brake pedal if necessary. Be espe- cially careful when driving on frozen, muddy or extremely steep downhill roads. Failure to control vehicle speed may result in a loss of control of the vehicle and possible serious injury or death.

● The hill descent control may not control the vehicle speed on a hill under all load or road conditions. Always be prepared to depress the brake pedal to control vehicle speed. Failure to do so may re- sult in a collision or serious personal injury.

CAUTION

When the hill descent control system op- erates continuously for a long time, the temperature of the brake pads may in- crease and the hill descent control system may be temporarily disabled (the indicator light will blink). If the indicator light does not come on continuously after blinking, stop using the system.

The hill descent control system is designed to reduce driver workload when going down steep hills. The hill descent control system helps to control vehicle speed so the driver can concen- trate on steering the vehicle.

To activate the hill descent control system: ● the 4WD switch must be in the 4L position and the vehicle speed must be under 15
mph (25 km/h) or

Instruments and controls 2-31

ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped)

LIC0729
The Electronic Locking Rear Differential (E-Lock) system can help provide added traction if the vehicle is stuck or becoming stuck. To activate the E-Lock system: ● the 4WD switch must be in the 4LO position

(4-wheel drive vehicles),

● the vehicle must be stopped or moving at 4

mph (7 km/h) or less, and

● the E-Lock system switch must be turned

ON.