Download PDF Manual

ing the force that the seatback receives from the occupant in a rear-end collision. The movement of the head restraint helps support the occu- pant(cid:146)s head by reducing its backward movement and helping absorb some of the forces that may lead to whiplash type injuries. Active Head Restraints are effective for collisions at low to medium speeds in which it is said that whiplash injury occurs most. Active Head Restraints operate only in certain rear-end collisions. After the collision, the head restraints return to their original positions. Properly adjust the Active Head Restraints as described earlier in this section. FLEXIBLE SEATING


WARNING


c Never allow anyone to ride in the cargo area or on the rear seats when they are in the fold-down position. In a collision, people riding in these areas without proper restraints are more likely to be seriously injured or killed.


c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly.


c Do not fold down the rear seats when occupants are in the rear seat area or any luggage is on the rear seats.


c Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Always replace and adjust them prop- erly if they have been removed for any reason.


c If the head restraints are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident.


c When returning the seatbacks to the upright position, be certain they are completely secured in the latched posi- tion. If they are not completely secured, passengers may be injured in an acci- dent or sudden stop.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-5


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury.


LRS0608
Folding the front passenger(cid:146)s seatback (if so equipped) To fold the front passenger(cid:146)s seatback flat for extra storage length when transporting long items: s1 Slide the seat to the rearmost position. Lift up on the recline lever, located on the out- side edge of the seat, and fold the seatback forward as far as it will go. Then lift up on the latch located on the upper corner of the seatback to release the back of the seat.


LRS0609
s2 Once the seatback is released it will enable you to fold the front passenger seatback flat over the seat cushion.


3. To return the front passenger(cid:146)s seat to a seating position lift up on the seatback and push it up to an upright position. Then pull up on the recline lever and lean the seatback to a proper seating position. Release the lever to lock the seatback in position.


1-6 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WARNING


c If you fold the front passenger(cid:146)s seat- back flat forward to carry longer ob- jects, be sure this cargo is properly se- cured and not near an air bag. In a crash, an inflating air bag might force that object toward a person. This could cause severe injury or even death. Se- cure objects away from the area in which an air bag would inflate. See (cid:147)Precautions on supplemental restraint system(cid:148) later in this section.


c Never allow anyone to ride in the cargo area or on the front passenger(cid:146)s seat when it is in the fold-down position. Use of these areas by passengers could re- sult in serious injury in an accident or sudden stop.


LRS0577


Folding the 2nd row bench seat To fold the 2nd row bench seat flat for maximum cargo hauling:


s1 Disconnect and secure the center seat belt and tongues into the retractor base. See (cid:147)Stowing the center seat belt(cid:148) later in this section. Then properly stow the outboard seat belts in the seat belt hooks before fold- ing down the rear seats. See (cid:147)Seat belt hook(cid:148) in this section for more information. Lower the head restraints to the full (cid:147)down(cid:148) position. Pull the strap forward, located in the center of each seat cushion, and fold each seat cushion toward the front of the vehicle.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-7


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


LRS0578
s2 Then pull the straps located on the outside edge of each seatback to fold the seatbacks forward.


s3 This provides a level cargo floor.


LRS0579


LRS0580
s4 To return the bench seats to a seating posi- tion reverse this process. Raise the seat- backs to an upright position. Make sure to hold the seat belts above the seat cushion, then push the seat cush- ion down into place.


1-8 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


LRS0585


Removing the 2nd row bench seat cushions The rear seat cushion can be removed to provide additional space when folding the 2nd row seat- backs flat. To remove the 2nd row bench seat cushions:


1. Pull the straps forward, located in the center of each seat cushion to fold the seat cush- ions forward.


2. Lift up and fold each of the red release handles on the seat base toward the front of the vehicle. The will release the seat cushion from the seat base.


c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.


c When returning the seatbacks to the upright position, be certain they are completely secured. If they are not com- pletely secured in the latched position, passengers may be injured in an acci- dent or sudden stop.


c If the seat cushions are removed for any reason, they should be securely stored to prevent them from causing injury to passengers or damage to the vehicle in case of sudden braking or an accident.


3. Then lift up on the seat cushion to remove it from the seat base. Be sure to store it in a secure place.


To return the rear seat back to a seating position:


1. Push the anchor bars on the bottom of the


seat cushions down into the seat base.


2. Rotate the seat cushion toward the rear of the vehicle and push down until they are folded flat to secure each seat cushion to the seat base. Make sure to hold the seat belts above the seat cushion and prop- erly push the seat cushion down into place.


WARNING


c Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an acci- dent or sudden stop.


c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. Never ride in the rear seat unless the seat bottom cushions are in place and latched.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-9


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


SEAT BELTS


SSS0136


PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supple- mental air bag. Most U.S. states and Canadian provinces or territories specify that seat belts be worn at all times when a vehicle is being driven.


1-10 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint.


SSS0134


SSS0016


WARNING


c The seat belt should be properly ad- justed to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an acci- dent. Serious injury or death can occur if the seat belt is not worn properly.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-11


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c Be sure the seat belt tongue is securely


fastened to the proper buckle.


c Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness.


c Do not allow more than one person to


use the same seat belt.


c Never carry more people in the vehicle


than there are seat belts.


c If the seat belt warning light glows con- tinuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indicate a mal- function in the system. Have the system checked by a NISSAN dealer.


c Once a seat belt pretensioner has acti- vated, it cannot be reused and must be replaced together with the retractor. See your NISSAN dealer.


c Removal and installation of preten- sioner system components should be done by a NISSAN dealer.


SSS0014


WARNING


c Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. c Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident.


1-12 Safety(cid:151)Seats, seat belts and supplemental restraint system


and


attaching


c All seat belt assemblies, including re- tractors hardware, should be inspected after any collision by a NISSAN dealer. NISSAN recom- mends that all seat belt assemblies in use during a collision be replaced un- less the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. c All child restraints and attaching hard- ware should be inspected after any col- lision. Always follow the restraint manufacturer(cid:146)s inspection instructions and replacement recommendations. The child restraints should be replaced if they are damaged.


CHILD SAFETY Children need adults to help protect them. They need to be properly restrained.


In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations. Every child is different, so be sure to learn the best way to transport your child.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


There are three basic types of child restraint systems: c Rear facing child restraint c Front facing child restraint c Booster seat The proper restraint depends on the child(cid:146)s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child re- straints are available for children who outgrow rear facing child restraints and are at least 1 year old. Booster seats are used to help position a vehicle lap/shoulder belt on a child who can no longer use a front facing child restraint.


WARNING


Infants and children need special protec- tion. The vehicle(cid:146)s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fit- ting seat belt could cause serious or fatal injury. Always use appropriate child restraints.


All U.S. states and Canadian provinces or terri- tories require the use of approved child restraints for infants and small children. See (cid:147)Child Re- straints(cid:148) later in this section.


Also, there are other types of child restraints available for larger children for additional protec- tion. NISSAN recommends that all pre-teens and children be restrained in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat.


Small Children Children that are over one year old and weigh at least 20 lbs (9 kg) can be placed in a forward facing child restraint. Refer to the manufacturer(cid:146)s instructions for minimum and maximum weight and height recommendations. NISSAN recom- mends that small children be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint that fits your vehicle and always follow the manufacturer(cid:146)s instructions for installation and use. Larger children Children who are too large for child restraints should be seated and restrained by the seat belts which are provided. The seat belt may not fit properly if the child is less than 4 feet 9 inches (142.5 cm) tall and weighs between 40 lbs (18
kg) and 80 lbs (36 kg). A booster seat should be used to obtain proper seat belt fit. NISSAN recommends that a child be placed in a commercially available booster seat if the shoul- der belt in the child(cid:146)s seating position fits close to the face or neck or if the lap portion of the seat belt goes across the abdomen. The booster seat should raise the child so that the shoulder belt is properly positioned across the top, middle por- Safety(cid:151)Seats, seat belts and supplemental restraint system 1-13


This is especially important because your vehicle has a supplemental restraint sys- tem (Air bag system) for the front passen- ger. See (cid:147)Supplemental restraint system(cid:148) later in this section. Infants Infants up to at least 1 year old should be placed in a rear facing child restraint. NISSAN recom- mends that infants be placed in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint that fits your vehicle and always follow the manu- facturer(cid:146)s instructions for installation and use.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


tion of the shoulder and the lap belt is low on the hips. A booster seat can only be used in seating positions that have a three-point type seat belt. The booster seat should fit the vehicle seat and have a label certifying that it complies with Fed- eral Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.


WARNING


Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop. PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as pos- sible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations.


INJURED PERSONS NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations. THREE-POINT TYPE SEAT BELT WITH RETRACTOR


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times.


c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.


c For the most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat with both feet on the floor and adjust the seat belt properly.


1-14 Safety(cid:151)Seats, seat belts and supplemental restraint system


WRS0174


Manual front seat shown


Fastening the seat belts s1 Adjust the seat. See (cid:147)Seats(cid:148) earlier in this


section.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts.


The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation.


When the ALR mode is activated, the seat belt cannot be extended again until the seat belt tongue is detached from the buckle and fully retracted. The seat belt returns to the ELR mode after the seat belt fully retracts. See (cid:147)Child re- straints(cid:148) later in this section for more information. The ALR mode should be used only for child restraint installation. During normal seat belt use by a passenger, the ALR mode should not be activated. If it is activated it may cause uncomfortable seat belt ten- sion. It can also change the operation of the front passenger air bag. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.


LRS0594
s2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.


c The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.


c If the seat belt cannot be pulled from its fully retracted position, firmly pull the belt and release it. Then smoothly pull the belt out of the retractor.


LRS0595
s3 Position the lap belt portion low and snug


on the hips as shown.


s4 Pull the shoulder belt portion toward the retractor to take up extra slack. Be sure the shoulder belt is routed over your shoulder and across your chest.


The front passenger seat and the rear seating positions three-point seat belts have two modes of operation: c Emergency Locking Retractor (ELR) c Automatic Locking Retractor (ALR)


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-15


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WARNING


When fastening the seat belts, be certain that the seatbacks are completely se- cured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop.


To increase your confidence in the seat belts, check the operation as follows. c Grasp the shoulder belt and pull forward quickly. The retractor should lock and re- strict further belt movement.


If the retractor does not lock during this check or if you have any questions about seat belt opera- tion, see a NISSAN dealer.


WRS0139


Unfastening the seat belts s1 To unfasten the seat belt, press the button on the buckle. The seat belt automatically re- tracts.


Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate methods: c When the seat belt is pulled quickly from the


retractor.


c When the vehicle slows down rapidly.


1-16 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


SSS0240


SSS0241


Center of the rear bench seat The center seat belt has a connector tongues1
and a seat belt tongue s2 . Both the connector tongue and the seat belt tongue must be securely latched for proper seat belt operation.


WARNING


c Always fasten the connector tongue


and the seat belt in the order shown.


c Always make sure both the connector tongue and the seat belt tongue are secured when using the seat belt. Do not use it with only the seat belt tongue attached. This could result in serious personal injury in case of an accident or a sudden stop.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-17


LRS0601


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sud- den stop.


Stowing the center seat belt


When folding down the rear seat, the rear center seat belt can be retracted into a stowed position as follows: 1. Hold the connector tongue s1 so that the seat belt does not retract suddenly when the tongue is released from the connector buckle. Insert a suitable tool such as a key sA into the connector buckle and release the con- nector tongue s1 .


2.


3. Fold the connector as illustrateds2 . 4. Then secure the connector tongue into the


retractor bases3 in the ceiling.


WARNING


c Do not unfasten the rear center seat belt connector except when folding down the rear seat.


c When attaching the rear center seat belt connector, be certain that the seat- backs are completely secured in the latched position and the rear center seat belt connector is completely secured.


1-18 Safety(cid:151)Seats, seat belts and supplemental restraint system


LRS0602


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


Attaching the center seat belt Always be sure the center seat belt connector tongue and connector buckle are attached. Dis- connect only when folding down the rear seat. To connect the buckle: s1 Pull out the seat belt tongue from the retrac-


tor base. s2 Pull out


the connector


tongue from the


molded retractor base.


s3 Pull the seat belt and secure the receiver


buckle until it clicks.


The center seat belt connector tongue and re- ceiver buckle are indicated by the > and < mark. The center seat belt connector tongue can be attached only into the rear center seat belt con- nector buckle. To fasten the seat belt, see (cid:147)Fastening the seat belt(cid:148) earlier in this section.


WARNING


c Do not unfasten the rear center seat belt connector except when folding down the rear seat.


c When attaching the rear center seat belt connector, be certain that the seat- backs are completely secured in the latched position and the rear center seat belt connector is completely secured.


c If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sud- den stop.


LRS0611


2nd row center seat belt comfort guide When using the 2nd row center seat belt it may be necessary to use the comfort guide to adjust the shoulder belt height for occupants of different sizes for added comfort and to help obtain proper seat belt fit. 1. Raise the head restraint on the 2nd row driver(cid:146)s side seating position. Remove the comfort guide from the stowed position by pulling the cord from the channel.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-19


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


2.


LRS0610
Insert the shoulder belt into the back of the comfort guide so that the seat belt lays flat in the guide. Be sure that the comfort guide routes the seat belt properly over the center of your shoulder and across your chest. The belt should be away from your face and neck, but not falling off of your shoulder.


LRS0612
3. To return the seat belt comfort guide to the stowed position, route the comfort guide strap in the channel under the 2nd row driv- er(cid:146)s side seating position head restraint and attach the guide in the clip.


LRS0242


Front and 2nd row outboard seats


Shoulder belt height adjustment (front and 2nd row outboard seats) The shoulder belt anchor height should be ad- justed to the position best for you. (See (cid:147)Precau- tions on seat belt usage(cid:148) earlier in this section.) To adjust, pull out s1 the adjustment button and move the shoulder belt anchor s2 to the desired position, so the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Re- lease the adjustment button to lock the shoulder belt anchor into position.


1-20 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WARNING


c After adjustment, release the adjust- ment button and try to move the shoul- der belt anchor up and down to make sure it is securely fixed in position.


c The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effec- tiveness of the entire restraint system and increase the chance or severity of injury in an accident.


WARNING


c Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts.


c Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.


c Never use seat belt extenders to install child restraints. If the child restraint is not secured properly, the child could be seriously injured in a collision or a sud- den stop.


SEAT BELT MAINTENANCE c To clean the seat belt webbing, apply a mild soap solution or any solution recom- mended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry.


c If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.


LRS0583


Seat belt hook When the seat belt is not in use and when folding down the rear seats, hook the rear seat belts on the seat belt hooks. SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The ex- tender adds approximately 8 in (200 mm) of length and may be used for either the driver or front passenger seating position. See a NISSAN dealer for assistance if an extender is required.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-21


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


CHILD RESTRAINTS


c Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt as- sembly should be replaced.


PRECAUTIONS ON CHILD RESTRAINTS


ARS1098


WRS0256


WARNING


c Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death.


c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


1-22 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An in- flating front air bag could seriously in- jure or kill your child. A rear-facing child restraint must only be used in the rear seat.


c NISSAN recommends that the child re- straint be installed in the rear seat. Ac- cording to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If you must install a front facing child re- straint in the front seat, see (cid:147)Child re- straint installation using the seat belts(cid:148) later in this section.


c Improper use or improper installation of a child restraint can increase the risk or severity of injury for both the child and other occupants of the vehicle and can lead to serious injury or death in an accident.


c Follow all of the child restraint manu- facturer(cid:146)s instructions for installation and use. When purchasing a child re- straint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.


c If the child restraint is not anchored properly, the risk of a child being in- jured in a collision or a sudden stop greatly increases.


c Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


c Adjustable seatbacks should be posi- tioned to fit the child restraint, but as upright as possible.


c After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the seat near the LATCH attachment or by the seat belt path. Try to tug it forward and check to see if the belt holds the re- straint in place. The child restraint should not move more than 1 inch (25
mm). If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.


c When your child restraint is not in use, keep it secured with the LATCH System or a seat belt to prevent it from being thrown around in case of a sudden stop or accident.


CAUTION


Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.


This vehicle is equipped with a universal child restraint lower anchor system, referred to as the Lower Anchors and Tethers for CHildren System or LATCH. Some child restraints include two rigid or webbing-mounted attachments that can be connected to these lower anchors. For details, see the (cid:147)Lower Anchors and Tethers for CHildren System (LATCH)(cid:148) later in this section.


If you do not have a LATCH compatible child restraint, the vehicle seat belts can be used. See (cid:147)Child restraint installation using the seat belts(cid:148) later in this section. In general, child restraints are also designed to be installed with the lap portion of a lap/shoulder seat belt.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-23


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


Several manufacturers offer child restraints for infants and small children of various sizes. When selecting any child restraint, keep the following points in mind: c Choose only a restraint with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.


c Check the child restraint in your vehicle to be sure it is compatible with the vehicle(cid:146)s seat and seat belt system.


c If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjustments to be sure the child restraint is compatible with your child. Choose a child restraint that is designed for your child(cid:146)s height and weight. Always follow all recommended procedures. All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated.


WRS0438


LRS0589


LATCH system anchor locations


LOWER ANCHORS AND TETHERS FOR CHILDREN SYSTEM (LATCH) Your vehicle is equipped with special anchor points that are used with Lower Anchors and Tethers for CHildren System (LATCH) compat- ible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child restraint. The LATCH anchor points are provided to install child restraints in the rear outboard seating posi- tions only. Do not attempt to install a child restraint in the center position using the LATCH anchors.


LATCH label locations


LATCH lower anchor point locations The LATCH anchors are located at the rear of the seat cushion near the seatback. A label is at- tached to the seatback to help you locate the LATCH anchors.


WARNING


c Attach LATCH compatible child re- straints only at the locations shown in the illustration. If a child restraint is not secured properly, your child could be seriously injured or killed in an accident.


1-24 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


LATCH lower anchor location


LATCH webbing-mounted attachment


LATCH rigid-mounted attachment


WRS0700


LRS0661


LRS0662


c Do not secure a child restraint in the center rear seating position using the LATCH anchors. The child restraint will not be secured properly.


c Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstance are they to be used for adult seat belts or harnesses.


Installing child restraint LATCH anchor attachments LATCH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. With this sys- tem, you do not have to use a vehicle seat belt to secure the child restraint. Check your child re- straint for a label stating that it is compatible with LATCH. This information may also be in the in- structions provided by the child restraint manu- facturer.


LATCH child restraints generally require the use of a top tether strap. See (cid:147)Top tether strap child restraint(cid:148) later in this section for installation in- structions. When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. See (cid:147)Child restraint installation using LATCH(cid:148) in this section.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-25


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


If you have any questions when installing a top tether strap child restraint on the rear seat, consult your NISSAN dealer for de- tails.


TOP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point.


WARNING


c Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


c Do not allow cargo to contact the top tether strap when it is attached to the top tether anchor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or cargo that contacts the top tether strap may damage it during a collision. Your child could be seriously injured or killed in a collision if the top tether strap is damaged.


Top Tether Anchor Point Locations Anchor points are located on the back of each seatback for all three seating positions of the 2nd row bench seat as shown.


1-26 Safety(cid:151)Seats, seat belts and supplemental restraint system


LRS0588


2nd row bench seat


Installing top tether strap First, secure the child restraint with the LATCH system (rear outboard seat positions only) or the seat belt, as applicable.


1. Top tether strap


2. Anchor point


For the 2nd row bench seat, install the top tether strap as follows:


1. Position the top tether strap over the top of the head restraint with the head restraint in the full (cid:147)down(cid:148) position.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LATCH anchors, such as seat belt webbing or seat cush- ion material. The child restraint will not be secured properly if the LATCH an- chors are obstructed.


Front-facing Follow these steps to install a front-facing child restraint using LATCH: 1. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions.


2. Secure the tether strap to the tether anchor point on the seat directly behind the child restaint.


3. Tighten the tether strap according to the manufacturer(cid:146)s instructions to remove any slack.


For best child restraint fit, see the child restraint installation instructions in this section and the child restraint manufacturer(cid:146)s instructions. CHILD RESTRAINT INSTALLATION USING LATCH


WARNING


c Attach LATCH compatible child re- straints only at the locations shown. For the LATCH lower anchor locations, see (cid:147)Lower Anchors and Tethers for CHil- dren System (LATCH)(cid:148) in this section. If a child restraint is not secured properly, your child could be seriously injured or killed in an accident.


c The LATCH anchors are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstance are they to be used for adult seat belts or harnesses.


LRS0663


Front facing web-mounted (cid:150) step 2


2. Secure the child restraint anchor attach- ments to the LATCH lower anchors. Check to make sure the LATCH attachment is prop- erly attached to the lower anchors.


3. The back of the child restraint should be


secured against the vehicle seat back.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-27


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


LRS0664


LRS0671


WRS0697


Front facing rigid-mounted (cid:150) step 2


If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See (cid:147)Head restraint adjustment(cid:148) in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child re- straint.


Front facing (cid:150) step 4


Front facing (cid:150) step 6


4. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See (cid:147)Top tether strap child restraint(cid:148) in this section.


5.


6. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.


1-28 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


is loose,


7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 3
through 6. Rear-facing Follow these steps to install a rear-facing child restraint using LATCH System: 1. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions.


Rear facing web-mounted (cid:150) step 2


Rear facing rigid-mounted (cid:150) step 2


LRS0665


LRS0666


2. Secure the child restraint anchor attach- ments to the LATCH lower anchors. Check to make sure the LATCH attachment is prop- erly attached to the lower anchors.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-29


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 2
through 4.


is loose,


Rear facing (cid:150) step 3


Rear facing (cid:150) step 4


LRS0673


LRS0674


3. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.


4. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.


1-30 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


The instructions in this section apply to child restraint installation using the vehicle seat belts in the rear seat or the front passenger seat.


c NISSAN recommends that child re- straints be installed in the rear seat. However, if you must install a forward facing child restraint in the front pas- senger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF. See (cid:147)Front passenger air bag and status light(cid:148) later in this sec- tion for details.


c The three-point seat belt in your vehicle is equipped with an Automatic Locking Retractor (ALR) which must be used when installing a child restraint.


c Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or otherwise be unsecured and cause in- jury to the child in a sudden stop or collision. Also, it can change the opera- tion of the front passenger air bag. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.


c A child restraint with a top tether strap should not be used in the front passen- ger seat.


WRS0256


CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS


WARNING


c Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front passenger seat. Front air bags inflate with great force. A rear-facing child restraint could be struck by the front air bag in a crash and could seriously injure or kill your child.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-31


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


2. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions


The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See (cid:147)Head restraint adjust- ment(cid:148) in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed. If the seating position does not have an adjustable head re- straint and it is interfering with the proper child restraint fit, try another seating position or a dif- ferent child restraint.


WRS0680


Front facing (cid:150) step 3


3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer(cid:146)s in- structions for belt routing.


WRS0699
Front-facing (front passenger seat) (cid:150) step 1
Front-facing Follow these steps to install a front-facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat: 1. If you must install a child restraint in the front seat, it should be placed in a front-facing direction only. Move the seat to the rearmost position. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.


1-32 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


Front facing (cid:150) step 4


Front facing (cid:150) step 5


Front facing (cid:150) step 6


LRS0667


LRS0668


WRS0681


4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.


5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.


6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-33


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint. If you are unable to properly secure the restraint, move the restraint to another seating position and try again, or try a differ- ent child restraint. Not all child restraints fit in all types of vehicles.


9. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the ALR mode.


10. Check to make sure the child restraint is properly secured prior to each use. If the seat belt locked, repeat steps 3
through 8.


is not


WRS0698


Front facing (cid:150) step 7


7.


If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See (cid:147)Top tether strap child restraint(cid:148) in this section. Do not install child restraints that require the use of a top tether strap to seating positions that do not have a top tether anchor.


1-34 Safety(cid:151)Seats, seat belts and supplemental restraint system


11.


WRS0475


Front facing (cid:150) step 11


If the child restraint is installed in the front passenger seat, turn the ignition switch to the ON position. The front passenger air bag should illuminate. If this status light light is not illuminated see 9Front passenger air bag and status light9 in this section. Move the child restraint to another seating position. Have system checked by a NISSAN dealer.


the


After the child restraint is removed and the seat belt is fully retracted, the ALR mode (child re- straint mode) is canceled.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WRS0256


WRS0761


LRS0669


Rear-facing (cid:150) step 1


Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. Position the child restraint on the seat. Always follow the restraint manufacturer(cid:146)s instructions.


Rear facing (cid:150) step 2


Rear facing (cid:150) step 3


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer(cid:146)s in- structions for belt routing.


3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-35


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


Rear facing (cid:150) step 4


Rear facing (cid:150) step 5


Rear facing (cid:150) step 6


LRS0670


WRS0762


WRS0763


4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.


5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt.


6. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint. If you are unable to properly secure the restraint, move the restraint to another rear seating position and try again, or try a different child restraint. Not all child re- straints fit in all types of vehicles.


1-36 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


BOOSTER SEATS


7. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retrac- tor is in the ALR mode.


8. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 7.


After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled.


ARS1098


PRECAUTIONS ON BOOSTER SEATS


WARNING


c Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint or booster seat can result in serious injury or death.


c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


c NISSAN recommends that the booster seat be installed in the rear seat. Ac- cording to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If you must install a booster seat in the front seat, see (cid:147)Booster seat installa- tion(cid:148) in this section.


seating


position


c A booster seat must only be installed in lap/shoulder belt. Failure to use a three-point type seat belt with a booster seat can result in a serious in- jury in sudden stop or collision.


that


has


c Improper use or improper installation of a booster seat can increase the risk or severity of injury for both the child and other occupants of the vehicle and can lead to serious injury or death in an accident.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-37


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c Do not use towels, books, pillows or other items in place of a booster seat. Items such as these may move during normal driving or a collision and result in serious injury or death. Booster seats are designed to be used with a lap/shoulder belt. Booster seats are de- signed to properly route the lap and shoulder portions of the seat belt over the strongest portions of a child(cid:146)s body to provide the maximum protection dur- ing a collision.


c Follow all of the booster seat manufac- turer(cid:146)s instructions for installation and use. When purchasing a booster seat, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of booster seats in your vehicle.


c If the booster seat and seat belt is not used properly, the risk of a child being injured in a collision or a sudden stop greatly increases.


c Adjustable seatbacks should be posi- tioned to fit the booster seat, but as upright as possible.


c After placing the child in the booster seat and fastening the seat belt, make sure the shoulder portion of the belt is away from the child(cid:146)s face and neck and the lap portion of the belt does not cross the abdomen.


c Do not put the shoulder belt behind the child or under the child(cid:146)s arm. If you must install a booster seat in the front seat, see (cid:147)Booster seat installation(cid:148) later in this section.


c When your booster seat is not in use, keep it secured with a seat belt to pre- vent it from being thrown around in case of a sudden stop or accident.


CAUTION


Remember that a booster seat left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the booster seat.


1-38 Safety(cid:151)Seats, seat belts and supplemental restraint system


LRS0455
Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: c Choose only a booster seat with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.


c Check the booster seat in your vehicle to be sure it is compatible with the vehicle(cid:146)s seat and seat belt system.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


BOOSTER SEAT INSTALLATION


WARNING


NISSAN recommends that booster seats be installed in the rear seat. However, if you must install a booster seat in the front passenger seat, move the passenger(cid:146)s seat to the rearmost position.


CAUTION


Do not use the lap/shoulder belt Auto- matic Locking Retractor mode when using a booster seat with the seat belts.


Follow these steps to install a booster seat in the rear seat or in the front passenger seat:


LRS0464
All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated. The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat.


LRS0453
c Make sure the child(cid:146)s head will be properly supported by the booster seat or vehicle seat. The seat back must be at or above the center of the child(cid:146)s ears. For example, if a low back booster seat s1 is chosen, the vehicle seat back must be at or above the center of the child(cid:146)s ears. If the seat back is lower than the center of the child(cid:146)s ears, a high back booster seat s2 should be used. c If the booster seat is compatible with your vehicle, place your child in the booster seat and check the various adjustments to be sure the booster seat is compatible with your child. Always follow all recommended pro- cedures.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-39


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WRS0699
1. If you must install a booster seat in the front seat, move the seat to the rear- most position.


2. Position the booster seat on the seat. Only place it in a front facing direction. Always follow the booster seat manufacturer(cid:146)s in- structions.


Rear center position


Rear outboard position


LRS0591


LRS0586


3. The booster seat should be positioned on the vehicle seat so that it is stable. If neces- sary, adjust or remove the head restraint to obtain the correct booster seat fit. See (cid:147)Head restraint adjustment(cid:148) earlier in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the booster seat is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper booster seat fit, try another seating position or a different booster seat.


1-40 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


4. Position the lap portion of the seat belt low and snug on the child(cid:146)s hips. Be sure to follow the booster seat manufacturer(cid:146)s in- structions for adjusting the belt routing.


5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child(cid:146)s shoulder. Be sure to follow the booster seat manufacturer(cid:146)s instructions for adjusting the belt routing.


LRS0454


Front passenger position


6. Follow the warnings, cautions and instruc- tions for properly fastening a seat belt shown in the (cid:147)Three-point seat belt with retractor(cid:148) earlier in this section.


7.


WRS0475
If the booster seat is installed in the front passenger seat, turn the ignition switch to the ON position. The front passenger air bag status light may or may not illuminate, depending on the size of the child and the type of booster seat being used. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-41


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


SUPPLEMENTAL RESTRAINT SYSTEM


PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) sec- tion contains important information concerning the following systems: c Driver and passenger supplemental front- impact air bag (NISSAN Advanced Air Bag System)


c Front seat-mounted side-impact supple-


mental air bag


c Roof-mounted curtain side-impact and roll-


Roof-mounted curtain side-impact and rollover supplemental air bag system (if so equipped): This system can help cushion the impact force to the head of occupants in front and rear outboard seating positions in certain side impact or rollover collisions. In a side impact, the curtain and rollover air bags are designed to inflate on the side where the vehicle is impacted. In a rollover, both curtain and rollover air bags are designed to inflate and remain inflated for a short time. These supplemental restraint systems are de- signed to supplement the crash protection pro- vided by the seat belts and are not a substitute for them. Seat belts should always be correctly worn and the occupant seated a suitable dis- tance away from the steering wheel, instrument panel and door finishers. See (cid:147)Seat belts(cid:148) earlier in this section for instructions and precautions on seat belt usage. The supplemental air bags operate only when the ignition switch is in the ON or START position. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.


over supplemental air bag c Seat belt with pretensioner Supplemental front-impact air bag system: The NISSAN Advanced Air Bag System can help cushion the impact force to the head and chest of the driver and front passenger in certain frontal collisions. Front seat-mounted side-impact supple- mental air bag system (if so equipped): This system can help cushion the impact force to the chest area of the driver and front passenger in certain side impact collisions. The side air bags are designed to inflate on the side where the vehicle is impacted. 1-42 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


c The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt us- age then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.


c The front passenger seat is equipped with an occupant classification sensor (pressure sensor) that turns the front passenger air bag OFF under some conditions. This sensor is only used in this seat. Failure to be properly seated and wearing the seat belt can increase the risk or severity of injury in an acci- dent. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.


c Keep hands on the outside of the steer- ing wheel. Placing them inside the steering wheel rim could increase the risk that they are injured when the front air bag inflates.


WARNING


c The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity fron- tal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. c The front passenger air bag will not inflate if the passenger air bag status light is lit or if the front passenger seat is unoccupied. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.


WRS0031


c The seat belts and the front air bags are most effective when you are sitting well back and upright in the seat. The front air bags inflate with great force. Even with the NISSAN Advanced Air Bag Sys- tem, if you are unrestrained, leaning forward, sitting sideways or out of posi- tion in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the front air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practi- cal from the steering wheel or instru- ment panel. Always use the seat belts.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-43


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


ARS1133


ARS1041


WARNING


c Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.


1-44 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


ARS1042


ARS1043


ARS1044


WARNING


c Children may be severely injured or killed when the front air bags, side air bags or curtain and rollover air bags inflate if they are not properly re- strained. Pre-teens and children should be properly restrained in the rear seat, if possible.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-45


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


ARS1045


WRS0256


WRS0431


WARNING


c Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An in- flating front air bag could seriously in- jure or kill your child. See (cid:147)Child re- straints(cid:148) earlier in this section for details.


Do not lean against the door.


WARNING


Front seat-mounted side-impact supple- mental air bags (if so equipped) and roof- mounted curtain side-impact and rollover supplemental air bags (if so equipped): c The side air bags and curtain and roll- over air bags ordinarily will not inflate in the event of a frontal impact, rear im- pact, or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.


1-46 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WARNING


c The seat belts, the side air bags and curtain and rollover air bags are most effective when you are sitting well back and upright in the seat. The side air bag and curtain and rollover air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails. Do not allow anyone sitting in the front seats or rear outboard seats to extend their hand out of the window or lean against the door. Some examples of dangerous riding positions are shown in the previous illustrations.


WRS0365
Do not lean against doors or windows.


SSS0162
Do not lean against doors or windows.


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-47


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


WRS0363


SSS0159


WARNING


c When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations.


c Do not use seat covers on the front seatbacks. They may interfere with side air bag inflation.


1-48 Safety(cid:151)Seats, seat belts and supplemental restraint system


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


1.


2.


3. 4.


Roof-mounted curtain side-impact and rollover supplemental air bag inflators (if so equipped) Roof-mounted curtain side-impact and rollover supplemental air bags (if so equipped) Air bag Control Unit (ACU) Supplemental front-impact air bag mod- ules


5. Crash zone sensor 6. Occupant classification system control


unit


7. Occupant classification sensor (pres-


sure sensor) Satellite sensors 8. 9. Seat belt buckle switches 10. Seat belt with pretensioner 11. Front seat-mounted side-impact


supplemental air bag modules (if so equipped)


LRS0593


Safety(cid:151)Seats, seat belts and supplemental restraint system 1-49


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


usage for the driver. For the front passenger, it additionally monitors the weight of an occupant or object on the seat and seat belt tension. Based on information from the sensors, only one front air bag may inflate in a crash, depending on the crash severity and whether the front occupants are belted or unbelted. Additionally, the front passenger air bag may be automatically turned OFF under some conditions, depending on the weight detected on the passenger seat and how the seat belt is used. If the front passenger air bag is OFF, the passenger air bag status light will be illuminated (if the seat is unoccupied, the light will not be illuminated, but the air bag will be off). See (cid:147)Front passenger air bag and status light(cid:148) later in this section for further details. One front air bag inflating does not indicate improper performance of the system.


NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN Ad- vanced Air Bag System for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regu- lations. It is also permitted in Canada. However, all of the information, cautions and warn- ings in this manual still apply and must be followed. The driver supplemental front-impact air bag is located in the center of the steering wheel. The passenger supplemental front-impact air bag is mounted in the dashboard above the glove box. The front air bags are designed to inflate in higher severity frontal collisions, although they may in- flate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper front air bag system opera- tion. The NISSAN Advanced Air Bag System has dual stage inflators. It also monitors information from the crash zone sensor, the Air bag Control Unit (ACU), seat belt buckle sensors, occupant clas- sification sensor (pressure sensor) and passen- ger seat belt tension sensor. Inflator operation is based on the severity of a collision and seat belt 1-50 Safety(cid:151)Seats, seat belts and supplemental restraint system


If you have any questions about your air bag system, please contact NISSAN or your NISSAN dealer. If you are considering modification of your vehicle due to a disability, you may also contact NISSAN. Contact information is contained in the front of this Owner(cid:146)s Manual.


When a front air bag inflates, a fairly loud noise may be heard, followed by the release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken to not inhale it, as it may


cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. Front air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the front occupants. They can help save lives and reduce serious injuries. However, an inflating front air bag may cause facial abrasions or other injuries. Front air bags do not provide restraint to the lower body. Even with NISSAN advanced air bags, seat belts should be correctly worn and the driver and pas- senger seated upright as far as practical away from the steering wheel or instrument panel. The front air bags inflate quickly in order to help protect the front occupants. Because of this, the force of the front air bag inflating can increase the risk of injury if the occupant is too close to, or is against, the front air bag module during inflation. The front air bags deflate quickly after a collision. The front air bags operate only when the ignition switch is in the ON or START posi- tion. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.


Z REVIEW COPY—2008 Xterra (xtr) Owners Manual—USA_English (nna) 06/26/07—debbie X


Front passenger air bag and status light


WRS0475


WARNING


The front passenger air bag is designed to automatically turn OFF under some con- ditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is nec- essary for most effective protection. Fail- ure to follow all instructions in this manual concerning the use of seats, seat belts and child restraints can increase the risk or severity of injury in an accident.


Status light


is The front passenger air bag status light located near the climate controls. The light oper- ates as follows: c Unoccupied passenger(cid:146)s seat: The


is OFF and the front passenger air bag is OFF and will not inflate in a crash.


c Passenger(cid:146)s seat occupied by a small adult, child or child restraint as outlined in this illuminates to indicate section: The that the front passenger air bag is OFF and will not inflate in a crash.


c Occupied passenger seat and the passen- ger meet the conditions outlined in this sec- tion: The light is OFF to indicate that the front passenger air bag is operational.


Front passenger air bag The front passenger air bag is designed to auto- matically turn OFF when the vehicle is operated under some conditions as described below in accordance with U.S. regulations. If the front passenger air bag is OFF, it will not inflate in a crash. The driver air bag and other air bags in your vehicle are not part of this system. The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such


as children, by requiring the air bag to be auto- matically turned OFF. Certain sensors are used to meet the requirements.


Loading...
x