Download PDF Manual

the vehicle runs out of


fuel, malfunction indicator light the (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.


c For additional information, see (cid:147)Mal- function indicator light (MIL)(cid:148) later in this section.


LIC0740


FUEL GAUGE The gauge indicates the approximate fuel level in the tank.


The gauge may move slightly during braking, turning, acceleration, or going up or down hills.


The gauge needle returns to E (Empty) after the ignition key is turned to OFF.


The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge regis- ters E (Empty).


Instruments and controls 2-7


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


CAUTION


c This gauge is not designed to indicate low engine oil level. Use the dipstick to check the oil level. (See (cid:147)Engine oil(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section.)


c If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine.


LIC0741


ENGINE OIL PRESSURE GAUGE The gauge indicates the engine lubrication sys- tem oil pressure while the engine is running.


2-8 Instruments and controls


WIC0913


VOLTMETER When the ignition key is turned to the ON posi- tion, the voltmeter indicates the battery voltage. When the engine is running, it indicates the gen- erator voltage. While cranking the engine, the volts drop below the normal range. If the needle is not in the normal range (11 (cid:150) 15 volts) s1 while the engine is running, it may indicate that the charging system is not functioning properly. Have the system checked by a NISSAN dealer.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS


or


Anti-lock Braking System (ABS) warning light


Automatic transmission oil temperature warn- ing light (if so equipped)


Automatic transmission park warning light


model)


Low windshield washer fluid warning light


Hill descent control system on indicator light (if so equipped)


Seat belt warning light and chime


Malfunction indicator light (MIL)


Supplemental air bag warning light


Overdrive off indicator light (automatic trans- mission models only)


or


Brake warning light


Automatic transmission position indicator light


Security indicator light (if so equipped)


Charge warning light


Door open warning light


Cruise main switch indicator light (if so equipped)


Slip indicator light for models with ABLS (if so equipped)


Cruise set switch indicator light (if so equipped)


Slip indicator light for models with VDC (if so equipped)


Engine oil pressure warning light


Electronic locking rear differential (E-Lock) system on indicator light (if so equipped)


Transfer 4LO position indicator light


model)


4WD warning light (


model)


4WD shift indicator light (


model)


Turn signal/hazard indicator lights


Low fuel warning light


Front passenger air bag status light


Vehicle dynamic control off indicator light


Low tire pressure warning light


High beam indicator light (Blue)


Instruments and controls 2-9


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights will come on: or


The following lights come on briefly and then go off:


or


If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly. WARNING LIGHTS


or


Anti-lock Braking System (ABS) warning light


When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational.


2-10 Instruments and controls


If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock func- tion is turned off. The brake system then operates normally, but without anti-lock assistance. See 9Brake system9 in the 9Starting and driving9 sec- tion.


Automatic transmission oil temperature warning light (if so equipped)


This light comes on when the automatic transmis- sion oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off.


CAUTION


Continued vehicle operation when the A/T oil temperature warning light is on may damage the automatic transmission.


Automatic transmission park warning light ( model)


WARNING


c If the ATP light is ON, this indicates that the automatic transmission P (Park) po- sition will not function and the transfer case is in neutral.


c When parking, always make sure that the 4WD shift indicator light illuminates and the parking brake is set. Failure to engage the transfer position in 2WD, 4H or 4LO could result in the vehicle mov- ing unexpectedly, resulting in serious personal injury or property damage.


c Shift the 4WD switch into the 2WD, 4H or 4LO position again to turn off the ATP warning light when the automatic trans- mission selector lever is in the P posi- tion and the ATP warning light is ON. (Before shifting the 4WD switch into the 4LO position, move the automatic transmission selector lever into the N position once, shift the selector lever into P again and make sure the ATP warning light is OFF.)


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


This light indicates that the automatic transmis- sion parking function is not engaged. If the trans- fer control is not secured in any drive position while the automatic transmission selector lever is in the P (Park) position, the transmission will disengage and the drive wheels will not lock.


or


Brake warning light


This light functions for both the parking brake and the foot brake systems. Parking brake indicator


When the ignition key is in the ON position, the light comes on when the parking brake is applied. Low brake fluid warning light


When the ignition key is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:


1. Check the brake fluid level. Add brake fluid as necessary. See (cid:147)Brake fluid(cid:148) in the (cid:147)Main- tenance and do-it-yourself(cid:148) section of this manual.


2.


If the brake fluid level is correct, have the warning system checked by a NISSAN dealer.


WARNING


CAUTION


c Your brake system may not be working properly if the warning light is on. Driv- ing could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driv- ing it could be dangerous.


c Pressing the brake pedal with the en- gine stopped and/or a low brake fluid level may increase your stopping dis- tance and braking will require greater pedal effort as well as pedal travel.


c If the brake fluid level


is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.


Charge warning light


If this light comes on while the engine is running, it may indicate the charging system is not func- tioning properly. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light remains on, see a NISSAN dealer immediately.


c Do not ground electrical accessories directly to the battery terminal. Doing so will bypass the variable control sys- tem and the vehicle battery may not charge completely. Refer to (cid:147)Variable voltage control system(cid:148) in the (cid:147)Mainte- nance and do-it-yourself(cid:148) section later in this manual.


c Do not continue driving if the generator


belt is loose, broken or missing. Door open warning light


This light comes on when any of the doors are not closed securely while the ignition key is in the ON position.


Engine oil pressure warning light


This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.


Instruments and controls 2-11


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See (cid:147)Engine oil(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.


CAUTION


Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.


4WD warning light ( model)


The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started.


If the engine or vehicle is not functioning properly, the warning light will either remain illuminated or blink. See (cid:147)4WD warning light(cid:148) in the (cid:147)Starting and driving(cid:148) section.


2-12 Instruments and controls


CAUTION


c If the warning light comes on or blinks during operation, have your vehicle checked by a NISSAN dealer as soon as possible.


c Do not drive on dry hard surface roads in the 4H or 4LO position. If the 4WD warning light turns on when you are driving on dry hard surface roads: (cid:150) in the 4H position, shift the 4WD shift


switch to 2WD.


(cid:150) in the 4LO position for automatic transmission models, stop the ve- hicle and shift the transmission se- lector lever to the N position with the brake pedal depressed and shift the 4WD shift switch to 2WD.


(cid:150) in the 4LO position for manual trans- mission models, stop the vehicle and shift the transmission shift lever to the N position with the clutch pedal depressed and shift the 4WD shift switch to 2WD.


c If the warning light is still on after the above operation, have your vehicle checked by a NISSAN dealer as soon as possible.


Low fuel warning light


This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is conve- nient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).


Low tire pressure warning light


Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare. The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly. After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off. Low tire pressure warning: If the vehicle is being driven with low tire pres- sure, the warning light will illuminate. When the low tire pressure warning light illumi- nates, you should stop and adjust the tire pres- sure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recom- mended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.


For additional information, see (cid:147)Tire Pressure Monitoring System (TPMS)(cid:148) in the (cid:147)Starting and driving(cid:148) section and in the (cid:147)In case of emergency(cid:148) section. TPMS malfunction:


If the TPMS is not functioning properly, the low tire pressure warning light will flash for approxi- mately 1 minute when the ignition switch is placed in the ON position. The light will remain on after the 1 minute. Have the system checked by a NISSAN dealer.


information, see (cid:147)Tire Pressure For additional Monitoring System (TPMS)(cid:148) in the (cid:147)Starting and driving(cid:148) section.


WARNING


CAUTION


c If


the light


illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Se- rious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still comes on while driving after adjust- ing the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.


c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indi- cated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.


c The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.


c If the vehicle is being driven at speeds of less than 16 MPH (25 km/h), the TPMS may not operate correctly.


c Be sure to install the specified size of


tires to the 4 wheels correctly.


Low windshield washer fluid warning light


This light comes on when the windshield washer fluid is at a low level. Add windshield washer fluid as necessary. See (cid:147)Window washer fluid(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.


Seat belt warning light and chime


The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver(cid:146)s seat belt is fastened. At the same time, the chime sounds for about 6 seconds unless the driver(cid:146)s seat belt is securely fastened.


Instruments and controls 2-13


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


The seat belt warning light may also illuminate if the front passenger(cid:146)s seat belt is not fastened when the front passenger(cid:146)s seat is occupied . For 7 seconds after the ignition switch is in the ON position, the system does not activate the warn- ing light for the front passenger. Refer to (cid:147)Seat belts(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint system(cid:148) section for precautions on seat belt usage.


c The supplemental air bag warning light does


not come on at all.


Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pre- tensioner seat belts may not function properly. For additional details see (cid:147)Supplemental restraint system(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint system(cid:148) section of this manual.


WARNING


If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag (if so equipped), curtain side-impact and rollover air bag systems (if so equipped) and/or pre-tensioner seat belt systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.


Supplemental air bag warning light


the following conditions occur,


When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the supplemental front air bags, supplemental side air bags (if so equipped), curtain side-impact and rollover air bags (if so equipped), and pre- tensioner seat belt systems need servicing and your vehicle must be taken to a NISSAN dealer: c The supplemental air bag warning light re-


mains on after approximately 7 seconds.


c The supplemental air bag warning light


flashes intermittently.


2-14 Instruments and controls


INDICATOR LIGHTS


Automatic transmission position indicator light


When the ignition key is turned to the ON posi- tion, this indicator light shows the automatic transmission selector lever position. See (cid:147)Driving the vehicle(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.


Cruise main switch indicator light (if so equipped)


The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.


Cruise set switch indicator light (if so equipped)


The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning prop- erly. Have the system checked by a NISSAN dealer.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


Electronic locking rear differential (E-Lock) system on indicator light (if so equipped)


This light comes on when the electronic locking rear differential (E-Lock) system clutch is fully engaged.


The indicator light flashes when the system is first turned on. When the system fully engages, the light remains on. If the switch is on and the indicator light continues to flash, the system is not engaged.


For additional information, see (cid:147)Electronic lock- ing rear differential (E-Lock) system switch(cid:148) later in this section and (cid:147)Electronic locking rear differ- ential (E-Lock) system(cid:148) in the (cid:147)Starting and driv- ing(cid:148) section of this manual.


4WD shift indicator light


model)


The light should turn off within 1 second after turning the ignition switch to ON.


While the engine is running, the 4WD shift indi- cator light will illuminate the position selected by the 4WD shift switch.


The 4WD shift indicator light may blink while shifting from one drive mode to the other.


Front passenger air bag status light


The front passenger air bag status light ( will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.


For front passenger air bag status light operation, see (cid:147)Front passenger air bag and status light(cid:148) in the (cid:147)Safety (cid:151) Seats, seat belts and supplemental restraint system(cid:148) section of this manual.


High beam indicator light (blue)


This blue light comes on when the headlight high beams are on and goes out when the low beams are selected.


The high beam indicator light also comes on when the passing signal is activated.


Hill descent control system on indicator light (if so equipped) When the ignition switch is turned ON, this light comes on briefly and then turns off.


The light comes on when the hill descent control system is activated.


If the hill descent control switch is on and the indicator light blinks, the system is not engaged.


If the indicator light does not come on or blink when the hill descent switch is on, the system may not be functioning properly. Have the system checked by a NISSAN dealer.


For additional information, see (cid:147)Hill descent con- trol switch(cid:148) later in this section and (cid:147)Hill descent control system(cid:148) in the (cid:147)Starting and driving(cid:148) sec- tion of this manual.


Malfunction indicator light (MIL)


If this indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction.


The malfunction indicator light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 gallons (11.4
liters) of fuel in the fuel tank.


After a few driving trips, the light should turn off if no other potential emission control system malfunction exists.


Instruments and controls 2-15


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


If this indicator light comes on steady for 20
seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control sys- tem inspection/maintenance test. See (cid:147)Readi- ness for inspection/maintenance (I/M) test(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual. Operation


The malfunction indicator light will come on in one of two ways: c Malfunction indicator light on steady (cid:151) An emission control system malfunction has been detected. Check the fuel-filler cap. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.


c Malfunction indicator light blinking (cid:151) An en- gine misfire has been detected which may damage the emission control system. To re- duce or avoid emission control system dam- age:


2-16 Instruments and controls


(cid:150) do not drive at speeds above 45 MPH


(72 km/h).


See (cid:147)Driving the vehicle(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.


(cid:150) avoid hard acceleration or deceleration.


Security indicator light


(cid:150) avoid steep uphill grades.


(cid:150) if possible, reduce the amount of cargo


being hauled or towed.


The malfunction indicator light may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.


CAUTION


Continued vehicle operation without hav- ing the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system.


Overdrive off indicator light (automatic transmission models only)


This light comes on when the overdrive function is OFF.


The automatic transmission overdrive function is controlled by the overdrive switch.


This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational.


For additional tems(cid:148) later in this section.


information, see (cid:147)Security sys-


Slip indicator light for models with ABLS (if so equipped)


This indicator light comes on if the active brake limited slip is activated. If activated, the system will apply braking to the slipping drive wheel(s), giving the non-slipping wheel(s) more traction. Slip indicator light for models with VDC (if so equipped)


This indicator light will blink when the traction control system is limiting wheel spin. Slippery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly. The slip indicator light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


operational. If the light does not come on or does not go off, have the traction control system checked by a NISSAN dealer.


If the battery is removed or discharged, the trac- tion control system is disabled and the slip indi- cator light will not turn off after 2 seconds when the ignition switch is turned to the ON position. To reset the system, you must perform the reset procedure. Refer to (cid:147)Vehicle dynamic control (VDC) system(cid:148) in the (cid:147)Starting and driving(cid:148) sec- tion of this manual.


If the light does not go off after performing the reset procedure, have the traction control system checked by a NISSAN dealer.


Transfer 4LO position indicator light (


model) The light should turn off within 1 second after turning the ignition switch to ON.


This light comes on when the 4WD shift switch is set in the 4LO position with the ignition key in the ON position.


The transfer case may be damaged if you shift the switch while driving.


Make sure the transfer 4LO position indicator light turns on when you shift the 4WD shift switch to 4LO.


The indicator light may blink while shifting from one drive mode to the other.


The 4LO indicator light must stop blinking and remain illuminated or turn off before shifting the transmission into gear. If the transmission selec- tor lever is shifted from the N position to any other gear when the 4LO indicator light is blinking, the vehicle may move unexpectedly.


When you shift between 4H and 4LO, follow the instructions below: c For automatic transmission models, stop the vehicle and shift the transmission selector lever to the N position with the brake pedal depressed, then depress and turn the 4WD shift switch to 4LO or 4H.


c For manual transmission models, stop the vehicle and shift the transmission selector lever to the N position with the clutch pedal depressed, then depress and turn the 4WD shift switch to 4LO or 4H.


You cannot move the transfer 4WD shift switch between 4H and 4LO unless you stop the vehicle and shift the transmission selector lever to the N position with the brake pedal (AT models) or clutch pedal (MT models) depressed.


Turn signal/hazard indicator lights


The appropriate light flashes when the turn signal switch is activated.


Both lights flash when the hazard switch is turned on.


Vehicle dynamic control off indicator light


This indicator light comes on when the vehicle dynamic control off switch is pushed to OFF, the transfer case is in the 4LO position ( model), or when the vehicle dynamic control sys- tem is not functioning properly. This indicates the vehicle dynamic control system is not operating.


Push the vehicle dynamic control off switch again or restart the engine and the system will operate normally. See (cid:147)Vehicle dynamic control (VDC) system(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.


The vehicle dynamic control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the vehicle dynamic control system checked by a NISSAN dealer.


Instruments and controls 2-17


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


If the battery is removed or discharged, the ve- hicle dynamic control system is disabled and the VDC indicator light will not turn off after 2 sec- onds when the ignition switch is turned to the ON position. To reset the system, you must perform the reset procedure. Refer to (cid:147)Vehicle dynamic control (VDC) system(cid:148) in the (cid:147)Starting and driv- ing(cid:148) section of this manual. If the light does not go off after performing the reset procedure, have the traction control system checked by a NISSAN dealer. While the vehicle dynamic control system is op- erating, you might feel slight vibration or hear the system working when starting the vehicle or ac- celerating, but this is normal. The VDC system will be disabled and the VDC light will illuminate when the electronic locking rear differential (E-lock) system switch (if so equipped) is turned on and the E-lock system is engaged. If the E-lock system disengages or the switch is turned off, the VDC system will be enabled and the VDC light will turn off.


AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings. When a disc brake pad requires replacement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime A chime sounds if the driver(cid:146)s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch in the OFF position, a chime sounds when the driver(cid:146)s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leav- ing the vehicle.


2-18 Instruments and controls


SECURITY SYSTEMS (if so equipped)


LIC0372
Your vehicle may have two types of security sys- tems: c Vehicle security system (if so equipped) c NISSAN Vehicle Immobilizer System (if so


equipped)


VEHICLE SECURITY SYSTEM (if so equipped) The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Al- ways secure your vehicle even if parking for a brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible. Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. How to arm the vehicle security system 1. Close all windows. (The system can be armed even if the windows are open.)


2. Remove the key from the ignition switch. 3. Close all doors. Lock all doors. The doors can be locked with the key, power door lock switch (if the door is opened, locked and then closed), or with the keyfob. Keyfob operation: c Push the


button on the keyfob. All doors lock. The hazard lights flash


twice and the horn beeps once to indicate all doors are locked.


c When the


button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a re- minder that the doors are already locked. The horn may or may not beep. Refer to (cid:147)Silencing the horn beep feature(cid:148) in the (cid:147)Pre-driving checks and adjustments(cid:148) sec- tion later in this manual.


4. Confirm that the


indicator light comes on. The light stays on for about 30
seconds. The vehicle security system is now pre-armed. After about 30 seconds the ve- hicle security system automatically shifts into the armed phase. The light begins to flash once every 3 seconds. If, during the 30-second pre-arm time period, the driver(cid:146)s door is unlocked by the key or the keyfob, or the ignition key is turned to ACC or ON, the system will not arm.


c If the key is turned slowly when locking the driver(cid:146)s door, the system may not arm. Furthermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.


c Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition key in the OFF posi- tion.


Vehicle security system activation The vehicle security system will give the following alarm: c The headlights blink and the horn sounds


intermittently.


c The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver(cid:146)s door with the key, or by pressing the


button on the keyfob.


The alarm is activated by: c opening a door without using the key or keyfob (even if the door is unlocked by using the inside lock knob or the power door lock switch).


How to stop an activated alarm The alarm stops only by unlocking the driver(cid:146)s door with the key, or by pressing the but- ton on the keyfob.


Instruments and controls 2-19


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY (cid:151) IMMOBILIZER, ANT ASSY (cid:151) IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RE- SPONSIBLE FOR COMPLIANCE COULD VOID THE USER(cid:146)S AUTHORITY TO OPER- ATE THE EQUIPMENT.


NISSAN VEHICLE IMMOBILIZER SYSTEM (if so equipped) The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. If the engine fails to start using a registered key (for example, when interference is caused by another registered key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following pro- cedures: 1. Leave the ignition switch in the ON position


for approximately 5 seconds.


2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds.


3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.


If the no start condition re-occurs, NISSAN rec- ommends placing the registered key on a sepa- rate key ring to avoid interference from other devices.


2-20 Instruments and controls


LIC0474


Security indicator light The security indicator light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System is operational. If the NISSAN Vehicle Immobilizer System is mal- functioning, the light will remain on while the ignition key is in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System ser- vice as soon as possible. Please bring all registered keys that you have when visiting your NISSAN dealer for service.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.


WINDSHIELD WIPER AND WASHER SWITCH


WIC0843


SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position.


Push the lever down to operate the wiper at the following speed: s1


Intermittent (INT) (cid:151) intermittent operation can be adjusted by turning the knob toward sA (Slower) or sB (Faster). s2
Low (LO) (cid:151) continuous low speed operation s3 High (HI) (cid:151) continuous high speed opera-


tion


Push the lever up s4 to have one sweep opera- tion (MIST) of the wiper. Pull the lever toward you s5
to operate the washer. The wiper will also operate several times.


WARNING


In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.


CAUTION


c Do not operate the washer continu-


ously for more than 30 seconds.


c Do not operate the washer if the reser-


voir tank is empty.


c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.


Instruments and controls 2-21


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


REAR WINDOW WIPER AND WASHER SWITCH


REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH


WIC0844
The rear window wiper and washer operate when the ignition switch is in the ON position.


Turn the switch clockwise from the OFF position to operate the wiper. s1


Intermittent (INT) (cid:150) intermittent operation (not adjustable)


s2 ON (cid:150) continuous low speed operation Push the switch forward s3
to operate the washer. The wiper will also operate several times.


2-22 Instruments and controls


WARNING


In freezing temperatures the washer solu- tion may freeze on the window and ob- scure your vision. Warm the rear window with the defroster before you wash the rear window.


CAUTION


c Do not operate the washer continu-


ously for more than 30 seconds.


c Do not operate the washer if the reser-


voir tank is empty.


c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.


c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.


LIC0783
To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster light on the switch comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes.


indicator


CAUTION


When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


HEADLIGHT AND TURN SIGNAL SWITCH


LIC0706


LIC0688


WIC0859


Type A


HEADLIGHT CONTROL SWITCH Lighting s1 When turning the switch to the


posi- tion, the front parking, tail, license plate and instrument panel lights come on. s2 When turning the switch to the


posi- tion, the headlights come on and all the other lights remain on.


Type B


CAUTION


Use the headlights with the engine run- ning to avoid discharging the vehicle battery.


Headlight beam select s1 To select the high beam function, push the lever forward. The high beam lights come on and the


light illuminates.


s2 Pull the lever back to select the low beam. s3 Pulling and releasing the lever flashes the


headlight high beams on and off.


Instruments and controls 2-23


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


Battery saver system If the ignition switch is turned OFF while the headlight switch is in the posi- tion, the headlights will turn off after 5 minutes.


or


After the headlights automatically turn off with the headlight switch in the position, the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the position.


or


or


CAUTION


Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.


DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position for full illumination when driving at night.


2-24 Instruments and controls


If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is turned off.


WARNING


When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.


WIC0917


INSTRUMENT BRIGHTNESS CONTROL The instrument brightness control operates when the headlight control switch is in the or Turn the control sA to adjust the brightness of instrument panel lights when driving at night.


position.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


HAZARD WARNING FLASHER SWITCH


WIC0860


TURN SIGNAL SWITCH Turn signal s1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.


Lane change signal s2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.


WIC0861
FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the To turn the fog lights off, turn the fog light switch to the OFF position. The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected.


position.


LIC0394


Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash.


WARNING


c If stopping for an emergency, be sure to


move the vehicle well off the road.


c Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.


c Turn signals do not work when the haz-


ard warning flasher lights are on.


Instruments and controls 2-25


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


HORN


VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH


The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.


LIC0604


To sound the horn, push the center pad area of the steering wheel.


WARNING


Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.


WIC0534
The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driv- ing conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off. To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn ON the system. See (cid:147)Vehicle dy- namic control (VDC) system(cid:148) in the (cid:147)Starting and driving(cid:148) section.


indicator will come on.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


2-26 Instruments and controls


HILL DESCENT CONTROL SWITCH (if so equipped)


LIC0743


WARNING


c Never rely solely on the hill descent control system to control vehicle speed when driving on steep downhill grades. Always drive carefully when using the hill descent control system and decel- erate the vehicle speed by depressing the brake pedal if necessary. Be espe- cially careful when driving on frozen, muddy or extremely steep downhill roads. Failure to control vehicle speed may result in a loss of control of the vehicle and possible serious injury or death.


c The hill descent control may not control the vehicle speed on a hill under all load or road conditions. Always be prepared to depress the brake pedal to control vehicle speed. Failure to do so may re- sult in a collision or serious personal injury.


CAUTION


When the hill descent control system op- erates continuously for a long time, the temperature of the brake pads may in- crease and the hill descent control system may be temporarily disabled (the indicator light will blink). If the indicator light does not come on continuously after blinking, stop using the system.


The hill descent control system is designed to reduce driver workload when going down steep hills. The hill descent control system helps to control vehicle speed so the driver can concen- trate on steering the vehicle. To activate the hill descent control system: c the automatic transmission selector lever


must be in forward or reverse gear,


c the 4WD switch must be in the 4L position and the vehicle speed must be under 15
mph (25 km/h) or


c the 4WD switch must be in the 4H position and the vehicle speed must be under 21
mph (35 km/h), and


c the hill descent control system switch must


be ON.


The hill descent control indicator light will come on when the system is activated. Also, the stop/tail lights illuminate while the hill descent control system applies the brakes to control ve- hicle speed. If the accelerator or brake pedal is depressed while the hill descent control system is on, the system will stop operating temporarily. As soon as the accelerator or brake pedal is released, the hill descent control system begins to function again if the hill descent control operating condi- tions are fulfilled. The hill descent control indicator light blinks if the switch is on and all conditions for system activa- tion are not met or if the system becomes disen- gaged for any reason. To turn off the hill descent control system, push the switch to the OFF position. For additional information, see (cid:147)Hill descent con- trol system on indicator light(cid:148) earlier in this sec- tion and (cid:147)Hill descent control system(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.


Instruments and controls 2-27


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped)


LIC0729
The Electronic Locking Rear Differential (E-Lock) system can help provide added traction if the vehicle is stuck or becoming stuck. To activate the E-Lock system: c the 4WD switch must be in the 4LO position


(4-wheel drive vehicles),


c the vehicle must be stopped or moving at 4


mph (7 km/h) or less, and


c the E-Lock system switch must be turned


ON.


2-28 Instruments and controls


When the E-Lock switch is turned ON, the indi- cator light will flash until the system engages. However, if all operation conditions listed above are not met or the system becomes disengaged, the indicator light will continue to flash.


The Anti-Lock Brake (ABS) system is disabled and the ABS light illuminates when the E-Lock system is ON. Also, the Vehicle Dynamic Control (VDC) system is disabled and the VDC light illuminates when the E-Lock system is ON.


See (cid:147)Electronic locking rear differential (E-Lock) system(cid:148) in the (cid:147)Starting and Driving(cid:148) section for further explanation and system limitations.


WARNING


c Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After us- ing the E-Lock system to free the ve- hicle, turn the system OFF.


c Use the E-Lock system only when free- ing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice sur- face. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the ve- hicle during engine braking, accelerat- ing or turning, which may result in an accident and serious personal injury.


CAUTION


c After using the E-Lock system, turn the switch OFF to prevent possible damage to driveline components from extended use.


c Do not drive over 12 MPH (20 km/h) when the system is engaged. Doing so could result in possible damage to the driveline.


c Do not turn on the E-lock system while the tires are spinning. Doing so could damage drivetrain components.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


CLUTCH INTERLOCK (clutch start) SWITCH (if so equipped)


POWER OUTLET


To use the clutch interlock switch: 1. Set the parking brake. 2. Depress the brake pedal with your right foot. 3. Place the gear shift lever in the 1 position to


move forward, or R to move backward.


4. Place your left foot on the brake pedal and


release the parking brake.


5. Turn the ignition switch to the ON position. 6. Press and release the clutch interlock switch. The CANCEL light on the switch will illuminate.


7. Turn the ignition to the START position to start the engine and, at the same time, de- press the accelerator pedal with your right foot. As the vehicle begins to move, take your left foot off the brake. Once the engine has started, the clutch interlock switch CANCEL light shuts off. Do not use the interlock switch to start the engine under normal driving conditions.


WIC0817


WARNING


Pay special attention to your surround- ings when using the clutch interlock switch. The vehicle will move forward or backward according to the gear selected.


The clutch interlock (clutch start) switch allows for starting the engine without depressing the clutch pedal. This feature helps you restart the engine if it stops under difficult conditions. (For example, the engine stops on a steep hill and a slight movement forward or backward might be dangerous.)


Front row


LIC0880


The power outlets are for powering electrical accessories such as cellular telephones.


The bottom power outlet located on instrument panel and the power outlet located in the cargo area are powered directly by the vehicle(cid:146)s battery.


The top power outlet (if so equipped)located on the instrument panel and the power outlet lo- cated inside the center console are powered only when the ignition key is in the ACC or ON posi- tion.


Open the cap to use a power outlet.


Instruments and controls 2-29


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.


c When not in use, be sure to close the cap. Do not allow water to contact the outlet.


LIC0761


LIC0862


Center console


CAUTION


c The outlet and plug may be hot during


or immediately after use.


c Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information.


c Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.


2-30 Instruments and controls


Luggage area


c Use power outlets with the engine run- ning to avoid discharging the vehicle battery.


c Avoid using power outlets when the air conditioner, headlights or rear window defroster is on.


c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


STORAGE


Top center tray


STORAGE TRAYS


WARNING


LIC0764


LIC0818


LIC0819


AT model


MT model (if so equipped)


Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop.


Instruments and controls 2-31


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


LIC0766


LIC0768


WIC0609


CONSOLE BOX Pull up on the lever s1 to open the console box lid s2 .


2-32 Instruments and controls


SUNGLASSES HOLDER (if so equipped) To open the sunglasses holder, push and release.


WARNING


c Keep the sunglasses holder closed


while driving to prevent an accident.


GLOVE BOX To open the top portion of the glove box, push the latch sA up and raise the lid. To open the lower portion of the glove box, pull the handle sB down and lower the lid. Use the master key to lock or unlock the glove box. The valet key cannot be used to lock or unlock the glove box.


WARNING


Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


CAUTION


c Do not use for anything other than


sunglasses.


c Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses.


MAP POCKETS


LIC0863


LIC0575


SEAT POCKETS A pocket is located on the back of the driver(cid:146)s seat (if so equipped). A small pocket is also located on the inboard side of the passenger(cid:146)s seat.


Instruments and controls 2-33


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


LIC0769


WIC0827


WIC0771


2nd row (rear of front console)


To open the 2nd row cup holders (rear of the front console), lower the lid. To close, raise the lid.


Front


CUP HOLDERS The front cup holders have adapters that can be removed to accommodate larger cups.


CAUTION


c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.


c Use only soft cups in the cup holder. Hard objects can injure you in an accident.


2-34 Instruments and controls


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


LIC0864


Bottle holder


CAUTION


c Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. c Do not use bottle holder for open liquid


containers.


CARGO AREA STORAGE To access the floor storage area, push down s1
to raise the handle, then pull up on the handle s2
to lift the luggage board.


Attach the tether located on the inside of the luggage board to a ceiling hook to hold the lug- gage board up while accessing the storage area.


WARNING


Do not drive with the luggage board teth- ered to a ceiling hook. In a sudden stop or collision, the luggage board could come loose and cause personal injury.


LIC0865


LUGGAGE HOOKS The luggage hooks can be used to secure cargo with ropes or other types of straps.


WARNING


c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.


c Use suitable ropes and hooks to secure


cargo.


Instruments and controls 2-35


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


c Never allow anyone to ride in the lug- gage area. It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.


c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.


c The child restraint top tether strap may be damaged by contact with items in the cargo area. Secure any items in the cargo area. Your child could be seri- ously injured or killed in a collision if the top strap is damaged.


c Be sure everyone in your vehicle is in a


seat and using a seat belt properly.


2-36 Instruments and controls


LTI0140


LTI0141


Side finisher Do not apply a load of more than 110 lb (490 N) to a single hook.


Floor hooks Do not apply a load of more than 110 lb (490 N) to a single hook.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


LIC0876


LIC0866


Cargo net (if so equipped)


CARGO NETS


WARNING


c Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury.


c Be sure to secure all four hooks into the retainers. The cargo restrained in the net must not exceed 30 lbs. (13.6 kg) or the net may not stay secured.


The cargo nets help keep packages in the cargo area from moving around while the vehicle is in motion. To install the large cargo net (if so equipped), attach the hooks to the retainers. To remove the large cargo net, detach the hooks from the cargo net retainers.


Right-hand luggage side net


The right-hand luggage side net is not removable.


WARNING


c The cargo restrained in the luggage side nets must not exceed 8.5 lb (3.9 kg) for each net or the net may not stay secured.


c Do not place sharp objects in the lug- gage side nets. Such objects may be- come dangerous projectiles and cause injury when the vehicle is moving or if the vehicle is involved in a collision.


Instruments and controls 2-37


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


LIC0867


Left-hand luggage side nets


To install the removable left-hand luggage side net sA , attach the net to the retainers. To remove, detach the net from the retainers. The smaller left-hand luggage side net is not removable.


2-38 Instruments and controls


ROOF RACK Always evenly distribute the cargo on the roof rack. The maximum total load including the gear basket is 150 lb (68 kg) evenly distrib- uted. The maximum total load for the gear basket is 30 lb (13 kg) evenly distributed. Be


WIC0868
careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Ratings (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. label (located on the driver(cid:146)s side door jamb pillar). For more information regarding GVWR and GAWR, refer to (cid:147)Vehicle loading


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


5. Always check the tightness of the crossbar


adjusting screws.


WARNING


Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, un- secured cargo could cause personal injury.


CAUTION


c Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof rack from the ground, use a ladder or stool.


c Do not place items on top of the gear basket lid. Doing so could damage the lid.


information(cid:148) in the (cid:147)Technical and consumer in- formation(cid:148) section later in this manual.


The crossbars can be adjusted or removed. Use the Torxdriver provided in the tool kit to loosen both crossbar adjusting screws.


To adjust:


1. Loosen the adjusting screws with the Torxdriver s1 by turning counterclockwise sA .


2. When the clamp is loosened, move the crossbar so the cargo can be positioned on the crossbar sB .


3. Tighten the crossbar adjusting screws with


the Torxdriver by turning clockwise.


4. Secure the cargo with rope.


5. Always check the tightness of the crossbar


adjusting screws.


To remove:


1. Loosen the adjusting screws with the Torxdriver s1 by turning counterclockwise sA .


2. Rotate the clamps sC . 3. Remove the crossbar. 4. Reverse to install.


Instruments and controls 2-39


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


To open the gear basket lid: s1 Turn the handle counterclockwise. s2 Raise the lid.


NOTE: Cargo in the gear basket must fit with the lid closed. The maximum total load for the gear basket is 30 lb (13 kg) evenly distrib- uted. Do not force the lid closed.


WARNING


The lid should be closed and locked when driving.


2-40 Instruments and controls


LIC0869


LIC0870


To remove the gear basket assembly: 1. Open the lid. 2. Loosen the 4 TorxT head fasteners with a Torxdriver by turning counterclockwise sA .


3. Lift the gear basket to remove it sB . 4. Reverse to reinstall. 5. Always check the tightness of the gear bas-


ket fasteners.


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


WINDOWS


POWER WINDOWS (if so equipped)


WARNING


c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.


The power windows operate when the ignition switch is in the ON position, or for about 45
seconds after the ignition switch is turned to the OFF position. If the driver(cid:146)s or passenger(cid:146)s door is opened during this period of about 45 sec- onds, power to the windows is canceled.


WIC0872


1. Window lock button 2. 3. 4. 5. 6.


Power door lock switch Front passenger(cid:146)s side window switch Right rear passenger(cid:146)s window switch Left rear passenger(cid:146)s window switch Driver(cid:146)s side automatic switch


Driver(cid:146)s side power window switch The driver(cid:146)s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch.


Instruments and controls 2-41


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


WIC0873


WIC0874


LIC0410


Front passenger(cid:146)s power window switch The passenger(cid:146)s window switch operates only the corresponding passenger(cid:146)s window. To open the window, push the switch and hold it down s1 . To close the window, pull the switch up s2 .


Rear power window switch The rear power window switches open or close only the corresponding windows. To open the window, push the switch and hold it down s1 . To close the window, pull the switch up s2 . Locking passengers(cid:146) windows When the window lock button is depressed, only the driver(cid:146)s side window can be opened or closed. Push it again to cancel the window lock function.


Automatic operation To fully open a window equipped with automatic operation, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening.


2-42 Instruments and controls


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna) 02/27/07—debbie X


INTERIOR LIGHTS


WIC0263


LIC0792


WIC0879


MANUAL WINDOWS The side windows can be opened or closed by turning the hand crank on each door.


Type A


The interior lights have a three-position switch and operate regardless of ignition switch posi- tion. When the switch is in the ON position s1 , the interior lights illuminate, regardless of door posi- tion. The lights will go off after about 30 minutes unless the ignition key is in the ACC or ON position.


Type B


When the switch is in the O position s2 , the interior lights will stay on for about 30 seconds when: c The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position.


c The driver(cid:146)s door is opened and then closed while the key is removed from the ignition switch.


c The key is removed from the ignition switch


while all doors are closed.


Instruments and controls 2-43


Z REVIEW COPY—2007 Xterra (xtr) Owners Manual—USA_English (nna)

Loading...
x