Download PDF Manual

vehicle with it disengaged from the holder.


2-30 Instruments and controls


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


WINDOWS


POWER WINDOWS (if so equipped)


WARNING


c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.


is opened during this period of about 45 sec- onds, power to the windows is canceled. To open a window, push the switch and hold it down. To close a window, pull the switch up. To stop the opening or closing function at any time, simply release the switch.


WIC0376


Door lock/unlock button


1. 2. Window lock button Front passenger side 3. Right rear passenger side 4. Left rear passenger side 5. 6. Driver side automatic switch


Driver(cid:146)s side power window switch The driver(cid:146)s side control panel is equipped with switches to open or close all of the windows. The power windows operate when the ignition switch is in the ON position, or for about 45
seconds after the ignition switch is turned to the OFF position. If the driver(cid:146)s or passenger(cid:146)s door


Instruments and controls 2-31


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


WIC0343
Front passenger power window switch The passenger window switch operates only the corresponding passenger window. To open the window push the switch and hold it down s1 . To close the window, pull the switch up s2 .


WIC0344


WIC0345


Rear power window switch The rear power window switches open or close only the corresponding window. To open the window, push the switch and hold it down s1 . To close the window, push the switch up s2 . Locking passengers(cid:146) windows When the window lock button is depressed, only the driver side window can be opened or closed. Push it again to cancel the window lock function.


Automatic operation To fully open the driver window, press the driver window switch down to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening.


2-32 Instruments and controls


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


SUNROOF (if so equipped)


WIC0263


WIC0346


MANUAL WINDOWS The side windows can be opened or closed by turning the hand crank on each door.


MANUAL SUNROOF Tilting the sunroof Pull the handle down s1 , then push the handle up to the fully tilted position s2 . The sunroof can- not be removed.


WARNING


c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.


c Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing.


CAUTION


c Do not open sunroof when gear basket


is in place.


c Always remove the gear basket before opening sunroof. The sunroof may be scratched if it is opened with the gear basket in place. For instructions to remove the gear basket, refer to (cid:147)Roof rack with gear basket(cid:148) in the (cid:147)Pre-driving checks and adjustments(cid:148) section of this manual.


c Remove water drops, snow, ice or sand


from the sunroof before opening.


c Do not place heavy objects on the sun-


roof or surrounding area.


Instruments and controls 2-33


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


Installing the sun shade 1.


Insert the 2 hooks on the front edge of sun shade into holders on the sunroof.


2. Align the 2 lock bolts on the rear edge of sun shade with the lock nuts. Turn each lock bolt clockwise to securely lock the sun shade in place.


WIC0347
Pull the handle forward to unlock s1 , then push the handle up completely to lock the sunroof closed s2 .


REMOVING/INSTALLING


WARNING


WIC0348


Do not remove or install the sun shade while driving so full attention may be given to vehicle operation. Removing the sun shade 1. Turn each lock bolt counterclockwise while


supporting the sun shade.


2. Slide the shade backward to remove it.


2-34 Instruments and controls


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


INTERIOR LIGHT


MAP LIGHTS (if so equipped)


For information regarding the interior light bulb replacement, refer to (cid:147)Bulb replacement(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.


CAUTION


Leaving the dome light switch in the ON position for extended periods of time will result in a discharged battery.


WIC0264


The interior light has a three-position switch and operates regardless of ignition switch position. c When the switch is in the ON position s1 , the interior light illuminates, regardless of door position.


c When the switch is in the center O or DOOR illuminates by


the interior


light


position, opening a door.


c When the switch is in the OFF position s2 , the interior light does not illuminate, regard- less of door position.


Type A


WIC0349


To turn the map lights on, press the switches. To turn them off, press the switches again.


CAUTION


Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.


Instruments and controls 2-35


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


ILLUMINATED ENTRY SYSTEM


The interior lights illuminate when a front, rear or the back door is opened. Once the doors are closed, these lights turn off in 30 seconds or turn off immediately when the key is turned to the ON position. BATTERY SAVER (if so equipped) If the vehicle doors are not fully closed and the interior lights remain illuminated, they eventually turn off automatically to prevent the battery from becoming discharged. Interior lights that illumi- nate when doors are opened turn off after ap- proximately 30 minutes.


Type B


WIC0350


2-36 Instruments and controls


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


3 Pre-driving checks and adjustments


Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-3
Locking with power door lock switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Child safety rear door lock. . . . . . . . . . . . . . . . . . . . . . . 3-4
Remote keyless entry system (if so equipped). . . . . . . . . 3-4
How to use remote keyless entry system . . . . . . . . . . 3-5
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Rear door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Tubular roof rack with gear basket . . . . . . . . . . . . . . . . . . 3-10


Tubular step rail (if so equipped) . . . . . . . . . . . . . . . . . . . 3-13
Fuel filler lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Fuel filler cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Tilt operation (if so equipped) . . . . . . . . . . . . . . . . . . . 3-15
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Vanity mirror (if so equipped). . . . . . . . . . . . . . . . . . . . 3-15
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
Inside mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Outside mirror remote control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/18/03—cathy X


KEYS


DOORS


WPD0152


1. 2.


Key Key plate


A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have 1 to duplicate from. If you still have a key, this key can be duplicated by a NISSAN dealer or locksmith.


3-2 Pre-driving checks and adjustments


WARNING


c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.


c Before opening any door, always look


for and avoid oncoming traffic.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.


WPD0153


Driver(cid:146)s side


LOCKING WITH KEY Manual To lock either the driver or passenger side door, turn the key toward the front of the vehicle s1 . To unlock, turn it toward the rear s2 .


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


WPD0154


WPD0155


WPD0156


Driver(cid:146)s side


Power (if so equipped) Turning the key toward the front s1 of the vehicle locks all doors. Turning the key 1 time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again s4 within 5 seconds un- locks all doors.


Inside lock


LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock knob to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .


Driver(cid:146)s side


LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) To lock all the doors without a key, push the door lock switch (driver or front passenger side), to the lock position s1 , then close the door. When locking the door this way, be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver or front passenger side) to the unlock position s2 .


Pre-driving checks and adjustments 3-3


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


When the power door lock switch (driver or pas- senger side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and then unlock automatically.


3-4 Pre-driving checks and adjustments


REMOTE KEYLESS ENTRY SYSTEM (if so equipped)


It is possible to lock/unlock all doors, turn the interior light on, and activate the panic alarm by using the keyfob from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a distance of approxi- mately 33 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle. As many as 4 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.


CAUTION


Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against


another object.


c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).


APD1078
CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


WPD0157


HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all doors 4. Push the


button on the keyfob. All the doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.


c When the


button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a re- minder that the doors are already locked. The horn may or may not beep once. Refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section for details.


c If a door is open and you push the


button, the doors will lock but the horn will not beep and the hazard lights will not flash.


WPD0158


button on the keyfob once.


Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The interior lights illuminate for 30 seconds when the interior light switch is in O or DOOR position.


button on the keyfob again with 5


Push the seconds. c All doors unlock.


Pre-driving checks and adjustments 3-5


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the OFF position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 5 minutes unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and


the key is turned from OFF to ON.


3-6 Pre-driving checks and adjustments


WPD0159


WIC0325


Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for 30
seconds. The panic alarm stops when: c it has run for 30 seconds, or c the


button is pushed on


or


the keyfob.


buttons for at least 2 seconds.


Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. To deactivate: Press and hold the and The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated.


buttons for at least 2 seconds


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered.


BATTERY REPLACEMENT Replace the battery in the keyfob as follows: s1 Open the lid using a coin. s2 Remove the battery.


s3


WPD0160
Install a new battery with the (cid:147)+(cid:148) facing down.


Recommended battery: Toshiba CR2025 or equivalent. s4 Close the lid securely.


Pre-driving checks and adjustments 3-7


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


5. Press the


button, then the


button two or three times to check the key- fob operation.


If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.


c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.


FCC Notice: Changes or modifications not expressly ap- proved by the manufacturer for compliance could void the user(cid:146)s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device. 3-8 Pre-driving checks and adjustments


HOOD


WPD0179


3. Remove the support rod from the clamp. 4.


Insert the support rod sC into the slot in the front edge of the hood.


5. When closing the hood, return the support rod to its original position, lower the hood to approximately 12 inches above the latch and release it. This allows proper engagement of the hood latch.


WARNING


c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.


c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.


1. Pull the hood lock release handle sA located below the driver side instrument panel; the hood springs up slightly.


2. Lift the lever sB at the front of the hood with


your fingertips and raise the hood.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


REAR DOOR


WPD0161


c Do not drive with the back door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See (cid:147)Exhaust gas(cid:148) in the (cid:147)Starting and driv- ing(cid:148) section of this manual.


To unlock the back door, turn the key clockwise s1 . To open the back door, lift up on the door handle s2 and lift the door up. To close, lower and push the door down securely. To lock the back door, turn the key counterclockwise s3 .


WARNING


c Always be sure the back door has been closed securely to prevent it from open- ing while driving.


Pre-driving checks and adjustments 3-9


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


TUBULAR ROOF RACK WITH GEAR BASKET


and GAWR, refer to the (cid:147)Technical and con- sumer information(cid:148) section of this manual.


WARNING


Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, un- secured cargo could cause personal injury.


CAUTION


Use care when placing or removing items from the tubular roof rack or gear basket. If you cannot comfortably lift the items onto the tubular roof rack or gear basket from the ground, use a ladder or stool.


1. 2. 3.


Adjustable cross-bar Tubular roof rack Removable gear basket


Always evenly distribute the cargo on the tubular roof rack. The maximum total load is 125 lb (57 kg) evenly distributed, including gear 3-10 Pre-driving checks and adjustments


WPD0162
basket. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Ratings (GAWR front and rear). The GVWR and GAWR are located on the Safety Compliance Certifica- tion Label (located on the driver(cid:146)s side door jamb pillar). For more information regarding GVWR


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


WPD0163


Jack rod


Tubular roof rack torxdriver


1. 2. Wheel nut wrench 3. Getting the tubular roof rack torxdriver 1. Open the back door. 2. Roll back the cargo area carpet. 3. Remove the roof rack torxdriver.


Tubular roof rack crossbar adjustment The front and rear crossbars can be adjusted forward, backward, or be removed. Use the torxdriver located in the tool kit to loosen both crossbar adjusting screws.


AIC1146


To adjust:


a. Loosen the adjusting screws with the


torxdriver by turning counterclockwise.


Pre-driving checks and adjustments 3-11


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


b. When the clamp is loosened, move the cross- bars so the cargo can be positioned between the crossbars.


c. Tighten the crossbar adjusting screws with


the torxdriver by turning clockwise.


d. Secure the cargo with rope. e. Always check the tightness of the crossbar


adjusting screws.


To remove: a. Loosen the adjusting screws with the


torxdriver by turning counterclockwise.


b. Rotate the clamps. c. Remove the crossbars. d. Reverse to install. e. Always check the tightness of the crossbar


adjusting screws.


If you hear wind noise coming from the roof rack while driving, adjust the roof rack crossbars to the most rearward position.


3-12 Pre-driving checks and adjustments


To remove the gear basket: a. Unscrew the 4 hold down bolts by turning


them counterclockwise.


b. Lift up the rear of the basket. c. Lift out the gear basket by moving it toward


the rear of the vehicle.


APD1092
The roof rack is equipped with a removable gear basket. The maximum gear basket load is 30
lb (13.6 kg) evenly distributed.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


TUBULAR STEP RAIL (if so equipped)


FUEL FILLER LID


Tubular step rail Front passenger step Rear passenger step


1. 2. 3. The tubular step rail has a front and rear step for assisting passengers getting into and out of the vehicle.


WPD0164


WPD0165


FUEL FILLER CAP The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.


WARNING


c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.


Pre-driving checks and adjustments 3-13


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


(cid:150) Always place the container on the


ground when filling.


(cid:150) Do not use electronic devices when


filling.


(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.


(cid:150) Use only approved portable fuel con-


tainers for flammable liquid.


CAUTION


c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.


c Fuel may be under pressure. Turn the cap a third turn, and wait for any (cid:147)hiss- ing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing per- sonal injury. Then remove the cap.


c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.


c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to


attempt to start your vehicle.


c Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers:


3-14 Pre-driving checks and adjustments


c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap mal- properly may cause the function indicator lamp (MIL) to illumi- nate. If the lamp illuminates be- cause the fuel filler cap is loose or missing, tighten or install the cap and to continue vehicle. The lamp should turn off after a


drive


the


lamp few driving trips. If the does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. c For additional


information, see the (cid:147)Malfunction indicator lamp (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


STEERING WHEEL


SUN VISORS


WPD0166
Put the fuel filler cap in the cap holder while refueling.


WPD0167


WPD0168


VANITY MIRROR (if so equipped) A vanity mirror is located on the rear side of the passenger sun visor.


TILT OPERATION (if so equipped) Pull the lock lever down and adjust the steering wheel up or down to the desired position. Push the lock lever up firmly to lock the steering wheel in place.


WARNING


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


Pre-driving checks and adjustments 3-15


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


MIRRORS


WPD0126


WPD0169


WPD0170


INSIDE MIRROR The night position s1 reduces glare from the headlights of vehicles behind you at night. Use the day position s2 when driving in daylight hours.


WARNING


Use the night position only when neces- sary, because it reduces rear view clarity.


Type A OUTSIDE MIRRORS The outside mirrors can be moved in any direc- tion for a better rear view. Type A: Adjust to the desired position by moving the entire mirror assembly. Type B: Adjust to the desired position by press- ing directly on the mirror surface.


Type B


3-16 Pre-driving checks and adjustments


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


WARNING


Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.


WPD0056


WPD0143


Foldable outside mirrors Push the mirrors backward to fold them.


OUTSIDE MIRROR REMOTE CONTROL (if so equipped) The outside mirror remote control only operates when the ignition switch is in the ACC or ON position.


Rotate the control lever to select the right or left mirror. Adjust the mirror to the desired position by moving the control lever.


Pre-driving checks and adjustments 3-17


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


MEMO


3-18 Pre-driving checks and adjustments


4 Heater, air conditioner and audio systems


Ventilators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . . 4-2
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Air conditioner operation . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10


Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-11
FM-AM radio with compact disc (CD) player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
FM-AM radio with compact disc (CD) changer (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-16
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


VENTILATORS


Adjust air flow direction for the driver(cid:146)s side, center, and passenger side ventilators by moving the ventilator slide and/or ventilator assemblies.


WHA0223


HEATER AND AIR CONDITIONER (manual)


WARNING


c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children, impaired adults, or pets alone in your vehicle. They could accidentally injure themselves or oth- ers through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.


c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.


c Positioning of the heater and/or air conditioner controls should not be done while driving so full attention may be given to vehicle operation.


4-2 Heater, air conditioner and audio systems


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


WHA0235


1. 2. 3. 4. 5. 6.


Fan control dial Temperature control dial Rear window defroster switch Air flow control dial Air conditioner button Air recirculation button


CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.


Air flow control dial The air flow control dial allows you to select the air flow outlets.


(cid:151) Air flows from center and side


ventilators.


(cid:151) Air flows from center and side


ventilators and the front and rear floor outlets.


(cid:151) Air flows mainly from the front and


rear floor outlets.


(cid:151) Air flows from defroster outlets


and the front and rear floor outlets.


(cid:151) Air flows mainly from defroster


outlets.


The air flow control dial also has intermediate positions which allow the air flow to be distrib- uted between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air.


Air recirculation button


NOTE:


The air recirculation feature is available only on those vehicles equipped with air conditioning.


ON position (Indicator light on): Interior air is recirculated inside the vehicle. Push the c driving on a dusty road. c to prevent traffic fumes from entering pas-


button to the on position when:


senger compartment.


c for maximum cooling when using the air con-


ditioner.


OFF position (Indicator light off): Outside air is drawn into the passenger compart- ment and distributed through the selected outlet. Use the off position for normal heater or air con- ditioner operation.


Air conditioner button


The button is provided only on vehicles equipped with an air conditioner. Start the engine, turn the fan control dial to the desired (1 to 4) position and push the button to turn on the air conditioner. The indicator Heater, air conditioner and audio systems 4-3


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


button again.


light comes on when the air conditioner is oper- ating. To turn off the air conditioner, push the The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch For more information about the rear window de- froster switch, see (cid:147)Rear window defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets.


1. Push the


button to the off position for


normal heating.


2. Turn the air flow control dial to the


position.


3. Turn the fan control dial to the desired posi-


tion.


4. Turn the temperature control dial to the de- sired position between the middle and the hot position.


Ventilation This mode directs outside air to the side and center ventilators.


1. Push the


button to the off position.


2. Turn the air flow control dial to the


position.


3. Turn the fan control dial to the desired posi-


tion.


4. Turn the temperature control dial to the de-


sired position.


Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows.


1. Turn the air flow control dial to the


position.


2. Turn the fan control dial to the desired posi-


tion.


3. Turn the temperature control dial to the de- sired position between the middle and the hot position.


4-4 Heater, air conditioner and audio systems


c To quickly remove ice or fog from the win- dows, turn the fan control dial to 4 and the temperature control lever to the full HOT position. c When the


position is selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36 - 37(cid:176)F (2 - 3(cid:176)C). The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.


Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets. 1. Push the


button (if so equipped) to


the off position.


2. Turn the air flow control dial to the


position.


3. Turn the fan control dial to the desired posi-


tion.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


4. Turn the temperature control dial to the de-


sired position.


Heating and defogging This mode heats the interior and defogs the wind- shield.


1. Turn the air flow control dial to the


position.


2. Turn the fan control dial to the desired posi-


tion.


3. Turn the temperature control dial to the de- sired position between the middle and the hot position.


c When the


position is selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36 - 37(cid:176)F (2 - 3(cid:176)C). The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position. This position other than the dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.


Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation. AIR CONDITIONER OPERATION Start the engine, turn the fan control dial to the desired (1 to 4) position, and push in the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.


1. Push the


button to the off position.


2. Turn the air flow control dial to the


position.


3. Turn the fan control dial to the desired posi-


c For quick cooling when the outside tem- button to perature is high, push the the on position (indicator light on). Be sure to return the to the off position for normal cooling.


Dehumidified heating This mode is used to heat and dehumidify the air.


1. Push the


button to the off position.


2. Turn the air flow control dial to the


position.


3. Turn the fan control dial to the desired posi-


tion.


4. Push the comes on.


button. The indicator light


5. Turn the temperature control dial to the de-


sired position.


Dehumidified defogging This mode is used to defog the windows and dehumidify the air.


tion.


4. Push the comes on.


button. The indicator light


1. Turn the air flow control dial to the


position.


5. Turn the temperature control dial to the de-


sired position.


2. Turn the fan control dial to the desired posi-


tion.


Heater, air conditioner and audio systems 4-5


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


at least once a month. This helps pre- vent damage to the system due to lack of lubrication.


c If


the engine coolant


temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.


AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recirculation button should always be in the OFF posi- tion for heating and defrosting.


3. Push the comes on.


button. The indicator light


When the or positions in between are selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36 - 37(cid:176)F (2 - 3(cid:176)C). The air conditioning system will continue to operate until the fan control dial is turned to OFF or the vehicle is shut off, even if the air flow control dial is turned to a position other than the position. This dehumidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. 4. Turn the temperature control dial to the de-


sired position. Operating tips c Keep the windows and sunroof


(if so equipped) closed while the air conditioner is in operation.


c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.


c The air conditioning system should be operated for approximately 10 minutes


4-6 Heater, air conditioner and audio systems


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


WHA0241


WHA0242


Heater, air conditioner and audio systems 4-7


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


4-8 Heater, air conditioner and audio systems


WHA0243


WHA0244


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


SERVICING AIR CONDITIONER


The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and lubricant recommendations(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.


WARNING


The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.


WHA0245


Heater, air conditioner and audio systems 4-9


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 03/17/03—cathy X


AUDIO SYSTEM


RADIO Turn the ignition key to the ACC or ON position and press the power on switch to turn the radio on. If you listen to the radio with the engine not running, the key should be turned to the ACC position.


Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.


However there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area, and do not indicate any malfunction in your NISSAN radio system.


Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 - 30
miles (40 - 48 km), with monaural (single chan- nel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.


Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.


Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter) static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response.


4-10 Heater, air conditioner and audio systems


Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


c Do not use the following CDs as they may cause the CD player to malfunc- tion: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or


have abnormal edges


disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.


c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot func- tion when the compartment tempera- ture is extremely high. Decrease the temperature before use.


c Do not expose the CD to direct sun-


light.


c CDs that are of poor quality, dirty, scratched, covered with fingerprints, or that have pin holes may not work prop- erly.


c The following CDs may not work prop-


erly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW)


Heater, air conditioner and audio systems 4-11


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


LHA0099
AUDIO OPERATION PRECAUTIONS Compact disc (CD) player c Only use high quality 4.7 inches (12 cm) round discs that have the (cid:147)COMPACT


PRESET ABC button Display


1. 2. 3. CD button 4. CD eject button 5. CD insert slot 6. MENU button AUDIO button 7. Station select buttons 8. 9. SEEK/TRACK button 10. PWR/VOL control knob 11. BAND select button FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) PWR/VOL control knob Turn the ignition key to the ACC or ON position, then push the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume.


4-12 Heater, air conditioner and audio systems


LHA0117


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


for BAL (balance). Once the audio level is set the display will return back to radio or CD display mode after 7 seconds or the AUDIO button can be pressed again within 7 seconds to set the next audio level. Pressing the AUDIO button a fifth time will return the display back to radio or CD display mode.


Fader adjusts the sound level between the front and rear speakers, balance adjusts the sound level between the right and left speakers. Clock set


1. Press and hold the MENU button until


it


beeps (longer than 2 seconds).


2. The


hours will SEEK/TRACK ( hours.


start or


flashing. Press the ) to adjust


3. Press the MENU button until the radio beeps


to switch to the minute adjustment.


LHA0118
Adjusting tone quality and speaker balance


SEEK/TRACK ( utes.


or


4. The minutes will start


flashing. Press ) to adjust the min-


FM-AM radio operation


FM-AM band select


Push the reception.


button to change from AM to FM


The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.


SEEK/manual/SCAN tuning


When the button is pushed while the radio is playing, tuning mode is cycled between: SEEK tuning ! manual tuning ! SCAN mode (cid:147)TUNE(cid:148) and (cid:147)SCAN(cid:148) are shown in the display for each mode. No icon is displayed for SEEK mode.


WARNING


The radio should not be tuned while driv- ing so full attention may be given to ve- hicle operation.


To adjust the audio levels for bass, treble, fader, and balance, push the AUDIO button and adjust the level with the SEEK/TRACK button. Press the AUDIO button once for BAS (bass), twice for TRE (treble), 3 times for FAD (fader) and 4 times


5. Press the MENU button again to exit the


clock set mode.


The display will return to the regular clock display after 7 seconds, or you may press the MENU button again to return to the regular clock display.


SEEK tuning Push the SEEK/TRACK tuning button ( or ) for less than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which button is Heater, air conditioner and audio systems 4-13


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


and


If using the


pressed, and stops at the next broadcasting sta- button, once the highest tion. broadcasting station is reached, the radio contin- ues in the SEEK mode at the lowest broadcasting station. If using the button, once the lowest broadcasting station is reached, the radio contin- ues in the SEEK mode at the highest broadcast- ing station. Manual tuning Use the buttons for manual tuning. To move quickly through the channels, hold either of the tuning buttons down. SCAN tuning Push and hold the SEEK/TRACK tuning button SCAN illuminates in the display window, and the radio station blinks. SCAN tuning begins from low to high frequencies or high to low frequen- cies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for 5 seconds. When scanning, SCAN is solid and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the sta- tion display is solid. Pushing the button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station.


) for more than 1.5 seconds.


or


Press the PRESET ABC button to change be- tween the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active. To store a radio station in a preset: 1. Select the desired preset by pressing PRE-


SET ABC.


2. Tune to the desired station. 3. Press the desired station select button for more than 3 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.


4. When the indicator illuminates in the display and the sound resumes, memorizing is com- plete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations.


LHA0119


Station memory operations


Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM and FM stations.


4-14 Heater, air conditioner and audio systems


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


Compact disc (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is auto- matically pulled into the slot and starts to play.


If the radio is already operating, it automatically turns off and the compact disc begins to play.


CAUTION


Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.


CD button


When the CD button is pushed with a compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play.


Track up/down, FF/REV (rewind) buttons


Track up/down


When the button is pushed and released while the compact disc is playing, the selection following the present one starts to play from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the CD advances 1 additional selection. The number appears in the display window.


(When the last selection on the compact disc is skipped, the first selection is played.)


button is pushed the next selection will be


button is pushed and released, the When the selection being played returns to the beginning. Push the button several times to skip back several selections. Each time the button is pushed, the CD moves back 1 selection. If the play pattern is in MIX mode when the or chosen at random. FF (Fast Forward)/REV (Reverse) When the button is pushed and held while the compact disc is playing, the compact disc plays at an increased speed while fast for- warding or rewinding. When the button is re- leased, the compact disc returns to normal play speed.


or


Blank (no symbol): All selections are played repeatedly in sequence. When a new compact disc is inserted, the play pattern automatically changes to ALL.


CD EJECT button


button is pushed with a com-


When the pact disc loaded, the compact disc ejects. When the button is pushed while the com- pact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not re- moved within 10 seconds, it is pulled back into the slot.


DISC indicator light


This light is loaded into the player.


comes on when a compact disc


MENU


When the button is pushed while the com- pact disc is playing, the play pattern changes as follows: RPT: The current selection is repeated. MIX: Selections are played at random, not fol- lowing the sequence on the compact disc. The same program may be repeated twice. If the button is pushed in the MIX mode, selections will be chosen at random.


Heater, air conditioner and audio systems 4-15


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


1. Disc loading button 2. SEEK/TRACK button 3. CD select button 4. Band select buttons 5. CD insert slot 6. CD eject button 7. Radio manual tuning buttons 8. RPT MIX/PTY button 9. CLOCK button 10. AUDIO button 11. TRAVEL PRESET button 12. Station select buttons 13. RDS button 14. SCAN button 15. PRESET SCAN button 16. ON•OFF/VOL control knob 17. PRESET ABC button


FM-AM RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) PWR/VOL control knob


Turn the ignition key to the ACC or ON position, then push the PWR/VOL control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio


WHA0134


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


4-16 Heater, air conditioner and audio systems


or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the PWR/VOL control knob again turns the system off. Turn the PWR/VOL control knob to the right to increase volume or to the left to decrease volume.


Heater, air conditioner and audio systems 4-17


WHA0065


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/21/03—tbrooks X


Adjusting tone quality and speaker balance


5. Press the CLOCK button again to exit the


or


or


Press the AUDIO button to enter the audio adjust mode: Bass!Mid!Treb!Fade!Bal Press the TUNE/FF-REV ( ) or SEEK/TRACK ( ) to adjust to the de- sired levels. The display will return to the regular radio display after 7 seconds, or you may press the AUDIO button again to return to the regular radio display. Clock operation Pressing the CLOCK button displays the clock with the radio on or off. Press the CLOCK button again to turn off the clock display. Clock set 1. Press and hold the CLOCK button until it


beeps (>2 seconds).


2. The


hours will


TUNE/FF-REV SEEK/TRACK ( hours.


start


or


flashing. Press or the


or ) to adjust


3. Press the CLOCK button to switch to the


minute adjustment.


4. Press TUNE/FF-REV (


SEEK/TRACK ( utes.


or


or


) or ) to adjust the min-


clock set mode.


The display will return to the regular clock display after 7 seconds, or you may press the CLOCK button again to return to the regular clock display. FM-AM radio operation FM-AM band select Push the AM or the FM button to change from AM to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.


TUNE/FF(cid:151)REV


WARNING


The radio should not be tuned while driv- ing so full attention may be given to ve- hicle operation.


and


Use the buttons for manual tuning. To move quickly through the channels, hold the tuning buttons down.


SEEK tuning


Push SEEK/TRACK tuning button ( ). SEEK tuning begins from low to high frequencies


or


or high to low frequencies, depending on which button is pressed, and stops at the next broad- casting station. If using the up button, once the highest broadcasting station is reached, the ra- dio continues in the SEEK mode at the lowest broadcasting station. If using the down button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station. SCAN tuning Push the SCAN button. SCAN illuminates in the display window. SCAN tuning begins from low to high frequencies or high to low frequencies. SCAN tuning stops for 5 seconds at each broad- casting station that has sufficient signal strength. When scanning, SCAN blinks in the display. Pushing the SCAN button again during this 5
second period stops SCAN tuning and the radio remains tuned to that station.


4-18 Heater, air conditioner and audio systems


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/24/03—tbrooks X


3. When the indicator illuminates in the station selection button, a beep will sound indicat- ing memorization is complete. For FM sta- tions, the indicator will turn green. For AM stations, the indicator will turn amber.


4. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is canceled. In that case, reset the desired stations.


LHA0081
Station memory operation (cid:151) Travel Preset is OFF Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM, FM and FM RDS stations. Press the PRESET ABC button to change be- tween the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active.


WHA0064


To store a radio station in a preset:


1. Tune to the desired station.


2. Press the desired station select button (>2
seconds). For example, in the illustrations ch3 is to be memorized.


Heater, air conditioner and audio systems 4-19


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/24/03—tbrooks X


4.


5.


If the radio cannot find any stations, the radio displays (cid:147)NO STATION(cid:148) and mutes the au- dio. If the radio cannot fill all the presets, the remaining presets are stored with 87.9 for FM and 600 for AM.


The TUNE, SCAN, SEEK and preset memory functions are available while Travel Preset mode is on. Canceling travel preset Press the TRAVEL PRESET button (<1.5 sec- onds) to clear the Travel Preset memory. This turns off the green indicator. The radio returns to the last used preset of A, B or C in the permanent preset memory.


LHA0082


Turning ON travel preset


1. Press the TRAVEL PRESET button (<1.5
seconds). The green TRAVEL PRESET but- ton indicator turns on.


2. The radio selects the strongest stations in the area and stores them in Travel Presets A, B and C. 12 FM stations and 6 AM stations are the default settings. To change the de- fault settings, see (cid:147)Editing Travel Preset(cid:148) later in this section.


3. When finished storing radio stations, the radio tunes to the first stored preset of Travel Preset A.


4-20 Heater, air conditioner and audio systems


LHA0084


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/24/03—tbrooks X


Editing travel preset


1. Press and hold the TRAVEL PRESET button (>3 seconds) until the radio beeps to start the editing mode. The green Travel Preset indicator will flash while in TRAVEL PRESET EDIT mode.


2. The presets are transferred from Travel Pre- set memory to the permanent preset memory for A, B, and C. (cid:147)PRESETS LOADED(cid:148) is displayed.


3. The TRAVEL PRESET indicator turns off.


2. The radio displays (cid:147)TRAVEL EDIT(cid:148) for 2
seconds and then changes to (cid:147)SET A-*(cid:148) . ) to


3. Press TUNE/FF-REV (


or


select a mode.


4. Press the TRAVEL PRESET button to save


the mode.


5. Display is changed to (cid:147)SET B-*(cid:148) , repeat


steps 3 and 4.


6. Display is changed to (cid:147)SET C-*(cid:148) , repeat


step 3.


7. Press the TRAVEL PRESET button to exit


the edit mode and return to normal mode.


*: AM, FM, FM RDS, Rock, Classic Rock, Soft Rock, Top 40, Country, Jazz, Classical, Oldies, News, Sports, Talk. Storing Travel Preset stations in permanent memory 1. While in Travel Preset mode, press and hold the TRAVEL PRESET button until it beeps (>3 seconds).


LHA0085


Preset scan Pressing the PRESET SCAN button (<1.5 sec- onds) scans the permanent preset memory that is selected (A, B or C) from 1(cid:150)6 for 5 seconds. If the Travel Preset is ON, the travel preset that is selected (A, B or C) from 1(cid:150)6 is scanned for 5
seconds.


Heater, air conditioner and audio systems 4-21


Z REVIEW COPY:—2003 Xterra (xtr) Owners Manual (owners)—USA English (nna) 02/24/03—tbrooks X


stations on the FM band (not AM band) encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data.


RDS can display: c Station call sign, such as (cid:147)WHFR 98.3(cid:148). c Station name, such as (cid:147)The Groove(cid:148). c Music or programming type, such as (cid:147)Clas-


sical(cid:148), (cid:147)Country(cid:148), or (cid:147)Rock(cid:148).


c Traffic reports about delays or construction. If the station broadcasts RDS information the RDS icon is displayed. The RDS information will be displayed according to the option chosen in the RDS setup mode. (FM & RDS is the default.) Press the RDS button again to display the fre- quency for 3 seconds. The radio will then return to the normal display. If the station does not broadcast RDS information, the RDS icon will not be displayed. Setting RDS mode Press and RDS button (>3 seconds) until the display shows (cid:147)RDS SET MODE(cid:148) . This display will last 2 seconds and then change to (cid:147)TRAFFIC-OFF(cid:148) . Press TUNE/FF-REV ( or ) to toggle the RDS traffic mode from (cid:147)OFF(cid:148) to (cid:147)ON(cid:148). Press the RDS button again to set your RDS traffic mode selection.


All preset scan


LHA0086


Pressing the PRESET SCAN button (>1.5 sec- onds) scans all the permanent preset memory banks (A, B or C) from 1(cid:150)6 for 5 seconds. If the Travel Preset is ON, all the travel preset memory banks (A, B or C) from 1(cid:150)6 are scanned for 5
seconds. Canceling preset scan mode Pressing any button except CLOCK, EJECT and PTY cancels the Preset Scan mode. RDS (radio data system) RDS stands for Radio Data System, and is a data information service transmitted by some radio 4-22 Heater, air conditioner and audio systems


or


The display changes to (cid:147)SHOW(cid:148) for the second part of the RDS mode selection. Press TUNE/FF- ) to switch between the REV ( following RDS display modes: c (cid:147)FM & RDS(cid:148): the radio display will show the station(cid:146)s broadcast frequency and the sta- tion(cid:146)s name.

Loading...
x