2000 Nissan Quest Owners Manual

vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Ve- hicle Safety Standards. Once the child has grown enough so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.

WARNING

Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is mov- ing. The child could be seriously in- jured or killed in an accident or sudden stop.

PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific rec- ommendations.

Seats, restraints and supplemental air bag systems 1-41

Z X

INJURED PERSONS NISSAN recommends injured persons use seat belts, depending on the injury. Check with your doctor for specific recommenda- tions.

ARS1159

WRS0029

THREE-POINT TYPE SEAT BELT WITH RETRACTOR

WARNING

c Every person who drives or rides in this vehicle should use a seat belt at all times.

c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident

you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. c For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat properly. See “Precautions on seat belt usage” earlier in this section.

1-42 Seats, restraints and supplemental air bag systems

Z X

later in this section for

‘‘Child restraints’’ more information. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passen- ger, the locking mode should not be activated. If it is activated, it may cause uncomfortable seat belt tension.

ARS1161

ARS1162

Fastening the seat belts 1. Adjust the seat. 2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.

3. Position the lap belt portion low and

snug on the hips as shown.

4. Pull the shoulder belt portion toward the

retractor to take up extra slack.

The front seat passenger seat belt and rear three-point seat belts have a cinching mechanism for child restraint installation. It is referred to as the automatic locking mode. When the automatic locking mode is acti- vated, the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted. Refer to

Seats, restraints and supplemental air bag systems 1-43

Z X

c Grasp the shoulder belt and pull quickly forward. The retractor should lock and restrict further belt movement. the retractor does not

If lock during this check or if you have any questions about belt operation, see an authorized NISSAN dealer.

ARS1054

Unfastening the seat belts To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts. Checking seat belt operation Seat belt retractors are designed to lock seat belt movement: 1) when the seat belt is pulled quickly from

the retractor, and

2) when the vehicle slows down rapidly. To increase your confidence in the seat belts, check their operation as follows. 1-44 Seats, restraints and supplemental air bag systems

APD0831

Shoulder belt height adjustment (for front seats) The shoulder belt anchor height should be adjusted to the position best for you (See ‘‘Precautions on seat belt usage’’ earlier in this section.). To adjust, press the release button and move the shoulder belt anchor to the desired position so the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off your shoulder. Release the button to lock the shoulder belt anchor into position.

Z X

WARNING

c After adjustment, release the adjust- ment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position.

c The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the en- tire restraint system and increase the chance or severity of injury in an accident.

not be against your body. In an acci- dent you could be thrown into it and receive neck or other serious inju- ries. You could also slide under the lap belt and receive serious internal injuries.

c For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.

Fastening the seat belt 1. Adjust the seat. 2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.

ARS1083

THREE-POINT TYPE SEAT BELT WITH RETRACTOR FOR SECOND ROW BUCKET SEATS

WARNING

c Every person who drives or rides in this vehicle should use a seat belt at all times.

c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will

Seats, restraints and supplemental air bag systems 1-45

Z X

Two buckle seat belt system for the second row bench seat There is a two buckle seat belt system for the seating position of the second row bench seat next to the passenger side slid- ing door.

WARNING

c It is very important that you follow the instructions in this section before anyone rides in this seating position of the two-passenger bench seat.

c Failure to do so may result in im- proper positioning of seat belt which could lead to increased likelihood or severity of injury in a sudden stop or collision.

APD0830

3. Position the lap belt portion low on the

hips as shown.

4. Pull the shoulder belt portion toward the

retractor to take up extra slack.

1-46 Seats, restraints and supplemental air bag systems

ARS1127

The two-passenger bench seat in the sec- ond row has a seat belt system made up of two buckles and two tongues. There are two body attaching points (one upper and one lower) that attach each end of the seat belt webbing.

Z X

positioned properly and fastened to the buckle mounted in the middle of the seat. When the two buckle seat belt system is not in use, the webbing can be secured with the seat belt clip. The seat belt clip should not be used with a child seat or during seat belt usage. The seat belt clip opening should face the front of the vehicle.

ARS1126

A twisted belt may prevent the retractor from working properly. If the two buckle seat belt system is twisted, disengage the single window tongue from the auxiliary buckle on the side of the seat, remove the twist and reinstall the tongue into the auxiliary buckle until you hear a snap and feel the latch engage. Both tongues must be attached to their appropriate buckles whenever someone is riding in that seating position. If the tongue are released to allow a third row passenger to enter or exit, the tongues must be reattached.

Seats, restraints and supplemental air bag systems 1-47

Z X

WRS0051

One of the seat belt tongues has two ‘‘win- dows’’ (or holes) and the other has only one ‘‘window’’. The seat belt tongue with one window attaches to the auxiliary buckle mounted to the side of the seat. The seat belt tongue with two windows should be

When the two-passenger bench seat is re- moved from the vehicle, you must detach the single window tongue from the auxiliary buckle. When the three-passenger bench seat is moved up to the second row position, the passenger seated near the passenger side sliding door needs to use the double window tongue and the standard buckle only. Because three-passenger bench seat is wider and closer to the passenger side sliding door, the single window seat belt tongue and the auxiliary buckle are not necessary.

the

ARS1125

CAUTION

Third row passengers must be very careful when exiting because of the auxiliary seat belt. It is important to step over the seat belt guide and belt webbing to avoid tripping.

Unfastening the seat belts To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts.

1-48 Seats, restraints and supplemental air bag systems

Checking seat belt operation (Three-point type seat belt with retractor) Seat belt retractors are designed to lock seat belt movement: 1) when the seat belt is pulled quickly from

the retractor, and

2) when the vehicle slows down rapidly. To increase your confidence in the seat belts, check their operation as follows. c Grasp the shoulder belt and pull quickly forward. The retractor should lock and restrict further belt movement. the retractor does not

If lock during this check or if you have any questions about seat belt operation, see an authorized NIS- SAN dealer.

Z X

THREE-PASSENGER BENCH SEAT IN THE SECOND ROW POSITION Fastening the seat belts When the three-passenger bench seat is moved up to the second row position, the passenger seated near the passenger side sliding door needs to use the double window tongue and the standard buckle only. Because three-passenger bench seat is wider and closer to the passenger side sliding door, the single window seat belt tongue and the auxiliary buckle are not necessary. 1. Adjust the seat.

the

WRS0015

WRS0052

2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until you hear and feel the latch engage.

3. Position the passenger side shoulder belt

in the shoulder belt retainer.

Seats, restraints and supplemental air bag systems 1-49

Z X

WRS0053

WRS0015

4. Position the lap belt portion low on the

hips as shown.

5. Pull the shoulder belt portion toward the

retractor to take up extra slack.

THREE-PASSENGER BENCH SEAT Fastening the seat belts 1. Adjust the seat.

1-50 Seats, restraints and supplemental air bag systems

WARNING

c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an acci- dent you could be thrown into it and receive neck or other serious inju- ries. You could also slide under the lap belt and receive serious internal injuries.

c For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.

Third row passenger shoulder belts are located slightly behind the third row seating position. Never try to use the seat belts for the second row passen- gers which are in front of the three- passenger bench seat.

Z X

WARNING

Use of the second row three-point seat belts by third row passengers could increase the chance or severity of in- jury in a sudden stop or an accident.

2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the belt to move, and allows you some freedom of move- ment in the seat.

ARS1084

APD0162

3. Position the lap belt portion low on the

hips as shown.

4. Pull the shoulder belt portion toward the

retractor to take up extra slack.

TWO-POINT TYPE SEAT BELT WITHOUT RETRACTOR (Center of rear seat) Selecting correct set of seat belts The seat belt tongues must be fastened into the seat belt buckles as illustrated above.

WARNING

Any rear seat belt tongue will connect to any seat belt buckle; therefore, it is important to follow the illustration above. Failure to do so could increase

Seats, restraints and supplemental air bag systems 1-51

Z X

the chance and/or severity of injury in an accident.

ARS1055

ARS1238

Fastening the seat belts 1. Insert the tongue into the buckle until you

hear and feel the latch engage.

2. Tighten the seat belt by pulling the free

end of the belt away from the tongue.

1-52 Seats, restraints and supplemental air bag systems

Z X

ARS1076

ARS1057

ARS1058

3. Position the lap belt low on the hips as

shown.

4. Loosen the seat belt by holding the tongue at a right angle to the belt, then pull on the belt.

Unfastening the seat belts To unfasten the belt, press the button on the buckle. SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the front seat lap belts and fasten them, an extender is available which is compatible with the in- stalled seat belts. The extender adds ap- proximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position. See an autho-

Seats, restraints and supplemental air bag systems 1-53

Z X

c Periodically check to see that the seat belt and the metal components such as buckles, tongues, retractors, flexible wires and anchors work properly. If loose parts, deterioration, cuts or other dam- age on the webbing is found, the entire seat belt assembly should be replaced.

rized NISSAN dealer for assistance if the extender is required.

WARNING

c Only NISSAN seat belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN seat belts.

c Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.

SEAT BELT MAINTENANCE c To clean the seat belt webbings, apply a mild soap solution or any solution rec- ommended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry.

c If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoul- der belt guide with a clean, dry cloth.

1-54 Seats, restraints and supplemental air bag systems

CHILD RESTRAINTS

PRECAUTIONS ON CHILD RE- STRAINTS

WARNING

c Infants and small children should al- ways be placed in an appropriate child restraint system while riding in the vehicle. Failure to use a child restraint can result in serious injury or death.

c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe acci- dent. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.

c Never install a rear-facing child re- straint in the front seat. An inflating air bag could seriously injure or kill your child. A rear-facing child restraint must only be used in the rear seat.

c NISSAN recommends that the child restraint be installed in the rear seat. According to accident statistics, children are safer when properly re- strained in the rear seat than in a front seat.

Z X

c An improperly installed child re- straint could lead to serious injury in an accident.

c In general, child restraint systems are designed to be installed with a lap belt or the lap portion of a three- point type seat belt.

compatible with your child. Always follow all recommended procedures.

All U.S. states and some provinces or territories of Canada require that infants and small children be restrained in ap- proved child restraints at all times while the vehicle is being operated.

Child restraints for infants and children of various sizes are offered by several manu- facturers. When selecting any child re- straint, keep the following points in mind: 1) Choose only a restraint with a label cer- tifying that it complies with Federal Motor Vehicle Safety Standard 213 or Cana- dian Motor Vehicle Safety Standard 213. 2) Check the child restraint in your vehicle to be sure it is compatible with the vehi- cle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recommended practice J1819 for child seat installation.

3) If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjust- ments to be sure the child restraint is

WARNING

c Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.

c Follow all of

the child restraint manufacturer’s instructions for in- stallation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.

c If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.

c Adjustable seatbacks should be po- sitioned to fit the child restraint, but as upright as possible.

c After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.

c For a front facing child restraint, if the seat position where it is installed has a three-point type lap/shoulder belt, check to make sure the shoul- der belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint. If you must install a front facing child restraint in the front seat, see ‘‘Installation on front pas- senger seat’’ later in this section.

c When your child restraint is not in use, keep it secured with a seat belt to prevent from being thrown around in case of a sudden stop or accident.

it

Seats, restraints and supplemental air bag systems 1-55

Z X

CAUTION

Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.

WRS0054

ARS1169

INSTALLATION ON THREE- PASSENGER BENCH SEAT CENTER POSITION Front facing When you install a child restraint in a rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. Always follow the restraint manufacturer’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

1-56 Seats, restraints and supplemental air bag systems

Z X

ARS1170

ARS1171

ARS1172

3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely in place.

5. If it is not secure, try to tighten the seat belt again, or put the restraint in another seat.

6. Check to make sure the child restraint is

properly secured prior to each use.

Rear facing When you install a child restraint in a rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. Always follow the restraint manufacturer’s instructions.

Seats, restraints and supplemental air bag systems 1-57

Z X

ARS1173

ARS1174

ARS1175

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely in place.

5. If it is not secure, try to tighten the seat belt again, or put the restraint in another seat.

6. Check to make sure the child restraint is

properly secured prior to each use.

1-58 Seats, restraints and supplemental air bag systems

Z X

INSTALLATION ON SECOND AND THIRD ROW OUTBOARD POSITIONS Front facing The following instructions apply to second row bucket seats, the second row bench seat and the outboard positions of the three- passenger bench seat.

WARNING

WARNING

c The three-point belt in your vehicle is equipped with locking mode re- tractor which must be used when installing a child restraint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

if

it

When installing a child restraint in the two-passenger bench seat, is placed in the seating position next to the passenger side sliding door, be sure both the auxiliary buckle and main buckle are properly fastened. Failure to do so could increase the chance and/or severity of injury in an accident.

WRS0055

When you install a child restraint in a sec- ond row bucket seat, the second row bench seat or the outboard positions of the three- passenger bench seat follow these steps: 1. Position the child restraint on the seat. Always follow the restraint manufactur- er’s instructions.

Seats, restraints and supplemental air bag systems 1-59

Z X

ARS1177

ARS1178

ARS1179

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

1-60 Seats, restraints and supplemental air bag systems

Z X

After the child restraint is removed and the seat belt is fully retracted (for the passenger side of the two-passenger bench seat, the auxilliary buckle must also be released), the automatic locking mode (child restraint mode) is canceled. Rear facing The following instructions apply to second row bucket seats, the second row bench seat and the outboard positions of the three- passenger bench seat.

WARNING

c The three-point belt in your vehicle is equipped with a locking mode re- tractor which must be used when installing a child restraint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The seat could tip over or otherwise be unse- cured and cause injury to the child in a sudden stop or collision.

ARS1180

WARNING

if

it

When installing a child restraint in the two-passenger bench seat, is placed in the seating position next to the passenger side sliding door, be sure both the auxiliary buckle and main buckle are properly fastened. Failure to do so could increase the chance and/or severity of injury in an accident.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more seat belt out of the retractor. If you can- not pull any more belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps three through six.

Seats, restraints and supplemental air bag systems 1-61

Z X

ARS1181

ARS1182

ARS1183

When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. Always follow the restraint manufactur- er’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.

1-62 Seats, restraints and supplemental air bag systems

Z X

After the child restraint is removed and the seat belt is fully retracted (for the passenger side of the two-passenger bench seat, the auxilliary buckle must also be released), the automatic locking mode (child restraint mode) is canceled.

ARS1184

ARS1185

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more seat belt out of the retractor. If you can- not pull any more belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps three through six.

Seats, restraints and supplemental air bag systems 1-63

Z X

c The three-point belt in your vehicle is equipped with a locking mode re- tractor which must be used when installing a child restraint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

INSTALLATION ON FRONT PASSENGER SEAT

WARNING

c Never install a rear-facing child re- straint in the front passenger seat. Supplemental front air bags inflate with great force. A rear-facing child restraint could be struck by the air bag in a crash and could seriously injure or kill your child.

ARS1135

c NISSAN recommends that child re- straints be installed in the rear seat. However, if you install a forward- facing child restraint in the front pas- senger seat, move the passenger seat to the rear most position.

c A child restraint with a top tether strap should not be used in the front passenger seat.

1-64 Seats, restraints and supplemental air bag systems

Z X

ARS1163

ARS1164

ARS1165

If you must install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a forward-facing direction only. Move the seat to the rearmost position. Always follow the child restraint manufacturer’s instructions. Child restraints for infants must be used in the rear-facing direc- tion and therefore must not be used in the front seat.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.

Seats, restraints and supplemental air bag systems 1-65

Z X

After the child restraint is removed and the seat belt the automatic locking mode (child restraint mode) is can- celed.

is fully retracted,

ARS1166

ARS1167

4. Allow the seat belt to retract. Pull up on

the belt to remove any slack in the belt.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the lap belt is not locked, repeat steps three through six. 1-66 Seats, restraints and supplemental air bag systems

Z X

CHILD RESTRAINT WITH TOP TETHER STRAP

A child restraint anchored with a top tether strap can be installed on the second row bench seat, a second row bucket seat, or the three-passenger bench seat in the sec- ond or third row. The chart indicates where the tether strap must be attached and the section of that contains the this manual instructions for tethering.

Seat type

Position

Tether to

Reference

Bucket seat

Second row; center of seat

Anchor bracket on back of bucket seat

Two passenger bench seat

Second row; outboard seating positions

Two-passenger bench seat with integrated child safety seat

Second row; driver side seating position

Anchor bracket on back of second row bench seat

Anchor bracket on back of second row bench seat

Two-passenger bench seat with integrated child safety seat

Second row; passen- ger side seating posi- tion

CANNOT BE TETHERED

Three-passenger bench seat

Three-passenger bench seat

Second row; passen- ger side outboard seating position or center seating position

Anchor bracket on back of the three pas- senger bench seat

Third row; passenger side outboard or cen- ter seating position

Anchor bracket on back of the three pas- senger bench seat.

Three-passenger bench seat

Second or third row; driver side outboard seating position

CANNOT BE TETHERED

Page 1-68, Installation on second row bench or bucket seat

Page 1-68, Installation on second row bench or bucket seat

Page 1-68, Installation on second row bench or bucket seat

—

Page 1-70, Installation on three-passenger bench seat in second row

Page 1-70, Installation on three-passenger bench seat in third row

—

Seats, restraints and supplemental air bag systems 1-67

Z X

INSTALLATION ON SECOND ROW BENCH OR BUCKET SEAT A child restraint with a top tether strap may be placed on the second row bench or bucket seats. Once the child restraint is properly secured to the seat (see “Installa- tion on second and third row outboard posi- tions, Front facing” earlier in this section), follow the directions to attach the tether strap to the tether strap anchor bracket.

c The head restraint on the second row bucket seat with the integrated child seat is not adjustable, but there is an opening under the head restraint to route the tether strap through. Gently lift the head restraint and route the tether strap under the center of the head restraint through to the back side of the seat.

APD0839

To attach a tether strap to a second row bench or bucket seat: 1. Route the tether strap under the head restraint and between the head restraint supports.

1-68 Seats, restraints and supplemental air bag systems

Z X

ARS1194

ARS1193

ARS1199

2. Hook the tether strap into the slot in the anchor bracket on the second row seat (located on the lower back of the seat, in line with the head restraint).

Seats, restraints and supplemental air bag systems 1-69

Z X

follow the directions to attach the tether strap anchor brackets.

INSTALLATION ON THREE- PASSENGER BENCH SEAT IN SECOND ROW A child restraint with a top tether strap may be placed at the passenger side outboard and center positions on the three-passenger bench seat when the seat is in the second row location. Once the child restraint is prop- erly secured to the seat (see “Installation on second and third row outboard positions, Front facing” earlier in this section), follow the directions explained in ‘‘Installation on three passenger bench seat in third row’’ later in this section. INSTALLATION ON THREE- PASSENGER BENCH SEAT IN THIRD ROW A child restraint with a top tether strap may be placed at the passenger side outboard and three- passenger bench seat when the seat is in the third row location. Once the child re- straint is properly secured to the seat (see “Installation on second and third row out- board positions, Front facing” or “Installation on three-passenger bench seat center posi- tion, Front facing” earlier in this section),

positions

center

the

on

ARS1192

3. Tighten the tether strap to remove any

slack.

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

5. Check to make sure the child restraint is properly secured prior to each use. If not secure, repeat steps two through four.

1-70 Seats, restraints and supplemental air bag systems

Z X

WRS0022

LRS0023

WRS0024

To attach a tether strap to a third row bench seat: 1. For the passenger side outboard seating position, route the tether strap under the head restraint and between the head restraint supports. For the center seating position, route the tether strap over the seatback.

2. Hook the tether strap into the slot in the is located on the

that

anchor bracket lower back of the seat.

3. Tighten the tether strap to remove any

slack.

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

5. Check to make sure the child restraint is properly secured prior to each use. If it is not secure, repeat steps two through four.

Seats, restraints and supplemental air bag systems 1-71

Z X

INTEGRATED CHILD SAFETY SEATS (if so equipped)

WARNING

c Failure to follow the instructions for the use of these integrated child safety seats can result in your child striking the vehicle’s interior during a sudden stop or crash, causing the injury or death of your child.

c Improper use of a child restraint can increase the risk or severity of injury for both the child and other occu- pants of the vehicle.

these integrated child safety In addition, seats must only be used by children who meet the following requirements: c AGE:

At least one year old

c SEATED HEIGHT:

Top of child’s shoulders must be below the shoulder harness openings of the integrated child seat.

Children less than one year old should be restrained in an appropriate separate child restraint. Children whose shoulders are above the shoulder harness openings of integrated child seat should also be re- strained in an appropriate separate child restraint or in the appropriate vehicle seat belt system. Refer to ‘‘Child Restraints’’ and ‘‘Precautions On Seat Belt Usage’’ in this section for important child safety information.

All U.S. states and Canadian provinces require that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper- ated. The optional second row bench seat con- tains two integrated child safety seats. These seats are designed for use only by children who weigh between 22 and 60
pounds (10-27 kg) and whose height is 45
inches (1145 mm) or less and who are capable of sitting upright alone. 1-72 Seats, restraints and supplemental air bag systems

Z X

c Before placing the child in the inte- grated child safety seat, confirm that the bench seatback is securely locked and the seatback release le- ver is in full down position.

c Always make sure the integrated child safety seat belts are properly positioned on your child. The child should sit straight up and back against the bench seat. The shoulder harnesses should be centered over the shoulders and fastened with the chest clip. The belt buckle should be between the legs and latched to the shoulder belt tongue. Snugly adjust the belts around your child. Failure to properly position the child can increase the risk or severity of injury to the child in an accident.

Using the Integrated Child Safety Seats

WARNING:

c Never use the vehicle seat belts to restrain a child in an integrated child

safety seat. Use only the shoulder- harness and belt buckle which is part of the integrated child safety seat. Never use the integrated child safety seat as a booster cushion with the vehicle seat belts.

Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.

ARS1215

CAUTION

Seats, restraints and supplemental air bag systems 1-73

Z X

Securing the child Before using the integrated child safety seats, carefully read the shoulder har- ness, seatback release, and integrated child safety seat cushion labels. The following steps apply to both the left and right integrated child safety seats. 1. Be sure your child meets all of the re- quired age, weight and height require- ments for the safe use of the integrated child safety seat.

2. Be sure the second row bench seat is securely latched to the floor of the ve- hicle. Refer to ‘‘Flexible seating’’ in this section for proper seat installation proce- dures.

3. Be sure the second row bench seatback is locked by grasping it and trying to rock it back and forth. Also, check that the seatback release lever is in the full down position.

4. Pull the cushion release strap and lower the intregrated child safety seat cushion completely.

NOTE: The head restraints on the pas- senger bench seat equipped with the integrated child safety seats, are not adjustable or removable.

ARS1201

1-74 Seats, restraints and supplemental air bag systems

Z X

APD0814

APD0815

APD0816

5. If connected, separate the two halves of the shoulder harness from the belt buckle. Also if connected, disconnect the chest clip and lay the shoulder harness halves aside.

6. Place the child on the integrated child safety seat. Place the belt buckle be- tween the child’s legs.

Seats, restraints and supplemental air bag systems 1-75

Z X

APD0817

APD0818

APD0819

7. Place the left shoulder harness over the child’s left shoulder. Insert the left shoulder harness tongue into the left side of the belt buckle. Confirm that the left shoulder har- ness tongue indicator is green. The shoul- der harness tongues only fit into the proper sides of the belt buckle.

8. Place the right shoulder harness over the child’s right shoulder. Insert the right shoul- der harness tongue into the right side of the belt buckle. Confirm that the right shoulder harness tongue indicator is green. The shoulder harness tongues only fit into the proper sides of the belt buckle.

9. Fasten the two halves of the chest clip and confirm that the chest clip indicator is green. Adjust the chest clip (slightly lower than the child’s shoulders) so it comfort- ably holds the shoulder harness in positi- ton on the child’s shoulders.

WARNING

c Shoulder harness tongues and chest clips are equipped with visual indica- tors to confirm proper and secure latching. For the safety of the child and occupants of the vehicle, all indi-

1-76 Seats, restraints and supplemental air bag systems

cators must show green before oper- ating the vehicle.

c If the shoulder harness is unfas- tened or not fastened properly, the child could be seriously injured.

10. Grasp the right shoulder harness above the chest clip and pull until the harness fully extends and a click is heard. At this time, the harness retractor is in the automatic locking mode (child restraint mode). With the child sitting properly (straight up and back) in the integrated child safety seat, allow the right shoul-

Z X

der harness to retract over the right shoulder and securely restrain the child. A clicking sound is heard as the har- ness retracts, indicating that the retrac- tor is in the automatic locking mode. Be sure the left shoulder harness is also properly positioned over the child’s left shoulder.

the shoulder harness out of

11. Check that the shoulder harness is in the automatic locking mode by trying to pull the retractor. If you cannot pull any of the shoulder harness webbing out of the retractor, the shoulder harness is in the automatic locking mode. If the shoulder harness is not locked, repeat step 10. If, after repeated attempts, the integrated child safety seat shoulder harness can- not be placed in the automatic locking mode, do not use the integrated child safety seat and have it inspected by an authorized NISSAN dealer.

To cancel the automatic locking mode, un- buckle the chest clip and both shoulder harness tongues. Allow the shoulder har- nesses to retract completely. The automatic locking mode is now canceled and the

shoulder harness retractor is in the emer- gency locking mode.

ness tongues from the belt buckle by pressing the red belt buckle button.

WARNING

The automatic locking mode (child re- straint mode) must be reactivated each time you place a child in the integrated child safety seats.

In addition to the automatic locking retrac- tors, the integrated child safety seat shoul- der harnesses are equipped with emer- gency locking retractors. The automatic locking mode is best to use, especially for children who need help staying properly positioned in the seat and its harnesses (for example, children who are younger and smaller), because the belts are always locked. In the emergency locking mode, the shoulder belts only lock in a sudden stop or accident, allowing a child more freedom of movement. Use the emergency locking mode only if you judge your child able to remain properly positioned in the integrated child safety seat. Removing the child 1. Release the chest clip. 2. Release the left and right shoulder har-

3. Move the left and right shoulder har- nesses aside and assist the child from the integrated child safety seat.

Storing the Integrated Child Safety Seat 1. Be sure the shoulder harnesses are fully retracted and resting inside the inte- grated child safety seat recess. It is not necessary to reconnect the shoulder har- nesses and belt buckle prior to storing the integrated child safety seat.

2. While holding onto, but not pulling, the cushion release strap, rotate the cushion upward until it fits flush with the second row seat back cushion and locks into position.

3. Be sure the integrated child safety seat is locked in the stowed position by grasping the safety seat cushion and attempting to lower it without pulling the cushion re- lease strap. If the integrated child safety seat is not locked in the stowed position, repeat steps one through three.

Seats, restraints and supplemental air bag systems 1-77

Z X

c Periodically inspect the belt and metal components of the integrated child safety seats, such as the buckles, tongues, shoulder harness webbings, and latching indicators. Periodically check the func- tion of the integrated child safety seat shoulder harness retractor functions. If loose parts, deterioration, cuts, frays, malfunctions or other damage to the belt webbings or metal parts are found, see an authorized NISSAN dealer for repairs.

Inspection after an accident If your vehicle was involved in an accident, before using the integrated child safety seats, all related components should be inspected for damage by an authorized NIS- SAN dealer. Damage to the integrated child safety seat or related components must be repaired.

Integrated Child Safety Seat main- tenance c To clean the shoulder harnesses and belt buckle webbing, apply a mild soap solu- tion or any solution recommended for cleaning upholstery or carpets. Then brush the webbing, wipe it with a cloth and allow it to dry in the shade. Do not allow the shoulder harnesses to retract until they are completely dry.

c The integrated child safety seats cloth removable pads may be cleaned with mild soap and water. The cloth remov- able pads are attached to the seats with fastener strips, and may be easily re- moved. The pads are machine washable. Fo best results, machine wash in cold water in the gentle cycle. Tumble dry on low heat. Do not use chlorine bleach, and do not dry clean.

CAUTION

Failure to follow the washing instruc- tions provided on the cloth removable pads may result in premature wear or damage.

1-78 Seats, restraints and supplemental air bag systems

Z X

MEMO

Seats, restraints and supplemental air bag systems 1-79

Z X

2 Instruments and controls

Meters and gauges ................................................2-3
Speedometer and odometer ..................................2-4
Tachometer ............................................................2-4
Engine coolant temperature gauge........................2-4
Fuel gauge .............................................................2-5
Warning/indicator lights and chimes ......................2-6
Checking bulbs.......................................................2-6
Warning lights.........................................................2-6
Indicator lights ........................................................2-8
Chimes .................................................................2-10
Theft warning (if so equipped) .............................2-10
Windshield wiper and washer switch...................2-12
Rear window wiper and washer switches............2-13
Rear window defogger switch..............................2-14
Headlight control switch .......................................2-14
Autolamp switch (if so equipped).........................2-15
Turn signal switch .............................................2-16
Cornering light......................................................2-17
Hazard warning flasher switch.............................2-17
Horn......................................................................2-18
Rear power socket ...............................................2-18
Cigarette lighter and ashtray (accessory)............2-19

Storage.................................................................2-20
Map pockets.........................................................2-20
Conversation mirror..............................................2-20
Cup holders..........................................................2-21
Glove box .............................................................2-22
Front seat convenience net (if so equipped) .......2-23
Cargo net..............................................................2-24
Parcel shelf (if so equipped) ................................2-25
Luggage rack .......................................................2-27
Windows...............................................................2-27
Power windows ....................................................2-27
Power vent windows (if so equipped)..................2-29
Manual vent windows...........................................2-29
Sunroof (if so equipped).......................................2-30
Interior lights.........................................................2-31
Luggage ...............................................................2-31
Personal reading light ..........................................2-31
Map lights.............................................................2-32
Illuminated entry system ......................................2-32
Integrated HomeLinkT universal transceiver (if so equipped) ....................................................2-32
Programming HomeLinkT.....................................2-33

Z X

Programming HomeLinkT for Canadian customers.............................................................2-34
Operating the integrated HomeLinkT universal transceiver............................................................2-34
Programming problem diagnosis .........................2-34
Clearing the programmed information .................2-35

Rolling code programming ...................................2-35
If your vehicle is ever stolen ................................2-36
Storage compartment for garage door transmitter (if so equipped) ..................................2-36

Z X

2-2 Instruments and controls

WIC0017

Z X

METERS AND GAUGES

AIC1094

Instruments and controls 2-3

Z X

SPEEDOMETER AND ODOMETER

TACHOMETER

ENGINE COOLANT TEMPERATURE GAUGE

AIC0003

AIC0110

AIC0004

Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). Odometer The odometer records the total distance the vehicle has been driven. Trip odometer The trip odometer records the distance of individual trips. Before each trip, set the trip odometer to zero by pushing the RESET button. 2-4 Instruments and controls

The tachometer indicates engine speed in revolutions per minute (RPM).

CAUTION

When engine speed approaches the red zone, shift to a higher gear. Oper- ating the engine in the red zone may cause serious engine damage.

This gauge indicates the engine coolant temperature. The engine coolant tempera- ture varies with the outside air temperature and driving conditions.

CAUTION

If the gauge indicates engine coolant temperature above the normal range, stop the vehicle as soon as safely pos- sible. If the engine is overheated, con- tinued operation of the vehicle may seriously damage the engine. See the ‘‘In case of emergency’’ section for immediate action required.

Z X

CAUTION

malfunction indicator

c If the vehicle runs out of fuel, the lamp (MIL) may come on. Refuel as soon as possible. After a few driving trips, the lamp should turn off. If the lamp remains on after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.

c For additional information, see the ‘‘Malfunction indicator lamp (MIL)’’ later in this section.

FUEL GAUGE

AIC0005

This gauge indicates the approximate fuel level in the tank. The gauge may move slightly during brak- ing, turning, acceleration, or going up or down hills. The gauge needle remains in approximately the same position even when the ignition key is turned OFF. The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge registers E (empty).

Instruments and controls 2-5

Z X

WARNING/INDICATOR LIGHTS AND CHIMES

CHECKING BULBS With all doors closed, apply the parking brake, fasten seat belts, and turn the ignition key to the ON position without starting the engine. The following lights come on and stay on until the engine is started:

The following lights come on briefly and then go off: ABS or If any light fails to come on, indicate a burned-out bulb or an open

it may

2-6 Instruments and controls

WIC0018

the dipstick to check the oil level. See ‘‘Engine oil’’ in the ‘‘Do-it-yourself’’ section of this manual.

CAUTION

Running the engine with the oil pres- sure warning light on could cause seri- ous damage to the engine almost im- mediately. Turn off the engine as soon as it is safe to do so.

circuit in the electrical system. Have the system repaired promptly. WARNING LIGHTS

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call an autho- rized NISSAN dealer. The oil pressure warning light is not designed to indicate a low oil level. Use

Z X

Charge warning light

If the light comes on while the engine is running, it may indicate something wrong with the charging system. Turn the engine off and check the generator belt. If the belt is loose, broken, missing, or if the light re- mains on, see an authorized NISSAN dealer immediately.

CAUTION

Do not continue driving if the belt is loose, broken or missing.

Door open warning light

This light comes on when any of the doors are not closed securely while the ignition key is ON.

Seat belt warning light and chime

The light and chime remind you to fasten your seat belts. If the driver’s seat belt is NOT securely fastened when the ignition key is turned to ON or START, the chime sounds for approximately 6 seconds and the light illuminates.

in the ‘‘Seats, re- Refer to ‘‘Seat belts’’ straints and supplemental air bag systems’’ section of this manual for precautions on seat belt usage.

Supplemental air bag warning light

When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the Air Bag Supple- mental Restraint System is operational. If any of the following conditions occur, the supplemental air bag system needs servic- ing and your vehicle should be taken to an authorized NISSAN dealer: c The supplemental air bag warning light remains on after approximately 7 sec- onds.

c The supplemental air bag warning light

flashes intermittently.

c The supplemental air bag warning light

does not come on at all.

Under these conditions, the Air Bag Supple- mental restraint system may not function properly. For additional details, see ‘‘Supple- mental restraint system’’ in the ‘‘Seats, re-

straints and supplemental air bag systems’’ section of this manual.

WARNING

is on,

If the supplemental air bag warning light the supplemental air bag will not operate in an accident.

it could mean that

Low washer fluid warning light (Canada only)

This light comes on when the washer fluid is at a low level. Add washer fluid as neces- sary. See the ‘‘Do-it-yourself’’ section of this manual.

Brake warning light

functions for both the parking

This light brake and the foot brake systems. When the ignition key is in the ON position, the light comes on when the parking brake is applied, and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:

Instruments and controls 2-7

Z X

1. Check the brake fluid level. Add brake fluid in the

as necessary. See ‘‘Brake fluid’’ ‘‘Do-it-yourself’’ section of this manual.

2. If the brake fluid level is correct, have the warning system checked by an autho- rized NISSAN dealer.

WARNING

c Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your ve- hicle towed because driving it could be dangerous.

c Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel.

c If the brake fluid level is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.

2-8 Instruments and controls

ABS or

Anti-lock brake warning light

If the light comes on while the engine is running, it may indicate something is wrong with the anti-lock portion of the brake sys- tem. Have the system checked by an autho- rized NISSAN dealer. If a malfunction occurs in the system, the anti-lock function turns off, but the brakes continue to operate normally. If the light comes on while you are driv- ing, contact an authorized NISSAN dealer for repair.

Low fuel warning light

This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).

INDICATOR LIGHTS

Overdrive off indicator light

This light comes on during driving when the overdrive switch is pressed to prevent over- drive operation. The O/D OFF indicator light comes on for two seconds each time the ignition key is turned ON. This shows the light is function- ing properly. If the O/D OFF indicator light blinks for approximately 8 seconds after coming on for 2 seconds, have an authorized NISSAN dealer check the transmission and repair it if necessary. The automatic transmission is equipped with an electronic Fail-Safe mode. This sys- tem allows the vehicle to be driven even in the event of damage to the electrical cir- cuits. If this occurs, the gears automatically engage and lock into third gear. NOTE: See ‘‘Fail-safe’’ in the ‘‘Starting and driving’’ section of this manual before visit- ing an authorized NISSAN dealer.

Z X

Turn signal/hazard indicator lights

The appropriate light flashes when the turn signal lever is activated. Both lights flash when the hazard switch is turned on.

High beam indicator (Blue)

light

This light comes on when the headlight high beam is on and goes out when the low beam is selected.

Cruise indicator light

The light comes on while the vehicle speed is controlled by the cruise control system. If the CRUISE indicator blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by an authorized NISSAN dealer.

Malfunction indicator lamp (MIL)

If this indicator lamp comes on steady or blinks while the engine is running, it may

the

indicate a potential emission control mal- function. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel filler cap is installed and closed tightly, and that the vehicle has at least three gallons of fuel in the fuel tank. lamp After a few driving trips, should turn off if no other potential emission control system malfunction exists. Operation The malfunction indicator lamp will come on in one of two ways: c Malfunction indicator lamp on steady - An emission control system malfunction has been detected. Check the fuel filler cap. If the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

c Malfunction indicator lamp blinking - An engine misfire has been detected which may damage the emission control sys- tem. To reduce or avoid emission control system damage: a) do not drive at speeds above 45 MPH

(72 km/h).

b) avoid hard acceleration or deceleration. c) avoid steep uphill grades. d) if possible,

reduce the amount of

cargo being hauled or towed.

The malfunction indicator lamp may stop blinking and come on steady. Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your ve- hicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Instruments and controls 2-9

Z X

CHIMES Key reminder chime The chime sounds if the driver’s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime A chime sounds when the driver’s door is opened with the headlight control switch on (ignition switch is turned OFF). The chime will not sound when the Auto- lamp (if so equipped) shut-off delay is acti- vated. Refer to the ‘‘Autolamp Switch’’ in- structions later in this section. Turn the headlight control switch to OFF when you leave the vehicle. Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard.

2-10 Instruments and controls

THEFT WARNING (if so equipped)

IC0005

LIC0004

The theft warning system provides audio and visual alarm signals if parts of the vehicle are disturbed.

Security indicator light This light will illuminate for the theft warning system. This light blinks whenever the ignition switch is in the LOCK, OFF, or ACC posi- tion. This function indicates the security systems equipped on the vehicle are opera- tional.

Z X

How to activate the theft warning system 1. Close all windows. (The system can be the windows are

activated even if open).

2. Remove the key from the ignition switch. 3. Close all doors and the hood. 4. Push the

button on the multi-remote controller. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.

c When the

that

button is pushed with all the hazard lights flash doors locked, twice and the horn beeps once as a reminder the doors are already locked. The horn may or may not beep once. Refer to ‘‘silencing the horn beep fea- ture’’ later in this section for details.

5. Confirm that

the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then begins to flash once every three seconds. The system is now activated. If, during this 30-second time period, the door is unlocked by the key or the multi-remote

controller, or the ignition key is turned to ACC or ON, the system will not activate. If the key is turned slowly when locking the door, the system may not activate. Furthermore, if the key is turned exces- sively to the unlock position, the system may be deactivated when the key is re- moved. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again. Even when the driver and/or passengers are in the vehicle, the system will acti- vate with all doors, hood and rear door closed with the ignition key in the OFF position. Theft warning system operation The theft warning system emits the follow- ing alarm: c The headlights and tail lights flash and the horn sounds intermittently. In addi- tion, the starter motor does not operate. c The alarm automatically turns off after two to three minutes. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking a door with the key or by

pressing the remote controller.

button on the multi-

The alarm is activated when: c a door is unlocked or opened without using the key or the multi-remote control- ler. This includes unlocking the doors with the inside door lock switch.

c the hood is opened. c the ignition is placed into the ACC, ON, or START position without the key in the ignition.

How to stop the alarm The alarm stops only by unlocking a door with the key or by pressing the button on the multi-remote controller. The alarm does not stop if the ignition key is turned to the ACC or ON position.