1997 Nissan Maxima Owners Manual

TILTING STEERING WHEEL

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.

6. Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the belt is in the automatic locking mode.

7. Check to make sure that the child restraint is properly secured prior to each use. If the lap belt repeat steps 3
through 6.

locked,

is not

PD1336

Be sure to follow the child restraint manufac- turer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). (It will revert back to “emergency locking” when the belt is fully retracted.)

4. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates that the retractor is in the auto- matic locking mode. Pull up on the belt to remove any slack in the belt.

After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and will only lock during a sudden stop or impact.

SPA0111

Tilt operation Push the lock lever and while holding down, adjust the steering wheel up or down to the desired position. Push the lock lever back into place to lock the steering wheel in place.

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

2-38

Z 01.2.1/A32-D X

OUTSIDE MIRROR REMOTE CONTROL

FOLDABLE OUTSIDE MIRRORS

Push the right or left end of the switch to select the right or left outside mirror, then adjust using the control lever.

SPA0112

Push the outside mirror backward to fold it.

MPA0008

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use inside mirror or glance over your shoulder to properly judge distances to other objects.

The outside mirror will operate only when the ignition switch is in the “ACC” or “ON” position.

2-39

Z 01.2.1/A32-D X

INSIDE MIRROR

The night position will reduce glare from the headlights of vehicles behind you at night.

SPA0470

Use the night position only when neces- sary, because it reduces rear view clarity.

2-40

Z 01.2.1/A32-D X

3 Heater, air conditioner and audio system

Ventilator ................................................................... 3-2
Heater and air conditioner......................................... 3-3
Automatic air conditioner (if so equipped) ................ 3-9
Radio ....................................................................... 3-11
Antenna ................................................................... 3-28
CB radio or car phone ............................................ 3-29

Z 01.2.1/A32-D X

VENTILATOR

SAA0040

SAA0041

Center ventilators Adjust the air flow direction of ventilators.

Side ventilators Open or close, and adjust the air flow direction of ventilators.

: This symbol

indicates that the vents are closed when the vent switch is moved to the left.

: This symbol

indicates that the vents are open when the vent switch is moved to the right.

3-2

Z 01.2.1/A32-D X

HEATER AND AIR CONDITIONER

I The air conditioner cooling function operates only when the engine is run- ning.

I Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or

SAA0042A

animals.

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.

CONTROLS Fan control dial This dial turns the fan on and off, and controls fan speed. Air flow control buttons These buttons allow you to select the air flow outlets.

— Air flows from center and side venti-

lators.

— Air flows from center and side venti-

lators and foot outlets.

— Air flows mainly from foot outlets. — Air flows from defroster outlets and

foot outlets.

— Air flows mainly from defroster out-

lets.

Temperature control lever This lever allows you to adjust the temperature of the outlet air.

3-3

Z 01.2.1/A32-D X

Air recirculation button OFF position Outside air is drawn into the passenger com- partment. Use the off position for normal heater, or air conditioner operation. ON position (Indicator light ON) Interior air is recirculated inside the vehicle. Push the air recirculation button to the “ON” position when driving on a dusty road or to avoid traffic fumes and for maximum cooling when using the air conditioner. Air conditioning button This button is provided only for vehicles with air conditioner. Start the engine, move the fan control dial to the desired (1 to 4) position and push the air conditioning button to turn on the air condi- tioner. The indicator light will come on when the air conditioner is on. To stop the air con- ditioner, push the switch again to return it to the original position. The air conditioner cooling function oper- ates only when the engine is running.

HEATER OPERATION Heating This mode is used to direct hot air from the floor outlets. Some air will also come from the defrost vents.

1. Push the air recirculation button to the

“OFF” position for normal heating.

2. Push the “

” button in.

3. Turn on the fan control dial.

4. Move the temperature control lever to the desired position between the middle and the “HOT” position.

I For quick heating, move the air recirculation button to the “ON” position. Be sure to return the air recirculation button to the “OFF” position for normal heating.

Ventilation This mode directs outside air from the side and center vents.

1. Push the air recirculation button to the

“OFF” position.

2. Push the “

” button in.

3. Turn on the fan control dial.

3-4

4. Move the temperature control lever to the

desired position.

Defrosting or defogging This mode is used to defrost/defog the win- dows. 1. Push the “ ” button in. 2. Turn on the fan control dial. 3. Move the temperature control lever to the desired position between the middle and the “HOT” position.

I To quickly remove ice or fog from the windows, turn on the fan control dial to “4” and the temperature control lever to the full “HOT” position.

I When the “

” switch is pushed, the air conditioner will automatically be turned on to defog the windshield, and the air recircu- late mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.

Z 01.2.1/A32-D X

Bi-level heating This mode directs outside air from the side and center vents and hot air from the floor outlets. 1. Push the air recirculation button to the

“OFF” position.

” button in.

2. Push the “ 3. Turn on the fan control dial. 4. Normally move the temperature control le- ver to the midpoint between “HOT” and “COLD”.

Heating and defogging This mode heats the interior and defogs the windshield. 1. Push the “ 2. Turn on the fan control dial. 3. Move the temperature control lever to the desired position between the middle and the “HOT” position.

” button in.

Operating tips I Clear snow and ice from the wiper blades and air inlet in front of the wind- shield. This will improve heater opera- tion.

I When the “

” switch is pushed, the air recirculate mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.

AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (1 to 4) position and push in the air conditioning button to activate the air condi- tioner. When the air conditioner is on, cooling and dehumidifying functions will be added to the heater operation. Cooling This mode is used to cool and dehumidify. 1. Push the air recirculation button to the

“OFF” position.

” button in.

2. Push the “ 3. Turn on the fan control dial. 4. Push on the air conditioning button. The

indicator light will come on.

5. Move the temperature control lever to the

desired position.

I For quick cooling when the outside tem- perature is high, move the air recirculation button to the “ON” position. Be sure to return the air recirculation button to the “OFF” position for normal cooling.

3-5

Z 01.2.1/A32-D X

AIR FLOW CHART The chart below shows the switch and lever positions for MAXIMUM and QUICK heating, cooling or defrosting. The air recirculation switch should be in the “OFF” position for normal cooling, heating and defrosting.

Dehumidified heating This mode is used to heat and dehumidify.

1. Push the air recirculation button to the

“OFF” position.

2. Push the “

” button in.

3. Turn on the fan control dial.

4. Push on the air conditioning button. The

indicator light will come on.

5. Move the temperature control lever to the

desired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify.

1. Push the “

” button in.

2. Turn on the fan control dial.

3. Push on the air conditioning button. The

indicator light will come on.

4. Move the temperature control lever to the

desired position.

When the “ ” button is pushed, the air conditioner will automatically be turned on to defog the windshield, and the air recircu- late mode will automatically be turned off.

Outside air is drawn into the passenger com- partment to improve the defogging perfor- mance. Operating tips I Keep the windows and sun roof closed

while the air conditioner is in operation.

I After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This will allow the air conditioner to cool the interior more quickly.

I The air conditioning system should be operated for about ten minutes at least once a month. This helps prevent dam- age to the system due to lack of lubrica- tion.

I If the coolant temperature gauge exceeds the HOT position, turn the air conditioning off. See “If your vehicle overheats” in the “In case of emergency” section for additional information.

3-6

Z 01.2.1/A32-D X

SAA0058C

3-7

SAA0059C

Z 01.2.1/A32-D X

SAA0060C

3-8

SAA0061C

Z 01.2.1/A32-D X

AUTOMATIC AIR CONDITIONER (if so equipped)

Start the engine and operate the controls to activate the air conditioner. Cooling and/or dehumidified heating (Auto mode) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribu- tion and fan speed are also controlled auto- matically.

1. Push the AUTO button on. (“AUTO” will be

displayed.)

SAA0043B

2. Push

the

” “

“ ture.

temperature button ” to set the desired tempera-

set

I The air conditioner cooling function operates only when the engine is run- ning.

I Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or

animals.

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.

I Adjust the temperature set button to about

75°F (24°C) for normal operation.

I The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically. Heating (ECON mode) The air conditioner does not activate. When you need to heat only, use this mode. 1. Push the ECON (ECONOMY) button on.

(“ECON” will be displayed.)

3-9

Z 01.2.1/A32-D X

2. Push

the

” “

“ ture.

button temperature ” to set the desired tempera-

set

I The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically.

I Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.

I Not recommended if windows fog up. Dehumidified defogging 1. Push the DEF “

” button on. (The indicator light on the button will come on.) temperature button ” to set the desired tempera-

2. Push

the

set

” “

“ ture.

I To quickly remove ice or fog from the outside of the windows, push the manual fan control button “ ” and set to the ”. maximum position “

I As soon as possible after the windshield is clean, push the AUTO button to return to the auto mode.

I When the DEF “

” button is pushed, the air conditioner will automatically be

selects the air outlet to:

: Air flows from center and side ventila-

tors.

: Air flows from center and side ventila-

tors and foot outlets.

: Air flows mainly from foot outlets.

To turn system off Push the OFF button. Operating tips I When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant tem- perature warms up, the air flow from the foot outlets will operate normally.

turned on at outside temperatures above 35°F (2°C) to defog the windshield, and the air recirculate mode will automatically be turned off.

Outside air is drawn into the passenger compartment to improve the defogging per- formance.

Manual fan speed control Push the fan control button “ ally control the fan speed. I Push the AUTO button to return to auto-

” to manu-

matic control of the fan speed.

Air recirculation button Push the air recirculation button “ ” to recirculate interior air inside the vehicle. The indicator light on the switch will come on. Push it again to draw outside air into the passenger compartment. The indicator will go out. I The air recirculation button will not be acti- vated when the air conditioner is in DEF mode.

Manual air flow control button “MODE” Pushing the manual air flow control button

3-10

Z 01.2.1/A32-D X

RADIO

To turn the radio on, turn the ignition key to “ACC” or “ON”. If you listen to the radio with the engine not running, turn the key to the “ACC” position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences.

Servicing air conditioner The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lu- bricants will cause severe damage to your air conditioning system. See AIR CONDITION- ING SYSTEM REFRIGERANT AND LUBRI- CANT RECOMMENDATIONS in the TECHNI- CAL AND CONSUMER INFORMATION section of this manual. Your NISSAN dealer will be able to service your environmentally “friendly” air conditioning system.

HA1011

The sensor on the instrument panel helps maintain a constant temperature; do not put anything on or around this sensor.

3-11

Z 01.2.1/A32-D X

FM/AM RADIO WITH CASSETTE PLAYER Radio operation Push the ON/VOL knob to listen to the radio and tune in the desired station.

Pushing the “ ” button while the cas- sette tape is playing will turn off the cassette player and turn on the radio.

Turn the ON/VOL knob to adjust the volume.

Inserting a cassette tape into the cassette player while the radio is on will turn off the radio and turn on the cassette player.

The electronic tuning radio has a DIVERSITY reception system. The FM signal can reflect off of buildings or mountains. This causes offen- sive noise. The DIVERSITY system employs two antennas; one is a rod type antenna and the other is a printed antenna on the rear window. This system automatically switches to the antenna which receives less noise. Thus the radio provides high quality reception. Selecting the desired band Push the band select button “ change from AM to FM reception. The stereo indicator will glow during FM stereo

” to

SAA0044B

3-12

Z 01.2.1/A32-D X

reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. Tuning

SEEK tuning ” Push the SEEK/SCAN tuning button “ for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station.

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

”

” button.

tuning “

Manual tuning Push down either manual “ SCAN tuning Push the SEEK/SCAN tuning button “ ” for more than 1.5 seconds. SCAN tuning be- gins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five sec- ond period will stop SCAN tuning and the radio will remain tuned to that station.

AHA0040

Station memory operations Six stations can be set for each band.

1. Tune to the desired station.

2. Push the desired select button for more

3-13

Z 01.2.1/A32-D X

than 2 seconds. (For example, in the dia- gram ch2 is to be memorized. The radio mutes when the select button is pushed.) 3. The indicator “ch2” will then come on and the sound will resume. Memorizing is now complete.

4. Other buttons can be set

manner.

in the same

If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations.

Cassette tape operation Turn the ignition key to “ACC” or “ON”, then carefully insert the cassette tape into the tape door.

The cassette tape will automatically pull into the player.

Do not force the cassette tape into the tape door.

HA1078

This could cause player damage.

Adjusting tone quality Push then turn the BASS and TREB (TREBLE) control knob to obtain the most pleasant sound. Adjusting speaker sound balance Push then pull the BAL (BALANCE) control knob to adjust the volume between the right and left speakers. FADER volume control Push then pull the FADER control knob to adjust the volume between the front and rear speakers.

3-14

The cassette tape will automatically change directions to play the other side when the first side is completed. I To maintain good quality sound, NIS- SAN recommends that you use cassette tapes of 60 minutes or shorter in length. I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed

Z 01.2.1/A32-D X

cassettes may cause the cassette to jam in the player.

I Do not use cassettes that have labels which are peeling and loose. If used, the label could jam in the player. I If a cassette has loose tape,

insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.

I Over a period of

time,

the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape passes over the head. This residue ac- cumulation can cause weak or wavering sound, and should be removed periodi- cally with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.

Fast forwarding or rewinding the tape Push either the FF (forward) or REW (rewind) button for the desired direction. The indicator light on the switch will come on. APS fast forwarding or APS rewinding the tape Push either the APS (automatic program search) FF or APS REW button while the cassette tape is playing. The tape will run quickly, and stop and play at the next program. The indicator light flashes on and off while searching the program. This system searches at the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location. Changing the direction of tape play Push the PROG (program) select button.

Playing and stopping the cassette tape Pushing the PLAY/STOP button while the cas- sette tape is playing stops the tape. Pushing the button again plays the tape. Dolby NR (noise reduction) Push the “DOLBY NR” button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator will come on. Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation. Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the eject button. The cassette tape will automatically come out.

3-15

Z 01.2.1/A32-D X

FM-AM RADIO WITH CASSETTE PLAYER Radio operation Push the POWER/VOLUME control knob to listen to the radio and tune in the desired station.

Push the FM-AM band select button while the cassette tape is playing will turn off the cas- sette player and turn on the radio.

Turn the POWER/VOLUME control knob to adjust the volume.

Inserting a cassette tape into the cassette player while the radio is on will turn off the radio and turn on the cassette player.

The radio has a diversity reception system. The FM signal can reflect off of buildings or mountains. This causes offensive noise. The diversity system employs two antennas; one is a rod type antenna and the other is a printed antenna on the rear window. This system automatically switches to the antenna which receives less noise. Thus the radio provides high quality reception. Selecting the desired band Push the band select button FM-AM band

SAA0233

3-16

Z 01.2.1/A32-D X

select to change the reception as follows: FM1 , FM2 , AM The stereo indicator will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. Tuning

SEEK tuning ” or Push the SEEK/SCAN tuning button “ “ ” for less than 1.5 seconds. SEEK tun- ing begins and stops at the next broadcasting station.

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

”.

” or “

tuning button

Manual tuning Push down either manual “ SCAN tuning Push the SEEK/SCAN tuning button “ ” or “ ” for more than 1.5 seconds. SCAN tuning begins and stops at each broadcasting station for five seconds. Pushing the button again during this five second period will stop SCAN tuning and the radio will remain tuned to that station.

SAA0234

Twelve stations can be set for the FM band (FM1 and FM2).

Six stations can be set for the AM band.

1. Tune to the desired station using the

SEEK/SCAN or TUNE button.

3-17

Z 01.2.1/A32-D X

2. Push the desired station select button for more than 1.5 seconds. (For example, in the diagram ch2 is to be memorized. The radio mutes when the select button is pushed.)

3. Other buttons can be set

manner.

in the same

If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations.

Adjusting tone quality and speaker sound balance Push the AUDIO switch to change the display as follows: BAS , TRE , FAD , BAL BAS (bass) and TRE (treble) adjust the tone quality button “ ” to the most pleasing level. The indicator light will show the level of the tone quality. FAD (fader) adjusts the speaker sound bal- ance between the front ” and rear “ ” speakers, and BAL (balance) adjusts the speaker sound balance between the right

by ” or “

pushing

control

the

“

SAA0235

” and left “

” speakers by pushing “ the control button. The indicator light will show the level of the speaker sound balance. Cassette tape operation then Turn the ignition key to ACC or ON, carefully insert the cassette tape into the tape door. The cassette tape will automatically pull into the player.

3-18

Z 01.2.1/A32-D X

Do not force the cassette tape into the tape door.

This could cause player damage.

The cassette tape will automatically change directions to play the other side when the first side is completed.

The indicator light will run when the tape is playing. Precautions on cassette player operation I To maintain good quality

sound, NISSAN recommends that you use cas- sette tapes of 60 minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

I Do not use cassettes that have labels which are peeling and loose. If used, the label could jam in the player. I If a cassette has loose tape,

insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.

I Over a period of

time,

the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape passes over the head. This residue ac- cumulation can cause weak or wavering sound, and should be removed periodi- cally with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.

Fast forwarding or rewinding the tape Push either the FF (forward) or REW (rewind) button for the desired direction. The indicator light will run with quick intervals when the FF or REW function is started.

APS fast forwarding or APS rewinding the tape Push either the APS (automatic program search) FF or APS REW button while the cassette tape is playing. The tape will run quickly, and stop and play at the next program. The indicator light will run with quick intervals when the APS FF or APS REW function is started.

This system searches at the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location. Changing the direction of tape play Push the PROG (program) select button. Playing and stopping the cassette tape Pushing the PLAY/STOP button while the cas- sette tape is playing stops the tape. Pushing the button again plays the tape. Dolby NR (noise reduction) Push the DOLBY NR “ ” button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator will come on.

3-19

Z 01.2.1/A32-D X

Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation. Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the EJECT “ ” button. The cassette tape will automatically come out.

3-20

Z 01.2.1/A32-D X

3-21

SAA0204

Z 01.2.1/A32-D X

To turn the radio off, press the POWER/ VOLUME knob. Turn the POWER/VOLUME control knob to adjust the volume.

FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC PLAYER AUDIO MAIN OPERATION Head unit

The radio has an FM Diversity reception sys- tem, which employs two antennas. One is a rod type antenna; the other is an antenna printed on the window. This system automati- cally switches to the antenna which is receiv- ing less noise.

The tape deck employs a permalloy head which allows for improved reproduction of high frequency ranges. Noise is also greatly re- duced by the combined use of the Dolby NR (noise reduction) system. Power/Volume control Turn the ignition key to “ACC” or “ON”, and then push the POWER/VOLUME knob while the system is off to call up the mode (radio, tape or CD) which was playing immediately before the system was turned off. When no CD or tape is loaded, the radio will come on. While the the POWER/VOLUME knob turns the system off.

pushing

system

on,

is

SAA0194

Adjusting tone quality Push then turn the BASS and TREB (TREBLE) control knobs to obtain the most pleasant sound.

3-22

Z 01.2.1/A32-D X

RADIO OPERATION FM(cid:215) AM band select button

TUNE button

Pushing the FM(cid:215) AM band select button will change the band. When FM(cid:215) AM band select button is pushed while the ignition switch is at “ACC” or “ON”, the radio will come on at the station last played. The last station played will also come on when the power knob is turned to ON. If a compact disc or tape is inserted when the power knob is turned to ON, the compact disc or tape will automatically be turned off and the last radio station played will come on. The FM stereo indicator “ST” will glow during FM stereo reception. When the stereo broad- cast signal is weak, the radio will automatically change from stereo to monaural reception.

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

Use these buttons for manual tuning. If the TUNE button is pushed for less than 0.5
seconds, the frequency moves by an incre- ment of 1 step. To move quickly through the channels, hold either of the TUNE buttons down for more than 0.5 seconds.

SAA0190

Adjusting speaker sound balance Push then pull the BAL (BALANCE) control knob to adjust the volume between the right and left speakers. Fader volume control Push then pull the FADER control knob to adjust the volume between the front and rear speakers.

3-23

Z 01.2.1/A32-D X

SEEK/SCAN tuning buttons

Station memory operations

SEEK tuning Push the SEEK/SCAN tuning button “ ” or “ ” for less than 1.5 seconds. SEEK tun- ing begins from low to high frequencies and stops at the next broadcasting station. SCAN tuning Push the SEEK/SCAN tuning button “ ” or “ ” for more than 1.5 seconds. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five seconds period will stop SCAN tuning and the radio will remain tuned to that station. If the SEEK/SCAN tuning button is not pushed within five seconds, SCAN tuning moves to the next station.

3-24

SAA0191

Z 01.2.1/A32-D X

Twelve stations can be set for the FM band.

Six stations can be set for the AM band.

1. Tune to the desired station using the

SEEK/SCAN or TUNE button.

2. Push the desired station select button for more than 1.5 seconds. (For example, in the diagram ch2 is to be memorized. The radio ceases emitting sounds when the select button is pushed.)

3. The indicator “ch2” will then come on and the sound will resume. Memorizing is now complete.

4. Other buttons can be set

in the same

manner.

If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations. CASSETTE TAPE PLAYER OPERATION Turn the ignition key to “ACC” or “ON”, and then lightly insert the cassette tape into the tape door. The cassette tape will be automati- cally pulled into the player.

The radio or CD will turn off (if it is on) and the cassette tape will begin to play.

Do not force the cassette tape into the tape door. This could cause player damage.

If the system is turned off by pushing the POWER/VOLUME knob with the cassette tape still in the player, the tape will resume playing when the system is turned back on. TAPE button I When this button is pushed with the system turned off and a tape loaded, the system will come on and the tape will play.

I When this button is pushed with either the radio or compact disc turned on and the tape loaded, the compact disc or the radio will automatically be turned off and the tape will play.

While the tape is playing, pushing the TAPE button stops the tape. Pushing the button again allows the tape to play. FF (fast forward), REW (rewind) button Push the FF (fast forward) button to fast for- ward the tape. To rewind the tape, push the

3-25

”, “

”, “

REW (rewind) button. Either the indicator light ” will come “ on when the FF or REW function is started. APS (automatic program search) FF, APS REW button

” or “

When the APS FF button is pushed while the tape is being played, the next program will start to play from the beginning. Push the APS FF button several times to skip through pro- grams. The tape will advance the number of times the button is pushed (up to 9 programs). When the APS REW button is pushed once, the program being played starts over from the beginning. Push several times to fast rewind programs. The tape will go back the number of times the button is pushed. Either the indicator light “ ” will come on when the APS FF or APS REW function is started. This system searches for the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location.

” or “

”, “

”,“

Z 01.2.1/A32-D X

PROG (program) button Push the PROG (program) button to change the tape side while the tape is being played.

The cassette tape will automatically change directions to play the other side when the first side is completed. Dolby NR (noise reduction) button “DOLBY NR” button for Dolby Push the NR encoded tapes to reduce high frequency tape noise. The indicator will come on. Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation. Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT button When this button is pushed with the tape loaded, the tape will be ejected. When the tape is ejected while it played, the system will be turned off.

is being

Precautions on cassette tape player operation I To maintain good quality

sound, NISSAN recommends that you use cas- sette tapes of 60 minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, moisture or magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

I Do not use cassettes that have peeling or loose labels. If used, the label could jam in the player.

I If a cassette has loose tape,

insert a pencil through one of the cassette hubs and rewind the tape firmly. Loose tape may cause jamming and wavering sound quality.

I Over a period of

the playback head, capstan and pinch roller may gather a tape coating residue as the tape passes over the head. This residue ac-

time,

cumulation can cause a weak or waver- ing sound and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be disas- sembled for cleaning.

COMPACT DISC (CD) PLAYER OPERATION Turn the ignition key to the “ACC” or “ON” position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. After loading the disc, the number of tracks on the disc and the play time will appear on the display. If the radio or tape is already operating, it will automatically turn off and the compact disc will play.

Do not force the compact disc into the slot. This could damage the player.

If the system has been turned off while the compact disc was playing, pushing the

3-26

Z 01.2.1/A32-D X

disc. The same program may be repeated twice. (no mark): All the programs will be played in sequence and stop when the last program is finished. I When the compact disc is ejected, the play pattern will automatically change to ALL.

CD EJECT button When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected. When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off.

POWER/VOLUME knob will start the compact disc. 8 cm diameter compact discs can also be used without an adapter. CD button When this button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When this button is pushed with the compact disc loaded but the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play. When this button is pushed while the compact disc is playing, the compact disc will stop playing. When this button is pushed with the compact disc stopped, the compact disc will start to play. FF (fast forward), REW (rewind) button When the FF (fast forward) or REW (rewind) button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is released, the compact disc will return to normal play speed.

APS (automatic program search) FF, APS REW button

When the APS FF button is pushed while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will advance the number of times the button is pushed. (When the last program on the compact disc is skipped through, the first program will be played.) When the APS REW button is pushed, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed. PROG (program) button When this button is pushed while the compact disc is being played, the play pattern will change as follows: ALL: All the programs will be played repeat- edly in sequence. 1: Only one program (the one being played when the PROG (program) button is pushed) will be repeated. RANDOM: Programs will be played at random, not following the sequence on the compact

3-27

Z 01.2.1/A32-D X

If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it. (without 8 cm diameter com- pact discs) DISC indicator light This light comes on when the compact disc is loaded.

I During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

I The player may skip while driving on

rough roads.

I The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.

I Do not expose the CD to direct sun-

light.

I Do not use an 8 cm CD adapter as this

will cause malfunction.

ANTENNA

Power antenna The antenna will automatically extend when the radio is turned on, and retract when switched off. If the radio is left on, the antenna will retract and extend with the ignition key “OFF-ON” operation.

I Before turning the radio on, make sure that there is no one near the antenna outlet and there is enough space for it to extend.

I To prevent damage, be sure that an- tenna is fully retracted before the vehicle enters an automated car wash.

I Dirt and other foreign matter on the power antenna rod may interrupt its operation. Clean the rod periodically with a damp cloth. This type of clean- ing is especially important during the winter seasons in areas where road salt and other chemicals may be spread and surfaces splashed onto the antenna rod.

road

on

3-28

Z 01.2.1/A32-D X

CB RADIO OR CAR PHONE

When installing a CB, ham radio or a car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equip- ment may adversely affect the MFI (Multiport Fuel Injection) system and other electronic parts.

I Keep the antenna as far as possible away from the Engine Control Mod- ule.

I Also keep the antenna wire more than 8 in (20 cm) away from the MFI har- ness. Do not route the antenna wire next to any harness.

I Adjust the antenna standing-wave ra- tio as recommended by the manufac- turer.

I Connect the ground wire from the CB

radio chassis to the body.

I For details, consult a NISSAN dealer.

3-29

Z 01.2.1/A32-D X

MEMO

3-30

Z 01.2.1/A32-D X

4 Starting and driving

Precautions when starting and driving...................... 4-2
Avoiding collision and rollover................................... 4-3
Drinking alcohol/drugs and driving............................ 4-4
Ignition switch............................................................ 4-4
Before starting the engine......................................... 4-6
Starting the engine.................................................... 4-6
Driving with automatic transmission.......................... 4-7
Driving with manual transmission ........................... 4-10
Parking brake .......................................................... 4-12
Cruise control .......................................................... 4-13
Break-in schedule ................................................... 4-15
Economy hints......................................................... 4-15
Parking/Parking on hills........................................... 4-16
Power steering system............................................ 4-17
Brake system .......................................................... 4-17
Anti-lock brake system (ABS) (If so equipped)....... 4-18
Cold weather driving ............................................... 4-19

Z 01.2.1/A32-D X

PRECAUTIONS WHEN STARTING AND DRIVING

Do not leave children, unreliable adults, or pets alone in your vehicle. They could accidentally injure themselves or others through inadvertent operation of the ve- hicle. Also, on hot, sunny days, tem- peratures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

EXHAUST GAS (Carbon Monoxide)

Do not breathe exhaust gases; they con- tain colorless and odorless carbon mon- oxide. Carbon monoxide is dangerous. It can cause unconsciousness or death. I If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.

I Do not run the engine in closed

spaces such as a garage.

I Do not park the vehicle with the en- gine running for any extended length of time.

I Keep the trunk lid, or back door closed while driving, otherwise ex- haust gases could be drawn into the passenger compartment. If you must drive in this manner for some reason, take the following steps.

1. Open all the windows.

2. Set

the air

recirculate switch “OFF” and the fan control at “high” to circulate the air.

monoxide entry into the vehicle. (Some recreational vehicle appli- ances such as stoves, refrigerator, heaters, etc. may also generate car- bon monoxide.)

I The exhaust system and body should be inspected by a qualified mechanic whenever:

a. The vehicle is raised for service.

b. You suspect that exhaust fumes are entering into the passenger compartment.

c. You notice a change in the sound

3. Be sure the rear seat armrest and

of the exhaust system.

tray are closed.

I If electrical wiring or other cable con- nections must pass to a trailer through the seal on the trunk lid or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.

I If a special body or other equipment is added for recreational or other us- age, follow the manufacturer’s rec- ommendation to prevent carbon

4-2

d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.

THREE WAY CATALYST The three way catalyst is an emission control device installed in the exhaust system. Ex- haust gases in the converter are burned at high temperatures to help reduce pollutants.

Z 01.2.1/A32-D X

I The exhaust gas and the exhaust sys- tem are very hot. Keep people or flammable materials away from the exhaust pipe.

I Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

I Do not use leaded gasoline. Deposits from leaded gasoline seriously re- duce the three way catalyst’s ability to help reduce exhaust pollutants.

I Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the converter, caus- ing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle inspected promptly

by an authorized NISSAN dealer.

I Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three way catalyst.

I Do not race the engine while warming

it up.

I Do not push or tow your vehicle to

start the engine.

AVOIDING COLLISION AND ROLLOVER

Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.

Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steer- ing maneuvers, because these driving prac- tices could cause you to lose control of your vehicle. As with any vehicle, a loss of con- trol could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Seat Belts” section of this manual, and also instruct your passengers to do so.

4-3

Z 01.2.1/A32-D X

DRINKING ALCOHOL/DRUGS AND DRIVING

IGNITION SWITCH

Never drive under the influence of alco- hol or drugs. Alcohol in the blood stream reduces coordination, delays re- action time and impairs judgment. Driv- ing after drinking alcohol increases the likelihood of being involved in an acci- dent injuring yourself and others. Addi- tionally, if you are injured in the accident alcohol can increase the severity of injury.

Nissan is committed to safe driving. But, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol related accidents. Although the local laws vary on what is con- sidered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that’s true for drugs too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.

To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left.

Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or per- sonal injury.

SSD0021

The switch includes an anti-theft steering lock device.

“LOCK” Normal parking position (0)

The ignition key can only be removed when the switch is in this position. On manual transmission models, to turn the ignition key to “LOCK” from “ACC” or “ON”, turn the key to “OFF” and press in the key release button, then turn the key to “LOCK”. In order for the steering wheel to be locked, it must be turned about 1/6 of a turn counter- clockwise from the straight up position. To lock the steering wheel, remove the key.

4-4

Z 01.2.1/A32-D X

1) Move the selector lever into the “P” posi-

tion.

2) Turn the ignition key slightly in the “ON”

direction.

3) Turn the key toward the “LOCK” position. 4) Remove the key. If the key is removed from the ignition switch, the selector lever cannot be moved from “P” (Park). The selector lever can be moved if the ignition switch is in the “ACC” position. The selector lever can also be moved if the ignition switch is in the “ON” position and the foot brake pedal is depressed. There is an “OFF” position in between “LOCK” and “ACC”, although it does not show on the lock cylinder. When the ignition is in “OFF” the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/6 of a turn counter- clockwise from the straight up position.

To lock the steering wheel, remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left.

Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or per- sonal injury.

“OFF” (1) The engine can be turned off without locking the steering wheel. “ACC” (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. “ON” Normal operating position (3) This position turns on the ignition system and the electrical accessories.

4-5

Z 01.2.1/A32-D X

SSD0055

On automatic transmission models, the igni- tion lock is designed so that the key cannot be turned to “LOCK” and removed until the selec- tor lever is moved to the “P” position.

When removing the key from the ignition, make sure the selector lever is in the “P” position.

the selector lever is not returned to “P” the key cannot be moved toward

If (Park), LOCK.

When the key cannot be turned toward the “LOCK” position, proceed as follows to remove the key:

“START” (4) This position activates the starter motor, start- ing the engine.

BEFORE STARTING THE ENGINE

STARTING THE ENGINE

I Make sure the area around the vehicle is

clear.

I Maintenance items listed here should be checked periodically, e.g., each time you check engine oil.

I Check that all windows and lights are clean. I Visually inspect tires for their appearance and condition. Also check tires for proper inflation.

I Lock all doors. I Position seat and adjust head restraints. I Adjust inside and outside mirrors. I Fasten seat belts and ask all passengers to

do likewise.

I Check the operation of warning lights when

key is turned to the “ON (3)” position.

1. Apply the parking brake. 2. Automatic transmission:

Move the selector lever to “P” (Park) or “N” (Neutral). (“P” preferred.) The selector lever cannot be moved out of “P” and into any of the other gear positions if the key is removed from the switch. The starter is designed not to operate if the selector lever is in one of the driving positions. Manual transmission:

Move the gearshift lever to “N” (Neutral), and depress the clutch pedal to the floor while cranking the engine. The starter is designed not to operate unless the clutch pedal is depressed.

3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to “START”. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. — If the engine is very hard to start in extremely cold or hot weather, depress the accelerator pedal and hold it to help start the engine.

4-6

Z 01.2.1/A32-D X

— In the summer, when restarting the engine within 30 minutes after it has been stopped, keep the accelerator pedal fully depressed while starting.

Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, other- wise the starter could be damaged.

4. Warm-up

least 30
Allow the engine to idle for at seconds after starting. Drive at moderate speed for a short distance first, especially in cold weather.

DRIVING WITH AUTOMATIC TRANSMISSION The automatic transmission in your vehicle is electronically controlled by a microcomputer to produce maximum power and smooth opera- tion. Shown on the following pages are the recom- mended operating procedures for this trans- mission. Follow these procedures for maxi- mum vehicle driving enjoyment. Starting the vehicle I After starting the engine, fully depress the foot brake pedal and push the selector lever button before shifting the selector lever to the “R”, “N”, “D”, “2” or “1” position. Be sure the vehicle is fully stopped before attempt- ing to shift the selector lever.

performance

and

This automatic transmission is designed so that the foot brake pedal MUST be de- pressed before shifting from “P” to any drive position while the ignition switch is “ON”. The selector lever cannot be moved out of “P” and into any of the other gear positions if the key is turned to the “LOCK” position or if the key is removed from the switch. When the battery charge is low, the selec- tor lever can be moved if the ignition switch is in the “ACC” position.

4-7

1. Keep the foot brake pedal depressed and

shift into a driving gear.

2. Release the parking brake and foot brake, then gradually start the vehicle in motion.

I Do not depress the accelerator pedal while shifting from “P” or “N” to “R”, “D”, “2” or “1”. Always depress the brake pedal until shifting is com- pleted. Failure to do so could cause you to lose control and have an acci- dent.

I Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.

I On slippery roads, do not down shift.

This may cause a loss of control.

I Never shift to “P” or “R” while vehicle is moving. This could cause an accident.

Z 01.2.1/A32-D X

When stopping the vehicle on an uphill grade, do not hold the vehicle by de- pressing the accelerator pedal. The foot brakes should be used for this purpose.

Shifting from “P” (Park) If the ignition switch is in the “ON” position and the foot brake pedal the selector lever still cannot be moved out of “P” (Park), follow these instructions:

is depressed, but

1. Shut the engine off and remove the key.

2. Apply the parking brake.

3. Reinsert the ignition key and turn it clock-

wise to the “ACC” position.

4. Depress the brake pedal, move the selector lever to “N” (Neutral) and start the engine.

5. Check stop light operation.

If the selector lever cannot be moved from the “P” position while the engine is running and the brake pedal depressed, the stop lights may not work. Malfunc- tioning stop lights could cause an acci- dent injuring yourself and others.

These instructions for starting the vehicle in “N” (Neutral) should only be used until service can be obtained. Never drive the vehicle if the stop lights are not operating properly.

SD1003M

Push the button to shift into “P”, “R” or from “D” to “2”. All other positions can be selected without pushing the button.

“P” (Park):

Use this selector position when the vehicle is parked or when starting the engine. Always be sure the vehicle is at a complete stop. For maximum safety, depress the brake pedal, then push in the select lever button and move the lever to the “P” position. Apply the parking brake. When parking on a hill, apply the park- ing brake first, then shift the lever into the “P” position.

4-8

Z 01.2.1/A32-D X

“R” (Reverse):

Use this position to back up. Always be sure the vehicle is completely stopped. With the brake pedal depressed, push in the select lever button and move the lever to the “R” position

Accelerator downshift — In “D” position — For rapid passing or hill climbing, fully depress the accelerator pedal to the floor. This shifts the transmission down into second gear or first gear, depending on the vehicle speed.

“N” (Neutral):

Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to “N” and restart a stalled engine while the vehicle is moving.

“D” (Drive):

Use this position for all normal forward driving.

“2” (Second gear): Use for hill climbing or engine braking on downhill grades. Do not exceed 73 MPH (117 km/h) in the “2” position. “1” (Low gear): Use this position when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. Do not exceed 40 MPH (65 km/h) in the “1” position.

SD1007

Overdrive switch ON:

For normal driving, push the overdrive switch “ON ” with the selector switch in the “D” position. The trans- mission is upshifted into OVERDRIVE as the vehicle speed increases.

The overdrive will not engage until the engine has warmed up.

OFF:

For driving up and down long slopes where engine “braking” would be ad- vantageous, push the switch “OFF ”. When cruising at a low speed or climbing a gentle slope, you may

4-9

Z 01.2.1/A32-D X

feel uncomfortable shift shocks as the transmission shifts between 3rd and overdrive repeatedly. In this case, set the overdrive switch in the “OFF ” position. The indicator light will come on at this time.

the

in the “OFF

When driving conditions change, reset overdrive switch in the “ON ” position. Remember not to drive at high speeds for extended periods of time with the overdrive switch set ” position. This reduces the fuel economy. Fail-safe When the Fail-safe operation occurs, the next time the key is turned to the “ON” position, the O/D OFF light will blink for approximately 8
seconds after coming on for 2 seconds. While the vehicle can be driven under these circum- stances please note that the gears in the automatic transmission will be locked in third gear.

DRIVING WITH MANUAL TRANSMISSION

If the vehicle is driven under extreme con- ditions, such as excessive wheel spinning and subsequent hard braking, the Fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition key “OFF” and wait for 3 seconds. Then turn the key back to the “ON” position. The vehicle should return to its normal operat- ing condition. If it does not return to its normal operating condition, have your NIS- SAN dealer check the transmission and repair if necessary.

SSD0002

fully depress the clutch To change gears, pedal, then move the shift lever. After shifting, release the clutch slowly. On the 5-speed transmission model, you can- not shift directly from 5th gear into Reverse. First shift into Neutral, then into Reverse. If lever into Reverse or 1st, shift into Neutral, then release the clutch pedal and shift into Reverse or 1st again.

to move the shift

is difficult

it

4-10

Z 01.2.1/A32-D X

for shifting into a higher gear. These sugges- tions relate to fuel economy and vehicle per- formance. Actual shift-up speeds will vary ac- cording to road conditions, the weather and individual driving habits. For normal acceleration in low altitude areas [less than 4,000 ft (1,219 m)]: shift

CRUISE shift

ACCEL

Gear change

point

point

MPH (km/h)

MPH (km/h)

1st to 2nd

2nd to 3rd

3rd to 4th

4th to 5th

13 (24)

23 (40)

33 (58)