Download PDF Manual


IC1284MA


IC1292


” position.


The instrument brightness control operates when the light switch is in the “ ” or “ Turn the control to adjust the brightness of instrument panel lights (except clock) and power window switch lights. When the control is turned to the right until a click sound is heard, the light intensity will be at maximum. When the control is turned to the left until a click sound is heard, the light will be turned off.


To turn the fog lights on, turn the headlight switch to the “ ” position, then turn the switch to the “ ” position. To turn them off, turn the switch to the “OFF” position. The headlights must be on for the fog lights to operate.


1-15


Z 01.2.1/A32-D X


HAZARD WARNING FLASHER SWITCH


HEATED SEATS (If so equipped)


on the highway unless unusual cir- cumstances force you to drive so slowly that your vehicle might be- come a hazard to other traffic.


I Turn signals do not work when the


switch is operating.


The flasher can be actuated with the ignition switch either off or on.


SIC0178


Push the switch on to warn other drivers when you must stop or park under emergency con- ditions. All turn signal lights will flash. Some state laws may prohibit the use of the hazard warning flasher switch while driv- ing.


I When stalled or stopped on the road- way under emergency conditions, move the vehicle well off the road.


I Do not use the switch while moving


SIC0693


The front seats are warmed by built-in heaters. The switches located on the center console can be operated independently of each other.


1. Start the engine.


The battery could run down if the seat heater is operated while the engine is not running.


2. Selecting heat range.


1-16


Z 01.2.1/A32-D X


I For Low heat, press the top of


the


switch.


I For High heat, press the bottom of the


switch.


I For No heat, the switch has a center “OFF” position between Low and High.


The indicator light in the switch will illumi- nate when Low or High is selected.


The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.


3. When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn the switch off.


Do not use the seat heater for extended periods, or when the seat is not occu- pied. I Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.


I Do not place anything hard or heavy


on the seat or pierce it with a pin or similar object. This may result in damage to the heater.


I Any liquid spilled on the heated seat should be removed immediately with a dry cloth.


I When cleaning the seat, never use benzine, thinner, or any similar mate- rials.


I If any abnormalities are found or the heated seat does not operate, turn the switch OFF and have the system checked by your NISSAN dealer.


CIGARETTE LIGHTER AND ASH TRAYS


SIC0694


The cigarette lighter element is an accessory. A genuine NISSAN cigarette lighter or equiva- lent can be purchased from your local NISSAN dealer. The cigarette lighter operates when the igni- tion switch is in the “ACC” or “ON” position. Push the lighter in all the way. When the lighter is heated, it will spring out. Return the lighter to its original position after use.


1-17


Z 01.2.1/A32-D X


POCKET


given to the driving operation.


The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation.


The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.


SIC0181


The pocket should not be used while driving in order that full attention may be


1-18


Z 01.2.1/A32-D X


CUP HOLDER


POWER WINDOW


I Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your pas- senger.


I Use only soft cups in the cup holder. Hard objects can injure you in an accident.


SIC0695


SIC0182


The cup holder should not be used while driving in order that full attention may be given to the driving operation.


I Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.


I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls and become trapped in a window. Unattended children could become


1-19


Z 01.2.1/A32-D X


involved in serious accidents.


The power window only operates when the ignition key is in the “ON” position. To open or close the window, push down or pull up the switch and hold it. The main switch (driver side switches) will open or close all the windows. Locking passenger’s window When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.


SIC0183


SIC0184


The passenger side switch will open or close only the corresponding window. To open or close the window, hold the switch down or up.


Automatic operation To fully open the driver side window, com- pletely push down the switch and release it; it need not be held. The window will automati- cally open all the way. To stop the window, just pull up the switch toward the “CLOSE” side. A light press on the switch will cause the window to open until the switch is released.


1-20


Z 01.2.1/A32-D X


SUNROOF (If so equipped)


Sun shade Open/close the sun shade by sliding it backward/forward. The shade will open automatically when the sunroof is opened. However, it must be closed manually.


If the sunroof does not close Have your NISSAN dealer check and repair the sunroof.


IC1432


The sunroof will only operate when the ignition key is in the “ON” position. Sliding the sunroof To open the roof, keep pressing the switch to the “


” side.


” side.


To close the roof, keep pressing the switch to the “ Tilting the sunroof To tilt up, first close the sunroof, then keep pushing the “ ” side of the tilt switch. To tilt down the “


sunroof,


pushing


” side.


keep


the


I In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints properly.


I Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the roof is closing.


I Remove water drops, snow,


ice or sand from the sunroof before open- ing.


I Do not place any heavy object on the


sunroof or surrounding area.


1-21


Z 01.2.1/A32-D X


and the driver’s door is opened and then closed.


The timer is cancelled, and the interior light will turn off when: I The driver’s door is locked. I The ignition switch is turned “ON”.


Leaving the interior light switch in the ON position for extended periods of time will result in a discharged battery.


CLOCK


INTERIOR LIGHT


AIC0500


IC1226


The digital clock displays time when the igni- tion key is in “ACC” or “ON”. If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time. Adjusting the time Push the H button to adjust the hour. Push the M button to adjust the minute.


The interior light has a three-position switch. When the switch is in the center “q” position, the light will illuminate when a door is opened. Interior light timer The interior light will stay on for about 30
seconds when: I The driver’s door is unlocked while the key


is removed from the ignition switch.


I The key is removed from the ignition switch


while the driver’s door is closed.


I The key is removed from the ignition switch


1-22


Z 01.2.1/A32-D X


FRONT PERSONAL LIGHT


VANITY MIRROR LIGHT


TRUNK LIGHT


illuminates when the trunk lid is The light opened. When the trunk lid is closed, the light will go off.


IC1019


SIC0186


The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.


IC1163-A


1-23


Z 01.2.1/A32-D X


INTEGRATED HomeLink TRANSMITTER (If so equipped) The Integrated HomeLink Transmitter pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. THE INTEGRATED HomeLink TRANSMITTER: I will operate garage doors, gates, home/ office lighting systems and security sys- tems by storing and transmitting the pro- gramming information of your current hand- held transmitters.


I is built-in and powered by your vehicle’s battery and charging system. No separate batteries are necessary.


Do not use this Integrated HomeLink Transmitter with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards (these standards be- came effective for models manufactured after April 1, 1982). A garage door opener which cannot “detect” an object in the path of a closing garage door and then automatically stop and reverse the door, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death.


PROGRAMMING THE HomeLink TRANSMITTER


SIC0696


During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.


Your vehicle’s engine should be turned off while programming your transmitter.


1-24


Z 01.2.1/A32-D X


The Integrated HomeLink Transmitter may not work with older garage door openers that do not meet current Fed- eral Consumer Safety Standards.


1. Test the Integrated HomeLink Transmitter by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3.


2. Clear all channels on the Integrated HomeLink Transmitter by holding down both outside buttons (#1 & #3) until the red light begins to flash rapidly (approximately 20 seconds). Then release both buttons.


3. Select which of


the three Integrated HomeLink Transmitter buttons you want to program.


4. Hold your hand-held transmitter against the bottom surface of the Integrated HomeLink Transmitter so that you can still see the


red indicator light.


5. Press the desired button until the red indi- cator light flashes slowly. Do not release the button. Continue holding and press the hand-held transmitter button through step 6.


6. Hold


until


buttons


Transmitter


the both down light on the Integrated red indicator flashes rapidly HomeLink (This may take 1-90 seconds). Then re- lease both buttons. The rapid flashing means that the transmitter has been suc- cessfully programmed to match your hand- held transmitter. You can now use the Integrated HomeLink Transmitter instead of your hand-held transmitter.


to 1992, D.O.C.


Note to Canadian users: Prior regulations required many hand-held transmitters to stop transmit- ting after one or two seconds, even though you continue to hold down the button. If you think you have one of these hand-held transmitters, you should press and re-press the transmitter button every 2 seconds without ever releasing the integrated HomeLink Transmitter button. The indicator light on the Integrated HomeLink Transmitter should blink rapidly indicating a successful programming procedure. If it re- turns to the slow blink of program mode, continue to periodically reactivate your hand- held transmitter until a successful program- ming procedure is indicated by the rapidly flashing indicator light.


OPERATING THE TRANSMITTER To operate, simply press the appropriate but- ton on the Integrated HomeLink Transmitter. The red indicator light illuminates while the signal is being transmitted. The effective trans- mission range of the Integrated HomeLink Transmitter may differ from your hand-held transmitter. PROGRAMMING PROBLEM DIAGNOSIS Be sure to keep your original hand-held trans- mitter for possible reprogramming if neces- sary. I Make sure batteries in the hand-held trans-


mitter are fully charged.


I Hold your hand-held transmitter against the bottom surface Integrated HomeLink Transmitter so that you can still see the red indicator light.


the


of


I Hold buttons for duration of the program-


ming without interruption.


I Rotate your hand-held transmitter end- over-end and program again. For best re- sults, place the end opposite the battery compartment Integrated


against


the


1-25


Z 01.2.1/A32-D X


HomeLink ming.


Transmitter when program-


SPA0609


ROLLING CODES (If so equipped) If your hand held transmitter appears to train to the HomeLink Transmitter, but does not open your garage door, and your garage door opener was manufactured after 1995, your garage door opener may have a “Code Pro- tected” or “Rolling Code” feature. This type of system will change the “code” of your garage door opener every time you open or close your garage door. To determine if you have one of these sys- tems, depress the button on the HomeLink Transmitter that you have just programmed. If the LED on the HomeLink Transmitter


1-26


flashes rapidly for 1 to 2 seconds, then re- mains on, your garage door opener has a rolling code system.


To operate your “Rolling Code” garage door opener from your HomeLink Transmitter, fol- low these steps:


1. Program your hand held transmitter to the HomeLink Transmitter by following the procedures outlined above (if not yet pro- grammed).


2. Program your garage door opener receiver to recognize your HomeLink Transmitter (The HomeLink Transmitter follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed):


a) Remove the cover panel from your ga- rage door opener receiver. The receiver should be located by the garage door opener motor.


b) Locate the training button on the garage door opener receiver. The exact location and color of the button may vary by garage door opener brand. If you have difficulty locating the training button, ref- erence opener manual. If you have difficulty program- ming your garage door opener equipped


garage


door


your


Z 01.2.1/A32-D X


15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. DOC: ISTC 1763K1313
FCC I.D.: CB2V67690


with a rolling code system to recognize the HomeLink Transmitter with the “Rolling Code” feature, call NISSAN Consumer Affairs Department.


c) Press the training button on the garage door opener receiver for 1 to 2 seconds. d) Return to the HomeLink Transmitter in the vehicle, and depress the pro- grammed HomeLink button for the du- ration of the fast blink on the HomeLink Transmitter (1 to 2 seconds). Release the button, and re-press to confirm that the system has trained.


e) Your garage door opener should now recognize your HomeLink Transmitter. You may use either your HomeLink Transmitter or your original hand held transmitter to open your garage door.


CLEARING THE PROGRAMMING INFORMATION Should you sell your vehicle, be sure to clear the channels of the Integrated HomeLink Transmitter. To clear the channels, simulta- neously hold down the outside two buttons (#1
& #3) until the red indicator light begins to flash rapidly (approximately 20 seconds). This will clear all three buttons. Individual buttons can- not be cleared, but can be reprogrammed at any time by following the programming proce- dures described above. IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was Integrated HomeLink Transmitter as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those de- vices. When your vehicle is recovered, you will need to reprogram the Integrated HomeLink Transmitter with your new transmitter information. FCC Notice: This device complies with FCC rules part


programmed


into


the


1-27


Z 01.2.1/A32-D X


MEMO


1-28


Z 01.2.1/A32-D X


2 Pre-driving checks and adjustments


Key ............................................................................ 2-2
Door locks ................................................................. 2-2
Multi-remote control system (If so equipped) ........... 2-5
Hood release............................................................. 2-8
Glove box lock .......................................................... 2-8
Trunk lid lock............................................................. 2-9
Fuel filler lid lock ..................................................... 2-10
Seats ....................................................................... 2-12
Supplemental restraint system (Supplemental air bag system) ............................... 2-17
Supplemental air bag warning labels...................... 2-22
Supplemental air bag warning light......................... 2-22
Seat belts ................................................................ 2-24
Child restraints for infants and small children......... 2-31
Tilting steering wheel .............................................. 2-38
Outside mirror remote control ................................. 2-39
Foldable outside mirrors.......................................... 2-39
Inside mirror ............................................................ 2-40


Z 01.2.1/A32-D X


KEY


DOOR LOCKS


A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer or a lock smith shop.


SPA0083


The master key can be used for all the locks. Record the key number on the key number plate and keep it in a safe place (such as your wallet), NOT IN THE CAR. A key number plate is supplied with your key. Keep the plate in a safe place. NISSAN does not record key num- bers so it is very important to keep track of your key number plate.


SPA0084


Locking front doors with key To lock the door, turn the key towards the front of the vehicle. To unlock, turn it towards the rear. Locking the front door will simultaneously lock the other doors.


2-2


Z 01.2.1/A32-D X


I Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.


I Before opening any door, always look


for and avoid oncoming traffic.


I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.


SPA0086


CHILD SAFETY REAR DOOR LOCK Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, the rear door can be opened only from the outside.


SPA0085


Locking the doors without key To lock from the outside without a key, move the inside lock knob to the “LOCK” position. Then close the door. When locking the door this way, be certain not to leave the key inside the vehicle. The inside lock knob cannot be set to the “LOCK” position with the front doors open and with the key in the ignition.


2-3


Z 01.2.1/A32-D X


the “LOCK” position will lock all doors.


SPA0087


POWER DOOR LOCK The power door lock system allows you to lock or unlock all doors simultaneously. I Turning the front door key to the front of the


vehicle will lock all doors.


I Turning the front door key one time to the rear of the vehicle will unlock the corre- sponding door. From that position, return- ing the key to Neutral (where the key can only be removed and inserted.) and turning it to the rear again within 5 seconds will unlock all doors.


I Pushing the front door inside lock knob to


SPA0088
I Operating the lock-unlock switch will lock or


unlock all doors.


I Before opening any door, always look


for and avoid oncoming traffic.


I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.


2-4


Z 01.2.1/A32-D X


MULTI-REMOTE CONTROL SYSTEM (If so equipped)


It is possible to lock/unlock all doors, to open the driver’s and front passenger’s windows, to release the trunk lid and to turn on or off the interior light by using the remote controller from outside the car. Be sure to remove the key from the vehicle before locking the doors and leaving it. The remote controller can operate at a dis- tance of approximately 49 ft (15 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact your NISSAN dealer.


Listed below are conditions or occur- rences which will damage the remote controller. I Do not allow the remote controller to


become wet.


I Do not drop the remote controller. I Do not strike the remote controller


sharply against another object.


SPA0277


I Do not place the remote controller for


2-5


Z 01.2.1/A32-D X


an extended period in an area where temperatures exceed 140°F (60°C).


DOOR LOCK OPERATION 1. Remove the ignition key.


2. Close all doors.


3. Push the lock button on the remote control-


ler.


4. The hazard indicator flashes twice. 5. All doors will lock. Although door locking with the remote control- ler can be confirmed by looking at the hazard indicator, always check to be sure that the doors are properly locked before leaving your vehicle. DOOR UNLOCK OPERATION 1. Push the unlock button on the remote con-


troller.


2. Only the driver side door will unlock. Push the unlock button on the remote controller again within 5 seconds. All doors will unlock.


3. The interior light will stay on for 30 seconds when the interior light switch is in the center “q” position.


The interior light can be turned off without waiting for 30 seconds by inserting the key into the ignition and turning it “ON” or by locking the doors with the remote controller or by pushing the interior light button. OPENING THE DRIVER’S AND FRONT PASSENGER’S WINDOW 1. Push the unlock button on the remote con- troller for longer than 1.5 seconds after the driver’s door is unlocked.


2. The driver’s and front passenger’s window


will open. The driver’s and front passenger’s window will also open after all doors are unlocked with the remote controller. The driver’s and front passenger’s win- dow cannot be closed by using the re- mote controller.


TRUNK LID OPENER OPERATION 1. Push the trunk lid release button on the remote controller for longer than 0.5 sec- ond.


2. The trunk lid will open. The trunk lid will not open when the trunk lid cancel lever is in the “CANCEL” position. It can be opened only with the key.


2-6


PANIC ALARM OPERATION If you are near your vehicle and feel threat- ened, you may activate the alarm to call atten- tion as follows: 1. Push the panic alarm button on the remote


controller for longer than 1.5 seconds.


2. The theft warning alarm and headlight will


stay on for 30 seconds.


3. The alarm will stop when any of the key functions on the remote controller are used.


The remote controller will not function. I When the key is inserted into the key


switch.


I When the battery in the remote control-


ler is dead.


I The distance between the remote con- troller and vehicle is more than approx. 49 ft (15 m).


Z 01.2.1/A32-D X


Recommended battery: Sanyo CR2025 or equivalent


that may cause undesired operation of the device.


3. Close the lid securely.


4. Push the remote controller button two or


three times to check its operation.


If the battery is removed for any reason other than replacement, perform step 4
above. I An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal.


I The remote controller is water-resistant; however, if it does get wet, immediately wipe completely dry.


I When changing batteries, do not let dust


or oil get on the controller.


FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This de- vice may not cause harmful interference, and (2) this device must accept any inter- including interference ference received, 2-7


Z 01.2.1/A32-D X


SPA0090


BATTERY REPLACEMENT Replace the battery as follows:


1. Open the lid using a suitable tool.


2. Replace the battery with a new one.


HOOD RELEASE


GLOVE BOX LOCK


1. Pull the hood lock release handle q1


lo- cated below the instrument panel; the hood will then spring up slightly.


2. Pull the lever q2 at the front of the hood with


your fingertips and raise the hood.


3. When closing the hood, slowly close the


hood and make sure it locks into place.


SPA0466


SPA0092


I Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. I If you see steam or smoke coming to


from the engine compartment, avoid injury, do not open the hood.


When locking or unlocking the glove box, use the master key. The glove box may be opened by pulling the handle.


Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.


2-8


Z 01.2.1/A32-D X


TRUNK LID LOCK


push the trunk lid down securely. Type B The trunk lid release button is located under the driver’s arm rest. To open the trunk lid, push the release button. To close, push the trunk lid down securely.


SPA0093


Trunk lid release operation Type A


The trunk lid release lever is located on the outside of the driver’s seat. To open the trunk lid, pull up the trunk lid release lever. To close,


SPA0094


Key operation To open the trunk lid, turn the key clockwise. To close, lower and push the trunk lid down securely.


Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust Gas” in the “Starting and driving” section.


2-9


Z 01.2.1/A32-D X


FUEL FILLER LID LOCK


SPA0095


SPA0096


SPA0119


OPENER CANCEL LEVER FOR TRUNK LID When the lever is in the “CANCEL” position, the trunk lid cannot be opened with the trunk lid release lever or handle. It can be opened only with the key.


Opener lever Type A To open the fuel filler lid, pull the opener lever. To lock, close the fuel filler lid securely. Type B To open the fuel filler lid, push the opener lever down. To lock, close the fuel filler lid securely.


FUEL FILLER CAP The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard.


I Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seri- ously injured if it is misused or mis- handled. Always stop the engine and do not smoke or allow open flames or


2-10


Z 01.2.1/A32-D X


sparks near the vehicle when refuel- ing.


I Fuel may be under pressure. Turn the cap one-half turn and wait for any “hissing” sound to stop, to prevent fuel from spraying out and possible personal injury. Then remove the cap. I Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper opera- tion of the fuel system and emission control system. An incorrect cap can result in a serious malfunction and possible injury.


If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.


If the fuel filler cap is not tightened prop- erly, the malfunction indicator light (MIL) may come on.


Put the fuel filler cap on the cap holder while refueling.


SPA0120


2-11


Z 01.2.1/A32-D X


SEATS


SEAT ADJUSTMENT


I Do not adjust the driver’s seat while driving. The seat may move suddenly and could cause loss of control of the vehicle.


I After adjustment, gently rock in the is securely


to make sure it


seat locked.


SPA0472


SPA0473


I For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly. See “Precautions on seat belt usage” later in this chapter.


I Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.


2-12


Z 01.2.1/A32-D X


Forward and backward Pull the lever up while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. Reclining To recline the seatback, pull the lever up and lean back. To bring the seatback forward again, pull the lever and move your body forward. The seatback moves forward.


SPA0097


SPA0099


Seat lifter (Driver’s seat) Turn either dial to adjust the angle and height of the seat cushion to the desired position.


2-13


Z 01.2.1/A32-D X


Forward and backward Moving the switch forward or backward will slide the seat forward or backward to the desired position. Reclining Move the recline switch backward until the desired angle is obtained. To bring the seat- back forward again, move the switch forward and move your body forward. The seatback will move forward.


POWER SUPPORT SEAT (If so equipped)


I Do not adjust the driver’s seat while driving in order that full attention may be given to the driving operations.


I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls.


SPA0098


Unattended children could become involved in serious accidents.


Operating tips I The motor has an auto-reset overload pro- tection circuit. the motor stops during operation, wait 30 seconds, then reactivate the switch.


If


I Do not operate the power support seat for a long period of time when the engine is off. This will discharge the battery.


2-14


Z 01.2.1/A32-D X


SPA0100


SPA0467


SPA0014


Seat lifter (Driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion.


Lumbar support (Driver’s seat) Turn the lever forward or backward to adjust the seat lumbar area.


HEAD RESTRAINT To raise the head restraint, just pull it up. To lower, push the lock knob and push the head restraint down.


Adjust the top of the head restraints level with the top of your ears.


Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjust-


2-15


Z 01.2.1/A32-D X


ment after someone else uses the seat.


are able to gain access to the trunk room.


SPA0102


REAR SEAT Center armrest and tray Pull the armrest forward and lay it horizontal. Then release the lever (inset) and pull the tray forward (If so equipped). In this condition you


2-16


Z 01.2.1/A32-D X


SUPPLEMENTAL RESTRAINT SYSTEM (SUPPLEMENTAL AIR BAG SYSTEM) This Supplemental Restraint System section contains important information concerning the driver and passenger supplemental air bags. The Supplemental Restraint System Air Bag can help reduce impact force to the driver and to the front passenger in certain frontal colli- sions. The supplemental air bags are designed to supplement the crash protection provided by the driver and passenger seat belts and are not a substitute for them. The seat belts should always be correctly worn and the driver and front passenger seated a suitable distance away from the steering wheel and instrument panel. (See “Seat belts” for instructions and precautions on seat belt usage.) After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.


SPA0504


SPA0505


I The supplemental air bags ordinarily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Al- ways wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.


I The seat belts and the supplemental air bags are most effective when you are sitting back and upright in the seat. Supplemental air bags inflate with great If you are unre- strained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the supplemental air bag if you are up


force.


2-17


Z 01.2.1/A32-D X


SPA0476


SPA0477


SPA0478


against it when it inflates. Always sit back against the seatback and as far away as practical from the steering wheel or instrument panel. Always use the seat belts.


I Keep hands on the outside of the steering wheel. Placing them inside the steering wheel rim could increase the risk that they are injured when the supplemental air bag inflates.


2-18


Z 01.2.1/A32-D X


SPA0479


SPA0480


SPA0482


I Never let children ride unrestrained. Do not attempt to hold them in your lap or arms. Some examples of dan- gerous riding positions are shown in the previous illustrations.


I Children may be severely injured or killed when the supplemental air bag inflates if they are not properly re- strained.


I Also, never install a rear-facing child restraint in the front seat. An inflating supplemental air bag could seriously injure or kill your child. See “Child restraints for infants and small chil- dren” for details.


SPA0481


SPA0483


2-19


Z 01.2.1/A32-D X


The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dashboard. Since the supplemental air bag inflates quickly in order to help protect the occupant, the force of the supplemental air bag inflating can increase the risk of injury if the occupant is too close to or is against the supplemental air bag module during inflation.


The supplemental air bag will deflate quickly after a collision. After turning the ignition key to the “ON” position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.


I Do not place any objects on the steer- ing wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steer- ing wheel or instrument panel. Such objects may become dangerous pro- jectiles and cause injury if the supple- mental air bag inflates.


I Right after inflation, several supple-


the steering wheel;


Supplemental air bag system The driver supplemental air bag is located in the center of the front passenger supplemental air bag is mounted in the dashboard above the glove box. The supplemental air bag system is designed to inflate in higher severity frontal collisions, al- though it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental air bag operation. When the supplemental air bag inflates, a fairly


SPA0103A


loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to intentionally inhale it, as it may cause irrita- tion and choking. Those with a history of breathing trouble should get fresh air promptly.


Supplemental air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the occupant. They can help save lives and reduce serious injuries. However, an inflating supplemental air bag may cause facial abrasions or other injuries. Supplemental air bags do not provide restraint to the lower body.


2-20


Z 01.2.1/A32-D X


I Work around and on the supplemen- tal air bag system should be done by an authorized NISSAN dealer. Instal- lation of electrical equipment should also be done by an authorized NISSAN dealer. The SRS wiring har- nesses should not be modified or disconnected. Unauthorized electri- cal test equipment and probing de- vices should not be used on the supplemental air bag system.


I The SRS wiring harnesses are cov- ered with yellow insulation either just before the harness connectors or for the complete harness, for easy identification.


When selling your vehicle, we request that you inform the buyer about the supplemental air bag system and guide the buyer to the appro- priate sections in this Owner’s Manual.


mental air bag system components will be hot. Do not touch them; you may severely burn yourself.


I No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or dam- age to the supplemental air bag sys- tem.


I Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the supplemental air bag system.


I Tampering with the supplemental air bag system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the dashboard, or by installing additional trim mate- rial around the supplemental air bag system.


2-21


Z 01.2.1/A32-D X


SUPPLEMENTAL AIR BAG WARNING LABELS


SUPPLEMENTAL AIR BAG WARNING LIGHT


Warning labels about the supplemental air bag system are placed in the vehicle.


SPA0104A


SPA0105


The supplemental air bag light, displaying “AIR BAG” in the instrument panel, monitors the circuits of the supplemental air bag. The cir- cuits monitored by the supplemental air bag light are the diagnosis sensor unit, supplemen- tal air bag modules and all related wiring. When the ignition key is in the “ON” or “START” position, the supplemental air bag light will illuminate for about 7 seconds and then turn off. This means the system is opera- tional.


2-22


Z 01.2.1/A32-D X


should be inspected by an authorized NISSAN dealer if there is any damage to the front end portion of the vehicle. I If you need to dispose of a supple- mental air bag or scrap the vehicle, contact an authorized NISSAN dealer. Correct supplemental air bag dis- posal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.


If any of the following conditions occurs, the supplemental air bag needs servicing:


1. The supplemental air bag light goes off


within 7 seconds.


2. The supplemental air bag light flashes in- termittently or remains on (after 7 seconds).


3. The supplemental air bag light does not


come on at all.


Under these conditions, the Supplemental Re- straint System Air Bag may not operate prop- erly. It must be checked and repaired.


Take your vehicle to the nearest authorized NISSAN dealer.


inflation has occurred. Repair and replace- ment of the supplemental air bag system should be done only by authorized NISSAN dealers. To ensure long-term functioning, the sys- tem must be inspected 10 years after the date of manufacture noted on the certifica- tion label located on the driver side center pillar.


When maintenance work is required on the vehicle, the supplemental air bag system and related parts should be pointed out to the person conducting the maintenance. The igni- tion key should always be in the “LOCK” position when working under the hood or in- side the vehicle.


If the supplemental air bag warning light is on, it could mean that the supplemen- tal air bag will not operate in an accident.


Repair and replacement procedure The supplemental air bag system is designed to inflate on a one-time-only basis. As a re- minder, unless it is damaged, the supplemen- tal air bag light will remain illuminated after


I Once the supplemental air bag has inflated, the supplemental air bag module will not function again and must be replaced. The supplemental air bag module should be replaced by an authorized NISSAN dealer. The supplemental air bag module cannot be repaired.


I The supplemental air bag system


2-23


Z 01.2.1/A32-D X


SEAT BELTS


PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted. NISSAN strongly encourages you and all of your pas- sengers to buckle up every time you drive, even if your seating position includes a supple- mental air bag. Some states, provinces or territories re- quire that seat belts be worn at all times when a vehicle is being driven.


SPA0506


SPA0485


I Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained and, in a child restraint.


if appropriate,


I The belt should be adjusted properly and to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the


2-24


chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.


I Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your backs under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder.


I Position the lap belt as low and snug


Z 01.2.1/A32-D X


I Never carry more people in the ve-


hicle than there are seat belts.


I If the seat belt warning lamp glows continuously while the ignition is turned “ON” with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by your NISSAN dealer.


I All seat belt assemblies including re- tractors and attaching hardware should be inspected by your NISSAN dealer after any collision. NISSAN recommends that all seat belt assem- blies in use during a collision be replaced unless the collision was mi- nor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use dur- ing a collision should also be in- spected and replaced if either dam- age or improper operation is noted.


CHILD SAFETY Children need adults to help protect them.


Infants and children need special pro- tection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints.


All U.S. states and provinces of Canada re- quire the use of approved child restraints for infants and small children. (See “Child re- straints for infants and small children” later in this section.)


In addition, there are many types of child restraints available for larger children which should be used for maximum protection. Infant or small child NISSAN recommends that infants or small children be placed in child restraints that com- ply with Federal Motor Vehicle Safety Stan- dards or Canadian Motor Vehicle Safety Stan- dards. You should choose a child restraint that fits your vehicle and always follow the manu-


2-25


Z 01.2.1/A32-D X


SPA0486


as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident.


I Be sure the seat belt tongue is se- curely fastened to the proper buckle. I Do not wear the belt inside out or twisted. Doing so may reduce its ef- fectiveness.


I Do not allow more than one person to


use the same belt.


facturer’s instructions for installation and use. Children Children who are too large for child restraint systems should be seated and restrained by the seat belts which are provided. NISSAN recommends that children sit in the rear seat if possible. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.


the shoulder belt


Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident.


PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. Contact your doctor for specific recommendations. The lap belt should be worn snug and positioned as low as possible around the hips, not the waist. INJURED PERSONS NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recommendations.


3-POINT TYPE SEAT BELT WITH RETRACTOR


SPA0492


Every person who drives or rides in this vehicle should wear a seat belt at all times.


Fastening the belts 1. Adjust the seat.


2-26


Z 01.2.1/A32-D X


and adjust the seat belt properly.


SPA0493


Do not ride in a moving vehicle when the seatback is reclined. This can be dan- gerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive se- rious internal injuries.


For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat


PD1024M


2. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps.


The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion will permit the belt to move, and allow you some freedom of movement in the seat. 3. Position the lap belt portion low and snug


on the hips as shown.


4. Pull the shoulder belt portion toward the


retractor to take up extra slack.


The front passenger side seat belt and rear


2-27


Z 01.2.1/A32-D X


3-point seat belts have a cinching mechanism for child seat installation. It is referred to as the automatic locking mode. When the cinching mechanism is activated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted. Refer to “Child restraints for infants and small children” later in this section for more information. The automatic locking mode should be used only for child seat installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. Unfastening the belts To unfasten the belt, press the button on the buckle. The seat belt will automatically retract.


Checking seat belt operation (3-point type with retractor) Your seat belt retractors are designed to lock belt movement using two separate methods: 1) When the belt is pulled quickly from the


retractor.


2) When the vehicle slows down rapidly. You can check their operation as follows: I Grasp the shoulder belt and pull quickly forward. The retractor should lock and re- strict further belt movement.


If the retractor does not lock during this check or if you have any questions about belt opera- tion, see your NISSAN dealer.


PD1321-A


Shoulder belt height adjustment (For front seats) The shoulder belt anchor height should be adjusted to the position best for you. (See “Precautions on seat belt usage”.) To adjust, squeeze the release buttons, and then move it to the desired position, so that the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off of your shoulder.


2-28


Z 01.2.1/A32-D X


After adjustment, release the button and check that it does not move up and down to make sure the shoulder belt anchor is securely fixed in position.


SPA0281


SPA0278


2-POINT TYPE WITHOUT RETRACTOR (center position of rear seat) Selecting correct set of belts The center seat belt buckle and tongue are identified by the CENTER mark. The center seat belt tongue can be fastened only into the center seat belt buckle.


Fastening the belts 1. Insert the tongue into the buckle marked


CENTER until it snaps.


2-29


Z 01.2.1/A32-D X


SPA0469


SPA0280


2. To lengthen, hold the tongue at a right angle to the belt and pull on the belt. To shorten, pull the end of the belt attached to the belt clip away from the tongue, and then pull the belt clip to take up the slack.


3. Position the lap belt low and snug on the


hips as illustrated.


Unfastening the belts To unfasten the belt, press the button on the buckle.


SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The extender adds approximately 8 inches (200
mm) of length and may be used for either the driver or front passenger seating position. See your NISSAN dealer for assistance if the ex- tender is required.


I Only NISSAN belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN belts.


I Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.


2-30


Z 01.2.1/A32-D X


SEAT BELT MAINTENANCE I To clean the seat belt webbings, apply a mild soap solution or any solution recom- mended for cleaning upholstery or carpets. Then brush the webbing, wipe it with a cloth and allow it to dry in the shade. Do not allow the seat belts to retract until they are com- pletely dry.


I If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.


I Periodically check to see that the seat belt and the metal components such as buckles, tongues, retractors, flexible wires and anchors work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire belt assembly should be replaced.


CHILD RESTRAINTS FOR INFANTS AND SMALL CHILDREN


I Infants and small children should al- ways be placed in an appropriate child restraint while riding in the ve- hicle. Failure to use a child restraint can result in serious injury or death. I Children and infants should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


I Nissan recommends that the child restraint be installed in the rear seat. According to accident statistics, chil- dren are safer when properly re- strained in the rear seat than in the front seat.


I An improperly installed child re- straint could lead to serious injury or death in an accident.


In general, child restraints are designed to be


2-31


installed with a lap belt or the lap portion of a three-point type seat belt. Child restraints specially designed for infants and small children are offered by several manufacturers. When selecting any child re- straint, keep the following points in mind:


1) Choose only a restraint with a label certify- ing that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.


2) Check that child restraint in your vehicle to be sure it is compatible with the vehicle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recom- mended practice J1819 for child restraint installation.


3) If the child restraint is compatible with your vehicle, place your child in the child re- straint and check the various adjustments to be sure the child restraint is compatible with your child. Always follow all recom- mended procedures.


All U.S. states and provinces of Canada require that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper- ated.


Z 01.2.1/A32-D X


Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.


tioned to fit the child restraint, but as upright as possible.


I After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.


I For a front facing child restraint, if the seat position where it is installed has a 3-point type lap/shoulder belt, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint.


I When your child restraint is not in use, keep it secured with a seat belt to prevent from being thrown around in case of a sudden stop or accident.


it


I Never install a rear-facing child re- straint in the front seat. An inflating supplemental air bag could seriously injure or kill your child. A rear-facing child restraint must only be used in the rear seat. See “Installation on front passenger seat” for details.


I Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.


I Follow all of the child restraint manu- facturer’s instructions for installation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.


I If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.


I Adjustable seatbacks should be posi-


2-32


Z 01.2.1/A32-D X


facturer’s instructions for belt routing.


3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.


4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.


5. If it is not secure, try to tighten the belt again, or put the restraint in another seat. 6. Check to make sure the child restraint is


properly secured prior to each use.


PD1174


2-33


Z 01.2.1/A32-D X


SPA0276


Installation on rear center seating position When you install a child restraint in a rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. It can be placed in a front facing or rear facing direction, depending on the size of the child. Always follow the restraint manufacturer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu-


in a sudden stop or collision.


When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing or rear facing direction, depending on the size of the child. Always follow the restraint manufac- turer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). It will revert back to “emergency locking” when the belt is fully retracted.


4. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates that the retractor is in the auto- matic locking mode. Pull up on the belt


Installation on rear outboard seating positions


PD1331


I The 3-point belt on your vehicle is equipped with a locking mode retrac- tor which must be used when install- ing a child restraint.


I Failure to do so will result in the child restraint not being properly secured. It could tip over or otherwise be un- secured and cause injury to the child


PD1332


to remove any slack in the belt.


5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.


6. Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the belt is in the automatic locking mode.


7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.


2-34


Z 01.2.1/A32-D X


After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and will only lock during a sudden stop or impact.


Bolt length: more than 1.18 in (30 mm) Thread pitch: 1.25 mm


The top strap should be secured to the attach- ing bolt which provides the straightest installa- tion of the top strap.


Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


APD0107


Top strap child restraint If your child restraint has a top strap, install the anchor bracket to the provided anchor point. The top strap anchor bracket is available through your NISSAN dealer.


Part No. 88894-89900


Secure the child restraint with the center lap belt or the lap portion of an outboard 3-point belt and latch the top strap hook onto the appropriate anchor bracket. To install the an- chor bracket, a metric bolt of the dimensions listed below must be used. Bolt diameter: 8.0 mm 2-35


Z 01.2.1/A32-D X


are pre-cut circles at each anchor point location that should break away from the shelf support material when pressure is applied to them. Remove the bolt after you feel the pre-cut circle separate from the shelf support material.


2. Cut a small slit through the parcel shelf fabric at the anchor point location. Reach through the fabric with a tool such as a pair of needle-nose pliers and remove the pre- cut circle in the parcel shelf support mate- rial.


SPA0117


3. Install the bolt through the top strap hook


and into the anchor point nut.


4. Be sure to follow all of the instructions that accompany the top strap attaching hard- ware.


Your NISSAN dealer can assist you with the installation of your child restraint.


Anchor point locations Anchor points are located under the rear par- cel shelf finisher.


To use attaching hardware for child restraints with top straps, follow these instructions care- fully:


1. Open the trunk and find the anchor point nuts on the under side of the rear parcel shelf. Thread a bolt (8.0 mm diameter, 1.25
pitch) up through the nut behind the seating position where the child restraint will be installed and use it to break through the rear parcel shelf support material. There


2-36


Z 01.2.1/A32-D X


I Failure to use the retractor’s locking mode may result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.


When you install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a front-facing direction only. Move the seat as far back from the instrument panel as possible. Always follow the child restraint instructions. Child re- manufacturer’s straints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage.


SPA0487


SPA0483


Installation on front passenger seat


I Never install a rear-facing child re- straint in the front passenger seat. Supplemental air bags inflate with great force. A rear-facing child re- straint could be struck by the supple- mental air bag in a crash and could seriously injure or kill your child.


I If you install a front-facing child re- straint in the front passenger seat, place the passenger seat as far back as possible.


I A child restraint with a top strap should not be used in the front pas- senger seat.


I The 3-point belt in your vehicle is equipped with a locking mode retrac- tor which must be used when install- ing a child restraint.


2-37


Z 01.2.1/A32-D X


Loading...
x