Download PDF Manual

in this section for proper use and installation.)


If the front passenger seat is not occupied, the passenger air bag is designed not to inflate in a crash. However, heavy objects placed on the seat could result in air bag inflation, because of the object being detected by the occupant classification sensors. Other conditions could also result in air bag inflation, such as if a child is standing on the seat, or if two children are on the seat, contrary to the instructions in this manual. Always be sure that you and all vehicle occupants are seated and restrained properly.


Using the passenger air bag status light, you can monitor when the front passenger air bag is automatically turned OFF with the seat occu- pied. The light will not illuminate when the front passenger seat is unoccupied.


that the person is a small adult, or is not sitting on the seat properly.


is not


If a child restraint must be used in the front seat, the passenger air bag status light may or may not be illuminated, depending on the size of the child and the type of child restraint being used. If the air bag status light illuminated (indicating that the air bag might inflate in a crash), it could be that the child restraint or seat belt is not being used properly. Make sure that the child restraint is installed properly, the seat belt is positioned properly. If the air bag status light is not illuminated, reposition the occupant or child restraint in a rear seat.


is used properly and the occupant


If the passenger air bag status light will not illuminate even though you believe that the child restraint, the seat belts and the occupant are properly positioned, the system may be sensing an unoccupied seat (in which case the air bag is OFF). Your NISSAN dealer can check that the system is OFF by using a special tool. However, until you have confirmed with your dealer that your air bag is working properly, reposition the occupant or child restraint in a rear seat.


The air bag system and passenger air bag status light will take a few seconds to register a change in the passenger seat status. However, if the seat becomes unoccupied, the air bag status light will remain off.


is in the seat but


the If an adult occupant passenger air bag status light is illuminated (indicating that the air bag is OFF), it could be 1-50 Safety — Seats, seat belts and supplemental restraint system


Black plate (64,1)


If a malfunction occurs in the front passenger air bag system, the supplemental air bag warning , located in the meter and gauges area, light will blink. Have the system checked by a NISSAN dealer.


Other supplemental front-impact air bag precautions


WARNING


. Do not place any objects on the steering wheel pad or on the instru- ment panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause injury if the front air bags inflate.


. Do not place objects with sharp edges on the seat. Also, do not place heavy objects on the seat that will leave permanent impressions in the seat. Such objects can damage the seat or occupant classification sensors (weight sensors). This can affect the operation of the air bag system and result in serious perso- nal injury.


. Do not use water or acidic cleaners


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (65,1)


trical equipment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring harnesses* should not be modified or disconnected. Un- authorized electrical test equipment and probing devices should not be used on the air bag system.


. A cracked windshield should be replaced immediately by a qualified repair facility. A cracked windshield could affect the function of the supplemental air bag system.


*The SRS wiring harness connectors are yellow and orange for easy identification.


When selling your vehicle, we request that you inform the buyer about the front air bag system and guide the buyer to the appropriate sections in this Owner’s Manual.


(hot steam cleaners) on the seat. This can damage the seat or occu- pant classification sensors. This can also affect the operation of the air bag system and result in serious personal injury.


Immediately after inflation, several front air bag system components will be hot. Do not touch them; you may severely burn yourself.


. No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental infla- tion of the supplemental air bag or damage to the supplemental air bag system.


. Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the front air bag sys- tem.


Tampering with the front air bag system may result in serious perso- nal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by


placing material over the steering wheel pad and above the instrument panel or by installing additional trim material around the air bag system. . Modifying or tampering with the front passenger seat may result in serious personal injury. For exam- ple, do not change the front seats by placing material on the seat cushion or by installing additional trim ma- terial, such as seat covers, on the seat that is not specifically designed to assure proper air bag operation. Additionally, do not stow any ob- jects under the front passenger seat or the seat cushion and seatback. Such objects may interfere with the proper operation of the occupant classification sensors.


. No unauthorized changes should be made to any components or wiring of the seat belt system. This may affect the front air bag system. Tampering with the seat belt system may result in serious personal in- jury.


. Work on and around the front air bag system should be done by a NISSAN dealer. Installation of elec-


Safety — Seats, seat belts and supplemental restraint system 1-51


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (66,1)


collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions on the side where the vehicle is impacted.


Vehicle damage (or lack of it) is not always an indication of proper side air bag and curtain air bag operation.


When the side air bags and curtain air bags inflate, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.


Side air bags, along with the use of seat belts, help to cushion the impact force on the chest and pelvic area of the front occupants. Curtain air bags help to cushion the impact force to the head of occupants in the front and rear outboard seating positions. They can help save lives and reduce serious injuries. However, side air bags and curtain air bags may cause abrasions or other injuries. Side air bags and curtain air bags do not provide restraint to the lower body.


The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the side air bags. Rear seat


to help protect


passengers should be seated as far away as practical from the door finishers and side roof rails. The side air bags and curtain air bags inflate quickly in order the occupants in the outboard seating positions. Because of this, the force of the side air bags and curtain air bags inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation. The side air bags and curtain air bags will deflate quickly after the collision is over.


The side air bags and curtain air bags operate only when the ignition switch is in the ON position.


After turning the ignition switch to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the systems are operational.


WARNING


. Do not place any objects near the seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates.


SSS0978


FRONT SEAT-MOUNTED SIDE-IM- PACT SUPPLEMENTAL AIR BAG AND ROOF-MOUNTED CURTAIN SIDE-IM- PACT SUPPLEMENTAL AIR BAG SYS- TEMS


The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails. These systems are designed to meet voluntary guide- lines to help reduce the risk of injury to out-of- position occupants. However, all of the information, cautions and warnings in this manual still apply and must be followed. The side air bags and curtain air bags are designed to inflate in higher severity side


1-52 Safety — Seats, seat belts and supplemental restraint system


Model "Z12-D" EDITED: 2010/ 9/ 27


be done by a NISSAN dealer. In- stallation of electrical equipment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring harnesses* should not be modified or discon- nected. Unauthorized electrical test equipment and probing devices should not be used on the side air bag and curtain supplemental air bag systems.


*The SRS wiring harness connectors are yellow and orange for easy identification.


When selling your vehicle, we request that you inform the buyer about the side air bag and curtain air bag systems and guide the buyer to the appropriate sections in this Owner’s Manual.


. Right after inflation, several side air bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself.


. No unauthorized changes should be made to any components or wiring of the side air bag and curtain air bag systems. This is to prevent damage to or accidental inflation of the side air bag and curtain air bag systems.


. Do not make unauthorized changes to your vehicle’s electrical system, suspension system or side panel. This could affect proper operation of the side air bag and curtain air bag systems.


Tampering with the side air bag system may result in serious perso- nal injury. For example, do not change the front seats by placing material near the seatbacks or by installing additional trim material, such as seat covers, around the side air bag.


. Work around and on the side air bag and curtain air bag systems should


Black plate (67,1)


SEAT BELTS WITH PRETENSIONERS (front seats)


WARNING


The pretensioners cannot be reused after activation. They must be re- placed together with the retractor and buckle as a unit.


If the vehicle becomes involved in a collision but a pretensioner is not activated, be sure to have the pre- tensioner system checked and, if necessary, replaced by a NISSAN dealer.


. No unauthorized changes should be made to any components or wiring of the pretensioner system. This is to prevent damage to or accidental activation of the pretensioners. Tampering with the pretensioner system may result in serious perso- nal injury.


. Work around and on the preten- sioner system should be done by a NISSAN dealer. Installation of elec- trical equipment should also be done by a NISSAN dealer. Un- authorized electrical test equipment


Safety — Seats, seat belts and supplemental restraint system 1-53


Model "Z12-D" EDITED: 2010/ 9/ 27


reduce forces against the chest.


The supplemental air bag warning light is used to indicate malfunctions in the pretensioner system. (See “SUPPLEMENTAL AIR BAG WARNING LIGHT” later in this section for more details.) If the operation of the supplemental air bag warning light indicates there is a malfunc- tion, have the system checked by a NISSAN dealer.


When selling your vehicle, we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections in this Owner’s Manual.


and probing devices should not be used on the pretensioner system.


If you need to dispose of a preten- sioner or scrap the vehicle, contact a NISSAN dealer. Correct preten- sioner disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.


The pretensioner system may activate with the supplemental air bag system in certain types of collisions. Working with the seat belt retractor, it helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants.


The pretensioner is encased with the seat belt retractor. These seat belts are used the same way as conventional seat belts.


When a pretensioner activates, smoke is re- leased and a loud noise may be heard. The smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.


After pretensioner activation, load limiters allow the seat belt to release webbing (if necessary) to


1-54 Safety — Seats, seat belts and supplemental restraint system


Black plate (68,1)


SSS1020


SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front- impact air bag system are placed in the vehicle as shown in the illustration. *1 SRS air bag The warning labels are located on the surface of the sun visors.


Model "Z12-D" EDITED: 2010/ 9/ 27


the supplemental air bag warning light illumi- nates for about 7 seconds and then turns off. This means the system is operational.


If any of the following conditions occur, the front air bag, side air bag, curtain air bag and pretensioner systems need servicing:


The supplemental air bag warning light remains on after approximately 7 seconds.


The supplemental air bag warning light flashes intermittently.


The supplemental air bag warning light does not come on at all.


Under these conditions, the front air bag, side air bag, curtain air bag and pretensioner systems may not operate properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer.


Black plate (69,1)


WARNING


If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.


REPAIR AND REPLACEMENT PRO- CEDURE The front air bags, side air bags, curtain air bags and pretensioners are designed to activate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light will remain illuminated after inflation has oc- curred. Repair and replacement of these sys- tems should be done only by a NISSAN dealer.


When maintenance work is required on the vehicle, the front air bags, side air bags, curtain air bags and pretensioners and related parts should be pointed out to the person performing the maintenance. The ignition switch should always be in the LOCK position when working under the hood or inside the vehicle.


Safety — Seats, seat belts and supplemental restraint system 1-55


Model "Z12-D" EDITED: 2010/ 9/ 27


SPA1097


SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light, display- in the instrument panel, monitors the ing circuits of the supplemental front-impact air bag, front seat-mounted side-impact supplemental air bag, roof-mounted curtain side-impact sup- plemental air bag and seat belt pretensioner systems. The monitored circuits include Air bag Control Unit (ACU), crash zone sensor, satellite sensors, occupant classification system, front air bag modules, side air bag modules, curtain air bag modules, pretensioners and all related wiring.


When the ignition switch is in the ON position,


Black plate (70,1)


WARNING


. Once a front air bag, side air bag or curtain air bag has inflated, the air bag module will not function again and must be replaced. Additionally, the activated pretensioners must also be replaced. The air bag mod- ule and pretensioner should be replaced by a NISSAN dealer. The air bag modules and pretensioner system cannot be repaired.


The front air bag, side air bag and curtain air bag systems, and preten- sioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle.


If you need to dispose of a supple- mental air bag or pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct supplemental air bag and pretensioner system dis- posal procedures are set forth in the appropriate NISSAN Service Man- ual. Incorrect disposal procedures could cause personal injury.


1-56 Safety — Seats, seat belts and supplemental restraint system


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (7,1)


2 Instruments and controls


Cockpit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Instrument panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Meters and gauges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . 2-6
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Vehicle information display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Outside air temperature (if so equipped). . . . . . . . . . . . . . 2-8
Continuously Variable Transmission (CVT) position indicator (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 2-8
Trip computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Warning/indicator lights and audible reminders . . . . . . . 2-11
Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Indicator lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Security systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Vehicle Security System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
NISSAN Vehicle Immobilizer System . . . . . . . . . . . . . . . . . 2-20
Windshield wiper and washer switch . . . . . . . . . . . . . . . . . . . . 2-21
Rear window wiper and washer switch. . . . . . . . . . . . . . . . . . 2-23
Rear window and outside mirror defroster switch. . . . . 2-24
Headlight and turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Headlight switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24


Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Fog light switch (if so equipped). . . . . . . . . . . . . . . . . . . . . . 2-28
Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Vehicle Dynamic Control (VDC) OFF switch . . . . . . . . . . . 2-29
Heated seats (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Clock (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Adjusting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Resetting the time (Type B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Cup holders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Rear pillar pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Luggage hooks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Utility hooks (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
Interior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
Map lights (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
Map light control switch (if so equipped) . . . . . . . . . . . 2-41
Ceiling light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Cargo light (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42


Model "Z12-D" EDITED: 2010/ 9/ 27


COCKPIT


Black plate (74,1)


10. Steering-wheel-mounted controls (right side)*


— Cruise control switches* 11. Selector lever or Shift lever


— Continuously Variable Transmission (CVT) — Manual Transmission (MT)


12. Parking brake *: if so equipped


Front cup holders


1. 2. Headlight, fog light and turn signal switch 3. Steering wheel


— Horn — Driver’s supplemental air bag


4. Wiper and washer switch 5. 2-2 Instruments and controls


Fuse box cover


SSI0563


6. Outside mirror remote control switch 7. Vehicle Dynamic Control (VDC) OFF switch 8. 9. Steering-wheel-mounted controls (left side)*


Tilting steering wheel lever


— Audio control* — Bluetooth® Hands-Free Phone System control*


Model "Z12-D" EDITED: 2010/ 9/ 27


INSTRUMENT PANEL


1. Side ventilator 2. Meters and gauges 3. Center ventilator 4. Hazard warning flasher switch 5. Audio system*


— Clock*


Black plate (75,1)


11. Push-button ignition switch (models with Intelli-


gent Key system)


12. Heater and air conditioner* control


— Rear window and outside mirror* defroster switch


iPod® connector*/USB connector*


13. Utility hooks* 14. Heated seat switch* 15. 16. Power outlet 17. Glove box *:


if so equipped


SSI0840


Front passenger air bag status light Front passenger supplemental air bag Fuel-filler door release handle


6. 7. 8. 9. Hood release handle 10.


Ignition switch (models without system)


Intelligent Key


Instruments and controls 2-3


Model "Z12-D" EDITED: 2010/ 9/ 27


METERS AND GAUGES


Black plate (76,1)


if so equipped


*: The needle indicators may move slightly after the ignition switch is placed in the OFF or LOCK position. This is not a malfunction.


Tachometer


1. 2. Engine coolant temperature gauge 3. Vehicle information display


— Odometer/twin trip odometer — Trip computer — Outside air temperature* Fuel gauge


4.


2-4 Instruments and controls


SIC4119


5. Speedometer 6. Warning/indicator lights 7. 8. Continuously Variable Transmission (CVT) posi-


Instrument brightness control knob


tion indicator*


9. RESET switch for trip odometer/Trip computer


mode switch


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (77,1)


For trip computer information, see “TRIP COM- PUTER” later in this section.


Resetting the trip odometer: Pushing the reset switch *3
second resets the trip odometer to zero.


for approximately 1


Instruments and controls 2-5


Model "Z12-D" EDITED: 2010/ 9/ 27


SIC4120


SIC4121


Speedometer


SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h).


Odometer/twin trip odometer


Odometer/twin trip odometer The odometer *1 /twin trip odometer *2
are displayed when the ignition switch is in the ON position.


The odometer records the total distance the vehicle has been driven.


The twin trip odometer records the distance of individual trips.


Changing the display: Pushing the reset switch *3
meter panel changes the display as follows: TRIP A ? TRIP B ? Trip computer mode ? TRIP A


located on the


Black plate (78,1)


SIC4712


SIC4122


SIC4123


Loose fuel cap warning message Push the trip computer mode switch *A for more than 1 second to reset the LOOSE FUEL CAP warning message after the fuel cap has been tightened. For additional information see “FUEL-FILLER CAP” in the “3. Pre-driving checks and adjustments” section of this manual.


TACHOMETER The tachometer indicates engine speed in revolutions per minute (RPM). Do not rev the engine into the red zone *1 .


ENGINE COOLANT TEMPERATURE GAUGE The gauge *1
temperature.


indicates the engine coolant


CAUTION


When engine speed approaches the red zone, shift to a higher gear or reduce engine speed. Operating the engine in the red zone may cause serious engine damage.


The engine coolant temperature is within the normal range when the gauge is within the zone *2


shown in the illustration.


The engine coolant temperature varies with the outside air temperature and driving conditions.


2-6 Instruments and controls


Model "Z12-D" EDITED: 2010/ 9/ 27


CAUTION


If the gauge indicates engine coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the en- gine. See “IF YOUR VEHICLE OVER- HEATS” in the “6. In case of emergency” section for immediate action required.


SIC4124


FUEL GAUGE The gauge *1
level in the tank.


indicates the approximate fuel


The gauge may move slightly during braking, turning, acceleration, or going up or down hills.


Refill the fuel tank before the gauge registers 0 (empty).


The low fuel warning light illuminates when the amount of fuel in the tank is getting low. Refuel as soon as it is convenient, preferably before the gauge reaches 0. There will be a small reserve of fuel in the tank when the fuel gauge reaches 0.


Black plate (79,1)


indicates that the fuel-filler door is The located on the front passenger’s side of the vehicle.


CAUTION


malfunction indicator


If the vehicle runs out of fuel, the light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.


. For additional


information, see “Malfunction Indicator Light (MIL)” later in this section.


Instruments and controls 2-7


Model "Z12-D" EDITED: 2010/ 9/ 27


When the outside air temperature becomes 378F (38C) or lower, the outside air temperature display blinks to give a warning. The display will stop blinking after 1 minute or when the outside air temperature becomes 398F (48C) or above.


The display may differ from the actual outside temperature displayed on various signs or bill- boards.


CONTINUOUSLY VARIABLE TRANS- MISSION (CVT) POSITION INDICATOR (if so equipped) The Continuously Variable Transmission (CVT) position indicator indicates the selector lever position when the ignition switch is in the ON position.


SIC4125


VEHICLE INFORMATION DISPLAY When the ignition switch is placed in the ON position, the vehicle information display shows the following information:


1. Outside air temperature (if so equipped) 2. Continuously Variable Transmission (CVT) posi-


tion indicator (if so equipped)


Twin trip odometer/Trip computer


3. Odometer/Instrument brightness control display 4. OUTSIDE AIR TEMPERATURE (if so equipped) The outside air temperature is displayed in 8F or 8C.


2-8 Instruments and controls


Black plate (80,1)


SIC4126


TRIP COMPUTER The switch for the trip computer is located on the meter panel.


When the ignition switch is placed in the ON position, modes of the trip computer can be selected by pushing the trip computer mode switch *A . Each time the trip computer mode switch *A is pushed, the display will change as follows: (TRIP A ? TRIP B) ? Current fuel consumption ? Distance to empty (dte) ? Average fuel consumption ? Average speed ? Elapsed time (Canada only) ? Maintenance information (Canada only) (? TRIP A)


Model "Z12-D" EDITED: 2010/ 9/ 27


Current fuel consumption The current fuel consumption mode shows the current fuel consumption.


Distance to empty (dte — mls or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.


The display is updated every 30 seconds.


The dte mode includes a low range warning feature. When the fuel level is low, the dte mode is automatically selected and the dte display will blink. Push the trip computer mode switch *A to return to the mode that was selected before the warning occurred.


level drops even lower, the dte


When the fuel display will change to “----”.


If the amount of fuel added is small, the display just before the ignition switch is turned off may continue to be displayed.


. When driving uphill or rounding curves, the fuel in the tank shifts, which may momenta- rily change the display.


Black plate (81,1)


Average fuel consumption (mpg or l (liter)/100 km) The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pushing the trip computer mode switch *A for approximately 1 second. The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “---”.


Average speed (mph or km/h) The average speed mode shows the average vehicle speed since the last reset. Resetting is done by pushing the trip computer mode switch *A for approximately 1 second. The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “---”.


Elapsed time (Canada only) The elapsed time mode shows the time since the last reset. The displayed time can be reset by pushing the trip computer mode switch *A for approximately 1 second.


Resetting displays When the average fuel consumption, average speed, elapsed time or TRIP B is displayed, push the trip computer mode switch *A for than 3 seconds. The average fuel longer


consumption, average speed, elapsed time and trip odometer (TRIP B only) displays will be reset at the same time.


Maintenance information (Canada only) When the ignition switch is placed in the ON position, maintenance information (the wrench and distance to change a main- symbol tenance item) comes on for about 5 seconds and then turns off.


The wrench symbol appears when the set distance comes for changing an item, such as engine oil.


To set the distance to change an item:


1. Place the ignition switch in the ON position. Push the trip computer mode switch *A for 3 seconds while the wrench symbol and maintenance information are displayed. The symbol and distance display will start flashing and the display shows the current interval.


2. Push the switch *A to increase the interval


distance.


Each step increases the interval distance by 500 miles (1,000 km). The interval distance can be set up to 18,000 miles (30,000 km) after the display returns to 0 (zero).


3.


If no further action is made,


the display


Instruments and controls 2-9


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (82,1)


returns to the previous mode and the new interval is set.


If the interval distance is set to 0, the display will skip the maintenance information when the ignition switch is placed in the ON position.


2-10 Instruments and controls


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (83,1)


WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS


Anti-lock Braking System (ABS) warning light


Low fuel warning light


High beam indicator light


Low tire pressure warning light


Malfunction Indicator Light (MIL)


Brake warning light


Low washer fluid warning light*


Overdrive off indicator light*


P position selecting warning light*


Security indicator light


Charge warning light


Seat belt warning light


Vehicle Dynamic Control (VDC) warning light


Door open warning light


Supplemental air bag warning light


Low beam indicator light


Electric power steering warning light


Front passenger air bag status light


Turn signal/hazard indicator lights


Engine oil pressure warning light


Cruise indicator light*


Vehicle Dynamic Control (VDC) off indicator light


Intelligent Key system warning light*


Engine start operation indicator light*


*: if so equipped


CHECKING BULBS With all doors closed, apply the parking brake and place the ignition switch in the ON position without starting the engine. The following lights will come on:


or


The following lights come on briefly and then go


off (if so equipped):


or


If any light does not come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system checked by a NISSAN dealer.


WARNING LIGHTS


or


Anti-lock Braking System (ABS) warning light


When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates


Instruments and controls 2-11


Model "Z12-D" EDITED: 2010/ 9/ 27


the ABS is operational.


If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer.


If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assis- tance. (See “BRAKE SYSTEM” in the “5. Starting and driving” section.)


or


Brake warning light


This light functions for both the parking brake and the foot brake systems.


Parking brake indicator:


When the ignition switch is in the ON position, the light illuminates when the parking brake is applied.


Low brake fluid warning light:


When the ignition switch is in the ON position, the light warns of a low brake fluid level. If the light illuminates while the engine is running with the parking brake not applied, stop the vehicle and perform the following:


1. Check the brake fluid level. If brake fluid is necessary, add fluid and have the system checked by a NISSAN dealer. (See “BRAKE


2-12 Instruments and controls


AND CLUTCH FLUID” in the “8. Mainte- nance and do-it-yourself” section.)


2.


If the brake fluid level is correct, have the warning system checked by a NISSAN dealer.


Anti-lock Braking System (ABS) warning indicator:


When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate the ABS is not functioning properly. Have the brake system checked, and if necessary re- paired, by a NISSAN dealer promptly. (See “Anti-lock Braking System (ABS) warning light” earlier in this section.)


WARNING


. Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.


. Pressing the brake pedal with the engine stopped and/or low brake


Black plate (84,1)


fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel.


If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.


Charge warning light


If the light illuminates while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see a NISSAN dealer immediately.


CAUTION


Do not continue driving if the alternator belt is loose, broken or missing.


Door open warning light


This light illuminates when any of the doors and/ or back door are not closed securely while the ignition switch is in the ON position.


Model "Z12-D" EDITED: 2010/ 9/ 27


Electric power steering warning light


When the ignition switch is in the ON position, the electric power steering warning light illumi- nates. After starting the engine, the electric power steering warning light turns off. This indicates the electric power steering system is operational.


the electric power steering warning light If illuminates while the engine is running, it may indicate the electric power steering system is not functioning properly and may need servicing. Have the electric power steering system checked by a NISSAN dealer.


When the electric power steering warning light illuminates with the engine running, the power assist to the steering will cease operation but you will still have control of the vehicle. At this time, greater steering efforts are required to operate the steering wheel, especially in sharp turns and at low speeds.


See “ELECTRIC POWER STEERING SYS- TEM” in the “5. Starting and driving” section.


Engine oil pressure warning light


This light warns of low engine oil pressure. If the light flickers or illuminates during normal driving,


pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.


The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. (See “ENGINE OIL” in the “8. Maintenance and do-it- yourself” section.)


CAUTION


Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so.


Intelligent Key system warning light (if so equipped)


After the ignition switch is placed in the ON position, this light comes on for about 2 seconds and then turns off.


This light illuminates or blinks as follows:


The light blinks in yellow when the door is closed with the Intelligent Key left outside the vehicle and the ignition switch in the ACC or ON position. Make sure that the


Black plate (85,1)


Intelligent Key is inside the vehicle.


The light blinks in green when the Intelligent Key battery is running out of power. Replace the battery with a new one. (See “KEY BATTERY REPLACEMENT” in the “8. Main- tenance and do-it-yourself” section.)


The light illuminates in yellow when it warns of a malfunction with the electrical steering lock system (if so equipped) or the Intelli- gent Key system.


If the warning light illuminates in yellow while the engine is stopped, it may be impossible to free the steering lock (if so equipped) or to start the engine. If the light comes on while the engine is running, you can drive the vehicle. However in these cases, contact a NISSAN dealer for repair as soon as possible.


Low fuel warning light


This light illuminates when the fuel in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the 0
(empty) position.


There will be a small reserve of fuel remaining in the tank when the fuel gauge reaches the 0 position.


Instruments and controls 2-13


Model "Z12-D" EDITED: 2010/ 9/ 27


Low tire pressure warning light


Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare.


The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly.


After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off.


Low tire pressure warning:


the vehicle is being driven with low tire


If pressure, the warning light will illuminate.


When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.


For additional information, see “TIRE PRES- SURE MONITORING SYSTEM (TPMS)” in the


2-14 Instruments and controls


“5. Starting and driving” section and “TIRE PRESSURE MONITORING SYSTEM (TPMS)” in the “6. In case of emergency” section.


TPMS malfunction:


If the TPMS is not functioning properly, the low tire pressure warning light will flash for approxi- mately 1 minute when the ignition switch is placed in the ON position. The light will remain on after 1 minute. Have the system checked by a NISSAN dealer.


For additional information, see “TIRE PRES- SURE MONITORING SYSTEM (TPMS)” in the “5. Starting and driving” section.


WARNING


If the light does not illuminate with the ignition switch placed in the ON position, have the vehicle checked by a NISSAN dealer as soon as possible.


If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with un- der-inflated tires may permanently damage the tires and increase the


Black plate (86,1)


likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driv- ing after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.


. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.


. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS.


Model "Z12-D" EDITED: 2010/ 9/ 27


CAUTION


The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.


If the vehicle is being driven at speeds of less than 16 MPH (25
km/h), the TPMS may not operate correctly.


. Be sure to install the specified size of tires to the four wheels correctly.


Low washer fluid warning light (Canada only)


This light illuminates when the washer fluid is at a low level. Add washer fluid as necessary. (See “WINDOW WASHER FLUID” in the “8. Main- tenance and do-it-yourself” section.)


P position selecting warning light (if so equipped)


The warning light blinks in red when the ignition switch is pushed to stop the engine with the selector lever in any position except the P (Park) position.


If this warning appears, move the selector lever


to the P (Park) position or push the ignition switch to the ON position.


An inside warning chime will also sound.


See “INTELLIGENT KEY SYSTEM” in the “3. Pre-driving checks and adjustments” section.


Seat belt warning light


The light and chime remind you to fasten seat belts. The light illuminates whenever the ignition switch is placed in the ON position, and will remain illuminated until the driver’s seat belt is fastened. At the same time, the chime will sound for about 6 seconds unless the driver’s seat belt is securely fastened.


for


the front The seat belt warning light illuminate if the seat belt is not passenger will is fastened when the front passenger’s seat occupied. For 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light the front passenger.


for


See “SEAT BELTS” in the “1. Safety — Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage.


Black plate (87,1)


Supplemental air bag warning light


After turning the ignition switch to the ON position, the supplemental air bag warning light will illuminate. The supplemental air bag warning light will turn off after about 7 seconds if the supplemental front air bag and supplemental side air bag, curtain side-impact air bag systems and/or pretensioner seat belt are operational.


If any of the following conditions occur, the front air bag, side air bag, curtain air bag and pretensioner systems need servicing and your vehicle must be taken to your nearest NISSAN dealer.


The supplemental air bag warning light remains on after approximately 7 seconds.


The supplemental air bag warning light flashes intermittently.


The supplemental air bag warning light does not illuminate at all.


Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioners may not function properly.


For additional information, see “SUPPLEMEN- TAL RESTRAINT SYSTEM” in the “1. Safety — Seats, seat belts and supplemental restraint system” section.


Instruments and controls 2-15


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (88,1)


WARNING


See “CRUISE CONTROL” in the “5. Starting and driving” section.


Malfunction Indicator Light (MIL)


If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.


INDICATOR LIGHTS


Cruise indicator light (if so equipped)


Cruise main switch indicator:


This light illuminates when the cruise control main switch is pushed. The light turns off when the main switch is pushed again. When the cruise indicator the cruise control system is operational.


illuminates,


light


Cruise malfunction:


the cruise indicator


light blinks while the If engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by a NISSAN dealer.


2-16 Instruments and controls


Front passenger air bag status light


The front passenger air bag status light (located on the center of the instrument panel) will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.


For front passenger air bag status light opera- tion, see “NISSAN ADVANCED AIR BAG SYSTEM (front seats)” in the “1. Safety — Seats, seat belts and supplemental restraint system” section of this manual.


Engine start operation indicator light (if so equipped)


This light appears when the selector lever is in the P (Park) position. This light means that the engine will start by pushing the ignition switch with the brake pedal depressed. You can start the engine directly in any position.


High beam indicator light


This light illuminates when the headlight high beam is on and goes out when the low beam is selected.


the malfunction indicator


If illuminates steady or blinks while the engine is running, it may indicate a potential emission control and/or Continuously Variable Transmission (CVT) mal- function.


light


The malfunction indicator light may also illumi- nate steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3
US gallons (11.4 liters) of fuel in the fuel tank.


light should After a few driving trips, the turn off if no other potential emission control system malfunction exists.


If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/ maintenance test. (See “READINESS FOR INSPECTION/MAINTENANCE (I/M) TEST” in the “9. Technical and consumer information” section.)


Operation:


The malfunction indicator light will illuminate in one of two ways: . Malfunction indicator light illuminated steady


Model "Z12-D" EDITED: 2010/ 9/ 27


If


— An emission control system and/or CVT malfunction has been detected. Check the fuel-filler cap. the LOOSE FUEL CAP warning message is displayed on the twin trip odometer, if the fuel-filler cap is loose or the cap and missing, light continue to drive the vehicle. The should turn off after a few driving trips. If the turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.


light does not


tighten or


install


. Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system.


To reduce or avoid emission control system damage:


a) Do not drive at speeds above 45 MPH


(72 km/h).


b) Avoid hard acceleration or deceleration.


c) Avoid steep uphill grades.


d) If possible, reduce the amount of cargo


being hauled or towed.


The malfunction indicator blinking and remain illuminated.


light may stop


Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle


Black plate (89,1)


towed to the dealer.


CAUTION


Continued vehicle operation without having the emission control system and/or CVT system checked and re- paired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system.


Overdrive off indicator light (if so equipped)


The overdrive off indicator light illuminates when the overdrive off mode is selected.


For additional information, see ““CONTINU- OUSLY VARIABLE TRANSMISSION (CVT)” in the “5. Starting and driving” section of this manual.


Security indicator light


The light blinks when the ignition switch is in the ACC, OFF or LOCK position. This function indicates the security system equipped on the vehicle is operational.


If the security system is malfunctioning, this light


will remain on while the ignition switch is in the ON position. For additional information, see “SECURITY SYSTEMS” later in this section.


Vehicle Dynamic Control (VDC) warning light


The light will blink when the Vehicle Dynamic Control (VDC) system is operating, thus alerting the driver that the vehicle is nearing its traction limits. The road surface may be slippery.


Low beam indicator light


The light illuminates when the headlight switch is turned to the


position.


Turn signal/hazard indicator lights


The light flashes when the turn signal switch lever or hazard switch is turned on.


Vehicle Dynamic Control (VDC) off indicator light


The light illuminates when the Vehicle Dynamic Control (VDC) off switch is pushed to OFF. This indicates that the VDC system is not operating. When the VDC off light and slip indicator light illuminate with the VDC system turned on, this light alerts the driver to the fact


indicator


Instruments and controls 2-17


Model "Z12-D" EDITED: 2010/ 9/ 27


that the VDC system’s fail-safe mode is operat- ing, for example the VDC system may not be functioning properly. Have the system checked by a NISSAN dealer. If a malfunction occurs in the system, the VDC system function will be canceled but the vehicle is still driveable. For additional information, see “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section of this manual.


AUDIBLE REMINDERS Key reminder chime


Models with Intelligent Key system:


A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position.


Make sure the ignition switch is pushed to the OFF position, and take the Intelligent Key with you when leaving the vehicle.


Models without Intelligent Key system:


The key reminder chime sounds if the driver’s side door is opened while the key is left in the ignition switch and the ignition switch is in the ACC, OFF or LOCK position. Remove the key and take it with you when leaving the vehicle.


Light reminder chime The light reminder chime will sound when the driver side door is opened with the light switch 2-18 Instruments and controls


in the switch is in the ACC, OFF or LOCK position.


position, and the ignition


or


Turn the light switch off when you leave the vehicle.


Brake pad wear warning The disc brake pads have audible wear warn- ings. When a brake pad requires replacement, it will make a high pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the warning sound is heard.


Parking brake reminder chime The parking brake reminder chime will sound if the vehicle is driven at more than 4 MPH (7
km/h) with the parking brake applied. Stop the vehicle and release the parking brake.


Seat belt warning chime The seat belt warning chime will sound for about 6 seconds unless the driver’s seat belt is securely fastened.


Black plate (90,1)


SECURITY SYSTEMS


SIC4160


Your vehicle has two types of security systems, as follows: . Vehicle security system . NISSAN Vehicle Immobilizer System


The security condition will be shown by the security indicator light.


VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audio alarm signals if someone opens the doors, or back door when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.


Model "Z12-D" EDITED: 2010/ 9/ 27


The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the vehicle, and always lock it when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.


Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features.


SIC2045


How to arm the vehicle security system 1. Close all windows.


The system can be armed even if the windows are open.


2. Models with Intelligent Key system:


Place the ignition switch in the OFF position and remove the Intelligent Key from the vehicle.


Models without Intelligent Key system:


Place the ignition switch in the LOCK position and remove the key.


Black plate (91,1)


3. Close all doors. Lock all doors. The doors


can be locked with:


a)


the LOCK Intelligent Key (if so equipped)


button on the keyfob or


b) any request switch (Intelligent Key


equipped model)


c)


d)


the power door lock switch


the key — master or mechanical (In- telligent Key equipped model)


4. Confirm that


the security indicator


light illuminates. The security indicator light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is placed in the ACC or ON position, the system will not arm.


Even when the driver and/or passengers are in the vehicle, the system will activate with all doors locked with the ignition switch in the LOCK position. When turning the ignition switch to the ACC or ON position, the system will be released.


Instruments and controls 2-19


Model "Z12-D" EDITED: 2010/ 9/ 27


Vehicle security system activation The vehicle security system will give the follow- ing alarm:


The headlights blink and the horn sounds intermittently.


The alarm automatically turns off after approximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again.


The alarm is activated by: . Unlocking the door without using the keyfob, the Intelligent Key (if so equipped) the request switch (if so equipped) or the key. (Even if the door is opened by releasing the door the alarm will activate.)


inside lock knob,


How to stop an activated alarm The alarm will stop by unlocking a door by button on the keyfob pushing the UNLOCK or Intelligent Key, pushing the request switch or using the key. The alarm will not stop if the ignition switch is placed in the ACC or ON position.


If the system does not operate as de- scribed above, have it checked by a NISSAN dealer.


2-20 Instruments and controls


NISSAN VEHICLE IMMOBILIZER SYS- TEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key.


If the engine fails to start using the registered key, it may be due to interference caused by another registered key, an automated toll road device or automated payment device on the key ring. Restart the engine using the following procedures:


1. Leave the ignition switch in the ON position


for approximately 5 seconds.


2. Place the ignition switch in the OFF or LOCK position and wait approximately 10
seconds.


3. Repeat step 1 and 2 again.


4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key.


If this procedure allows the engine to start, NISSAN recommends placing the regis- tered key on a separate key ring to avoid interference from other devices.


Statement related to section 15 of FCC rules for NISSAN Vehicle Immobilizer System (CONT ASSY-BCM. ANT ASSY- IMMOBILISER)


Black plate (92,1)


This device complies with part 15 of the FCC Rules and RSS-210 of Industry Cana- da. Operation is subject to the following two conditions;


(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.


CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPER- ATE THE EQUIPMENT.


Model "Z12-D" EDITED: 2010/ 9/ 27


service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service.


SIC2045


Security indicator light The security indicator light is located on the meter panel. the NISSAN Vehicle Immobilizer System.


indicates the status of


It


The light blinks after the ignition switch was in the LOCK position. This function indicates the security systems equipped on the vehicle are operational.


If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.


If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System


Black plate (93,1)


WINDSHIELD WIPER AND WASHER SWITCH


WARNING


In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.


CAUTION


. Do not operate the washer continu-


ously for more than 30 seconds.


. Do not operate the washer if the


reservoir tank is empty.


. Do not


fill


the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.


. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to


Instruments and controls 2-21


Model "Z12-D" EDITED: 2010/ 9/ 27


Black plate (94,1)


Pull the lever toward you *5
to operate the washer. Then the wiper will also operate several times.


mix the washer fluid concentrate and water.


If the windshield wiper operation is inter- rupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approximately 1
minute, turn the switch on again to operate the wiper.


The windshield wiper and washer operates when the ignition switch is in the ON position.


SIC3664


Push the lever down to operate the wiper at the following speed: *1


Intermittent — intermittent operation can be adjusted by turning the knob toward *A (Slower) or *B (Faster).


*2 Low — continuous low speed operation *3 High — continuous high speed operation Push the lever up *4
to have one sweep operation of the wiper.


2-22 Instruments and controls


Model "Z12-D" EDITED: 2010/ 9/ 27


REAR WINDOW WIPER AND WASHER SWITCH


WARNING


and water.


If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.


In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.


CAUTION


. Do not operate the washer continu-


ously for more than 30 seconds.


. Do not operate the washer if the


reservoir tank is empty.


. Do not


fill


the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.


. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate


Black plate (95,1)


The rear window wiper and washer operate when the ignition switch is in the ON position.


SIC3666


Turn the switch clockwise from the OFF position to operate the wiper. *1


Intermittent (INT) — intermittent operation (not adjustable)


tion


*2 Low (ON) — continuous low speed opera- Push the switch forward *3
to operate the washer. Then the wiper will also operate several times.


Instruments and controls 2-23

Loading...
x