Download PDF Manual

4. Confirm that the SECURITY indicator light comes on. The SECURITY light stays on for about 30 seconds. The vehicle security sys- tem is now pre-armed. After about 30 sec- onds the vehicle security system automati- cally shifts into the armed phase. The SECURITY light begins to flash once every 3
seconds. If, during the 30-second pre-arm time period, the door is unlocked by the key or the keyfob, or the ignition key is turned to ACC or ON, the system will not arm.


c If the key is turned slowly when locking the door, the system may not arm. Fur- thermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is re- moved. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.


c Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors and trunk lid closed and locked with the ignition key in the OFF position.


Vehicle security system activation The vehicle security system will give the following alarm: c The headlights blink and the horn sounds


intermittently.


c The alarm automatically turns off after ap- proximately 45 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking a door or trunk lid with the key, or by pressing the


button on the keyfob.


The alarm is activated by: c opening the door or trunk lid without using the key or keyfob (even if the door is un- locked by releasing the door inside lock switch).


How to stop an activated alarm The alarm stops only by unlocking a door or the trunk lid with the key, or by pressing the button on the keyfob.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


WIC0271


Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. To deactivate: Press and hold both the and 2 seconds.


buttons at the same time for at least


The hazard lights will quickly flash 3 times to confirm that the horn beep feature has been deactivated. To activate: Press and hold both the and 2 seconds once more.


buttons at the same time for at least


The hazard lights will quickly flash once and the horn will sound once to confirm that the horn beep feature has been reactivated.


Deactivating the horn feature does not silence the horn if the alarm is triggered. If the system does not operate as described above, have it checked by a NISSAN dealer. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The NISSAN Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of a registered NVIS key. If the engine fails to start using a registered NVIS key (for example, when interference is caused by another NVIS key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following proce- dures: 1. Leave the ignition switch in the ON position


for approximately 5 seconds.


2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 5 seconds.


3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered NVIS key.


If the no start condition re-occurs, NISSAN rec- ommends placing the registered NVIS key on a separate key ring to avoid interference from other devices. Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY (cid:151) IMMOBILIZER, ANT ASSY (cid:151) IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE MANUFAC- TURER FOR COMPLIANCE COULD VOID THE USER(cid:146)S AUTHORITY TO OPERATE THE EQUIPMENT.


Instruments and controls 2-15


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


WINDSHIELD WIPER AND WASHER SWITCH


If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NVIS service as soon as possible. Please bring all NVIS keys that you have when visiting your NISSAN dealer for service.


WIC0270


Security indicator light (NISSAN Ve- hicle Immobilizer System) The security indicator light s1 is located on the instrument panel near the windshield. The security indicator light blinks every 3 sec- onds whenever the ignition switch is in the LOCK, OFF or ACC position. This function indi- cates the NISSAN Vehicle Immobilizer System (NVIS) is operational. If the NVIS is malfunctioning, the light will remain on while the ignition key is in the ON position.


2-16 Instruments and controls


WIC0613


SWITCH OPERATION The windshield wiper and washer switch oper- ates when the ignition key is in the ON position.


Push the lever down to operate the wiper at the following speed: s1


Intermittent (cid:151) intermittent operation can be adjusted by turning the knob toward sA (Slower) or sB (Faster). s2
Low (cid:151) continuous low speed operation s3 High (cid:151) continuous high speed operation Push the lever up s4 to have one sweep opera- tion of the wiper.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


Pull the lever toward you s5
to operate the washer. The wiper will also operate several times.


WARNING


In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.


CAUTION


c Do not operate the washer continu-


ously for more than 30 seconds.


c Do not operate the washer if the reser-


voir tank is empty.


c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may perma- nently stain the grille if spilled while fill- ing the window washer reservoir tank.


c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.


REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH


WIC0272


LIC0317


Type A


To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster light on the switch comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes.


indicator


Type B


CAUTION


When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.


NOTE: The top few rows of wires on the rear win- dow are not part of the rear window de- froster system. These wires make up the antenna for the audio system.


Instruments and controls 2-17


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


(for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon head- lights is not reduced.


c If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blink- ing, or the color of the light will be- come reddish. If one or more of the above signs appear, contact a NISSAN dealer.


HEADLIGHT AND TURN SIGNAL SWITCH


XENON HEADLIGHTS (if so equipped)


WARNING


cHIGH VOLTAGE


c When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer.


c Xenon headlights provide considerably more light than conventional head- lights. If they are not correctly aimed, they might temporarily blind an oncom- ing driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your vehicle to a NISSAN dealer and have the headlights adjusted correctly.


When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize. c The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn off the headlights for short intervals


Type C


LIC0637


2-18 Instruments and controls


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


Type A


Type B


Type C


WIC0312


WIC0313


WIC0314


HEADLIGHT CONTROL SWITCH Lighting s1 When turning the switch to the


posi- tion, the front parking, tail, license plate and instrument panel lights come on. s2 When turning the switch to the


posi- tion, the headlights come on and all the other lights remain on.


Instruments and controls 2-19


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


WIC0597


Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: c Turn on the headlights automatically when it


is dark. See your NISSAN dealer to have the autolight activation sensitivity setting adjusted.


c Turn off the headlights when it is light. c Keep the headlights on for up to 180 sec- onds after you turn the key to OFF, open and


2-20 Instruments and controls


close the driver(cid:146)s or passenger(cid:146)s door, and then close all doors. The default time delay for autolight shutoff is 45 seconds. See your NISSAN dealer to have the time delay setting adjusted.


If the ignition switch is turned OFF and one of the doors is opened, the headlights remain ON for 5
minutes. To set the autolight system: 1. Make sure the headlight switch is in the


AUTO position s1 .


2. Turn the ignition key to ON. 3. The autolight system automatically turns the


headlights on and off.


, or


position.


To turn the autolight system off, turn the switch to the OFF, Be sure you do not put anything on top of the autolight sensor located in the top driver side of the instrument panel. The autolight sensor controls the autolight; if it is covered, the autolight sensor reacts as if it is dark out and the headlights will illumi- nate. If this occurs while parked with the engine off and the key in the ON position, your vehicle(cid:146)s battery could become dis- charged.


LIC0318


Headlight beam select s1 To select the high beam function, push the lever forward. The high beam lights come on and the


light illuminates.


s2 Pull the lever back to select the low beam. s3 Pulling and releasing the lever flashes the


headlight high beams on and off.


Battery saver system If the ignition switch is turned OFF while the headlight switch is in the posi- tion, the headlights will turn off after 5 minutes.


or


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


CAUTION


WARNING


c Be sure to turn the light switch to the OFF position when you leave the ve- hicle for extended periods of time, oth- erwise the battery will go dead.


c Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.


DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position for full illumination when driving at night.


If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is turned off.


When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.


WIC0273


INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the igni- tion switch is in ON position. The instrument brightness control operates when the the AUTO, Turn the control to adjust the brightness of instru- ment panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off.


headlight or


position.


control


switch


in


is


Instruments and controls 2-21


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


were left ON. The fog lights will be turned OFF by the Battery Saver function approxi- mately 5 minutes after is closed.


the last door


c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Battery Saver function, the fog lights will immediately come back ON.


Headlight switch in the AUTO position; nighttime operation c Fog lights, marker and taillights come ON. c Headlights come ON.


The lights can be adjusted to turn ON in brighter or dimmer environments. See your NISSAN dealer to have the sensi- tivity setting adjusted.


c Dash readouts dim unless the dimmer


switch is on full bright.


c If the ignition switch is in the OFF position with the fog lights turned ON, the fog lights will be turned OFF by the Twilight Sentinel function approximately 45 seconds after the last door is closed. The default setting is 45 seconds. See your NISSAN dealer to have this time adjusted up to 180 seconds.


LIC0319


TURN SIGNAL SWITCH Turn signal s1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.


Lane change signal s2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.


2-22 Instruments and controls


WIC0320
FOG LIGHT SWITCH (if so equipped) Normal operation of the fog lights in the ON position: Headlight switch in the AUTO position; day- time operation c Fog lights, marker and taillights come ON. c Headlights do not come ON. c Dash readouts dim unless the dimmer


switch is on full bright.


c If the ignition switch is in the OFF position with the fog lights turned ON, a warning chime will sound indicating the fog lights


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


c If any door is opened when the ignition switch is in the OFF position, the Twilight Sentinel function operates for approximately 5 minutes. After approximately 5 minutes, the lights will turn OFF due to the Battery Saver function.


c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Twilight Sentinel function, the fog lights and the headlights will come ON to- gether when the Auto Light Sensor deter- mines it is dark enough. The fog lights will now operate independently of the headlights only if the headlight switch is turned OFF.


c When the high beams are turned ON, the fog lights will turn OFF. The fog lights will come back ON when the high beams are turned OFF.


Headlights turned ON and OFF by the driver (no AUTO headlight function); day or nighttime operation c Same operation as (cid:147)Headlight switch in the AUTO position; daytime operation(cid:148) de- scribed above.


Some of the Battery Saver and Twilight Sentinel functions can be turned ON and OFF or adjusted. Please see your NISSAN dealer if you have any questions.


HAZARD WARNING FLASHER SWITCH


To turn the fog lights OFF, turn the switch to the OFF position. The fog lights automatically turn off whenever the high beam headlight function is selected.


WIC0275


Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash.


WARNING


c If stopping for an emergency, be sure to


move the vehicle well off the road.


c Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.


Instruments and controls 2-23


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


c Turn signals do not work when the haz-


ard warning flasher lights are on.


The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.


2-24 Instruments and controls


HORN


HEATED SEAT (if so equipped)


WIC0249


LIC0136


To sound the horn, push the center pad area of the steering wheel.


WARNING


Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.


The front seats are warmed by built-in heaters (if so equipped). The switches are located on the center console.


1. Start the engine.


2. Push the low or high position of the switch, as desired, depending on the temperature. The indicator light in the switch will illumi- nate.


The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off.


c The battery could run down if the seat heater is operated while the engine is not running.


TRACTION CONTROL SYSTEM (TCS) OFF SWITCH (if so equipped)


CAUTION


c Do not use the seat heater for extended periods or when no one is using the seat.


c Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated.


c Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.


c Any liquid spilled on the heated seat should be removed immediately with a dry cloth.


c When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials.


c If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.


LIC0134
The vehicle should be driven with the Traction Con- trol System (TCS) on for most driving conditions. When the vehicle is stuck in mud or snow, the TCS reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maxi- mum engine power is needed to free a stuck vehicle, turn the TCS off. To turn off the TCS, push the TCS OFF switch. The Push the (cid:147)TCS OFF(cid:148) switch again or restart the engine and the system will operate normally. See (cid:147)Traction control system (TCS)(cid:148) in the (cid:147)Starting and driving(cid:148) section.


indicator will come on.


Instruments and controls 2-25


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


POWER OUTLET


c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may blow.


c When not in use, be sure to close the cap. Do not allow water to contact the outlet.


Instrument panel


Console


WIC0276


WIC0277


The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 volt, 120W (10A) maximum.


CAUTION


c The outlet and plug may be hot during


or immediately after use.


c This power outlet is not designed for


use with a cigarette lighter unit.


c Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.


2-26 Instruments and controls


c Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged battery.)


c Avoid using when the air conditioner, headlights or rear window defroster is on.


c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


STORAGE


MAP POCKETS


LIC0614


LIC0016


WIC0609


SEATBACK POCKETS (if so equipped) The seatback pockets are located on the back of the driver(cid:146)s and passenger(cid:146)s seats. The pockets can be used to store maps.


SUNGLASSES HOLDER To open the sunglasses holder, push and release.


WARNING


The sunglasses case should not be used while driving so full attention may be given to vehicle operation.


Instruments and controls 2-27


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


CAUTION


c Do not use for anything other than


sunglasses.


c Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses.


2-28 Instruments and controls


WIC0278


WRS0167


Front


CUP HOLDERS To open the front cup holders, lift the lid. To close, lower the lid. The cup holder insert can be used for holding smaller cups and has a different size on each end. With the desired size facing up, push the cup holder insert down into the cup holder to secure it tightly before use. The rubber inserts may be removed for cleaning. The rear cup holders are located in the fold-down armrest in the rear seat back.


Rear


WARNING


The cup holder should not be used while driving so full attention may be given to vehicle operation.


CAUTION


c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.


c Use only soft cups in the cup holder. Hard


objects can injure you in an accident.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


CONSOLE BOX


WARNING


The center console box should not be used while driving so full attention may be given to vehicle operation.


CAUTION


c This power outlet is not designed for


use with a cigarette lighter unit.


c Do not use accessories that exceed 12
volt, 120W (10A) power draw. Do not use double adapters or more than one elec- trical accessory.


WIC0283


Armrest Push the button to elevate the armrest. To return armrest to regular position, push armrest rear- ward until locked.


WIC0374


GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking s1 or unlocking s2 the glove box. The valet key cannot be used to lock or unlock the glove box.


WARNING


Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.


Instruments and controls 2-29


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


To route a phone cord to the power outlet: 1. Open the upper half of the console box. 2. Remove the felt mat, and then remove the


cutout area from the mat.


3. Remove the access hole cover. 4. 5. Route the phone cord through the access


Install the felt mat.


hole and plug into the power outlet.


WIC0281


Upper half Pull up on the lever to open the upper half of the console box. The felt mat may be removed for cleaning. The upper half of the console box may be used for storage of cellular phones. An access hole is provided at the bottom of the upper half of the console box for phone cord routing to the power outlet.


2-30 Instruments and controls


WIC0282


Lower half Pull up on the lever to open the lower half of the console box. A power outlet is located inside the console box and there is storage for compact discs.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


COVERED STORAGE BOX Push the bottom center of the lid to open.


WIC0284


WIC0610


Instruments and controls 2-31


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


CARGO NET (if so equipped) The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion. To install the cargo net, attach the hooks to the retainers. To remove the cargo net, detach the hooks from the cargo net retainers.


WARNING


c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.


c Be sure to secure all four hooks into the retainers. The cargo restrained in the net must not exceed 30 lbs. (13.6 kg) or the net may not stay secured.


2-32 Instruments and controls


WINDOWS


POWER WINDOWS


WARNING


c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.


WIC0285


Door lock/unlock button


1. 2. Window lock button 3.


Front passenger side (automatic switch, if so equipped) Right rear passenger side Left rear passenger side Driver side automatic switch


4. 5. 6. Driver(cid:146)s side power window switch The driver(cid:146)s side control panel is equipped with switches to open or close all of the windows.


The power windows operate when the ignition switch is in the ON position, or for about 45
seconds after the ignition switch is turned to the


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


OFF position. If the driver(cid:146)s or passenger(cid:146)s door is opened during this period of about 45 sec- onds, power to the windows is canceled. To open a window, push the switch and hold it down. To close a window, pull the switch up. To stop the opening or closing function at any time, simply release the switch.


WIC0286
Front passenger power window switch The passenger window switch operates only the corresponding passenger window. To open the window, push the switch and hold it down s1 . To close the window, pull the switch up s2 .


LIC0321


Rear power window switch The rear passenger window switches open or close only the corresponding passenger window. To open the window, push the switch and hold it down s1 . To close the window, pull the switch up s2 . Locking passengers(cid:146) windows When the window lock button is depressed, only the driver side window can be opened or closed. Push it again to cancel the window lock function.


Instruments and controls 2-33


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


Auto-reverse function If the control unit detects something caught in the window as it is closing, the window will be imme- diately lowered. The auto-reverse function can be activated when the window is closed by automatic operation when the ignition key is in the ON position or for 45 seconds after the ignition key is turned to the OFF position. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs.


WARNING


There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.


SUNROOF (if so equipped)


Type A


WIC0611


AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position. The automatic sunroof is operational for about 45 seconds, even if the ignition key is turned to the ACC or OFF position. If the driver(cid:146)s door or the front passenger(cid:146)s door is opened during this period of about 45 sec- onds, power to the sunroof is canceled.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


WIC0288


Automatic operation To fully open a window equipped with automatic operation, press the window switch down (only driver(cid:146)s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening.


To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held.


2-34 Instruments and controls


position s2 .


To fully close the sunroof, push and hold the switch toward the Tilting the sunroof Type A To tilt the sunroof up, first close the sunroof by pushing the switch toward UP/CLOSE. Release the switch, then push the switch toward UP/CLOSE. The sunroof will tilt up. To tilt the sunroof down, push the switch toward DOWN/OPEN. Type B To tilt the sunroof up, push the tilt switch toward the To tilt the sunroof down, push and hold the tilt switch toward the


position s3 .


position s4 .


LIC0679


Type B


Sliding the sunroof Type A


To open the sunroof, push and hold the switch toward DOWN/OPEN. Release the switch when the sunroof is in the desired position.


To close the sunroof, push and hold the switch toward UP/CLOSE until is fully closed.


the sunroof


Type B


To fully open the sunroof, push the switch toward the


position s1 .


WARNING


c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.


c Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing.


CAUTION


c Remove water drops, snow, ice or sand


from the sunroof before opening.


c Do not place heavy objects on the sun-


roof or surrounding area.


Restarting the sunroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electri- cal supply interrupted and/or some abnormality detected. Use the following reset procedure to return sunroof operation to normal.


Type A


1. From any sunroof position (full open, partially open, closed, partially vented or vented), push and hold the button in the forward position until the sunroof vents in the full-up position. The sunroof should now operate normally.


Type B 1. From any sunroof position (full open, partially open, closed, partially vented or vented), push and hold the tilt switch toward position s3 until the sunroof vents the in the full-up position. The sunroof should now operate normally.


Instruments and controls 2-35


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


INTERIOR LIGHT


Sun shade Open and close the sun shade by sliding it for- ward or backward.


WIC0264


The interior light has a three-position switch and operates regardless of ignition switch position. When the switch is in the ON position s1 , the interior lights illuminate, regardless of door posi- tion. The lights will go off after about 30 minutes unless the ignition key is in the ACC or ON position.


When the switch is in the center O position, the interior lights will stay on for about 30 seconds when: c The doors are unlocked by the keyfob, a key or the power door lock switch while all doors


2-36 Instruments and controls


are closed and the ignition switch is in the OFF position.


c The driver(cid:146)s door is opened and then closed while the key is removed from the ignition switch.


c The key is removed from the ignition switch


while all doors are closed.


The lights will turn off while the 30 second timer is activated when: c The driver(cid:146)s door is locked by the keyfob, a


key, or the power door lock switch.


c The ignition switch is turned ON. When the switch is in the OFF position s2 , the interior lights do not illuminate, regardless of door position.


The lights will turn off automatically after 30 min- utes while doors are open to prevent the battery from becoming discharged.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


MAP LIGHTS


NOTE: The door step lights illuminate when the driver and passenger doors are open re- gardless of the interior light switch posi- tion. These lights will turn off automatically after about 30 minutes while doors are open to prevent the battery from becoming discharged.


CAUTION


Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.


Models without sunroof


Models with sunroof (cid:151) Type A


WIC0289


WIC0290


To turn the map lights on, press the switches. To turn them off, press the switches again.


CAUTION


Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.


Instruments and controls 2-37


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


TRUNK LIGHT


The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. For bulb replacement procedures, refer to (cid:147)Bulb replacement(cid:148) in the (cid:147)Maintenance and do-it- yourself(cid:148) section of this manual.


HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped)


The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: c Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems.


c Is powered by your vehicle(cid:146)s battery. No separate batteries are required. If the vehi- cle(cid:146)s battery is discharged or is discon- nected, HomeLinkT will retain all program- ming.


Once the HomeLinkT Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (i.e., new vehicle purchases). Upon sale of the vehicle, the programmed HomeLinkT Universal Transceiver buttons should be erased for security purposes. For addi- tional information refer to (cid:147)Programming HomeLinkT(cid:148) later in this section.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


Models with sunroof (cid:151) Type B


LIC0696


2-38 Instruments and controls


WARNING


c Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.


c During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.


c Your vehicle(cid:146)s engine should be turned off while programming the HomeLinkT Universal Transceiver.


WIC0291


PROGRAMMING HOMELINKT 1. With the ignition key in the OFF position, press and hold the two outside buttons, and release when the indicator light begins to flash (approximately 20 seconds). This pro- cedure erases the factory set default codes and does not have to be followed when programming additional hand-held transmit- ters.


2. Hold the end of the hand-held transmitter (from the device you wish to train) approxi- mately 2 - 5 inches (50 - 127 mm) away from the surface of HomeLinkT keeping the indi- cator light in view.


3. Using both hands, simultaneously push the hand-held transmitter button and the de- sired HomeLinkT button. Do not release the buttons until step 4 has been completed.


NOTE: Some garage door openers may require the procedures noted under (cid:147)Canadian Pro- gramming.(cid:148) 4. The HomeLinkT indicator will


first slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing light indicates the HomeLinkT Universal Transceiver has been successfully programmed.


flash,


To program the remaining two buttons, follow steps 2 through 4. If , after repeated attempts, you do not success- fully program the HomeLinkT Universal Trans- ceiver to learn the signal of the hand-held trans- mitter, refer to (cid:147)Rolling Code Programming(cid:148) later in this section.


Instruments and controls 2-39


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (note steps 2 - 4 under (cid:147)Pro- gramming HomeLinkT(cid:148)) while you press and re- press ((cid:147)cycle(cid:148)) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).


NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the (cid:147)cycling(cid:148) process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLinkT Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted.


2-40 Instruments and controls


PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLinkT does not quickly learn the hand- held transmitter information: c replace the hand-held transmitter batteries


with new batteries.


c position the hand-held transmitter with its from the


facing


away


battery HomeLinkT surface.


area


c press and hold both the HomeLinkT and hand-held transmitter buttons without inter- ruption.


c position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the HomeLinkT surface. Hold the transmitter in that position for up to 15 seconds. If HomeLinkT is not programmed within that time, try holding the transmitter in another position (cid:150) keeping the indicator light in view at all times.


If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual.


CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). ROLLING CODE PROGRAMMING Rolling code garage door openers (or other roll- ing code devices) which are (cid:147)code protected(cid:148) and manufactured after 1996, may be deter- mined by the following: c Reference the garage door opener Owner(cid:146)s


Manual for verification.


c The hand-held transmitter appears to pro- gram the HomeLinkT Universal Transceiver but does not activate the garage door.


c Press and hold the trained HomeLinkT but- ton. If the garage door opener has the rolling code feature, the HomeLinkT indicator light will flash rapidly, then remains on after 2
seconds.


To program the HomeLinkT Universal Transceiver to a garage door opener with the rolling code feature, follow these instructions after completing the (cid:147)Programming HomeLink(cid:148) (the aid of a sec- ond person may make the following procedures quicker and easier).


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


1. Locate the training button on the garage door opener motor unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the garage door opener Owner(cid:146)s Manual.


2. Press the training button on the garage door opener motor unit (which may activate a training light).


NOTE: Following step 2, there are 30 seconds in which to initiate step 3. 3. Firmly press and release the programmed HomeLinkT button a second time to com- plete the training process. (Some garage door openers may require you to do this procedure a third time to complete the train- ing.)


The garage door opener should now recognize the HomeLinkT Universal Transceiver and acti- vate when the HomeLinkT button is pressed. The remaining two buttons may now be programmed (if not yet programmed, follow steps 2 through 4
in the (cid:147)Programming HomeLinkT(cid:148) procedures earlier in this section).


REPROGRAMMING A SINGLE HOMELINKT BUTTON To reprogram a HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT but- ton. Do not release the button until step 4
has been completed.


2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 1 - 3 inches (26 - 76
mm) away from the HomeLinkT surface.


3. Press and hold the hand-held transmitter


button.


4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.


The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not affect any other programmed HomeLinkT buttons.


IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLinkT. Consult the Owner(cid:146)s Manual of each device or call the manu- facturer or dealer of those devices for additional information. When your vehicle is recovered, you will need to reprogram the HomeLinkT Univer- sal Transceiver with your new transmitter information. FCC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This de- vice must accept any interference that may be received, including interference that may cause undesired operation. This transmitter has been tested and com- plies with FCC and DOC/MDC rules. Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the device. DOC: ISTC 1763K1313
FCC I.D. CV2V67690


Instruments and controls 2-41


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/10/03—tbrooks X


MEMO


2-42 Instruments and controls


3 Pre-driving checks and adjustments


Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2


Nissan vehicle immobilizer system (NVIS) keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . 3-4
Locking with power door lock switch . . . . . . . . . . . . . 3-4
Child safety rear door lock. . . . . . . . . . . . . . . . . . . . . . . 3-5
Remote keyless entry system (if so equipped). . . . . . . . . 3-5
How to use remote keyless entry system . . . . . . . . . . 3-6
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10
Trunk lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Opener operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Key operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12


Interior trunk lid release . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Fuel filler lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Opener operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Fuel filler cap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Tilting telescopic steering column . . . . . . . . . . . . . . . . . . 3-14
Tilt operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Telescopic operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
Vanity mirrors (if so equipped). . . . . . . . . . . . . . . . . . . 3-15
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
Inside mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Automatic anti-glare inside mirror (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Outside mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


KEYS


1.


WPD0128
Two master keys (black) with transpon- der chip and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip Key number plate Transponder chip


2. 3. 4. A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate.


3-2 Pre-driving checks and adjustments


previously registered into the NISSAN Vehicle Immobilizer System. After the registration pro- cess, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer Sys- tem (NVIS) during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle. Do not allow the immobilizer system key, which contains an electrical transponder, to come into contact with salt water. This could affect system function.


A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) KEYS You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.


The master key can be used for all the locks.


The valet key cannot be used for the trunk lid, glove box lock or rear seatback lock.


To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can dupli- cate your existing key. As many as five NVIS keys can be used with one vehicle. You should bring all NVIS keys that you have to your NISSAN dealer for registration. This is because the registration process will erase the memory of all key codes


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


DOORS


WARNING


c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders.


c Before opening any door, always look


for and avoid oncoming traffic.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.


Opening and closing windows (if so equipped) The driver(cid:146)s door key operation allows you to open and close windows equipped with auto- matic operation at the same time. c To open the windows, turn the driver(cid:146)s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. c To close the windows, turn the driver(cid:146)s door key to the front of the vehicle for longer than 1 second after the door is locked.


Driver(cid:146)s side


WPD0129


LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors at the same time. Turning the key toward the front s1 of the vehicle locks all doors. Turning the key one time toward the rear s2 of the vehicle unlocks that door. From that position, returning the key to neutral s3 (where the key can only be removed and inserted) and turning it toward the rear again within 5 seconds unlocks all doors s4 .


Pre-driving checks and adjustments 3-3


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


Lockout protection When the power door lock switch (driver or front passenger) is moved to the lock position with the key in the ignition and any door open, all doors will lock and unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle.


Inside lock


Driver(cid:146)s side


WPD0130


WPD0131


LOCKING WITH INSIDE LOCK KNOB To lock the door without the key, move the inside lock to the lock position s1 , then close the door. To unlock the door without the key, move the inside lock knob to the unlock position s2 .


LOCKING WITH POWER DOOR LOCK SWITCH To lock all the doors without a key, push the door lock switch (driver or front passenger side), to the lock position s1 . When locking the door this way, be certain not to leave the key inside the vehicle. To unlock all the doors without a key, push the door lock switch (driver or front passenger side) to the unlock position s2 .


3-4 Pre-driving checks and adjustments


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


c Do not place the keyfob for an extended period in an area where temperatures exceed 140(cid:176)F (60(cid:176)C).


REMOTE KEYLESS ENTRY SYSTEM (if so equipped)


It is possible to lock/unlock all doors, turn the interior light on, and activate the panic alarm by using the keyfob from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors.


The keyfob can operate at a distance of approxi- mately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle.


As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.


The keyfob will not function when: c the battery is discharged c the distance between the vehicle and the


keyfob is over 33 ft (10 m)


CAUTION


Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become wet. c Do not drop the keyfob. c Do not strike the keyfob sharply against


another object.


APD1010
CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.


Pre-driving checks and adjustments 3-5


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


WPD0132


HOW TO USE REMOTE KEYLESS ENTRY SYSTEM Locking doors 1. Close all windows 2. Remove the key from the ignition switch. 3. Close the hood, trunk lid and all doors.


3-6 Pre-driving checks and adjustments


4. Push the


button on the keyfob. All the doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.


c When the


button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked.


c If a door is open and you push the


button, the doors will lock but the horn will not beep and the hazard lights will not flash. The horn may or may not beep once. Refer to (cid:147)Silencing the horn beep feature(cid:148) later in this section for details.


WPD0133


button on the keyfob once.


Unlocking doors Push the c Only the driver(cid:146)s door unlocks. c The hazard indicator flashes once if all doors are completely closed with the ignition key in any position except the ON position.


c The interior light turns on and the light timer activates for 30 seconds when the switch is in the center O position with the ignition key in any position except the ON position.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


button on the keyfob again within


Push the 5 seconds. c All doors unlock. c The hazard indicator flashes once if all doors


are completely closed.


The interior lights can be turned off without wait- ing 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the OFF position. Auto relock When the button on the keyfob is pushed, all doors will lock automatically within 1 minute unless one of the following operations is per- formed: c Any door is opened. c A key is inserted into the ignition switch and


the key is turned from OFF to ON.


WPD0134


WPD0135


Releasing the trunk lid Push the button on the keyfob for longer than 0.5 second to open the trunk lid. The trunk release button on the keyfob will not operate when the key is in the ignition switch. The trunk lid will open when using the key- fob even if the trunk lid release cancel switch is turned to OFF. See (cid:147)Trunk lid(cid:148) later in this section for cancel switch infor- mation.


Using the panic alarm If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention by pushing and holding the button on the keyfob for longer than 0.5 second. The panic alarm and headlights will stay on for 25
seconds. The panic alarm stops when: c it has run for 25 seconds, or c any button is pushed on the keyfob.


Pre-driving checks and adjustments 3-7


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


WIC0271


buttons for at least 2 seconds.


Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the keyfob. To deactivate: Press and hold the and The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and once more. The hazard lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. 3-8 Pre-driving checks and adjustments


buttons for at least 2 seconds


Deactivating the horn beep feature does not si- lence the horn if the alarm is triggered. Using the interior light The interior light can be turned off without waiting 30 seconds by inserting the key into the ignition, locking the doors with the keyfob or pushing the interior light button to OFF. Opening windows (if so equipped) The keyfob allows you to open the front windows simultaneously. c To open the front windows, press the


button on the keyfob for longer than 3
seconds after all doors are unlocked.


button on the keyfob.


The door windows will open while pressing the This opening windows function of the keyfob can be suspended using a CONSULT-II diagnostic tool. Please contact a NISSAN dealer. The door windows cannot be closed by using the keyfob.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


5. Press the LOCK button, then the UNLOCK button two or three times to check the key- fob operation.


If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.


c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.


FCC Notice: Changes or modifications not expressly ap- proved by the manufacturer for compliance could void the user(cid:146)s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device. Pre-driving checks and adjustments 3-9


BATTERY REPLACEMENT Replace the battery in the keyfob as follows: s1 Open the lid using a coin. s2 Remove the battery.


s3


WPD0136
Install a new battery with the (cid:147)+(cid:148) facing down.


Recommended battery: Sanyo CR2025 or equivalent. s4 Close the lid securely.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


HOOD


5. When closing the hood, return the support rod to its original position, lower the hood to approximately 12 inches above the latch and release it. This allows proper engagement of the hood latch.


WARNING


c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.


c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.


s1 Pull the hood lock release handle located below the driver side instrument panel; the hood springs up slightly.


s2


Lift the lever at the front of the hood with your fingertips and raise the hood.


3-10 Pre-driving checks and adjustments


s3 Remove the support rod from the clamp. s4


Insert the support rod into the slot on the passenger side fender ledge.


LPD0072


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


TRUNK LID


Driver(cid:146)s side


OPENER OPERATION


WPD0137


WARNING


c Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See (cid:147)Ex- haust gas(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.


c Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in- jured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children(cid:146)s access to car keys.


The trunk lid opener lever is located below the armrest of the driver(cid:146)s door trim panel. To open the trunk lid, pull the opener lever out. To close the trunk lid, lower and push the trunk lid down securely.


NOTE: You cannot open the trunk lid with the trunk lid opener lever if the vehicle security system (if so equipped) is armed.


LPD0085


Cancel switch (if so equipped) When the cancel switch located inside the glove box is OFF, the trunk lid cannot be opened with the trunk lid release switch. It can be opened with the master key or keyfob.


Pre-driving checks and adjustments 3-11


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


To open the trunk from the inside, rotate the illuminated lever until the lock releases and push up on the trunk lid. The release lever is made of a material that glows in the dark after a brief expo- sure to ambient light. The handle is located inside the trunk compart- ment on the trunk lock at the center of the trunk lid.


WPD0138


WPD0261


KEY OPERATION To open the trunk lid, turn the key clockwise. To close the trunk lid, lower and push the trunk lid down securely.


INTERIOR TRUNK LID RELEASE


WARNING


Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children(cid:146)s access to car keys.


The interior trunk lid release mechanism provides a means of escape for children and adults in the event they become locked inside the trunk.


3-12 Pre-driving checks and adjustments


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


FUEL FILLER LID


WPD0149


LPD0189


OPENER OPERATION The fuel filler opener lever is located on the out- side of the driver(cid:146)s seat s1 . To open the fuel filler lid, pull the opener lever up. To lock, close the fuel filler lid securely.


FUEL FILLER CAP The fuel filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard.


WARNING


c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.


c Fuel may be under pressure. Turn the cap a third of a turn, and wait for any- (cid:147)hissing(cid:148) sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.


c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.


c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on. c Never pour fuel into the throttle body to


attempt to start your vehicle.


c Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle ortrailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the


ground when filling.


Pre-driving checks and adjustments 3-13


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


TILTING TELESCOPIC STEERING COLUMN


c For additional


information, see the (cid:147)Malfunction indicator lamp (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section earlier in this manual.


(cid:150) Do not use electronic devices when


filling.


(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.


(cid:150) Use only approved portable fuel con-


tainers for flammable liquid.


CAUTION


c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.


c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap properly may cause the mal- function indicator lamp (MIL) to illumi- nate. If the lamp illuminates be- cause the fuel filler cap is loose or missing, tighten or install the cap and to continue vehicle. The lamp should turn off after a


drive


the


few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer.


3-14 Pre-driving checks and adjustments


LPD0078


TILT OPERATION Pull the lock lever forward and adjust the steering wheel up or down to the desired position. Release the lock lever to lock the steering wheel in place.


WARNING


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X


TELESCOPIC OPERATION Push the lever down and adjust the steering wheel forward or backward to the desired posi- tion. Pull the lock lever up firmly to lock the steering wheel in place.


WARNING


Do not adjust the steering wheel any closer to you than is necessary for proper steering operation and comfort. The driv- er(cid:146)s air bag inflates with great force. If you are unrestrained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practical from the steering wheel. Always use the seat belts.


SUN VISORS


WPD0140


WPD0141


Slide the sun visor extension (if so equipped) in or out as needed.


CAUTION


Do not store the sun visor before returning it to its original position.


VANITY MIRRORS (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is open.


Pre-driving checks and adjustments 3-15


Z REVIEW COPY:—2004 Altima (l30) Owners Manual (owners)—USA English (nna) 10/13/03—tbrooks X

Loading...
x