ously for more than 30 seconds.
c Do not operate the washer if the
reservoir tank is empty.
WIC0183
WARNING
In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the wind- shield with the defroster before you wash the windshield.
SWITCH OPERATION Push the lever down to operate the wind- shield wipers. Pull the lever toward you to operate the washer. The intermittent operation speed is as fol- lows: c When the vehicle speed is continuously low, so is the intermittent operation speed.
c When the vehicle speed is continuously high, so is the intermittent operation speed.
LO: Continuous low speed operation
LIC0170
To defog the rear window glass, start the engine and push the rear window defogger switch on. The rear window defogger indi- cator light on the switch comes on. Push the switch again to turn the defogger off. The rear window defogger switch automati- cally turns off after approximately 15 minutes.
CAUTION
When cleaning the inner side of the window, be careful not to scratch or damage the rear window defogger.
Instruments and controls 2-17
Z X
HEADLIGHT AND TURN SIGNAL SWITCH
NOTE: The top few rows of wires on the rear window are not part of the rear window defogging system. These wires make up the antenna for the audio system.
XENON HEADLIGHTS WARNING HIGH VOLTAGE
c When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at an authorized NISSAN dealer.
c Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to an authorized NISSAN dealer and have the headlights adjusted correctly.
When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize. c The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn off the headlights for short inter- vals, (for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon headlights is not reduced.
c If the xenon headlight bulb is close to burning out, the brightness will dras- tically decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above NISSAN dealer.
appear,
contact
signs
2-18 Instruments and controls
Z X
HEADLIGHT SWITCH Lighting Turn the switch to the position: The parking, rear combination, side marker, li- cense plate and instrument panel lights come on. Turn the switch to the The headlights come on and all the other lights remain on. To select the high beam function, push the lever forward. The high beam lights come on and the indicator light illuminates. Pull it back to select the low beam.
position:
WIC0184
Instruments and controls 2-19
Z X
Passing signal Pulling and releasing the lever flashes the headlight high beams on and off. Daytime running light system (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The day- time running lights operate with the head- light switch in the OFF position or in the position. Turn the headlight switch to illumination when
the driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is re- leased. The daytime running lights will re- main on until the ignition switch is turned off.
position for full
WARNING
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring your- self and others.
WIC0185
Instrument brightness control The instrument cluster illuminates when the ignition switch is in ON position. The instrument brightness control operates when the light switch is in the AUTO,
or
position.
Turn the control to adjust the brightness of instrument panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off.
2-20 Instruments and controls
LIC0135
AUTOLAMP SYSTEM (if so equipped) The autolamp system allows the headlights to be set so they turn on and off automati- cally. The autolamp system can turn on the headlights automatically when it is dark, turn off the headlights when it is light, and keep the headlights on for up to 45 seconds after you turn the key to OFF and all doors are closed. If the ignition switch is turned OFF and one of the doors is opened, the headlights re- main ON for five minutes.
Z X
To set the autolamp system: 1. Make sure the headlight switch is in the
AUTO position.
2. Turn the ignition key to ON. 3. The autolamp system automatically turns
the headlights on and off.
, or
position.
To turn the autolamp system off, turn the switch to the OFF, Be sure you do not put anything on top of the autolamp sensor located in the top driver side of the instrument panel. The autolamp sensor controls the autolamp; if it is covered, the autolamp sensor reacts as if it is dark out and the head- lights will illuminate. If this occurs while parked with the engine off and the key in the ON position, your vehicle’s battery could become discharged.
TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automati- cally. Lane change signal To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.
FOG LIGHT SWITCH (if so equipped)
LIC0173
position:
Normal operation of the fog lights in the ON Headlight switch in the AUTO position; daytime operation c Fog lights, marker and taillights come
ON.
c Headlights do not come ON. c Dash readouts dim unless the dimmer
switch is on full bright.
c If the ignition switch is in the OFF position
with the fog lights turned ON, a warning
chime will sound indicating the fog lights
Instruments and controls 2-21
Z X
To turn the fog lights OFF, turn the switch to the OFF position. The fog lights automatically turn off when- ever the high-beam headlight function is selected.
were left ON. The fog lights will be turned OFF by the Battery Saver function ap- proximately 5 minutes after the last door is closed.
c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Battery Saver function, the fog lights will immediately come back ON.
Headlight switch in the AUTO position; nighttime operation c Fog lights, marker and taillights come
ON.
c Headlights come ON. c Dash readouts dim unless the dimmer
switch is on full bright.
c If the ignition switch is in the OFF position
with the fog lights turned ON, the fog
lights will be turned OFF by the Twilight
Sentinel function approximately 45 sec-
onds after the last door is closed. When
any door is opened when the ignition
switch is in the OFF position, the Twilight
Sentinel function operates for approxi-
mately 5 minutes. After approximately 5
2-22 Instruments and controls
minutes, the lights will turn OFF due to the Battery Saver function.
c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Twilight Sentinel function, the fog lights and the headlights will come ON together when the Auto Light Sensor determines it is dark enough. The fog lights will now operate independently of the headlights only if the headlight switch is turned OFF.
c When the high-beams are turned ON, the fog lights will turn OFF. The fog lights will come back ON when the high-beams are turned OFF.
Headlights turned ON and OFF by the driver (no AUTO headlight function); day or nighttime operation c Same operation as ‘‘Headlight switch in the AUTO position; daytime operation’’ described above.
Some of the Battery Saver and Twilight Sentinel functions can be turned ON and OFF or adjusted. Please see your NISSAN dealer if you have any ques- tions.
Z X
HAZARD WARNING FLASHER SWITCH
HORN
c Do not use the switch while moving on the highway unless unusual cir- cumstances force you to drive so slowly that your vehicle might be- come a hazard to other traffic.
c Turn signals do not work when the hazard warning flasher lights are on.
The flashers can be actuated with the igni- tion switch either OFF or ON. Some state laws may prohibit the use of the hazard warning flasher switch while driving.
LIC0174
Push the switch on to warn other drivers when you must stop or park under emer- gency conditions. All turn signal lights flash.
WARNING
c If stopping for an emergency, be sure to move the vehicle well off the road.
WIC0119
To sound the horn, push the center pad area of the steering wheel.
WARNING
Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.
Instruments and controls 2-23
Z X
HEATED SEATS (if so equipped)
LIC0136
The front seats (if so equipped) are warmed by built-in heaters. The switches are located on the center console. 1. Start the engine. 2. Push the low or high position of
the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.
2-24 Instruments and controls
3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off.
CAUTION
c Do not use the seat heater for ex- tended periods or when no one is using the seat.
c Do not put anything on the seat which insulates heat, such as a blan- ket, cushion, seat cover, etc. Other- wise, the seat may become over- heated.
c Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.
c Any liquid spilled on the heated seat should be removed immediately with a dry cloth.
c When cleaning the seat, never use benzine, thinner, or any similar ma- terials.
c If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.
c The battery could run down if the heater is operated while the engine is not running.
Z X
TRACTION CONTROL SYSTEM (TCS) CANCEL SWITCH (if so equipped)
POWER OUTLET
LIC0134
LIC0142
WIC0186
To cancel the Traction Control System (TCS), push the “TCS OFF” switch to turn off the system. The indicator will come on. Push the “TCS OFF” switch again or restart the engine and the system will operate normally. See “Traction control system” in the “Starting and driving” section.
The power outlet is for powering electrical accessories such as cellular telephones.
CAUTION
c Take care as the outlet and plug may be hot during or immediately after use.
c This power outlet is not designed for
use with a cigarette lighter unit.
c Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
Instruments and controls 2-25
Z X
c Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged bat- tery.)
c Avoid using when the air conditioner, headlights or rear window defogger is on.
c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned off.
c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tempera- ture fuse may blow.
c When not in use, be sure to close the cap. Do not allow water to contact the socket.
2-26 Instruments and controls
STORAGE
LIC0016
LIC0137
SEATBACK POCKETS (if so equipped) The seatback pockets are located on the back of the driver and passenger seats. The pockets can be used to store maps. SEATBACK SIDE POCKETS (if so equipped) A seatback side pocket is located on the inboard side of the front passenger seat.
SUNGLASSES CASE The sunglasses case can be opened by pushing the button.
WARNING
The sunglasses case should not be used while driving so full attention may be given to vehicle operation.
Z X
CAUTION
c Do not use for anything other than
sunglasses.
c Do not leave sunglasses in the sun- glasses case while parking in direct sunlight. The heat may damage the sunglasses.
WIC0138
LIC0175
CUP HOLDERS To open the front cup holders, lift the con- sole cover. To close, lower the console cover. The rubber cleaning. The rear cupholders are located in the fold- down armrest in the rear seat back.
insert may be removed for
WARNING
The cup holder should not be used while driving so full attention may be given to vehicle operation.
CAUTION
c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liq- uid is hot, it can scald you or your passenger.
Instruments and controls 2-27
Z X
c Use only soft cups in the cup holder. Hard objects can injure you in an accident.
CONSOLE BOX
WARNING
The center console box should not be used while driving so full attention may be given to vehicle operation.
CAUTION
c This power socket is not designed for use with a cigarette lighter unit. c Do not use accessories that exceed 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
LIC0176
GLOVE BOX The glove box opens by pulling the handle. When locking or unlocking the glove box, use the master key. The valet key cannot be used to lock or unlock the glove box.
WARNING
Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
2-28 Instruments and controls
Z X
Upper half Pull up on the lever to open the upper half of the console box. The rubber mat may be removed for cleaning. The upper half of the console box may be used for storage of cellular phones. An access hole is provided at the bottom of the upper half of the console box for phone cord routing to the power socket. To route a phone cord to the power socket: 1. open the upper half of the console box 2. remove the rubber mat, and then remove
the cutout area from the mat
3. remove the access hole cover 4. install the rubber mat 5. route the phone cord through the access
hole and plug into the power socket
Lower half Pull up on the lever to open the lower half of the console box. A power socket is located inside the console box and there is storage for compact discs.
WIC0189
Armrest Push the button to elevate the armrest. To return armrest to regular position, push arm- rest rearward until locked.
LIC0181
COVERED STORAGE BOX Push the bottom center of the lid to open.
Instruments and controls 2-29
Z X
CARGO NET (if so equipped) The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion. To install the cargo net, attach the hooks to the retainers. To remove the cargo net, detach the hooks from the cargo net retainers.
2-30 Instruments and controls
WIC0190
Z X
WINDOWS
WARNING
POWER WINDOWS
c Properly secure all cargo to help pre-
vent it from sliding or shifting.
c Be sure to secure hooks into the retainers. The cargo restrained in the net must not exceed 30 lbs. (13.6 kg) or the net may not stay secured.
WARNING
c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before clos- ing the windows. Use the window lock switch to prevent unexpected use of the power windows.
c Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols and become trapped in a window. Unattended children could become involved in serious acci- dents.
LIC0177
If
The power windows operate when the igni-
tion key is in the ON position, or for about 45
seconds after the ignition key is turned to
the OFF position.
the driver’s or front
passenger’s door is opened during this pe-
riod of about 45 seconds, power to the
windows is cancelled. To open a window,
press down on the switch. To close a win-
dow, pull up on the switch. To stop the
opening or closing function at any time,
simply release the switch.
The driver side control panel
is equipped
with switches to open or close all of the
windows.
Instruments and controls 2-31
Z X
LIC0178
LIC0179
The front and rear passenger window switches operate only the corresponding passenger window. To open the window, press down on the switch. To close the window, pull up on the switch. Locking passenger windows When the power window lock switch on the driver side control panel is pushed in, only the driver side window can be opened or closed. Push it in again to cancel this func- tion.
2-32 Instruments and controls
Automatic operation To fully open the driver or passenger side window, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening. Auto-reverse function If the control unit detects something caught in the window as it is closing, the window will be immediately lowered. The auto-reverse function can be activated
when the window is closed by automatic operation when the ignition key is in the ON position or for 45 seconds after the ignition key is turned to the OFF position. Depending on the environment or driv- ing conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs.
WARNING
There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.
Z X
SUNROOF (if so equipped)
LIC0145
The sunroof only operates with the ignition key in the ON position. NOTE: If the battery is discharged or is discon- nected, the sunroof may not operate cor- rectly, and must be reset. From any sunroof position (full open, par- tially open, closed, partially vented and vented), push and hold the button in the forward position until the sunroof vents in the full-up position. This resets the sunroof motor memory and now the sunroof will operate correctly.
Sliding the sunroof To open the sunroof, push the switch to- ward DOWN/OPEN. To close the sunroof, push the switch to- ward UP/CLOSE. Tilting the sunroof Close the sunroof by pushing the switch toward UP/CLOSE. Release the switch, then push the UP/CLOSE switch to tilt the sunroof up. To tilt the sunroof down, push the switch toward DOWN/OPEN. Sun shade Open and close the sun shade by sliding it forward or backward.
WARNING
c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.
c Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is clos- ing.
CAUTION
c Remove water drops, snow,
ice or sand from the sunroof before opening. c Do not place heavy objects on the
sunroof or surrounding area.
Instruments and controls 2-33
Z X
INTERIOR LIGHT
MAP LIGHTS
−remain on for a maximum of 30
seconds.
−driver’s door is opened.
−remain on for a maximum of 30
seconds after driver’s door is closed.
−ignition key is removed from key
cylinder
−remain on for a maximum of 30
seconds.
The lights will go off when the ignition key is in the ON position, or the driver’s door is closed and locked. The lights will also go off after 10 minutes while doors are open. c When the switch is in the ON position, the interior light illuminates, whether any door is open or closed.
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
IC1235M
The interior light operates regardless of ignition key position. The interior light has a three-position switch. c When the switch is in the OFF position, the interior light does not illuminate, re- gardless of door position.
c When the switch is in the center j position, the front and rear personal lights will illuminate under the following conditions:
−driver’s door is unlocked.
2-34 Instruments and controls
Z X
LIC0147
LIC0146
To turn on the map lights, press the switches. To turn them off, press the switches again.
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
TRUNK LIGHT
The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off.
HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped) The HomeLinkT Universal Transceiver pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: c Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
c Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLinkT will retain all pro- gramming.
If
Once the HomeLinkT Universal Trans- ceiver is programmed, retain the original transmitter for future programming pro- cedures (i.e., new vehicle purchases). Upon sale of the pro- grammed HomeLinkT Universal Trans- ceiver buttons should be erased for se- curity additional information refer to ‘‘Programming the HomeLinkT Universal Transceiver’’ later in this section.
the vehicle,
purposes.
For
Instruments and controls 2-35
Z X
WARNING
c Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by fed- eral safety standards. (These stan- dards became effective for opener models manufactured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then au- tomatically stop and reverse, does not meet current federal safety stan- dards. Using a garage door opener without these features increases the risk of serious injury or death.
c During programming, your garage door or gate may open or close. Make sure that people and objects are clear of the garage door or gate that you are programming.
c Your vehicle’s engine should be turned off while programming the HomeLinkT Universal Transceiver.
2-36 Instruments and controls
SPA0609A
PROGRAMMING HomeLinkT 1. With the ignition key in the OFF position, press and hold the two outside buttons, and release when the indicator light be- gins to flash (approximately 20 seconds). This procedure erases the factory set default codes and does not have to be followed when programming additional hand-held transmitters.
2. Hold the end of the hand-held transmitter (from the device you wish to train) ap- proximately 2 to 5 inches (50 to 127 mm) away from the surface of HomeLinkT keeping the indicator light in view.
3. Using both hands, simultaneously push the hand-held transmitter button and the de- sired HomeLinkT button. Do not release the buttons until step 4 has been completed.
NOTE: Some garage door openers may require the procedures noted under ‘‘Canadian Programming’’. 4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing light indicates the HomeLinkT Universal Trans- ceiver has been successfully programmed. To program the remaining two buttons, fol- low steps 2 through 4. If, after repeated attempts, you do not suc- cessfully program the HomeLinkT Universal Transceiver to learn the signal of the hand- held transmitter, refer to ‘‘Rolling Code Pro- gramming’’ later in this section. PROGRAMMING HomeLinkT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand-held transmitters to stop transmitting after 2 seconds. To program your hand-held transmitter to HomeLinkT, continue to press
Z X
and hold the HomeLinkT button (note step 2
through 4 under ‘‘Programming HomeLinkT’’)
while you press and re-press (‘‘cycle’’) your
hand-held transmitters every 2 seconds until
the indicator light flashes rapidly (indicating
successful programming).
NOTE:
If programming a garage door opener, etc.,
it is advised to unplug the device during the
‘‘cycling’’ process to prevent possible dam-
age to the garage door opener components.
OPERATING THE HomeLinkT
UNIVERSAL TRANSCEIVER
The HomeLinkT Universal Transceiver (once
programmed) may now be used to activate the
garage door, etc. To operate, simply press the
appropriate programmed HomeLinkT Universal
Transceiver button. The red indicator light will
illuminate while the signal is being transmitted.
PROGRAMMING TROUBLE-
DIAGNOSIS
If the HomeLinkT does not quickly learn the
hand-held transmitter information:
c replace the hand-held transmitter batter-
ies with new batteries.
c position the hand-help transmitter with its battery area facing away from the HomeLinkT surface.
c press and hold both the HomeLinkT and hand-held transmitter buttons without in- terruption.
c position the hand-held transmitter 2 to 5
inches (50 to 127 mm) away from the
HomeLinkT surface. Hold the transmitter
in that position for up to 15 seconds. If
HomeLinkT is not programmed within
that time, try holding the transmitter in
another position - keeping the indicator
light in view at all times.
If you continue to have programming diffi- culties, please contact the NISSAN Con- sumer Affairs Department. The phone num- bers are located in the Foreword of this owner’s manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared, how- ever to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds)
ROLLING CODE PROGRAMMING Rolling code garage door openers (or other rolling code devices) which are ‘‘code pro- tected’’ and manufactured after 1996, may be determined by the following: A. Reference the garage door opener Own-
er’s Manual for verification.
B. The hand-held transmitter appears to program the HomeLinkT Universal Transceiver but does not activate the garage door.
C. Press and hold the trained HomeLinkT button. If the garage door opener has the rolling code feature, the HomeLinkT indi- cator light will flash rapidly, then remains on after 2 seconds.
To program the HomeLinkT Universal
Transceiver to a garage door opener with
the rolling code feature, follow these instruc-
tions after completing the ‘‘Programming
HomeLinkT’’ (the aid of a second person
may make the following procedures quicker
and easier).
1. Locate the training button on the garage
door opener motor unit. Exact location
the button may vary by
and color of
Instruments and controls 2-37
Z X
there is garage door opener brand. difficulty locating the training button, ref- erence the garage door opener Owner’s Manual.
If
2. Press the training button on the garage door opener motor unit (which may acti- vate a training light).
NOTE: Following step 2, there are 30 seconds in which to initiate step 3. 3. Firmly press and release the pro- grammed HomeLinkT button. Press and release the HomeLinkT button a second time to complete the training process. (Some garage door openers may require you to do this procedure a third time to complete the training.)
The garage door opener should now recog- nize the HomeLinkT Universal Transceiver and activate when the HomeLinkT button is pressed. The remaining two buttons may now be programmed (if not yet pro- grammed, follow steps 2 through 4 in the ‘‘Programming HomeLinkT’’ procedures earlier in this section).
2-38 Instruments and controls
REPROGRAMMING A SINGLE HomeLinkT BUTTON To reprogram an HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT button. Do not release the button until step 4 has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 2 to 5 inches (50 to 127 mm) away from the HomeLinkT sur- face.
3. Press and hold the hand-held transmitter
button.
4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLinkT Universal Transceiver but- ton has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just pro- grammed. This procedure will not affect any other programmed HomeLinkT buttons.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change
the codes of any non-rolling code device
that has been programmed into HomeLinkT.
Consult the Owner’s Manual of each device
or call the manufacturer or dealer of those
devices for additional information.
When your vehicle is recovered, you will
need to reprogram the HomeLinkT Uni-
versal Transceiver with your new trans-
mitter information.
FCC Notice:
This device complies with FCC rules part
15. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference and (2) This
device must accept any interference that
may be received, including interference
that may cause undesired operation.
This transmitter has been tested and
complies with FCC and DOC/MDC rules.
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s author-
ity to operate the device.
DOC: ISTC 1763K1313
FCC I.D. CV2V67690
Z X
3 Pre-driving checks and adjustments
Keys .......................................................................3-2
Nissan vehicle immobilizer system
(NVIS) keys .......................................................3-2
Doors......................................................................3-2
Locking with key................................................3-3
Locking with inside lock knob............................3-3
Locking with power door lock switch.................3-4
Child safety rear door lock ................................3-4
Remote keyless entry system (if so equipped)......3-5
How to use remote keyless entry
system ...............................................................3-5
Battery replacement ..........................................3-8
Hood.......................................................................3-9
Trunk lid................................................................3-10
Opener operation ............................................3-10
Key operation ..................................................3-11
Interior trunk lid release...................................3-11
Fuel filler lid..........................................................3-12
Opener operation ............................................3-12
Fuel filler cap...................................................3-12
Steering wheel .....................................................3-13
Tilt operation....................................................3-13
Telescopic operation .......................................3-14
Sun visors.............................................................3-14
Vanity mirrors ..................................................3-14
Mirrors ..................................................................3-15
Inside mirror.....................................................3-15
Automatic anti-glare inside mirror
(if so equipped)................................................3-15
Outside mirror remote control .........................3-16
Z X
KEYS
DOORS
WPD0013
NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) KEYS You can only drive your vehicle using the master or valet keys which are registered to the Nissan Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. The master key can be used for all the locks. The valet key cannot be used for the trunk lid glove box lock or rear seatback lock. To protect belongings when you leave a key with someone, give them the valet key only. 3-2 Pre-driving checks and adjustments
WARNING
c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.
c Before opening any door, always look for and avoid oncoming traffic. c Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.
Never leave these keys in the vehicle. Record the key number on the key number plate supplied with your keys and keep it in a safe place (such as your wallet), not in the vehicle. NISSAN does not record any key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer. Nissan Vehicle Immobilizer System KEY - Master and Valet keys: The key number is necessary when you need extra Nissan Vehicle Immobilizer Sys- tem keys. As many as 5 Nissan Vehicle Immoblizer System keys can be used with one vehicle. New keys must be registered to the Nissan Vehicle Immoblizer System components in your vehicle by your NISSAN dealer. At this time, you should bring all Nissan Vehicle Immobilizer System keys that you have to your NISSAN dealer for registration. This is because the regis- tration process will erase all memory of the Nissan Vehicle Immobilizer System compo- nents.
Z X
Opening and closing windows The driver’s door key operation allows you to open and close the front door windows simultaneously. c To open the windows, turn the driver’s door key to the rear of the vehicle for longer than 1 second after the door is unlocked.
c To close the windows, turn the driver’s door key to the front of the vehicle for longer than 1 second after the door is locked.
The door windows will open or close while turning the driver’s door key. This function will operate for 45 seconds after the ignition switch is turned off unless either front door is opened.
LPD0067
LOCKING WITH KEY The power door lock system allows you to lock or unlock all doors simultaneously. Turning the front door key to the front of the vehicle locks all doors. Turning the front door key one time to the rear of the vehicle unlocks the corresponding door. From that position, returning the key to neutral (where the key can only be removed and inserted) and turning it to the rear again within 5 seconds unlocks all doors.
LPD0068
LOCKING WITH INSIDE LOCK KNOB To lock a door without the key, move the inside lock knob to the lock position. When locking a door this way, be certain not to leave the key inside the vehicle.
Pre-driving checks and adjustments 3-3
Z X
LPD0069
LPD0070
APD1010
LOCKING WITH POWER DOOR LOCK SWITCH To lock all the doors without a key, push the door lock switch (driver or front passenger side), to the lock position. When locking the door this way, be certain not to leave the key inside the vehicle. When the power door lock switch (driver or passenger side) is moved to the lock posi- tion with the key in the ignition and any door open, all doors will lock and then unlock automatically.
3-4 Pre-driving checks and adjustments
CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.
Z X
REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
It is possible to lock/unlock all doors, turn the interior light on and activate the panic alarm by using the remote controller from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors. The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends on the con- ditions around the vehicle. As many as five keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact an authorized NISSAN dealer.
CAUTION
Listed below are conditions or occur- rences which will damage the keyfob: c Do not allow the keyfob to become
wet.
c Do not drop the keyfob. c Do not strike the keyfob sharply
against another object.
c Do not place the keyfob for an ex- tended period in an area where tem- peratures exceed 140°F (60°C).
HOW TO USE REMOTE KEY- LESS ENTRY SYSTEM Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close all doors.
All of the doors will lock when the button on the keyfob is pushed even though a door remains open. If the doors are locked while any door is open, the horn beep feature will not function. 4. Push the
button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.
c When the
button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a
that
the doors are already
reminder locked. The horn may or may not beep once. Refer to ‘‘Silencing the horn beep fea- ture’’ later in this section for details.
Pre-driving checks and adjustments 3-5
Z X
The trunk lid will not open with the trunk lid release cancel switch turned to OFF. See “Trunk lid” later in this section for cancel switch. It can be opened only with the key. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the alarm to call attention as follows: 1. Push and hold the PANIC button on the
keyfob for longer than 0.5 seconds.
2. The theft warning alarm and headlights
will stay on for 25 seconds.
3. The panic alarm stops when: c it has run for 25 seconds, or c any button is pressed on the keyfob.
2. Push the UNLOCK button on the keyfob
again within 5 seconds.
c All doors unlock c The hazard indicator flashes once if all
doors are completely closed.
If the following operation is not carried out within 1 minute after pressing the “UNLOCK” button, all doors will be locked automatically. c When any door is not opened. c When the ignition key is not set in the
ON position.
The interior light can be turned off without waiting for 30 seconds by turning the igni- tion switch to the ON position or by locking the doors with the keyfob. Releasing the trunk lid 1. Push the trunk button on the keyfob for longer than 0.5 second. The trunk re- lease button on the keyfob will not oper- ate when the ignition switch is in the ON position.
2. The trunk lid opens.
LPD0071
Unlocking doors 1. Push the UNLOCK button on the keyfob
once.
c Only the driver’s door unlocks c The hazard indicator flashes once if all doors are completely closed with the ignition key in any position except the ON position.
c The interior light turns on and the light timer activates for 30 seconds when the switch is in the center j position with the ignition key in any position except the ON position.
3-6 Pre-driving checks and adjustments
Z X
LIC0168
Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the keyfob. The instruc- tions are on the back of the keyfob. To deactivate: Press and hold the
and
buttons for at least two seconds.
The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the
and two seconds
buttons for at
least
once more.
The hazard lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered. Using the interior light The interior light can be turned off without waiting 30 seconds by inserting the key into the ignition or locking the doors with the multi-remote controller or pushing the inte- rior light button to OFF. Opening windows (if so equipped) The keyfob allows you to open the front windows simultaneously. c To open the front windows, press the UNLOCK button on the keyfob for longer than 3 seconds after the door is un- locked.
The door windows will open while pressing the UNLOCK button on the keyfob. This function will operate for 45 seconds after the ignition switch is turned off unless either front door is opened. This opening windows function of the key- fob can be suspended using a CONSULT-II
diagnostic tool. Please contact an autho- rized NISSAN dealer. The door windows cannot be closed by using the keyfob.
Pre-driving checks and adjustments 3-7
Z X
keyfob operation. Each time the hazard lights flash once.
button is pressed, the
If the battery is removed for any reason other than replacement, perform step 4. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.
c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.
FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not
Z X
BATTERY REPLACEMENT Replace the battery in the keyfob as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one.
3-8 Pre-driving checks and adjustments
LPD0081
Recommended battery: Sanyo CR2025
or equivalent.
3. Close the lid securely. 4. Press the
but- ton two or three times to check the
button, then the
HOOD
cause harmful interference, and (2) this device must accept any interference re- ceived including interference that may cause undesired operation of the device.
1. Pull
the hood lock release handle s1
located below the driver side instrument
panel; the hood springs up slightly.
2. Lift the lever s2 at the front of the hood with your fingertips and raise the hood.
3. Remove the support rod s3
from the
clamp.
4. Insert the support rod s4 into the slot on
the passenger side fender ledge.
5. When closing the hood, return the sup-
LPD0072
Pre-driving checks and adjustments 3-9
Z X
port rod to its original position, lower the hood to approximately 12 inches above the latch and release it. This allows proper engagement of the hood latch.
WARNING
c Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.
c If you see steam or smoke coming to
from the engine compartment, avoid injury do not open the hood.
TRUNK LID
WPD0105
OPENER OPERATION WARNING
c Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See ‘‘Exhaust gas’’ in the ‘‘Starting and driving’’ section of this manual.
c Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the trunk closed, when not in use, and prevent children’s access to car keys.
The trunk lid opener lever is located below the armrest of the driver’s door trim panel. To open the trunk lid, pull the opener lever out. To close the trunk lid, lower and push the trunk lid down securely.
3-10 Pre-driving checks and adjustments
Z X
LPD0085
Cancel switch When the cancel switch located inside the glove box is OFF, the trunk lid cannot be opened with the trunk lid release switch or valet key. It can be opened with the master key or keyfob.
LPD0074
KEY OPERATION To open the trunk lid, turn the key clock- wise. To close the trunk lid, lower and push the trunk lid down securely.
LPD0075
INTERIOR TRUNK LID RELEASE
WARNING
Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the trunk lid closed, when not in use, and prevent children’s access to car keys.
The interior trunk lid release mechanism provides a means of escape for children and adults in the event they become locked inside the trunk.
Pre-driving checks and adjustments 3-11
Z X
To open the trunk from the inside, rotate the illuminated lever until the lock releases and push up on the trunk lid. The release lever is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located inside the trunk com- partment on the trunk lock at the center of the trunk lid.
FUEL FILLER LID
WARNING
c Gasoline is extremely flammable and highly explosive under certain con- ditions. You could be burned or se- riously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
c Fuel may be under pressure. Turn the cap one-half turn, and wait for any ‘‘hissing’’ sound to stop to prevent fuel from spraying out and possible personal injury. Then remove the cap. c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refuel- ing may cause fuel overflow, result- ing in fuel spray and possibly fire.
c Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An in- correct cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator lamp to come on.
LPD0076
OPENER OPERATION The fuel filler lid opener lever is located on the outside of the driver’s seat. To open the fuel filler lid, pull the opener lever up. To lock, close the fuel filler lid securely. FUEL FILLER CAP The fuel filler cap is a ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard.
3-12 Pre-driving checks and adjustments
Z X
mal- properly may cause the function indicator lamp (MIL) to illu- minate. If the lamp illuminates because the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.
c For additional information, see the “Malfunction indicator lamp (MIL)’’ in the “Instrument and controls” section earlier in this manual.
c Do not fill a portable fuel container in the vehicle or trailer. Static electric- ity can cause an explosion of flam- mable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when fill- ing portable fuel containers: — Always the place container on the
ground when filling.
— Do not use electronic devices
while filling.
— Keep the pump nozzle in contact with the container while you are filling it.
— Use only approved portable fuel
containers for flammable liquid.
c Never pour fuel into the throttle body
to attempt to start your vehicle.
CAUTION
c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.
c Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap
STEERING WHEEL
LPD0078
TILT OPERATION Pull the lock lever forward and adjust the steering wheel up or down to the desired position. Release the lock lever to lock the steering wheel in place.
WARNING
Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.
Pre-driving checks and adjustments 3-13
Z X
SUN VISORS
LPD0002
WPD0015
CAUTION
Do not store the main sun visor before storing the extension sun visor.
VANITY MIRRORS To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is opened.
TELESCOPIC OPERATION Push the lever down and adjust the steering wheel forward or backward to the desired position. Pull steering wheel in place.
the lock lever up firmly to lock the
WARNING
Do not adjust the steering wheel any closer to you than is necessary for proper steering operation and comfort. The driver’s air bag inflates with great force. If you are unrestrained, leaning forward, sitting sideways or out of po- sition in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practical from the steering wheel. Al- ways use the seat belts.
3-14 Pre-driving checks and adjustments
Z X
MIRRORS
apply glass cleaner. Doing so will reduce the sensitivity of the sensor, resulting in improper operation.
PD1006M
LPD0086
INSIDE MIRROR The night position reduces glare from the headlights of vehicles behind you at night.
WARNING
Use the night position only when nec- essary, because it reduces rear view clarity.
AUTOMATIC ANTI-GLARE IN- SIDE MIRROR (if so equipped) The inside mirror is designed so that it automatically changes reflection according to the intensity of the headlight of the follow- ing vehicle. When the inside mirror switch is in the AUTO position, excessive glare from the headlights of the vehicle behind you will be reduced. When the switch of the inside mirror is in the OFF position, the inside mirror will operate normally. Do not hang any object on the sensor or
Pre-driving checks and adjustments 3-15
Z X
WARNING
Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mir- ror or glance over your shoulder to properly judge distances to other ob- jects.
LPD0065
OUTSIDE MIRROR REMOTE CONTROL The outside mirror remote control only op- erates when the ignition switch is in the ACC or ON position. Rotate the control lever to select the right or left mirror. Adjust the mirror to the desired position by moving the control lever.
3-16 Pre-driving checks and adjustments
Z X
4 Heater, air conditioner and audio systems
Ventilators ..............................................................4-2
Center ventilators ..............................................4-2
Side ventilators..................................................4-2
Heater and air conditioner (manual) ......................4-3
Controls .............................................................4-3
Heater operation................................................4-4
Air conditioner operation (if so
equipped)...........................................................4-5
Air flow charts....................................................4-6
Heater and air conditioner (automatic) (if so
equipped) ...............................................................4-9
Automatic operation ..........................................4-9
Manual operation.............................................4-10
Operating tips ..................................................4-11
Servicing air conditioner.......................................4-11
Audio system........................................................4-12
Radio ...............................................................4-12
FM radio reception ..........................................4-12
AM radio reception ..........................................4-12
Audio operation precautions ...........................4-13
FM-AM radio with compact disc (CD)
player...............................................................4-16
FM-AM radio with compact disc (CD)
changer (if so equipped) .................................4-21
CD care and cleaning......................................4-28
Steering wheel switch for audio control
(if so equipped)................................................4-28
Antenna ...........................................................4-29
Car phone or CB radio.........................................4-29
Z X
VENTILATORS
LHA0107
LHA0108
WHA0135
CENTER VENTILATORS Adjust air flow direction by moving the ven- tilator slide.
SIDE VENTILATORS You can open or close the side ventilators by using the dial located at the side of the ventilators. Adjust air flow direction by mov- ing the ventilator slide. The airflow can be turned off by turning the dial to the outboard position.
4-2 Heater, air conditioner and audio systems
Z X
HEATER AND AIR CONDITIONER (MANUAL)
WARNING
c The air conditioner cooling function operates only when the engine is running.
c Do not leave children, impaired adults, or pets alone in your vehicle. On hot sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.
c Positioning of the heating or air con- ditioning controls should not be done while driving, so full attention may be given to vehicle operation.
— Air flows from defroster outlets
and foot outlets.
— Air flows mainly from defroster
outlets.
Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air.
Air recirculation button Off position (Indicator light off): Outside air is drawn into the passenger compartment and distributed through the selected outlet. Use the off position for normal heater or air conditioner operation. On position (Indicator light on): Interior air is recirculated inside the vehicle. Push the button to the on position when: c driving on a dusty road. c to avoid traffic fumes.
LHA0109
turns the fan on and off, and
CONTROLS Fan control dial This dial controls fan speed. Air control dial These dials allow you to select the air flow outlets.
— Air flows from center and side
ventilators.
— Air flows from center and side
ventilators and foot outlets.
— Air flows mainly from foot outlets.
Heater, air conditioner and audio systems 4-3
Z X
c for maximum cooling when using the air
conditioner
Air conditioner button (if so equipped) This button is provided only on vehicles equipped with an air conditioner. Start the engine, turn the fan control dial to the desired (1 to 4) position and push the A/C button to turn on the air conditioner. The indicator light comes on when the air conditioner is operating. To stop the air conditioner, push the switch again. The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defroster outlets. 1. Push the
button to the off position
for normal heating.
2. Turn the air control dial to the position. 3. Move the fan control dial to the desired
position.
4. Move the temperature control dial to the desired position between the middle and the HOT position.
Ventilation This mode directs outside air to the side and center ventilators. 1. Turn the air control dial to the
po-
sition.
2. Push the 3. Move the fan control dial to the desired
button in.
position.
4. Move the temperature control dial to the
desired position.
Defrosting or defogging This mode is used to defrost/defog the windows. 1. Turn the air control dial to the position. 2. Move the fan control dial to the desired
position.
3. Move the temperature control dial to the desired position between the middle and the HOT position.
c To quickly remove ice or fog from the
windows, turn on the fan control dial to 4
and the temperature control dial to the
full HOT position.
c When the
position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate). This dehumidifies the air which helps defog the windshield. The air recir- culation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps de- fog the windshield.
Bi-level heating/cooling This mode directs air from the side, center and foot outlets. 1. Push the button to the off position. 2. Turn the air control dial to the position. 3. Move the fan control dial to the desired
position.
4. Move the temperature control dial to the
desired position.
Heating and defogging This mode heats the interior and defogs the windshield. 1. Turn the air control dial to the
position.
4-4 Heater, air conditioner and audio systems
Z X
2. Move the fan control dial to the desired
position.
3. Move the temperature control dial to the desired position between the middle and the HOT position.
Operating tips c Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater op- eration.
c When the
or
positions are selected, the air recirculation mode auto- matically turns off. Outside air is drawn into the passenger compartment to improve the defogging performance.
AIR CONDITIONER OPERATION (if so equipped) Start the engine, move the fan control dial to the desired (1 to 4) position and push in the A/C button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function op- erates only when the engine is running.
Cooling This mode is used to cool and dehumidify the air. 1. Push the 2. Turn the air control dial to the
button to the off position. po-
sition.
3. Move the fan control dial to the desired
position.
4. Push on the air conditioner button. The
indicator light comes on.
5. Move the temperature control dial to the
desired position.
c For quick cooling when the outside tem- perature is high, push the button to the on position (Indicator light on). Be sure to return the button to the off position for normal cooling.
Dehumidified heating This mode is used to heat and dehumidify. 1. Push the button to the off position. 2. Turn the air control dial to the po-
sition.
3. Move the fan control dial to the desired
position.
4. Push on the air conditioner button. The
indicator light comes on.
5. Move the temperature control dial to the
desired position.
Dehumidified defogging This mode defogs the windows and dehu- midifies the air. 1. Turn the air control dial to the
posi-
tion. When the position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate). This dehumidifies the air which helps defog the windshield. The air recir- culation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps de- fog the windshield.
2. Move the fan control dial to the desired
position.
3. Move the temperature control dial to the
desired position.
Outside air is drawn into the passenger compartment to improve the defogging per- formance.
Heater, air conditioner and audio systems 4-5
Z X
Operating tips c Keep the windows and sun roof closed while the air conditioner is in operation. c After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.
c The air conditioner system should be operated for approximately ten min- utes at least once a month. This helps prevent damage to the system due to lack of lubrication.
c If the engine coolant temperature gauge