2002 Nissan Altima Owners Manual

Front facing When you install a child restraint in the rear seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing direction, depending on the size of the child. Al- ways follow the restraint manufacturer’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

Seats, restraints and supplemental air bag systems 1-31

Z X

SSS0107

SSS0062

SSS0108

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.

4. Allow the seat belt to retract. Pull up on the seat belt to remove any slack in the belt.

1-32 Seats, restraints and supplemental air bag systems

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that is securely held in place.

it

6. Check that the retractor is in the auto- matic locking mode by trying to pull more seat belt out of the retractor. If you can- not pull any more belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure that the child re- straint is properly secured prior to each

Z X

use. If the belt is not locked, repeat steps three through six.

After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled.

SSS0155

WRS0009

Rear facing When you install a child restraint in the rear seat, follow these steps: 1. Position the child restraint on the seat. The direction of the child restraint de- pends on the type of the child restraint and the size of the child. Always follow the restraint manufacturer’s instructions.

Seats, restraints and supplemental air bag systems 1-33

Z X

SSS0046

WRS0010

SSS0109

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted.

4. Allow the seat belt to retract. Pull up on the seat belt to remove any slack in the belt.

1-34 Seats, restraints and supplemental air bag systems

Z X

LATCH (LOWER ANCHORS AND TETHER FOR CHILDREN) SYSTEM

use. If the belt is not locked, repeat steps three through six.

After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt only locks during a sudden stop or impact.

SSS0110

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that is securely held in place.

it

6. Check that the retractor is in the auto- matic locking mode by trying to pull more seat belt out of the retractor. If you can- not pull any more seat belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure that the child re- straint is properly secured prior to each

LRS0117

WARNING

c Attach LATCH system compatible child restraints only at the locations shown. If a child restraint is not se- cured properly, your child could be seriously injured or killed in an acci- dent.

c Do not secure a child restraint in the center rear seating position using the LATCH system anchors. The child restraint will not be secured properly.

Seats, restraints and supplemental air bag systems 1-35

Z X

c The LATCH system anchors are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstance are they to be used for adult seat belts or harnesses.

The LATCH system anchors are located at the rear of the seat cushion near the seat- back. A label is attached to the seat back to help you locate the LATCH system anchors. LATCH child restraints generally require the use of a top tether strap. See ‘‘Top Tether Strap Child Restraint’’ later in this section for installation instructions. When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. When you install a LATCH system compat- ible child restraint to the lower anchor at- tachments in the rear seat, follow these steps:

WARNING

Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LATCH system anchors, such as seat belt webbing or seat cushion material. The child re- straint will not be secured properly if the LATCH system anchors are ob- structed.

Some child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle. This sys- tem is known as the LATCH (Lower An- chors and Tether for Children) system. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not have to use a vehicle seat belt to secure the child re- straint. Your vehicle is equipped with spe- cial anchor points that are used with LATCH system compatible child restraints. Check your child restraint for a label stating that it is compatible with the LATCH system. This information may also be in the child restraint owner’s manual. If you have such a child restraint, refer to the illustration for the rear seating positions equipped with LATCH system anchors which can be used to se- cure the child restraint. 1-36 Seats, restraints and supplemental air bag systems

1. To install the LATCH system compatible child restraint, insert the child restraint LATCH system anchor attachments into the anchor points on the rear seat. If the child restraint is equipped with a top tether, see ‘‘Top Tether Strap Child Re- straint’’ later in this section for installation instructions.

2. After attaching the child restraint and before placing the child in it, use force to tilt the child restraint from side to side and tug it forward to make sure that the child restraint is securely held in place.

3. Check to make sure that the child re- straint is properly secured prior to each use.

Z X

WARNING

Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.

Anchor point locations Anchor points are located on the rear parcel shelf finisher. If you have any questions when install- ing a top strap child restraint on the rear seat, consult your NISSAN dealer for details.

LRS0108

TOP TETHER STRAP CHILD RE- STRAINT If your child restraint has a top tether strap, it must be secured to the provided anchor point. First, secure the child restraint with the rear seat belt. Flip up the anchor cover from the anchor point which is located directly behind the child seat. Secure the top tether strap to the anchor bracket. Tighten the strap to remove any slack according to the manufacturer instruc- tions for the child restraint.

Seats, restraints and supplemental air bag systems 1-37

Z X

c The three-point seat belt in your ve- hicle is equipped with a locking mode retractor which must be used when installing a child restraint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

INSTALLATION ON FRONT PAS- SENGER SEAT

WARNING

c Never install a rear-facing child re- straint in the front passenger seat. Supplemental front air bags inflate with great force. A rear-facing child restraint could be struck by the supplemental front air bag in a crash and could seriously injure or kill your child.

ARS1135

if you must

c NISSAN recommends that child re- straints be installed in the rear seat. However, install a forward-facing child restraint in the front passenger seat, move the pas- senger seat to the rear most posi- tion.

c A child restraint with a top tether strap should not be used in the front passenger seat.

1-38 Seats, restraints and supplemental air bag systems

Z X

WRS0019

ARS1073

ARS1034

If you must install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a forward-facing direction only. Move the seat to the rear most position. Always follow the child restraint manufacturer’s instructions. Child restraints for infants must be used in the rear-facing direc- tion and therefore must not be used in the front seat.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the seat belt is fully retracted.

Seats, restraints and supplemental air bag systems 1-39

Z X

After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is can- celed.

ARS1074

ARS1079

4. Allow the seat belt to retract. Pull up on the seat belt to remove any slack in the belt.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more seat belt out of the retractor. If you can- not pull any more belt webbing out of the retractor, the seat belt is in the automatic locking mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the lap belt locked, repeat steps 3
through 6.

is not

1-40 Seats, restraints and supplemental air bag systems

Z X

MEMO

Seats, restraints and supplemental air bag systems 1-41

Z X

2 Instruments and controls

Instrument panel ....................................................2-2
Meters and gauges ................................................2-3
Speedometer and odometer .............................2-3
Trip computer ....................................................2-3
Tachometer........................................................2-6
Engine coolant temperature gauge...................2-6
Fuel gauge ........................................................2-7

Warning/indicator lights and audible reminders................................................................2-8
Checking bulbs..................................................2-8
Warning lights....................................................2-8
Indicator lights .................................................2-11
Audible reminders............................................2-12
Security systems ..................................................2-13

Nissan vehicle immobilizer system (NVIS)..............................................................2-13
Vehicle security system (if so equipped) ........2-14
Windshield wiper and washer switch...................2-17
Switch operation..............................................2-17
Rear window defogger switch..............................2-17
Headlight and turn signal switch..........................2-18
Xenon headlights.............................................2-18

Headlight switch ..............................................2-19
Autolamp system (if so equipped)...................2-20
Turn signal switch............................................2-21
Fog light switch (if so equipped)..........................2-21
Hazard warning flasher switch.............................2-23
Horn......................................................................2-23
Heated seats (if so equipped)..............................2-24
Traction control system (TCS) cancel switch (if so equipped) ....................................................2-25
Power outlet .......................................................2-25
Storage.................................................................2-26
Seatback pockets (if so equipped)..................2-26
Seatback side pockets (if so equipped)..........2-26
Sunglasses case .............................................2-26
Cup holders .....................................................2-27
Glove box ........................................................2-28
Console box ....................................................2-28
Covered storage box.......................................2-29
Cargo net (if so equipped) ..............................2-30
Windows...............................................................2-31
Power windows................................................2-31
Sunroof (if so equipped).......................................2-33

Z X

Interior light...........................................................2-34
Map lights.............................................................2-34
Trunk light.............................................................2-35
HomeLinkT universal transceiver (if so equipped) .............................................................2-35
Programming HomeLinkT................................2-36
Programming HomeLinkT for Canadian customers ........................................................2-36

Operating the HomeLinkT universal transceiver .......................................................2-37
Programming trouble-diagnosis.......................2-37
Clearing the programmed information.............2-37
Rolling code programming ..............................2-37
Reprogramming a single HomeLinkT button...............................................................2-38
If your vehicle is stolen....................................2-38

Z X

INSTRUMENT PANEL

2-2 Instruments and controls

1. Headlight and turn signal switch 2. Meters and gauges 3. Windshield wiper/washer switch 4. Center ventilator 5. Audio system 6. Front passenger supplemental air bag 7. Glove box 8. Heater and air conditioner 9. Hazard warning flasher switch 10. Power point 11. Rear window defogger switch 12. Cruise control main/set switch 13. Driver supplemental air bag 14. Steering wheel switch for audio control 15. Tilt/telescopic steering wheel lever 16. Traction control system (TLS) cancel

switch

17. Instrument brightness control 18. Outside mirror remote control

LIC0161

Z X

METERS AND GAUGES

The odometer records the total distance the vehicle has been driven. The twin trip odometer records the distance of individual trips.

LIC0162

SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MP/H) and kilometers per hour (km/h). Odometer/Twin trip odometer The odometer/twin trip odometer are dis- played when the igntion key is in the ON position.

WIC0182

Changing the display: Pushing the change button changes the display as follows: TRIP A ! TRIP B ! Outside temperature ! Distance to Empty ! Average economy ! Average speed ! Elapsed time ! Trip A Resetting the trip odometer: Pushing the change button for more than 1
second resets the trip odometer to zero. TRIP COMPUTER The display of the trip computer is situated Instruments and controls 2-3

Z X

in the speedometer display. When the igni- tion is turned to ON, the display scrolls all the modes of the trip computer and then shows the mode chosen before the ignition switch is turned OFF. If the battery terminal is disconnected, push the trip computer mode switch more than 1 second to activate the com- puter.

WIC0159

When the ignition switch is turned to ON, modes of the trip computer can be selected by pushing the trip mode switch on the steering wheel switch for audio controls or by the trip computer change button. The following modes can be selected: Outside air temperature (ICY–°F or °C) The outside air temperature is displayed in °F or °C. The outside air temperature mode includes a low temperature warning feature: below 37°F (3°C), temperature

the outside air

2-4 Instruments and controls

mode is automatically selected and ICY will illuminate in order to draw the driver’s atten- tion. Press the mode switch if you wish to return to the mode that was selected before the warning occurred. The ICY indicator will continue blinking as long as the tempera- ture remains below 39°F (4°C). The ambient temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind direc- tions and other driving conditions. The dis- play may differ from the actual ambient temperature or the temperature displayed on various signs or billboards. Distance to empty (dte–mile or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. The dte mode inlcudes a low range warning feature: when the fuel level is low, the dte mode is automatically selected and the dig- its blink in order to draw the driver’s atten- tion. Press the mode switch if you wish to

Z X

return to the mode that was selected before the warning occurred. The dte mark (dte) will remain blinking until the vehicle is refu- elled. When the fuel level drops even lower, the dte display will change to (----). NOTE: c If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may continue to be displayed.

c When driving uphill or

rounding curves, the fuel in the tank shifts, which may momentairly change the display.

Average fuel consumption (Mpg or l/100km) The Average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pressing the mode switch for more than approximately 1
second. The display is updated every 30
seconds. At about the first 1/3 miles (500 m) after a reset, the display shows (----).

Average speed (MPH or km/h) The average speed mode shows the aver- age vehicle speed since last reset. Reset- ting is done by pressing the mode switch for more than approximately 1 minute. The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows (----). Journey time The journey time mode shows the time since the last reset. The displayed time can be reset by pressing the mode switch for more than approximately 1 second. NOTE: If a low temperature warning and low range warning occur simultaneously, other display modes switch automati- cally to the outside temperature display. When the mode switch is pushed, the display switches to the mode chosen before the warning display, and the out- side air temperature indicator marked ICY will blink.

WIC0187

Instruments and controls 2-5

Z X

CAUTION

If the gauge indicates engine coolant temperature over the normal range, stop the vehicle as soon as safely pos- sible. If the engine is overheated, con- tinued operation of the vehicle may seriously damage the engine. See the ‘‘In case of emergency’’ section for immediate action required.

WIC0188

LIC0165

TACHOMETER The tachometer indicates engine speed in revolutions per minute (r/min).

CAUTION

When engine speed approaches the red zone, shift to a higher gear. Oper- ating the engine in the red zone may cause serious engine damage.

ENGINE COOLANT TEMPERA- TURE GAUGE The gauge indicates the engine coolant temperature. The engine coolant temperature varies with the outside air temperature and driving con- ditions.

2-6 Instruments and controls

Z X

indicates that the fuel filler lid is The located on the driver’s side of the vehicle.

CAUTION

malfunction indicator

c If the vehicle runs out of fuel, the lamp (MIL) may come on. Refuel as soon as possible. After a few driving trips, the lamp should turn off. If the lamp remains on after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.

c For additional information, see the ‘‘Malfunction indicator lamp (MIL)’’ later in this section.

LIC0166

FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during brak- ing, turning, acceleration, or going up or down hills. The gauge needle returns to empty (E) after the ignition key is turned to OFF. The warning indicator light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge registers E (Empty).

Instruments and controls 2-7

Z X

WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS

or

Brake warning light

Low washer fluid warning light

Supplemental air bag warning light

Turn signal/hazard indicator lights

or

Anti-lock brake warning light

Low fuel warning light

High beam indicator light

Malfunction indicator lamp (emission system)

Trunk open warning light

Charge warning light

Engine oil pressure warning light

Traction control off indicator light

Door open warning light

CRUISE main switch indicator light (if so equipped)

Slip indicator light

Seat belt warning light and chime

Cruise SET switch indicator light (if so equipped)

CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights come on:

If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly. WARNING LIGHTS

or

The following lights come on briefly and then go off:

or

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop

2-8 Instruments and controls

the engine immediately and call an autho- rized NISSAN dealer. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See ‘‘Engine oil’’ in the ‘‘Maintenance and do-it-yourself’’ section.

Z X

CAUTION

Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so.

Charge warning light

If this light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the generator belt. is loose, broken, missing, or if the light remains on, see an authorized NISSAN dealer immedi- ately.

the belt

If

CAUTION

Do not continue driving if the belt is loose, broken or missing.

Door open warning light

This light comes on when any of the doors are not closed securely while the ignition key is ON.

Trunk open warning light

This light comes on when the trunk lid is not securely closed while the ignition key is ON. Seat belt warning light and chime

The light and chime remind you to fasten your seat belts. The light illuminates when- ever the ignition key is turned to ON, and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for about seven seconds unless the driver’s seat belt is securely fastened. in the ‘‘Seats, re- Refer to ‘‘Seat belts’’ straints and supplemental air bag systems’’ section for precautions on seat belt usage.

Supplemental air bag warning light

When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, supplemental side air bag (if so equipped) and pre-tensioner seat

belt systems need servicing and your vehicle must be taken to an authorized NISSAN dealer: c The supplemental air bag warning light re-

mains on after approximately 7 seconds.

c The supplemental air bag warning light

flashes intermittently.

c The supplemental air bag warning light

does not come on at all.

Unless checked and repaired, the supple- mental restraint system (air bag system) and/or the pre-tensioner seat belts may not function properly. For additional details, see ‘‘Supplemental in the ‘‘Seats, restraints and supplemental air bag systems’’ section.

restraint system’’

WARNING

is on,

it could mean that

If the supplemental air bag warning light the supplemental air bag or supplemental side air bag system (if so equipped) or pre-tensioner seat belt system will not operate in an accident.

Instruments and controls 2-9

Z X

Low washer light

fluid warning

This light comes on when the washer fluid is at a low level. Add washer fluid as neces- sary. See the ‘‘Maintenance and Do-it- yourself’’ section.

or

Brake warning light

functions for both the parking

This light brake and the foot brake systems. When the ignition key is in the ON position, the light comes on when the parking brake is applied, and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See ‘‘Brake and clutch fluid’’ in the ‘‘Maintenance and do-it- yourself’’ section of this Owner’s Manual. 2. If the brake fluid level is correct, have the brake system checked by an authorized NISSAN dealer.

2-10 Instruments and controls

WARNING

c Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be danger- ous.

c Pressing the brake pedal with the engine stopped and/or a low brake fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel.

c If the brake fluid level is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.

or

Anti-lock brake warning light (if so equipped)

If the light comes on while the engine is running, it may indicate the anti-lock portion of the brake system is not functioning prop-

erly. Have the system checked by an autho- rized NISSAN dealer. Turn off the engine, and start it again by slowly turning the ignition key (quickly doing so may cause the ABS light to stay on when there is nothing wrong). If the light stays on, have the system checked by an authorized NISSAN dealer. If an abnormality occurs in the system, the anti-lock function ceases, but the regular braking system continues to operate. If the light comes on while you are driving, contact an authorized NISSAN dealer for repair.

Low fuel warning light

This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).

Z X

INDICATOR LIGHTS

Turn signal/hazard indicator lights

The appropriate light flashes when the turn signal switch is activated. Both lights flash when the hazard switch is turned on.

High beam indicator (Blue)

light

This light comes on when the headlight high beam is on and goes out when the low beam is selected. The high beam indicator light also comes on when the passing signal is activated.

Cruise main switch indicator light (if so equipped)

The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. While the cruise main switch indicator light comes on, the cruise control system is operational.

Cruise set switch indicator light (if so equipped)

The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by your NISSAN dealer.

Malfunction indicator lamp (MIL)

If this indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control mal- function. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel filler cap is installed and closed tightly, and that the vehicle has at least three gallons of fuel in the fuel tank. lamp After a few driving trips, should turn off if no other potential emission control system malfunction exists.

the

Operation The malfunction indicator lamp will come on in one of two ways: c Malfunction indicator lamp on steady - An emission control system malfunction has been detected. Check the fuel filler cap. If the fuel filler cap is loose or missing, tighten or install the cap and continue to lamp should drive the vehicle. The turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

c Malfunction indicator lamp blinking - An engine misfire has been detected which may damage the emission control sys- tem. To reduce or avoid emission control system damage: a) do not drive at speeds above 45 MPH

(72 km/h).

tion.

b) avoid hard acceleration or decelera-

c) avoid steep uphill grades. d) if possible,

reduce the amount of

cargo being hauled or towed.

Instruments and controls 2-11

Z X

The malfunction indicator lamp may stop blinking and come on steady. Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your ve- hicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Traction control off indicator light

After turning the ignition key to the ON position, the light will illuminate. The light will turn off after about 2 seconds if the traction control system (TCS) is operational. If the light stays on or comes on when you are driving, it may indicate the traction con- trol system is not functioning properly. Have the system checked by your NISSAN dealer.

2-12 Instruments and controls

The light comes on when the traction control off switch is pushed to OFF. This indicates the traction control system is not operating. Push the traction control off switch again or restart the engine and the system will oper- ate normally. See “Traction control” in the “5. Starting and driving” section.

Slip indicator light

This indicator will blink when the traction control system is limiting wheelspin. Slip- pery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly. The slip indicator light also comes on when you turn the ignition key to ON. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or go off, have the traction control system checked by your NISSAN dealer. The sys- tem operates in all transmission shift lever positions. But the system can upshift the transmission only as high as the indicated shift lever position.

AUDIBLE REMINDERS Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as pos- sible if the warning sound is heard. Key reminder chime A chime sounds if is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch in the OFF position, a chime sounds when the driver’s door is opened with the headlight switch on. Turn the headlight switch OFF when leaving the vehicle.

the driver’s door

Z X

SECURITY SYSTEMS

IC0005

Your vehicle has two types of security sys- tems: c Nissan Vehicle Immobilizer System-

NVIS

c Vehicle security system (if so equipped)

NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The Nissan Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of a registered NVIS key. If the engine fails to start using a registered NVIS key (for example, when interference is caused by another NVIS key, an automated toll road device or automated payment device on the key ring), restart the engine using the following procedures: 1. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 5
seconds.

3. Repeat steps 1 and 2. 4. Restart the engine while holding the de- vice (which may have caused the inter- ference) separate from the registered NVIS key.

If the no start condition re-occurs, Nissan recommends placing the registered NVIS key on a separate key ring to avoid interfer- ence from other devices.

Statement related to section 15 of FCC rules for Nissan Vehicle Immobilizer System (CONT ASSY - IMMOBILIZER, ANT ASSY - IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the fol- lowing two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undes- ired operation of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE MANU- FACTURER FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OP- ERATE THE EQUIPMENT.

Instruments and controls 2-13

Z X

sible. Please bring all NVIS keys that you have when visiting your NISSAN dealer for service. VEHICLE SECURITY SYSTEM (if so equipped) The vehicle security system provides visual and audio alarm signals if parts of the vehicle are disturbed.

LIC0167

Security indicator light (Nissan Ve- hicle Immobilizer System) The security indicator light blinks every 3
seconds whenever the ignition switch is in the LOCK, OFF or ACC position. This func- tion indicates the Nissan Vehicle Immobi- lizer System (NVIS) is operational. If the NVIS is malfunctioning, the light will remain on while the ignition key is in the ON position. If the light still remains on and/or the engine will not start, see your Nissan dealer for NVIS service as soon as pos- 2-14 Instruments and controls

LIC0167

Security indicator light (Vehicle se- curity system) The security indicator light shows the status of the vehicle security system. The light operates whenever the ignition switch is in the LOCK, OFF, or ACC posi- tion. The vehicle security system has four phases. For each phase the operation of the security indicator light is different.

Z X

How to arm the vehicle security system 1. Close all windows. (The system can be armed even if the windows are open). 2. Remove the key from the ignition switch. 3. Close the hood, trunk lid and all doors. Lock all doors. The doors can be locked with the key, power door lock switch or with the keyfob. Keyfob operation: c Push the

button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.

c When the

button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked. The horn may or may not beep once. Refer to ‘‘Silencing the horn beep fea- ture’’ later in this section for details.

4. Confirm that the SECURITY indicator light comes on. The SECURITY light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30

seconds the vehicle security system auto- matically shifts into the armed phase. The SECURITY light begins to flash once ev- ery three seconds. If, during the 30- second pre-arm time period, the door is unlocked by the key or the keyfob, or the ignition key is turned to ACC or ON, the system will not arm.

c If the key is turned slowly when lock- ing the door, the system may not arm. Furthermore, if the key is turned ex- cessively to the unlock position, the system may be disarmed when the key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.

c Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors, hood and trunk lid closed and locked with the ignition key in the OFF position.

Vehicle security system activation The vehicle security system will give the following alarm: c The headlights blink and the horn sounds

intermittently.

Instruments and controls 2-15

LIC0053

Z X

c The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tam- pered with again. The alarm can be shut off by unlocking a door or trunk lid with the key, or by pressing the button on the keyfob.

The alarm is activated by: c opening the door or trunk lid without using the key or keyfob (even if the door is unlocked by releasing the door inside lock switch) or opening the trunk lid by operating the opener lever.

c opening the hood. How to stop an activated alarm The alarm stops only by unlocking a door or the trunk lid with the key, or by pressing the

button on the keyfob.

2-16 Instruments and controls

The hazard lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered. If the system does not operate as de- scribed above, have it checked by an authorized NISSAN dealer.

LIC0168

Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the keyfob. The instruc- tions are on the back of the keyfob. To deactivate: Press and hold the

and

buttons for at least two seconds.

The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the

and buttons for at least two seconds once

more.

Z X

WINDSHIELD WIPER AND WASHER SWITCH

REAR WINDOW DEFOGGER SWITCH

HI: Continuous high speed operation The wipers automatically cycle twice when the washer is activated.

CAUTION

c Do not operate the washer continu-

ously for more than 30 seconds.

c Do not operate the washer if the

reservoir tank is empty.

WIC0183

WARNING

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the wind- shield with the defroster before you wash the windshield.

SWITCH OPERATION Push the lever down to operate the wind- shield wipers. Pull the lever toward you to operate the washer. The intermittent operation speed is as fol- lows: c When the vehicle speed is continuously low, so is the intermittent operation speed.

c When the vehicle speed is continuously high, so is the intermittent operation speed.

LO: Continuous low speed operation

LIC0170

To defog the rear window glass, start the engine and push the rear window defogger switch on. The rear window defogger indi- cator light on the switch comes on. Push the switch again to turn the defogger off. The rear window defogger switch automati- cally turns off after approximately 15 minutes.

CAUTION

When cleaning the inner side of the window, be careful not to scratch or damage the rear window defogger.

Instruments and controls 2-17

Z X

HEADLIGHT AND TURN SIGNAL SWITCH

NOTE: The top few rows of wires on the rear window are not part of the rear window defogging system. These wires make up the antenna for the audio system.

XENON HEADLIGHTS WARNING HIGH VOLTAGE

c When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at an authorized NISSAN dealer.

c Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to an authorized NISSAN dealer and have the headlights adjusted correctly.

When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize. c The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn off the headlights for short inter- vals, (for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon headlights is not reduced.

c If the xenon headlight bulb is close to burning out, the brightness will dras- tically decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above NISSAN dealer.

appear,

contact

signs

2-18 Instruments and controls

Z X

HEADLIGHT SWITCH Lighting Turn the switch to the position: The parking, rear combination, side marker, li- cense plate and instrument panel lights come on. Turn the switch to the The headlights come on and all the other lights remain on. To select the high beam function, push the lever forward. The high beam lights come on and the indicator light illuminates. Pull it back to select the low beam.

position:

WIC0184

Instruments and controls 2-19

Z X

Passing signal Pulling and releasing the lever flashes the headlight high beams on and off. Daytime running light system (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The day- time running lights operate with the head- light switch in the OFF position or in the position. Turn the headlight switch to illumination when

the driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is re- leased. The daytime running lights will re- main on until the ignition switch is turned off.

position for full

WARNING

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring your- self and others.

WIC0185

Instrument brightness control The instrument cluster illuminates when the ignition switch is in ON position. The instrument brightness control operates when the light switch is in the AUTO,

or

position.

Turn the control to adjust the brightness of instrument panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off.

2-20 Instruments and controls

LIC0135

AUTOLAMP SYSTEM (if so equipped) The autolamp system allows the headlights to be set so they turn on and off automati- cally. The autolamp system can turn on the headlights automatically when it is dark, turn off the headlights when it is light, and keep the headlights on for up to 45 seconds after you turn the key to OFF and all doors are closed. If the ignition switch is turned OFF and one of the doors is opened, the headlights re- main ON for five minutes.

Z X

To set the autolamp system: 1. Make sure the headlight switch is in the

AUTO position.

2. Turn the ignition key to ON. 3. The autolamp system automatically turns

the headlights on and off.

, or

position.

To turn the autolamp system off, turn the switch to the OFF, Be sure you do not put anything on top of the autolamp sensor located in the top driver side of the instrument panel. The autolamp sensor controls the autolamp; if it is covered, the autolamp sensor reacts as if it is dark out and the head- lights will illuminate. If this occurs while parked with the engine off and the key in the ON position, your vehicle’s battery could become discharged.

TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automati- cally. Lane change signal To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.

FOG LIGHT SWITCH (if so equipped)

LIC0173

position:

Normal operation of the fog lights in the ON Headlight switch in the AUTO position; daytime operation c Fog lights, marker and taillights come

ON.

c Headlights do not come ON. c Dash readouts dim unless the dimmer

switch is on full bright.

c If the ignition switch is in the OFF position with the fog lights turned ON, a warning chime will sound indicating the fog lights Instruments and controls 2-21

Z X

To turn the fog lights OFF, turn the switch to the OFF position. The fog lights automatically turn off when- ever the high-beam headlight function is selected.

were left ON. The fog lights will be turned OFF by the Battery Saver function ap- proximately 5 minutes after the last door is closed.

c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Battery Saver function, the fog lights will immediately come back ON.

Headlight switch in the AUTO position; nighttime operation c Fog lights, marker and taillights come

ON.

c Headlights come ON. c Dash readouts dim unless the dimmer

switch is on full bright.

c If the ignition switch is in the OFF position with the fog lights turned ON, the fog lights will be turned OFF by the Twilight Sentinel function approximately 45 sec- onds after the last door is closed. When any door is opened when the ignition switch is in the OFF position, the Twilight Sentinel function operates for approxi- mately 5 minutes. After approximately 5

2-22 Instruments and controls

minutes, the lights will turn OFF due to the Battery Saver function.

c If the ignition switch is turned to the ON position after the fog lights were turned OFF by the Twilight Sentinel function, the fog lights and the headlights will come ON together when the Auto Light Sensor determines it is dark enough. The fog lights will now operate independently of the headlights only if the headlight switch is turned OFF.

c When the high-beams are turned ON, the fog lights will turn OFF. The fog lights will come back ON when the high-beams are turned OFF.

Headlights turned ON and OFF by the driver (no AUTO headlight function); day or nighttime operation c Same operation as ‘‘Headlight switch in the AUTO position; daytime operation’’ described above.

Some of the Battery Saver and Twilight Sentinel functions can be turned ON and OFF or adjusted. Please see your NISSAN dealer if you have any ques- tions.

Z X

HAZARD WARNING FLASHER SWITCH

HORN

c Do not use the switch while moving on the highway unless unusual cir- cumstances force you to drive so slowly that your vehicle might be- come a hazard to other traffic.

c Turn signals do not work when the hazard warning flasher lights are on.

The flashers can be actuated with the igni- tion switch either OFF or ON. Some state laws may prohibit the use of the hazard warning flasher switch while driving.

LIC0174

Push the switch on to warn other drivers when you must stop or park under emer- gency conditions. All turn signal lights flash.

WARNING

c If stopping for an emergency, be sure to move the vehicle well off the road.

WIC0119

To sound the horn, push the center pad area of the steering wheel.

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.

Instruments and controls 2-23

Z X

HEATED SEATS (if so equipped)

LIC0136

The front seats (if so equipped) are warmed by built-in heaters. The switches are located on the center console. 1. Start the engine. 2. Push the low or high position of

the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.

2-24 Instruments and controls

3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off.

CAUTION

c Do not use the seat heater for ex- tended periods or when no one is using the seat.

c Do not put anything on the seat which insulates heat, such as a blan- ket, cushion, seat cover, etc. Other- wise, the seat may become over- heated.

c Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

c Any liquid spilled on the heated seat should be removed immediately with a dry cloth.

c When cleaning the seat, never use benzine, thinner, or any similar ma- terials.

c If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.

c The battery could run down if the heater is operated while the engine is not running.

Z X

TRACTION CONTROL SYSTEM (TCS) CANCEL SWITCH (if so equipped)

POWER OUTLET

LIC0134

LIC0142

WIC0186

To cancel the Traction Control System (TCS), push the “TCS OFF” switch to turn off the system. The indicator will come on. Push the “TCS OFF” switch again or restart the engine and the system will operate normally. See “Traction control system” in the “Starting and driving” section.

The power outlet is for powering electrical accessories such as cellular telephones.

CAUTION

c Take care as the outlet and plug may be hot during or immediately after use.

c This power outlet is not designed for

use with a cigarette lighter unit.

c Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

Instruments and controls 2-25

Z X

c Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged bat- tery.)

c Avoid using when the air conditioner, headlights or rear window defogger is on.

c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned off.

c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tempera- ture fuse may blow.

c When not in use, be sure to close the cap. Do not allow water to contact the socket.

2-26 Instruments and controls

STORAGE

LIC0016

LIC0137

SEATBACK POCKETS (if so equipped) The seatback pockets are located on the back of the driver and passenger seats. The pockets can be used to store maps. SEATBACK SIDE POCKETS (if so equipped) A seatback side pocket is located on the inboard side of the front passenger seat.

SUNGLASSES CASE The sunglasses case can be opened by pushing the button.

WARNING

The sunglasses case should not be used while driving so full attention may be given to vehicle operation.

Z X

CAUTION

c Do not use for anything other than

sunglasses.

c Do not leave sunglasses in the sun- glasses case while parking in direct sunlight. The heat may damage the sunglasses.

WIC0138

LIC0175

CUP HOLDERS To open the front cup holders, lift the con- sole cover. To close, lower the console cover. The rubber cleaning. The rear cupholders are located in the fold- down armrest in the rear seat back.

insert may be removed for

WARNING

The cup holder should not be used while driving so full attention may be given to vehicle operation.

CAUTION

c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liq- uid is hot, it can scald you or your passenger.

Instruments and controls 2-27

Z X

c Use only soft cups in the cup holder. Hard objects can injure you in an accident.

CONSOLE BOX

WARNING

The center console box should not be used while driving so full attention may be given to vehicle operation.

CAUTION

c This power socket is not designed for use with a cigarette lighter unit. c Do not use accessories that exceed 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

LIC0176

GLOVE BOX The glove box opens by pulling the handle. When locking or unlocking the glove box, use the master key. The valet key cannot be used to lock or unlock the glove box.

WARNING

Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.

2-28 Instruments and controls

Z X

Upper half Pull up on the lever to open the upper half of the console box. The rubber mat may be removed for cleaning. The upper half of the console box may be used for storage of cellular phones. An access hole is provided at the bottom of the upper half of the console box for phone cord routing to the power socket. To route a phone cord to the power socket: 1. open the upper half of the console box 2. remove the rubber mat, and then remove

the cutout area from the mat

3. remove the access hole cover 4. install the rubber mat 5. route the phone cord through the access

hole and plug into the power socket

Lower half Pull up on the lever to open the lower half of the console box. A power socket is located inside the console box and there is storage for compact discs.

WIC0189

Armrest Push the button to elevate the armrest. To return armrest to regular position, push arm- rest rearward until locked.

LIC0181

COVERED STORAGE BOX Push the bottom center of the lid to open.

Instruments and controls 2-29

Z X

CARGO NET (if so equipped) The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion. To install the cargo net, attach the hooks to the retainers. To remove the cargo net, detach the hooks from the cargo net retainers.

2-30 Instruments and controls

WIC0190

Z X

WINDOWS

WARNING

POWER WINDOWS

c Properly secure all cargo to help pre-

vent it from sliding or shifting.

c Be sure to secure hooks into the retainers. The cargo restrained in the net must not exceed 30 lbs. (13.6 kg) or the net may not stay secured.

WARNING

c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before clos- ing the windows. Use the window lock switch to prevent unexpected use of the power windows.

c Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols and become trapped in a window. Unattended children could become involved in serious acci- dents.

LIC0177

If

The power windows operate when the igni- tion key is in the ON position, or for about 45
seconds after the ignition key is turned to the OFF position. the driver’s or front passenger’s door is opened during this pe- riod of about 45 seconds, power to the windows is cancelled. To open a window, press down on the switch. To close a win- dow, pull up on the switch. To stop the opening or closing function at any time, simply release the switch. The driver side control panel is equipped with switches to open or close all of the windows.

Instruments and controls 2-31

Z X

LIC0178

LIC0179

The front and rear passenger window switches operate only the corresponding passenger window. To open the window, press down on the switch. To close the window, pull up on the switch. Locking passenger windows When the power window lock switch on the driver side control panel is pushed in, only the driver side window can be opened or closed. Push it in again to cancel this func- tion.

2-32 Instruments and controls

Automatic operation To fully open the driver or passenger side window, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening. Auto-reverse function If the control unit detects something caught in the window as it is closing, the window will be immediately lowered. The auto-reverse function can be activated

when the window is closed by automatic operation when the ignition key is in the ON position or for 45 seconds after the ignition key is turned to the OFF position. Depending on the environment or driv- ing conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs.

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.

Z X

SUNROOF (if so equipped)

LIC0145

The sunroof only operates with the ignition key in the ON position. NOTE: If the battery is discharged or is discon- nected, the sunroof may not operate cor- rectly, and must be reset. From any sunroof position (full open, par- tially open, closed, partially vented and vented), push and hold the button in the forward position until the sunroof vents in the full-up position. This resets the sunroof motor memory and now the sunroof will operate correctly.

Sliding the sunroof To open the sunroof, push the switch to- ward DOWN/OPEN. To close the sunroof, push the switch to- ward UP/CLOSE. Tilting the sunroof Close the sunroof by pushing the switch toward UP/CLOSE. Release the switch, then push the UP/CLOSE switch to tilt the sunroof up. To tilt the sunroof down, push the switch toward DOWN/OPEN. Sun shade Open and close the sun shade by sliding it forward or backward.

WARNING

c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.

c Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is clos- ing.

CAUTION

c Remove water drops, snow,

ice or sand from the sunroof before opening. c Do not place heavy objects on the

sunroof or surrounding area.

Instruments and controls 2-33

Z X

INTERIOR LIGHT

MAP LIGHTS

−remain on for a maximum of 30

seconds.

−driver’s door is opened. −remain on for a maximum of 30
seconds after driver’s door is closed. −ignition key is removed from key

cylinder

−remain on for a maximum of 30

seconds.

The lights will go off when the ignition key is in the ON position, or the driver’s door is closed and locked. The lights will also go off after 10 minutes while doors are open. c When the switch is in the ON position, the interior light illuminates, whether any door is open or closed.

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

IC1235M

The interior light operates regardless of ignition key position. The interior light has a three-position switch. c When the switch is in the OFF position, the interior light does not illuminate, re- gardless of door position.

c When the switch is in the center j position, the front and rear personal lights will illuminate under the following conditions:

−driver’s door is unlocked.

2-34 Instruments and controls

Z X

LIC0147

LIC0146

To turn on the map lights, press the switches. To turn them off, press the switches again.

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

TRUNK LIGHT

The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off.

HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped) The HomeLinkT Universal Transceiver pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: c Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.

c Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLinkT will retain all pro- gramming.

If

Once the HomeLinkT Universal Trans- ceiver is programmed, retain the original transmitter for future programming pro- cedures (i.e., new vehicle purchases). Upon sale of the pro- grammed HomeLinkT Universal Trans- ceiver buttons should be erased for se- curity additional information refer to ‘‘Programming the HomeLinkT Universal Transceiver’’ later in this section.

the vehicle,

purposes.

For

Instruments and controls 2-35