Download PDF Manual

1. Push the (air recirculation) button


to the off position.


2. Push the 3. Move the fan control dial to the desired


button in.


position.


Heater, air conditioner and audio systems 4-5


Z X


three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.


c The air conditioner system should be operated for about ten minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.


c If the engine coolant temperature gauge exceeds the H (hot) position, turn the air conditioner off. See ‘‘If your vehicle over- heats’’ in the ‘‘In case of emergency’’ section of this owner’s manual for addi- tional information.


AIR FLOW CHARTS The charts on the following pages show the switch and lever positions for MAXIMUM and QUICK heating, cooling, or defrosting.


4. Push on the air conditioner button. The


indicator light comes on.


5. Move the temperature control lever to the


desired position.


Dehumidified defogging This mode defogs the windows and dehu- midifies the air. 1. Push the button in. When the button is pushed, the air conditioner automatically turns on to de- humidify the air, which helps to defog the windshield. The air recirculation mode automatically turns off.


2. Move the fan control dial to the desired


position.


3. Move the temperature control lever to the


desired position.


Outside air is drawn into the passenger compartment to improve the defogging per- formance. Operating tips c Keep the windows and sun roof closed while the air conditioner is in operation. c After parking in the sun, drive for two or 4-6 Heater, air conditioner and audio systems


Z X


Heater, air conditioner and audio systems 4-7


AHA1026


Z X


4-8 Heater, air conditioner and audio systems


AHA1025


Z X


Servicing air conditioner The air conditioner system in your NISSAN vehicle is charged with a refrigerant de- signed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See ‘‘Air conditioner system refrigerant and lubricant recommen- dations’’ in the ‘‘Technical and consumer information’’ section of this manual. Your NISSAN dealer is able to service your environmentally conscious air conditioner system.


WARNING


The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done only by an experienced technician with proper equipment.


Heater, air conditioner and audio systems 4-9


Z X


influences.


AM-FM RADIO WITH CASSETTE PLAYER RADIO OPERATION To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. ONzOFF/VOL control knob Turn the ignition key to ACC or ON, then push the ONzOFF/VOL control knob. The mode (radio or cassette) which was playing immediately before the system was turned off resumes playing. When no cassette is loaded, the radio comes on. Pushing the ONzOFF/VOL button again turns the system off. Turn the ONzOFF/VOL control knob to ad- just the volume.


Z X


4-10 Heater, air conditioner and audio systems


AHA1004


buttons together sets minutes.


Clock operation Pressing the CLOCK button alternates the clock and the radio/cassette tape options in the display. Clock set Depressing the CLOCK and the buttons together sets hours. Depressing the CLOCK and Clock priority mode In this mode the clock is shown in the display. If any radio or cassette tape func- tions are activated, the radio (or cassette tape) display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. Radio/Cassette tape priority mode In this mode, the radio station illuminates in the display during radio operation. During cassette tape operation, TAPE illuminates in the display.


button to change from AM


Selecting the desired band Push the to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal is weak, the radio au- tomatically changes from stereo to monaural reception. TUNE buttons


WARNING


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


tuning button


radio continues in the SEEK mode at the lowest broadcast station. SCAN tuning Push the for more than 1.5 seconds. SCAN illuminates in the display window. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Push- ing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.


and


Use the buttons for manual tuning. To move quickly through the chan- nels, hold either of the tune buttons down for more than 1.5 seconds. SEEK tuning Push the for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station. Pushing the button again continues the SEEK function. Once the highest broadcasting station is reached, the


tuning button


Heater, air conditioner and audio systems 4-11


Z X


The selected band illuminates in the dis- play.


2. Tune to the desired station. 3. Push the desired station select button for more than 2 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.


4. When the sound resumes, memorizing is


complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired sta- tions.


AHA1005


Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push 4-12 Heater, air conditioner and audio systems


to select AM, FM1, or FM2.


AHA1027


Adjusting tone quality and speaker balance To adjust BASSzTREBzFADERzBAL (Bass, Treble, Fader, Balance), press the AUDIO button until the desired mode (BAS, TRE, FAD or BAL) appears in the display. button to adjust Bass Press the (BAS) and Treble (TRE) to the desired level. Use the button to adjust Fader or Balalnce modes. Fader adjusts the sound level between the front and rear speakers and Balance (BAL) adjusts the


or


or


Z X


sound level between the right and left speakers. After 10 seconds, the radio or cassette tape display reappears. Once the sound quality is set to the desired level, press the AUDIO button repeatedly until the radio or cassette tape display appears. CASSETTE TAPE OPERATION Turn the ignition key to ACC or ON, and carefully insert a cassette tape into the tape door. The cassette tape automatically pulls into the player. The word TAPE and moving digital squares illuminate on the right side of the display window. If the radio is already operating, it automati- cally turns off and the cassette tape begins to play.


CAUTION


Do not force the cassette tape into the tape door. This could cause player damage.


The cassette tape automatically changes directions to play the other side when the first side is complete. At this time, the mov-


ing digital squares illuminate on the left side of the display window. Precautions on cassette player op- eration c To maintain good quality sound, NIS- SAN recommends using cassette tapes of 60 minutes or shorter in length.


c Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources.


c Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.


c Do not use cassettes with labels which are peeling and loose. If used, the label could jam in the player.


c If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jamming and wavering sound quality.


c Over a period of time, the playback head, capstan and pinch roller may collect a tape coating residue as the tape is played. This residue accumu- lation can cause weak or wavering sound, and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be dis- assembled for cleaning.


or


button for


forwarding or rewinding the


Fast tape Push either the the desired direction. The FF or REW symbol illuminates in the display. To stop the FF or REW function, press the button. Automatic Program Search (APS) fast forwarding or APS rewinding the tape Push either the button while the cassette tape is playing. The tape runs quickly, stops, then plays the next


again, or the


or


or


Heater, air conditioner and audio systems 4-13


Z X


and TAPE illuminate in the display window for about 10 seconds. The clock mode then returns to the display window. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation. Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the automatically comes out.


button. The cassette tape


selection from the beginning. Either the FF or REW symbol flashes in the display while searching for the selection. This system searches at the blank intervals between selections. If there is a blank inter- val within one selection or there is no inter- val between selections, the system may not stop in the desired or expected location. Changing the direction of tape play Push the (program) select button. The moving digital squares illuminate on either the right or left side of the display window to indicate the side of program play. Playing and stopping the cassette tape Push the button while the cassette tape is playing to stop the tape. Push the button again to play the tape. Dolby NR (noise reduction) Push the button for Dolby NR en- coded tapes to reduce high frequency tape noise. The illuminates in the display. If the display is in the clock priority mode when pressed, 4-14 Heater, air conditioner and audio systems


symbol


button


the


is


Z X


influences.


AM-FM RADIO WITH COMPACT DISC PLAYER RADIO OPERATION To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. ONzOFF/VOL control knob Turn the ignition key to ACC or ON, then push the ONzOFF/VOL control knob. The mode (radio or CD) which was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the ONzOFF/VOL button again turns the system off. Turn the ONzOFF/VOL control knob to ad- just the volume.


AHA1006


Heater, air conditioner and audio systems 4-15


Z X


Clock operation Pressing the clock button alternates the clock and the radio/CD player options in the display. Clock set Depressing the clock and buttons to- gether sets hours. Depressing the clock and


buttons together sets minutes.


Clock priority mode In this mode the clock is shown in the display. If any radio or CD functions are activated, the radio or CD display illumi- nates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode.


button to change from AM


FM/AM band select button Push the to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception. TUNE buttons


is weak,


WARNING


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


Use these buttons for manual tuning. To move quickly through the channels, hold either of the tuning buttons down for more than 1.5 seconds. SEEK/SCAN buttons SEEK tuning Push the SEEK/SCAN tuning button


or for less than 1.5 seconds. SEEK tuning begins from high to low frequencies or low to high frequencies, depending on which button is pressed, and stops at the next


If


using


station.


broadcasting station. Once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcasting the button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station. SCAN tuning Push the SEEK/SCAN tuning button


or for more than 1.5 seconds. SCAN ap- pears in the display window. SCAN tuning begins from high to low frequencies or low to high frequencies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for five seconds. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.


4-16 Heater, air conditioner and audio systems


Z X


1. Push


to select AM, FM1, or FM2. The selected band illuminates in the display.


2. Tune to the desired station. 3. Push the desired station select button for more than 3 seconds. For example, in the illustrations ch2 is to be memorized. The radio mutes when the select button is pushed.


4. The indicator, ch2, then illuminates in the display and the sound resumes. Memo- rizing is now complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations.


AHA1007


Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2).


Heater, air conditioner and audio systems 4-17


Z X


AHA1028


Adjusting tone quality and speaker balance To adjust BASS/TREB or FAD/BAL (Bass/Treble or Fader/Balance), press the AUDIO button until the desired mode (BAS, TRE, FAD, or BAL) appears in the display. button to adjust Bass Press the (BAS) and Treble (TRE) to the desired level. Use the button also to adjust (FAD) or Balance (BAL) modes. Fader Fader (FAD) adjusts the sound level be- tween the front and rear speakers and Bal- ance (BAL) adjusts the sound between the right and left speakers. 4-18 Heater, air conditioner and audio systems


or


or


COMPACT DISC (CD) PLAYER OPERATION Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automati- cally turns off and the compact disc begins to play.


CAUTION


Do not force the compact disc into the slot. This could damage the player.


PLAY/STOP button When this button is pushed with the compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play. When this button is pushed while the com- pact disc is playing, the compact disc stops playing. Fast forward or rewind button


or


When the button is pushed while the compact disc is playing, the com- pact disc plays at an increased speed while fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed. Program search buttons


When the button is pushed while the compact disc is playing, the selection fol- lowing the present one starts to play from


Z X


When a new compact disc is inserted, the play pattern automatically changes to ALL. CD EJECT button button is pushed with a com- When the pact disc loaded, the compact disc ejects. When the button is pushed while the compact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not removed within 10 seconds, it is pulled back into the slot. CD (DISC) indicator light This light comes on when a compact disc is loaded into the player.


CAUTION


c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.


c Do no expose the CD to direct sun-


light.


button several


button sev- the beginning. Push the eral times to skip several selections. Each time the button is pushed, the CD advances one selection. (When the last selection on the compact disc is skipped, the first selec- tion is played.) When the button is pushed, the selec- tion being played returns to the beginning. Push the times to skip back several selections. Each time the button is pushed, the CD moves back one selection. Repeat/Random button button is pushed while the When the compact disc is playing, the play pattern changes as follows. ALL: All selections are played repeatedly in sequence. 1: The current selection is repeated. RANDOM: Selections are played at ran- dom, not following the sequence on the compact disc. The same program may be repeated twice. Blank (no symbol): All selections are played in sequence, and the compact disc stops when the last selection is finished.


Heater, air conditioner and audio systems 4-19


Z X


influences.


AM-FM RADIO WITH CASSETTE PLAYER AND COMPACT DISC PLAYER RADIO OPERATION To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. This radio has an FM Diversity reception system, which employs two antennas. One is a rod type antenna; the other is an an- tenna printed on the rear window. This sys- tem automatically switches to the antenna which is receiving the strongest radio signal. ONzOFF/VOL control knob Turn the ignition key to ACC or ON, then push the ONzOFF/VOL control knob button. The mode (radio, tape or CD) which was playing immediately before the system was


Z X


4-20 Heater, air conditioner and audio systems


AHA1008


turned off resumes playing. When no CD or tape is loaded, the radio comes on. Pushing the ONzOFF/VOL control knob button again turns the system off. Turn the ONzOFF/VOL control knob to ad- just the volume. Clock operation Pressing the clock button alternates the clock and the radio/cassette/CD player op- tions in the display. Clock set Depressing the clock and buttons to- gether sets hours. Depressing the clock and


buttons together sets minutes.


Clock priority mode In this mode the clock is shown in the display. If any radio, cassette or CD func- tions are activated, the radio, cassette or CD display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priorty mode.


button to change from AM


FM-AM band select button Push the to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception. TUNE/DISC buttons


is weak,


WARNING


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


and


Use the buttons for manual tuning. To move quickly through the chan- nels, hold either of the tuning buttons down for more than 1.5 seconds. SEEK/SCAN buttons SEEK tuning Push the SEEK/SCAN tuning button


or for less than 1.5 seconds. SEEK tuning begins from high to low frequencies or low to high frequencies, depending on which but- ton is pressed, and stops at the next broad-


casting station. Once the highest broadcast- ing station is reached, the radio continues in the SEEK mode at the lowest broadcasting button, once the station. If using the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station. SCAN tuning Push the SEEK/SCAN tuning button


or for more than 1.5 seconds. SCAN tun- ing begins from low to high frequencies or high to low frequencies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for five seconds. During the SCAN function, SCAN comes on and the radio station blinks in the display window. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.


Heater, air conditioner and audio systems 4-21


Z X


The selected band illuminates in the dis- play.


2. Tune to the desired station. 3. Push the desired station select button for more than 3 seconds. For example, in the illustrations ch2 is to be memorized. The radio mutes when the select button is pushed.


4. The indicator, ch2, then illuminates in the display and the sound resumes. Memo- rizing is now complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations.


AHA1009


Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push 4-22 Heater, air conditioner and audio systems


to select AM, FM1, or FM2.


Z X


button is pushed with ei- When the ther the radio or compact disc turned on and a tape loaded, the compact disc or the radio turns off and the tape plays. While the tape is playing, pushing the button stops tape play. Pushing the


button again resumes tape play. FF (fast forward) and REW (rewind) buttons


or


button to fast forward the Push the tape. Push the button to rewind the tape. Either illuminates in the display. To stop the FF or REW function, press the Automatic Program Search (APS) FF and REW buttons


buttons.


, or


When the button is pushed while the tape is being played, the tape runs quickly, stops, then plays the next selection from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the tape fast forwards one additional selection. This number ap- pears in the display window. The tape can be fast forwarded through up to nine selec- Heater, air conditioner and audio systems 4-23


AHA1029


Adjusting tone quality and speaker balance To adjust BASS, TREB (treble), BAL (bal- ance) and FADER, the control knobs must be released from their stowed positions. Pushing the knobs once moves them from their stowed positions. In the released position, the knobs control tone quality. Turn the control knobs to adjust BASS and TREB (treble) to the desired level. From the released position, the knobs must then be pulled out in order to control FADER and BAL (balance) and FADER adjusts the


sound level between the front and rear speak- ers, and BAL (balance) adjusts the sound level between the right and left speakers. Once sound quality is set to the desired levels, return the control knobs to their stowed posi- tions by pushing them in completely. CASSETTE TAPE OPERATION PLAY/STOP TAPE button When the button is pushed with the system turned off and a tape loaded, the system comes on and the tape plays. The word TAPE illuminates in the display.


Z X


the


tions. (for example: 7 in the display indi- cates that button has been pushed seven times to skip forward through seven selections). When the button is pushed, the se- lection being played starts again from the beginning. Push the button several times to rewind several selections. Each time the button is pushed, the tape rewinds back one additional selection. The number of selections skipped appears in the display window as a negative number (for example: 27 in the display indicates that the button has been pushed seven times


illuminates in the or button is


to rewind back through seven selections). Either the or display when the pushed. The system searches for the blank intervals between selections. If there is a blank inter- val within one selection or there is no inter- val between selections, the system may not stop in the desired or expected location. PROG (Program) button Push the side while the tape is being played. The cassette tape automatically changes 4-24 Heater, air conditioner and audio systems


button to change the tape


directions to play the other side when the first side is complete. Dolby NR (noise reduction) Push the button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator illuminates in the display. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation. Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT button Push the tape. Precautions on cassette player op- eration c To maintain good quality sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length.


button to eject the cassette


c Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, moisture or magnetic sources.


c Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.


c Do not use cassettes that have peel- ing or loose labels. If used, the label could jam in the player.


c If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly. Loose tape may cause jamming and wavering sound quality.


c Over a period of time, the playback head, capstan and pinch roller may collect a tape coating residue as the tape is played. This residue accumu- lation can cause a weak or wavering sound and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be dis- assembled for cleaning.


Z X


COMPACT DISC (CD) PLAYER OPERATION Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio or cassette tape is already operating, it automatically turns off and the compact disc begins to play.


CAUTION


Do not force the compact disc into the slot. This could damage the player.


CD button When the button is pushed with the compact disc loaded and the tape or the radio playing, the tape or radio turns off and compact disc starts to play. Push the button again to stop compact disc play.


FF (fast forward) REW (rewind) buttons When the button is pushed while the compact disc is playing, the com-


or


pact disc plays at an increased speed while fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed. Automatic Program Search (APS) APS FF, APS REW buttons


When the button is pushed while the compact disc is playing, the selection fol- lowing the present one starts to play from the beginning. Push the button sev- eral times to skip several selections. Each time the button is pushed, the CD advances one additional selection. The number ap- pears in the display window. (When the last selection on the compact disc is skipped, the first selection is played.) button is pushed, the se- When the lection being played returns to the begin- ning. Push the button several times to skip back several selections. Each time the button is pushed, the CD moves back one selection.


PROG (program) button When the button is pushed while the compact disc is playing, the play pattern changes as follows. ALL: All selections are played repeatedly in sequence. 1. The current selection is repeated. RANDOM: Selections are played at ran- dom, not following the sequence on the compact disc. The same program may be repeated twice. Blank (no symbol): All selections are played in sequence, and the compact disc stops when the last selection is finished. When a new compact disc is inserted, the play pattern automatically changes to ALL. CD EJECT button When the button is pushed with a com- pact disc loaded, the compact disc ejects. When the button is pushed while the compact disc is playing, the compact disc ejects and the system turns off.


Heater, air conditioner and audio systems 4-25


Z X


ANTENNA


If the compact disc ejects and is not removed within 10 seconds, it is pulled back into the slot. CD (DISC) indicator light This light comes on when a compact disc is loaded into the player.


Power antenna (if so equipped) The power antenna automatically extends when the radio is turned on, and retracts when the radio is turned off. If the radio is left on, the antenna retracts and extends with the ignition key OFF-ON operation.


Manual antenna The manual antenna cannot be shortened, but can be removed. When you need to remove the antenna, turn its base counter- clockwise.


CAUTION


c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.


c Do not expose the CD to direct sun-


light.


CAUTION


c Before turning the radio on, make sure that there is no one near the antenna outlet and there is enough space for it to extend.


c To prevent damage, be sure that an- tenna is fully retracted before the vehicle enters an automated car wash.


c Dirt and other foreign matter on the power antenna rod may interrupt its operation. Clean the rod periodically with a damp cloth. This type of cleaning is especially important dur- ing the winter seasons in areas where road salt and other chemicals may be spread on road surfaces and splashed onto the antenna rod.


4-26 Heater, air conditioner and audio systems


Z X


CB RADIO OR CAR PHONE


Microphone installed model If equipped with a genuine cellular phone, your NISSAN features a non-directional microphone in the steering column cover, so it is not necessary to look at or speak directly into the microphone when calling. To do so could detract from the driving operation and cause an accident. See the manual for car phone operation. Pre-wired and antenna for phone installed model Some models are pre-wired to accept the genuine NISSAN cellular phone. In addition, the same model has the phone antenna built into the rear glass window. When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the MFI (Multiport Fuel Injection) system and other electronic parts.


CAUTION


c Keep the antenna as far as possible away from the Engine Control Mod- ule.


c Also keep the antenna wire more than 8 inches (20 cm) away from the MFI harness. Do not route the an- tenna wire next to any harness.


c Adjust the antenna standing-wave ratio as recommended by the manu- facturer.


c Connect the ground wire from the


CB radio chassis to the body.


c For details, consult an authorized


NISSAN dealer.


Heater, air conditioner and audio systems 4-27


Z X


MEMO


4-28 Heater, air conditioner and audio systems


Z X


5 Starting and driving


Precautions when starting and driving...................5-2
Exhaust gas (carbon monoxide) ............................5-2
Three way catalyst .................................................5-2
Avoiding collision and rollover................................5-3
Drinking alcohol/drugs and driving.........................5-3
Ignition switch.........................................................5-4
Manual transmission ..............................................5-4
Automatic transmission ..........................................5-4
Before starting the engine......................................5-5
Driving with automatic transmission (if so equipped) ...............................................................5-6
Overdrive switch.....................................................5-8


Driving with manual transmission ..........................5-9
Starting the engine...............................................5-10
Parking brake operation.......................................5-11
Cruise control .......................................................5-12
Break-in schedule ................................................5-14
Increasing fuel economy ......................................5-14
Parking/parking on hills........................................5-15
Power steering system.........................................5-16
Brake system........................................................5-16
Anti-lock brake system (ABS) (if so equipped) .............................................................5-17
Cold weather driving ............................................5-18


Z X


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


Do not leave children, unreliable adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.


EXHAUST GAS (Carbon Monoxide)


WARNING


Do not breathe exhaust gases; they contain colorless and odorless carbon monoxide. Carbon monoxide is dan- gerous. It can cause unconsciousness or death. c If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.


c Do not run the engine in closed


spaces such as a garage.


5-2 Starting and driving


c Do not park the vehicle with the engine running for any extended length of time.


c Keep the trunk lid closed while driv- ing, otherwise exhaust gases could be drawn into the passenger com- partment. If you must drive in this manner for some reason, take the following steps: 1. Open all the windows. 2. Set the air recirculation switch to off and the fan control at 4 (high) to circulate the air.


3. Be sure the rear seat armrest and


tray are closed.


c If electrical wiring or other cable connections must pass to a trailer through the seal on the trunk lid or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.


c The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service.


b. You suspect that exhaust fumes are entering into the passenger compartment.


c. You notice a change in the sound


of the exhaust system.


d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.


THREE WAY CATALYST The three way catalyst is an emission con- trol device installed in the exhaust system. Exhaust gases in the three way catalyst are burned at high temperatures to help reduce pollutants.


WARNING


c The exhaust gas and the exhaust system are very hot. Keep people or flammable materials away from the exhaust pipe.


c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


Z X


CAUTION


c Do not use leaded gasoline. Deposits from leaded gasoline seriously re- duce the three way catalyst’s ability to help reduce exhaust pollutants.


c Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the catalyst, caus- ing it to overheat. Do not keep driv- ing if if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle in- spected promptly by an authorized NISSAN dealer.


the engine misfires, or


c Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three way catalyst.


c Do not race the engine while warm-


ing it up.


c Do not push or tow your vehicle to


start the engine.


AVOIDING COLLISION AND ROLLOVER


DRINKING ALCOHOL/DRUGS AND DRIVING


WARNING


Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.


Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects, or cause the vehicle to roll over, particularly if the vehicle slides sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the- counter drugs which may cause drowsi- ness). Always wear your seat belt as out- lined in the ‘‘Seat belts’’ section of this manual, and also instruct your passengers to do so.


WARNING


Never drive under the influence of alco- hol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.


Nissan is committed to safe driving. How- ever, you must choose not to drive under the influence of alcohol. Every year thou- sands of people are injured or killed in alcohol related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that’s true for drugs, too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.


Starting and driving 5-3


Z X


position. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


IGNITION SWITCH


ASD1015


MANUAL TRANSMISSION The ignition switch includes an anti-theft steering lock device. The key can only be removed when the ignition switch is in the LOCK position. On manual transmission models, to turn the ignition key to LOCK from ACC or ON, turn the key to OFF, push the key in, then turn the key to LOCK. To lock the steering wheel, remove the key. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up 5-4 Starting and driving


ASD1014


AUTOMATIC TRANSMISSION On automatic transmission models the igni- tion lock is designed so the key cannot be turned to LOCK and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the key cannot be turned to the LOCK position, proceed as follows to remove the key.


Z X


1) Move the shift selector lever into the P


(Park) position.


2) Turn the ignition key slightly toward the


ON position.


3) Turn the key to the LOCK position. 4) Remove the key. If the key is removed from the ignition switch, the shift selector lever cannot be moved from P (Park). The shift selector lever can be moved if the ignition switch is in the ACC position. The shift selector lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ACC positions. The OFF position is indicated by a ‘‘1’’ on the key cylinder. When the ignition is in OFF, the steering wheel is not locked. To lock the steering wheel, remove the key. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove the key while driving. If the key is removed, the steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


Key positions LOCK Normal parking position (0) OFF (1) The engine can be turned off without locking the steering wheel. ACC (Accessories) (2) This position activates electrical accesso- ries such as the radio when the engine is not running. ON Normal operating position (3) This position turns on the ignition system and the electrical accessories. START (4) This position activates the starter motor, which starts the engine.


BEFORE STARTING THE ENGINE


c Make sure the area around the vehicle is


clear.


c Maintenance items listed here should be checked periodically, for example, each time you check engine oil.


c Check that all windows and lights are


clean.


c Visually inspect tires for their appearance and condition. Also check tires for proper inflation.


c Lock all doors. c Position seat and adjust head restraints. c Adjust inside and outside mirrors. c Fasten seat belts and ask all passengers


to do likewise.


c Check the operation of warning lights when key is turned to the ON (3) position. See ‘‘Checking bulbs’’ in the ‘‘Instru- ments and controls’’ section.


Starting and driving 5-5


Z X


positions if the ignition key is turned to LOCK or if the key is removed. If the battery charge is low, the shift selector lever can be moved if the igni- tion switch is in the ACC position.


DRIVING WITH AUTOMATIC TRANSMISSION (if so equipped)


WARNING


c Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), 2
or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose con- trol and have an accident.


c Cold engine idle speed is high, so use caution when shifting into a for- ward or reverse gear before the en- gine has warmed up.


c Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.


CAUTION


c When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.


c On slippery roads, do not downshift.


This may cause a loss of control.


5-6 Starting and driving


The automatic transmission in your vehicle is electronically controlled by the transmis- sion control module to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle c After starting the engine, fully depress the foot brake pedal before shifting the shift selector lever to the D (Drive), R (Reverse), 2 or 1 position. Be sure the vehicle is fully stopped before attempt- ing to shift the shift selector lever.


c Keep the foot brake pedal depressed


and shift into a driving gear.


c Release the foot brake, then gradually


start the vehicle in motion.


The automatic transmission is designed so the foot brake pedal MUST be de- pressed before shifting from P (Park) to any drive position while the ignition switch is ON. The shift lever cannot be moved out of P (Park) and into any of the other gear


Z X


Shifting with automatic transmission Push the button to shift into P (Park), R (Reverse) or from D (Drive) to 2. All other positions can be selected without pushing the button. P (Park): Use this position when the vehicle is parked or when starting the engine. Always be sure the vehicle is at a complete stop. For maxi- mum safety, depress the brake pedal, then push in the selector lever button and move the shift selector lever to the P (Park) posi- tion. Apply the parking brake. When parking


ASD0510


on a hill, apply the parking brake first, then move the shift selector lever into the P (Park) position. Shifting from P (Park) If the ignition switch is in the ON position and the foot brake pedal is depressed, but the shift selector lever still cannot be moved out of P (Park), follow these instructions. 1. Turn the ignition key to the lock position


and remove the key.


2. Apply the parking brake.


3. Reinsert the key and turn it to the ACC


position.


4. Depress the foot brake pedal, and move the gearshift selector lever to N (Neutral).


5. Start the engine. These instructions for starting the vehicle in N (Neutral) should only be used until service can be obtained by an authorized NISSAN dealer. R (Reverse): Use this position to back up. Always be sure the vehicle is at a complete stop before moving the shift selector lever to the R (Reverse) position. Check to ensure the area behind the vehicle is clear. With the brake pedal depressed, push in the selector lever button and move the shift selector lever to the R (Reverse) position. N (Neutral): Neither forward nor reverse gear is en- gaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving.


Starting and driving 5-7


Z X


forward


D (Drive): Use this position for all normal driving. 2 (Second gear): Use this position for hill climbing or engine braking on downhill grades. Do not shift into the 2 position at speeds above 74 MPH (119 Km/h). Do not exceed 74 MPH (119 Km/h) in the 2 position. 1 (Low gear): Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine brak- ing on steep downhill grades. Do not shift into the 1 position at speeds above 41 MPH (66 km/h). Do not exceed 41
MPH (66 km/h) in the 1 position. Accelerator downshift in D position For rapid passing or hill climbing while driv- ing, fully depress the accelerator pedal to the floor. This shifts the transmission down into second gear or first gear, depending on vehicle speed. 5-8 Starting and driving


ASD1004


OVERDRIVE SWITCH ON: With the engine running and the selector lever in the D (Drive) posi- tion, the transmission upshifts into OVERDRIVE as vehicle speed in- creases.


OVERDRIVE does not engage until the engine has reached operating tempera- ture.


OFF: For driving up and down long slopes where engine braking is necessary, push the OVERDRIVE switch once. The O/D OFF indicator light on the instrument panel comes on at this time. When cruising at a low speed or climbing a gentle slope, you may feel uncomfortable shift shocks as the transmission shifts between 3rd gear and overdrive repeatedly. In this case, depress the OVERDRIVE switch to turn the OVERDRIVE off. The O/D off indicator light on the instrument panel comes on at this time.


When driving conditions change, depress the overdrive switch on the selector/lever to turn the OVERDRIVE on. Remember not to drive at high speeds for extended periods of time with the OVER- DRIVE off. This reduces fuel economy.


Z X


DRIVING WITH MANUAL TRANSMISSION


WARNING


c Do not downshift abruptly on slip- pery roads. This may cause a loss of control.


c Do not over-rev the engine when shifting to a lower gear. This may cause a loss of control or engine damage.


CAUTION


c Do not rest your foot on the clutch pedal while driving. This may cause clutch damage.


c Stop your vehicle completely before


shifting into R (Reverse).


c When the vehicle is stopped for a duration, for example at a stop light, shift to N (Neutral) and release the clutch pedal with the foot brake ap- plied.


SD1022


Shifting with manual transmission To change gears, fully depress the clutch pedal, and then move the shift lever to the desired gear. After shifting, release the clutch pedal slowly. You cannot shift directly from 5th gear into R (Reverse). First shift into N (Neutral), then into R (Reverse). If it is difficult to move the shift lever into R (Reverse) or 1st, shift into N (Neutral), then release and depress the clutch pedal again and shift into R (Reverse) or 1st.


Suggested shift-up speeds Shown below are suggested vehicle speeds for shifting into a higher gear. These sug- gestions relate to fuel economy and vehicle performance. Actual shift-up speeds will vary according to road conditions, the weather and individual driving habits. For normal acceleration in low altitude ar- eas (less than 4,000 ft [1,219 m]):


GEAR CHANGE


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th


ACCEL shift point MPH (km/h) 15 (24) 25 (40) 36 (58) 40 (64)


CRUISE shift point MPH (km/h) 15 (24) 18 (29) 30 (48) 39 (63)


For quick acceleration in low altitude areas and high altitude areas (over 4,000 ft [1,219
m]): GEAR CHANGE 1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th


MPH (km/h) 15 (24) 25 (40) 40 (64) 45 (72)


Starting and driving 5-9


Z X


Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear sug- gested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will ensure safe operation. Do not over-rev the engine when shifting to a lower gear as it may cause engine damage or loss of vehicle control.


GEAR 1st 2nd 3rd 4th 5th


MPH (km/h) 30 (50) 60 (95) 90 (145) − −


5-10 Starting and driving


STARTING THE ENGINE


1. Apply the parking brake. 2. Automatic transmission:


Move the shift selector lever to P (Park) or N (Neutral). (P is recommended.) The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF or if the key is removed. The starter is designed not to operate if the shift selector lever is in any of the driving positions. Manual transmission: Move the shift selector lever to N (Neu- tral), and depress the clutch pedal to the floor while cranking the engine. The starter is designed not to operate unless the clutch pedal is fully de- pressed.


3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. — If the engine is very hard to start in extremely cold or hot weather, de- press and hold the accelerator pedal


to help start the engine. — In the summer, when restarting the engine within 30 minutes after it has been stopped, keep the accelerator pedal fully depressed while starting.


CAUTION


Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, other- wise the starter could be damaged.


4. Warm-up


Allow the engine to idle for at least 30
seconds after starting. Drive at moderate speed for a short distance first, especially in cold weather.


Z X


PARKING BRAKE OPERATION


WARNING


c Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident.


c Do not release the parking brake


from outside the vehicle.


c Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully en- gaged.


c Do not leave children unattended in a vehicle. They could release the park- ing brake and cause an accident.


ASD1001


To engage: pull the lever up. To release: 1. Firmly apply foot brake. 2. Manual transmission models:


Place the shift selector lever in the N (neutral) position. Automatic transmission models: Move the shift selector lever to the P (park) position.


3. While pulling up on the parking brake lever slightly, push the button and lower completely.


4. Before driving, be sure the brake warning


light goes out.


Starting and driving 5-11


Z X


CRUISE CONTROL


Precautions c If the cruise control system malfunctions, it cancels automatically. The cruise light in the instrument panel then blinks to warn the driver.


c If the cruise light in the instrument panel blinks, turn the cruise control main switch off and have the system checked by an authorized NISSAN dealer.


c The cruise indicator light in the instru- ment panel may blink when the cruise control main switch is turned ON while pushing the RES/ACCEL, COAST/SET,


5-12 Starting and driving


ASD1005


or CANCEL switch (located on the steer- ing wheel). To properly set the cruise control system, perform the preceding steps in the order indicated.


WARNING


Do not use the cruise control when driving under the following conditions: c it is not possible to keep the vehicle


at a set speed.


c in heavy traffic or in traffic that var-


ies in speed.


c on winding or hilly roads.


c on slippery roads (rain, snow, ice,


etc.).


c in very windy areas. Doing so could cause a loss of vehicle control and result in an accident.


CAUTION


On manual transmission models, do not shift into neutral without depress- ing the clutch pedal when the cruise control is on. Should this occur, de- press the clutch pedal and turn the main switch off immediately. Failure to do so may cause engine damage.


The cruise control allows driving at a speed between 30 to 90 MPH (48 to 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The indicator light on the switch comes on. To set cruising speed, accelerate the ve- hicle to the desired speed, push the COAST/SET switch and release it. The CRUISE light in the instrument cluster


Z X


comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. c To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previ- ously set speed.


c The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control. To cancel the preset speed, use one of the following three methods: a) Push the CANCEL button; the CRUISE light in the instrument cluster goes out. b) Tap the brake pedal; the CRUISE light


goes out.


c) Turn the main switch off. Both the ON indicator on the main switch and CRUISE light in the instrument cluster go out.


The cruise control is automatically can- celled and the CRUISE light in the instru- ment panel goes out if: c you depress the brake or clutch pedal while pushing the RES/ACCEL or COAST/SET switch.


c the vehicle slows down more than 8 MPH


(13 km/h) below the set speed.


c you depress the clutch pedal (manual transmission), or move the shift selector lever to N (Neutral) (automatic transmis- sion).


To reset at a faster cruising speed, use one of the following three methods. a) Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.


b) Push and hold the RES/ACCEL switch. When the vehicle attains the speed you desire, release the switch.


c) Push and release the RES/ACCEL switch. the set speed


Each time you do this, increases by about 1 MPH (1.6 km/h).


To reset at a slower cruising speed, use one of the following three methods: a) Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it.


b) Push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed.


c) Push and release the COAST/SET switch. Each time you do this, the set speed decreases by about 1 MPH (1.6
km/h).


To resume the preset speed, push and re- lease the RES/ACCEL switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 30 MPH (48 km/h).


Starting and driving 5-13


Z X


BREAK-IN SCHEDULE


INCREASING FUEL ECONOMY


During the first 1,000 miles (1,600 km), follow these recommendations for the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in vehicle damage or shortened engine life. c Do not drive over 55 MPH (90 km/h) and do not run the engine over 4,000 rpm. Avoid driving for long periods at constant speed, either fast or slow.


c Do not accelerate at full throttle in any


gear.


c Avoid quick starts. c Avoid hard braking as much as possible. c Do not tow a trailer for the first 500 miles


(800 km).


5-14 Starting and driving


SD1001M


c Accelerate slowly and smoothly. Main- tain cruising speeds with a constant ac- celerator position.


c Drive at moderate speeds on the high- way. Driving at high speed lowers fuel economy.


c Avoid unnecessary stopping and brak- ing. Maintain a safe distance behind other vehicles.


c Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.


c Avoid unnecessary engine idling.


c Keep your engine tuned up. c Follow the recommended periodic main-


tenance schedule.


c Keep the tires inflated at


the correct pressure. Low tire pressure increases tire wear and wastes fuel.


c Keep the front wheels in correct align- ment. Improper alignment increases tire wear and lowers fuel economy.


c Air conditioner operation lowers fuel economy. Use the air conditioner only when necessary.


c When cruising at highway speeds, it is more economical to use the air condi- tioner and leave the windows closed to reduce drag.


Z X


PARKING/PARKING ON HILLS


WARNING


Do not park the vehicle over flammable materials such as dry grass, waste pa- per or rags. They may ignite and cause a fire.


1. Firmly apply the parking brake. 2. Manual transmission models:


Place the shift lever in the R (Reverse) position. When parking on an uphill grade, place the shift lever in 1 (First) gear.


SD1006M


Automatic transmission models: Move the gearshift lever to the P (Park) position.


WARNING


Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) posi- tion (automatic) or in the appropriate gear (manual). Failure to do so could cause the vehicle to move unexpect- edly or roll away and result in an acci- dent. Make sure the shift lever has been


pushed as far forward as it can go and cannot be moved without depressing the button at the end of the lever.


3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated.


c HEADED DOWNHILL WITH CURB: s1
Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.


c HEADED UPHILL WITH CURB: s2


Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.


c HEADED UPHILL OR DOWNHILL, NO


CURB: s3
Turn the wheels toward the side of the road so the vehicle will move away from the center of the road if it moves.


4. Turn the ignition key to the LOCK posi-


tion and remove the key.


Starting and driving 5-15


Z X


POWER STEERING SYSTEM


BRAKE SYSTEM


WARNING


c Never leave the engine running while


the vehicle is unattended.


c Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.


The power assisted steering is designed to use a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the hydraulic pump drive belt breaks, you will still have control of the vehicle. However, much greater steer- ing effort is needed, especially in sharp turns and at low speeds.


WARNING


If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be much harder to operate.


5-16 Starting and driving


The brake system has two separate hydraulic circuits. If one circuit develops a problem, you will still have braking at two wheels. Vacuum assisted brake The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake

Loading...
x