Download PDF Manual

vehicle locks all doors. Turning the front door key one time to the rear of the vehicle unlocks the correspond- ing door. From that position, returning the key to Neutral (where the key can only be removed and inserted) and turning it to the rear again within 5 seconds unlocks all doors.


To lock from the outside without a key, push the door lock button (driver side only) or the door lock knob (driver or passenger side), then close the door. When locking the door this way, be certain not to leave the key inside the vehicle. All doors automatically unlock with the key in the ignition.


WARNING


c Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.


c Before opening any door, always look for and avoid oncoming traffic.


2-3


Z X


c Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.


PD1101


CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent rear doors from being opened accidentally, especially when small children are in the vehicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can be opened only from the outside.


2-4


MULTI-REMOTE CONTROL SYSTEM (if so equipped) It is possible to lock/unlock all doors, turn the interior light on and activate the panic alarm by using the remote controller from outside the vehicle. Be sure to remove the key from the vehicle before locking the doors and leaving it. The remote controller can operate at a distance of approximately 49 ft (15 m) from the vehicle. (The effective distance depends on the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact your NISSAN dealer.


CAUTION


Listed below are conditions or occur- rences which will damage the remote controller: c Do not allow the remote controller to


become wet.


Z X


c Do not drop the remote controller. c Do not strike the remote controller


sharply against another object.


c Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).


Locking doors 1. Remove the ignition key. 2. Close all of the doors. 3. Push the controller.


button on the multi-remote


4. All of the doors lock. 5. The hazard indicators flash twice. c When the


doors flashes twice as a reminder that doors are already locked.


button is pushed with all the hazard indicator the


locked,


Unlocking doors 1. Push the


button on the multi- remote controller. Only the driver side door unlocks.


2. Push the


button on the multi- 2-5


APD0641


remote controller again within five sec- onds. The passenger doors unlock.


3. The interior light comes on and stays on for 30 seconds when the light switch is in the O position.


Z X


BATTERY REPLACEMENT


The interior light can be turned off without waiting 30 seconds by inserting the key into the ignition or locking the doors with the multi-remote controller or pushing the interior light button to OFF. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the alarm to call attention as follows: 1. Push the


button on the remote con-


troller for longer than 1.5 seconds.


2. The theft warning alarm and headlights


will stay on for 30 seconds.


3. The panic alarm stops when: c it has run for 30 seconds, or c the c the


or the button is pressed, or button is pushed for longer than 1.5 seconds on the multi-remote control- ler.


Replace the battery in the multi-remote con- troller as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one.


Insert the battery as illustrated above.


2-6


APD0535


Recommended battery: Sanyo CR2025
or equivalent.


3. Close the lid securely. 4. Press the


button, then the


button two or three times to check the multi- remote controller operation.


Z X


ceived including interference that may cause undesired operation of the device.


If the batteries are removed for any rea- son other than replacement, perform step 4 above. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry.


c The operational range of the multi- remote controller extends to approxi- mately 49 ft (15 m) from the vehicle. This range may vary with conditions.


FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re-


2-7


Z X


HOOD RELEASE


GLOVE BOX


APD0505


PD1310


1. Pull


the hood lock release handle s1
located below the instrument panel; the hood springs up slightly.


2. Push the lever s2 at the front of the hood with your fingertips and raise the hood. 3. Insert the support rod s3 into the slot on


the underside of the hood.


4. When closing the hood, return the sup- port then slowly close the hood and make sure it locks into place.


rod to its original position,


WARNING


c Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.


c If you see steam or smoke coming to


from the engine compartment, avoid injury do not open the hood.


2-8


Use the master key to lock or unlock the glove box. The glove box opens by pulling the handle. To illuminate the interior of the glove box, the headlight switch must be turned to the


or


position (If so equipped).


CAUTION


Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.


Z X


TRUNK LID LOCK OPERATION


Opener lever operation The trunk lid opener lever is located on the outside of the driver’s seat. To open the trunk lid, pull up the opener lever. To close, lower and push the trunk lid down securely.


APD0506


PD1312


Key operation To open the trunk lid, turn the key clock- wise. To close, lower and push the trunk lid down securely.


WARNING


Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See ‘‘Exhaust Gas’’ in the ‘‘Starting and Driving’’ Section.


2-9


Z X


FUEL FILLER LID LOCK OPERATION


APD0111


OPENER CANCEL LEVER FOR TRUNK LID When this lever is in the cancel position, the trunk lid cannot be opened with the trunk lid opener lever. It can be opened only with the key.


Opener lever operation The fuel filler lid opener lever is located on the outside of the driver’s seat. To open the fuel filler lid, push the opener lever down. To lock, close the fuel filler lid securely.


APD0525


2-10


Z X


WARNING


c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seri- ously injured if it is misused or mis- handled. Always stop the engine and do not smoke or allow open flames or sparks vehicle when refueling.


near


the


PD1013


FUEL FILLER CAP The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until ratch- eting clicks are heard.


c Fuel may be under pressure. Turn the cap one-half turn, and wait for any ‘‘hissing’’ sound to stop to pre- vent fuel from spraying out and pos- sible personal injury. Then remove the cap.


c Use only a genuine NISSAN fuel filler cap as a replacement. It has a built-in safety valve needed for proper op- eration of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunc- tion and possible injury.


CAUTION


If fuel is spilled on the car body, flush it away with water to avoid paint damage.


2-11


Put the fuel filler cap on the cap holder while refueling.


PD1014


Z X


FRONT SEATS


SEAT ADJUSTMENT


WARNING


c Do not adjust the driver’s seat while driving. The seat may move sud- denly and could cause loss of con- trol of the vehicle.


c After adjustment, gently rock in the is securely


to make sure it


seat locked.


APD0532


Forward and backward Pull the lever up while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in posi- tion.


2-12


Z X


APD0531


Reclining To recline the seatback, pull the lever up and lean back. To bring the seatback for- ward again, pull the lever and move your- body forward. The seatback moves forward.


WARNING


Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.


APD0654


For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat properly. See ‘‘Pre- cautions on Seat Belt Usage’’ later in this chapter.


2-13


Z X


protection against injury in an accident. Do not remove them. Check the adjust- ment after someone else uses the seat.


APD0526


PD1319


Lumbar support (If so equipped) The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area.


HEAD RESTRAINTS Adjust the head restraints so the top is level with the tops of your ears. To raise the head restraint, simply pull it up. To lower, push the lock knob and push the head restraint down.


WARNING


Head restraints should be adjusted properly as they may provide significant


2-14


Z X


REAR SEAT


Center armrest and tray Pull the armrest forward until it is horizontal, then release the lever (inset) and pull the tray forward. With the armrest in this posi- tion, you are able to gain access to the trunk.


PD1320


2-15


Z X


SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG SYSTEM)


This Supplemental Restraint System sec- tion contains important information concern- ing the driver and passenger supplemental air bags. The Supplemental Restraint Sys- tem Air Bag can help reduce impact force to the driver and to the front passenger in certain frontal collisions. The supplemental air bags are designed to supplement the crash protection provided by the driver and front passenger seat belts and are not a substitute for them. The seat belts should always be correctly worn and the driver and front passenger seated a suitable distance away from the steering wheel and instru- ment panel. (See ‘‘Seat belts’’ for instruc- tions and precautions on seat belt usage.) The supplemental air bags operate only when the ignition switch is in the ON or START position.


WARNING


c The supplemental air bags ordinarily will not inflate in the event of a side impact, rear impact, roll over, or lower severity frontal collision. Al- ways wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.


APD0717


far away as practical from the steer- ing wheel or instrument panel. Al- ways use the seatbelts.


c Keep hands on the outside of the steering wheel. Placing them inside the steering wheel rim could in- crease the risk that they are injured when the supplemental air bag in- flates.


c The seat belts and the supplemental air bags are most effective when you are sitting back and upright in the seat. Supplemental air bags inflate If you are unre- with great force. strained, leaning forward, sitting sideways or out of position in any way, you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the supplemental air bag if you are up against it when it inflates. Always sit back against the seatback and as


2-16


Z X


APD0656


APD0650


2-17


APD0651


Z X


WARNING


c Never let children ride unrestrained. Do not attempt to hold them in your lap or arms. Some examples of dan- gerous riding positions are shown in the previous illustrations.


c Children may be severely injured or killed when the supplemental air bag inflates if they are not properly restrained.


c Also, never install a rear-facing child restraint in the front seat. An inflat- ing supplemental air bag could seri- ously injure or kill your child. See ‘‘Child restraints for infants and small children’’ for details.


APD0652


APD0660


APD0653


APD0648


2-18


Z X


SUPPLEMENTAL AIR BAG SYSTEM


the steering wheel;


The driver supplemental air bag is located in the center of the front passenger supplemental air bag is mounted in the dashboard above the glove box. The supplemental air bag system is designed to inflate in higher severity frontal collisions, al- though it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental air bag operation. When the supplemental air bag inflates, a fairly loud noise may be heard, followed by


APD0530


the release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to unintentionally inhale it, as it may cause irritation and choking. Those with a history of breathing trouble should get fresh air promptly. The supplemental air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the occupant. They can help save lives and reduce seri- ous injuries. However, an inflating supple- mental air bag may cause facial abrasions or other injuries. Supplemental air bags do not provide restraint to the lower body.


2-19


Seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dashboard. Since the supplemental air bag inflates quickly in order to help protect the occupant, the force of the supplemental air bag inflating can increase the risk of injury if the occupant is too close to or is against the supplemental air bag module during inflation. The supplemental air bag deflates quickly after a collision. The supplemental air bags operate only when the ignition switch is in the ON or START position.


WARNING


c Do not place any objects on the steer- ing wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steer- ing wheel or instrument panel. Such objects may become dangerous pro- jectiles and cause injury if the supple- mental air bag inflates.


c Right after inflation, several supple- mental air bag system components will be hot. Do not touch them; you may severely burn yourself.


Z X


should not be modified or discon- nected. Unauthorized electrical test equipment and probing devices should not be used on the supple- mental air bag system.


c The SRS wiring harnesses are cov- ered with yellow insulation either just before the harness connectors or over the complete harness for easy identification.


When selling your vehicle, we request that you inform the buyer about the supple- mental air bag system and guide the buyer to the appropriate sections in this Owner’s Manual.


c No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air bag system.


c Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the supplemental air bag system.


c Tampering with the supplemental air bag system may result in serious per- sonal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the dashboard, or by install- ing additional trim material around the supplemental air bag system.


c Work around and on the supplemen- tal air bag system should be done by an authorized NISSAN dealer. Instal- lation of electrical equipment should also be done by an authorized NIS- SAN dealer. The yellow SRS wiring


2-20


Z X


WARNING LABELS


SUPPLEMENTAL AIR BAG WARNING LIGHT


Warning labels about the supplemental air bag system are placed in the vehicle as shown in the illustration.


APD0513


APD0523


The supplemental air bag warning light, displaying AIR BAG in the instrument panel, monitors the circuits of the supplemental air bag. The circuits monitored by the supple- mental air bag light are the diagnosis sensor unit, supplemental air bag modules and all related wiring. When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.


2-21


Z X


c The supplemental air bag system should be inspected by an autho- rized NISSAN dealer if there is any damage to the front end portion of the vehicle.


an


c If you need to dispose of a supple- mental air bag or scrap the vehicle, contact authorized NISSAN dealer. Correct supplemental air bag disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal proce- dures could cause personal injury.


If any of the following conditions occur, the supplemental air bag needs servicing: 1. The supplemental air bag light does not come on and remain on for 7 seconds and then go off as described above.


2. The supplemental air bag light flashes


intermittently or remains on.


3. The supplemental air bag light does not


come on at all.


Under these conditions, the Supplemental Restraint System Air Bag may not operate properly. It must be checked and repaired. Take your vehicle to the nearest authorized NISSAN dealer.


WARNING


If the supplemental air bag warning light is on, it could mean that the air bag will not operate in an accident.


Repair and replacement procedure The supplemental air bag system is de- signed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag light remains illumi- nated after inflation has occurred. Repair


the supplemental air and replacement of bag system should be done only by an authorized NISSAN dealer. To ensure long-term functioning, the system must be inspected 10 years after the date of manufacture as noted on the certification label located on the driver side front pillar. When maintenance work is required on the vehicle, the supplemental air bag system and related parts should be pointed out to the person conducting the maintenance. The ignition key should always be in the LOCK position when working under the hood or inside the vehicle.


WARNING


c Once the supplemental air bag in- flates, the supplemental air bag module will not function again and should be replaced by an authorized NISSAN dealer. The supplemental air bag module cannot be repaired.


2-22


Z X


SEAT BELTS


PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly adjusted, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Some states and all Canadian provinces or territories require that seat belts be worn at all times when a vehicle is being driven.


APD0658


APD0718


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be prop- erly restrained and, if appropriate, in a child restraint.


c The belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an acci- dent. Serious injury or death can occur if the seat belt is not worn properly.


2-23


c Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder.


c Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of inter- nal injuries in an accident.


Z X


c If the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indi- cate a malfunction in the system. Have the system checked by your NISSAN dealer.


c All seat belt assemblies including retractors and attaching hardware should be inspected after any colli- sion at your NISSAN dealer. NISSAN recommends that all seat belt as- semblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use dur- ing a collision should also be in- spected and replaced if either dam- age or improper operation is noted.


APD0533


c Be sure the seat belt tongue is se- curely fastened to the proper buckle. c Do not wear the belt inside out or twisted. Doing so may reduce its effectiveness.


c Do not allow more than one person


to use the same belt.


c Never carry more people in the ve-


hicle than there are seat belts.


2-24


Z X


CHILD SAFETY Children need adults to help protect them.


WARNING


Infants and children need special pro- tection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints.


All U.S. states and provinces of Canada require the use of approved child restraints for infants and small children. (See ‘‘Child Restraints for Infants and Small Children’’ later in this section.) In addition, there are many types of child restraints available for larger children which should be used for maximum protection. Infant or small child NISSAN recommends that infants or small children be placed in child restraints that


that


comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint fits your vehicle and always follow the manufacturer’s instruc- tions for installation and use. Children Children who are too large for child re- straints should be seated and restrained by the seat belts which are provided. NISSAN recommends that children sit in the rear seat if possible. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially avail- able) may help overcome this. The booster seat should raise the child so that the shoul- der belt is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Mo- tor Vehicle Safety Standards. Once the


2-25


child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.


WARNING


Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is mov- ing. The child could be seriously in- jured or killed in an accident.


Pregnant women NISSAN recommends that pregnant women use seat belts. Contact your doctor for spe- cific recommendations. The lap belt should be worn snug and positioned as low as possible around the hips, not the waist. Injured persons NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations.


Z X


For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.


Fastening the belts 1. Adjust the seat.


APD0500


3-POINT TYPE WITH RETRACTOR


WARNING


c Every person who drives or rides in this vehicle should use a seat belt at all times.


c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries.


PD1023M


2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until it snaps.


The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the belt to move, and allows you some freedom of move- ment in the seat.


2-26


Z X


PD1024M


3. Position the lap belt portion low and


snug on the hips as shown.


4. Pull the shoulder belt portion toward the


retractor to take up extra slack.


The front passenger side seat belt and rear 3-point seat belts have a cinching mecha- nism for child seat installation. It is referred to as the automatic locking mode. When the cinching mechanism is activated the seat belt cannot be withdrawn further until the seat belt tongue is detached from the buckle and fully retracted. Once re- tracted, the seat belt is in the emergency


locking mode. Refer to ‘‘Child Restraints for Infants and Small Children’’ later in this section for more information. The automatic locking mode should be used only for child seat installation. Dur- ing normal seat belt use by a passenger, the locking mode should not be acti- vated. If it is activated it may cause uncomfortable seat belt tension. Unfastening the belts To unfasten the belt, press the button on the buckle. The seat belt automatically retracts.


Checking seat belt operation (3-point type with retractor) Seat belt retractors are designed to lock belt movement using two separate methods: 1) When the belt is pulled quickly from the


retractor.


2) When the vehicle slows down rapidly. To increase your confidence in the belts, check their operation as follows: c Grasp the shoulder belt and pull quickly forward. The retractor should lock and restrict further belt movement. the retractor does not


If lock during this check or if you have any questions about belt operation, see your NISSAN dealer.


2-27


Z X


WARNING


After adjustment, release the buttons and try to move the shoulder belt an- chor up and down to make sure it is securely fixed in position.


PD1321


Shoulder belt height adjustment (For front seats) The shoulder belt anchor height should be adjusted to the position best for you. (See ‘‘Precautions on Seat Belt Usage’’.) To ad- just, squeeze the release buttons and move the shoulder belt anchor to the desired position, so the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off of your shoulder.


APD0105


2-POINT TYPE WITHOUT RETRACTOR (center position of rear seat) Fastening the belts 1. Insert the tongue into the buckle until it snaps. Both the tongue and the buckle are marked CENTER.


2-28


Z X


ICM021


APD0106


APD0104


2. To lengthen, hold the tongue at a right angle to the belt and pull on the belt. To shorten, pull the end of the belt attached to the belt clip away from the tongue, then pull the belt clip to take up the slack.


3. Position the lap belt low and snug on


the hips as illustrated. Unfastening the belt To unfasten the belt, press the button on the buckle.


Selecting correct set of belts The center seat belt buckle and tongue are identified by the CENTER label. The center seat belt tongue can be fastened only into the center seat belt buckle.


2-29


Z X


is not possible to properly fit


SEAT BELT EXTENDERS If, because of body size or driving position, it the lap- shoulder belt and fasten it, an extender is available which is compatible with the in- stalled seat belts. The extender adds ap- proximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position. See your NIS- SAN dealer for assistance if the extender is required.


WARNING


c Only NISSAN belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN belts.


c Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.


SEAT BELT MAINTENANCE c To clean the seat belt webbings, apply a mild soap solution or any solution rec- ommended for cleaning upholstery or carpets. Then brush the webbing, wipe it with a cloth and allow it to dry in the shade. Do not allow the seat belts to retract until they are completely dry.


c If dirt builds up on the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoul- der belt guide with a clean, dry cloth.


c Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt assembly should be re- placed.


CHILD RESTRAINTS FOR INFANTS AND SMALL CHILDREN


WARNING


c Infants and small children should always be placed in an appropriate child restraint while riding in the ve- hicle. Failure to use a child restraint can result in serious injury or death. c Children and infants should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


c Nissan recommends that the child restraint be installed in the rear seat. According to accident statistics, children are safer when properly re- strained in the rear seat than in the front seat.


c An improperly installed child re- straint could lead to serious injury or death in an accident.


In general, child restraints are designed to be installed with a lap belt or the lap portion of a three point type seat belt.


2-30


Z X


Child restraints specially designed for infants and small children are offered by several manufacturers. When selecting any child re- straint, keep the following points in mind: 1) Choose only a restraint with a label cer- tifying that it complies with Federal Motor Vehicle Safety Standard 213 or Cana- dian Motor Vehicle Safety Standard 213. 2) Check the child restraint in your vehicle to be sure it is compatible with the vehi- cle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recommended practice J1819 for child restraint installation.


3) If the child restraint is compatible with your vehicle, place your child in the child restraint and check the various adjust- ments to be sure the child restraint is compatible with your child. Always follow all recommended procedures.


All U.S. states and provinces of Canada require that infants and small children be restrained in approved child restraints at all times while the vehicle is being operated.


WARNING


c Never install a rear-facing child re- straint in the front seat. An inflating air bag could seriously injure or kill your child. A rear-facing child re- straint must only be used in the rear seat. See ‘‘Installation on front pas- senger seat’’ for details.


c Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.


c Follow all of the child restraint manu- facturer’s instructions for installa- tion and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.


c If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.


c Adjustable seatbacks should be po- sitioned to fit the child restraint, but as upright as possible.


2-31


c After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.


c For a front-facing child restraint, if the seat position where it is installed has a 3-point type lap/shoulder belt, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoul- der belt behind the child restraint.


c When your child restraint is not in use, keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident.


CAUTION


c Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.


Z X


APD0534


PD1174


PD1331


Installation on rear seat Center lap belt When you install a child restraint in a rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. It can be placed in a forward facing or rear facing direction, depending on the size of the child. Always follow the restraint manufacturer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.


3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.


4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.


5. If it is not secure, try to tighten the belt again, or put the restraint in another seat. 6. Check to make sure the child restraint is


properly secured prior to each use.


Installation on rear outboard seating positions


WARNING


c The 3-point belt in your vehicle is equipped with a locking mode re- tractor which must be used when installing a child restraint.


c Failure to do so will result in the child restraint not being properly se- cured. It could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.


2-32


Z X


When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a forward facing or rear facing direction, depending on the size of the child. Always follow the restraint manufacturer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). reverts back to emergency locking mode when the belt is fully re- tracted.


It


4. Allow the belt to retract. A clicking sound is heard as the belt retracts. This indi- cates that the retractor is in the automatic locking mode. Pull up on the belt to remove any slack in the belt.


After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and only locks during a sudden stop or impact.


PD1332


5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.


6. Check that the retractor is in the auto- matic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retrac- tor, the belt is in the automatic locking mode.


7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.


2-33


Z X


sions listed below must be used:


Bolt diameter: 8.0 mm Bolt length: more than 1.18 in (30 mm) Thread pitch: 1.25 mm


Secure the top strap to the attaching bolt which provides the straightest installation of the top strap.


WARNING


Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


APD0107


TOP STRAP CHILD RESTRAINT If your child restraint has a top strap, it must be secured to the provided anchor point. Anchor bracket hardware must be installed. The top strap anchor bracket hardware is available through your NISSAN dealer. U.S. Part #88894-89900
Canadian Part #88894-89902
Secure the child restraint with the center lap belt or the lap portion of an outboard 3-point belt and latch the top strap hook onto the appropriate anchor bracket. To install the anchor bracket, a metric bolt of the dimen-


APD0108


Anchor point locations Anchor points are located under the rear parcel shelf finisher. To use attaching hardware for child re- straints with top straps, follow these instruc- tions carefully: 1. Open the trunk and find the anchor point nuts on the underside of the rear parcel shelf. Thread a bolt (8.0 mm diameter, 1.25 pitch) up through the nut behind the seating position where the child restraint will be installed and use it to break through the rear parcel shelf support


2-34


Z X


material. There are pre-cut circles at each anchor point location that should break away from the shelf support mate- rial when pressure is applied to them. Remove the bolt after you feel the pre-cut circle separate from the shelf support material.


2. Cut a small slit through the parcel shelf fabric at the anchor point location. Reach through the fabric with a tool such as a pair of needle-nose pliers and remove the pre-cut circle in the parcel shelf sup- port material.


3. Install the bolt through the top strap hook


and into the anchor point nut.


4. Be sure to follow all of the instructions that accompany the top strap attaching hardware.


APD0647


Installation on front passenger seat


WARNING


c Never install a rear-facing child re- straint in the front passenger seat. Supplemental air bags inflate with great force. A rear-facing child re- straint could be struck by the supple- mental air bag in a crash and could seriously injure or kill your child.


c If you install a forward-facing child restraint in the front passenger seat, place the passenger seat as far back as possible.


A child restraint with a top strap should not be used in the front passenger seat.


WARNING


c The 3-point belt in your vehicle is equipped with a locking mode re- tractor which must be used when installing a child restraint.


c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The seat could tip over or otherwise be unse- cured and cause injury to the child in a sudden stop or collision.


2-35


Z X


When you install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a forward-facing direction only. Move the seat as far back from the instrument panel as possible. Always follow the child restraint manufacturer’s instructions. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage.


PD1336


Be sure to follow the child restraint manu- facturer’s instructions for belt routing. 3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). reverts back to emergency locking mode when the belt is fully re- tracted.


It


4. Allow the belt to retract. A clicking sound is heard as the belt retracts. This indi- cates that the retractor is in the automatic locking mode. Pull up on the belt to remove any slack in the belt.


2-36


5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.


6. Check that the retractor is in the auto- matic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retrac- tor, the belt is in the automatic locking mode.


7. Check to make sure the child restraint is properly secured prior to each use. If the lap belt locked, repeat steps 3
through 6.


is not


After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and only locks during a sudden stop or impact.


Z X


TILTING STEERING WHEEL


OUTSIDE MIRROR REMOTE CONTROL


OUTSIDE MIRRORS


PD1028


APD0529


AIC0504


The driver and passenger outside mirrors are foldable. Push the outside mirror back- ward to fold it.


Tilt operation Push the lock lever down and adjust the steering wheel up or down to the desired position. Pull steering wheel in place.


the lock lever up firmly to lock the


WARNING


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


The outside mirror remote control only op- erates when the ignition switch is in the ACC or ON position. Push the right or left side of the switch to select the right or left outside mirror, then adjust using the control lever. WARNING


Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.


2-37


Z X


INSIDE MIRROR


VANITY MIRROR


PD1006M


APD0510


The night position reduces glare from the headlights of vehicles behind you at night.


WARNING


Use the night position only when nec- essary, because it reduces rear view clarity.


To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is opened.


2-38


Z X


Z X


3 Heater, air conditioner and audio system


Ventilators ..............................................................3-2
Heater and air conditioner (manual) ......................3-2
Controls ..................................................................3-3
Heater operation ....................................................3-3
Air conditioner operation (if so equipped)..............3-4
Air flow charts.........................................................3-5
Heater and air conditioner (automatic) (if so equipped) ...............................................................3-8
Radio ....................................................................3-11
Clock-radio (if so equipped).................................3-11


AM-FM radio with cassette player .......................3-12
Radio operation....................................................3-12
Cassette tape operation.......................................3-14
AM-FM radio with cassette player and compact disc player .............................................3-17
Radio operation....................................................3-17
Cassette tape operation.......................................3-19
Compact disc (CD) player operation....................3-21
Antenna ................................................................3-22
CB radio or car phone..........................................3-23


Z X


VENTILATORS


HEATER AND AIR CONDITIONER (MANUAL)


Open or close (side vents only), and adjust the air flow direction of ventilators.


HA1073


WARNING


c The air conditioner cooling function operates only when the engine is running.


3-2


AHA0527


c Do not


leave children, unreliable adults, or pets alone in your vehicle. On hot sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possi- bly fatal injuries to people or animals.


Z X


c Do not use the recirculation mode for long periods as it may cause the inte- rior air to become stale and the win- dows to fog up.


c Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.


turns the fan on and off, and


CONTROLS Fan control dial This dial controls fan speed. Air flow control buttons These buttons allow you to select the air flow outlets.


— Air flows from center and side


ventilators.


— Air flows from center and side


ventilators and foot outlets.


— Air flows mainly from foot outlets. — Air flows from defroster outlets


and foot outlets.


— Air flows mainly from defroster


outlets.


Temperature control lever This lever allows you to adjust the tempera- ture of the outlet air. Air recirculation button Off position: Outside air is drawn into the passenger compartment and distributed through the selected outlet. Use the off position for normal heater or air conditioner operation. On position (Indicator light on): Interior air is recirculated inside the vehicle. Push the air recirculation button to the ON position when driving on a dusty road, to avoid traffic fumes, and for maximum cool- ing when using the air conditioner. Air conditioner button (If so equipped) This button is provided only on vehicles equipped with an air conditioner. Start the engine, move the fan control dial to


3-3


the desired (1 to 4) position and push the A/C button to turn on the air conditioner. The indicator light comes on when the air conditioner is on. To stop the air condi- tioner, push the switch again. The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct heated air from the foot outlets. Some air also flows from the defroster outlets. 1. Push the air recirculation button to the off


position for normal heating.


2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Move the temperature control lever to the desired position between the middle and the HOT position.


Ventilation This mode directs outside air to the side and center ventilators.


Z X


1. Push the air recirculation button to the off


position. 2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Move the temperature control lever to the


desired position.


Defrosting or defogging This mode is used to defrost/defog the windows. 1. Push the 2. Move the fan control dial to the desired


button in.


position.


3. Move the temperature control lever to the desired position between the middle and the HOT position.


c To quickly remove ice or fog from the windows, turn on the fan control dial to 4
and the temperature control lever to the full HOT position.


c When the


switch is pushed, the air conditioner automatically turns on to de- fog the windshield, and the air recircula- tion mode automatically turns off.


Outside air is drawn into the passenger compartment to improve the defogging performance.


Bi-level heating/cooling This mode directs air from the side, center and foot outlets. 1. Push the air recirculation button to the off


position. 2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Move the temperature control lever to the


desired position.


Heating and defogging This mode heats the interior and defogs the windshield. 1. Push the 2. Move the fan control dial to the desired


button in.


position.


3. Move the temperature control lever to the desired position between the middle and the HOT position.


3-4


Operating tips c Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater op- eration.


c When the


or


switch is se- lected, the air recirculation mode auto- matically turns off. Outside air is drawn into the passenger compartment to improve the defogging performance.


AIR CONDITIONER OPERATION (If so equipped) Start the engine, move the fan control dial to the desired (1 to 4) position and push in the A/C button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function op- erates only when the engine is running.


Z X


Cooling This mode is used to cool and dehumidify. 1. Push the air recirculation button to the off


position. 2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Move the temperature control lever to the


desired position.


c For quick cooling when the outside tem- perature is high, push the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal cooling.


Dehumidified heating This mode is used to heat and dehumidify. 1. Push the air recirculation button to the off


position. 2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Move the temperature control lever to the


desired position.


Dehumidified defogging This mode defogs the windows and dehu- midifies. 1. Push the 2. Move the fan control dial to the desired


button in.


position.


3. Push the air conditioner button. The indi-


cator light comes on.


4. Move the temperature control lever to the


desired position. When the button is pushed, the air conditioner automatically turns on to de- fog the windshield, and the air recircula- tion mode automatically turns off.


Outside air is drawn into the passenger compartment to improve the defogging per- formance. Operating tips c Keep the windows and sun roof closed while the air conditioner is in operation.


3-5


c After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.


c The air conditioner system should be operated for about ten minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication. the coolant


temperature gauge ex- ceeds the H (hot) position, turn the air conditioner off. See ‘‘If your vehicle over- heats’’ in the ‘‘In case of emergency’’ section for additional information.


c If


AIR FLOW CHARTS The charts on the following pages show the switch and lever positions for MAXIMUM and QUICK heating, cooling, or defrosting.


Z X


3-6


AHA0528


Z X


3-7


AHA0529


Z X


HEATER AND AIR CONDITIONER (AUTOMATIC) (If so equipped)


WARNING


c The air conditioner cooling function operates only when the engine is running. c Do not


leave children, unreliable adults, or pets alone in your vehicle. On hot sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.


AHA0534


c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.


c Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.


Controls Start the engine and operate the controls to activate the climate control system. Push the OFF switch to turn the system off.


3-8


The air conditioner cooling function op- erates only when the engine is running. Cooling and/or dehumidified heat- ing (AUTO mode) This mode may be used throughout the year as the system automatically works to main- tain the customer-selected temperature. Air flow distribution and fan speed are also controlled automatically. 1. Push the AUTO switch on. AUTO and the previously selected temperature appear in the display.


2. Push the temperature set button to set the desired temperature.


or


c Adjust


the temperature to about 75°F


(24°C) for normal operation.


c The temperature of the passenger com- partment is maintained automatically. Air flow distribution and fan speed are also controlled automatically. Heating (ECON mode) The ECON (economy) mode provides cli- mate control without activating the air con- ditioner. When only heating of the passen- ger compartment is desired, use this mode.


Z X


1. Push the ECON switch on. ECON ap-


pears in the display.


2. Push the temperature set button to set the desired temperature.


or


c The temperature of the passenger com- partment is maintained as selected by the temperature set button. Air flow dis- tribution and fan speed are also con- trolled automatically in an effort to reach the desired termperature.


c Do not select a temperature setting lower than the outside air temperature. Due to the absence of air conditioner operation, the selected interior temperature may not be reached.


c ECON mode is not recommended if the windows are fogging up. If the windows begin to fog up while using the ECON mode, use the procedures outlined in ‘‘Dehumidified defogging’’. Dehumidified defogging 1. Push the


switch on. The indicator


light comes on.


2. Push the temperature set button


to set the desired temperature.


or


c To quickly remove ice or fog from the outside of the windows, push the manual fan control switch and set to the maxi- mum position


c As soon as possible after the windshield is clean, push the AUTO switch to return to the auto mode.


c When the


switch is pushed, the air conditioner automatically turns on at out- side temperatures above 35°F (2°C) to defog the windshield, and the air recircu- lation mode automatically turns off. Outside air is drawn into the passenger compartment to improve the defogging performance.


Manual fan speed control Push the fan control switches to manually control the fan speed. Each fan speed is indicated by the shading of a fan blade on indicates the display. For example, that the fan is operating at low speed and indicates that the fan is operating at


medium-high speed. c Push the AUTO switch to return to auto-


matic control of the fan speed.


3-9


Air recirculation switch Push the air recirculation switch to recircu- late interior air inside the vehicle. The indi- cator light comes on. Push it again to draw outside air into the passenger compartment. The indicator goes out. c The air recirculation mode cannot be mode has


activated when the been selected.


Manual air flow control Pushing the manual air flow control switch selects the air outlet.


— Air flows from center and side


ventilators.


— Air flows from center and side


ventilators and foot outlets.


— Air flows mainly from foot outlets. — Air flows from defroster outlets


and foot outlets.


— Air flows mainly from defroster


outlets.


Z X


Operating tips c When the engine coolant


temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 180 seconds. This is not a malfunction. After the cool- ant temperature warms up, the air flows from the foot outlets normally.


Servicing air conditioner The air conditioner system in your NISSAN vehicle is charged with a refrigerant de- signed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See ‘‘Air conditioner system refrigerant and lubricant recommen- dations’’ in the ‘‘Technical and consumer information’’ section of this manual. Your NISSAN dealer is able to service your environmentally conscious air conditioner system.


AHA0501


The sensor on the instrument panel helps maintain a constant temperature; do not put anything on or around this sensor.


3-10


Z X


RADIO


influences.


To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. CLOCK-RADIO (If so equipped) On vehicles equipped with an AM-FM radio and cassette player, a clock is integrated into the audio system. For further details, refer to ‘‘Clock Operation’’ later in this sec- tion.


3-11


Z X


AM-FM RADIO WITH CASSETTE PLAYER RADIO OPERATION Push the ON-OFF/VOL knob to turn the radio on. Push the ON-OFF/VOL knob once more to turn the radio off. Turn the knob to adjust the volume. Inserting a cassette tape into the cassette player while the radio is on turns the radio off and turns the cassette player on. Pushing the ON-OFF/VOL knob while a cassette tape is playing turns the cassette player off. Clock Operation Pressing the CLOCK button alternates the clock and the radio/cassette tape options in the display. Clock Set Depressing the CLOCK and the together CLOCK and utes.


buttons hours. Depressing the buttons together sets min-


sets


AHA0626


3-12


Z X


Clock Priority Mode In this mode the clock is shown in the display. If any radio or cassette tape func- tions are activated, the radio (or cassette tape) display illuminates for ten seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. Radio/Cassette Tape Priority Mode In this mode, the radio station illuminates in the display during radio operation. During cassette tape operation, TAPE illuminates in the display. Selecting the desired band Push the band select button (FM/AM) to change from AM to FM reception. The stereo indicator glows during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.


Tuning


WARNING


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


Manual tuning

Loading...
x