15. Remove the passenger air bag bolt (A).
16. Remove the remaining instrument panel screws (A).
ALJIA0030ZZ
ALJIA0031ZZ
ALJIA0037ZZ
17. Disconnect the audio harness connector located near the RH A-pillar. 18. Lift the instrument panel high enough in order to disconnect all the necessary harness connectors, then
remove the instrument panel.
INSTALLATION Installation is in the reverse order of removal. (cid:127) If replacing the Instrument panel transfer all the necessary parts to the new instrument panel.
Revision: September 2009
IP-13
2010 Altima
IP
CENTER CONSOLE ASSEMBLY
< ON-VEHICLE REPAIR > CENTER CONSOLE ASSEMBLY Removal and Installation
INFOID:0000000005789627
REMOVAL CAUTION: Be careful not to scratch center console finishers and other parts. 1. Move shift lever into the drive (D) position (CVT) or neutral position (M/T), then remove shift lever handle. Refer to TM-252, "Removal and Installation" (CVT: RE0F09B), TM-424, "Removal and Installation" (CVT: RE0F10A), TM-22, "Removal and Installation" (6M/T: RS6F52A).
2. Remove the cluster lid D (1).
3. Release the clips using a suitable tool, then lift the CVT or M/T finisher upward to remove. Refer to TM-
252, "Removal and Installation".
4. Remove the storage bin (1).
ALJIA0036ZZ
5. Remove both instrument side masks (1).
ALJIA0017ZZ
ALJIA0018ZZ
Revision: September 2009
IP-14
2010 Altima
CENTER CONSOLE ASSEMBLY
< ON-VEHICLE REPAIR > 6. Open the fuse block cover, remove the instrument lower cover
screw (A), then remove the instrument lower cover (1). Disconnect the asperator tube and the harness connectors.
7. Remove both the console side finishers. 8. Remove the console upper screws (A).
9. Remove the console side screws (A).
10. Position both RH and LH front seats forward. 11. Remove both the console rear screw covers, then remove the
rear screws (A), then remove the console assembly.
INSTALLATION Installation is in the reverse order of removal.
IP
ALJIA0019ZZ
ALJIA0022ZZ
ALJIA0023ZZ
ALJIA0024ZZ
Revision: September 2009
IP-15
2010 Altima
CLUSTER LID A
< ON-VEHICLE REPAIR > CLUSTER LID A Removal and Installation
REMOVAL 1. Remove instrument side mask LH.
2. Open the fuse block cover, remove the instrument lower cover
screw (A), then remove the instrument lower cover LH (1).
3. Remove the steering column cover screws (A), then remove both the steering wheel column upper (1) and lower (2) covers. NOTE: Shown with steering wheel removed for clarity. If necessary, rotate steering wheel to access steering column cover screws (A).
4. Release the clips and remove the cluster lid A (1), then discon-
nect the harness connectors.
INFOID:0000000005806135
ALJIA0018ZZ
ALJIA0019ZZ
ALJIA0025ZZ
ALJIA0026ZZ
INSTALLATION Installation is in the reverse order of removal.
Revision: September 2009
IP-16
2010 Altima
CENTER CONSOLE ASSEMBLY
< DISASSEMBLY AND ASSEMBLY > DISASSEMBLY AND ASSEMBLY CENTER CONSOLE ASSEMBLY Exploded View
INFOID:0000000005434174
1. M/T finisher 4. Console 7.
Console rear finisher (with rear duct)
2. CVT finisher 5. Console screw cover (LH) 8.
Console rear finisher (without rear duct)
Storage bin (if equipped)
3. 6. Console floor bracket 9. Console lid assembly bracket
10. Console lid assembly
11. Cup holder CVT
Clip
Pawl
12. Cup holder M/T
Metal clip
AWJIA0493ZZ
Disassembly and Assembly
INFOID:0000000005434175
DISASSEMBLY 1. Remove the console assembly. Refer to IP-14, "Removal and Installation".
Revision: September 2009
IP-17
2010 Altima
IP
CENTER CONSOLE ASSEMBLY
< DISASSEMBLY AND ASSEMBLY > 2. Remove the cup holder screws and then remove the cup holder assembly. 3. Remove the console lid screws and remove the console lid. 4. Remove the console rear finisher. 5. Remove the console lid assembly bracket. 6. Remove the power socket from the console. Refer to PWO-5, "Removal and Installation". ASSEMBLY Assembly is in the reverse order of disassembly.
Revision: September 2009
IP-18
2010 Altima