2009 Hyundai Tucson Owners Manual

55

B280A01A-AAT

FUEL GAUGE

B330A03A-AAT

TACHOMETER

B300A01A-AAT

SPEEDOMETER

OJM019017
The needle on the gauge indicates the approximate fuel level in the fuel tank. The fuel capacity is given in Section 9.

The tachometer registers the speed of your engine in revolutions per minute (rpm).

B330A01JM

B300A01JM Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilometers per hour (on the inner scale).

CAUTION:

The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.

1FEATURES OF YOUR HYUNDAI 56

TRIP COMPUTER

B310B02JM-GAT

ODOMETER/TRIP ODOMETER

B400B02JM-GAT

(If installed)

Trip Computer Switch

(AT)

(MT)

(2)

(1)

(2)

(1)

(AT)

(MT)

(1)

(1)

B310B01JM-2

B310B02JM-C

Odometer (1) The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for mainte- nance intervals.

NOTE: Any alteration of the odometer may void your warranty coverage.

Trip odometer (2) o This mode indicates the drive distance travelled since the last drive time reset. o You can choose the TRIP A or TRIP B by pressing the trip odometer switch for less than 1 second.

The trip computer is a microcomputer- controlled driver information gauge that displays information related to driving, such as a tripmeter, distance to empty, average fuel consumption average speed, and drive time on the LCD.

Odometer (1) The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for mainte- nance intervals.

HJM2185
Pushing in the trip computer switch behind the right side of the steering wheel changes the display as follows;

TRIPMETER A

TRIPMETER B

DISTANCE TO EMPTY

AVERAGE FUEL CONSUMPTION

AVERAGE SPEED

DRIVE TIME

1. Tripmeter

2. Distance to Empty

Tripmeter

Distance to Empty

FEATURES OF YOUR HYUNDAI

57

HJM2186-C o This mode indicates the total distance travelled since the last tripmeter reset. Total distance is also reset to zero if the battery is disconnected.

o Pressing the trip computer switch for more than 1 second, when the tripmeter is being displayed, clears the tripmeter to zero.

o The meter's working range is from 0.0

to 999.9 miles.

o You can choose the TRIP A or TRIP B.

HJM2187-B o This mode indicates the estimated dis- tance to empty from the current fuel in the fuel tank and distance to empty symbol.

o When refueling with more than 1.6 gal- lons (6 liters), the trip computer will recognize refueling.

o For an accurate distance to empty, drive

more than 30 miles.

o When the distance to empty is less than 30 miles, the symbol will flash and the distance to empty digits will indicate "- --" until more fuel is added.

NOTE: o The distance to empty can differ from the actual tripmeter according to driv- ing conditions.

o The distance to empty can vary ac- cording to the driving conditions, driv- ing pattern or vehicle speed.

1FEATURES OF YOUR HYUNDAI 58

3. Average Fuel Consumption

4. Average Speed

5. Drive Time

Average Fuel Consumption

Average Speed

Drive Time

MPH

B400B02JM-C o This mode calculates the average fuel consumption from the total fuel used and the distance since the last average consumption reset.

o The total fuel used is calculated from the

fuel consumption input.

o For an accurate calculation, drive more

o The meter's working range is from 0.1 to

than 30 miles.

199.9 MPG.

HJM2187-A o This mode indicates the average speed

since the last tripmeter reset.

o Even if the vehicle is not in motion, the average speed keeps going while the engine is running.

o The meter’s working range is from 0 to

999 MPH.

o Press the trip computer switch for more than 1 seconds, when the average speed is being displayed, clears the average speed to "---".

HJM2187-C

o This mode indicates the drive time since

the last tripmeter reset.

o Even if the vehicle is not in motion, the drive time keeps going while the engine is running.

o The meter’s working range is from 0:00

to 99:59.

o Press the trip computer switch for more than 1 second, when the drive time is being displayed, clears the drive time to zero.

MULTI-FUNCTION SWITCH

LIGHT

B340A01A-AAT

COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center posi- tion and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned-out fuse or bulb or see your Hyundai dealer.

B340B01A-AAT

Lane Change Signal

B340C04A-AAT

Headlight Switch

FEATURES OF YOUR HYUNDAI

59

OJM019025
To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.

OJM019026
To operate the headlights, turn the barrel on the end of the multi-function switch. The first position turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights.

NOTE: The ignition must be in the "ON" position to turn on the headlights.

1FEATURES OF YOUR HYUNDAI 60

Parking Light Auto Cut o The purpose of this feature is to prevent

the battery from being discharged. The system automatically turns off the headlights and parking lights when the driver removes the ignition key and opens the driver- side door.

o With this feature, the parking light will be turned off automatically if the driver parks on the side of road at night. If necessary, to keep the lights on when the ignition key is removed, perform the following : 1) Open the driver-side door. 2) Turn the parking lights OFF and ON again using the light switch on the steering column.

B340D01A-AAT

High-beam Switch To turn on the headlight high beams, push the lever forward (away from you). The High Beam Indicator Light will come on at the same time. For low beams, pull the lever back toward you.

B340E01A-AAT

Headlight Flasher

B340G01L-GAT

Auto Light (If installed)

OJM019027
To flash the headlights, pull the switch lever toward you, then release it. The head- lights can be flashed even though the headlight switch is in the "OFF" position.

OJM019028
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automatically on or off ac- cording to external illumination.

WINDSHIELD WIPER AND WASHER SWITCH

B350A02JM-AAT

Windshield wiper/washer

A : Wiper speed control

· MIST – Single wipe · OFF – Off · INT – Intermittent wipe · LO – Low wiper speed · HI – High wiper speed

B : Intermittent wipe time adjustment

C : Wash with brief wipes

D : Rear wiper/washer control – Spraying washer fluid

· · OFF – Off · ON – Intermittent wipe after some nor-

mal wipe

– Wash with brief wipe

B350A07JM-U

Rear window wiper/washer (If installed)

·

B350A09JM-U

FEATURES OF YOUR HYUNDAI

61

B350A02A-AAT

Windshield wipers

Fast

Slow

B350A11JM-U Operates as follows when the ignition switch is turned ON.

MIST: For a single wiping cycle, push the lever upward and release it with the lever in the OFF position. The wip- ers will operate continuously if the lever is pushed upward and held.

OFF : Wiper is not in operation INT : Wiper operates intermittently at the same wiping intervals. Use this mode in a light rain or mist. To vary the speed setting, turn the speed control knob.

LO : Normal wiper speed HI

: Fast wiper speed

1FEATURES OF YOUR HYUNDAI 62

NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accu- mulations of snow or ice. Accumulated snow and ice should be removed manu- ally. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper or activate the wind- shield wiper blade deicer.(If installed)

B350B01JM-GAT

Windshield Washer Operation

Mist Wiper Operation

B350B06JM-U

If a single wipe is desired in mist, push the windshield wiper and washer control lever upwards.

B350B05JM-U

To use the windshield washer, pull the wiper/washer lever toward the steering wheel. When the washer lever is operated, the wipers automatically three passes across the windshield. The washer continues to operate until the lever is released.

NOTE: o Do not operate the washer more than 15 seconds at a time or when the fluid reservoir is empty.

o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers. o In areas where water freezes in win- ter, use windshield washer antifreeze.

B350C01O-GAT

Adjustable Intermittent Wiper Opera- tion

B390A02JM-AAT

Rear Window Wiper And Washer (If installed)

FEATURES OF YOUR HYUNDAI

63

NOTE: Do not operate the washer continuously for more than 15 seconds or when the fluid reservoir is empty; this could dam- age the system. Do not operate the wiper when the window is dry; this can result in scratching as well as premature wiper blade wear.

B350C03JM-U

B390A03JM-U

To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval be- tween wipes can be varied from approxi- mately 1 to 18 seconds by turning the interval adjuster barrel.

: The rear window wiper starts to op- erate three times after the washer fluid sprays onto the rear window.

OFF : Wiper is not in operation ON : Intermittent wiper operation after

some normal wiper operation.

: The washer fluid will be sprayed onto the rear window and the wiper operates while the rear window wiper barrel is placed in this posi- tion.

1FEATURES OF YOUR HYUNDAI 64

FRONT FOG LIGHT SWITCH

HAZARD WARNING SYSTEM

B360A04A-AAT

(If installed)

B370A01A-AAT

WINDOW DEFROSTER SWITCH

B385A01JM-AAT

Windshield wiper Blade De-icer (If installed)

OJM019020
To turn on the front fog lights, push the switch. They will light when the headlight switch is in the second position and the ignition key is in the "ON" position.

NOTE: If you turn on the headlight high beams, the front fog lights will be turned off.

OJM019009
The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push the switch a second time.

OJM019011

The windshield wiper blade de-icer is turned on by pushing in the switch. To turn the de-icer off, push the switch a second time. The windshield wiper blade de-icer automatically turns itself off after about 20
minutes.

B380A02Y-AAT

Rear Window Defroster Switch

NOTE: The engine must be running for the rear window defroster to operate.

FEATURES OF YOUR HYUNDAI

65

AUX OUTLET

B380A02Y-AAT

(if installed)

HJM2104

The rear window defroster and heated outside rearview mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window defroster automatically turns itself off after about 15 minutes. To restart the defroster cycle, push in the switch again after it has turned itself off.

OJM019012

You can use an aux outlet to connect an audio device.

NOTE: When using a portable audio device con- nected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.

CAUTION:

Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster ele- ments.

1FEATURES OF YOUR HYUNDAI DIGITAL CLOCK 66

INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)

CIGARETTE LIGHTER

B400A02A-AAT

B410A01A-AAT

B420A01A-AAT

HJM2137
There are three control buttons for the digital clock. Their functions are:

HOUR - Push "H" to advance the hour indicated. MIN - Push "M" to advance the minute indicated. RESET -Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:

Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.

Push the "R" button for 5 seconds to dis- play a 12- or 24-hour clock (If installed).

B410A01JM The instrument panel lights can be made brighter or dimmer by turning the instru- ment panel light control knob.

B420A01JM For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai re- placement or its approved equivalent.

FEATURES OF YOUR HYUNDAI

ASHTRAY / COIN TRAY

B430A02JM-AAT

67

OJM019013
The front ashtray/coin tray may be opened by pulling the ashtray lid. To remove the ashtray to empty or clean it, lift the ashtray upward and pull it out. The ashtray coin tray light will only illuminate when the external lights are on.

CAUTION:

o Use when the engine is running and remove a plug from the power outlet after using the electric appliance. Using when the engine stops or re- maining the electric appliance with plugged in for many hours may cause the battery to be discharged.

o Do not use the power outlet to connect electric accessories or equipment other than those designed to operate on 12 volts.

o Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and malfunctions in other electronic systems or devices used in your ve- hicle.

POWER OUTLETS

B500D04JM-GAT

(If installed) Center

Rear

OJM019021

OJM019015
These supply 12V electric power to oper- ate electric accessories or equipment only when the key is in the "ON" or "ACC" position.

1FEATURES OF YOUR HYUNDAI DRINK HOLDER 68

B450A01JM-AAT

Front Drink Holder

B450B01JM-AAT

REAR DRINK HOLDER (If installed)

SUNROOF

B460A01Y-AAT

(If installed) Sun Shade

OJM019014
The front drink holder is located on the main console .

WARNING:

o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passen- gers. Spilled liquids can damage inte- rior trim and electrical components. o Do not place objects other than cups or cans in the drink holder. The ob- jects can be thrown out in the event of a sudden stop or an accident, possi- bly injuring the passengers in the vehicle.

HJM2160
The rear drink holders is located in the rear seat arm rest. The rear drink holder can be used by pulling the rear seat armrest.

! WARNING:

Do not place objects other than cups or cans in the drink holder. This objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

HJM2029
Your HYUNDAI is equipped with a sliding sunshade which you can manually adjust to let in light with the sunroof closed, or to block sunlight.

WARNING:

Never adjust the sunshade while driv- ing.

B460B02JM-GAT

Opening the Sunroof

HJM2025
If your vehicle is equipped with this feature, you can slide or tilt your sunroof with the sunroof control buttons located on the overhead console. The sunroof can only be opened, closed, or tilted when the ignition switch is in the "ON" position.

Sliding the sunroof Auto slide open To use the autoslide feature, momentarily (more than 1 second) press the SLIDE OPEN button on the overhead console. The sunroof will slide all the way open. To stop the sunroof sliding at any point, press any sunroof control button.

Manual slide open Press the SLIDE OPEN button on the over- head console for less than 0.5 second.

Auto slide close To close the sunroof, press the CLOSE button on the overhead console for more than 1 second. The sunroof will slide all the way close. To stop at the desired point, press any sunroof control button.

Auto Reverse If an object or part of the body is detected while the sunroof is closing automatically, it will reverse direction, and then stop. Auto reverse function does not work if a tiny obstacle is blocked between the sliding glass and the sunroof sash. You should always check that all passengers and objects are away from the sunroof before closing it.

WARNING:

Be careful that someone’s head, hands and body are not trapped by a closing sunroof.

FEATURES OF YOUR HYUNDAI

69

Manual slide close To close the sunroof, press the CLOSE button on the overhead console and hold it until the sunroof is closed.

! WARNING:

o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.

o Do not place your head or arms out of

the sunroof opening at any time.

o While the vehicle is moving, always keep the head, hands and other parts of the body of all occupants away from the roof opening. Otherwise, you could be seriously injured if the ve- hicle stops suddenly or if the vehicle is involved in an accident.

CAUTION:

o Do not open the sunroof in severely cold temperature or when it is cov- ered with ice or snow.

o Periodically remove any dirt that may have accumulated on the guide rails. o Do not press any sunroof control but-

ton longer than necessary. Damage to the motor or system com- ponents could occur.

1FEATURES OF YOUR HYUNDAI 70

B460C01JM-AAT

Tilting the Sunroof

Close To close the sunroof, press the CLOSE button on the overhead console and hold it until the sunroof is closed.

NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.

HJM2024

Auto tilt open To use the autotilt feature, momentarily (more than 1 second) press the TILT UP button on the overhead console. The sunroof will tilt all the way open. To stop the sunroof tilting at any point, press any sunroof control button.

Manual tilt open Press the TILT UP button on the overhead console for less than 0.5 second.

B460E02JM-GAT

Resetting the sunroof Whenever the vehicle battery is disconnected or discharged, you have to reset your sunroof system as follows:

1. Turn the ignition key to the ON position. 2. According to the position of the sunroof,

do as follows. 1) In case that the sunroof has closed completely or been tilted : Press the TILT UP button for 1 second.

2) In case that the sunroof has slide- opened: Press and hold the CLOSE button for more than 5 seconds until the sunroof has closed completely. And then press the TILT UP button for 1 second

3. Then, release it. 4. Press and hold the TILT UP button once again until the sunroof has returned to the original position of TILT UP after it is raised a little higher than the maximum TILT UP position. When this is com- plete, the sunroof system is reset.

CAUTION:

If the sunroof is not reset, it may not operate properly.

INTERIOR LIGHT

B480B01JM-AAT

Map Light Without Sunroof

With sunroof

HJM2099
Push in the map light switch to turn the light on or off. This light is convenient as a map light at night or as a personal light for the driver and the passenger.

FEATURES OF YOUR HYUNDAI

SPECTACLE CASE

71

B490A02JM-AAT

INTERIOR LIGHT

B491A03O-GAT

(If Installed)

HJM2100
The interior courtesy light has two buttons. The two buttons are: o DOOR In the "DOOR" position, the interior cour- tesy light comes on when any door is opened regardless of the ignition key po- sition. The light goes out after 30 seconds if the door is closed. When a door is unlocked by the transmit- ter, the interior light stays on for 30 seconds as long as the door is not opened. o ON In the "ON" position, the light stays on at all times. Do not leave this button pressed for an extended period of time when the ve- hicle is not running.

HJM2158
The spectacle case is located on the front overhead console. Push the end of the cover to open the spectacle case.

WARNING:

Do not keep objects except spectacle inside the spectacle case. Such objects can be thrown out in the event of a sud- den stop or an accident, possibly injur- ing the passengers in the vehicle.

1FEATURES OF YOUR HYUNDAI 72

GLOVE BOX

B500A01S-AAT

CENTER CONSOLE COMPARTMENT

B505A02NF-GAT

Center Console Box

B500B01O-AAT

Illuminated Glove Box (If installed) Opening the glove box will automatically turn on the light when the multi-function switch is turned to the first/second position.

HJM2145

o To open the glove box, pull on the glove

box release lever.

o The glove box door can be locked (and

unlocked) with the key. (If installed)

WARNING:

To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.

HJM2146

(1)

(2)

HJM2146-1
The center console box is used for storing cassette tapes or small articles. To use the center console box, pull up the handle (1) or (2) lift the lid as shown.

! WARNING:

To avoid the possibility of injury in case of an accident or a sudden stop, the center console box lid should be kept closed when the car is in motion.

B505B01NF-GAT

Center Console Armrest (If Installed)

FEATURES OF YOUR HYUNDAI

73

! WARNING:

Do not place cups or cans in the drink holder when the console box lid is used as an armrest. It may result in spilling the beverage. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electric components.

HJM2147
The center console box can be used as armrest. To use the console armrest, pull out the console box lid by pulling up the handle as shown.

NOTE: When not in use, always be sure it is locked in position properly.

1FEATURES OF YOUR HYUNDAI 74

OUTSIDE REARVIEW MIRROR

B510A01A-AAT

Manual Type

CAUTION:

If the mirror control is jammed with ice, do not attempt to break it free using the control handle or by manipulating the face of the mirror. Use an approved spray de-icer (not radiator antifreeze) to release the frozen mechanism or move the vehicle to a warm place and allow the ice to melt.

B510A01JM The outside rearview mirrors are equipped with a remote control for your convenience. It is operated by the control lever in the bottom front corner of the window. Before driving away, always check that your mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind your vehicle. When using the mirror, always exercise caution when attempting to judge the dis- tance of vehicles behind or along side of you.

B510B01Y-AAT

Electric Type (If installed)

HJM2073

The outside rearview mirrors can be ad- justed to your preferred rear vision, both directly behind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mir- ror switch controls the adjustments for both right and left outside mirrors.

To adjust the position of either mir- ror: 1. Move the selecting switch to the right or left to activate the adjustable mecha- nism for the corresponding door mirror. 2. Adjust mirror angle by depressing the appropriate perimeter switch as illus- trated.

FEATURES OF YOUR HYUNDAI

75

B510D01Y-AAT

OUTSIDE REARVIEW MIRROR HEATER (If installed)

B510C01A-AAT

FOLDING THE OUTSIDE REARVIEW MIRRORS

CAUTION:

o Do not operate the switch continu- ously for an unnecessary length of time.

o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved de-icer.

! WARNING:

Be careful when judging the size or dis- tance of any object seen in the passen- ger side rear view mirror. It is a convex mirror with a curved surface. Any ob- jects seen in this mirror are closer than they appear.

HJM2104
The outside rearview mirror heater is actu- ated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrosting or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automati- cally turns itself off after 15 minutes.

B510C01JM To fold the outside rearview mirrors, push them toward the rear. The outside rearview mirrors can be folded rearward for parking in narrow areas.

WARNING:

Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control, and an accident which could cause serious in- jury or death.

1FEATURES OF YOUR HYUNDAI 76

DAY/NIGHT INSIDE REARVIEW MIRROR

B520A01A-AAT

Manual Type

B520C04JM-AAT

AUTOMATIC DIMMING REAR VIEW MIRROR WITH COMPASS (If installed)

HJM2070

Your Hyundai is equipped with a day/night inside rearview mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.

B520C08JM

1. Status Indicator LED 2. Feature Control Button 3. Rear Light Sensor 4. Display Window

Automatic dimming rear view mirror con- trols automatically the glare of headlights of the car behind you when it turned on by pressing and holding the button for more than 3 but less than 6 seconds. It is turned off by pressing and holding the button for same time once more.

1. To operate Compass feature Press and release the button, then the vehicle's directional heading will be dis- played. Pressing and releasing the button again will turn off the display. Heading display - E : East - W : West - S : South - N : North ex) NE : North East

2. Calibration procedure Press and hold the button for more than 9
but less than 12 seconds. When the com- pass memory is cleared a "C" will appear in the display.

- Driving the vehicle in a circle at less than 5mph 2 times or until the compass heading appears.

- Driving in a circle in right-handed direc- tion and opposite direction are pos- sible, and if the calibration is completed, the compass heading will appear.

- Keep driving in a circle until a compass

heading appears.

3. Setting the compass zone 1. Find your current location and variance

zone number on the zone map.

4. Changing Mirror Angle setting

(If Installed):

Due to mirror positions being angled to- wards the driver, the compass mirror can also compensate for drivers seated on the Left Hand side of the vehicle (steering wheel on the LH side of the vehicle) or Right Hand side of the vehicle (steering wheel on the RH side of the vehicle).

B520C06JM

2. Press and hold the button for more than 6 but less than 9 seconds. The current zone number will appear in the display. 3. Press the button until the new zone number appears in the display. After you stop pressing the button in, the display will show a compass direction within a few seconds.

To adjust the Left Hand, “L” or Right Hand, “R”, setting: 1. Press and hold the button for more than

12 seconds.

2. Release then press the button to toggle

between “L” and “R”.

NOTE: This procedure also causes the com- pass to be de-calibrated.

3. To re-calibrate the compass, drive the vehicle in 2 complete circles at less than 8km/h (5mph).

FEATURES OF YOUR HYUNDAI

77

CAUTION:

1. Do not install the ski rack, antenna, etc. which are attached to the vehicle by means of a magnet. They affect the operation of the compass.

2. If the compass deviates from the cor- rect indication soon after repeated adjustment, have the compass checked at an authorized dealer.

3. The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct compass point when the vehicle moves to an area where the geomag- netism is stabilized.)

4. When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.

1FEATURES OF YOUR HYUNDAI PARKING BRAKE 78

B530A02A-AAT

CAUTION:

Driving with the parking brake applied will cause excessive brake pad (or lin- ing) and brake rotor wear.

Releasing the parking brake To release the parking brake, first apply the foot brake and pull the parking brake lever slightly. Secondly, depress the re- lease button and lower the parking brake lever while holding the button.

HJM3026

Applying the parking brake To engage the parking brake, first apply the foot brake and then without pressing the release button in, pull the parking brake lever up as far as possible. In addition it is recommended that when parking the ve- hicle on a gradient, the shift lever should be positioned in the appropriate low gear on manual transaxle vehicles or in the P (Park) position on automatic transaxle ve- hicles.

TAIL GATE

B540A01JM-AAT

OJM019023

o Pull and raise the "DOOR" release lever

to open the tail gate.

o To close, lower the door, then press down on it until it locks. To be sure the door is securely fastened, try to pull it up again.

WARNING:

The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car result- ing in serious illness or death to the occupants. See additional warnings con- cerning exhaust gases on page 2-2.

B540B01JM-AAT

Tail gate Window

B540A01JM-AAT

SHOPPING BAG HOLDERS (If installed)

CAUTION:

o Do not hang a bag beyond 6 Ibs (3 kg). It may cause damage to the shopping bag holder.

o Return it to the original position after

using the shopping bag holder.

FEATURES OF YOUR HYUNDAI

79

(1)

(2)

OJM019024

o Pull the "GLASS" release lever (1) to open the tailgate window glass, and raise the window open lever (2).

o To close the tail gate window, lower the tail gate window, and it will close by itself. To be sure the tail gate window is se- curely fastened, try to pull it up again.

NOTE: The tail gate window lock is operated in connection with the tail gate lock. To open the tail gate window make sure the tailgate is unlocked with a key (if in- stalled) or the central door locking switch.

HJM2150

OJM019007

Shopping bag holders are located in the front console and on the backside of the rear seat. When not in use, return it to the original position.

1FEATURES OF YOUR HYUNDAI 80

HOW TO USE LUGGAGE ROOM

B640A01S-AAT

CARGO SECURITY SCREEN (If installed)

B650A01S-AAT

Stowage Precautions 1. Do not place objects on the cargo secu- rity screen. Such objects may be thrown about inside the vehicle and possibly injure vehicle occupants during an ac- cident or when braking.

2. For better fuel economy, do not carry

unnecessary weight.

3. Never allow anyone to ride in the lug- gage compartment. It is designed for luggage only.

4. Try to maintain the balance of the ve- hicle and locate the weight as far for- ward as possible.

B650A01JM

To use the security screen, pull it out of the retractor and hook it to the anchors as illustrated.

B545B02JM-GAT

Luggage Under Tray (If installed)

There is a multipurpose tray under the luggage mat.

HJM2166

Luggage Side Trim

B655A02JM-GAT

Covering screen (If Installed)

FEATURES OF YOUR HYUNDAI

81

HJM2168-1
Raise the luggage under tray cover with the grip.

B545B01JM There are small article trays in the luggage side trim.

B655A02JM Covering shelf screen veils the luggage room to hang the screen hook to a head- rest pole. While not in use, place the screen hook to the hook holder.

CAUTION:

When folding the rear seatback forward, remove the hook from the headrest pole. Otherwise, the covering screen may be damaged or malformed.

1FEATURES OF YOUR HYUNDAI 82

B540D03HP-GAT

Luggage Net (If Installed)

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when car- rying fragile or bulky objects in the lug- gage compartment.

WARNING:

Avoid eye injury. DO NOT overstretch. ALWAYS keep face and body out of its path. DO NOT use when the luggage net straps have visible signs of wear or damage.

B540D01JM Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor or at the back of the luggage compartment to pre- vent objects from sliding.

ROOF RACK

B630A01JM-AAT

(If installed)

HJM2162

If your Hyundai has a roof rack, you can load things on top of your vehicle. Crossrails and fixing components to adapt the roof rack on your vehicle may be obtained from an authorized Hyundai dealer.

CAUTION:

o In case a sunroof is installed, do not position roof rack loads that could interfere with opening of the sunroof. o The following specifications are rec- ommended when loading cargo or luggage.

HIGH-MOUNTED REAR STOP LIGHT

REMOTE FUEL-FILLER LID RE- LEASE

B550A01A-AAT

B560A03JM-AAT

FEATURES OF YOUR HYUNDAI

83

CAUTION:

ROOF RACK

165 lbs (75 kg) Evenly Distributed

o Loading cargo or luggage above 165
lbs (75 kg) on the roof rack may dam- age your vehicle. When you carry large objects, never let them hang over the rear or the sides of your vehicle.

o To prevent damage or loss of cargo as you are driving, check frequently to make sure the luggage carrier and cargo are still securely fastened.

o Always drive your vehicle at a moder-

ate speed.

o To use the roof rails as a roof rack, you must fit the roof rails with two or more crossrails or equivalent before car- rying cargo or luggage on the roof.

o Loading cargo or luggage exceeding the specification on the roof rack may reduce the stability of your vehicle. o Do not allow cargo loads to rest di- rectly on the roof of your article; cross rails must be used.

B550A01JM

In addition to the lower-mounted rear stop- lights on either side of the car, the high mounted rear stoplight in the center of the rear window also lights when the brakes are applied.

HJM2018
The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel- filler lid opener located on the front floor area on the left side of the vehicle.

NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radia- tor anti-freeze) or move the vehicle to a warm place and allow the ice to melt.

1FEATURES OF YOUR HYUNDAI 84

WARNING:

o Tighten the cap until it clicks, other-

wise the "

" light will illuminate.

o If you open the fuel filler cap during high ambient temperatures, a slight "pressure sound" may be heard. This is normal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.

o Do not "top-off" after the nozzle auto-

matically shuts off when refueling.

o Automotive fuels are flammable/ex- plosive materials. When refueling, please note the following guidelines carefully. - Before touching the fuel nozzle or fuel filler cap, have one's hands in contact with metal parts away from the filler neck to discharge static electricity.

- Do not get back in the vehicle while refueling. Do not operate anything that can produce static electricity. Static electricity discharge can ig- nite fuel vapors resulting in explo- sion.

B560A01JM

! WARNING:

o Gasoline vapors are dangerous. Be- fore refueling, always stop the engine and never smoke or allow sparks and open flames near the filler area.

o Never operate your vehicle without a filler cap properly installed, flammable vapors and gasoline could leak out in dangerous situations such as a colli- sion or rollover. If the filler cap must be replaced, only use genuine Hyundai replacement parts.

o After refueling, make sure the fuel cap is installed securely to prevent fuel spillage in the event of an acci- dent.

- When using a portable fuel con- tainer be sure to place the con- tainer on the ground while refueling. Static electricity discharge from the container can ignite fuel vapors causing a fire. While starting refuel- ing contact should be maintained until the filling is complete.

- Do not use cellular phones around a gas station. The electric current or electronic interference from cel- lular phones can ignite fuel vapors causing a fire.

- When refueling always shut the en- gine off. Sparks by electrical equip- ment of the engine can ignite fuel vapors causing a fire. After refuel- ing, check to make sure the fuel filler cap is securely closed, and then start the engine.

- Do not smoke or try to light ciga- rettes around a gas station. Auto- motive fuels are flammable.

HOOD RELEASE

B570A03A-GAT

2. Push the secondary latch lever to the

left and lift the hood.

FEATURES OF YOUR HYUNDAI

85

Before closing the hood, return the support rod to its clip to prevent it from rattling. Lower the hood until it is about 1 ft. (30 cm) above the closed position and let it drop. Make sure that it locks into place.

CAUTION:

Make sure that the support rod has been released prior to closing the hood.

1. Pull the release knob to unlatch the

hood.

HJM2020

HJM2022

WARNING:

3. Hold the hood open with the support

rod.

o Always double check to be sure that the hood is firmly latched before driv- ing away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibil- ity, which might result in an accident. o The support rod must be inserted completely into the hole provided in the hood whenever you inspect the engine compartment. This will pre- vent the hood from falling and possi- bly injuring you.

o Do not move the vehicle with the hood in the raised position, as vision is obstructed and the hood could fall or be damaged.

HJM2021

HJM2023

1FEATURES OF YOUR HYUNDAI 86

FLOOR MAT ANCHOR

SUN VISOR

B571A03Y-AAT

B580A01L-AAT

B570A01JM-A

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

WARNING:

o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the move- ment of the pedals during driving, it may cause an accident.

o Don't put an additional floor mat on the top of the anchored floor mat, other- wise the additional mat may slide for- ward and interfere with the move- ment of the pedals.

B580A02JM Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To re- duce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirror is provided on the back of the sun visor for the driver and front passenger.

NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.

! WARNING:

Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.

B580B01B-GAT

Illuminated Vanity Mirror (If installed) Opening the lid of the vanity mirror will automatically turn on the mirror light.

B585BA01JM-AAT

SUN VISOR EXTENDER

HJM2142-1
Your vehicle is equipped with sun visor extenders that may be used when the visor is in the side glass position.

STEERING WHEEL TILT LEVER

FEATURES OF YOUR HYUNDAI

FRONT DOOR EDGE WARNING LIGHT

87

B580C01LZ-AAT

TICKET HOLDER

B600A01A-AAT

B620A01S-AAT

B580C01JM The ticket holder is provided on the front of the sun visor for holding a tollgate ticket.

HJM2067

To Adjust the Steering Wheel: 1. Push the lever downward to unlock. 2. Raise or lower the steering wheel to the

desired position.

3. After adjustment, securely tighten the

lever by pulling it upward.

B620A01JM A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle which may cause serious injury or death.

1FEATURES OF YOUR HYUNDAI 88

HORN

REAR SEAT ARM REST

CRUISE CONTROL

B610A01L-GAT

B611A01Y-AAT

B660A02S-AAT

(If installed) Type A

B610A01JM Press the pad on the steering wheel to sound the horn.

HJM2043
This arm rest is located in the center of the rear seat back.

Type B

Main Switch

B660A01JM

Main Switch

B660A02JM

B660B04E-AAT

To Set the Cruise Speed Type A

The cruise control system provides auto- matic speed control for your comfort when driving on straight, open freeways, toll roads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

NOTE: Cruise control is not recommended for city driving, winding roads, slippery roads, heavy rain, or other bad weather conditions.

Type B

B660B01JM

B660B02JM

FEATURES OF YOUR HYUNDAI

89

1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illuminated. This turns the sys- tem on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h). 3. Push the cruise control switch down- ward to "SET/COAST" or "−/SET" and release it. If the "SET/COAST" or "−/ SET" switch is selected, the cruise "SET" indicator light in the instrument cluster will illuminate.

4. Remove your foot from the accelerator pedal and the desired speed will auto- matically be maintained.

5. To momently increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will re- turn to the speed you have set.

WARNING:

To avoid accidental cruise control en- gagement, keep the cruise control main switch off when not using the cruise control.

1FEATURES OF YOUR HYUNDAI 90

B660C04E-AAT

To Cancel the Cruise Speed Type A

Type B

B660C01JM

To disengage the cruise control system, pull the control switch toward the steering wheel to the "CANCEL" position. Additionally, the following actions will dis- engage the system:

B660D03E-AAT

To Resume the Preset Speed Type A

o Depress the brake pedal. o Depress the clutch pedal (Manual

transaxle).

o Shift the selector lever to "P" or "N"

position (Automatic transaxle).

o Decrease the vehicle speed to less

than 25 mph (40 km/h).

o Release the main switch.

Type B

B660D01JM

B660C02JM

B660D02JM

The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to the "RES/ ACC" or "+/RES" position and release it, providing the vehicle speed is above 25
mph (40 km/h). If the control switch "RES/ACC" or "+/RES" is selected, the cruise "SET" indicator in the instrument cluster will illuminate.

B660F05E-AAT

To Reset at a Slower Speed Type A

FEATURES OF YOUR HYUNDAI

91

1. Push the control switch downward to "SET /COAST" or "−/SET"and hold it. The vehicle will decelerate. If the "SET/COAST" or "−/SET" switch is selected, the cruise "SET" indicator light in the instrument cluster will illuminate. 2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

B660E02E-AAT

To Reset at a Faster Speed 1. Push the control switch upward to the "RES/ACC" or "+/RES" position and hold it. If the control switch "RES/ACC" or "+/ RES" is selected, the cruise "SET" indi- cator in the instrument cluster will illumi- nate.

2. Accelerate to desired speed and re- lease the control switch. While the con- trol switch is held, the vehicle will gradu- ally gain speed.

Type B

B660B01JM

B660B02JM

! WARNING:

o Keep the cruise control main switch off when not using the cruise control to avoid inadvertently setting a speed. o Use the cruise control system only when traveling on open highways in good weather.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

1FEATURES OF YOUR HYUNDAI 92

! WARNING:

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch.

o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system de- activate. This is an indication of nor- mal system operation. o During normal cruise control opera- tion, when the "SET/COAST" or "−−−−−/ SET" is activated or reactivated after applying the brakes, the cruise con- trol will energize after approximately 3 seconds. This delay is normal.

HEATING AND COOLING CONTROL

B710A01JM-GAT

1. Side Defroster Nozzle 2. Side Ventilators 3. Windshield Defroster Nozzles 4. Center Ventilators

B710A02JM

FEATURES OF YOUR HYUNDAI

9393939393

B710B02O-AAT

CENTER VENTILATOR The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

B710C02HP-AAT

SIDE VENTILATOR The side ventilators are located on each side of the dash board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are closed when the vent knob is moved to " " position. The vents are opened when the vent knob is moved to " ". Keep these vents clear of any obstructions.

1FEATURES OF YOUR HYUNDAI 94

HEATING AND VENTILATION

B670A01JM-AAT

B670B01A-AAT

Fan Speed Control (Blower Control)

B670C03E-AAT

Air Intake Control

HJM2109A

There are three controls and two switches for the heating and cooling system. They are:

1. Air flow control 2. Fan speed control 3. Temperature control 4. Air intake control switch 5. Air conditioning switch

HJM2116A

This is used to turn the blower fan on and off and to select the fan speed. The blower fan speed, and therefore the volume of air delivered from the system, may be controlled manually by setting the blower control between the "1" and "4" position.

HJM2118A This is used to select fresh outside air or recirculating inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.

RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is recirculation mode.

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function se- lected. With the "Recirculation" mode selected, air from within the passenger compart- ment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: It should be noted that prolonged opera- tion of the heating in "Recirculation" ) may result in fogging of the mode ( windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- ) selected may result lation" mode ( in the air within the passenger compart- ment becoming excessively dry.

B670D01JM-GAT

Air Flow Control

FEATURES OF YOUR HYUNDAI

9595959595

HJM2111

Face-Level

Selecting the "Face" mode will cause air to be discharged through the side and center ventilators.

HJM2110A This is used to turn the blower fan on/off and to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to rep- resent Face, Bi-Level, Floor, Floor-Defrost and Defrost air position. The MAX A/C mode is used to cool the inside of the vehicle faster. The "OFF" mode is used to turn the blower fan off.

1FEATURES OF YOUR HYUNDAI 96

HJM2114

HJM2113

HJM2112

Bi-Level

Air is discharged through the face vents and the floor vents.

Floor-Level

Air is discharged through the floor vents, windshield defroster nozzle, side defroster nozzle and side ventilator.

Floor-Defrost Level

Air is discharged through the windshield defroster nozzle, the floor vents, side de- froster nozzle and side ventilator. If the "Floor-Defrost" mode is selected, the A/C will be turned on automatically and "Fresh" mode will be activated.

FEATURES OF YOUR HYUNDAI

9797979797

NOTE: o The air intake control switch will change to " " mode when the igni- tion switch is turned "ON" with the MAX A/C mode selected.

o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.

Air Intake

Control Switch

or

A/C

ON

ON or OFF *

OFF

OFF

ON or OFF *

ON

ON

* The A/C or the air intake control switch

returns to its former setting.

HJM2115

B670C02JM