Download PDF Manual

switch off when you have a child in the car so the child does not get injured by operating the window unintentionally.


Power Windows


The master control panel also con- tains these extra features:


AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly.


To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.


The AUTO function only works to lower the driver's window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position.


Instruments and Controls


Main MenuTable of Contentsst The convertible top on your Honda lowers and raises electrically.


Do not lower or raise the top while the engine is running.


LATCH


TAB


Convertible Top


Do not operate the convertible top if the car is raised on the jack, a hoist, or on jack stands.


Lowering the Convertible Top Park your car in the shade whenever possible. Extended exposure to sunlight can cause the convertible top to deteriorate.


1. Apply the parking brake. The


convertible top will not operate unless the parking brake is fully engaged.


2. Turn the ignition switch to ON (II).


Before operating the convertible top, make sure the car is parked on level ground, and that there is enough clearance above the top.


It is advisable to raise the top whenever you park the car. This helps to protect the car from unexpected weather changes, and from theft of your valuables.


NOTICE


Do not operate the convertible top in freezing weather. You can damage the material and mechanism of the convertible top.


Do not operate the lop if it is wet, dirty, or covered with ice or snow.


Never drive the car with the convertible top half open.


LOCKING LEVER


3. There is a latch on each side. Push


in the lab and pull the locking lever down.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Convertible Top


LOCKING LEVER


LATCH


LOCKING LEVER


ROOF SWITCH


4. Push the top forward while you


release the latches from the windshield header by pushing the locking levers forward.


5. With the latches released, pull back on the locking levers and push them up until they latch.


6. Pull back and hold the ROOF


switch.


Instruments and Controls


Main MenuTable of Contentsst The windows will lower and the roof will fold back. Release the ROOF switch when the roof is retracted completely into the rear shelf.


NOTICE


Do not sit on the folded convertible top, or put heavy items on top of it.


Convertible Top


Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.


Make sure that you, your passenger or any other people around the car are clear of the way of the moving convertible top.


Instruments and Controls


Main MenuTable of Contentsst Convertible Top


Raising the Convertible Top 1. Apply the parking brake. The


convertible top will not operate unless the parking brake is fully engaged.


2. Turn the ignition switch to ON (II).


Instruments and Controls


ROOF SWITCH


3. Push the ROOF switch forward


and hold it.


4. The windows, if raised, will lower


automatically.


Main MenuTable of Contentsst WINDSHIELD HEADER


TAB


LATCH


LOCKING LEVER


Convertible Top


Operating the convertible top while any part of a passenger is in the way of the convertible top can cause serious injury.


Make sure that you, your passenger or any other people around the car are clear of the way of the moving convertible top.


The convertible top will raise. Release the ROOF switch when the top reaches the windshield header.


5. Push in the tab on each locking lever and pull the locking lever down.


NOTICE


Do not put heavy items on the closed convertible top. You can damage the material and the mechanism.


6. While pushing the convertible top


forward, push the locking lever forward and set the latch into the windshield header.


7. Pull back on the locking lever and


push it up until it latches. Make sure it is securely latched.


Instruments and Controls


Main MenuTable of Contentsst Convertible Top


Convertible Top Cover Use the convertible top cover when the top is folded to help prevent foreign objects, dirt, etc., from getting into the material and mechanism.


Instruments and Controls


1. Remove the convertible top cover


from the trunk.


2. Connect the snaps on the top


cover to the four pins on the back of the interior panel.


3. Hook the fastener string to the pin on each side wall of the passenger compartment.


Main MenuTable of Contentsst Maintenance


Convertible Top


Every three to six months, depending on how often the top is folded, rub a thin film of Shin-Etsu Silicone grease (available from your Honda dealer, P/N 08798-9013) onto the seals wherever they touch the convertible top or each other.


4. Fit deep the rear part of the top cover into the space behind the convertible top.


5. To remove the top cover, reverse


the attaching procedure.


Dust is the main cause of creaks or other sounds coming from the convertible top. Regularly clean the body seals with glass cleaner and a soft cloth. Do not use a scraper or de-icing chemicals to remove frost, snow, or ice from the top or rear window.


Instruments and Controls


Main MenuTable of Contentsst Convertible Top


To reduce the possibility of leaks:


The convertible top seals are designed to promote the flow of water off the roof. Spraying high pressure water directly on the seals can distort them, causing a leak. Use only a low pressure water stream when using a hose, and avoid car washes.


Use the door pull to open and close the door. Do not push or pull on the door glass.


Do not lean or sit on an open door.


Instruments and Controls


Main MenuTable of Contentsst Hazard Warning


Mirrors


Adjusting the Power Mirrors


SELECTOR SWITCH


Hazard Warning, Mirrors


Push the red button next to the roof switch to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.


TAB


Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.


The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the clay or night position.


ADJUSTMENT SWITCH


Adjust the outside mirrors with the adjustment switch on the driver's door armrest:


1. Turn the ignition switch ON (II).


2. Move the selector switch to L


(driver's side) or R (passenger's side).


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Mirrors, Parking Brake


Parking Brake


NOTICE


Driving the car with the parking brake applied can damage the rear brakes and axles.


3. Push the appropriate edge of the


adjustment switch to move the mirror right, left, up or down.


4. When you finish, move the


selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch.


To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 44). If you try to drive the vehicle without releasing the parking brake, the ABS indicator may come on, and the ABS may not work properly.


Instruments and Controls


Main MenuTable of Contentsst Beverage Holder


Accessory Power Socket


Beverage Holder, Accessory Power Socket


To open the beverage holder, push on the front edge.


Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passenger. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.


To use the accessory power socket, pull out on the cover. The ignition switch must be in ACCESSORY (I) or ON (II).


This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).


It will not power an automotive type cigarette lighter element.


Instruments and Controls


Main MenuTable of Contentsst Audio Panel


To open the audio panel, push on the top center and let the panel swing down. To close, pivot the panel up and push on it until it latches. Refer to page 94 for operation of the audio system.


Instruments and Controls


Main MenuTable of Contentsst Interior Lights


The interior light has a three- position switch. In the OFF position, the light does not come on. In the center position, the interior light comes on when you open either door. In the ON position, the interior light stays on continuously.


In addition, when the three position switch is in the center position with both doors closed, the two bulbs in the interior light can be turned on separately by the pushbutton switches next to them. Push the switch to turn the light on or off.


If the three-position switch is in the center position, the interior light will come on when you remove the key from the ignition switch.


Instruments and Controls


Main MenuTable of Contentsst Comfort and Convenience Features


The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions.


The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.)


Heating and Cooling........................ 86
What Each Control Does............ 80
How to Use the System............... 88
To Turn Everything Off............. 93


Audio System


AM/FM/CD Audio System....... 94
Operating the Radio.................... 95
Adjusting the Sound.................... 99
Audio System Lighting............. 100
Radio Frequencies..................... 100
Radio Reception......................... 101
Operating the CD Player.......... 102
Operating the CD Changer...... 107
Protecting Compact Discs........ 108
CD Player Error Indications..... 110
CD Changer Error


Indications.............................. 111
Remote Audio Controls ............ 112
Theft Protection........................ 113


Comfort and Convenience Features


Main Menust Heating and Cooling


Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility.


What Each Control Does


Fan Control Lever Pushing this lever up and down increases and decreases the fan speed. The indicators next to the lever show you the speed selected.


Temperature Control Dial Turning this dial clockwise increases the temperature of the air flow.


Air Conditioning (A/C) Button This button turns the air condi- tioning ON and OFF. The indicator in the button lights when the A/C is on.


Comfort and Convenience Features


MODE CONTROL DIAL


TEMPERATURE CONTROL DIAL


RECIRCULATION BUTTON


AIR CONDITIONING SWITCH


FAN CONTROL LEVER


Recirculation Button This button controls the source of the air going into the system. When the indicator in this button is lit, air from the car's interior is sent through the system again (Recircula- tion mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode).


Main MenuTable of Contentsst Heating and Cooling


Mode Control Dial Use the MODE control dial to select the vents the air flows from.


Air flows from the vents on both sides of the instrument panel, and from the dashboard vent in front of the passenger.


Air flow is divided between the vents in the dashboard and the floor vents.


Air flows from the center vents in the dashboard above the audio system, the vents on both sides of the instrument panel and from the floor vents. Select this position when you drive with the convertible top folded.


Air flows from the floor


vents and the vents on both sides of the instrument panel.


When you select automatically switches to Fresh Air mode and turns on the A/C.


the system


Air flow is divided between


the floor vents, the defroster vents at the base of the windshield and the vents on both sides of the instrument panel.


Air flows from the defroster


vents at the base of the windshield and the vents on both sides of the instrument panel.


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


Vent Controls


CENTER VENT


SIDE VENT


You can shut off the air flow from each vent by turning the dial all the way toward the mark until it clicks.


You can adjust the direction of the air coming from the vents on both sides of the instrument panel and at the corner of the dashboard on the passenger's side. To adjust the air flow up and down, move the tab in the center of each vent up and down. To adjust it left and right, turn the dial under each vent left and right.


Comfort and Convenience Features


How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting.


The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.


Main MenuTable of Contentsst It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears.


The outside air intakes for the heating and cooling system are at the base of the windshield. Keep these clear of leaves and other debris.


RECIRCULATION BUTTON


AIR CONDITIONING SWITCH


FAN CONTROL LEVER


Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents behind the seat-backs.


Heating and Cooling


MODE CONTROL DIAL


TEMPERATURE CONTROL DIAL


1. Turn the temperature control dial


all the way to the left. Make sure the A/C is off.


2. Select 3. Set the fan to the desired speed.


and Fresh Air mode.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


To Cool with A/C 1. Turn on the A/C by pressing the


button. The light in the button should come on when a fan speed is selected.


2. Make sure the temperature


control dial is all the way to the left.


3. Select 4. If the outside air is humid, select


Recirculation mode. If the outside air is dry, select Fresh Air mode. Set the fan to the desired speed.


If the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way:


1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the tempera- ture control dial is all the way to the left.


3. Set the fan to maximum speed. 4. Open the windows partially. Select


and Recirculation mode.


Comfort and Convenience Features


RECIRCULATION BUTTON


AIR CONDITIONING SWITCH


FAN CONTROL LEVER


MODE CONTROL DIAL


TEMPERATURE CONTROL DIAL


When the interior has cooled down to a more comfortable temperature, close the windows and set the controls as described for normal cooling.


Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 47) when driving in stop-and-go traffic or climbing a long, steep hill. If it moves near the red mark, turn off the A/C until the reading returns to normal.


Main MenuTable of Contentsst To Heat To warm the interior:


1. Start the engine. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with


and Fresh Air mode.


the temperature control dial.


To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.


1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control


and Fresh Air mode.


dial so the mixture of heated and cooled air feels comfortable.


Heating and Cooling


To Defog and Defrost To remove fog from the inside of the windows:


1. Switch the fan on. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


3. Adjust the temperature control


dial so the air flow from the defroster vents feels warm.


This setting is suitable for all driving conditions whenever the outside temperature is above 32° F (0°C).


When you switch to another mode from Press the A/C button to turn if off.


the A/C stays on.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


To remove exterior frost or ice from the windshield and side windows after the vehicle has been sitting out in cold weather:


MODE CONTROL DIAL


1. Start the engine. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


3. Switch the fan and temperature


controls to maximum.


To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows.


Comfort and Convenience Features


RECIRCULATION BUTTON


AIR CONDITIONING SWITCH


FAN CONTROL LEVER


TEMPERATURE CONTROL DIAL


Main MenuTable of Contentsst Heating and Cooling


These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial beside each vent. This will send more warm air to the windshield defroster vents.


For safety, make sure you have a clear view through all the windows before driving away.


To Turn Everything Off To shut off the system temporarily, turn off the fan (no lights illuminated).


You should shut the system completely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


AM/FM/CD Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.


The anti-theft feature will disable the system if it is disconnected from the vehicle's battery. To get the system working again, you must enter a code number (see page 113).


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


TUNE — Use the TUNE bar to tune the radio to a desired frequency. Press the to a higher frequency, and the


side of the bar to tune


side to tune to a lower


frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly.


SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press the SEEK bar on either the or


side, then release it.


Depending on which side you press, the system scans upward or down- ward from the current frequency. It stops when it finds a station with a strong signal.


Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob.


The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.


You can use any of four methods to find radio stations on the selected band: TUNE, SEEK, SCAN or the Preset buttons.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCAN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds. When it plays a station that you want to continue listening to, press the SCAN button again.


Preset — You can store the fre- quencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two on the FM band.


Comfort and Convenience Features


AM/FM BUTTON


STEREO INDICATOR


PWR/VOL KNOB


TUNE BAR


PRESET BUTTONS


SCAN BUTTON


SEEK BAR


Main MenuTable of Contentsst To store a frequency:


1. Select the desired band, AM or FM. FM1 and FM2 let yon store two frequencies with each Preset button.


2. Use the TUNE or SEEK function


to tune the radio to a desired station.


3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep.


4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.


Once a station's frequency is stored, simply press and release the proper Preset button to tune to it. The preset frequencies will be lost if your vehicle's battery goes dead, is disconnected, or the radio fuse is removed.


Audio System


AM/FM BUTTON


SEEK BAR


TUNE BAR


PRESET BUTTONS


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area.


To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals; It stores the frequencies of six AM stations and twelve FM stations in the preset buttons. You can then use the preset buttons to select those stations.


If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a "0" displayed when you press any preset button that does not have a station stored.


Comfort and Convenience Features


TUNE BAR


SEEK BAR


AUTO SELECT INDICATOR


SCAN BUTTON


A. SEL BUTTON


If you do not like the stations Auto Select has stored, you can store other frequencies in the preset buttons. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset buttons as described previously.


Auto Select does not erase the frequencies that you preset pre- viously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset buttons will then select the frequencies you originally set.


Main MenuTable of Contentsst Audio System


Adjusting the Sound Balance/Fader These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the side- to-side strength, while the Fader control adjusts the front-to-back strength. To adjust the f ader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it. With only two speakers, set the fader control to the maximum front setting. To adjust the balance, push on the TREBLE/BALANCE control knob to get it to pop out. Pull it out slightly farther, and adjust the side-to-side sound to your liking. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


BASS/FADER CONTROL


TREBLE/BALANCE CONTROL


Treble/Bass — Use these controls to adjust the tone to your liking.


To adjust the Treble level, push on the TREBLE/BALANCE control knob to get it to pop out. Without pulling it out farther, turn the knob to adjust the treble level. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


To adjust the Bass level, push on the BASS/FADER control knob to get it to pop out. Without pulling it out farther, turn the knob to adjust the bass level. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Audio System Lighting The audio system illuminates when the parking lights are on, even if the radio is turned off.


Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those hands cover these frequen- cies:


AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz


Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).


Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as "FM101."


Comfort and Convenience Features


Main MenuTable of Contentsst Radio Reception How well your Honda's radio receives stations is dependent on many factors, such as the distance from the station's transmitter, nearby large objects, and atmos- pheric conditions.


A radio station's signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station's signal.


Audio System


Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio's reception. You may temporarily hear both stations, or hear only the station you are close to.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.


Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.


Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one clay and not receive it the next day because of a change in conditions.


Comfort and Convenience Features


Main MenuTable of Contentsst As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Audio System


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Operating the CD Player You operate the CD player with the same controls used for the radio.


With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.


You can also play 3-inch (8-cm) discs without using an adapter ring. In all cases, play only standard round discs. Odd-shaped CDs may jam in the drive or cause other problems.


When the system reaches the end of the disc, it will return to the begin- ning and play that disc again.


Comfort and Convenience Features


AM/FM BUTTON


CD SLOT


TUNE BAR


EJECT BUTTON


CD BUTTON


RPT BUTTON


SEEK/SKIP BAR


A.SEL/RDM BUTTON


Main MenuTable of Contentsst You can switch to the radio while a CD is playing by pressing the A M/ FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off.


If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.


Press the eject button to remove the disc from the drive.


Audio System


side of


Each time you press the the SEEK/SKIP bar, the system skips forward to the beginning of the next track. Press the side to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.


If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.


You can use the TUNE and SEEK/ SKIP bars while a disc is playing to select passages and change tracks.


To move rapidly within a track, press and hold the TUNE bar. Press the


side to move forward. You will


see CUE in the display. Press the side to move backward. You


will see REW displayed. Release the bar when the system reaches the point you want.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


REPEAT — To activate the Repeat feature, press and release the RPT button. You will see RPT in the display. The system continuously replays the current track. Press the RPT button again to turn it off.


RANDOM PLAY — This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press and release the A. SEL/RDM button. You will see RDM in the display. The system will then select and play tracks randomly. This continues until you deactivate Random Play by pressing A. SEL/RDM again.


If the system is in Repeat mode, you must turn it off by pressing the RPT button before selecting Random Play.


Comfort and Convenience Features


Main MenuTable of Contentsst Operating the CD Changer (Optional) A Compact Disc changer is available for your vehicle. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player.


Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Odd- shaped CDs may jam in the drive or cause other problems.


To select the CD changer, press the CD button. The disc and track numbers will be displayed.


Audio System


To select a different disc, press the appropriate preset button (1 — 6). If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot. This continues until it finds a CD to load and play.


When you switch back to CD mode, the system selects the same unit (in- dash or changer) that was playing when you switched out of CD mode.


To use the SKIP, REPEAT, and RANDOM functions, refer to the in- dash player operating instructions.


If you load a CD in the in-dash player while the changer is playing a CD, the system will stop the changer and begin playing the in-dash CD. To select the changer again, press the CD button. Play will begin where it left off. Use the CD button to switch between the player and the changer.


If you eject the in-dash CD while it is playing, the system will automatically switch to the CD changer and begin play where it left off. If there are no CDs in the changer, the display will flash. You will have to select another mode (AM or FM) with the button.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Protecting Compact Discs


When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat.


To clean a disc, use a clean soft cloth Wipe across the disc from the center to the outside edge.


Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Never try to insert foreign objects in the CD player or the magazine.


A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the re- cording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.


Comfort and Convenience Features


Main MenuTable of Contentsst CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the vehicle to your Honda dealer.


Audio System


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Remote Audio Controls


then release it.


in the audio system display.


AUDIO CONTROL BUTTON


CHANNEL BUTTON


MUTE BUTTON


VOLUME LEVER


If you want to mute the sound temporarily, push the MUTE button. The indicator in the button will light to indicate the mute function is on. Press the button again to cancel MUTE.


The AUDIO CONTROL button changes the mode. Pressing the button repeatedly selects AM, FM1, FM2, or CD (if a CD is loaded) two.


If you are playing a CD, the system skips to the beginning of the next track each time you push the CHANNEL button.


These controls work only with the factory-installed audio system. They will not function if you install any other system.


Four controls for the audio system are on the left side of the dashboard by the instrument panel. These let you control basic fund ions without distracting your attention from driving.


Use the VOLUME lever to adjust the volume. Push the lever up to increase the volume and down to decrease it. Hold the lever until the volume reaches the desired level,


The CHANNEL button has two functions, depending on whether you are listening to the radio, or playing a CD.


If you are listening to the radio, use the CHANNEL button to change stations. Each time you press this button, the system advances to the next preset station on the band you are listening to. You will see the number of the selected Preset button


Comfort and Convenience Features


Main MenuTable of Contentsst Theft Protection Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.


You should have received a card that lists your audio system's code number and serial number. It is best to store this card in a safe place at home. In addition, you should write the audio system's serial number in this Owner's Manual. If you should happen to lose the card, you must obtain the code number from your Honda dealer. To do this, you will need the system's serial number.


If your car's battery is disconnected or goes dead, or the radio fuse is removed, the audio system will disable itself. If this happens, you will see "Code" in the frequency display the next time you turn on the system. Use the Preset buttons to enter the five-digit code. If it is entered correctly, the radio will start playing.


If you make a mistake entering the code, do not start over or try to correct your mistake. Complete the five-digit sequence, then enter the correct code. You have ten tries to enter the correct code. If you are unsuccessful in ten attempts, you must then leave the system on for one hour before trying again.


Audio System


You will have to store your favorite stations in the Preset buttons after the system begins working. Your original settings were lost when power was disconnected.


Comfort and Convenience Features


Main MenuTable of Contentsst Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.


Before Driving


Break-in Period.............................. 116
Gasoline.......................................... 116
Service Station Procedures .......... 117
Filling the Fuel Tank................. 117
Opening the Hood..................... 118
Oil Check................................ 119
Engine Coolant Check.......... 120
Fuel Economy................................ 121
Car Condition............................. 121
Driving Habits............................ 121
Accessories and Modifications.... 122
Accessories................................. 122
Modifications............................. 123
Additional Safety Precaution.... 123
Carrying Cargo.............................. 124
General Precautions...................... 127


Before Driving


Main Menust Break-in Period, Gasoline


Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:


Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500 rpm for the first 600 miles (1,000 km) of operation.


Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300
km).


You should follow these same re- commendations with an overhauled or exchanged engine, or when the brakes are relined.


Before Driving


In Canada, some gasolines contain an octane-enhancing additive called MMT. If you use such gasolines, your emission control system performance may deteriorate and the Malfunction Indicator Lamp on your instrument panel may turn on. If this happens, contact your authorized Honda dealer for service


Gasoline Your Honda is designed to operate on premium unleaded gasoline with a pump octane number of 91 or higher.


If you are unable to find premium unleaded gasoline, you may substi- tute an unleaded regular gasoline. The engine will compensate for the lower octane, but you may notice a slight decrease in power as a result.


We recommend gasolines containing detergent additives that help prevent fuel system and engine deposits.


Using gasoline containing lead will damage your car's emissions controls. This contributes to air pollution.


Main MenuTable of Contentsst Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.


Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately.


Filling the Fuel Tank


1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps.


2. Open the fuel fill door by pulling on the knob on the driver's door jamb.


Service Station Procedures


FUEL FILL CAP


3. Remove the fuel fill cap slowly.


You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door.


CONTINUED


Before Driving


Main MenuTable of Contentsst Service Station Procedures


4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to "lop off" the tank, leave some room for the fuel to expand with temperature changes.


5. Screw the fuel fill cap back on, tighten it until it clicks at least three times. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 228).


6. Push the fuel fill door closed until


it latches.


Before Driving


Opening the Hood


RELEASE HANDLE


1. Shift to Neutral and set the


parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.


2. Standing in front of the car, put


your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle. Push this handle to the left until it


releases the hood. Lift the hood.


If you can open the hood without lifting the hood latch handle, or the hood latch handle moves stiffly or does not spring back as before, the mechanism should be cleaned and lubricated (see page 174).


Main MenuTable of Contentsst Service Station Procedures


Oil Check


DIPSTICK


3. Pull the support rod out of its clip


and insert the end into the hole on the front of the hood around the center. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. After closing the hood, make sure it is securely latched.


Check the engine oil level every time you fill the car with fuel. Wait a few minutes after turning the engine off before you check the oil.


1. Remove the dipstick (black


handle).


2. Wipe the dipstick with a clean


cloth or paper towel.


CONTINUED


Before Driving


Main MenuTable of Contentsst Service Station Procedures


Engine Coolant Check


UPPER MARK


LOWER MARK


4. Remove the dipstick again and


check the level. It should be between the upper and lower marks.


If it is near or below the lower mark, see Adding Oil on page 157.


Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 161 for information on adding the proper coolant.


Refer to Owner Maintenance Checks on page 155 for information on checking other items in your Honda.


3. Insert it all the way back in its tube.


Before Driving


Main MenuTable of Contentsst The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get.


Car Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition.


An important part of that mainte- nance is the Owner Maintenance Checks (see page 155 ). For example, an underinflated tire causes more "rolling resistance," which uses fuel. It also wears out faster, so check the tire pressure at least monthly.


In winter, the build-up of snow on your car's underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion.


Driving Habits You can improve fuel economy by driving moderately. Rapid acceler- ation, abrupt cornering, and hard braking use more fuel.


Always drive in the highest gear that allows the engine to run and acceler- ate smoothly.


Depending on traffic conditions, try to maintain a constant speed. Every time you slow down and speed up, your car uses extra fuel. Use the cruise control, when appropriate, to increase fuel economy.


A cold engine uses more fuel than a warm engine. It is not necessary to "warm-up" a cold engine by letting it idle for a long time. You can drive away in about a minute, no matter how cold it is outside. The engine will warm up faster, and you get better fuel economy. To cut down on the number of "cold starts," try to


Fuel Economy


combine several short trips into one.


The air conditioning puts an extra load on the engine which makes it use more fuel. Turn off the A/C to cut down on air conditioning use. Use the flow-through ventilation when the outside air temperature is moderate.


Before Driving


Main MenuTable of Contentsst Accessories and Modifications


Modifying your car, or installing some non-Honda accessories, can make your car unsafe. Before you make any modifications or add any accessories, be sure to read the following information.


Accessories Your dealer has Genuine Honda accessories that allow you to personalize your car. These accessories have been designed and approved for your car, and are covered by warranty.


Non-Honda accessories are usually designed for universal applications. Although aftermarket accessories may fit on your car, they may not meet factory specifications, and could adversely affect your car's handling and stability. (See "Modifications" on the page 123 for additional information.)


Before Driving


Improper accessories or modifications can affect your car's handling, stability and performance, and cause a crash in which you can be hurt or killed.


Follow all instructions in this owner's manual regarding accessories and modifications.


When properly installed, cellular phones, alarms, two-way radios, and low-powered audio systems should not interfere with your car's computer-controlled systems, such as the SRS and anti-lock brake system.


However, if electronic accessories are improperly installed, or exceed your car's electrical system capacity, they can interfere with the operation of your car, or even cause the airbags to deploy.


Before installing any accessory:


Make sure the accessory does not obscure any lights, or interfere with proper car operation or performance.


Be sure electronic accessories do not overload electrical circuits (see page 231).


Have the installer contact your Honda dealer for assistance before installing any electronic accessory.


If possible, have your dealer inspect the final installation.


Main MenuTable of Contentsst Accessories and Modifications


Modifications Do not remove any original equipment or modify your car in any way that would alter its design or operation. This could make your car unsafe and illegal to drive.


In addition, any modifications that decrease ground clearance increase the chance of undercarriage parts striking a curb, speed bump, or other raised object, which could cause your airbags to deploy.


For example, do not make any modifications that would change the ride height of your car, or install wheels and tires with a different overall diameter.


Do not modify your steering wheel or any other part of your Supplemental Restraint System. Modifications could make the system ineffective.


Additional Safety Precaution Do not attach or place objects on the airbag covers. Any object attached to or placed on the covers marked "SRS AIRBAG," in the center of the steering wheel and on top of the dashboard, could interfere with the proper operation of the airbags. Or, if the airbags inflate, the objects could be propelled inside the car and hurt someone.


Such modifications can adversely affect handling, and interfere with the operation of the car's anti-lock brakes and other systems.


Before Driving


Main MenuTable of Contentsst Carrying Cargo


UPPER AND LOWER CONSOLE COMPARTMENTS


TRUNK


Before Driving


Your car has several convenient storage areas so yon can stow cargo safely.


The upper and lower console compartments are designed for small, lightweight items. The trunk is intended for larger, heavier items.


However, carrying too much cargo, or improperly storing it, can affect your car's handling, stability and operation and make it unsafe. Before carrying any type of cargo, be sure to read the following pages.


Main MenuTable of Contentsst Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed.


Follow all load limits and other loading guidelines in this manual.


Carrying Cargo


Carrying Items in the Passenger Compartment


Store or secure all items that could be thrown around and hurt someone during a crash.


Be sure items placed on the floor behind the front scats cannot roll under the seats and interfere with the driver's ability to operate the pedals, or with the proper operation of the seats.


Load Limit The maximum load for your car is 400 Ibs (185 kg).


This figure includes the total weight of all occupants, cargo, and accessories.


To figure out how much cargo you can carry:


Add up the weight of all occupants.


Subtract the total from 400 Ib (185
kg).


The final number is the total weight of cargo you can cany.


Before Driving


Main MenuTable of Contentsst Carrying Cargo


Carrying Cargo in the Trunk


Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.


Before Driving


Main MenuTable of Contentsst Your Honda is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your car has a minimum of ground clearance and very low- profile tires.


Use caution if you should drive your car on very rough or rutted roads. You could damage the suspension and underbody by bottoming out. Going too fast over parking lot "speed bumps" can also cause damage.


Curbs and steep inclines could damage the front and rear bumpers. Low curbs that do not affect the average car may be high enough to hit the bumper on your Honda. The front or rear bumper may scrape when trying to drive onto an incline, such as a steep driveway or trailer ramps.


General Precautions


Because of the low-profile tires fitted to your car, the alloy wheels are closer to the ground. Driving over a pothole or road debris at too high a speed can seriously damage a wheel. Slow down under these conditions.


Before Driving


Main MenuTable of Contentsst This section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your car, and the braking system.


Driving


Preparing to Drive......................... 130
Starting the Engine........................ 131


Starting in Cold Weather


at High Altitude..................... 132
6-speed Manual Transmission..... 133
Recommended Shift Points...... 134
Engine Speed Limiter............... 134
Reverse Lockout........................ 134
Parking............................................ 135
The Braking System...................... 136
Brake Wear Indicators.............. 136
Brake System Design................ 137
Anti-lock Brakes........................ 137


Important Safety


Reminders.......................... 138
ABS Indicator......................... 139
Driving in Bad Weather................ 140
Towing a Trailer............................ 141


Driving


Main Menust Preparing to Drive


You should do the following checks and adjustments every day before you drive your car.


1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.


2. Check that the hood and trunk are


fully closed.


3. Visually check the tires. If a tire


looks low, use a gauge to check its pressure.


4. Check that any items you may be


carrying with you inside are stored properly or fastened down securely.


5. Check the adjustment of the seat


(see page 68).


6. Check the adjustment of the


inside and outside mirrors (see page 79).


7. Make sure the doors are securely


closed and locked.


8. Fasten your seat belt. Check that your passenger has fastened his seat belt (see page 15).


9. Turn the ignition switch ON (II). Check the indicator lights in the instrument panel.


10. Start the engine (see page 131).


11. Check the gauges and indicator


lights in the instrument panel (see page 4 3).


Driving


Main MenuTable of Contentsst 1. Apply the parking brake.


2. In cold weather, turn off all


electrical accessories to reduce the drain on the battery.


3. Push the clutch pedal down all the way. The ENGINE START button has no effect unless the clutch pedal is depressed.


4. Turn the ignition key to ON (II)


position.


ENGINE START BUTTON


5. Without touching the accelerator pedal, push the ENGINE START button. If the engine does not start right away, do not hold the ENGINE START button for more than 15 seconds at a time. Pause for at least 10 seconds before trying again.


Starting the Engine


6. If the engine does not start within


15 seconds, or starts but stalls right away, repeat step 5 with the accelerator pedal pressed half-way down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.


7. If the engine still does not start,


press the accelerator pedal all the way down and hold it there while starting in order to clear flooding. As before, hold the ENGINE START button for no more than 15 seconds. Return to step 6 if the engine does not start. If it starts, lift your foot off the accelerator pedal so the engine does not race.


Driving


Main MenuTable of Contentsst Starting the Engine


Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400
meters) adds to the problem.


Use the following procedure:


1. Turn off all electrical accessories


to reduce the drain on the battery.


2. Push the accelerator pedal half- way to the floor and hold it there while starting the engine. Do not hold the ENGINE START button for more than 15 seconds. When the engine starts, release the accelerator pedal gradually as the engine speeds up and smooths out.


3. If the engine fails to start in step 2,


push the accelerator pedal to the floor and hold it there while you try to start the engine for no more than 15 seconds. If the engine does not start, return to step 2.


Driving


Main MenuTable of Contentsst 6-speed Manual Transmission


Rapid slowing or speeding-up can cause loss of control on slippery surfaces. If you crash, you can be injured.


Use extra care when driving on slippery surfaces.


Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind."


When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure engine speed will not go into the tachometer's red zone in the lower gear.


Driving


The manual transmission is synchro- nized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from Fifth to Reverse instead of sixth (see page 134). When shifting up or down, make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.


Main MenuTable of Contentsst 6-speed Manual Transmission


Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emis- sions control. The following shift points are recommended:


Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the RPM below the red zone.


Before downshifting, make sure the engine will not go into the tachometer's red zone in the lower gear.


Reverse Lockout


The 6-speed manual transmission has a lockout so you cannot accidentally shift from Fifth to Reverse instead of Sixth.


With the clutch pedal depressed, move the shift lever to the Reverse side of the Neutral gate, then push the shift lever down and shift to Reverse.


Driving


Main MenuTable of Contentsst Always use the parking brake when you park your car. The indicator on the instrument panel shows that the parking brake is not fully released; it does not indicate that the parking brake is firmly set. Make sure the parking brake is set firmly or your car may roll if it is parked on an incline.


If the car is facing uphill, turn the front wheels away from the curb and put the transmission in first gear. If the car is facing downhill, turn the front wheels toward the curb and put the transmission in reverse gear.


Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.


Parking


Loading...
x