Download PDF Manual

allows you to tilt the steering wheel.


MOONROOF (P. 87)


HEADLIGHTS/ TURN SIGNALS (P. 62)


TILT ADJUSTMENT (P. 66)


HORN BUTTONS


REAR WINDOW DEFOGGER (P. 65)


Instruments and Controls


Main MenuTable of Contentsst Controls Near the Steering Wheel


Headlights


If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder chime when you open the driver's door.


position turns


The rotating switch on the left lever controls the lights. Turning this switch to the on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights.


Instruments and Controls


To change between low beams and high beams, pull the turn signal lever until you hear a click, then let go. The blue high beam indicator will light (see page 57).


To flash the high beams, pull the turn signal lever back lightly, then release it. The high beams will come on and go off.


The high beams will stay on for as long as you hold the lever back, no matter what position the headlight switch is in.


Daytime Running Lights (Canadian Models) With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake.


The headlights revert to normal operation when you turn them on with the switch.


Main MenuTable of Contentsst Instrument Panel Brightness


Turn Signals


Controls Near the Steering Wheel


To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it.


The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness.


TURN SIGNAL LEVER


Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn.


Instruments and Controls


Main MenuTable of Contentsst Controls Near the Steering Wheel


Windshield Wipers


The right lever controls the wind- shield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent


: low speed : high speed


In intermittent, the wipers operate every few seconds. You can vary how often the wipers sweep the windshield by turning the INT TIME ring next to the rotary switch. In low speed and high speed, the wipers run continuously.


To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield.


Instruments and Controls


Main MenuTable of Contentsst Windshield Washers


Hazard Warning


Rear Window Defogger


Controls Near the Steering Wheel


To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.


The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it.


Push the red button to the left of the clock to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your car is disabled.


The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 25 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the car.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Controls Near the Steering Wheel


Make sure the rear window is clear and you have good visibility before starting to drive.


The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.


Instruments and Controls


Steering Wheel Adjustment See page 17 for important safety information about how to properly position the steering wheel. Make any steering wheel adjustment before you start driving.


Adjusting the steering wheel position while driving may cause you to lose control of the car and be seriously injured in a crash.


Adjust the steering wheel only when the car is stopped.


To adjust the steering wheel upward or downward:


1. Push the lever under the steering


column all the way down.


2. Move the steering wheel to the


desired position, making sure the wheel points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and the indicator lights.


3. Push the lever up to lock the


steering wheel in that position.


4. Make sure you have securely


locked the steering wheel in place by trying to move it up and down.


Main MenuTable of Contentsst Cruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.


Improper use of the cruise control can lead to a crash.


Use the cruise control only when traveling on open highways in good weather.


Steering Wheel Controls


NOTICE


Using the Cruise Control


The cruise control, as it operates, moves the accelerator pedal. You can damage your car's accelerator mechanism by resting your foot under the pedal and blocking the movement.


CRUISE CONTROL MASTER SWITCH


1. Push in the Cruise Control Master


Switch to the left of the steering column. The indicator in the switch will light.


2. Accelerate to the desired cruising


speed above 25 mph (40 km/h).


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Steering Wheel Controls


RESUME/ accel


SET/decel


3. Press and release the SET/decel button on the steering wheel. The CRUISE CONTROL light on the instrument panel comes on to show the system is now activated.


The cruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down to the desired speed. This will cancel the


Instruments and Controls


cruise control. To resume the set speed, press the RESUME/accel button. The CRUISE CONTROL light on the instrument panel comes on. When climbing a steep hill, the automatic transmission may downshift to hold the set speed.


Changing the Set Speed You can increase the set cruising speed in any of these ways:


Press and hold the RESUME/ accel button. The car will acceler- ate. When you reach the desired cruising speed, release the button.


Push on the accelerator pedal. Ac- celerate to the desired cruising speed and press the SET/decel button.


To increase your speed in very small amounts, tap the RESUME/ accel button repeatedly. Each time


you do this, your vehicle will speed up about 1 mph (1.6 km/h).


You can decrease the set cruising speed in any of these ways:


Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed.


To slow down in very small amounts, tap the SET/decel button repeatedly. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).


Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out. When the car slows to the desired speed, press the SET/decel button. The car will then maintain the desired speed.


Main MenuTable of Contentsst Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed.


Resting your foot on the brake or clutch pedal will cause the cruise control to cancel.


Cancelling the Cruise Control You can cancel the cruise control in any of these ways:


Tap the brake or clutch pedal.


Press the SET/decel and RE- SUME/accel buttons at the same time.


Press the Cruise Control Master Switch.


When you tap the brake or clutch pedal, or press the SET and RE- SUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way.


The system remembers the previously-set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h) and press


Steering Wheel Controls


the RESUME/accel button until the CRUISE CONTROL light comes on. The car will accelerate to the same cruising speed as before.


Pressing the Cruise Control Master Switch turns the system completely off and erases the previous cruising speed from memory. To use the system again, refer to Using the Cruise Control.


Instruments and Controls


Main MenuTable of Contentsst Keys and Locks


Keys


MASTER KEYS (Black)


VALET KEY (Gray)


KEY NUMBER PLATE


Your car comes with two master keys and a valet key. The master key fits all the locks on your vehicle:


Ignition Doors Trunk Trunk release handle Rear seat trunk access Glove box


Instruments and Controls


The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle, rear seat trunk access and the glove box locked when you leave your car and the valet key at a parking facility.


You should have received a key number plate with your keys. You will need this key number if you ever have to get a lost key replaced. Keep the plate stored in a safe place. If you


need to replace a key, use only Honda-approved key blanks.


These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged.


Protect the keys from direct sunlight, high temperature, and high humidity.


Do not drop the keys or set heavy objects on them.


Keep the keys away from liquids. If they get wet, dry them immedi- ately with a soft cloth.


The keys do not contain batteries. Do not try to take them apart.


Main MenuTable of Contentsst If you attempt to use the learning key to start your car's engine, it may cause a malfunction in the system that makes your master and valet keys unusable. If this happens, you should contact your Honda dealer.


If you need a new key made, take the key number plate, the learning key, and all other keys that came with your car to your Honda dealer.


Remote Transmitter Your car also comes with two remote transmitters; see page 75 for an explanation of the operation.


Learning Key


You should also receive a small case containing a learning key. It is used by the Honda dealer to code replace- ment keys to your car's Immobilizer System. It must not be used in your car's ignition switch. Store the learn- ing key with the key number plate in a safe place.


Keys and Locks


Immobilizer System The Immobilizer System protects your car from theft. A properly- coded ignition key must be used in the ignition switch for the engine to start. If an improperly-coded key (or other device) is used, the engine's fuel system is disabled.


When you turn the ignition switch to ON (II). the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Keys and Locks


This indicator will also blink several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).


The system may not recognize your key's coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code:


Do not keep other immobilizer keys on the same key ring.


Use a plastic or leather key fob, not metal.


Keep other keys away from your vehicle's key and the ignition switch while trying to start the engine.


Instruments and Controls


If the system repeatedly does not recognize the coding of your key, contact your Honda dealer.


Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your car undriveable.


If you have lost your key and you cannot start the engine, contact your Honda dealer.


As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device way not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


This device complies with Industry Canada Standard RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference that may cause undesired operation of the device.


Main MenuTable of Contentsst LOCK (0) — You can insert or remove the key only in this position. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic transmission, the shift lever must also be in Park. The anti- theft lock will lock the steering column when you remove the key. If the front wheels are turned, the anti-theft lock may sometimes make it difficult to turn the key from LOCK to ACCESSORY. Firmly turn the steering wheel to the left or to the right as you turn the key.


Ignition Switch


The ignition switch is on the right side of the steering column. It has four positions:


LOCK (0) ACCESSORY (I) ON (II) START (III)


Keys and Locks


Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control.


Remove the key from the ignition switch only when parked.


ACCESSORY (I) — In this position, you can operate the audio system and the accessory power socket.


ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instru- ment panel come on as a test when you turn the ignition switch from ACCESSORY to ON.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Keys and Locks


START (III) — Use this position only to start the engine. The switch returns to ON (II) when you let go of the key.


The engine will not start if the Immobilizer System does not recognize the key's coding (see page 71).


You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper.


Instruments and Controls


Power Door Locks


Each door has a master door lock switch. This switch locks and unlocks both doors. Push the switch down to lock both doors and up to unlock them.


Each door has a lock tab next to the inside door handle. When you push in the lock tab on the driver's door, both doors lock. Pulling out the lock tab on the driver's door only unlocks that door. The lock tab on the passenger's door only locks and unlocks that door.


Main MenuTable of Contentsst To lock the passenger's door when getting out of the car, push the lock tab in and close the door. To lock the driver's door, remove the key from the ignition switch and push the lock tab in or push the master switch down, then close the door.


Both doors can be locked from the outside by using the key in either door.


To unlock only the driver's door from the outside, insert the key in the driver's door lock, turn the key and release it. If you turn the key and hold it, both doors will unlock. Both doors will unlock when you unlock the passenger's door with the key.


Lockout Prevention If you forget and leave the key in the ignition switch, Lockout Prevention will not allow you to lock the driver's door. With the driver's door open and the key in the ignition, both master door lock switches are disabled. However, if the driver's door is not open, the master door lock switches are not disabled. Pushing the switch down on the open passenger's door will lock both doors. If you try to lock an open driver's door by pushing in the lock tab, the tabs on both doors pop out. Pushing in the lock tab on the passenger's door only locks that door.


Keys and Locks


Remote Transmitter


LED


LOCK BUTTON


UNLOCK BUTTON


You can lock and unlock your car with the remote transmitter. When you push the LOCK button, both doors lock.


When you push the UNLOCK button once, only the driver's door unlocks. The passenger's door unlocks when you push the button a second time.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Keys and Locks


The ceiling light (if the ceiling light switch is in the center position) will come on when you press the UNLOCK button. If you do not open either door, the light will go out in about 10 seconds and the doors will automatically relock. If you relock the doors with the remote transmitter before 10 seconds have elapsed, the light will go off immediately.


You cannot lock or unlock the doors with the remote transmitter if either door is not fully closed or the key is in the ignition switch.


Instruments and Controls


Replacing the Battery


ROUND COVER


CUSHION RING


Open


Close


BATTERY


When the remote transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will get dim. Replace the battery as soon as possible.


Battery type: CR2025


To replace the battery, remove the round cover on the back of the trans- mitter by turning it counterclockwise with a coin.


Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same (+ side facing up), then insert it in the transmitter.


Main MenuTable of Contentsst Reinstall the cushion ring. Align the mark on the cover with the mark on the transmitter,


then set the cover in place and turn it clockwise.


Transmitter Care Avoid severe shock to the trans- mitter, such as dropping or throwing it. Also, protect it from extreme hot or cold temperatures.


Clean the transmitter case with a soft cloth. Do not use strong cleaners or solvents that could harm the case. Immersing the transmitter in any liquid will harm the trans- mitter and cause it to not function properly.


If you lose a transmitter, you will need to have the replacement programmed to your car's system by your Honda dealer. Any other transmitters you have will also need to be reprogrammed.


Keys and Locks


As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


This device complies with Industry Canada Standard RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference that may cause undesired operation of the device.


Instruments and Controls


Main MenuTable of Contentsst Keys and Locks


Trunk


MASTER KEY


TRUNK RELEASE HANDLE


You can open the trunk in two ways:


Pull the trunk release handle to the left of the driver's seat.


Use the master key to open the trunk lock. The valet key does not work in this lock.


To close the trunk, press down on the trunk lid.


See page 136 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 49 .


MASTER KEY


To protect items in the trunk when you need to give the key to someone else, lock the trunk release handle with the master key and give the other person the valet key.


Instruments and Controls


Main MenuTable of Contentsst Glove Box


An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.


Always keep the glove box closed while driving.


Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key.


Keys and Locks


Instruments and Controls


Main MenuTable of Contentsst Seat Adjustments


Front Seat Adjustments See pages 13 — 14 for important safety information and warnings about how to properly position seats and seat-backs.


Instruments and Controls


Adjust the seat before you start driving.


To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.


To change the angle of the seat-back, pull up on the lever on the outside of the seat bottom. Move the seat-back to the desired position and release the lever. Let the seat-back latch in the new position.


Main MenuTable of Contentsst Driver's Seat Height Adjustment


Rear Seat Access To get into the back seat on the driver's side, pull up on the seat-back adjustment lever.


RELEASE LEVER


Seat Adjustments


See pages 13 — 14 for important safety information and warnings about how to properly position seats and seat-backs. To adjust the height of the driver's seat, turn the dial on the outside of the seat bottom.


To get into the back seat on the passenger's side, push forward on the release lever at the base of the seat-back. The seat-back will tilt forward and the entire seat will move forward to allow easier entry to the back seat. After you return the seat- back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before sitting in it.


Instruments and Controls


Main MenuTable of Contentsst Seat Adjustments


Head Restraints See page 15 for important safety information and a warning about how to properly position the head restraints.


Instruments and Controls


The front head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.


To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button and pull the restraint out of the seat- back.


RELEASE BUTTON


The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the back of the occupant's head rests against the center of the restraint. A taller person should adjust the restraint as high as possible.


Main MenuTable of Contentsst Seat Heaters


Follow these precautions whenever you use the seat heaters:


Use the HI setting only to heat the seats quickly. Select the LO setting when the seats feel warm. The HI setting draws large amounts of current from the battery.


Do not use the seat heaters, even on the LO setting, if the engine is left idling for an extended period. They can weaken the battery, causing hard starting.


The HI or LO indicator lights and remains lit until you turn it off by pushing the opposite side of the switch lightly. The indicator will turn off.


In HI, the heater turns off when the seat gets warm, and turns back on after the seat's temperature drops. It continues to cycle as long as you leave it set on HI. The HI indicator remains lit as a reminder that you have the heater on.


In LO, the heater runs continuously. It does not cycle with temperature changes.


SEAT HEATER


On Canadian models Both front seats are equipped with seat heaters. The ignition switch must be ON (II) to use them. Push the front of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the back of the switch. This will keep the seat warm.


Instruments and Controls


Main MenuTable of Contentsst Folding Rear Seat


The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the car or inside the trunk.


MASTER KEY


RELEASE


To fold down the seat-back from inside the car. insert the master key in the lock on the rear shelf. Turn the key clockwise, pull down the top of the seat-back, then release the key.


Pull


To release the seat-back from inside the trunk, pull the release under the rear shelf.


To lock the seat-back upright, push it firmly against the rear shelf. Make sure it is latched in place by pulling on the top of the seat.


Instruments and Controls


Main MenuTable of Contentsst Folding Rear Seat, Power Windows


Make sure both rear shoulder belts are positioned in front of the rear seat-back whenever the seat-back is in its upright position.


Power Windows Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window.


Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See Carrying Cargo on page 135.


Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.


Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 49.


DRIVER'S WINDOW SWITCH


MAIN SWITCH


The driver's armrest has a master power window control panel. To open the passenger's window, push down on the switch and hold it down until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Power Windows


Closing a power window on someone's hands or fingers can cause serious injury.


Make sure your passengers are away from the windows before closing them.


Instruments and Controls


The master control panel also con- tains these extra features:


AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly.


To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.


The AUTO function only works to lower the driver's window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position.


The MAIN switch controls power to the passenger's window. With this switch off, the passenger's window cannot be raised or lowered. The MAIN switch does not affect the driver's window. Keep the MAIN switch off when you have children in the car so they do not injure them- selves by operating the window unintentionally.


The power window system has a key- off delay function. The windows will still operate for up to ten minutes after you turn off the ignition. Opening either door cancels the delay function. You must turn the ignition ON (II) again before you can raise or lower the windows.


Main MenuTable of Contentsst Moonroof


The moonroof has a key-off delay. You can still open and close the moonroof for up to ten minutes after you turn off the ignition. The key-off delay cancels as soon as you open either door. You must then turn the ignition ON (II) for the moonroof to operate.


NOTICE


If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.


Closing the moonroof on someone's hands or fingers can cause serious injury.


Make sure passengers are clear of the moonroof before closing it.


Instruments and Controls


MOONROOF SWITCH


Use the switch on the dashboard to open and close the moonroof. The ignition switch must be ON (II). Push and hold the open the moonroof. Release the switch when the moonroof reaches the desired position. To close the moonroof, press and hold the


switch to


switch.


Main MenuTable of Contentsst Mirrors


Adjusting the Power Mirrors


SELECTOR SWITCH


TAB


Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.


The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.


Instruments and Controls


Adjust the outside mirrors with the adjustment switch on the driver's door armrest:


3. Push the appropriate edge of the


adjustment switch to move the mirror right, left, up or down.


1. Turn the ignition switch ON (II).


2. Move the selector switch to L


(driver's side) or R (passenger's side).


4. When you finish, move the


selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch.


Main MenuTable of Contentsst Mirrors, Parking Brake


Parking Brake


NOTICE


HEATED MIRROR BUTTON


PARKING BRAKE LEVER


Driving the car with the parking brake applied can damage the rear brakes and axles.


Available on all Canadian models The outside mirrors are heated to re- move fog and frost. With the ignition switch ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off.


To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 55).


Instruments and Controls


Main MenuTable of Contentsst You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET button sets the clock back to the previous hour. If the displayed time is after the half hour, pressing the RESET button sets the clock for- ward to the beginning of the next hour. For example:


1:06 would RESET to 1:00. 1:52 would RESET to 2:00.


Digital Clock


HOUR M IN RESET


To set the clock:


1. Turn the ignition switch ON (II) to


display the time.


2. Swing down the front cover of the


wide button under the clock display. You will see HOUR, MIN, and RESET buttons.


3. Press and hold the HOUR button


until the hour advances to the desired hour.


4. Press and hold the MIN (minute) button until the numbers advance to the desired minutes.


The digital clock displays the time with the ignition switch ON (II).


Instruments and Controls


Main MenuTable of Contentsst PARTITION


The front beverage holder is located on the center console. The partition in the beverage holder can be moved forward or backward. If you want to use the beverage holder, slide the partition forward until it clicks. To put small items in the beverage holder, slide the partition completely backward.


Beverage Holder


Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Beverage Holder, Console Compartment


Console Compartment


LEVER


LEVER


The rear seat also has a beverage holder in the armrest on the driver's side.


CONSOLE COMPART- MENT


To open the console compartment, pull up on the lower lever and lift the lid.


To close, lower the lid and push it down until it latches.


You can put small items in the tray located in the console compartment lid. To use the tray, pull up on the upper lever and lift up the armrest pad.


Instruments and Controls


Main MenuTable of Contentsst Coin Box


Accessory Power Socket


Coin Box, Accessory Power Socket


The coin box is located next to the beverage holder. Open the lid by lifting it up.


To remove the coin box for emptying, lift the coin box up by pushing up on the middle edge of the coin box on the console guide. Never use the coin box for smoking materials.


ACCESSORY POWER SOCKET


To use the accessory power socket, pull down the cover. The ignition switch must be in ACCESSORY (I) or ON (II).


This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).


It will not power an automotive type cigarette lighter element.


Instruments and Controls


Main MenuTable of Contentsst Ashtrays, Interior Lights


Ashtrays (Optional) A front ashtray, which is available as an option, can be used as a replacement for the coin box.


NOTICE


Use the ashtray only for cigarettes, cigars, and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray.


Ceiling Lights


DOOR ACTIVATED


OFF


ON


The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open either door. After both doors are closed tightly, the light dims slightly, then fades out in about 10 seconds. In the ON position, the ceiling light stays on continuously.


The ceiling light contains a main light as well as two spotlights.


Instruments and Controls


Main MenuTable of Contentsst Courtesy Lights


Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. You can use the spotlights at all times.


Your car has a courtesy light in the ignition switch. The ignition switch light comes on whenever you open either door. It remains on, then fades out in about 10 seconds after both doors are closed tightly.


The ignition switch light and ceiling light (with the switch in the center position) also comes on when you unlock the door with the key, the lock tab on the driver's door, or the


Interior Lights


master door lock switch. If you relock the driver's door or close the driver's door with the key in the ignition switch, the lights turns off immediately. Otherwise, the light remains on, then fades out in about 10 seconds.


If you keep the door open, the ceiling light (with the switch in the center position) will turn off after three minutes when the key is not in the ignition switch.


On Type SH Your car also has a courtesy light in each door. Each door light comes on when the door is opened, and goes out when the door is closed tightly.


Instruments and Controls


Main MenuTable of Contentsst Comfort and Convenience Features


The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions.


The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.)


Your Honda has an anti-theft audio system that requires a code number to enable it.


Heating and Cooling........................ 98
What Each Control Does............ 98
How to Use the System............. 100
To Turn Everything Off ........... 105
Audio System................................. 106
AM/FM/CD Audio System..... 106
Operating the Radio.................. 106
Adjusting the Sound.................. 109
Audio System Lighting............. 110
Radio Frequencies..................... 110
Radio Reception......................... 110
Operating the CD Player.......... 112
Operating the CD Changer...... 114
Protecting Compact Discs........ 116
CD Player Error Indications..... 117
CD Changer Error


Indications.............................. 118


Operating the Cassette


Player...................................... 119
Tape Search Functions............. 120
Caring for the Cassette


Player...................................... 122
Theft Protection ........................ 123


Comfort and Convenience Features


Main Menust Heating and Cooling


Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility.


What Each Control Does


Fan Control Lever Sliding this lever to the right increases the fan's speed, which increases air flow.


Temperature Control Lever Sliding this lever to the right increases the temperature of the air flow.


Air Conditioning (A/C) Button This button turns the air condi- tioning ON and OFF. The indicator in the button lights when the A/C is on.


Comfort and Convenience Features


MODE BUTTONS


REAR WINDOW DEFOGGER BUTTON


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Rear Window Defogger Button This button turns the rear window defogger on and off (see page 65).


Recirculation Button This button controls the source of the air going into the system. When the indicator in this button is lit, air from the car's interior is sent through the system again (Recircula- tion mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode).


Main MenuTable of Contentsst Mode Buttons Use the MODE buttons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.


Air flows from the center


and corner vents in the dashboard.


Air flow is divided between the vents in the dashboard and the floor vents.


Air flows from the floor


vents.


Air flow is divided between


the floor vents and the defroster vents at the base of the windshield.


Air flows from the defroster vents at the base of the windshield.


When you select automatically switches to Fresh Air mode and turns on the A/C.


, the system


Heating and Cooling


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


Vent Controls


CENTER VENT


SIDE VENT


Open


Close


You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-to- side.


The vents in the corners of the dashboard can be opened and closed with the dials underneath them.


Comfort and Convenience Features


How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting.


The engine must be running for the heater and air conditioning to generate hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.


Main MenuTable of Contentsst It is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears.


The outside air intakes for the heating and cooling system are at the base of the windshield. Keep these clear of leaves and other debris.


Heating and Cooling


MODE BUTTONS


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear window.


1. Slide the temperature control lever


all the way to the left. Make sure the A/C is off.


2. Select 3. Set the fan to the desired speed.


and Fresh Air mode.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


To Cool with A/C 1. Turn on the A/C by pressing the


button. The light in the button should come on when a fan speed is selected.


2. Make sure the temperature


control lever is set to maximum cool.


3. Select 4. If the outside air is humid, select


Recirculation mode. If the outside air is dry, select Fresh Air mode. 5. Set the fan to the desired speed.


Comfort and Convenience Features


MODE BUTTONS


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Main MenuTable of Contentsst If the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way:


1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the tempera- ture control lever is all the way to the left.


3. Set the fan to maximum speed. 4. Open the windows partially. Select


and Fresh Air mode.


When the interior has cooled down to a more comfortable temperature, close the windows and set the controls as described for normal cooling.


Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 59 ) when driving in stop-and-go traffic or climbing a long, steep hill. If it moves near the red zone, turn off the A/C until the gauge reads normally.


To Heat To warm the interior:


1. Start the engine. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with


and Fresh Air mode.


the temperature control lever.


Heating and Cooling


To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.


1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control


and Fresh Air mode.


lever so the mixture of heated and cooled air feels comfortable.


This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


To Defog and Defrost To remove fog from the inside of the windows:


1. Switch the fan on. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


MODE BUTTONS


REAR WINDOW DEFOGGER BUTTON


RECIRCULATION BUTTON


3. Adjust the temperature control


lever so the air flow from the defroster vents feels warm.


4. Turn on the rear window defogger


to help clear the rear window.


When you switch to another mode from Press the A/C button to turn if off.


the A/C stays on.


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Comfort and Convenience Features


Main MenuTable of Contentsst To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather:


1. Start the engine. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


3. Switch the fan and temperature


controls to maximum.


To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows.


Heating and Cooling


To Turn Everything Off To shut off the system temporarily, slide the fan speed and temperature control levers all the way to the left.


You should shut the system completely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior.


These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial underneath each vent. This will send more warm air to the windshield defroster vents.


For safety, make sure you have a clear view through all the windows before driving away.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


AM/FM/CD Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The anti-theft feature will disable the system if it is disconnected from the vehicle's battery. To get the system working again, you must enter a code number (see page 123 ).


Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.


Comfort and Convenience Features


STEREO INDICATOR


PWR/VOL KNOB


TUNE BAR


AM/FM BUTTON


SEEK BAR


PRESET BUTTONS


SCAN BUTTON


Main MenuTable of Contentsst You can use any of four methods to find radio stations on the selected band: TUNE, SEEK, SCAN or the Preset buttons.


TUNE — Use the TUNE bar to tune the radio to a desired frequency. Press the to a higher frequency, and the


side of the bar to tune


side to tune to a lower


frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly.


SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press the SEEK bar on either the or


side, then release it.


Depending on which side you press, the system scans upward or down- ward from the current frequency. It stops when it finds a station with a


Audio System


strong signal.


To store a frequency:


SCAN — The SCAN function samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. When the system is in the SCAN mode, SCAN shows in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds. When it plays a station that you want to continue listening to, press the SCAN button again.


Preset — You can store the frequencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two frequencies on the FM band.


1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button.


2. Use the TUNE or SEEK function


to tune the radio to a desired station.


3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep.


4. Repeat steps 1 to 3 to store a total


of six stations on AM and twelve on FM.


Once a station's frequency is stored, simply press and release the proper preset button to tune to it. The preset frequencies will be lost if your car's battery goes dead, is disconnected, or the radio fuse is removed.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area.


To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals; It stores the frequencies of six AM stations and twelve FM stations in the preset buttons. You can then use the preset buttons to select those stations.


If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a "0" displayed when you press any preset button that does not have a station stored.


Comfort and Convenience Features


AUTO SELECT INDICATOR


TUNE BAR


SEEK BAR


If you do not like the stations Auto Select has stored, you can store other frequencies in the preset buttons. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset buttons as described previously.


SCAN BUTTON A. SEL BUTTON


Auto Select does not erase the frequencies that you preset pre- viously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset buttons will then select the frequencies you originally set.


Main MenuTable of Contentsst Adjusting the Sound Balance/Fader These two controls adjust the strength of the sound coming from each speaker. The Balance control adjusts the side- to-side strength, while the Fader control adjusts the front-to-back strength.


To adjust the fader, push on the BASS/FADER control knob to get it to pop out. Pull it out slightly farther, and adjust the front-to-back sound to your liking. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


To adjust the balance, push on the TREBLE/BALANCE control knob to get it to pop out. Pull it out slightly farther, and adjust the side-to-side sound to your liking. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


Audio System


BASS/FADER CONTROL


TREBLE/BALANCE CONTROL


Treble/Bass — Use these controls to adjust the tone to your liking.


To adjust the Treble level, push on the TREBLE/BALANCE control knob to get it to pop out. Without pulling it out farther, turn the knob to adjust the treble level. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


To adjust the Bass level, push on the BASS/FADER control knob to get it to pop out. Without pulling it out farther, turn the knob to adjust the bass level. Push the knob back in when you are done so you cannot change the setting by accidentally bumping it.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Audio System Lighting You can use the instrument panel brightness control dial to adjust the il- lumination of the audio system (see page 63). The audio system illuminates when the parking lights are on, even if the radio is turned off.


Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as "FM101."


Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:


AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz


Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).


Radio Reception How well your Honda's radio receives stations is dependent on many factors, such as the distance from the station's transmitter, nearby large objects, and atmos- pheric conditions.


A radio station's signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will


Comfort and Convenience Features


go off and the sound will fade completely as you get out of range of the station's signal.


Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio's reception. You may temporarily hear both stations, or hear only the station you are close to.


Main MenuTable of Contentsst Audio System


As required by the FCC: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.


Comfort and Convenience Features


Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.


Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.


Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.


Main MenuTable of Contentsst Audio System


Operating the CD Player You operate the CD player with the same controls used for the radio.


With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.


You can also play 3-inch (8-cm) discs without using an adapter ring. Play only standard round discs. Odd- shaped CDs may jam in drive or cause other problems.


When the system reaches the end of the disc, it will return to the begin- ning and play that disc again. You can switch to the radio while a CD is playing by pressing the A M/ FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off.


Comfort and Convenience Features


CD SLOT


AM/FM BUTTON


TUNE BAR


EJECT BUTTON


SEEK/SKIP BAR


CD BUTTON


RPT BUTTON


A. SEL/RDM BUTTON


Main MenuTable of Contentsst If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.


Press the eject button to remove the disc from the drive.


If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.


You can use the TUNE and SEEK/ SKIP bars while a disc is playing to select passages and change tracks.


To move rapidly within a track, press and hold the TUNE bar. Press the


side to move forward. You will


see CUE in the display. Press the side to move backward. You


will see REW displayed. Release the bar when the system reaches the point you want.


side of


Each time you press the the SEEK/SKIP bar, the system skips forward to the beginning of the next track. Press the side to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.


REPEAT — To activate the Repeat feature, press and release the RPT button. You will see RPT in the display. The system continuously


Audio System


replays the current track. Press the RPT button again to turn it off.


RANDOM PLAY — This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the. CD. To activate Random Play, press and release the A. SEL/RDM button. You will see RDM in the display. The system will then select and play tracks randomly. This continues until you deactivate Random Play by pressing A. SEL/RDM again.


If the system is in Repeat mode, you must turn it off by pressing the RPT button before selecting Random Play.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Operating the CD Changer (Optional) A Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player.


Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Odd- shaped CDs may jam in the drive or cause other problems.


Comfort and Convenience Features


AM/FM BUTTON


Loading...
x