Download PDF Manual


The moonroof has a key-off delay. You can still open and close the moonroof for up to ten minutes after you turn off the ignition. The key-off delay cancels as soon as you open either door. You must then turn the ignition ON (II) for the moonroof to operate.


NOTICE


If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.


MOONROOF SWITCH


Use the switch on the dashboard to open and close the moonroof. The ignition must be ON (II). Push and hold the switch to open the moonroof. Release the switch when the moonroof reaches the desired position. To close the moonroof, press and hold the


switch.


Closing the moonroof on someone's hands or fingers can cause serious injury.


Make sure passengers are clear of the moonroof before closing it.


Instruments and Controls


Main MenuTable of Contentsst Mirrors


Adjusting the Power Mirrors


SELECTOR SWITCH


TAB


Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.


The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.


Adjust the outside mirrors with the adjustment switch on the driver's door armrest:


3. Push the appropriate edge of the


adjustment switch to move the mirror right, left, up or down.


1. Turn the ignition switch ON (II).


2. Move the selector switch to L


(driver's side) or R (passenger's side).


4. When you finish, move the


selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Mirrors, Parking Brake


Parking Brake


NOTICE


HEATED MIRROR BUTTON


PARKING BRAKE LEVER


Driving the car with the parking brake applied can damage the rear brakes and axles.


Available on all Canadian models The outside mirrors are heated to re- move fog and frost. With the ignition ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off.


To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 31).


Instruments and Controls


Main MenuTable of Contentsst HOUR MIN RESET


To set the clock:


1. Turn the ignition switch ON (II) to


display the time.


2. Swing down the front cover of the


wide button under the clock display. You will see HOUR, MIN, and RESET buttons.


Digital Clock


You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET sets the clock back to the previous hour. If the displayed time is after the half hour, pressing RESET sets the clock forward to the beginning of the next hour.


The digital clock displays the time with the ignition switch ON (II).


3. Press and hold the HOUR button


until the hour advances to the desired time.


For example:


1:06 would RESET to 1:00. 1:52 would RESET to 2:00.


4. Press and hold the MIN button


until the numbers advance to the desired time.


Instruments and Controls


Main MenuTable of Contentsst Beverage Holder


PARTITION


Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior.


The front beverage holder is located on the center console. The partition in the beverage holder can be moved forward or backward. If you want to use the beverage holder, slide the partition forward until it clicks. To put small items in the beverage holder, slide the partition completely backward.


Use the beverage holder only when the car is parked. If you place cups in the holder while driving, the liquid may spill when you go over bumps or around corners.


Instruments and Controls


Main MenuTable of Contentsst Beverage Holder, Console Compartment


Console Compartment


LEVER


LEVER


The rear seat also has a beverage holder in the armrest on the driver's side.


CONSOLE COMPART- MENT


To open the console compartment, press the lower lever and lift the lid.


To close, lower the lid and push it down until it latches.


You can put small items in the tray located in the console compartment lid. To use the tray, press the upper lever and lift up the armrest pad.


Instruments and Controls


Main MenuTable of Contentsst Coin Box, Accessory Power Socket


Coin Box


Accessory Power Socket


The coin box is located next to the beverage holder. Open the lid by lifting it up.


To remove the coin box for emptying, lift the coin box up by pushing up on the middle edge of the coin box on the console guide. Never use the coin box for smoking materials.


Instruments and Controls


ACCESSORY POWER SOCKET


To use the accessory power socket, pull down the cover. The ignition switch must be in ACCESSORY (I) or ON (II).


This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).


It will not power an automotive type cigarette lighter element.


Main MenuTable of Contentsst Ashtrays (Optional) Front and rear ashtrays are available as options. The front ashtray fits In the coin box. The rear ashtray fits in the rear pocket on the rear seat armrest on the driver's side.


Open the rear ashtray by lifting up the lid. To remove the ashtray for emptying, open the lid and then lift it up and out.


NOTICE


Use the ashtray only for cigarettes, cigars, and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray.


Ceiling Lights


DOOR ACTIVATED


The ceiling light contains a main light as well as two spotlights.


Ashtrays, Interior Lights


The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open either door. After both doors are closed tightly, the light dims slightly, then fades out in about 10 seconds. In the ON position, the ceiling light stays on continuously.


CONTINUED


Instruments and Controls


Main MenuTable of Contentsst Interior Lights


Courtesy Lights


Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. You can use the spotlights at all times.


Your car has a courtesy light in the ignition switch. The ignition switch light comes on whenever you open either door. It remains on, then fades out in about 10 seconds after both doors are closed tightly.


The ignition switch light and ceiling light (with the switch in the center position) also comes on when you unlock the door with the key, the lock tab on the driver's door, or the


Instruments and Controls


master door lock switch. If you relock the driver's door or close the driver's door with the key in the ignition switch, the lights turns off immediately. Otherwise, the light remains on, then fades out in about 10 seconds.


If you keep the door open, the ceiling light (with the switch in the center position) will turn off after three minutes when the key is not in the ignition switch.


On Type SH Your car also has a courtesy light in each door. Each door light comes on when the door is opened, and goes out when the door is closed tightly.


Main MenuTable of Contentsst Comfort and Convenience Features


The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions.


The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.)


Your Honda has an anti-theft audio system that requires a code number to enable it.


Heating and Cooling........................ 70
What Each Control Does............ 70
How to Use the System............... 72
To Turn Everything Off............. 77
Audio System................................... 78
AM/FM/CD Audio System....... 78
Operating the Radio.................... 79
Adjusting the Sound.................... 82
Audio System Lighting............... 83
Radio Frequencies....................... 83
Radio Reception.....,...,...,..,..,,...... 83
Operating the CD Player............ 85
Operating the CD Changer........ 87
Protecting Compact Discs.......... 88
CD Player Error Indications....... 89
CD Changer Error Indications... 90
Operating the Cassette Player... 91
Tape Search Functions............... 92
Caring for the Cassette Player... 94
Theft Protection........................... 95


Comfort and Convenience Features


Main Menust Heating and Cooling


Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility.


What Each Control Does


Fan Control Lever Sliding this lever to the right increases the fan's speed, which increases air flow.


Temperature Control Lever Sliding this lever to the right increases the temperature of the air flow.


Air Conditioning (A/C) Button This button turns the air condi- tioning ON and OFF. The indicator in the button lights when the A/C is on.


Comfort and Convenience Features


MODE BUTTONS


REAR WINDOW DEFOGGER BUTTON


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


Rear Window Defogger Button This button turns the rear window defogger on and off (see page 41).


AIR CONDITIONING BUTTON


FAN CONTROL LEVER Recirculation Button This button controls the source of the air going into the system. When the indicator in this button is lit, air from the vehicle's interior is sent through the system again (Recircula- tion mode). When the indicator is off, air is brought in from outside the vehicle (Fresh Air mode).


Main MenuTable of Contentsst Mode Buttons Use the MODE buttons to select the vents the air flows from.


Air flows from the center


and corner vents in the dashboard.


Air flow is divided between the vents in the dashboard and the floor vents.


Air flows from the floor


vents.


Air flow is divided between


the floor vents and the defroster vents at the base of the windshield.


Air flows from the defroster vents at the base of the windshield.


When you select automatically switches to Fresh Air mode and turns on the A/C.


the system


Heating and Cooling


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


Vent Controls


CENTER VENT


SIDE VENT


You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-to- side.


The vents in the corners of the dashboard can be opened and closed with the dials underneath them.


Comfort and Convenience Features


How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting.


The engine must be running for the heater and air conditioning to generate hot and cold air. 'The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature.


Main MenuTable of Contentsst It Is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears.


The outside air intakes for the heating and cooling system are at the base of the windshield. Keep these clear of leaves and other debris.


Heating and Cooling


MODE BUTTONS


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear window.


FAN CONTROL LEVER 1. Slide the temperature control lever


AIR CONDITIONING BUTTON


all the way to the left. Make sure the A/C is off.


2. Select 3. Set the fan to the desired speed.


and Fresh Air mode.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst MODE BUTTONS


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Heating and Cooling


To Cool with A/C 1. Turn on the A/C by pressing the


button. The light in the button should come on.


2. Make sure the temperature


control lever is all the way to the left.


3. Select and Fresh Air mode. 4. Set the fan to the desired speed.


Comfort and Convenience Features


Main MenuTable of Contentsst If the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way:


1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the tempera- ture control lever is all the way to the left.


3. Set the fan to maximum speed. 4. Open the windows partially. Select


and Recirculation mode.


When the interior has cooled down to a more comfortable temperature, close the windows and set the controls as described for normal cooling.


Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 35) when driving in stop-and-go traffic or climbing a long, steep hill. If it moves near the red zone, turn off the A/C until the gauge reads normally.


To Heat To warm the interior:


1. Start the engine. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with


and Fresh Air mode.


the temperature control lever.


Heating and Cooling


To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.


1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control


and Fresh Air mode.


lever so the mixture of heated and cooled air feels comfortable.


This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Heating and Cooling


To Defog and Defrost To remove fog from the inside of the windows:


1. Switch the fan on. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


3. Adjust the temperature control


lever so the air flow from the defroster vents feels warm.


4. Turn on the rear window defogger


to help clear the rear window.


'When you switch to another mode from Press the A/C button to turn if off.


the A/C stays on.


Comfort and Convenience Features


MODE BUTTONS


REAR WINDOW DEFOGGER BUTTON


RECIRCULATION BUTTON


TEMPERATURE CONTROL LEVER


FAN CONTROL LEVER


AIR CONDITIONING BUTTON


Main MenuTable of Contentsst To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather:


1. Start the engine. 2. Select


When you select system automatically switches to Fresh Air mode and turns on the A/C.


the


3. Switch the fan and temperature


controls to maximum.


To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows.


Heating and Cooling


These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial underneath each vent. This will send more warm air to the windshield defroster vents.


For safety, make sure you have a clear view through all the windows before driving away.


To Turn Everything Off To shut off the system temporarily, slide the fan speed and temperature control levers all the way to the left,


You should shut the system completely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior.


Comfort and Convenience Features


Main MenuTable of Contentsst AM/FM 1-2 BUTTON


TUNE BAR


PWR/VOL KNOB


PRESET BUTTONS


SEEK BAR


Audio System


AM/FM/CD Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations.


The Anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 95 ).


Comfort and Convenience Features


Main MenuTable of Contentsst Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob.


The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM 1-2 button. On the FM band, ST will be displayed if the station is broad- casting in stereo. Stereo reproduc- tion on AM is not available.


You can use any of three methods to find radio stations on the selected band: TUNE, SEEK, or the Preset buttons.


TUNE — Use the TUNE bar to tune the radio to a desired frequency. Press the to a higher frequency, and the


side of the bar to tune


side to tune to a lower


frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly.


Audio System


SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press or the SEEK bar on either the


side, then release it.


Depending on which side you press, the system scans upward or down- ward from the current frequency. It stops when it finds a station with a strong signal.


Preset — You can store the fre- quencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two on the FM band.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst AM/FM 1-2 BUTTON


TUNE BAR


PRESET BUTTONS


SEEK BAR


Audio System


To store a frequency:


1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button.


2. Use the TUNE or SEEK function


to tune the radio to a desired station.


3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep.


4. Repeat steps 1 to 3 to store a total


of six stations on AM and twelve on FM.


Once a station's frequency is stored, simply press and release the proper Preset button to tune to it. The preset frequencies will be lost if your vehicle's battery goes dead, is disconnected or the radio fuse is removed.


Comfort and Convenience Features


Main MenuTable of Contentsst AUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area.


To activate Auto Select, press the A. SEL/RPT button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals. It stores the frequen- cies of six AM stations and twelve FM stations in the preset buttons. You can then use the preset buttons to select those stations.


If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a "0" displayed when you press any preset button that does not have a station stored.


Audio System


TUNE BAR


SEEK BAR


PRESET BUTTONS


AUTO SELECT/ REPEAT BUTTON


With Auto Select on, you cannot manually store any frequencies in the preset buttons. If you do not like the stations found by Auto Select, you can use the TUNE and SEEK functions to find other stations.


Auto Select does not erase the frequencies that you preset pre- viously. When you return home, turn off Auto Select by pressing the A. SEL/RPT button. The preset buttons will then select the fre- quencies you originally set.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the MODE button several times. The selected mode, BAS, TRE, FAD, or BAL is shown in the display.


Balance/Fader — These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.


Select BAL or FAD by pressing the MODE button. Adjust the Balance or Fader to your liking by turning the PWR/VOL knob. The number in the display (from — 9 to 9) shows you the current setting.


Comfort and Convenience Features


MODE BUTTON


PWR/VOL KNOB


Treble/Bass — Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the MODE button. Adjust the desired mode by turning the PWR/VOL knob. The displayed number (from — 5 to 5) shows you the current setting.


The system will automatically return the display to normal mode about seven seconds after you stop adjusting a mode with the PWR/ VOL knob. You can also continue pressing the MODE button until the frequency is displayed.


Main MenuTable of Contentsst Audio System Lighting You can use the MODE button to turn the Illumination on the audio system on or off when the headlighs are on.


Radio Frequencies Your Honda's radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:


Push and hold the MODE button for three seconds and the illumination will turn off. Push it again for three seconds to turn the illumination on.


AM band: 530 to 1,710 kilohertz FM band: 87.7 to 107.9 megahertz


Radio stations on the AM band are assigned frequencies at least ten kilohertz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).


Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as "FM101."


Audio System


Radio Reception How well your Honda's radio receives stations is dependent on many factors, such as the distance from the station's transmitter, nearby large objects, and atmos- pheric conditions.


A radio station's signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station's signal.


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio's reception. You may temporarily hear both stations, or hear only the station you are close to.


Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.


Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.


Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.


Comfort and Convenience Features


Main MenuTable of Contentsst Operating the CD Player You operate the CD player with the same controls used for the radio.


With the system on, insert the disc into the CD slot Push the disc in halfway, the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.


You can also play 3-inch (8-cm) discs without using an adapter ring.


When the system reaches the end of the disc, it will return to the begin- ning and play that disc again.


You can switch to the radio while a CD is playing by pressing the AM/ FM1-2 button. Press the CD button to return to playing the CD. The CD will begin playing where it left off.


Audio System


AM/FM1-2
BUTTON


CD BUTTON


CD SLOT


CD INDICATOR


PWR/VOL KNOB


EJECT BUTTON


REPEAT/RANDOM PLAY BUTTON


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.


Press the eject button to remove the disc from the drive.


If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.


Comfort and Convenience Features


RANDOM PLAY — This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press and hold the A. SEL/RPT button until you see A. SEL in the display. The system will then select and play tracks randomly. This continues until you deactivate Random Play by pressing A. SEL/RPT again.


If the system is in Repeat mode, you must turn it off by pressing A. SEL/ RPT before you can select Random Play. Then press and hold the button again until you see A. SEL displayed.


You can use the TUNE and SEEK bars while a disc is playing to select passages and changes tracks.


To move rapidly within a track, press and hold the TUNE bar. Press the side to move forward, or the side to move backward.


Release the bar when the system reaches the point you want.


side of


Each time you press the the SEEK bar, the system skips forward to the beginning of the next track. Press the side to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.


REPEAT — To activate the Repeat feature, press and release the Repeat button. You will see RPT in the display. The system continuously replays the current track. Press the Repeat button again to turn it off.


Main MenuTable of Contentsst Operating the CD Changer (Optional) A trunk-mounted Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player.


Load the desired CD's in the magazine and load the magazine in the changer according to the instructions that came with the unit.


To select the CD changer, press the CD button. The disc and track numbers will be displayed. A "0" will flash for the track number as the CD is loaded, then it will change to a non-flashing "1 " .


Audio System


To select a different disc, press the appropriate preset button (1—6). If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot. This continues until it finds a CD to load and play.


When you switch back to CD mode, the system selects the same unit (in- dash or changer) that was playing when you switched out of CD mode.


To use the SKIP, REPEAT, and RANDOM functions, refer to the in- dash player operating instructions.


If you load a CD in the in-dash player while the changer is playing a CD, the system will stop the changer and begin playing the in-dash CD. To select the changer again, press the CD button. Play will begin where it left off. Use the CD button to switch between the player and the changer.


If you eject the in-dash CD while it is playing, the system will automatically switch to the CD changer and begin play where it left off. If there are no CDs in the changer, the display will flash. You will have to select another mode (AM or FM) with the button.


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


Protecting Compact Discs


Handle a CD by its edges; never touch either surface. Contamination from fingerprints, liquids, felt-tip pens, and labels can cause the CD to not play properly, or possibly jam in the drive.


When a CD is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep CDs out of direct sunlight and extreme heat.


Comfort and Convenience Features


To clean a disc, use a clean soft cloth. Wipe across the disc from the center to the outside edge.


A new CD may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the re- cording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.


Never try to insert foreign objects in the CD player or the magazine.


Main MenuTable of Contentsst CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.


Audio System


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.


Comfort and Convenience Features


Main MenuTable of Contentsst Operating the Cassette Player (Optional) The cassette system features Dolby B* noise reduction, automatic sensing of chromium-dioxide (CrO2) tape, and autoreverse for continuous play.


Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.


* Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corpo- ration. "DOLBY" and the double-D symbol are trademarks of Dolby Laboratories


Licensing Corporation.


Audio System


FAST FORWARD/ REWIND


T MS


PROG BUTTON


DOLBY ON/OFF BUTTON


REPEAT BUTTON


CONTINUED


Comfort and Convenience Features


Main MenuTable of Contentsst Audio System


The tape direction indicator will light to show you which side of the indicates cassette is playing. The the side you inserted facing upward is now playing. If you want to play the other side, press the PROG button.


If you turn the system off while a tape is playing, either with the PWR/ VOL knob or by turning off the ignition, the cassette will remain in the drive. When you turn the system back on, the tape will begin playing where it left off.


Dolby B noise reduction turns on when you insert a cassette. If the tape was not recorded with Dolby B noise reduction, turn it off by pressing the NR button.


To switch to the radio or CD player while a tape is playing, press the AM/FM1-2 or CD button. To change back to the cassette player, push the CD button.


When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the EJECT button.


Comfort and Convenience Features


Tape Search Functions With a cassette playing, you can use the FF, REW, TMS, or REPEAT function to find a desired program.


side of the


FF/REW — Fast Forward and Rewind move the tape rapidly. Press and release the TUNE bar to fast forward the tape, or the side to rewind. You will see FF or REW flashing in the display. To stop fast forward or rewind, press the PLAY button. If the system reaches the end of the tape while in fast forward or rewind, it automatically stops that function, reverses direction, and begins to play.


Main MenuTable of Contentsst side to advance to the


TMS — The Tape Music Search function allows you to find the beginning of a song or passage. To activate TMS, press the SEEK bar. Press the beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.


REPEAT — The Repeat function continuously replays the current song or passage. Press the REPEAT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will


Audio System


FAST FORWARD/ REWIND


TMS


PROG BUTTON


DOLBY ON/OFF BUTTON


REPEAT BUTTON


continue to repeat this same program until you deactivate REPEAT by pressing the button again.


The TMS and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of a selection.


Comfort and Convenience Features


Main MenuTable of Contentsst When they are not in use, store cassettes in their cases to protect them from dust and moisture. Never place cassettes where they will be exposed to direct sunlight, high heat, or high humidity. If a cassette is exposed to extreme heat or cold, let it reach a moderate temperature before inserting it in the player.


Never try to insert foreign objects into the cassette player.


Audio System


Caring for the Cassette Player The cassette player picks up dirt and oxides from the tape. This contami- nation builds up over time and causes the sound quality to degrade. To prevent this, you should clean the player after every 30 hours of use. Your dealer has a cleaning kit available.


If you do not clean the cassette player regularly, it may eventually become impossible to remove the contamination with a normal cleaning kit.


Comfort and Convenience Features


The player automatically ejects cassettes that do not play properly. If it ejects a cassette before it begins to play, it is probably defective and should not be inserted again. You may have a cassette suddenly stop playing, reverse directions once or twice and then eject. This is normally an indication the tape is wound unevenly. It should play after the tape is manually rewound.


Use 100-minute or shorter cassettes. Cassettes longer than that use thinner tape that may break or jam the drive.


Look at the cassette before you insert it. If the tape is loose, tighten it by turning a hub with a pencil or your finger. If the label is peeling off, remove it from the cassette or it could cause the cassette to jam in the player. Never try to insert a warped or damaged cassette in the player.


Main MenuTable of Contentsst Theft Protection Your car's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, the user must enter a specific five-digit code in the Preset buttons. Because there are hundreds of number combinations possible from five digits, making the system work without knowing the exact code is nearly impossible.


You should have received a card that lists your audio system's code number and serial number. It is best to store this card in a safe place at home. In addition, you should write the audio system's serial number in this Owner's Manual. If you should happen to lose the card, you must obtain the code number from your Honda dealer. To do this, you will need the system's serial number.


If your car's battery is disconnected or goes dead, the audio system will disable itself. If this happens, you will see "Code" in the frequency display the next time you turn on the system. Use the Preset buttons to enter the five-digit code. If it is entered correctly, the radio will start playing.


If you make a mistake entering the code, do not start over or try to correct your mistake. Complete the five-digit sequence, then enter the correct code. You have three tries to enter the correct code. If you are unsuccessful in three attempts, you must then leave the system on for one hour before trying again.


Audio System


You will have to store your favorite stations in the Preset buttons after the system begins working. Your original settings were lost when power was disconnected.


Comfort and Convenience Features


Main MenuTable of Contentsst Before you begin driving your Honda, you should know what gasoline to use, and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your car, please read the information in this section first.


Before Driving


Break-in Period................................ 98
Gasoline............................................ 98
Oxygenated Fuels........................ 98
Driving in Foreign Countries..... 99
Service Station Procedures.......... 100
Filling the Fuel Tank................. 100
Opening the Hood..................... 101
Oil Check................................ 102
Engine Coolant Check.......... 103
Fuel Economy................................ 104
Vehicle Condition...................... 104
Driving Habits............................ 104
Accessories..................................... 105
Loading Cargo................................ 106


Before Driving


Main Menust Break-in Period, Gasoline


Break-in Period Help assure your car's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:


Avoid full-throttle starts and rapid acceleration.


Avoid hard braking. New brakes need to be broken-in by moderate use for the first 200 miles (300
km).


You should follow these same re- commendations with an overhauled or exchanged engine, or when the brakes are relined.


Gasoline Your Honda is designed to operate on premium unleaded gasoline with a pump octane number of 91 or higher.


If you are unable to find premium unleaded gasoline, you may substi- tute an unleaded regular gasoline. The engine will compensate for the lower octane, but you may notice a slight decrease in power as a result.


We recommend gasolines containing detergent additives that help prevent fuel system and engine deposits.


Using gasoline containing lead will damage your car's emission controls. This contributes to air pollution.


In Canada, some gasolines contain an octane-enhancing additive called MMT. If you use such gasolines, your emission control system performance may deteriorate and the Malfunction Indicator Lamp on your instrument panel may turn on. If this happens, contact your authorized Honda dealer for service.


Oxygenated Fuels Some conventional gasolines are being blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions.


If you use an oxygenated fuel, be sure it is unleaded and meets the minimum octane rating requirement.


Before Driving


Main MenuTable of Contentsst Gasoline


Before using an oxygenated fuel, try to confirm the fuel's contents. Some states/provinces require this information to be posted on the pump.


The following are the EPA-approved percentages of oxygenates:


ETHANOL (ethyl or grain alcohol) You may use gasoline containing up to 10 percent ethanol by volume. Gasoline containing ethanol may be marketed under the name "Gasohol."


MTBE (Methyl Tertiary Butyl Ether) You may use gasoline containing up to 15 percent MTBE by volume.


METHANOL (methyl or wood alcohol) You may use gasoline containing up to 5 percent methanol by volume as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5 percent methanol by volume may cause starting and/or performance problems. It may also damage metal, rubber and plastic parts of your fuel system.


If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.


Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates given above are not covered under warranty.


Driving in Foreign Countries If you are planning to take your Honda outside the U.S. or Canada, contact the tourist bureaus in the areas you will be traveling in to find out about the availability of unleaded gasoline with the proper octane rating. If unleaded gasoline is not available, be aware that using leaded gasoline in your Honda will affect perform- ance and fuel mileage, and damage its emissions controls. It will no longer comply with U.S. and Canadian emissions regulations, and will be illegal to operate in North America. To bring your car back into compliance will require the replace- ment of several components, such as the oxygen sensors and the three way catalytic converter. These replacements are not covered under warranty.


Before Driving


Main MenuTable of Contentsst Service Station Procedures


Filling the Fuel Tank


Pull


1. Because the fuel fill cap is on the driver's side of the car, park with that side closest to the service station pumps.


2. Open the fuel fill door by pulling


on the handle to the left of the driver's seat.


Before Driving


Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.


Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately.


FUEL FILL CAP


3. Remove the fuel fill cap slowly.


You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door.


4. Stop filling the tank after the fuel pump automatically clicks off. Do not try to "top off" the tank, leave some room for the fuel to expand with temperature changes.


5. Screw the fuel fill cap back on,


tighten it until it clicks. If you do not properly tighten the cap, the Malfunction Indicator Lamp may come on (see page 214).


6. Push the fuel fill door closed until


it latches.


Main MenuTable of Contentsst Opening the Hood


Service Station Procedures


SUPPORT ROD


CLIP


LATCH


HOOD RELEASE HANDLE


1. Shift to Park or Neutral and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.


2. Standing in front of the car, put


your fingers under the front edge of the hood to the right of center. Slide your hand to the left until you feel the hood latch handle. Push this handle to the left until it releases the hood. Lift the hood.


3. Pull the support rod out of its clip


and insert the end into the hole on the left side of the hood.


To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot above the fender, then let it drop.


CONTINUED


Before Driving


Main MenuTable of Contentsst Service Station Procedures


Oil Check


DIPSTICK


Check the engine oil level every time you fill the car with fuel. Wait at least two minutes after turning the engine off before you check the oil.


1. Remove the dipstick (orange


handle).


Before Driving


2. Wipe the dipstick with a clean


cloth or paper towel.


3. Insert it all the way back in its tube.


Main MenuTable of Contentsst Engine Coolant Check


Service Station Procedures


Refer to Owner Maintenance Checks on page 144 for information on checking other items in your Honda.


MAX


MIN


UPPER MARK LOWER MARK


4. Remove the dipstick again and


check the level. It should be between the upper and lower marks.


If it is near or below the lower mark, see Adding Oil on page 146.


RESERVE TANK


Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If it is below the MIN line, see Adding Engine Coolant on page 150 for information on adding the proper coolant.


Before Driving


Main MenuTable of Contentsst Driving Habits You can improve fuel economy by driving moderately. Rapid acceler- ation, abrupt cornering, and hard braking use more fuel.


Always drive in the highest gear that allows the engine to run and acceler- ate smoothly.


Depending on traffic conditions, try to maintain a constant speed. Every time you slow down and speed up, your car uses extra fuel. Use the cruise control, when appropriate, to increase fuel economy.


A cold engine uses more fuel than a warm engine. It is not necessary to "warm-up" a cold engine by letting it idle for a long time. You can drive away in about a minute, no matter how cold it is outside. The engine will warm up faster, and you get better fuel economy. To cut down on the number of "cold starts," try to combine several short trips into one.


The air conditioning puts an extra load on the engine which makes it use more fuel. Turn off the A/C to cut down on air conditioning use. Use the flow-through ventilation when the outside air temperature is moderate.


Fuel Economy


The condition of your car and your driving habits are the two most important things that affect the fuel mileage you get.


Vehicle Condition Always maintain your car according to the maintenance schedule. This will keep it in top operating condition.


An important part of that mainte- nance is the Owner Maintenance Checks (see page 144). For example, an underinflated tire causes more "rolling resistance," which uses fuel. It also wears out faster, so check the tire pressure at least monthly.


In winter, the build-up of snow on your carz's underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion.


Before Driving


Main MenuTable of Contentsst Your Honda dealer has many Genuine Honda Accessories that allow you to personalize your car. These have all been approved for installation and use on your car, and are covered by warranty.


Accessories


Some non-Honda accessories you can buy in the "aftermarket" are designed for universal applications. Although they may fit your Honda, they may not be within factory specifications. For example, after- market wheels may not meet Honda's specifications for width and offset. They could cause suspension problems that would not be covered by your warranty. Improperly- designed accessories can adversely affect your car's handling and stability.


Electronic communications equip- ment, such as cellular telephones and two-way radios are regulated by the FCC (DOC in Canada) and should not interfere with your car's systems. Improper installation, or using electrical equipment not in- tended for mobile use may interfere with your car's operation. If you want to install a cellular telephone, other mobile communications equipment or even add-on stereo amplifiers, please discuss it first with your Honda dealer.


Your car has several computer- controlled systems, including the SRS system, the engine's fuel injection, and the Anti-lock brake system. Strong electronic inter- ference can affect their operation.


In many cases, improper installation is the real cause of problems with aftermarket accessories. Have these accessories installed by qualified technicians who are familiar with your Honda. If possible, have your Honda dealer inspect the final installation.


Before Driving


Main MenuTable of Contentsst Loading Cargo


The maximum load you can carry in your Honda is 700 Ibs (325 kg). It includes the total weight of all passengers and their belongings, any accessories, and the tongue weight of a trailer. This 700 Ibs (325 kg) figure is shown as the Vehicle Capacity Weight on the tire infor- mation label attached to the driver's doorjamb.


Before Driving


To figure out how much cargo you can carry:


Figure the total "occupant weight" you will be transporting. To do this, multiply the number of people (driver and all passengers) by 150
Ibs (70 kg).


Subtract this number from the Vehicle Capacity Weight (700 Ibs/ 325 kg).


If you are towing a trailer, subtract the tongue weight. See Towing a Trailer on page 128.


This final number is the total weight of cargo you can load in or on the car. With four occupants (driver and three passengers), the maximum recommended weight for cargo is 100 Ibs (45 kg).


Where you store this cargo, and how well you secure it, are just as important as how much it weighs. Make sure you load cargo so it will not shift while driving. Items stored in the trunk should be stored as far forward as possible. You could store additional items on the floor behind the front seats. Make sure they cannot roll under the front seat and interfere with the pedals.


If you must carry large objects that prevent you from closing the trunk lid, be aware that exhaust gas can enter the interior. See Carbon Monoxide Hazard on page 25.


Never place items on the shelf behind the back seat. Those items can fly forward and injure you or your passengers if you brake hard or are involved in a collision.


Main MenuTable of Contentsst This section gives you tips on starting the engine under various conditions, and how to operate the 5-speed manual and automatic transmissions. It also includes important information on parking your car, the braking system, and facts you need if you are planning to tow a trailer.


Driving


Preparing to Drive......................... 108
Starting the Engine........................ 109


Starting in Cold Weather


at High Altitude..................... 109
5-speed Manual Transmission..... 110
Recommended Shift Points...... 111
Maximum Speeds ..................... 111
Automatic Transmission............... 112
Shift Lever Position Indicator.. 112
Shift Lever Positions................. 113
Maximum Speeds...................... 118
Shift Lock Release..................... 119
Parking............................................ 120
The Braking System...................... 121
Brake Wear Indicators.............. 121
Brake System Design................ 122
Anti-lock Brakes........................ 122


Important Safety


Reminders.......................... 123
ABS Indicator......................... 124
Active Torque Transfer System.. 125
Driving in Bad Weather................ 126
Towing a Trailer............................ 128


Driving


Main Menust 10.Turn the ignition ON (II). Check the indicator lights in the instru- ment panel.


11.Start the engine (see page 109).


12.Check the gauges and indicator


lights in the instrument panel (see page 29).


5. Check the adjustment of the seat


(see page 53).


6. Check the adjustment of the


inside and outside mirrors (see page 61).


7. Check the adjustment of the steering wheel (see page 42).


8. Make sure the doors are securely


closed and locked.


9. Fasten your seat belt. Check that


your passengers have fastened their seat belts (see page 7).


Preparing to Drive


You should do the following checks and adjustments every day before you drive your car.


1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.


2. Check that the hood and trunk are


fully closed.


3. Visually check the tires. If a tire


looks low, use a gauge to check its pressure.


4. Check that any items you may be


carrying with you inside are stored properly or fastened down securely.


Driving


Main MenuTable of Contentsst 1. Apply the parking brake.


2. In cold weather, turn off all


electrical accessories to reduce the drain on the battery.


3. Manual Transmission:


Push the clutch pedal down all the way. START (III) does not function unless the clutch pedal is depressed,


Automatic Transmission: Make sure the shift lever is in Park. Press on the brake pedal.


4. Without touching the accelerator pedal, turn the ignition key to the START (III) position. If the engine does not start right away, do not hold the key in START (III) for more than 15 seconds at a time. Pause for at least 10 seconds before trying again.


5. If the engine does not start within


15 seconds, or starts but stalls right away, repeat step 4 with the accelerator pedal pressed half-way down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.


6. If the engine still does not start,


press the accelerator pedal all the way down and hold it there while starting in order to clear flooding. As before, keep the ignition key in the START (III) position for no more than 15 seconds. Return to step 5 if the engine does not start. If it starts, lift your foot off the accelerator pedal so the engine does not race.


Starting in Cold Weather at High Altitude (Above 8,000 feet/ 2,400 meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400


Starting the Engine


meters) adds to the problem. Use the following procedure:


1. Turn off all electrical accessories


to reduce the drain on the battery.


2. Push the accelerator pedal half- way to the floor and hold it there while starting the engine. Do not hold the ignition key in START (III) for more than 15 seconds. When the engine starts, release the accelerator pedal gradually as the engine speeds up and smooths out.


3. If the engine fails to start in step 2,


push the accelerator pedal to the floor and hold it there while you try to start the engine for no more than 15 seconds. If the engine does not start, return to step 2.


Driving


Main MenuTable of Contentsst 5-speed Manual Transmission


Rapid slowing or speeding-up can cause loss of control on slippery surfaces. If you crash, you can be injured.


Use extra care when driving on slippery surfaces.


Come to a full stop before you shift into Reverse. You can damage the transmission by trying to shift into Reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into Reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind".


When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure engine speed will not go into the tachometer's red zone in the lower gear. Refer to the Maximum Speeds chart.


The manual transmission is syn- chronized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from Fifth to Reverse. When shifting up or down, make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.


Driving


Main MenuTable of Contentsst 5-speed Manual Transmission


Recommended Shift Points Drive in the highest gear that lets the engine ran and accelerate smoothly. This will give you the best fuel economy and effective emis- sions control. The following shift points are recommended:


Maximum Speeds The speeds in this table are the maximums for the given gears. If you exceed these speeds, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the RPM below the red zone.


Driving


Main MenuTable of Contentsst Automatic Transmission


Your Honda's transmission has four forward speeds, and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks.


Shift Lever Position Indicator


The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceler- ation and have the transmission checked by an authorized Honda dealer as soon as possible.


This indicator in the tachometer shows which shift position the shift lever is in. The illuminated number next to the "D4" indicator shows you the gear you have selected in the Sequential SportShift mode.


Driving


Main MenuTable of Contentsst Shift Lever Positions


To select the Sequential SportShift mode, slide the shift lever toward the left from the "D4" position. In this mode the shift lever allows you to shift up and down manually.


SHIFT LEVER


SEQUENTIAL SPORTSHIFT MODE POSITION


The shift lever has eight positions. It must be in Park or Neutral to start the engine. When you are stopped in D4, D3, 2,1, N, R, or the Sequential SportShift mode, press firmly on the brake pedal and keep your foot off the accelerator pedal.


Automatic Transmission


Whenever you move the shift lever, slide it along the guide on the console.


You cannot shift out of Park with the brake pedal depressed when the ignition switch is in LOCK (0) or ACCESSORY (I).


CONTINUED


Driving


Main MenuTable of Contentsst Automatic Transmission


Park (P) — This position mechani- cally locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Move the shift lever to the right to shift out of the Park position.


If you have done all of the above and still cannot move the lever out of Park, see Shift Lock Release on page 119.


Driving


Reverse (R) — To shift to Reverse from Park, see the explanation under Park. To shift to Reverse from Neutral, come to a complete stop and then shift.


Your car has a reverse lockout so you cannot accidentally shift to

Loading...
x