1997 Honda Prelude Owners Manual

Download PDF Manual
TRUNK-QPEM INDICATOR DOOR-OPEN INDICATOR SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR* ANTI-LOCK BRAKE SYSTEM INDICATOR* IMMOBlLIZER SYSTEM INDICATOR LOW OIL PRESSURE INDICATOR SEAT BELT REMINDER LIGHT LOW FUEL INDICATOR CHARGING SYSTEM INDICATOR HIGH BEAM INDICATOR CRUISE CONTROL INDICATOR * The U.S. instrument panel is shown. Differences for the Canadian model are noted in the text. Instruments and Controls Main MenuTable of ContentsstIndicator Lights Seat Belt Reminder Light This indicator lights when you turn the ignition ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt. If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition. MALFUNCTION INDICATOR LAMP TRUNK-OPEN INDICATOR DOOR-OPEN INDICATOR SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR* ACTIVE TORQUE TRANSFER SYSTEM INDICATOR ANTI-LOCK BRAKE SYSTEM INDICATOR* IMMOBILIZER SYSTEM INDICATOR LOW OIL PRESSURE INDICATOR CHARGING SYSTEM INDICATOR SEAT BELT REMINDER LIGHT LOW FUEL INDICATOR HIGH BEAM INDICATOR CRUISE CONTROL INDICATOR * The U.S. Type SH instrument panel is shown. Differences for the Canadian model are noted in the text. Instruments and Controls Main MenuTable of ContentsstSupplemental Restraint System Indicator S R S This indicator lights when you turn the ignition ON (II). If it comes on at any other time, it indicates a problem in the supplemental restraint system. For complete information, see page 14 . Immobilizer System Indicator This indicator should come on for a few seconds when you turn the igni- tion switch ON (II). It will then go off if you have inserted a properly- coded ignition key. If it is not a prop- erly-coded key, the indicator will blink and the engine will not start (see page 47 ). This indicator also blinks several times when you remove the key from the ignition switch. Charging System Indicator If this light comes on when the engine is running, the battery is not being charged. For complete information, see page 213. Low Oil Pressure Indicator The engine can be severely damaged if this light flashes or stays on when the engine is running. For complete information, see page 212 . Malfunction Indicator Lamp See page 214. Cruise Control Indicator CRUISE CONTROL This lights when you set the cruise control. See page 43 for information on operating the cruise control. Indicator Lights Canada U.S. BRAKE Parking Brake and Brake System Indicator This light has two functions: 1. It lights as a reminder that you have not released the parking brake. Driving with the parking brake applied can damage the brakes and tires. 2. If it remains lit after you release the parking brake while the engine is running, or comes on while driving, it can indicate that the brake fluid level is low. This is normally due to worn brake pads. Have your dealer check the braking system for worn pads or fluid leaks. Instruments and Controls Main MenuTable of ContentsstIndicator Lights Canada Anti-lock Brake System (ABS) Indicator U.S. A B S This light normally comes on for a few seconds when you turn the ignition ON (II), and when the ignition switch is turned to START (III). If this light comes on at any other time, there is a problem in the ABS. If this happens, take the car to your dealer to have it checked. With the light on, your car still has normal braking ability but no anti-lock. Active Torque Transfer System Indicator ATTS Type SH only This indicator normally comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, there is a problem in the Active Torque Transfer System (ATTS). If this happens, take the car to your dealer to have it checked. With the indicator on, your car will corner normally, but you will not have active torque transfer. Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 182 ). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling. When you turn on the Hazard Warning switch, both turn signal lights blink. All turn signals on the outside of the car should flash. Instruments and Controls Main MenuTable of ContentsstTrunk-open Indicator Low Fuel Indicator This light comes on if the trunk lid is not closed tightly. Door-open Indicator This light comes on if either door is not closed tightly. High Beam Indicator This light comes on with the high beam headlights. See page 38 for information on the headlight controls. On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page 38). LOW FUEL INDICATOR This indicator is located in the fuel gauge. It comes on as a reminder that you must refuel soon. Indicator Lights "Daytime Running Lights" Indicator D R L Canadian models only This indicator lights when you turn the ignition to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Instruments and Controls Main MenuTable of ContentsstGauges TACHOMETER SPEEDOMETER TRIP METER FUEL GAUGE TEMPERATURE GAUGE ODOMETER MAINTENANCE REQUIRED INDICATOR TRIP METER RESET BUTTON Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h). Tachometer The tachometer shows the engine speed in revolutions per minute (rpm). To protect the engine from damage, never drive with the tachometer needle in the red zone. Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph). Instruments and Controls Odometer The odometer shows the total dis- tance your car has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under federal law (in the U.S.) and provincial regulations (in Canada) to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated. Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. To reset it, push the trip meter reset button. Main MenuTable of ContentsstTACHOMETER SPEEDOMETER TRIP METER FUEL GAUGE TEMPERATURE GAUGE ODOMETER MAINTENANCE REQUIRED INDICATOR TRIP METER RESET BUTTON Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads. The gauge stays at the same fuel level reading after you turn off the ignition. When you add fuel, the gauge slowly changes to the new reading after you turn the ignition back ON (II). Gauges Temperature Gauge This shows the temperature of the engine's coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to near the upper white mark. If it reaches the red (Hot) mark, pull safely to the side of the road. Turn to page 210 for instructions and precautions on checking the engine's cooling system. Instruments and Controls Main MenuTable of ContentsstWhen the distance driven since the last scheduled maintenance nears 7,500 miles (12,000 km), the indicator will turn yellow. If you exceed 7,500 miles (12,000 km), the indicator will turn red. Your dealer will reset the indicator when he performs the scheduled maintenance. If someone else performs the maintenance, reset the indicator by inserting your master or valet key in the slot beside the indicator. Gauges Maintenance Required Indicator SLOT INDICATOR This indicator reminds you that it is nearing 7,500 miles (12,000 km) since the last scheduled maintenance. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages 140 — 141. Instruments and Controls Main MenuTable of ContentsstControls Near the Steering Wheel CRUISE CONTROL INSTRUMENT PANEL BRIGHTNESS HAZARD WARNING LIGHTS WINDSHIELD WIPERS/WASHERS The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers. The controls under the left air vent are for the moonroof, cruise control and instrument panel brightness. The switches for the hazard warning lights and rear window defogger are to the right of the steering column. The tilt adjustment lever on the underside of the steering column allows you to tilt the steering wheel. MOONROOF HEADLIGHTS/ TURN SIGNALS TILT ADJUSTMENT HORN BUTTONS REAR WINDOW DEFOGGER Instruments and Controls Main MenuTable of ContentsstControls Near the Steering Wheel Headlights If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder chime when you open the driver's door. The rotating switch on the left lever controls the lights. Turning this switch to the on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the position turns on the headlights. position turns Instruments and Controls To change between low beams and high beams, pull the turn signal lever until you hear a click, then let go. The blue high beam indicator will light (see page 33). To flash the high beams, pull the turn signal lever back lightly, then release it. The high beams will come on and go off. The high beams will stay on for as long as you hold the lever back, no matter what position the headlight switch is in. Daytime Running Lights (Canadian Models) With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch. Main MenuTable of ContentsstInstrument Panel Brightness Turn Signals Controls Near the Steering Wheel To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it. The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness. TURN SIGNAL LEVER Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn. Instruments and Controls Main MenuTable of ContentsstControls Near the Steering Wheel Windshield Wipers The right lever controls the wind- shield wipers and washers. The rotary switch at the end of the lever has three positions: INT: intermittent : low speed : high speed In intermittent, the wipers operate every few seconds. You can vary how often the wipers sweep the windshield by turning the INT TIME ring next to the rotary switch. In low speed and high speed, the wipers run continuously. To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield. Instruments and Controls Main MenuTable of ContentsstWindshield Washers Hazard Warning Rear Window Defogger Controls Near the Steering Wheel To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever. The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it. Push the red button to the left of the clock to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your car is disabled. The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 25 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the car. CONTINUED Instruments and Controls Main MenuTable of ContentsstControls Near the Steering Wheel Make sure the rear window is clear and you have good visibility before starting to drive. The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side. Instruments and Controls Steering Wheel Adjustment You can adjust the steering wheel height to suit your preference. Do this before you begin driving. Adjusting the steering wheel position while driving may cause you to lose control of the car and be seriously injured in a crash. Adjust the steering wheel only when the car is stopped. 1. Adjust the seat so you are a comfortable distance from the pedals and can operate them safely. 2. The lever to tilt the steering wheel is under the steering column to the left. Push this lever all the way down. 3. Move the steering wheel up or down to the desired position. Position the wheel so you can see all the instrument panel gauges and warning lights. Push the lever up to lock the steering wheel in that position. 4. Make sure you have securely locked the steering wheel in place by trying to move it up and down. Main MenuTable of ContentsstCruise Control Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions. Improper use of the cruise control can lead to a crash. Use the cruise control only when traveling on open highways in good weather. Steering Wheel Controls NOTICE Using the Cruise Control The cruise control, as it operates, moves the accelerator pedal. You can damage your car's accelerator mechanism by resting your foot under the pedal and blocking the movement. CRUISE CONTROL MASTER SWITCH 1. Push in the Cruise Control Master Switch to the left of the steering column. The indicator in the switch will light. 2. Accelerate to the desired cruising speed above 25 mph (40 km/h). CONTINUED Instruments and Controls Main MenuTable of ContentsstChanging the Set Speed You can increase the set cruising speed in either of two ways: Press and hold the RESUME/ accel button. The car will acceler- ate slowly. When you reach the desired cruising speed, release the button. Push on the accelerator pedal. Ac- celerate to the desired cruising speed and press the SET/decel button. You can decrease the set cruising speed in either of two ways: Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed. Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out. When the car slows to the desired speed, press the SET/decel button. The car will then maintain the desired speed. Steering Wheel Controls RESUME/ accel SET/decel 3. Press and hold the SET/decel button on the steering wheel until the CRUISE CONTROL light on the instrument panel comes on. This shows the system is now activated. The set speed may vary slightly, particularly on hills. Instruments and Controls Main MenuTable of ContentsstEven with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed. Resting your foot on the brake or clutch pedal will cause the cruise control to cancel. Cancelling the Cruise Control You can cancel the cruise control in any of these ways: Tap the brake or clutch pedal. Press the SET/decel and RE- SUME/accel buttons at the same time. Press the Cruise Control Master Switch. When you tap the brake or clutch pedal, or press the SET and RE- SUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way. If you use the brake or clutch pedal to cancel cruise control, the system remembers the previously-set cruising speed. To return to that Steeling Wheel Controls speed, accelerate to above 25 rnph (40 km/h) and press the RESUME/ accel button until the CRUISE CON- TROL light comes on. The car will accelerate to the same cruising speed as before. If you cancel cruise control by pressing the SET and RESUME buttons at the same time, the previously-set cruising speed is erased. To use the cruise control, accelerate to the desired cruising speed and press the SET/decel button. Pressing the Cruise Control Master Switch turns the system completely off and erases the previous cruising speed from memory. To use the system again, refer to Using the Cruise Control. Instruments and Controls Main MenuTable of ContentsstKeys and Locks Keys KEY NUMBER PLATE VALET KEY (Gray) MASTER KEY (BIack) LEARNING KEY (Red) Your vehicle comes with two kinds of keys: a master key and a valet key. The master key fits all the locks on your vehicle: Ignition Doors Trunk Trunk release handle Rear seat trunk access Glove box The valet key works only in the ignition and the door locks. You can keep the trunk, trunk release handle, rear seat trunk access and the glove box locked when you leave your vehicle and the valet key at a parking facility. You should have received a key number plate with your keys. You will need this key number if you ever have to get a lost key replaced. Keep Instruments and Controls the plate stored in a safe place. If you need to replace a key, use only Honda-approved key blanks. These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged. Protect the keys from direct sunlight, high temperature, and high humidity. Do not drop the keys or set heavy objects on them. Keep the keys away from liquids. If they get wet, dry them immedi- ately with a soft cloth. The keys do not contain batteries. Do not try to take them apart. Main MenuTable of ContentsstLearning Key If you attempt to use the learning key to start your vehicle's engine, it may cause a malfunction in the system that makes your master and valet keys unusable. If this happens, you should contact your Honda dealer. If you need a new key made, take the key number plate, the learning key, and all other keys that came with your car to your Honda dealer. You should also receive a small case containing a learning key. It is used by the Honda dealer to code replace- ment keys to your vehicle's Immobilizer System. It must not be used in your vehicle's ignition switch. Store the learning key with the key number plate in a safe place. Keys and Locks Immobilizer System The Immobilizer System protects your vehicle from theft. A properly- coded master or valet key must be used in the ignition switch for the engine to start. If an improperly- coded key (or other device) is used, the engine's starting circuit is disabled. When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again. If the system repeatedly does not recognize the coding of your key, contact your Honda dealer. CONTINUED Instruments and Controls Main MenuTable of ContentsstKeys and Locks Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable. If you have lost your key and you cannot start the engine, contact your Honda dealer. Instruments and Controls As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with DOC rules in Canada. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Ignition Switch The ignition switch is on the right side of the steering column. It has four positions: LOCK (0) ACCESSORY (I) ON (II) START (III) Main MenuTable of ContentsstLOCK (0) — You can insert or remove the key only in this position. When you turn the key from LOCK to ACCESSORY, you may have to turn the steering wheel to release the anti-theft lock. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic trans- mission, it must also be in Park. The anti theft lock will lock the steering column when you remove the key. Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control. Remove the key from the ignition switch only when parked. ACCESSORY (I) — In this position, you can operate the audio system and the accessory power socket. ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instru- ment panel come on as a test when you turn the ignition switch from ACCESSORY to ON (see page 29). START (III) — Use this position only to start the engine. The switch returns to ON (II) when you let go of the key. The engine will not start if the Immobilizer System does not recognize the key's coding (see page 47). Keys and Locks You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper. Instruments and Controls Main MenuTable of ContentsstKeys and Locks Power Door Locks Each door has a master door lock switch. Either switch locks and unlocks both doors. Push the switch down to lock both doors and up to unlock them. Each door has a lock tab next to the inside door handle. When you push in the lock tab on the driver's door, both doors lock. Pulling out the lock tab on the driver's door only unlocks that door. The lock tab on the passenger's door only locks and unlocks that door. Instruments and Controls To lock the passenger's door when getting out of the car, push the lock tab in and close the door. To lock the driver's door, remove the key from the ignition switch and push the lock tab in or push the master switch down, then close the door. Both doors can be locked from the outside by using the key in either door. To unlock only the driver's door from the outside, insert the key in the driver's door lock, turn the key and release it. If you turn the key and hold it, both doors will unlock. Both doors will unlock when you unlock the passenger's door with the key. Main MenuTable of ContentsstTrunk Lockout Prevention If you forget and leave the key in the ignition switch, Lockout Prevention will not allow you to lock the driver's door. With either door open and the key in the ignition, the master door lock switches are disabled. If you try to lock the driver's door by pushing in the lock tab, the tabs on both doors immediately pop out. Keys and Locks MASTER KEY TRUNK RELEASE HANDLE You can open the trunk in two ways: Pull the trunk release handle to the left of the driver's seat. Use the master key to open the trunk lock. The valet key does not work in this lock. To close the trunk, press down on the trunk lid. See page 106 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 25 . CONTINUED Instruments and Controls Main MenuTable of ContentsstAn open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt. Always keep the glove box closed while driving. Keys and Locks Glove Box MASTER KEY To protect items in the trunk when you need to give the key to someone else, lock the trunk release handle with the master key and give the other person the valet key. Open the glove box by pulling the bottom of the handle. Close it with a firm push. Lock or unlock the glove box with the master key. Instruments and Controls Main MenuTable of ContentsstFront Seat Adjustments Adjust the seat before you start driving. To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position. To change the angle of the seat-back, pull up on the lever on the outside of the seat bottom. Move the seat-back to the desired position and release the lever. Let the seat-back latch in the new position. Seat Adjustments Reclining the seat-back can decrease the protection you get from your seat belt in a crash. You can slide under the seat belt and be seriously injured. Adjust the seat-back to an upright position and sit well back in the seat. Instruments and Controls Main MenuTable of ContentsstSeat Adjustments Driver's Seat Height Adjustment Rear Seat Access To get into the back seat on the driver's side, pull up on the seat-back adjustment lever. RELEASE LEVER The height of your driver's seat is adjustable. Turn the dial on the outside of the seat cushion to change the height. Instruments and Controls To get into the back seat on the passenger's side, push forward on the release lever at the base of the seat-back. The seat-back will tilt forward and the entire seat will move forward to allow easier entry to the back seat. After you return the seat- back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before sitting in it. Main MenuTable of ContentsstThe front head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down. To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button and pull the restraint out of the seat- back. Head Restraints RELEASE BUTTON The front head restraints help protect you and your passenger from whiplash and other injuries. They are most effective when you adjust them so the top of the restraint is even with the top of your ears. Seat Adjustments Driving your car without head restraints can lead to serious injury to you and your passenger in a crash. Make sure the head restraints are in place and adjusted properly before driving. Instruments and Controls Main MenuTable of ContentsstSeat Heaters, Folding Rear Seat Seat Heaters SEAT HEATER To turn the power off, push the opposite side of the switch lightly. The lamp will go out. Follow these precautions whenever you use the seat heaters: Folding Rear Seat The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the car or inside the trunk. Use the HI setting only to heat the seats quickly. Select the LO setting when the seats feel warm. The HI setting draws large amounts of current from the battery. Do not use the seat heaters, even at a low setting, if the engine is left idling for an extended period. They can weaken the battery, causing hard starting. On Canadian models Both front seats are equipped with seat heaters. The ignition must be ON (II) to use them. Push the front of the switch to turn the power on at a high temperature setting, and the rear to set the heater at a low temperature. The HI or LO lamp lights and remains on while the heater is on. Instruments and Controls Main MenuTable of ContentsstMASTER KEY RELEASE To fold down the seat-back from inside the car, insert the master key in the lock on the rear shelf. Turn the key clockwise, pull down the top of the seat-back, then release the key. Pull To release the seat-back from inside the trunk, pull the release under the rear shelf. To lock the seat-back upright, push it firmly against the rear shelf. Make sure it is latched in place by pulling on the top of the seat. Folding Rear Seat Make sure both rear shoulder belts are positioned in front of the rear seat-back whenever the seat-back is in its upright position. Make sure all items in the trunk, or items extending through the opening into the back seat, are tied down. Loose items can fly forward and cause injury if you have to brake hard. See Loading Cargo on page 106. Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 25. Instruments and Controls Main MenuTable of ContentsstPower Windows Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window. Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it. Instruments and Controls Closing a power window on a child's hands or fingers can cause serious injury. Make sure your children are away from the windows before closing them. DRIVER'S WINDOW SWITCH MAIN SWITCH The driver's armrest has a master power window control panel. To open the passenger's window, push down on the switch and hold it down until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want. Main MenuTable of ContentsstThe master control panel also con- tains these extra features: AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, pull back on the window switch briefly. To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch. The AUTO function only works to lower the driver's window. To raise the window, you must pull back on the window switch and hold it until the window reaches the desired position. The MAIN switch controls power to the passenger's window. With this switch off, the passenger's window cannot be raised or lowered. The MAIN switch does not affect the driver's window. Keep the MAIN switch off when you have children in the car so they do not injure them- selves by operating the window unintentionally. The power window system has a key- off delay function. The windows will still operate for up to ten minutes after you turn off the ignition. Opening either door cancels the delay function. You must turn the ignition ON (II) again before you can raise or lower the windows. Power Windows Instruments and Controls Main MenuTable of ContentsstMoonroof The moonroof has a key-off delay. You can still open and close the moonroof for up to ten minutes after you turn off the ignition. The key-off delay cancels as soon as you open either door. You must then turn the ignition ON (II) for the moonroof to operate. NOTICE If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor. MOONROOF SWITCH Use the switch on the dashboard to open and close the moonroof. The ignition must be ON (II). Push and hold the switch to open the moonroof. Release the switch when the moonroof reaches the desired position. To close the moonroof, press and hold the switch. Closing the moonroof on someone's hands or fingers can cause serious injury. Make sure passengers are clear of the moonroof before closing it. Instruments and Controls Main MenuTable of ContentsstMirrors Adjusting the Power Mirrors SELECTOR SWITCH TAB Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position. Adjust the outside mirrors with the adjustment switch on the driver's door armrest: 3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up or down. 1. Turn the ignition switch ON (II). 2. Move the selector switch to L (driver's side) or R (passenger's side). 4. When you finish, move the selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping the switch. CONTINUED Instruments and Controls Main MenuTable of ContentsstMirrors, Parking Brake Parking Brake NOTICE HEATED MIRROR BUTTON PARKING BRAKE LEVER Driving the car with the parking brake applied can damage the rear brakes and axles. Available on all Canadian models The outside mirrors are heated to re- move fog and frost. With the ignition ON (II), turn on the heaters by pressing the button. The light in the button comes on as a reminder. Press the button again to turn the heaters off. To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 31). Instruments and Controls Main MenuTable of ContentsstHOUR MIN RESET To set the clock: 1. Turn the ignition switch ON (II) to display the time. 2. Swing down the front cover of the wide button under the clock display. You will see HOUR, MIN, and RESET buttons. Digital Clock You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing RESET sets the clock back to the previous hour. If the displayed time is after the half hour, pressing RESET sets the clock forward to the beginning of the next hour. The digital clock displays the time with the ignition switch ON (II). 3. Press and hold the HOUR button until the hour advances to the desired time. For example: 1:06 would RESET to 1:00. 1:52 would RESET to 2:00. 4. Press and hold the MIN button until the numbers advance to the desired time. Instruments and Controls Main MenuTable of ContentsstBeverage Holder PARTITION Be careful when you are using the beverage holder. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can also damage the upholstery, carpeting, and electrical components in the interior. The front beverage holder is located on the center console. The partition in the beverage holder can be moved forward or backward. If you want to use the beverage holder, slide the partition forward until it clicks. To put small items in the beverage holder, slide the partition completely backward. Use the beverage holder only when the car is parked. If you place cups in the holder while driving, the liquid may spill when you go over bumps or around corners. Instruments and Controls Main MenuTable of ContentsstBeverage Holder, Console Compartment Console Compartment LEVER LEVER The rear seat also has a beverage holder in the armrest on the driver's side. CONSOLE COMPART- MENT To open the console compartment, press the lower lever and lift the lid. To close, lower the lid and push it down until it latches. You can put small items in the tray located in the console compartment lid. To use the tray, press the upper lever and lift up the armrest pad. Instruments and Controls Main MenuTable of ContentsstCoin Box, Accessory Power Socket Coin Box Accessory Power Socket The coin box is located next to the beverage holder. Open the lid by lifting it up. To remove the coin box for emptying, lift the coin box up by pushing up on the middle edge of the coin box on the console guide. Never use the coin box for smoking materials. Instruments and Controls ACCESSORY POWER SOCKET To use the accessory power socket, pull down the cover. The ignition switch must be in ACCESSORY (I) or ON (II). This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps). It will not power an automotive type cigarette lighter element. Main MenuTable of ContentsstAshtrays (Optional) Front and rear ashtrays are available as options. The front ashtray fits In the coin box. The rear ashtray fits in the rear pocket on the rear seat armrest on the driver's side. Open the rear ashtray by lifting up the lid. To remove the ashtray for emptying, open the lid and then lift it up and out. NOTICE Use the ashtray only for cigarettes, cigars, and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray. Ceiling Lights DOOR ACTIVATED The ceiling light contains a main light as well as two spotlights. Ashtrays, Interior Lights The ceiling light has a three-position switch. In the OFF position, the light does not come on. In the center position, the ceiling light comes on when you open either door. After both doors are closed tightly, the light dims slightly, then fades out in about 10 seconds. In the ON position, the ceiling light stays on continuously. CONTINUED Instruments and Controls Main MenuTable of ContentsstInterior Lights Courtesy Lights Turn on the spotlight by pushing the button next to each light. Push the button again to turn it off. You can use the spotlights at all times. Your car has a courtesy light in the ignition switch. The ignition switch light comes on whenever you open either door. It remains on, then fades out in about 10 seconds after both doors are closed tightly. The ignition switch light and ceiling light (with the switch in the center position) also comes on when you unlock the door with the key, the lock tab on the driver's door, or the Instruments and Controls master door lock switch. If you relock the driver's door or close the driver's door with the key in the ignition switch, the lights turns off immediately. Otherwise, the light remains on, then fades out in about 10 seconds. If you keep the door open, the ceiling light (with the switch in the center position) will turn off after three minutes when the key is not in the ignition switch. On Type SH Your car also has a courtesy light in each door. Each door light comes on when the door is opened, and goes out when the door is closed tightly. Main MenuTable of ContentsstComfort and Convenience Features The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions. The standard audio system has many features. This section de- scribes those features and how to use them. (If you selected an optional audio system, refer to the operating instructions that came with it.) Your Honda has an anti-theft audio system that requires a code number to enable it. Heating and Cooling........................ 70 What Each Control Does............ 70 How to Use the System............... 72 To Turn Everything Off............. 77 Audio System................................... 78 AM/FM/CD Audio System....... 78 Operating the Radio.................... 79 Adjusting the Sound.................... 82 Audio System Lighting............... 83 Radio Frequencies....................... 83 Radio Reception.....,...,...,..,..,,...... 83 Operating the CD Player............ 85 Operating the CD Changer........ 87 Protecting Compact Discs.......... 88 CD Player Error Indications....... 89 CD Changer Error Indications... 90 Operating the Cassette Player... 91 Tape Search Functions............... 92 Caring for the Cassette Player... 94 Theft Protection........................... 95 Comfort and Convenience Features Main MenustHeating and Cooling Proper use of the Heating and Cooling system can make the interior dry and comfortable, and keep the windows clear for best visibility. What Each Control Does Fan Control Lever Sliding this lever to the right increases the fan's speed, which increases air flow. Temperature Control Lever Sliding this lever to the right increases the temperature of the air flow. Air Conditioning (A/C) Button This button turns the air condi- tioning ON and OFF. The indicator in the button lights when the A/C is on. Comfort and Convenience Features MODE BUTTONS REAR WINDOW DEFOGGER BUTTON RECIRCULATION BUTTON TEMPERATURE CONTROL LEVER Rear Window Defogger Button This button turns the rear window defogger on and off (see page 41). AIR CONDITIONING BUTTON FAN CONTROL LEVER Recirculation Button This button controls the source of the air going into the system. When the indicator in this button is lit, air from the vehicle's interior is sent through the system again (Recircula- tion mode). When the indicator is off, air is brought in from outside the vehicle (Fresh Air mode). Main MenuTable of ContentsstMode Buttons Use the MODE buttons to select the vents the air flows from. Air flows from the center and corner vents in the dashboard. Air flow is divided between the vents in the dashboard and the floor vents. Air flows from the floor vents. Air flow is divided between the floor vents and the defroster vents at the base of the windshield. Air flows from the defroster vents at the base of the windshield. When you select automatically switches to Fresh Air mode and turns on the A/C. the system Heating and Cooling Comfort and Convenience Features Main MenuTable of ContentsstHeating and Cooling Vent Controls CENTER VENT SIDE VENT You can adjust the direction of the air coming from the dashboard vents by moving the tab in the center of each vent up-and-down and side-to- side. The vents in the corners of the dashboard can be opened and closed with the dials underneath them. Comfort and Convenience Features How to Use the System This section covers how to set up the system controls for ventilation, heating, cooling, dehumidifying, and defrosting. The engine must be running for the heater and air conditioning to generate hot and cold air. 'The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system. The air conditioning does not rely on engine temperature. Main MenuTable of ContentsstIt Is best to leave the system in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up. Switch to Recirculation mode when you are driving through smoky or dusty conditions, then switch back to Fresh Air mode when the condition clears. The outside air intakes for the heating and cooling system are at the base of the windshield. Keep these clear of leaves and other debris. Heating and Cooling MODE BUTTONS RECIRCULATION BUTTON TEMPERATURE CONTROL LEVER Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear window. FAN CONTROL LEVER 1. Slide the temperature control lever AIR CONDITIONING BUTTON all the way to the left. Make sure the A/C is off. 2. Select 3. Set the fan to the desired speed. and Fresh Air mode. CONTINUED Comfort and Convenience Features Main MenuTable of ContentsstMODE BUTTONS RECIRCULATION BUTTON TEMPERATURE CONTROL LEVER FAN CONTROL LEVER AIR CONDITIONING BUTTON Heating and Cooling To Cool with A/C 1. Turn on the A/C by pressing the button. The light in the button should come on. 2. Make sure the temperature control lever is all the way to the left. 3. Select and Fresh Air mode. 4. Set the fan to the desired speed. Comfort and Convenience Features Main MenuTable of ContentsstIf the interior is very warm from being parked in the sun, you can cool it down more rapidly by setting up the controls this way: 1. Start the engine. 2. Turn on the A/C by pressing the button. Make sure the tempera- ture control lever is all the way to the left. 3. Set the fan to maximum speed. 4. Open the windows partially. Select and Recirculation mode. When the interior has cooled down to a more comfortable temperature, close the windows and set the controls as described for normal cooling. Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 35) when driving in stop-and-go traffic or climbing a long, steep hill. If it moves near the red zone, turn off the A/C until the gauge reads normally. To Heat To warm the interior: 1. Start the engine. 2. Select 3. Set the fan to the desired speed. 4. Adjust the warmth of the air with and Fresh Air mode. the temperature control lever. Heating and Cooling To Heat and Dehumidify with Air Conditioning Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry. 1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control and Fresh Air mode. lever so the mixture of heated and cooled air feels comfortable. This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C). CONTINUED Comfort and Convenience Features Main MenuTable of ContentsstHeating and Cooling To Defog and Defrost To remove fog from the inside of the windows: 1. Switch the fan on. 2. Select When you select system automatically switches to Fresh Air mode and turns on the A/C. the 3. Adjust the temperature control lever so the air flow from the defroster vents feels warm. 4. Turn on the rear window defogger to help clear the rear window. 'When you switch to another mode from Press the A/C button to turn if off. the A/C stays on. Comfort and Convenience Features MODE BUTTONS REAR WINDOW DEFOGGER BUTTON RECIRCULATION BUTTON TEMPERATURE CONTROL LEVER FAN CONTROL LEVER AIR CONDITIONING BUTTON Main MenuTable of ContentsstTo remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather: 1. Start the engine. 2. Select When you select system automatically switches to Fresh Air mode and turns on the A/C. the 3. Switch the fan and temperature controls to maximum. To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows. Heating and Cooling These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get warmer and clear the windows faster as the engine warms up. You can close the side vents with the dial underneath each vent. This will send more warm air to the windshield defroster vents. For safety, make sure you have a clear view through all the windows before driving away. To Turn Everything Off To shut off the system temporarily, slide the fan speed and temperature control levers all the way to the left, You should shut the system completely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior. Comfort and Convenience Features Main MenuTable of ContentsstAM/FM 1-2 BUTTON TUNE BAR PWR/VOL KNOB PRESET BUTTONS SEEK BAR Audio System AM/FM/CD Audio System Your Honda's audio system provides clear reception on both AM and FM bands, while the preset buttons allow you to easily select your favorite stations. The Anti-theft feature will disable the system if it is disconnected from the car's battery. To get the system working again, you must enter a code number (see page 95 ). Comfort and Convenience Features Main MenuTable of ContentsstOperating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob. Adjust the volume by turning the same knob. The band and frequency that the radio was last tuned to is displayed. To change bands, press the A M / FM 1-2 button. On the FM band, ST will be displayed if the station is broad- casting in stereo. Stereo reproduc- tion on AM is not available. You can use any of three methods to find radio stations on the selected band: TUNE, SEEK, or the Preset buttons. TUNE — Use the TUNE bar to tune the radio to a desired frequency. Press the to a higher frequency, and the side of the bar to tune side to tune to a lower frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly. Audio System SEEK — The SEEK function searches the band for a station with a strong signal. To activate it, press or the SEEK bar on either the side, then release it. Depending on which side you press, the system scans upward or down- ward from the current frequency. It stops when it finds a station with a strong signal. Preset — You can store the fre- quencies of your favorite radio stations in the six preset buttons. Each button will store one frequency on the AM band, and two on the FM band. CONTINUED Comfort and Convenience Features Main MenuTable of ContentsstAM/FM 1-2 BUTTON TUNE BAR PRESET BUTTONS SEEK BAR Audio System To store a frequency: 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each Preset button. 2. Use the TUNE or SEEK function to tune the radio to a desired station. 3. Pick the Preset button you want for that station. Press the button and hold it until you hear a beep. 4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM. Once a station's frequency is stored, simply press and release the proper Preset button to tune to it. The preset frequencies will be lost if your vehicle's battery goes dead, is disconnected or the radio fuse is removed. Comfort and Convenience Features Main MenuTable of ContentsstAUTO SELECT — If you are traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area. To activate Auto Select, press the A. SEL/RPT button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals. It stores the frequen- cies of six AM stations and twelve FM stations in the preset buttons. You can then use the preset buttons to select those stations. If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a "0" displayed when you press any preset button that does not have a station stored. Audio System TUNE BAR SEEK BAR PRESET BUTTONS AUTO SELECT/ REPEAT BUTTON With Auto Select on, you cannot manually store any frequencies in the preset buttons. If you do not like the stations found by Auto Select, you can use the TUNE and SEEK functions to find other stations. Auto Select does not erase the frequencies that you preset pre- viously. When you return home, turn off Auto Select by pressing the A. SEL/RPT button. The preset buttons will then select the fre- quencies you originally set. Comfort and Convenience Features Main MenuTable of ContentsstAudio System Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the MODE button several times. The selected mode, BAS, TRE, FAD, or BAL is shown in the display. Balance/Fader — These two modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength. Select BAL or FAD by pressing the MODE button. Adjust the Balance or Fader to your liking by turning the PWR/VOL knob. The number in the display (from — 9 to 9) shows you the current setting. Comfort and Convenience Features

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

1997 Honda Prelude Owners Manual