1990 Honda Civic Wagon Owners Manual

to

In fog or very light rain, push the lever down to the MIST position t e m p o r a ry high s p e ed f or operation of the wipers. The wipers will return to the "rest" position and the motor will shut off as soon as you release the lever.

Push down

Windshield Washer Pull the wiper switch lever toward you to turn on the washer. Check the washer fluid regularly, especially during bad weather or whenever the washer has been in frequent use.

WASHER FLUID RESERVOIR

PULL

Use a good quality commercial washer fluid for all-weather cleaning.

CAUTION:

Do not use radiator antifreeze in the windshield washer; it will damage the paint. Do not use a vinegar/water combination in the windshield washer; it will damage the pump. Prolonged operation of the washer without fluid may damage the pump.

freezing weather, warm

the defrosters In before using the washer. This will help prevent icing which could seriously impair visibility.

the windshield with

WINDSHIELD WASHER RESERVOIR CAPACITY: 2.5

(2.6 US qt, 2.2 Imp qt)

(cont'd)

Main MenustWindshield Wipers/Washer/Defogger (cont'd)

Rear Window Wiper/Washer Switch to " O N" to activate the rear wiper. Turn and hold the switch one more step clockwise to " to activate the washer and wiper; or turn and hold the switch one step counterclockwise from "OFF" to activate to washer only. The rear w a s h er uses fluid t he same reservoir as the front washer.

WIPER

WASHER

the switch

Rear Window Defogger Push the to defogger on or off. The indicator will light when the defogger is on. The defogger will turn off automatically 24 minutes after it is turned on.

turn

CAUTION: When cleaning the inside of the rear window, be careful not to damage the printed heater wires on the rear window. Wipe the window horizontally along the wires, not up and down.

Main MenustParking Brake and Mirrors

Parking Brake To apply the parking brake, pull up on the lever. To release it, pull up slightly, push the button, and lower the lever; when fully released, the BRAKE warning light will go out.

Pull up

Rearview Mirrors Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust mirrors before you start. The outside mirror can be adjusted by moving the knob on the inside of the driver's door.

DAY/NIGHT ADJUSTMENT TAB

ADJUSTMENT KNOB

The inside mirror has day and night positions. The night position reduces glare from the headlights of vehicles behind you. Flip the small tab on the bottom of the mirror forward or backward to select day or night position.

Main MenustLights

FIRST STOP

RIGHT TURN

Turn Signals Push the turn signal lever down to signal a left turn, and up for a indicator and right turn. The lights will appropriate signal lever will return blink. The automatically its original position when the steering wheel is returned to straight ahead. For lane changing, you can signal by pushing the lever part way up or down (to the first stop) and holding it there; the lever will return to its original position when you release it. If either turn signal indicator lights up but does not blink, blinks faster than usual, or does not light up at all, check for a burned out bulb or fuse.

FIRST STOP

LEFT TURN

to

Turn

FIRST POSITION

SECOND POSITION

Pull and release

Headlights light switch to the Turn the first position ( ) for taillights, lights, position side marker lights, license plate lights, and instrument panel lights. Turn to the second position ( ) to add the headlights.

High Beam/Low Beam Switch T he h e a d l i g h ts m ay be switched between low beam and high beam by pulling the turn signal lever towards you until a click is felt. The blue high beam indicator light will be on when the high beam is on.

Headlight Flasher To use the headlights as a passing signal, pull lightly on the turn signal lever and release.

Main MenustHazard Warning System This system should be used only when your car is stopped under emergency or hazardous conditions. the hazard To activate warning switch . The front and rear simultaneously and both indicator lights will flash. Push the switch again to turn the system off.

t u rn s i g n a ls w i ll b l i nk

push

Panel Brightness Control When the light switch is in either of the the intensity of lights can be adjusted by turning the panel brightness control dial.

two " O N" positions, instrument

the

light has a

Interior Light three The interior position switch. The light is off all the time in the OFF position. In the middle position, it goes on only when a door is opened. In the ON position, it is on all the time.

Push

ON

OFF

DOOR ACTIVATED

(cont'd)

Main MenustLights (cont'd)

Luggage Area Light The luggage area light has a two-position switch. In the first position it is OFF all the time, in the second position it goes ON only when the tailgate is opened.

Main MenustHood and Glove Box

Hood To open, pull back on the handle under the left side of the dash.

Pull to release

The hood latch is spring-loaded, so the hood will pop up slightly. Release the safety catch under the front center of the hood by pushing the rubber-tipped handle up. Lift the hood and prop it open with the support rod. To close, take the support rod down, and return it to its clip, then lower the hood until it is approximately one foot from the closed position, then let it drop. Be sure the hood is securely latched before driving away.

SUPPORT ROD

Push

Glove Box Open by pushing the knob as shown. Close with a firm push.

Do not drive the car with the glove box door open; it could cause injury in an accident.

Main MenustCigarette Lighter and Ashtrays

Cigarette Lighter Push in to heat up. It will automati- cally release when the element is hot. DO NOT hold it in while it is heating up.

Push

its

the ashtray by pulling

Front Ashtray Open bottom edge toward you. further To remove while pushing down on the spring loaded plate inside. To install, procedure.

reverse

it, pull

it out

removal

the

PLATE

Rear Ashtray Open the ashtray by pulling its top edge. To remove it, open the ashtray and release its bottom edge by pulling up, then out. To install, reverse the removal procedure.

To remove, pull up and out

CAUTION: Do not use the ashtrays as trash containers; use them only for extinguished cigarettes. Putting lit cigarettes or matches in an ashtray with other combustible materials may cause a fire.

Main MenustClock

Digital Clock The time is displayed continuously when the ignition is on. At all other times, push in on the lid to display the time. To adjust the time: 1. Lower the lid. 2. Push the minute button (MIN) and hold it until the numbers advance to the desired minutes.

3. Push the hour button (HOUR) and hold it until the numbers advance to the desired hour.

LID

4. The RESET button allows you to synchronize your clock to the closest hour. If the time on the clock is before the half hour, pressing the RESET button will return the time to the previous hour. If the time is beyond the half hour, the RESET button will change the time to the next hour.

NOTE: Be careful not to push the HOUR, MIN or RESET buttons accidentally. Pushing any of them will change the clock's time setting.

Main MenustHeating and Cooling

The vents, heater and air conditioner are combined in one system; adjusting four basic controls to different settings can provide a full range of interior temperatures for safe and comfortable driving. Airconditioner: optional

Ventilation The flow-through ventilation system can provide fresh air to the interior when the car is moving or stopped, even with the windows closed.

NOTE: For proper air flow, the flow-through vents must not be covered. Keep the air inlet at the base of the windshield free of leaves or other debris.

AIR OUTLET

AIR INLET

You can adjust the controls to direct cool or warm outside air throughout the car for defogging windows, heating, or cooling. When stopped or driving at low speeds, you can increase the air flow by turning on the fan.

Main MenustDash Vents The corner vents can be used for flow-through ventilation, or for heating and air conditioning: When the car is moving, the driver's corner vent can also route fresh air directly from the outside by sliding the corner vent lever below it to the right and shutting it off from the heater and air conditioner system. The louvers in the corner and center vents can be tilted up or down and right or left, to change the direction of air flow.

SIDE DEFROSTER OUTLET

WINDSHIELD DEFROSTER OUTLETS

CORNER VENT

CORNER VENT LEVER

FRONT FLOOR OUTLETS

REAR FLOOR OUTLETS

CENTER VENTS

CORNER VENT

(cont'd)

Main MenustHeating and Cooling (cont'd)

What the Controls Do:

TEMPERATURE CONTROL DIAL

RECIRCULATION SWITCH LEVER

FUNCTION LEVER

FAN SWITCH

AIR CONDITIONER AND INDICATOR LIGHT(optional)

Fan Switch Switch the fan to low (1), medium (2), medium high (3) or high (4) speed, to circulate warm, cool, or outside air, depending on where the temperature control dial and function lever are set. Whenever the fan is switched on, air flows from the dash corner vents regardless of function selection.

Function Lever Slide the lever right or left to direct outside air or recirculated (inside) air to and from the heater, air conditioner and vents.

Temperature Control Dial Turn the dial clockwise to make air warmer when the appropriate function is selected. Air Conditioner Switch With the fan on, push the A/C switch to operate the air conditioner; the indicator light will come on. Push the switch again to turn the air conditioner off.

(optional)

Recirculation Lever When the lever is set at the a l l o w ed to c i r c u l a te inside t he car. W h en t he lever is set at

position, outside air will be

position, outside air is shut off and the air inside the car is recirculated. So when the heater or air conditioner is on and you want to warm up or cool down the interior more quickly, or keep smoke or dust out of the car without losing the heat or cool function, simply set the lever to the

position.

Main MenustNOTE: The w i n d o ws may b e c o me fogged if t he s y s t em is in t he

position for an extended period of time with the air conditioner off. As soon as the interior is warmed, slide the lever to the

position.

How to Use the Controls

To Ventilate Turn the temperature control dial counterclockwise, slide the recirculation lever to the position and the function lever to the position. Switch the fan on and outside air will flow through the corner and center vents. To change air distribution, slide the function lever to the position, and outside air will also flow from the floor level outlet at the heater.

To Cool (with optional air conditioner) To cool the car down quickly, slide the recirculation lever to the position, start the engine, turn the temperature control dial counterclockwise all the way, switch the fan to high ( 4 ), push the A/C button in, and open the window briefly. Then close the windows and corner vents, slide the function lever to t he

p o s i t i on and the r e c i r c u l a t i on lever to t he

position so inside air will recirculate to the air conditioner

for maximum cooling.

When the interior has cooled sufficiently, switch the fan to low (1), medium (2) or medium high (3), then slide the recirculation lever to the the air conditioner.

(outside) air

to direct

position

fresh

to

(cont'd)

Main MenustHeating and Cooling (cont'd)

When using the air conditioner in heavy traffic, or while driving up long hills, watch the coolant temperature gauge: if the needle moves near the " H" end of the scale, turn the air conditioner off by pushing the A/C button; leave it off until the needle goes back well into the middle of the scale.

To Heat Switch the fan on, turn the temperature control dial clockwise, slide the function lever to the position and the recirculation lever to the position, and warmed (outside) air will begin flowing from the floor outlets.

To warm up the interior quickly, slide the recirculation lever to the

position so inside air will recirculate to the heater.

The w i n d o ws may b e c o me f o g g ed if t he s y s t em is in t he

position for an extended period of time. As soon as the

interior is warmed, slide the lever to the

position.

To Dehumidify (with optional air conditioner) Because an air conditioner dehumidifies as it works, you can use it in cool or cold weather in any function position to help defog the windows. Just switch the fan on, push the A/C button on, set either the positions, and adjust the temperature control dial to a comfortable setting.

or

NOTE: This setting is desirable for most operating conditions in ambient temperatures above approximately 32°F (0°C).

Main MenustTo Defrost To defrost or defog the windshield and door windows, turn the temperature control dial clockwise, slide the function lever to the (defrost) position, the recirculation lever to the position, and switch the fan on. Warmed (outside) air will then flow from the windshield and side defroster vents. Use the

position only.

To Turn Everything OFF Slide all levers to the counterclockwise all the way, and push the A/C switch off.

left, turn the temperature control dial

NOTE: This setting should only be used in cold weather for the first few minutes of driving to prevent cold air from blowing into the cabin. Under normal operating conditions, the fan should always be kept ON to prevent the accumulation of stale air in the system.

Main MenustGasoline

For proper operation of your car's emission controls, your engine is designed to use unleaded fuel only.

CAUTION: Using leaded or even low-lead gasoline could damage some of your emission controls, and also void their coverage under the emission controls warranty.

Use gasoline from pumps labeled unleaded, with a pump octane number of 86 or higher. The pump octane number is an average of the Research (R) octane and Motor (M) octane numbers. Use of a lower octane gasoline can cause persistent, heavy "SPARK KNOCK" (a metallic rapping noise), which can lead to engine damage if severe.

CAUTION: If you notice steady spark knock while holding a steady speed on a level road, try changing brands of gasoline. If the spark knock persists, consult your Honda dealer. Failure to do so is considered misuse, and misuse is not covered under the New Car Warranty.

Occasionally you may notice light spark knock while accelerating or driving up hills. This is no cause for concern, it simply means your engine is running at its most economical.

Gasoline Containing Alcohol If you decide to use a gasoline containing alcohol ("gasohol"), be sure its octane rating is at least as high as that recommended for unleaded gasoline. There are that containing ethanol, and that containing methanol. Do not use gasohol that contains more than 10% ethanol. Do not use gasoline containing methanol (methyl or wood alcohol) that does not also contain cosolvents and corrosion inhibitors for methanol. Never use gasoline containing more it has cosolvents and corrosion inhibitors.

than 5% methanol, even

"gasohol":

types of

two

if

Main MenustNOTE:

Fuel system damage or vehicle performance problems resulting from the use of such fuels is not covered under the new car warranties. Honda cannot endorse the use of fuels containing methanol since evidence of their suitability is as yet incomplete. Before purchasing fuel from an unfamiliar station, try to confirm whether the fuel contains alcohol; of what kind, and how much. If you notice any undesirable operating symptoms after using a gasoline that contains alcohol, or one that you think contains alcohol, switch to an unleaded gasoline, as recommended on page 40.

Operation In Foreign Countries In order to comply with U.S. Federal Emissions Regulations, you must use unleaded fuels of the recommended octane rating. These fuels may not be available in other countries. If you intend taking your car outside the U.S. or Canada, write to American Honda Consumer Affairs (stating the year and model of your car) at the address below for information regarding modifications you may need to have done.

American Honda Motor Co., Inc. Consumer Affairs 100 W. AIondra Blvd., Gardena, CA 90248

Fuel Filler Door and Cap

Gasoline is extremely flammable and is explosive under certain conditions. Perform this operation in a well-ventilated area with the engine stopped. Do not smoke or allow open flames or sparks in the area or where gasoline is stored.

The fuel filler door is opened by pulling up on the lever at the left side of the driver's seat. The door will lock automatically when closed; push it until it clicks.

CAUTION: You may hear a hiss when you open the filler cap. This sound is residual pressure escaping from the fuel tank. Open the cap slowly and remove the cap after the hissing stops. Fuel spray may cause injury. Do not overfill the tank; fill only until the gas pump clicks off automatically and never top off.

(cont'd)

Main MenustGasoline (cont'd)

Open

Close

Fuel vapor is extremely hazardous under certain conditions. Always stop the engine before refueling, and never refuel near sparks or open flames.

CAUTION: When reinstalling the fuel cap, be sure both tabs on the cap are engaged in the slots of the filler neck and turn the cap until it stops. If you replace the cap, use only a genuine Honda replacement part or its equivalent. Failure to use the proper part could cause serious fuel system problems.

How to Improve Your Gas Mileage:

Drive at a smooth, steady pace to avoid unnecessary decelerations and stops — accelerating back to speed uses more fuel. Plan trips to avoid rush hour traffic if possible. Make sure the parking brake is completely released. Consolidate trips whenever possible. Keep vehicle weight to a minimum by removing unnecessary items from the luggage area. Whenever possible, use fresh air from the dash vents to keep cool when driving; open windows or use of the optional air conditioning both affect fuel economy. Keep the tires adjusted to the recommended pressure. Tire Pressure (measured cold):

Front/Rear

CIVIC WAGON 4WD

220/220 kPa (32/32 psi) 195/195 kPa (28/28 psi)

Condition of Your Car You can only get maximum fuel economy if your car is in top running condition. Have all required maintenance done at the proper intervals. Check tire pressures and tire wear frequently. If tire wear is uneven, have the alignment checked by your Honda dealer. Proper alignment saves gasoline and prolongs tire life.

Main MenustIgnition Switch

The combined ignition switch/anti-theft lock is located on the right side of the steering column and has four positions:

0-LOCK position: The key can be removed or inserted in this position. To remove the key, push it in at position I, then turn it to 0 and pull it out. When the key is removed, the steering column will lock.

NOTE: On cars equipped with automatic transmissions, the transmission must be in Park before pushing and turning the key to the 0-LOCK position.

Never turn the ignition switch to the lock position or remove the key while the car is in motion; the steering wheel can lock causing a loss of directional control, and an accident could result.

I-ACCESSORY position: In this position, the accessory circuit is on, but the ignition circuit is off. If the key is difficult to turn from the 0 to the I position, turn the steering wheel slightly to relieve pressure on the lock.

II-ON position: This is the normal running position.

III-START position: The starter will engage when the key is turned to this position.

To remind you to remove the ignition key when leaving your car, a beeper will sound if the key is still in the ignition when you open the driver's door. The beeper system is deactivated when you turn the ignition to 0 (Lock) and fully remove the key.

Main MenustStarting the Engine

Before Starting

Manual Transmission: 1. Apply the parking brake. 2. Push the clutch pedal all the way in (see NOTE below). 3. Shift the transmission to neutral.

NOTE: On cars equipped with manual transmissions, the engine will not crank unless the clutch pedal is fully depressed.

Automatic Transmission: 1. Make sure the shift lever is in Park (P). 2. Apply the parking brake and the foot brake.

NOTE:

When starting in cold weather, keep all unnecessary electrical circuits off (lights, defogger, etc.) for the best battery output. Do not crank the engine for more than 15 seconds at a time. Wait 10 seconds before going to the next step.

Starting the Engine: 1.With YOUR FOOT OFF THE ACCELERATOR start the engine by

turning the key to the III position.

2. If the engine won't start within 15 seconds or starts but fails to continue to run, push the accelerator pedal halfway, and hold it there while cranking the engine. Once the engine starts, release the accelerator gradually as the engine speeds up.

3. If it doesn't start within 15 seconds, push the accelerator pedal down to the floor and hold it there while cranking in order to clear flooding. Try step 2 again.

Cold Weather at High Altitude Starting: 1. When starting in cold weather at high altitude (above 8,000 feet), push the accelerator pedal about halfway and hold it there while cranking the accelerator gradually as the engine speeds up.

the engine starts,

the engine. Once

release

2. If it doesn't start within 15 seconds, push the accelerator pedal down to the floor and hold it there while cranking in order to clear flooding. Try step 1 again.

NOTE: If the outside temperature is below freezing, or if your car has not been driven for several days, warm up the engine for a few minutes before driving.

Main MenustSafety Items

Before driving away, check that: The doors are closed properly. The mirrors are properly adjusted, and the windows clean. The driver and passengers are wearing properly adjusted seat belts. The head restraints are properly adjusted. The warning and indicator lights are operating properly. The brake pedal feels normal. All luggage and cargo is secured. Nothing is interfering with the driver's feet or blocking vision to the rear.

While driving remember to:

Always drive defensively; expect the unexpected. Reduce your speed during night hours and bad weather. Follow at a safe distance; don't tailgate. Get off the highway when you are tired; stop and take a rest.

When stopping for repairs:

Park the car well off the road. Turn on the hazard warning flasher. Use flares or other warning devices to warn other motorists.

After parking your car:

transmission, or PARK on automatic

Apply the parking brake and shift to first gear if equipped with manual transmission equipped cars. Take your keys. Make sure the windows are closed and all doors are locked. If parked on a hill:

1. Turn the front wheels away from the curb if facing uphill. 2. Turn the front wheels toward the curb if facing downhill.

Never leave children unattended in a parked car.

Main MenustEngine Exhaust Gas Warning

A properly maintained car is your best protection against exhaust gas entering the passenger compartment. The exhaust system should be competent mechanic whenever:

inspected by a

thoroughly

The car is raised for an oil change. You notice a change in the sound of the exhaust. The exhaust system or the rear or underside of the car is damaged.

• Avoid breathing exhaust gases. They contain carbon monoxide, which is a colorless, odorless gas that can cause loss of consciousness and eventual death. If you suspect that exhaust gas is entering the passenger compartment, have the cause determined and corrected as soon as possible. If you must drive under these conditions, drive only with all windows fully open. Do not drive with the tailgate open. An open tailgate may draw exhaust gases into the passenger compartment. If you must drive with the tailgate open, drive only with all the windows wide open. Do not run the engine in confined areas, such as garages, any longer than necessary to move the car in or out. If you must sit in a parked car with the engine running for more than a short time, adjust the heating/ventilation system as follows:

1. Set the function lever to the 2. Set the temperature control dial for best comfort. 3. Set the recirculation lever to the position. 4. Turn the fan to the highest speed.

position.

NOTE: To insure proper operation of the car's ventilation system, keep the front air inlet clear of snow, mud, leaves or other obstructions.

Main MenustShifting the 5 or 6 Speed

The fully synchronized manual transmission is very easy to shift up or down. When you slow down for traffic, steep hills, or corners, shift to a lower gear before the engine starts to labor. When descending steep grades, select a lower gear to help maintain a safe speed and to prevent the brakes from overheating. When shifting, depress the clutch pedal fully, shift gears and then release the clutch gradually. Do not speed-shift; allow time for the gears to synchronize. To prevent grinding the gears when shifting into reverse, hold the clutch pedal depressed briefly before shifting, or shift the lever into one of the forward gears before selecting reverse. A safety lockout prevents accidental shifting straight from 5th to Reverse.

5 Speeds (CIVIC WAGON)

6 Speeds (4WD)

SL-Super Low Gear (4WD) This super low ratio gear reduces the possibility of spinning the wheels when accelerating on roads covered with snow, sand or mud, or on steep hills.

Avoid rapid acceleration or sudden deceleration when either or both driving wheels are on a slippery surface. Decreased traction could cause loss of directional control.

CAUTION: When downshifting to SL, do so only at speeds of 3 mph (5km/h) or less and release the clutch gradually to avoid any sudden engine over-revving.

(cont'd)

Main MenustShifting the 5 or 6 Speed (cont'd)

free

Clutch Pedal Adjustment Clutch pedal to compensate for lining wear. There should be approximately 25 mm in) of pedal free travel. If not, or if the clutch seems to slip or the clutch

you have difficulty shifting, have your dealer check adjustment.

travel must be adjusted periodically

(1

CAUTION:

Do not drive with your foot on the clutch pedal as this will cause premature wear of clutch components. Do not shift into reverse while the car is moving. Driving with the clutch pedal free travel improperly adjusted can cause premature wear of the clutch components.

Maximum Allowable Speeds The speeds shown below are the maximum at which the car can be driven or downshifted in each gear without over-revving the engine:

CIVIC WAGON

4WD

Main MenustRecommended Shift Speeds For best fuel economy, and effective emission control, shift at the speeds shown for your car:

CIVIC WAGON

4WD

Main MenustShifting the Automatic (CIVIC WAGON)

The automatic transmission shift lever has a locking mechanism to prevent accidental shifting into Reverse (R), Park (P) or 2nd (2). Also, the Automatic Shift Lock prevents you from shifting out of Park unless the brake pedal is already depressed and the ignition switch is in the II position. Push the button on the shift handle to shift into 2nd, Reverse or Park; depress the brake pedal and then push the button on the shift handle to shift out of Park.

Depress button

: Depress the brake pedal first and push the button, then shift.

: Push the button, then shift. : Shift as desired.

If you cannot shift out of Park with the brake pedal depressed and the ignition switch in the II position: 1.Turn the ignition switch off and

remove the key.

2. Insert the key in the Shift Lock Release located to the right of the shift lever.

3. Press and hold the key down, then press the button on the shift handle and move the shift lever to Neutral. 4. Return

ignition switch, depress the brake pedal and restart the engine.

the key

the

to

KEY

Insert

SHIFT LOCK RELEASE

NOTE: If you encounter any problem shifting out of Park, have your authorized Honda dealer check the system as soon as possible.

ststMain MenuOperating Tips For smoother operation, apply the brakes when shifting from Neutral or Park to a forward or reverse gear. When parking: bring the car to a stop with the foot brake, hold the brake on and shift into Park, set the hand brake and then turn off the engine.

NOTE: Your 4 speed automatic transmission is equipped with a torque converter lock-up clutch. Because of this, you may notice what feels like an extra shift as the clutch engages.

CAUTION:

Shift into P only after the car has come to a complete stop. Shift into or out of R only after the car has come to a complete stop. Do not "rev-up" the engine when the brake is on and the shift lever is in D4, S3, 2 or R. When stopped on a hill, use the brakes to hold your position, not the accelerator pedal. Do not shift from N or P into D4, S3, 2 or R when the engine is above idle speed. Before shifting into gear, make sure your foot is firmly on the brake pedal. Do not rest your hand on the shift lever or push the shift button while driving.

(cont'd)

Main MenustShifting the Automatic (CIVIC WAGON) (cont'd)

Driving Technique

D4-4th Use the D4 range for normal in-town and highway driving. The car will start off in 1st and shift automatically to 2nd, 3rd, and 4th. The further down you push the accelerator, the later the transmission will shift and the faster the car will accelerate.

D3-3rd Use of D will allow the transmission to start off in 1st and shift automatically to 2nd and 3rd. Use D 3 when climbing grades to prevent the transmission from "hunting" between 3rd and 4th gear; or when increased braking is needed.

NOTE: If rapid acceleration is necessary, depress the accelerator to the floor; the transmission will automatically shift down according to load and engine speed. This applies to both D 4 and D3 ranges.

2-2nd Use 2nd gear for increased engine braking when driving downhill, and increased power when driving uphill; also for driving on slippery roads, and freeing the car from mud or sand, where 1st gear could provide too much power and cause skidding or wheel-spin. The maximum recommended speed in 2nd gear is: 62 mph (100 km/h)

R-Reverse

CAUTION: Shift into or out of reverse only after the car has come to a complete stop; the transmission may be damaged if you shift while the car is moving.

P-Park

CAUTION: Use this position when starting the engine, or when parking. Shift into Park only when the car is COMPLETELY stopped.

N-Neutral Use when starting the engine or during prolonged idling in traffic.

Main MenustShifting the Automatic (4WD)

The automatic transmission shift lever has a locking mechanism to prevent accidental shifting into Reverse (R), Park (P) or 2nd (2). Also, the Automatic Shift Lock prevents you from shifting out of Park unless the brake pedal is already depressed and the ignition switch is in the II position. Push the button on the shift handle to shift into 2nd, Reverse or Park; depress the brake pedal and then push the button on the shift handle to shift out of Park.

Depress button

: Depress the brake pedal first and push the button, then shift.

: Push the button, then shift. : Shift as desired.

If you cannot shift out of Park with the brake pedal depressed and the ignition switch in the II position: 1.Turn the ignition switch off and

remove the key.

2. Insert the key in the Shift Lock Release located to the right of the shift lever.

3. Press and hold the key down, then press the button on the shift handle and move the shift lever to Neutral. 4. Return

ignition switch, depress the brake pedal and restart the engine.

the key to the

KEY

Insert

SHIFT LOCK RELEASE

NOTE: If you encounter any problem shifting out of Park, have your authorized Honda dealer check the system as soon as possible.

stMain MenuShifting the Automatic (4WD) (cont'd)

Operating Tips For smoother operation, apply the brakes when shifting from Neutral or Park to a forward or reverse gear. When parking: bring the car to a stop with the foot brake, hold the brake on and shift into Park, set the hand brake and then turn off the engine.

NOTE: Your 4 speed automatic transmission is equipped with a torque converter lock-up clutch. Because of this, you may notice what feels like an extra shift as the clutch engages.

CAUTION:

Shift into P only after the car has come to a complete stop. Shift into or out of R only after the car has come to a complete stop. Do not "rev-up" the engine when the brake is on and the shift lever is in D, S, 2 or R. When stopped on a hill, use the brakes to hold your position, not the accelerator pedal. Do not shift from N or P into D, S, 2 or R when the engine is above idle speed. Before shifting into gear, make sure your foot is firmly on the brake pedal. Do not rest your hand on the shift lever or push the shift button while driving.

Main MenustDriving Technique

D-4th Use the D range for normal in-town and highway driving. The car will start off in 1st and shift automatically to 2nd, 3rd, and 4th. The further down you push the accelerator, the later the transmission will shift and the faster the car will accelerate.

S(S 3 — 3rd/S4— 4th) The " S" shift selector range changes the shift points under part throttle acceleration, allowing the transmission to stay in each lower gear for a longer period before automatically upshifting. With the shift selector in the " S" range, the " S 3 " indicator light in the dash pangil will come on and the transmission will shift from 1st to 2nd and 3rd but not 4th. This is especially useful when climbing or descending grades. While driving in the " S" range, the car's performance is improved but fuel economy is reduced. While driving in the " S" range, you can select 4th gear by pushing the " S 4 " switch. Depending upon vehicle speed and throttle pedal position, the transmission will shift to 4th gear when the switch is pressed; the "S 4" indicator light in the instrument panel will come on. Pushing the " S 4 " switch again will cause the transmission to downshift to 3rd gear in the " S 3 " mode. The " S 4 " indicator light in the instrument panel will go out, and the " S 3 " light on the in- strument panel will come on. If the shift lever is moved to any other driving range, the " S 4 " switch will be; cancelled automatically.

S4 SWITCH

Push

NOTE: If rapid acceleration is necessary, depress the accelerator to the floor; the transmission will automatically shift down according to load and engine speed. This applies to both D and S ranges.

(cont'd)

Main MenustShifting the Automatic (4WD) (cont'd)

2-1st/2nd

Use " 2" to increase engine braking when driving downhill and engine power when driving uphill. Using " 2" will allow the transmission to automatically shift up or down between the 1st gear and the 2nd gear. The maximum recommended speed for the " 2" range is: 62mph (100km/h) If you need more engine braking or engine power when using the " 2" position, push the When the speed is more than 31 mph (50 km/h): The indicator light in the instrument panel will come on but the transmission will remain in 2nd gear. However, when the speed goes below 31 mph (50 km/h), the transmission downshifts from 2nd to 1st and locks in 1st. The maximum recommended speed when locked in 1st gear is: 37mph (60km/h) To release the Low lock, push the any other driving range.

switch to use the 1st gear only.

switch again or select

Push

Main MenustR-Reverse CAUTION: Shift into or out of reverse only after the car has come to a complete stop; the transmission may be damaged if you shift while the car is moving.

P-Park CAUTION: Use this position when starting the engine, or when parking. Shift into Park only when the car is COMPLETELY stopped.

N-Neutral Use when starting the engine or during prolonged idling in traffic.

Main MenustReal Time 4WD

The 4WD system automatically engages between the front and rear wheels.

Service

To prevent sudden movement of the car, which may result in personal injury, always disengage the 4WD system manually before performing service that requires either the front or rear wheels to be raised and turning.

Towing CAUTION: Before towing the car with either the front or rear wheels raised off the ground, place the transmission in neutral and manually disengage the 4WD system to prevent the raised wheels from turning.

4WD Disengagement (Manual Transmission) 1. Locate the orange disengagement lever at the rear of the engine

compartment.

DISENGAGEMENT LEVER

2. Loosen the lock bolt at the slotted end of the lever. NOTE: For better accessibility, use a socket and a long extension bar. CAUTION: Do not loosen the lock bolt more than 5 — 7 turns. Replacement is extremely difficult.

Unlocked Position (4WD off)

Locked Position (4WD on)

MIDDLE BOLT

LOCK BOLT

10 mm

10 mm

3. Move the lever by turning the middle bolt counterclockwise. 4. Tighten the lock bolt.

NOTE: After service or towing is completed, return the lever to the normal (4WD on) position and tighten the lock bolt.

Main Menust4 WD Disengagement (Automatic Transmission) 1. Locate the disengagement plate at the rear of the transmission

case behind the right front wheel.

DISENGAGEMENT LEVER

2. Loosen the lock bolt in the notch on the plate.

NOTE: For better accessibility, use a socket and a long extension bar.

CAUTION: Do not loosen the lock bolt more than 5 — 7 turns. Replacement is extremely difficult.

Unlocked Position (4WD off)

Locked Position (4WD on)

MIDDLE BOLT

10 mm

LOCK BOLT

10 mm

3. Turn the middle bolt counterclockwise until the plate rotates

about 150° and is stopped by the lock bolt.

4. Tighten the lock bolt.

NOTE: After service or towing is completed, return the plate to the normal (4WD on) position and tighten the lock bolt.

Main MenustMaintenance Schedule and Records

Your Honda automobile must be properly maintained to ensure that it is in peak operating condition and the emission levels are within the standards set by the Federal Clean Air Act.

The following instructions and maintenance procedures are based on the assumption that your car will be used exclusively for the purpose for which it was designed:

1.To carry passengers and cargo within the load limits shown on

the label in the glove box.

2. To be driven on reasonable road surfaces within legal limits. 3. To generally be driven daily over a distance of several miles. 4. Use gasoline from pumps labeled unleaded, with a pump octane number of 86 or higher. The pump octane number is an average of the Research (R) octane and Motor (M) octane numbers.

NOTE: Failures which occur due to a lack of maintenance will not be covered under warranty. The Required Maintenance Schedule * specifies all maintenance required to keep your car in peak operating condition. Work should be done by an authorized Honda dealer but may be done by any qualified service facility or individual who is competent in this type of work. Maintenance, replacement, or repair of emission control devices and systems may be done by any automotive repair establishment or individual using parts that are "certified" to EPA standards. After the maintenance has been done, be sure to complete the Maintenance Records on pages 6 3, 64 — 6 5. A ll r e q u i r ed maintenance is considered normal owner operating cost and you will be charged for it by your dealer.

* Maintenance operations indicated by * 4 are recommended by the manufacturer for vehicle sold in California, but not required. Other maintenance operations are required by California regulations and condition the emission warranty. All operations (including *4) are required for vehicles sold outside California.

Main MenustCheck the following items at each fuel stop: 1. Engine oil level. 2. Radiator coolant level.

Check the following items periodically: 1. Brakes: for braking efficiency, brake pedal travel and hydraulic

fluid level.

2. Lights: for operation of headlights, taillights, side marker lights,

stoplights, turn signals and back-up lights.

3. Tires: for correct pressures (including spare); inspect for cuts and uneven or excessive wear. Rotate every 7,500 miles (12,000 km) in the pattern shown on page 90.

4. Steering: for excessive play or vibration while driving. 5. Exhaust system: for leaks or loose mounts. 6. Wipers: for operation of windshield wipers and washer, and

condition of wiper blades.

7. Seat belts: for condition of fabric and buckles, and operation of

the restraint mechanism.

8. Battery condition. 9. Clutch adjustment (clutch release arm travel).

(cont'd)

Main MenustMaintenance Schedule and Records (cont'd)

: Check oil and coolant level at each fuel stop. : Under severe driving conditions, service these items twice as often. (See page 64.)

Main MenustRequired Maintenance Record

Have your servicing dealer record all Required Maintenance below. Keep receipts for all work done on your car.

(cont'd)

Main MenustMaintenance Schedule and Records (cont'd)

Severe Driving Conditions CAUTION: The following items must be serviced more fre- quently on cars normally used under severe driving conditions. Refer to the chart below for the appropriate maintenance intervals. Severe driving conditions include: A: Repeated short distance driving B: Driving in dusty conditions C: Driving in severe cold weather D: Driving in areas using road salt or other corrosive

materials

E: Driving on rough and/or muddy roads

R —Replace I —Inspect

After inspection, clean, adjust, repair or replace if necessary.

Non-Scheduled Maintenance Record Record additional maintenance for severe driving conditions or non-scheduled maintenance on this page. (See page 78)

Main MenustMain MenustFluid Locations

ENGINE OIL FILLER CAP

AUTOMATIC TRANSMISSION FLUID DIPSTICK

POWER STEERING (CIVIC WAGON transmission and 4WD)

FLUID RESERVOIR with automatic

BRAKE FLUID RESERVOIR

RADIATOR CAP

ENGINE OIL DIPSTICK

WASHER FLUID RESERVOIR CAP

RADIATOR RESERVOIR CAP

Main MenustEngine Oil and Filter

Checking Check the engine oil a couple of minutes after shutting the engine off, with the car parked on level ground. Remove the dipstick and wipe it clean. Reinsert it all the way down, then pull it out and read the level. The level should be between the upper and lower marks.

ENGINE OIL FILLER CAP

UPPER

LOWER

DIPSTICK

DIPSTICK

Adding If the level has dropped close to the lower mark, add oil until it is even with the upper mark. 1.Turn the oil filler cap counterclockwise to remove. Add oil, then

check the level again. Do not overfill.

2. Reinstall the cap and twist clockwise until it stops.

CAUTION:

Be sure the oil filler cap is correctly replaced before starting the engine. Engine oil is a major factor affecting the performance and service life of the engine; you should use only a premium quality detergent oil labeled SG grade.

LOOK FOR THIS LABEL ON THE OIL Use the proper viscosity oil for the CONTAINER

climate in which you drive:

Ambient Temperature

Some oil labels may also include additional designations of quality such as CC or CD. However, these are acceptable only when used together with SG. NOTE: 5W-30 viscosity oil is recommended for improved fuel economy.

(cont'd)

Main MenustEngine Oil and Filter (cont'd)

Fuel Efficient Oil For the best fuel economy from your car, it is recommended that you use a fuel efficient SG oil. This oil is usually identified by the words such as: "Energy Conserving I I ," "Gas Saving," and "Fuel Saving," etc.

Changing Oil and Filter Engine oil and filter should be changed together every 6 months or 7,500 miles (12,000 km), whichever comes first. The filter is located on the engine block, below the intake manifold. A special "cap type" wrench is required (available from your Honda dealer). Use only a genuine Honda filter or its equivalent.

CAUTION: The oil filter cannot easily be removed from above the engine. For this reason it is recommended that the oil filter change be done by a skilled mechanic.

1. Start the car to warm up the

engine, then shut it off.

2. Remove the engine oil filler cap

and drain bolt, and drain the oil.

A warmed-up engine and the oil in it are hot; be careful not to burn yourself.

ENGINE OIL DRAIN BOLT

3. Remove the oil filter and let the

remaining oil drain out.

4. Install a new filter according to

instructions on or with the filter.

5. Reinstall the drain bolt with a new washer and tighten it securely. Refill the engine with the recommended oil, to the upper mark on the dipstick.

OIL FILTER

ENGINE OIL CAPACITY (including filter): 3.5

(3.7 US qt, 3.1 Imp qt)

Main Menust6. Reinstall the filler cap securely. 7. Start the engine and make sure oil is not leaking from the drain

bolt or filter.

8. Shut off the engine and recheck the oil level.

NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground.

CAUTION: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil.

Main MenustTransmission Oil/Fluid Check

Transmission oil/fluid must be checked with the engine off and the car on level ground.

If the engine has been running, some engine components may be hot enough to burn you.

CAUTION: If the oil/fluid level is low, check for possible leaks before adding oil. Do not overfill.

Since the transmission and differential are in the same housing, you are actually checking both oil/fluid levels in one procedure. Change transmission oil/fluid according to the Maintenance Schedule on page 62..

Manual Remove the oil filler bolt (beside the right axle). Feel inside the bolt hole with your finger. If the oil is up to the bottom edge of the hole, the oil level is correct. If it is not, slowly add oil until it runs out of the hole, then reinstall the bolt and tighten it securely with a wrench.

CORRECT LEVEL

OIL CHECK/ FILLER BOLT

MANUAL TRANSMISSION OIL CHANGE CAPACITY:

CIVIC WAGON: 1.8 l (1.9 US qt, 1.6 Imp qt) 4WD: 2.3 l (2.4 US qt, 2.0 Imp qt)

Use only SE or SF grade motor oil when adding or changing transmission oil.

Main MenustUse t he p r o p er viscosity oil for the climate in which you drive:

Ambient temperature

Automatic The automatic: transmission fluid level is checked (with the engine off and the car on level ground) using the dipstick in the right end of the transmission housing. Remove the dipstick and wipe it off.

4 WD

DIPSTICK

UPPER

LOWER

Insert the dipstick and remove it. The fluid level should be between the upper and lower marks. If necessary, add recheck. Use only DEXRON® II Automatic Transmission Fluid (A.T.F.) when adding or changing fluid. After checking the fluid level, push the dipstick in securely.

fluid and

AUTOMATIC TRANSMISSION FLUID CHANGE CAPACITY:

CIVIC WAGON: 4WD:

2.4 3.2

(2.5 US qt, 2.1 Imp qt) (3.4 US qt, 2.8 Imp qt)

Main MenustRear Differential Oil (4WD)

Rear differential oil must be checked or filled with the engine off and the car on the level ground.

CAUTION:

When checking the rear differential oil level, remember that if the car has been running, the differential and exhaust pipe will be hot. !f the oil level is low, check for possible leaks before adding oil. Do not overfill.

Remove the oil filler bolt. Feel inside the bolt hole with your finger. If the oil is up to the bottom edge of the hole, the oil level is correct. If it is not, slowly add oil until it runs out of the hole, then reinstall the bolt and tighten it securely with a wrench.

OIL CHECK/ FILLER BOLT

CORRECT LEVEL

REAR DIFFERENTIAL OIL CHANGE CAPACITY:

0.65

(0.69 US qt, 0.57 Imp qt)

Recommended oil: HYPOID GEAR OIL(API GL5)SAE90 above 5°C (41 °F) HYPOID GEAR OIL(API GL5)SAE80 below 5°C (41 °F)

Main MenustCooling System

Your Honda engine contains a number of aluminum parts. Therefore, it requires an antifreeze/coolant specifically formulated to protect the aluminum parts from corrosion. Failure to use a suitable antifreeze/coolant may seriously shorten the life of the engine as the result of rapid corrosion damage. Some antifreeze/coolants, although labeled for use in engines containing aluminum, may not provide adequate protection for your engine. Therefore, use only a Honda RECOMMENDED antifreeze/coolant. CHECK WITH YOUR AUTHORIZED HONDA DEALER. For best corrosion protection, the mixture of coolant and water must be maintained year-round at 50/50. Concentrations less than 50% coolant may not provide sufficient protection against corrosion and freezing. Concentrations of greater than 60% coolant will impair cooling efficiency and are not recommended. Low- mineral drinking water or distilled water should be mixed with the antifreeze/coolant. Coolant loss should be replenished by a mixture containing the proper concentration of antifreeze and water. Do not mix different antifreeze/coolants. Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator coolant. ENGINE DAMAGE CAUSED BY IMPROPER COOLANT USAGE IS NOT COVERED BY THE NEW CAR WARRANTY.

(cont'd)

Main MenustCooling System (cont'd)

Checking Coolant Check the coolant level in the reserve tank when the engine is at normal operating temperature.

there

If the level is below the MAX mark, but still visible, add a 50/50
solution of antifreeze and water to bring it up to MAX. If the reserve tank, the cooling system should be checked for leaks and if necessary. Coolant repaired must the radiator.

then be added

is no coolant

to

in

RESERVE TANK

MAX MIN

Do not remove the radiator cap when the engine is hot; the coolant is under pressure and could severely scald you.

CAUTION: Radiator coolant will damage paint. Quickly rinse any spilled coolant from painted surfaces.

Wait until the engine is cool, then turn the radiator cap counterclock- wise until it stops. DO NOT PRESS DOWN WHILE TURNING THE CAP. After any remaining pressure has been relieved, remove the cap by pressing down and again turning it counterclockwise. Add enough coolant to fill the radiator, and reinstall the cap. Be sure to tighten it securely. Fill the reserve tank up to the MAX mark with the engine cold.

Maintenance 1. Check

the hydrometer.

freeze protection

level of

the coolant with a

2. Keep the front of the radiator free of dirt and debris. 3. Check hoses and hose clamps regularly.

Main MenustReplacing Coolant Replace coolant at 36 months or 45,000 miles (72,000 km), whichever comes first. Thereafter, replace every 2 years or 30,000
miles (48,000 km), whichever comes first. RADIATOR COOLANT REFILL CAPACITY:

Manual Transmission (CIVIC WAGON): 4.5 (4WD): 4.4 Automatic Transmission (CIVIC WAGON): 4.4 (4WD): 4.8 Plus reserve tank 0.4

(1.19 US gal, 0.99 Imp gal)

(1.16 US gal, 0.97 Imp gal)

(1.16 US gal, 0.97 Imp gal)

(1.27 US gal, 1.06 Imp gal)

(0.11 US gal, 0.09 Imp gal)

1 .Turn the heater temperature control dial to maximum heat. 2. Remove the radiator cap and drain plug when the radiator is cool,

and drain the radiator.

RADIATOR CAP

BLEED BOLT

DRAIN PLUG

DRAIN BOLT

3. Remove the drain bolt from the front side of the cylinder block,

and drain the engine and heater.

4.Apply non-hardening sealant to the drain bolt threads, then

reinstall the bolt and tighten it securely. 5. Tighten the radiator drain plug securely. 6. Mix the recommended antifreeze with an equal amount of low- mineral or distilled water and fill the to maximum, as illustrated.

reservoir

Fill to here

M AX

MIN

(cont'd)

Main MenustCooling System (cont'd)

7. Loosen the air bleed bolt in the thermostat housing, then fill the radiator to the filler neck with the coolant mixture. Tighten the bleed bolt as soon as coolant starts to run out in a steady stream without bubbles.

FILLER NECK

Fill to here

8. With the radiator cap off, start the engine and let it run until warmed up (fan goes on at least twice). Then, if necessary, add more coolant mixture to bring the level back up to the filler neck. 9. Put the radiator cap on, then run the engine again and check for

leaks.

Main MenustBrakes

Brake System Design The diagonally-separated dual service brake system is designed so half the system will still provide braking action if the other half fails. However, stopping the car with only half the system will require more pedal pressure and pedal travel than normal. Also, the distance required to stop will be longer using only half the brake system. If the brakes fail suddenly, downshift to a lower gear for increased engine braking, and pull off the road as soon as possible.

It is dangerous to drive your car with a problem in either the brake electrical or hydraulic system; have your dealer check both systems if you suspect brake trouble. Do not ride the brakes. In other words, don't put your foot on the brake pedal unless you intend to brake. This causes excessive brake wear and can damage, or lead to loss of braking effectiveness through overheating. Your brake lights may also confuse drivers behind you. Driving through deep water may affect the brakes. Check their effectiveness by pressing the brake pedal gently. If the car does not slow down at the normal rate, continue gently applying the brakes, while maintaining a safe speed, until they dry out and normal performance returns.

Brake Wear Both front and rear brakes should be inspected for wear at the intervals shown in the maintenance schedule on page 62. When the brakes require maintenance, use only genuine Honda replacement parts or their equivalent.

(cont'd)

Main MenustBrakes (cont'd)

Front Brake Wear Indicators Your car is equipped with audible front brake wear indicators. When the brake pads wear to point that they should be replaced, they will make a "screeching" sound when the wheels are rolling and when the brakes are applied.

NOTE: Due to some driving habits or climates, brakes may "squeal" when you first apply them or when you have them partially applied; this is normal, and does not indicate excessive wear. The wear indicator makes a "screeching" sound while the brakes are applied.

Brake Fluid Check the fluid level in the brake fluid reservoir periodically; it should be between the MAX and MIN marks on the reservoir. If the level is near the MIN mark, add fluid to raise it to the MAX mark. Do not overfill. Use only brake fluid manufactured to DOT 3
or DOT 4 specifications (see reservoir cap) from a sealed container. Follow the manufacturer's instructions printed on the can.

NOTE: A low brake fluid level may be an indication of brake pad wear or of brake fluid leakage. You should have your brakes checked if the brake fluid level in the reservoir is low before refilling it.

BRAKE FLUID RESERVOIR

MAX MIN

CAUTION: The arrow on the reservoir cap must be pointing forward after the cap is installed. Make sure the brake warning switch wiring doesn't get caught between the cap and top edge of the reservoir.

Main MenustPower Steering

(4WD or CIVICWAGON with Automatic)

The power steering on your car provides easy handling while parking and maneuvering in traffic, without loss of road "feel" at highway speeds. An engine-driven hydraulic pump provides full power assist at low speeds and decreasing assist as the car goes faster.

CAUTION: If the power steering system should fail, or if the engine should stall, the car can still be steered. However, much greater effort will be required, particularly in sharp turns at low speed.

NOTE: You may feel a slight clunk or knock when turning the wheel with the engine off. This is a normal condition due to the design of the system.

RESERVOIR CAP

UPPER LOWER

Power Steering Fluid Check the power steering fluid level with the engine cold and the car parked on level ground. Make sure the fluid level is between the upper and lower marks on the reservoir. If the level has dropped close to or below the lower mark, check for leaks before adding fluid the upper mark. Do not overfill.

to

CAUTION: Use only genuine Honda power steering fluid. The use of other fluids such as A.T.F. or other manufacturer's power steering fluid will damage the system.

Main MenustAir and Fuel Filters

Air Filter Replace the air filter every 24 months or 30,000 miles (48,000 km), whichever comes first (more often in extremely dusty conditions).

Replacement Remove the four screws holding the air filter cover halves together. Remove the top half of the air filter cover. Replace the filter. Reinstall the cover and screws securely.

SCREWS

AIR FILTER

Fuel Filter The fuel filter is located in the engine compartment, on the right center of the firewall. It should be replaced at 60,000 miles (96,000
km) or 48 months whichever comes first, or any time you suspect contaminated gas may have clogged it.

CAUTION: Because the fuel system is under pressure, the filter should be replaced only by a qualified Honda technician.

Main MenustSpark Plugs

Spark plugs should be replaced every 24 months or 30,000 miles (48,000 km), whichever comes first.

Recommended spark plugs:

CAUTION: Never use spark plugs with an improper heat range; they will adversely affect engine performance and durability.

(cont'd)

Main MenustSpark Plugs (cont'd)

Spark Plug Replacement Replace plugs one at a time, so you don't get the wires mixed up. 1. Clean any dirt from around the spark plug base. 2. Disconnect the spark plug cap, then remove and discard the old

plug.

3. Check the gap of the new spark plugs before installation.

Plug gap should be: 1.1 mm ( 0.04in ) .

4. Thread the new spark plug in by hand to prevent cross-threading. 5. After the plug seats against the cylinder head, tighten 1/2 turn

with a spark plug wrench to compress the washer.

6. Reinstall the spark plug cap.

PLUG CAP

CAUTION: The spark plugs must be securely tightened, but not overtightened. A plug that's too loose can get very hot and possibly damage the engine; one that's too tight could damage the threads in the cylinder head.

Main MenustWiper Blades

For maximum visibility, replace worn or cracked wiper blades when you notice they do not wipe the windshield cleanly or smoothly.

To Replace Worn-out Blades: 1. Detach the blade assembly from the arm by pressing the lock tab in, then pushing the blade toward the base of the arm.

Press Lock Tab in

Push

2. Firmly grasp the end of the blade rubber and pull until the tabs are free of the metal support.

METAL SUPPORT

Pull out

TABS

3. Remove the metal retainers from the worn-out blade rubber and put them in a new blade rubber.

4. Insert the new blade rubber from the opposite side of the blade tabs and position the tabs in the metal support.

RETAINERS

Main MenustBattery

The condition of the battery can be determined by checking the test indicator. Service as required according to the label on the battery. Any corrosion around the positive and negative terminals should be washed off with a solution of baking soda and warm water. Dry the terminals and then coat them with grease.

TERMINAL

TEST INDICATOR

UPPER LOWER

TERMINAL

The battery gives off explosive gases; keep sparks, flames and cigarettes away. Provide adequate ventilation when charging or using the battery in an enclosed space. The battery contains sulfuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear protective clothing and a face shield. — If electrolyte gets on your skin, flush with water. — If electrolyte gets in your eyes, flush with water for at least

15 minutes and call a physician immediately.

Electrolyte is poisonous. — If swallowed, drink large quantities of water or milk and follow

with milk of magnesia or vegetable oil and call a physician.

KEEP OUT OF REACH OF CHILDREN.

Main MenustFuse Replacement

The fuse box is located under the dashboard on the driver's side. The circuits protected by each fuse are listed inside the box.

The fuses for automatic shoulder belt buckle motor are installed on the

terminal of the battery.

If any of your car's lights, accessories, or controls don't work, check their fuses. If a fuse has blown, the wire inside it will be burned through.

BLOWN

FUSE REMOVER

Checking the fuses: 1 .Turn off the ignition and all other switches. 2. If you find a blown or possibly faulty fuse, use the fuse remover, stored beside the spare fuse to pull the blown fuse out of its clips.

3. Check all other fuses as well as the one you suspect. 4. Push in a new fuse of the same rating, and make sure it fits tightly

in the clips. If it fits loosely, have your dealer fix it. If you don't have a spare, take a fuse of the same rating (or lower) out of a circuit you may not need, like the radio or cigarette lighter. Remember to replace the borrowed fuse and the missing spares.

CAUTION: A blown fuse may be just a symptom of some other problem. If a new fuse blows right away, the cause should be diagnosed and corrected by a qualified Honda technician. Never replace a fuse with anything but another fuse of the same or lower rating. A higher capacity fuse could cause damage and even start a fire.

(cont'd)

Main MenustFuse Replacement (cont'd)

The main fuse and some primary fuses are installed on the right front fender beside the battery.

If the circuits from the battery are ever overloaded (by a short in the system drawing too much current for example) the main or a primary fuse will blow, preventing damage to the entire wiring harness. If the main fuse blows, have a Honda dealer check the system, repair the cause, and replace the fuse.

CAUTION:

The electrical system is protected by fuses that are designed to fail and prevent damage to the wire harness. Always replace blown fuses with the same rating as specified to prevent wiring damage that can result in a possible fire. For proper electrical contact after replacing these fuses, make sure all screws are tight.

Main MenustBulb Replacement

NOTE: See page 110 for bulb specifications.

Front turn signal lights

Front side marker and parking lights

License plate lights

(cont'd)

Main MenustBulb Replacement (cont'd)

Rear side marker, turn signal, brake, taillights and back-up lights

Interior light

Luggage area light

High mount brake lamp

Main MenustThe factory-installed tires on your car were selected to provide the best performance for normal driving.

Tires

tire pressures

Inflation Pressures The tire label in the glove box lists recommended for carrying loads up to the limit shown. (Tire pressures are also listed on the back cover of this manual.) These pressures were chosen to provide you with the best combi- nation of tread life, riding comfort and stability under normal driving conditions. Improper reduce both tire life and load carrying capacity. Check tire pres- least once a month, sures at including the spare. Lower pressure than recommended lets the tread and sidewalls flex too much, causing increased tire temperatures, uneven wear, and poor handling Pressure higher than recommended can make the tire too stiff, increasing the chance of damage from road hazards, and also causing uneven wear.

inflation can

TIRE LABEL

the

CAUTION:

Check tire pressure when the tires are cold. (After the car has been parked for more than 3 hours or driven less than 1 mile/ 1.6 km). Tire pressure may increase as much as 41 kPa (6 psi) when the tire is hot, so NEVER ADJUST tire pressure when the tires are hot. Never inflate load range B tires to more than 220 kPa (32 psi) cold. Cars with luggage racks or cartop carriers DO NOT have greater load limits than those on the label.

Snow Tires If you use snow tires, they should have the same load capacity as the original equipment tires, and they must be installed in sets of four, or they may cause poor handling. They should be inflated to 28
kPa (4 psi) (cold) above the recommended pressure on the tire label in the glove box. Cars with snow tires should not be driven faster than 75 mph (120 km/h).

(cont'd)

Main MenustTires (cont'd)

Tire Chains When required, tire chains should be installed on the front wheels. If you are using metal type chains, make sure they are designated SAE Class " S ". You may also use plastic or cable type "chains". Use only the correct size chains recommended for your tire size and make sure they are installed following the chain manufacturer's instructions.

Once tire chains are installed, drive at less than 19 mph (30km/h) on roads covered with snow or ice. To minimize tire and chain wear, avoid driving on cleared roads with chains installed.

CAUTION: Improper installation or loose tire chains may damage your car's chassis and fenders.

NOTE: Keep the manufacturer's installation instructions in your glove box for future reference.

Tire Rotation Tires may wear unevenly when used for a long time at the same position on the car. To avoid this, rotate the tires every 7,500 miles (12,000 km). If abnormal or uneven wear develops between rotations, the cause should be found and corrected as soon as possible. The illustration shows how the tires can be rotated. The COMPACT spare tire must not be included in tire rotation.

NOTE: Front brake pads should be inspected for wear whenever the tires are rotated.

Front

Main MenustTire Balancing

Unbalanced tires may affect handling and tire wear. A tire should always be rebalanced after it has been dismounted from the wheel. Your original tires were properly balanced before the car left the factory, but may need rebalancing at some time during the life of the tire. Tire balancing for the COMPACT spare is not necessary.

Tire Traction

Worn tires or slippery road surfaces can reduce driving, cornering and braking traction. To reduce the possibility of losing traction, slow down when the road gets slippery, replace tires when wear indicators are visible, and KEEP TIRES PROPERLY INFLATED.

they should be

Tire Replacement The original tires on your car have indicate tread wear indicators to when replaced. The indicators appear as bands about 12.7 mm (1/2 in) wide when the tire tread depth is less than 1.6 mm (1/16 in). When indicators appear across t wo or more grooves in a row, you should replace the tiro.

INDICATOR LOCATION MARKS

TREAD WEAR INDICATORS

Driving on worn-out or under-inflated tires is very hazardous, and will reduce braking effectiveness, steering accuracy and traction.

When replacing tires, use only the recommended tire size. Wheel rim widths and offsets must be those recommended by American Honda Motor Co., Inc. Contact the Zone Office nearest you as shown on the inside of the back cover.

Tires and wheels other than those recommended may be unsafe. Do not mix radial and bias ply tires on the same car.

(cont'd)

Main MenustTires (cont'd)

Mixing radial and bias ply tires or different sized tires can adversely affect your car's handling, which could lead to loss of control and possible injury.

Additional 4 WD Tire Information Unevenly worn tires, or different sized tires, can cause the 4WD mechanism to engage abnormally, which may eventually damage the transmission. Therefore, observe the following precautions carefully:

Rotate the tires at least every 7,500 miles (12,000 km). Replace worn tires in sets of four. If replacement of all four tires is not practical (because of damage to an individual tire, for example), always replace with the same size, brand and type as those currently on the car.

Main MenustAir Conditioner Care

Condenser and Radiator Check the engine radiator and the air conditioner condenser (in front of the radiator) for accumulated dirt, insects or leaves. Carefully brush or hose them off to assure maximum cooling performance.

CAUTION: Radiator and condenser fins are very thin and easily damaged; do not bend them with the high water pressure or brush.

Compressor Drive Belt