Login- Download PDF Manual
-
seriously hurt a toddler who is not in the proper position or properly restrained.
We also recommend that any child who is too large to use an infant or toddler seat ride in one of the out- side positions of the rear seat. The child should then wear the lap/ shoulder belt properly for protection.
Important Safety Reminders Never hold a baby or child on your lap when riding in a car. If you are wearing your seat belt, the violent forces created during a crash will tear the child from your arms. The child could be seriously hurt or killed.
If you are holding a child and not wearing a seat belt in a crash, you could crush the child against the car's interior.
Never put your seat belt over yourself and a child. During a crash, the belt could press deep into the child, causing serious internal injuries.
Two children should never use the same seat belt. If they do, they could be very seriously injured in a crash.
Child Safety
If you are driving with small children in the car, you should use the childproof door locks to prevent them from opening the rear doors (see page 52).
For their safety, do not leave children alone in your car without adult supervision.
Driver and Passenger Safety
Main MenuTable of Contentsst Child Safety
General Guidelines for Restraining Children Under 18
kg (40 Ibs) Use an approved child seat. The seat must meet Federal Motor Vehicle Safety Standard 213 (FMVSS-213) or Canadian Motor Vehicle Safety Standards. Look for the manufac- turer's statement of compliance on the box and seat.Use a seat of the right size. Make sure the seat fits your child. Check the seat manufacturer's instructions and labels for height and weight limits.
Secure the child seat to the car. All approved child seats are designed to be secured to the car seat by the lap belt or the lap belt portion of a lap/ shoulder belt. A child whose seal is not properly secured to the car can be endangered in a crash.
Driver and Passenger Safety
Restraining an Infant Who Weighs Less Than 9 kg (20 Ibs)
To properly route a seat belt through a child seat, follow the seat maker's instructions. If you use a lap/ shoulder belt, be sure you install a locking clip on the belt (see page 24).
Secure the child in the child seat. Make sure the infant or child is firmly secured to the child seat. Use the straps provided, and carefully follow the manufacturer's instructions.
An infant up to about 9 kg (20 Ibs) must be restrained in an infant seat or a convertible seat designed for a baby. Because infants must ride in a reclining position, be sure the infant seat always faces the REAR of the car as shown.
Main MenuTable of Contentsst We recommend that, whenever possible, you put the infant seat in the center position of the rear seat and secure it to the car with the lap belt.
If you decide to put an infant seat in any other seating position, you must use a locking clip on the car's lap/ shoulder belt (see page 24).
If your car has a passenger's airbag, we strongly recommend that you do not put an infant seat in the front passenger's seat. If the airbag inflates, it can hit the infant seat with great force. The infant seat can be dislodged or struck with enough force to cause very serious injury to the infant.
Restraining a Child Who Weighs Between 9 and 18 kg (20 and 40
Ibs)Toddler seats are designed for children who weigh between 9 and 18 kg (20 and 40 Ibs).
Child Safety
The preferred place to put a toddler seat is in the center position of the rear seat. Use the car's lap belt to secure the seat to the car.
If you decide to put a toddler seat in any other seating position, you must use a locking clip on the car's lap/ shoulder belt (see page 24).
If you are using a toddler seat in the front passenger's seat, move the passenger's seat as far back as possible before installing the child seat. If the passenger's bag inflates, it could seriously hurt a toddler who is not in the proper position or properly restrained.
Driver and Passenger Safety
Main MenuTable of Contentsst Child Safety
Restraining a Child Who Weighs Over 18 kg (40 Ibs)
We recommend that, whenever possible, a child who has outgrown a toddler seat ride in one of the outside positions of the rear seat and use a lap/shoulder belt.
Driver and Passenger Safety
Put the seat belt on your child and check its fit. The shoulder belt should fit over the collarbone and across the chest. The lap belt should sit low on your child's hips, not across the stomach.
Using a Seat Belt Locking Clip Always use a seat belt locking clip when you secure a child seat to your car with a lap/shoulder belt. This helps prevent the seat from shifting position or overturning.
A locking clip is usually included with the child seat. If you need a clip, contact the seat's manufacturer or a store that sells child restraints.
If the shoulder belt crosses the neck, have your child move toward the center of the rear seat until the belt fits properly. If the belt still crosses the child's neck, you should use a booster seat.
Several styles of booster seats are available. We recommend a design that allows the child to use the car's lap/shoulder belt.
Whichever style you select, follow the booster seat manufacturer's instructions.
Main MenuTable of Contentsst To install a locking clip, do the following:
1. Place the child restraint in the desired position. Route the lap/ shoulder belt through the restraint according to the seat manufac- turer's instructions.
2. Insert the latch plate into the
buckle. Pull on the shoulder part of the belt to make sure there is no slack in the lap portion.
3. Tightly grasp the belt near the
latch plate. Pinch both parts of the belt together so they won't slip through the latch plate. Unbuckle the seat belt.
Child Safety
Using Child Restraints with Tethers
90 mm (3.5 in)
4. Install the locking clip as shown.
Position the clip as close as possible to the latch plate.
5. Insert the latch plate into the
buckle. Push and pull on the child seat to verify that it is held firmly in place. If it is not, repeat these steps until the restraint is secure.
290 mm (11.4 in)
Your Honda has three attachment points for tether-style child seats.
U.S. Models Use the dimensions in the above illustration to locate the attachment point you want to use. Cut a 12.7 mm (1/2 inch) diameter hole in the rear shelf.
CONTINUED
Driver and Passenger Safety
Main MenuTable of Contentsst Child Safety
Canadian Models Select the attachment point you want to use and remove the plug with a small flat-tipped screwdriver or fingernail file.
Then install the tether hardware that came with the child seat. Tighten the bolt to: 22 N·m(2.2 kg-m , 16 Ib-ft)
If you are not sure how to install the bracket, have it installed by your Honda dealer.
If you need an anchor plate and mounting hardware, you can obtain them by writing to:
American Honda Motor Co., Inc. Consumer Affairs 1919 Torrance Blvd. Torrance, CA 90501-2746
Driver and Passenger Safety
Canadian Cars
TOOTHED WASHER
Storing a Child Seat When you are not using an infant seat or other child restraint, either remove it or make sure it is properly secured so it cannot be thrown around the car during a crash.
The anchor plate and mounting hardware for a top tether are supplied with the car. When installing, make sure the toothed washer is on the bottom of the bolt.
The supplied anchor plate is designed only for mounting a child restraint. Do not use it for any other purpose.
Main MenuTable of Contentsst Alcohol and Drugs
Driving a car requires your full at- tention and alertness. Traffic condi- tions change rapidly. You must be able to react just as rapidly. Alcohol or drugs directly affect your alert- ness and ability to react. Even pre- scription and non-prescription medi- cines can have this effect.
There are laws that deal with drunken driving. These laws define how much alcohol it takes in your system to be legally "drunk." How- ever, your judgment and reaction time get worse with every drink — even the first one.
The safest thing you can do is never drink and drive. This can be done if you plan ahead. If you know you are going to be drinking, make plans to ride with a friend who will not be drinking.
If you have no choice but to drive, stop drinking and give yourself lots of time to sober up. Time is the only thing that can make you sober. Things like coffee or a cold shower don't speed up the process.
What if you find that you've been drinking and cannot get a ride from a friend? Find alternative transpor- tation. Call a taxi. Take a bus. Many communities have transportation services devoted to shuttling people who have been drinking.
If you see friends trying to get behind the wheel after drinking, stop them. Drive them yourself or arrange other transportation. If you think you are interfering, remember that your interference will keep them from sharing the road with you.
Driver and Passenger Safety
Main MenuTable of Contentsst Carbon Monoxide Hazard
Your car's exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the car in normal driving if you maintain your car properly. Have the exhaust system inspected for leaks whenever:
The car is raised for an oil change. You notice a change in the sound of the exhaust. The car was in an accident that may have damaged the underside.
Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and can even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the car out of the garage.
Driver and Passenger Safety
With the trunk lid open, air flow can pull exhaust gas into your car's interior and create a hazardous condition. If you must drive with the trunk lid open, open all the windows and set the heating and cooling system as follows.
If you must sit in your parked car, even in an unconfined area, with the engine running, adjust the heating and cooling system as follows:
1. Push the 2. Select the 3. Turn the fan on high speed. 4. Set the temperature control to a
button. mode.
comfortable setting.
Main MenuTable of Contentsst These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully and don't remove them.
If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.
BATTERY
Safety Labels
RADIATOR CAP
Driver and Passenger Safety
Main MenuTable of Contentsst This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach.
Control Locations............................ 32
Indicator Lights................................ 33
Gauges.............................................. 38
Speedometer................................ 38
Tachometer.................................. 38
Odometer...................................... 38
Trip Meter.................................... 38
Fuel Gauge................................... 39
Temperature Gauge.................... 39Controls Near the Steering
Wheel........................................40
Headlights.................................... 41
Daytime Running Lights............. 41
Instrument Panel Brightness..... 42
Turn Signals................................. 42
Windshield Wipers...................... 43
Windshield Washers................... 43
Hazard Warning........................... 44
Rear Window Defogger.............. 44
Steering Wheel Adjustment....... 45
Steering Wheel Controls ................ 46
Cruise Control.............................. 46
Horn.............................................. 49
Keys and Locks................................ 49
Keys.............................................. 49
Ignition Switch............................. 50Instruments and Controls
Door Locks................................... 51
Power Door Locks....................... 51
Childproof Door Locks............... 52
Trunk............................................ 52
Seat Adjustments............................. 54
Front Seat Adjustments.............. 54
Folding Rear Seat............................ 55
Power Windows............................... 56
Moonroof.......................................... 58
Sunshade....................................... 58
Mirrors.............................................. 59
Manual Door Mirrors.................. 59
Adjusting the Power Mirrors..... 59
Parking Brake.................................. 60
Glove Box......................................... 61
Digital Clock..................................... 62
Console Compartment.................... 63
Beverage Holder.............................. 63
Coin Box........................................... 64
Vanity Mirror................................... 64
Cigarette Lighter............................. 64
Ashtrays............................................ 65
Interior Light.................................... 66Instruments and Controls
Main Menust Control Locations
DOOR LOCK SWITCH (P.51)
POWER WINDOW SWITCH (P.56)
FUEL FILL DOOR RELEASE (P.92)
MIRROR CONTROLS (P.59)
DIGITAL CLOCK (P.62)
HEATING/ COOLING CONTROL (P.68)
AUDIO SYSTEM (P.75)
TRUNK RELEASE HANDLE (P.52)
HOOD RELEASE HANDLE (P.93)
Instruments and Controls
Main MenuTable of Contentsst Indicator Lights
PARKING BRAKE AND BRAKE SYSTEM INDICATOR*
ANTI-LOCK BRAKE SYSTEM INDICATOR
CRUISE CONTROL INDICATOR
HIGH BEAM INDICATOR
CHARGING SYSTEM INDICATOR
LOW OIL PRESSURE INDICATOR
The instrument panel has many indicators to give you important information about your car.
Lamp Check Many of the indicator lights come on when you turn the ignition switch ON (II), allowing you to see that they are working. The instrument panel should look like the illustration. If an indicator does not light during this test, it cannot alert you if that system develops a problem. Have the dealer check your car for burned-out bulbs or other problems.
* The U.S. instrument panel is shown. Differences for the Canadian model are noted in the text.
MALFUNCTION INDICATOR LAMP/ CHECK ENGINE LIGHT*
TRUNK-OPEN INDICATOR
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR
SEAT BELT REMINDER LIGHT
CONTINUED
Instruments and Controls
Main MenuTable of Contentsst Indicator Lights
CHARGING SYSTEM INDICATOR
LOW OIL PRESSURE INDICATOR
SEAT BELT REMINDER LIGHT
HIGH BEAM INDICATOR
PARKING BRAKE AND BRAKE SYSTEM INDICATOR*
Seat Belt Reminder Light
This indicator lights when you turn the ignition ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt.
If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.
* The U.S. instrument panel is shown. Differences for the Canadian model are noted in the text.
MALFUNCTION INDICATOR LAMP/ CHECK ENGINE LIGHT* TRUNK-OPEN INDICATOR
Instruments and Controls
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR
Main MenuTable of Contentsst Charging System Indicator
This light indicates the battery is not being charged. It should come on when the ignition is ON (II), and go out after the engine starts. If this light comes on while driving, the battery is not being charged. Turn to page 184 for information about what to do.
Low Oil Pressure Indicator
This indicator lights when the oil pressure in the engine drops low enough to cause damage. It should light when the ignition is ON (II) and go out after the engine starts. If this light comes on when the engine is running, there is a possibility of serious engine damage. Safely pull to the side of the road and shut off the engine as soon as you can. Turn to page 183 for instructions and precautions on checking the engine.
US
Canada
BRAKE
Parking Brake and Brake System Indicator This light has two functions:
1. It lights as a reminder that you
have set the parking brake. Driving with the parking brake set can damage the brakes and tires, and cause the Anti-lock brake system to turn off (see page 110).
2. It can indicate the brake fluid level
is low if it remains lit after you release the parking brake or comes on while driving. This is normally due to worn brake pads. Have your dealer check the braking system for worn pads or fluid leaks.
Indicator Lights
Supplemental Restraint SRS System Indicator Only on cars equipped with SRS The SRS light normally comes on for a few seconds when you turn the ignition ON (II). If it doesn't, or it stays on after the engine starts, something is wrong with the Supplemental Restraint System. It may also flash on and off to indicate a problem.
If you see any of these indications, the airbag may not work when needed in an accident. Take the car to your dealer promptly for diagnosis and service.
Instruments and Controls
Main MenuTable of Contentsst Trunk-open Indicator
This light comes on if the trunk lid is not closed tightly.
US
Canada
Malfunction Indicator Lamp
Check Engine Light
This light comes on for a few seconds when you turn the ignition switch ON (II). If it comes on at any other time, it indicates one of the engine's emission control systems may have a problem. Turn to page 185 for information about what to do.
Indicator Lights
Anti-lock Brake System (ABS) Indicator
ABS Only on cars equipped with ABS (see page 110) This light normally comes on when you turn the ignition ON (II) and goes off after the engine starts. If it comes on at any other time, there is a problem in the ABS. If this happens, stop the car in a safe place and turn off the engine. Reset the system by restarting the engine. Watch the ABS light. If it does not go off, or comes back on again while driving, take the car to your dealer to have it checked. With the light on, your car still has normal braking ability but no anti-lock.
Instruments and Controls
Main MenuTable of Contentsst Turn Signal and Hazard Warning Indicators
The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page 157). Replace the bulb as soon as possible, since other drivers cannot see that you are signalling.
When you turn on the Hazard Warning switch, both turn signal lights blink. All turn signals on the outside of the car should flash.
High Beam Indicator
This light comes on with the high beam headlights. See page 41 for information on the headlight controls.
On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page 41).
Cruise Control Indicator
CRUISE CONTROL Only on cars equipped with Cruise Control System This lights when you set the cruise control. See page 46 for information on operating the cruise control.
Indicator Lights
Shift Lever Position Indicator (Automatic Transmission only)
This indicator shows which shift position the shift lever is in.
Instruments and Controls
Main MenuTable of Contentsst Gauges
TACHOMETER
SPEEDOMETER
FUEL GAUGE
TEMPERATURE GAUGE
ODOMETER
TRIP METER
TRIP METER RESET BUTTON
Tachometer On LX and EX models in U.S., and EX model in Canada The tachometer shows the engine speed in revolutions per minute (rpm). To protect the engine from damage, never drive with the tachometer needle in the red zone.
Speedometer U.S. Models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h).
Canadian Models This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).
Instruments and Controls
Odometer The odometer shows the total dis- tance your car has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under federal law (in the U.S.) and provincial regulations (in Canada) to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. To reset it, push the trip meter reset button.
Main MenuTable of Contentsst TEMPERATURE GAUGE
SPEEDOMETER
FUEL GAUGE
ODOMETER
TRIP METER
TRIP METER RESET BUTTON
Fuel Gauge This shows how much fuel you have. It is most accurate when the car is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads.
The gauge stays at the same fuel level reading after you turn off the ignition. When you add fuel, the gauge slowly changes to the new reading after you turn the ignition back ON (II).
Gauges
Temperature Gauge This shows the temperature of the engine's coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper white mark. If it reaches the red " H" (Hot) mark, pull safely to the side of the road. Turn to page 181 for instructions and precautions on checking the engine's cooling system.
Instruments and Controls
Main MenuTable of Contentsst Controls Near the Steering Wheel
INSTRUMENT PANEL BRIGHTNESS
CRUISE CONTROL
HAZARD WARNING LIGHT
REAR WINDOW DEFOGGER
MOONROOF
The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield wipers.
The rear window defogger switch is on the dashboard to the right of the steering column.
The controls under the left air vent are for the moonroof, mirrors, cruise control and instrument panel brightness.
The lever on the underside of the steering column allows you to tilt the steering wheel.
MIRROR CONTROLS
Instruments and Controls
HEADLIGHTS/ TURN SIGNALS
TILT ADJUSTMENT
WINDSHIELD WIPERS/WASHERS
Main MenuTable of Contentsst Controls Near the Steering Wheel
Headlights
The rotating switch on the left lever controls the lights. Turning this switch to the first position " " turns on the parking lights, tail lights, instrument panel lights, side-marker lights, and rear license plate lights. Turning the switch to the second position "
" turns on the headlights.
To change between low beams and high beams, pull back on the turn signal lever until you hear a click, then let go. The blue high beam indicator will light (see page 37).
To flash the high beams, pull back and hold the turn signal lever. Release the lever and the high beams will go off.
The high beams will stay on for as long as you hold the lever, no matter what position the headlight switch is in.
Daytime Running Lights (Canadian Models) With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the switch.
Instruments and Controls
Main MenuTable of Contentsst Controls Near the Steering Wheel
Instrument Panel Brightness
Turn Signals
To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it.
The dial on the dashboard to the left of the instrument panel controls the brightness of the instrument panel lights. Turn the dial to adjust the brightness.
TURN SIGNAL LEVER
Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn.
Instruments and Controls
Main MenuTable of Contentsst Windshield Wipers
Windshield Washers
Controls Near the Steering Wheel
The right lever controls the wind- shield wipers and washers. The rotary switch at the end of the lever has three positions:
INT — intermittent LO — low speed HI— high speed
In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continu- ously.
To operate the wipers in mist mode, push the control lever down. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield.
To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.
On Canadian models The wipers run at low speed while you're pulling the lever, then complete one more sweep of the windshield after you release it.
Instruments and Controls
Main MenuTable of Contentsst Controls Near the Steering Wheel
Hazard Warning
Rear Window Defogger
Make sure the rear window is clear and you have good visibility before starting to drive.
The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.
Push the red button under the clock to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your car is disabled.
The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 25 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the car.
Instruments and Controls
Main MenuTable of Contentsst Steering Wheel Adjustment You can adjust the steering wheel height to suit your preference. Do this before you begin driving.
Adjusting the steering wheel position while driving may cause you to lose control of the car and be seriously injured in a crash.
Adjust the steering wheel only when the car is stopped.
Controls Near the Steering Wheel
3. Move the steering wheel up or
down to the desired position. Position the wheel so you can see all the instrument panel gauges and warning lights. Push the lever up to lock the steering wheel in that position.
4. Make sure you have securely
locked the steering wheel in place by trying to move it up and down.
1. Adjust the seat so you are a
comfortable distance from the pedals.
2. The lever to tilt the steering wheel
is under the steering column to the left. Push this lever all the way down.
Instruments and Controls
Main MenuTable of Contentsst Steering Wheel Controls
Cruise Control Available only on LX and EX models in the U.S., and EX model in Canada Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It is for cruising on straight, open highways. It is not recommended for conditions such as city driving, winding roads, slippery roads, heavy rain, or bad weather. You should have full control of the car under those conditions.
Improper use of the cruise control can lead to a crash.
Use the cruise control only when traveling on open highways in good weather.
Instruments and Controls
NOTICE
Using the Cruise Control
The cruise control, as it operates, moves the accelerator pedal. You can damage your car's accelerator mechanism by resting your foot under the pedal and blocking the movement.
1. Push in the Cruise Control Master
Switch to the left of the steering column. The indicator in the switch will light.
2. Accelerate to the desired cruising
speed above 25 mph (40 km/h).
Main MenuTable of Contentsst Changing the Set Speed You can increase the set cruising speed in either of two ways:
Press and hold the RESUME/ accel button. The car will acceler- ate slowly. When you reach the desired cruising speed, release the button.
Push on the accelerator pedal. Ac- celerate to the desired cruising speed and press the SET/decel button.
Steering Wheel Controls
You can decrease the set cruising speed in either of two ways:
Press and hold the SET/decel button. The car will decelerate. Release the button when you reach the desired speed.
Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL light on the instrument panel will go out. When the car slows to the desired speed, press the SET/decel button. The car will then maintain the desired speed.
CONTINUED
Instruments and Controls
RESUME/ accel
SET/decel
3. Press and hold the SET/decel
button on the steering wheel until the CRUISE CONTROL light on the instrument panel comes on. This shows the system is now activated.
The set speed may vary slightly, particularly on hills.
Main MenuTable of Contentsst Steering Wheel Controls
Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The car will return to the set cruising speed.
Resting your foot on the brake or clutch pedal will cause the cruise control to cancel.
Instruments and Controls
Cancelling the Cruise Control Any of these actions cause the cruise control to cancel.
Tap the brake or clutch pedal.
Press the SET/decel and RE- SUME/accel buttons at the same time.
Press the Cruise Control Master Switch.
When you tap the brake or clutch pedal, or press the SET and RE- SUME buttons at the same time, the CRUISE CONTROL light on the instrument panel will go out and the car will begin to slow down. You can use the accelerator pedal in the normal way.
If you use the brake or clutch pedal to cancel cruise control, the system retains the previously-set cruising speed. To return to that speed, ac-
celerate to above 25 mph (40 km/h) and press the RESUME/accel button until the CRUISE CONTROL light comes on. The car will accelerate to the same cruising speed as before.
If you cancel cruise control by pressing the SET and RESUME buttons at the same time, the previously-set cruising speed is erased. To use the cruise control, accelerate to the desired cruising speed and press the SET/decel button.
Pressing the Cruise Control Master Switch turns the system completely off and erases the previous cruising speed from memory. To use the system again, refer to Using the Cruise Control.
Main MenuTable of Contentsst Steering Wheel Controls, Keys and Locks
Horn
Keys
HORN BUTTONS
KEY NUMBER PLATE
VALET KEY
MASTER KEY
On cars equipped with SRS, press either of the buttons on the steering wheel spokes to sound the horn. On other cars, press the pad in the center of the steering wheel.
Your car comes with two kinds of keys: a master key and a valet key. The master key fits all locks on your car:
Ignition Doors Trunk Trunk release handle Rear seat trunk access
The valet key only works the ignition and the door locks. You can keep the trunk, trunk release handle and rear seat trunk access locked when you leave your car and valet key at a parking facility. (See Trunk, page 52.)
You should have received a key number plate with your set of keys. You will need this key number if you ever have to replace a lost key. Store this plate in a safe place. When replacing keys, use only Honda-approved key blanks.
Instruments and Controls
Main MenuTable of Contentsst Keys and Locks
Ignition Switch
The ignition switch is on the right side of the steering column. It has four positions: LOCK (0), ACCES- SORY (I), ON(II), and START (III).
Instruments and Controls
LOCK (0) — You can insert or remove the key only in this position. When you turn the key from LOCK to ACCESSORY, you may have to turn the steering wheel to release the anti-theft lock. To switch from ACCESSORY to LOCK, you must push the key in slightly as you turn it. If your car has an automatic trans- mission, it must also be in Park. The anti-theft lock will lock the steering column when you remove the key.
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control.
Remove the key from the ignition switch only when parked.
ACCESSORY (I) — In this position, you can operate the audio system and cigarette lighter.
ON (II) — This is the normal key position when driving. All features and accessories on the car are usable. Several of the lights on the instru- ment panel come on as a test when you turn the ignition switch from ACCESSORY to ON (see page 33).
START (III) — Use this position only to start the engine. The switch returns to ON when you let go of the key.
You will hear a reminder beeper if you open the driver's door with the key in the LOCK or ACCESSORY position. Remove the key to turn it off.
Main MenuTable of Contentsst Door Locks
The front doors can be locked and unlocked from the outside with the key.
Power Door Locks
Keys and Locks
Each door has a lock tab on the top. Push the tab down to lock the door and pull it up to unlock.
To lock any passenger's door when getting out of the car, push the lock tab down and close the door. To lock the driver's door, pull the outside door handle and push the lock tab down. Release the handle then close the door.
MASTER DOOR LOCK SWITCH Available only on LX and EX models in the U.S., and EX model in Canada This allows control of all door locks from the driver's door. Push the master door lock switch down to lock all doors, and up to unlock them.
CONTINUED
Instruments and Controls
Main MenuTable of Contentsst Keys and Locks
All doors lock when you push down the lock tab on the driver's door, or lock the driver's door from the outside with the key. Only the driver's door unlocks when you use the key or lock tab. To unlock the passen- gers' doors, use the master door lock switch or the lock tab on each door.
Childproof Door Locks
Trunk
LEVER
TRUNK RELEASE HANDLE
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up and use the outside door handle.
You can open the trunk in two ways:
Pull the trunk release handle to the left of the driver's seat.
Use the master key to open the trunk lock. The valet key does not work in this lock.
Instruments and Controls
Main MenuTable of Contentsst MASTER KEY
MASTER KEY
To close the trunk, press down on the trunk lid.
See page 98 for cargo loading and weight limit information. Keep the trunk lid closed at all times while driving to avoid damaging the lid and getting exhaust gas in the interior. See Carbon Monoxide Hazard on page 28.
To protect items in the trunk when you need to give the key to someone else, lock the trunk release handle with the master key and give the other person the valet key.
Keys and Locks
Instruments and Controls
Main MenuTable of Contentsst Seat Adjustments
Adjust the seat before you start driving.
Front Seat Adjustments
To adjust the seat forward and backward, pull up on the lever under the seat cushion's front edge. Move the seat to the desired position and release the lever. Try to move the seat to make sure it is locked in position.
To change the angle of the seat-back, pull up on the lever on the outside of the seat bottom. Move the seat-back to the desired position and release the lever. Let the seat-back latch in the new position.
Instruments and Controls
Main MenuTable of Contentsst Seat Adjustments, Folding Rear Seat
Folding Rear Seat The back of the rear seat folds down, giving you direct access to the trunk. The seat-back can be released from inside the car or inside the trunk.
MASTER KEY
Reclining the seat-back can decrease the protection you get from your seat belt in a crash.
You can slide under the seat belt and be seriously injured.
Adjust the seat-back to an upright position and sit well back in the seat.
To fold down the seat-back from inside the car, insert the master key in the lock on the rear shelf. Turn the key clockwise, pull down the top of the seat-back, then release the key.
CONTINUED
Instruments and Controls
Main MenuTable of Contentsst Folding Rear Seat, Power Windows
Make sure all items in the trunk, or items extending through the opening into the back seat, are tied down. Loose items can fly forward and cause injury if you have to brake hard. See Loading Cargo on page 98.
Never drive with the seat-back folded down and the trunk lid open. See Carbon Monoxide Hazard on page 28.
Power Windows Only on LX and EX models in the U.S., and EX model in Canada Your car's windows are electrically- powered. Turn the ignition switch to ON (II) to raise or lower any window.
Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pushing the switch up and holding it.
Pull
RELEASE LOOP
To release the seat-back from inside the trunk, pull the release loop under the rear shelf. Push the seat-back down, then let go of the loop.
To lock the seat-back upright, push it firmly against the rear shelf. Make sure it is latched in place by pulling on the top of the seat.
Instruments and Controls
Main MenuTable of Contentsst Power Windows
The master control panel also con- tains these extra features:
AUTO — To open the driver's window fully, push the window switch firmly down and release it. The window automatically goes all the way down. To stop the window from going all the way down, push the window switch up briefly.
The MAIN switch controls power to the passengers' windows. With this switch off, the passengers' windows cannot be raised or lowered. The MAIN switch does not affect the driver's window. Keep the MAIN switch off when you have children in the car so they do not injure them- selves by operating the windows unintentionally.
DRIVER'S WINDOW SWITCH
MAlN SWITCH
The driver's armrest has a master power window control panel. To open any of the passengers' windows, push down on the appropriate switch and hold it down until the window reaches the desired position. To close the window, push up on the window switch. Release the switch when the window gets to the position you want.
To open the driver's window only partially, push the window switch down lightly and hold it. The window will stop as soon as you release the switch.
The AUTO function only works to lower the driver's window. To raise the window, you must push the window switch up and hold it until the window reaches the desired position.
Closing a power window on a child's hands or fingers can cause serious injury.
Make sure your children are away from the windows before closing them.
Instruments and Controls
Main MenuTable of Contentsst Moonroof
Sunshade
Closing the moonroof on someone's hands or fingers can cause serious injury.
Make sure passengers are clear of the moonroof before closing it.
NOTICE
If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.
You can slide the sunshade to any position when the moonroof is closed. The sunshade slides open with the moonroof. You must close it manu- ally.
Only on EX model in the U.S. Use the switches on the dashboard under the left vent to operate the moonroof. The ignition must be ON (II). To lift the rear of the moonroof for ventilation, push the button. To slide the moonroof back, push the switch. Hold it until the moonroof reaches the desired position, then release the switch. To close the moonroof, press and hold the
switch.
Instruments and Controls
Main MenuTable of Contentsst Mirrors
Manual Door Mirrors
Adjusting the Power Mirrors
SELECTOR SWITCH
TAB
Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.
The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
Only on U.S. DX model and Canadian LX model with SRS The outside mirrors can be adjusted by moving the knob located on each front door.
Only on LX and EX models in the U.S., and EX model in Canada Adjust the outside mirrors with the adjustment switch on the left side of the dashboard:
On Canadian LX model without SRS The outside mirror on the driver's door can be adjusted by moving the knob on the inside of the door.
1. Turn the ignition switch ON (II).
2. Move the selector switch to L
(driver's side) or R (passenger's side).
CONTINUED
Instruments and Controls
Main MenuTable of Contentsst Mirrors, Parking Brake
ADJUSTMENT SWITCH
3. Push the appropriate edge of the
adjustment switch to move the mirror right, left, up or down.
4. When you finish, move the
selector switch to the center (off) position. This turns off the adjustment switch so you can't move a mirror out of position by accidentally bumping it.
Instruments and Controls
Parking Brake
The outside mirror on the passenger's side has curved glass. Objects look farther away than they are. Use this mirror to get a "wide view". Don't use it to judge the distance of things behind you.
PARKING BRAKE LEVER
To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake light on the instrument panel should go out when the parking brake is fully released (see page 35). If you try to drive the car without releasing the parking brake, the ABS cannot work properly.
Main MenuTable of Contentsst NOTICE
Glove Box
Driving the car with the parking brake applied can damage the rear brakes and axles.
GLOVE BOX
Open the glove box by pulling the handle. Close it with a firm push.
Parking Brake, Glove Box
An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Always keep the glove box closed while driving.
Instruments and Controls
Main MenuTable of Contentsst Digital Clock
RESET
(Not in U.S. DX and Canadian LX models) The digital clock displays the time with the ignition switch ON (II). To see the time with the ignition off, press and hold the wide button under the clock.
To set the clock:
1. Turn the ignition switch ON (II) to
display the time.
2. Swing down the front cover of the
wide button under the clock display. You will see H, M, and RESET buttons.
Instruments and Controls
3. Press and hold the H button until the hour advances to the desired time.
4. Press and hold the M button until
the numbers advance to the desired time.
You can use the RESET button to quickly set the time to the nearest hour. If the displayed time is before the half hour, pressing the RESET button sets the clock back to the previous hour. If the displayed time is after the half hour, pressing the RESET button sets the clock for- ward to the beginning of the next hour.
For example:
1:06 would RESET backward to 1:00. 1:52 would RESET forward to 2:00.
Main MenuTable of Contentsst Console Compartment, Beverage Holder
Console Compartment
Beverage Holder
Push
CONSOLE COMPARTMENT Only on LX and EX models in the U.S., and EX model in Canada To open the console compartment, pull up the front edge of the lid.
To open the beverage holder, push on the top. It is spring-loaded and will swing open. To close it, push it down until it latches.
Use the beverage holder only when the car is parked. If you place cups in the holder while driving, the liquid may spill when you go over bumps or around corners.
Be careful when you are using the beverage holder. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior. If the liquid is very hot, it can scald you or your passengers.
Instruments and Controls
Main MenuTable of Contentsst Coin Box, Vanity Mirror, Cigarette Lighter
Coin Box
Vanity Mirror
Cigarette Lighter
CIGARETTE LIGHTER
COIN BOX
To open the coin box, pull the upper edge. Close it with a firm push.
Only on LX and EX models in the U.S., and EX model in Canada To use the vanity mirror, pull down the passenger's sun visor.
The ignition switch must be in ACCESSORY (I) or ON (II) for the cigarette lighter to work. To heat up the lighter, push it in. It will pop out when it is ready for use. Do not hold the lighter in while it is heating up, you could cause it to overheat.
Instruments and Controls
Main MenuTable of Contentsst ASHTRAY
ASHTRAY
Open the front ashtray by pulling on the bottom edge. Push it in to close it. To remove the ashtray for emptying, push down on the metal plate inside, then pull the ashtray out completely.
The rear ashtray is at the rear end of the center console. Open the ashtray by swinging the upper edge of the lid down. To remove the ashtray for emptying, open it then lift up and out.
Ashtrays
NOTICE
Use the ashtray only for cigarettes, cigars and other smoking materials. To prevent a possible fire and damage to your car, don't put paper or other things that can burn in the ashtray.
Instruments and Controls
Main MenuTable of Contentsst Interior Light
(US: EX)
DOOR ACTIVATED ON
OFF
(US: DX, LX, Canada: LX, EX)
DOOR ACTIVATED OFF
ON
The interior light has a three- position switch. In the OFF position, the light does not come on. In the center position, the interior light comes on when you open any door. In the ON position, the interior light stays on continuously.
Instruments and Controls
Main MenuTable of Contentsst Comfort and Convenience Features
The heating and air conditioning* system in your car provides a com- fortable driving environment in all weather conditions.
(On the LX and EX models in the U.S., and EX model in Canada) The standard audio system is very versatile. To get the most benefit from this system, read its description in this manual.
Some models have an anti-theft audio system that requires a code number to enable it.
(For other U.S. and Canadian models) Refer to the operating instructions that came with the optional audio system you selected.
* Air conditioning is standard on the EX model in the U.S. It is optional on other models.
Heating and Cooling........................ 68
What Each Control Does............ 70
How to Use the System............... 71Controlling Air Flow
Direction............................... 71
Ventilation................................ 71
To Cool with A/C .................... 72
To Heat..................................... 73
To Heat and Dehumidifywith Air Conditioning.......... 73
To Defog and Defrost............. 74
To Turn Everything Off ............. 74
Audio System................................... 75AM/FM/Cassette Stereo
Audio System........................... 75
Operating the Radio.................... 77
Presetting..................................... 79
Adjusting the Sound.................... 80
Radio Frequencies....................... 81
Operating the Cassette Player... 82
Cassette Search Functions......... 83
Caring for Cassettes.................... 83
Operating the CD Changer........ 84
CD Error Indications................... 86
Caring for the Cassette Player....... 87
Theft Protection............................... 88Comfort and Convenience Features
Main Menust Heating and Cooling
This system has full heating, venti- lation, and air conditioning capabi- lities. You can adjust the system controls to mix these in various combinations. The air flows into the interior at three possible levels, which you can select.
(Only for DX and LX models in the U.S., and LX and EX models in Canada) If you purchased your car without air conditioning, it can be installed at any time. A Genuine Honda air conditioning system is available from your dealer. It meets Honda's high quality standards and is designed to fit your car. Please contact your dealer for more information.
Comfort and Convenience Features
CENTER VENT
SIDE VENT
CLOSE
The direction of air flow from the vents in the center and each side of the dashboard is adjustable. Move the tab in the center of each vent up- and-down and side-to-side.
The heating and cooling system draws air through the exterior vents at the bottom of the windshield. Keep these vents clear of leaves and other debris.
The side and upper vents can be opened and closed with the dials next to them.
Main MenuTable of Contentsst UPPER VENT
OPEN
CLOSE
Heating and Cooling
Comfort and Convenience Features
Main MenuTable of Contentsst Heating and Cooling
What Each Control Does
Fan Control Lever Sliding this lever to the right increases the fan speed, which increases air flow.
Temperature Control Lever Sliding this lever to the right increases the temperature of air flowing from the system.
Mode Buttons These buttons control the direction of air flow. The indicator light shows which button is controlling air flow.
Air Conditioning (A/C) Switch This switch turns the air condi- tioning ON and OFF. The indicator in the switch lights when the A/C is ON.
Comfort and Convenience Features
RECIRCULATION BUTTON
AIR CONDITIONING SWITCH
MODE BUTTONS
FRESH AIR BUTTON
TEMPERATURE CONTROL LEVER
FAN CONTROL LEVER
Fresh Air and Recirculation Buttons These two buttons control the source of air going into the system. In Fresh Air mode , air comes from outside the car. In Recirculation mode , the interior air recycles through the system.
Main MenuTable of Contentsst How to Use the System This section covers the best way to use the system for ventilation, cooling, dehumidifying, defrosting and heating. In most cases, the mode and air source selections are only recommendations. You may prefer different settings.
Use mode to heat or cool the interior more quickly, or to keep out smoke and dust. Leaving the system in the recirculation mode with the A/C off can cause the windows to fog up. Switch to mode as soon as the interior reaches a comfortable temperature or the outside smoky, dusty condition clears.
Heating and Cooling
The engine must be running for the heater and air conditioning to pro- vide hot and cold air. The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air circulating.
The air conditioning system does not depend on engine temperature. It can produce cold air almost immedi- ately.
Ventilation Your car has a flow-through venti- lation system. Air enters the car through vents in front of the wind- shield. It circulates through the interior then exits through vents near the rear window. This system provides fresh air even when the car is standing still. To bring in outside air, press the button. Set the fan at a comfortable speed.
Controlling Air Flow Direction Air flows into the interior at three levels: Toward the floor through the dash vents toward the windshield and side windows flow level or combination of levels with the five mode buttons.
. You select the air
and
CONTINUED
Comfort and Convenience Features
Main MenuTable of Contentsst Heating and Cooling
To Cool with A/C To operate the air conditioning system, press the air conditioning switch. Set the fan to the desired speed. You can also use the
mode button to direct air out
of the dash and heater vents.
To cool the interior down rapidly after the car has been sitting in the sun:
1. Start the engine. 2. Turn on the A/C by pressing the
switch.
3. Set the fan to maximum speed. 4. Open the windows partially. Select
and
When the interior reaches a com- fortable temperature, close the windows and set the system for cooling as described above.
Comfort and Convenience Features
MODE BUTTONS
AIR CONDITIONING SWITCH
TEMPERATURE CONTROL LEVER
FAN CONTROL LEVER
Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 39) when using the A/C in heavy traffic or driving up long hills. If it moves near the red zone, turn off the air conditioning until the gauge reads normally.
Main MenuTable of Contentsst To Heat To warm the interior:
MODE BUTTONS
AIR CONDITIONING SWITCH
Heating and Cooling
1. Start the engine. 2. Select 3. Switch the fan to the desired
and
speed.
4. Adjust the warmth of the air with
the temperature control lever.
To Heat and Dehumidify with Air Conditioning Air conditioning removes moisture from the air as it operates. When used in combination with the heater, it makes the interior warm and dry.
1. Switch the fan on. 2. Turn on the air conditioning. 3. Select
and any desired
mode button.
4. Adjust the temperature control
lever so the mixture of heated and cooled air feels comfortable.
TEMPERATURE CONTROL LEVER
FAN CONTROL LEVER
This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).
CONTINUED
Comfort and Convenience Features
Main MenuTable of Contentsst Heating and Cooling
To Defog and Defrost To remove fog from the inside of the windows:
1. Switch the fan on. 2. Turn on the air conditioning. 3. Select 4. Adjust the temperature control
and
lever so the airflow from the defroster vents feels warm.
5. Turn on the rear window defogger
to help clear the rear window.
To remove exterior frost or ice from the windshield and side windows after the car has been sitting out in cold weather:
1. Start the engine. 2. Select 3. Switch the fan and temperature
and
controls to maximum.
Comfort and Convenience Features
To Turn Everything Off To shut off the system temporarily, slide the fan speed and temperature control levers all the way to the left.
You should shut the system com- pletely off only for the first few minutes of driving in cold weather, until the engine coolant warms up enough to operate the heater. Keep the fan on at all other times so stale air does not build up in the interior.
To rapidly remove exterior frost or ice from the windshield (on very cold days), first select windshield is clear, select avoid fogging the windows.
. Once the to
These settings direct all the air flow to the defroster vents at the base of the windshield and the side window defroster vents. The air flow will get
