Download PDF Manual

behind the center seat, and attach the hooks to the anchor located directly behind the center rear seat located under a plastic cover. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint through the center seat tether strap loop and anchor to the tether strap loop located behind either outboard seating positions.


76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufactur- er’s instructions. Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug • Check belt fit periodically. A child’s squirming or


as possible.


slouching can move the belt out of position.


If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.


Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.


ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided.


The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your Ve- hicle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77


SAFETY TIPS


Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.


WARNING!


• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and


using a seat belt properly.


78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas


WARNING!


Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips:


Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.


If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.


Safety Checks You Should Make Inside the Vehicle


Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79


Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer is inoperable. Periodic Safety Checks You Should Make Outside the Vehicle


for service if your defroster


Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.


80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CONTENTS


䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87
▫ Automatic Dimming Mirror —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 88
▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 88
▫ Outside Mirrors Folding Feature . . . . . . . . . . 89
▫ Power Mirrors — If Equipped . . . . . . . . . . . . 90
▫ Heated Mirrors — If Equipped . . . . . . . . . . . . 91
▫ Driver’s Automatic Dimming Mirror —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 91


▫ Illuminated Vanity Mirror — If Equipped . . . . 92
▫ “Slide-On-Rod” Features Of Sun Visor —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 92
▫ Trailer Towing Mirrors — If Equipped . . . . . . 93
䡵 Uconnect™ phone — If Equipped . . . . . . . . . . . 94
䡵 Voice Command — If Equipped . . . . . . . . . . . . 94
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
▫ Manual Seat Adjuster — If Equipped . . . . . . . 95
▫ Manual Reclining Seats — If Equipped . . . . . . 96


82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


▫ Adjustable Head Restraints . . . . . . . . . . . . . . 97
▫ Eight-Way Power Seats — If Equipped . . . . . 100
▫ Power Lumbar — If Equipped . . . . . . . . . . . 101
▫ Heated Seats — If Equipped . . . . . . . . . . . . 102
▫ Ventilated Seats — If Equipped . . . . . . . . . . 104
▫ 40-20-40 Front Bench Seat — If Equipped . . . 104
▫ Mega Cab威 Rear Seat Features . . . . . . . . . . . 105
䡵 Driver Memory Seat — If Equipped . . . . . . . . 108


▫ Setting Memory Positions And Linking RKE


Transmitter To Memory . . . . . . . . . . . . . . . . 109
▫ Memory Position Recall . . . . . . . . . . . . . . . . 110
▫ To Disable a RKE Transmitter Linked To


Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
▫ Self-Limiting Control . . . . . . . . . . . . . . . . . . 112


▫ Driver Easy Exit And Easy Entry Control


. . . 112
䡵 To Open And Close The Hood . . . . . . . . . . . . 113
䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 116
▫ Automatic Headlights — If Equipped . . . . . . 116
▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 117
▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . 118
▫ Parking Lights And Panel Lights . . . . . . . . . 118
▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 118
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 119
▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . 120
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 120
▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . 120


▫ Daytime Running Lights (DRL)


▫ Multifunction Lever


䡵 Windshield Wipers And Washers


(Canada Only And Fleet Vehicles) . . . . . . . . . 121
. . . . . . . . . . . . . . . . . . 121
. . . . . . . . . . 123
▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . 123
▫ Windshield Washers . . . . . . . . . . . . . . . . . . 124
▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 124
䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . 124
䡵 Heated Steering Wheel — If Equipped . . . . . . 125
䡵 Driver Adjustable Pedals — If Equipped . . . . . 127
. . . . . . . . . . . . . . . . . . . . . . . . 127
䡵 Electronic Speed Control — If Equipped . . . . . 128
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 129


▫ Adjustment


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 129
▫ Deactivating Electronic Speed Control . . . . . . 130
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 130
▫ Varying The Speed Setting . . . . . . . . . . . . . . 130
▫ To Accelerate For Passing . . . . . . . . . . . . . . 131
䡵 Parksense威 Rear Park Assist — If Equipped . . . 132
▫ Parksense威 Sensors . . . . . . . . . . . . . . . . . . . 132
▫ Parksense威 Warning Display . . . . . . . . . . . . 132
▫ Enable/Disable Parksense威 . . . . . . . . . . . . . 137
▫ Service Parksense威 . . . . . . . . . . . . . . . . . . . 138
▫ Cleaning Parksense威 . . . . . . . . . . . . . . . . . . 138
▫ Parksense威 System Usage


And Precautions . . . . . . . . . . . . . . . . . . . . . 138


84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Parkview威 Rear Back Up Camera —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 141
▫ Turning Parkview威 On Or Off —


With Navigation/Multimedia Radio . . . . . . . 142


▫ Turning Parkview威 On Or Off —


▫ Courtesy/Reading Lights


Without Navigation/Multimedia Radio . . . . . 143
䡵 Overhead Console — If Equipped . . . . . . . . . . 143
. . . . . . . . . . . . . . 144
䡵 Garage Door Opener — If Equipped . . . . . . . . 145
▫ Programming HomeLink威 . . . . . . . . . . . . . . 147
▫ Gate Operator/Canadian Programming . . . . 149
▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 150
▫ Reprogramming A Single HomeLink威


Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150


▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 151
▫ General Information . . . . . . . . . . . . . . . . . . 151
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 152
▫ Open Sunroof — Express Mode . . . . . . . . . . 153
▫ Closing Sunroof — Express . . . . . . . . . . . . . 153
▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 153
▫ Pinch Protect Override . . . . . . . . . . . . . . . . 153
▫ Venting Sunroof — Express . . . . . . . . . . . . . 153
▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 154
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 154
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 154
▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 154


䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 154
䡵 Cigar Lighter And Ash Receiver —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 158
䡵 Power Inverter — If Equipped . . . . . . . . . . . . 159
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 161


▫ Front Instrument Panel Cupholders —


(40–20–40 Seats)


. . . . . . . . . . . . . . . . . . . . . 161


▫ Front Instrument Panel Cupholders —


Floor Mounted Shifter . . . . . . . . . . . . . . . . . 162
▫ Rear Cupholder — Quad Cab威 . . . . . . . . . . 162
▫ Rear Cupholder — Crew Cab . . . . . . . . . . . 163
䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
▫ Glove Box Storage . . . . . . . . . . . . . . . . . . . 163
▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 165


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
▫ Center Storage Compartment —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 166


▫ Second Row In-Floor Storage Bin —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 168
▫ Seatback Storage . . . . . . . . . . . . . . . . . . . . . 169
▫ Storage (Regular Cab) . . . . . . . . . . . . . . . . . 169
▫ Storage And Seats (Crew Cab) . . . . . . . . . . . 170
▫ Plastic Grocery Bag Retainers


(Regular Cab Models)


. . . . . . . . . . . . . . . . . 170
䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 171
▫ Rear Window Defroster . . . . . . . . . . . . . . . . 171
▫ Power Sliding Rear Window —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 172


▫ Manual Sliding Rear Window —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 172


86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . 173
䡵 Rambox威 — If Equipped . . . . . . . . . . . . . . . . 175


▫ Rambox威 Integrated Box Side


Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . 176
▫ Rambox威 Safety Warning . . . . . . . . . . . . . . . 179
▫ Bed Extender — If Equipped . . . . . . . . . . . . 180
▫ Bed Rail Tie-Down System . . . . . . . . . . . . . . 187


䡵 Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . 189
▫ Camper Applications . . . . . . . . . . . . . . . . . . 189
䡵 Easy-Off Tailgate . . . . . . . . . . . . . . . . . . . . . . 189


▫ Disconnecting The Rear Camera —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 189
▫ Removing The Tailgate . . . . . . . . . . . . . . . . 190
▫ Locking Tailgate — If Equipped . . . . . . . . . . 191


MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle).


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87


Adjusting Rearview Mirror


The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror should be adjusted to center on the view through the rear window.


88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the power button at the base of the mirror. A light next to the button will illuminate when the dimming feature is activated.


CAUTION!


To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.


Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.


Automatic Dimming Mirror


WARNING!


Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex right side mirror.


Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89


Folding Mirror


CAUTION!


It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location.


90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel.


The power mirror controls consist of mirror select but- tons and a four-way mirror control switch.


Power Mirror Controls


Power Mirror Controls


1 — Mirror Select Buttons 2 — Mirror Control


To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91


Heated Mirrors — If Equipped


These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Driver’s Automatic Dimming Mirror — If Equipped The driver’s outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirror will automatically adjust for headlight glare when the inside mirror adjusts.


Power Mirror Movement


92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover turns off the light.


“Slide-On-Rod” Features of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position.


Illuminated Vanity Mirror


Slide-On-Rod Extender


Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out).


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately.


Trailer Towing Position


Blindspot Mirror


94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED


Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.


VOICE COMMAND — IF EQUIPPED Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details.


SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. Proper use of the seats is needed for safe operation of the vehicle.


WARNING!


• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and


using a seat belt properly.


Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat. Pull up on the handle and slide the seat forward or backward to move the seat into the most comfortable position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95


Manual Seat Adjuster


96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.


Manual Reclining Seats — If Equipped The recliner handle is located on the outside of the seat cushion and is used to adjust the seatback position. To adjust the seatback, lift upward on the handle, lean back on the seatback and release the handle at the desired position. To return the seatback, lift upward on the handle, lean forward and release the handle at the desired position.


Recline Handle


WARNING!


• Actuating the recliner handle will allow the seat- back to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin behind the seat. To avoid injury, place your hand on the seatback and actuate the handle then posi- tion the seatback in the desired position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97


WARNING! (Continued)


• You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.


(Continued)


Adjustable Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear.


98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint.


To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint.


Adjusting Head Restraint


Removing Head Restraint


To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest


until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle.


WARNING!


Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK.


Rear Head Restraints The outboard head restraints can be adjusted. To raise the head restraint, pull upward on the head restraint. To


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint.


Adjustable Rear Head Restraints


NOTE: The rear center head restraint (Crew Cab only) is fixed and cannot be adjusted.


100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback to position yourself in the most comfortable driving position. Push forward or rearward on the switch and the seatback will move in either direction.


Power Seat Switches


1 — Power Seat Switch 2 — Power Seatback Switch


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101


Power Lumbar — If Equipped The lumbar controls are located on the outboard side of the seat cushion. The lumbar support can be increased by pressing the front of the switch and decreased by press- ing the back of the switch.


WARNING!


Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.


CAUTION!


DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.


Lumbar Control Switch


102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.


Heated Seats — If Equipped Both front seats and rear passenger seats can be equipped with heaters. The switches for the front seats are located in the instrument panel under the climate controls. The switches for the rear passenger seats are located on the back of the center console. After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.


Press the switch once to select High- level heating. Press the switch a sec- ond time to select Low-level heating. Press the switch a third time to shut the heating elements Off.


NOTE: The engine must be running for the heated seats to operate. The heated seats switch from High to Low and from Low to Off automatically, based on time and temperature of the seat. The heated seats can operate on High heat for as little as 4 minutes and up to 30 minutes before switching to Low heat. Once a seat has switched to the Low heat setting it may operate for an additional 60 minutes before automatically shutting Off. The heated seats can shut Off early or may not turn on when the seat is already warm.


NOTE: The drivers heated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information.


WARNING!


• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.


(Continued)


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103


WARNING! (Continued)


• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.


CAUTION!


Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat.


104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ventilated Seats — If Equipped Located in the seat cushion and seatback are small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compart- ment. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering to help keep the driver cooler in higher ambient tempera- tures. The ventilated seat switches are located in the switch bank in the center stack of the instrument panel, just below the climate controls. The fans operate at two speeds, High and Low.


Press the switch once to choose High, press it a second time to choose Low. Pressing the switch a third time will turn the ventilated seat Off. When High speed is selected both lights on


the switch will be illuminated. When Low speed is selected one light will be illuminated. NOTE: • The engine must be running for the ventilated seats to • The drivers ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information.


operate.


40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).


Mega Cab姞 Rear Seat Features


Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion. Pull upward on the handle, to release the seatback, and lean forward or rearward to the desired position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105


WARNING!


Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.


Rear Seat Recliner Handle


106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint.


2. Fold the seatback forward.


Table Mode Handle


Table Mode


3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding Rear Seat — If Equipped Both the left and right rear seats will drop and move forward when the seatback is folded flat.


WARNING!


• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and • Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop and strike someone in the vehicle, causing serious injury or possible death.


using a seat belt properly.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107


To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats.


Handle


108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down and push the seat forward.


Rear Passenger Fold Flat Seats


3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place.


WARNING!


Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.


DRIVER MEMORY SEAT — IF EQUIPPED The memory seat buttons are located on the outboard side of the drivers seat cushion.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to two RKE transmitters, each RKE transmitter linked to either of the two memory positions. Setting Memory Positions and Linking RKE Transmitter to Memory


NOTE: Each time the S (SET) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 1. Turn the vehicle key to the ON/RUN position.


Memory Seat Buttons


The memory buttons 1 and 2 can be programmed to recall the driver’s seat position, driver’s outside mirror position, adjustable brake, accelerator pedals position, Automatic Temperature Control (ATC) temperature set- ting and radio station preset settings. Your Remote


110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust the driver’s seat, recliner, and both sideview mirrors to the desired positions. NOTE: Not all motors may be moved at one time. Refer to “Seats/Eight-Way Power Seat” in this section for further information. 3. Adjust the brake and accelerator pedals to the desired positions. 4. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 5. Adjust while the ATC is in Auto mode. 6. Press and release the SET button located on the driver’s seat. 7. Within five seconds, press and release MEMORY button 1 or 2 on the driver’s seat. The next steps must be


the Automatic Temperature Control (ATC)


performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 8. Turn the ignition OFF and remove the key. 9. Press and release the LOCK button on one of the RKE transmitters. 10. Repeat the above steps to set the next memory position using the other numbered memory button or to link another RKE transmitter to memory. NOTE: A chime sound may be heard if Setting Memory was inhibited for any reason. Memory Position Recall NOTE: • The vehicle must be in PARK to recall memory posi-


tions.


• Not all motors may be moved at one time. Refer to the “Seats/Eight-Way Power Seat” in this section for fur- ther information.


To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons on the driver’s seat during a recall (S, 1, or 2), or pressing any one of the power seat buttons, pressing the adjustable pedals button, or pressing either the LOCK or UNLOCK button on the RKE transmitter


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
when not in the ignition switch. When a recall is can- celled, the driver’s seat and the pedals stop moving. A delay of one second will occur before another recall can be selected. NOTE: A chime sound may be heard if setting memory was inhibited for any reason. To Disable a RKE Transmitter Linked to Memory


1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release the memory SET button located on the driver’s seat. 3. Within 10 seconds, press and release the UNLOCK button on the RKE transmitter. To disable another RKE transmitter linked to either memory position, repeat Steps 1-3 for each RKE trans- mitter.


112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The capability to link RKE transmitters to memory is enabled when delivered from the factory. The capability to link RKE transmitters to memory can be disabled (or later re-enabled) by an authorized dealer. For vehicles equipped with the Electronic vehicle Informa- tion Center (EVIC), refer to “Electronic Vehicle Informa- tion Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Self-Limiting Control The memory system includes a self-limiting control for full travel positioning of power seat and adjustable pedal movement (all directions). This self-limiting control may, however, develop an unintended movement limitation if an obstruction is encountered sometime during usage. One example of such an occurrence may include a box or package obstructing the full rearward movement of the driver’s seat. Once the obstruction is removed, the self- limiting control may store a new maximum position. the


self-limiting control may be reset by reaching the new stored position, then press and release MEMORY button 1 or 2. Continued seat travel beyond the new stored position will indicate the self-limiting control has been reset. Driver Easy Exit and Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearward approximately 2.5 in (60 mm) when the key is removed from the ignition switch. The seat will move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position. Each stored memory setting will have an associated Easy Exit and Easy Entry position. The Easy Exit and Easy Entry feature may be automatically disabled if the seat is positioned rearward enough and there is no benefit in moving the seat any farther rearward.


NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.


TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113


Hood Release


114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood.


Safety Latch (1500 Series Shown)


CAUTION!


To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.


WARNING!


Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.


LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.


CAUTION!


Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.


Headlight Switch Location


116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights


To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the A (AUTO) position.


Automatic Headlight Position


When the system is on, the Headlight Delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the headlight switch out of the AUTO position.


NOTE: The engine must be running before the head- lights will turn on in the Automatic Mode. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle spe- cific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. If the windshield or SmartBeam™ mirror is re- NOTE: placed, the SmartBeam™ mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To Activate 1. Enable the Automatic High Beams. Refer to “Elec- tronic Vehicle Information Center (EVIC)/Customer- Programmable Features” in “Understanding Your Instru- ment Panel” for further information.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
2. Turn the headlight switch to the AUTO headlight position. 3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. NOTE: This system will not activate until the vehicle is at or above 20 mph (32 km/h). To Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly.


118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition ON. The headlight delay time is programmable on vehicles equipped with an Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features (SETUP)” in “Understanding Your Instrument Panel” for further information. Parking Lights and Panel Lights


To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise to the


parking light symbol. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. Fog Lights — If Equipped The fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control.


Fog Light Switch


The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter. When a door is open and the interior lights are on, rotating the dimmer control all the way left, to the OFF detent, will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to the right until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are required during the day.


Dimmer Control


120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light The cargo lights are turned on by pressing on the cargo button.


Cargo Light Switch


The cargo lights will also turn on for approximately 30 seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature.


Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated right for 10 minutes, the interior lights will automatically turn off. If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is OFF, the exterior lights will automatically turn off. NOTE: Battery saver mode is cancelled if the ignition is ON.


Daytime Running Lights (DRL) (Canada Only and Fleet Vehicles) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn OFF. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. Multifunction Lever The multifunction lever is located on the left side of the steering column.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121


Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.


Turn Signal Lever


that


it would suggest


122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective. Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released.


High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off.


High/Low Beam Switch


WINDSHIELD WIPERS AND WASHERS


Windshield Wipers The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123


Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the low continual speed position. The delay can be regulated from a maximum of about 18 seconds between cycles, to a cycle every two seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km/h) or less.


Windshield Wiper/Washer Switch


124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed until the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed for a period greater than one second while in the off position, the wiper will cycle approximately three times after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.


WARNING!


Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.


Mist Feature Push the washer knob, located on the end of the multi- function lever, inward to the first detent. The wipers will cycle one time and automatically shut off to clear road mist or spray from a passing vehicle.


TILT STEERING COLUMN the steering column This feature allows you to tilt upward or downward. The tilt lever is located on the steering column, below the multifunction lever.


Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place.


Tilt Steering Lever


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125


WARNING!


Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.


HEATED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 58 to 70 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.


126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch bank below the climate controls.


Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator.


wheel to operate.


NOTE: • The engine must be running for the heated steering • The heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in Section 4 for further information.


WARNING!


• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the steering wheel heater. It may cause burns even at low temperatures, espe- cially if used for long periods. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or cush- ion. This may cause the steering wheel heater to overheat.


DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment


1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left side of the steering column, in the direction you desire the pedals to move.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127


Adjustable Pedals Switch


NOTE: The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.


ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel.


128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION!


Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.


WARNING!


Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked.


Electronic Speed Control Lever


In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once and the cruise indicator light (located in the mes- sage window of the cluster) will illuminate showing that the Electronic Speed Control system is on. To turn the Electronic Speed Control system off, push the ON/OFF button a second time and both the Electronic Speed Control system and indicator will turn off.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129


WARNING!


Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.


To Set a Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed.


130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deacti- vate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. To Resume Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME ACCEL) upwards and release. Resume can be used at any speed above 30 mph (50 km/h). Varying The Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the


RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. lever RESUME Raising the Electronic Speed Control ACCEL upwards once will result in a 1 mph (1 km/h) speed increase. Each time the lever is tapped upward speed increases, so tapping the lever three times will increase speed by 3 mph (5 km/h), etc. To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the Electronic Speed Control lever SET DECEL downward once will result in a 1 mph (1 km/h) speed decrease. Each time the lever is tapped downward, speed decreases.


To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131


WARNING!


Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.


132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED The ParkSense威 Rear Park Assist system provides visual and audible indications of the distance between the rear bumper and the detected obstacle when backing up. Refer to ParkSense威 System Usage and Precautions for limitations of this system and recommendations. ParkSense威 will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. ParkSense威 can be active only when the shift lever is in REVERSE. If ParkSense威 is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h).


ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear bumper in the horizontal direction, depending on the location, type and orientation of the obstacle. ParkSense姞 Warning Display The ParkSense威 Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features) (SETUP)” in “Understanding Your Instrument Panel” for further information.


The ParkSense威 Warning Display is located in the instru- ment cluster’s EVIC display. It provides both visual and audible warnings to indicate the distance between the rear bumper and the detected obstacle.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.


Rear ParkSense威 Display


Rear Park Assist On


134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


Rear Park Assist Disabled


ParkSense威 will indicate a detected obstacle by showing three solid arcs and will produce a 1⁄2 second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.


Slow Tone


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135


Fast Tone


Continuous Tone


The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.


136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES


DISPLAY MESSAGE


OBSTACLE DISTANCE FROM:


ARC’s


REAR CORNERS


REAR CENTER


Park Assist ON


Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected


27.5 in (70 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)


78.7 in (200 cm) 39.3 in (100 cm) 31.4 in (80 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)


None 3 Solid


3 Flashing 3 Flashing 2 Flashing 2 Flashing 2 Flashing 1 Flashing


AUDIBLE SIG-


NAL None


Yes, 1/2 second


Slow Tone Slow Tone Fast Tone Fast Tone Fast Tone


Continuous Tone


NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.


Enable/Disable ParkSense姞 ParkSense威 can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display. Refer to “Electronic Vehicle Informa- tion Center (Customer- Programmable Features (SETUP)” in “Understanding Your Instrument Panel” for further information.


(EVIC)/Personal


Settings


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137


Park Assist Switch


When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DIS- ABLED” message for approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further in- formation. When the shift lever is moved to REVERSE


138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and the system is disabled, the EVIC will display the “PARK ASSIST DISABLED” message for as long as the vehicle is in REVERSE. The switch LED will be ON when ParkSense威 is disabled or defective. The switch LED will be OFF when Park- Sense威 is enabled. Service ParkSense姞 When the ParkSense威 Rear Park Assist system is mal- functioning, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “CLEAN PARK ASSIST SENSORS” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Un- derstanding Your Instrument Panel” for further informa- tion. When the shift lever is moved to REVERSE and the system has detected a faulted condition, the EVIC will display the “CLEAN PARK ASSIST SENSORS” message for as long as the vehicle is in REVERSE. Under this condition ParkSense威 will not operate.


If “CLEAN PARK ASSIST SENSORS” appears in the Electronic Vehicle Information Center (EVIC) after mak- ing sure the rear bumper is clean and free of snow, ice, mud, or other debris, see your authorized dealer. Cleaning ParkSense姞 Clean the ParkSense威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. ParkSense姞 System Usage and Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the ParkSense威 Rear Park Assist system oper- ating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the ParkSense威 Rear Park Assist system.


• When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Further- more, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, the instrument cluster will display “PARK ASSIST DISABLED” mes- sage for as long as the vehicle is in reverse. • ParkSense威, when on, will MUTE the radio when it is • If a ParkSense威 system malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “CLEAN PARK ASSIST SENSORS” and the LED in the ParkSense威 switch will illuminate. If this message continues to appear in the Electronic Vehicle


sounding a tone.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
Information Center (EVIC) after making sure the rear bumper is clean and free of snow, ice, mud, or other debris, see your authorized dealer. • Clean the ParkSense威 sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the system not working properly. The ParkSense威 system might not detect an obstacle behind the bumper, or it could provide a false indication that an obstacle is behind the bumper. • Objects must not be within 12 in (30 cm) from the rear bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “CLEAN PARK ASSIST SENSORS” message to be displayed in the instrument cluster.


140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION!


• The ParkSense威 Rear Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the Park- Sense威 sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the ParkSense威 Rear Park Assist system to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense威.


WARNING!


• Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.


(Continued)


WARNING! (Continued)


• Before using the ParkSense威 Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear bumper when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the ParkSense威 sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141


PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen. The Park- View威 camera is located next to the tailgate handle on the rear of the vehicle.


WARNING!


Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.


142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION!


• To avoid vehicle damage, ParkView威 should only be used as a parking aid. The ParkView威 camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/ her shoulder when using ParkView威.


If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens.


Turning ParkView姞 On or Off — With Navigation/Multimedia Radio


1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again.


Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio


1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.


OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the review mirror. The overhead console contains the following features:


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143


• Courtesy/Reading Lights • Power Sunroof Switch — If Equipped • Power Sliding Rear Window Switch — If Equipped • Universal Garage Door Opener — If Equipped


Overhead Console


144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.


Front Courtesy/Reading Lights


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145
NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned OFF, they will extinguish after 15 minutes.


GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery.


Rear Passenger Courtesy/Reading Light


146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons are located in the overhead console, and contain one, two or three dots/lines desig- nating the different HomeLink威 channels.


HomeLink威 Buttons


NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.


WARNING!


• Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety infor- mation or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.


Programming HomeLink姞


Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20 seconds. The EVIC will display “CLEARING CHAN- NELS”. Release the buttons when the EVIC message states “CHANNELS CLEARED”. It is recommended that a new battery be placed in the the device being copied to handheld transmitter of HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. It is also advised to park outside the garage while training. 1. Turn the ignition switch to the ON/RUN position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147
2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”. Then release both the HomeLink威 and handheld trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the handheld transmitter. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train.


148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT”. If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.


This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).


1 — Garage Door Opener 2 — Training Button


6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149


Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has


150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, press the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps:


and release


1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.” Note that all channels will be erased. Indi- vidual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.


Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the garage door opener to • Did you unplug the device for training, and remember


complete the training for rolling code.


to plug it back in?


If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151


General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met.


152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights.


Power Sunroof Switch


NOTE: The Power Accessory Delay feature will allow the power sunroof to operate for approximately ten minutes after the ignition is turned OFF or until a front door is opened.


WARNING!


• Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. do not leave the key in the ignition. A child could operate power win- dows, other controls, or move the vehicle. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.


Open Sunroof — Express Mode Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the Express Open Feature. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153
sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙Vent⬙ button and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof. To close the sunroof from the vented position, press forward on the sunroof switch.


154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.


Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.


ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power. The battery symbol indicates that the outlet is connected to the battery, and can provide power at all times.


element must be used.


NOTE: • To ensure proper operation a MOPAR威 knob and • Do not exceed the maximum power of 160 Watts (13
Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.


The auxiliary power outlets can be found in the following locations: • Lower left and lower right of the center stack — • Inside the top storage tray — with floor mounted


without floor mounted shifter.


shifter.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155


Power Outlet — Floor Shifter


156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


• Inside the upper lid of the center storage compartment


— if equipped.


• Rear of the center console storage compartment —


Power Outlet — Upper Lid


Quad Cab威 or Crew Cab.


Power Outlet — Rear Center Console


The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posi- tions.


All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge.


WARNING!


To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an


the vehicle.


electric shock and failure.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157


CAUTION!


• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.


158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.


Ash Receiver and Cigar Lighter (Bench Seat)


1 — Cigar Lighter 2 — Ash Receiver


For vehicles equipped with an optional floor shifter.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159


POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150
Watts. Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed this power limit, as will most power tools.


Optional Floor Shifter


1 — Cigar Lighter 2 — Ash Receiver


160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once

Loading...
x