2010 Dodge RAM Owners Manual

works on your vehicle that it has an airbag system. (Continued)

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued)

• Do not attempt to modify any part of your ad- vanced airbag system. The airbag may inflate accidentally or may not function properly if modi- fications are made. Take your vehicle to an autho- rized dealer for any advanced airbag system ser- vice. If your seat, including your trim cover and cushion, needs to be serviced in any way (includ- ing removal or loosening/tightening of seat attach- ment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accesso- ries may be used. If it is necessary to modify an advanced airbag system for persons with disabili- ties, contact your authorized dealer.

Airbag Warning Light

You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately. • The Airbag Warning Light does not come on for approximately six to eight seconds when the ignition switch is first turned ON. • The light remains on after the approximate four to • The light comes on and remains on while driving. If the speedometer, tachometer, or any engine NOTE: related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label

six-second interval.

located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data param- eters (see list below) in an event data recorder prior to the moment of airbag deployment, or near deployment (if applicable), and up to a quarter second of either high- speed deceleration data or change in velocity during and/or after airbag deployment or near-deployment. EDR data is ONLY recorded if an airbag deploys, or nearly deploys, and is otherwise unavailable. NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indica- tive of a crash, but not severe enough to warrant airbag deployment.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63
2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by Chrysler Group LLC and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash investigations initiated by Chrysler Group LLC, such investigations may be re- quested by customers, insurance carriers, government officials, and professional crash researchers, such as those associated with universities, and with hospital and insur- ance organizations. In the event that an investigation is undertaken by Chrysler Group LLC (regardless of initiative), the com- pany or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. govern- ment and various states. Data of a potentially sensitive nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by Chrysler Group LLC to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved. 2. Used in defense of litigation involving a Chrysler Group LLC product.

3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • Vehicle speed • Engine RPM • Brake switch status • Pedal position • And other parameters depending

on vehicle

configuration Child Restraint Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the

United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.

WARNING!

In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

experts

recommend that

Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child. • Safety

children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt. • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat

cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.

For

additional

information,

NOTE: to www.seatcheck.org or call 1–866–SEATCHECK. Cana- dian residents, should refer to Transport Canada’s web- site for additional information. http://www.tc.gc.ca/ roadsafety/safedrivers/childsafety/index.htm

refer

WARNING!

• Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward-facing child restraint should only be

used in a rear seat.

Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67
from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.

restraint manufacturer’s directions.

68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.

Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Quad Cab威, Mega Cab威 and Crew Cab rear seat outboard positions. LATCH equipped seating positions feature both lower anchor bars, located at the back of the seat cushion, and tether strap anchorages, located behind the seat back (refer to “Child Restraint Tether Anchor”).

Quad Cab威/Mega Cab威/Crew Cab Rear Outboard Seats

Driver Side

Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for

some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. NOTE: • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69
of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. • If your child restraint seat is not LATCH-compatible,

install the restraint using the vehicle seat belting.

70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System

WARNING!

Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab威, Mega Cab威 or Crew Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab威, Mega Cab威 or Crew Cab model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury.

rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system.

We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector, and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some

WARNING!

Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71
the lap portion around the child restraint. Any seat belt system will loosen with time, so check the belt occasion- ally, and pull it tight if necessary. Child Restraint Tether Anchor Child restraints having tether straps and hooks for con- nection to tether anchors have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for their older products. Regular Cab models have two tether anchorages, one each behind the front center and right seats. Quad Cab威, Mega Cab威 and Crew Cab models have three anchor- ages, one behind each of the rear seats.

Installing Child Restraints Using the Vehicle Seat Belt The seat belts in the passenger seating positions are equipped with either an Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR will make a ratcheting noise if you extract the entire belt from the retractor and then allow the belt to retract into the retractor. For additional information on ALR, refer to “Automatic Locking Mode”. To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle. Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor. Finally, pull on any excess webbing to tighten

72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions.

An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your authorized dealer for help if necessary.

Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.

Regular Cab Tether Strap Mounting

1 — Tether Strap Hook 2 — Tether Strap to Child Restraint 3 — Tether Anchor

Multiple Child Restraint Installation Sequence (Quad Cab威/Crew Cab/Mega Cab威 - Rear Seats) Quad Cab威/Mega Cab威 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73

Head Restraint Adjustment

2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and then to the anchor directly behind the center rear seat. 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat.

74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufactur- er’s instructions.

Multiple Child Restraint Quad Cab威/Mega Cab威

1 — Inner Anchor Strap Ring(s) 2 — Snap Hook 3 — Tether Strap 4 — Passenger’s Side Rear Child Seat 5 — Rear Center Child Seat 6 — Driver’s Side Rear Child Seat

Crew Cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by raising the head re- straint and reaching between the rear glass and rear seat.

Head Restraint Adjustment

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75
2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint, through the outboard tether strap loop, then route it to the tether strap loop located directly behind the center rear seat. 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap through the tether strap loop behind the center seat, and attach the hooks to the anchor located directly behind the center rear seat located under a plastic cover. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint through the center seat tether strap loop and anchor to the tether strap loop located behind either outboard seating positions.

76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufactur- er’s instructions. Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug • Check belt fit periodically. A child’s squirming or

as possible.

slouching can move the belt out of position.

If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.

Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.

ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided.

The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your Ve- hicle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not inter- preted as an indication of difficulty.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77

SAFETY TIPS

Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and

using a seat belt properly.

78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips:

Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.

If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.

Safety Checks You Should Make Inside the Vehicle

Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79

Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer is inoperable. Periodic Safety Checks You Should Make Outside the Vehicle

for service if your defroster

Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.

80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS

䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87
▫ Automatic Dimming Mirror —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 88
▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 88
▫ Outside Mirrors Folding Feature . . . . . . . . . . 89
▫ Power Mirrors — If Equipped . . . . . . . . . . . . 90
▫ Heated Mirrors — If Equipped . . . . . . . . . . . . 91
▫ Driver’s Automatic Dimming Mirror —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 91

▫ Illuminated Vanity Mirror — If Equipped . . . . 92
▫ “Slide-On-Rod” Features Of Sun Visor —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 92
▫ Trailer Towing Mirrors — If Equipped . . . . . . 93
䡵 Uconnect™ phone — If Equipped . . . . . . . . . . . 94
䡵 Voice Command — If Equipped . . . . . . . . . . . . 94
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
▫ Manual Seat Adjuster — If Equipped . . . . . . . 95
▫ Manual Reclining Seats — If Equipped . . . . . . 96

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫ Adjustable Head Restraints . . . . . . . . . . . . . . 97
▫ Eight-Way Power Seats — If Equipped . . . . . 100
▫ Power Lumbar — If Equipped . . . . . . . . . . . 101
▫ Heated Seats — If Equipped . . . . . . . . . . . . 102
▫ Ventilated Seats — If Equipped . . . . . . . . . . 104
▫ 40-20-40 Front Bench Seat — If Equipped . . . 104
▫ Mega Cab威 Rear Seat Features . . . . . . . . . . . 105
䡵 Driver Memory Seat — If Equipped . . . . . . . . 108

▫ Setting Memory Positions And Linking RKE

Transmitter To Memory . . . . . . . . . . . . . . . . 109
▫ Memory Position Recall . . . . . . . . . . . . . . . . 110
▫ To Disable a RKE Transmitter Linked To

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
▫ Self-Limiting Control . . . . . . . . . . . . . . . . . . 112

▫ Driver Easy Exit And Easy Entry Control

. . . 112
䡵 To Open And Close The Hood . . . . . . . . . . . . 113
䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 116
▫ Automatic Headlights — If Equipped . . . . . . 116
▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 117
▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . 118
▫ Parking Lights And Panel Lights . . . . . . . . . 118
▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 118
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 119
▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . 120
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 120
▫ Battery Saver . . . . . . . . . . . . . . . . . . . . . . . 120

▫ Daytime Running Lights (DRL)

▫ Multifunction Lever

䡵 Windshield Wipers And Washers

(Canada Only And Fleet Vehicles) . . . . . . . . . 121
. . . . . . . . . . . . . . . . . . 121
. . . . . . . . . . 123
▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . 123
▫ Windshield Washers . . . . . . . . . . . . . . . . . . 124
▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 124
䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . 124
䡵 Heated Steering Wheel — If Equipped . . . . . . 125
䡵 Driver Adjustable Pedals — If Equipped . . . . . 127
. . . . . . . . . . . . . . . . . . . . . . . . 127
䡵 Electronic Speed Control — If Equipped . . . . . 128
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 129

▫ Adjustment

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 129
▫ Deactivating Electronic Speed Control . . . . . . 130
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 130
▫ Varying The Speed Setting . . . . . . . . . . . . . . 130
▫ To Accelerate For Passing . . . . . . . . . . . . . . 131
䡵 Parksense威 Rear Park Assist — If Equipped . . . 132
▫ Parksense威 Sensors . . . . . . . . . . . . . . . . . . . 132
▫ Parksense威 Warning Display . . . . . . . . . . . . 132
▫ Enable/Disable Parksense威 . . . . . . . . . . . . . 137
▫ Service Parksense威 . . . . . . . . . . . . . . . . . . . 138
▫ Cleaning Parksense威 . . . . . . . . . . . . . . . . . . 138
▫ Parksense威 System Usage

And Precautions . . . . . . . . . . . . . . . . . . . . . 138

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Parkview威 Rear Back Up Camera —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 141
▫ Turning Parkview威 On Or Off —

With Navigation/Multimedia Radio . . . . . . . 142

▫ Turning Parkview威 On Or Off —

▫ Courtesy/Reading Lights

Without Navigation/Multimedia Radio . . . . . 143
䡵 Overhead Console — If Equipped . . . . . . . . . . 143
. . . . . . . . . . . . . . 144
䡵 Garage Door Opener — If Equipped . . . . . . . . 145
▫ Programming HomeLink威 . . . . . . . . . . . . . . 147
▫ Gate Operator/Canadian Programming . . . . 149
▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 150
▫ Reprogramming A Single HomeLink威

Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 151
▫ General Information . . . . . . . . . . . . . . . . . . 151
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 152
▫ Open Sunroof — Express Mode . . . . . . . . . . 153
▫ Closing Sunroof — Express . . . . . . . . . . . . . 153
▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 153
▫ Pinch Protect Override . . . . . . . . . . . . . . . . 153
▫ Venting Sunroof — Express . . . . . . . . . . . . . 153
▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 154
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 154
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 154
▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 154

䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 154
䡵 Cigar Lighter And Ash Receiver —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 158
䡵 Power Inverter — If Equipped . . . . . . . . . . . . 159
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 161

▫ Front Instrument Panel Cupholders —

(40–20–40 Seats)

. . . . . . . . . . . . . . . . . . . . . 161

▫ Front Instrument Panel Cupholders —

Floor Mounted Shifter . . . . . . . . . . . . . . . . . 162
▫ Rear Cupholder — Quad Cab威 . . . . . . . . . . 162
▫ Rear Cupholder — Crew Cab . . . . . . . . . . . 163
䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
▫ Glove Box Storage . . . . . . . . . . . . . . . . . . . 163
▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 165

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
▫ Center Storage Compartment —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 166

▫ Second Row In-Floor Storage Bin —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 168
▫ Seatback Storage . . . . . . . . . . . . . . . . . . . . . 169
▫ Storage (Regular Cab) . . . . . . . . . . . . . . . . . 169
▫ Storage And Seats (Crew Cab) . . . . . . . . . . . 170
▫ Plastic Grocery Bag Retainers

(Regular Cab Models)

. . . . . . . . . . . . . . . . . 170
䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 171
▫ Rear Window Defroster . . . . . . . . . . . . . . . . 171
▫ Power Sliding Rear Window —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 172

▫ Manual Sliding Rear Window —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 172

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Fold Flat Load Floor — If Equipped . . . . . . . . 173
䡵 Rambox威 — If Equipped . . . . . . . . . . . . . . . . 175

▫ Rambox威 Integrated Box Side

Storage Bins . . . . . . . . . . . . . . . . . . . . . . . . 176
▫ Rambox威 Safety Warning . . . . . . . . . . . . . . . 179
▫ Bed Extender — If Equipped . . . . . . . . . . . . 180
▫ Bed Rail Tie-Down System . . . . . . . . . . . . . . 187

䡵 Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . 189
▫ Camper Applications . . . . . . . . . . . . . . . . . . 189
䡵 Easy-Off Tailgate . . . . . . . . . . . . . . . . . . . . . . 189

▫ Disconnecting The Rear Camera —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 189
▫ Removing The Tailgate . . . . . . . . . . . . . . . . 190
▫ Locking Tailgate — If Equipped . . . . . . . . . . 191

MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

Adjusting Rearview Mirror

The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror should be adjusted to center on the view through the rear window.

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the power button at the base of the mirror. A light next to the button will illuminate when the dimming feature is activated.

CAUTION!

To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.

Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.

Automatic Dimming Mirror

WARNING!

Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex right side mirror.

Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

Folding Mirror

CAUTION!

It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location.

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel.

The power mirror controls consist of mirror select but- tons and a four-way mirror control switch.

Power Mirror Controls

Power Mirror Controls

1 — Mirror Select Buttons 2 — Mirror Control

To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

Heated Mirrors — If Equipped

These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Driver’s Automatic Dimming Mirror — If Equipped The driver’s outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirror will automatically adjust for headlight glare when the inside mirror adjusts.

Power Mirror Movement

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover turns off the light.

“Slide-On-Rod” Features of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the “Slide-On-Rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide-On-Rod” until the sun visor is in the desired position.

Illuminated Vanity Mirror

Slide-On-Rod Extender

Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is located next to main mirror and can be adjusted separately.

Trailer Towing Position

Blindspot Mirror

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED

Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.

VOICE COMMAND — IF EQUIPPED Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details.

SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. Proper use of the seats is needed for safe operation of the vehicle.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and

using a seat belt properly.

Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat. Pull up on the handle and slide the seat forward or backward to move the seat into the most comfortable position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

Manual Seat Adjuster

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.

Manual Reclining Seats — If Equipped The recliner handle is located on the outside of the seat cushion and is used to adjust the seatback position. To adjust the seatback, lift upward on the handle, lean back on the seatback and release the handle at the desired position. To return the seatback, lift upward on the handle, lean forward and release the handle at the desired position.

Recline Handle

WARNING!

• Actuating the recliner handle will allow the seat- back to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin behind the seat. To avoid injury, place your hand on the seatback and actuate the handle then posi- tion the seatback in the desired position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

WARNING! (Continued)

• You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.

(Continued)

Adjustable Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear.

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint.

To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint.

Adjusting Head Restraint

Removing Head Restraint

To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest

until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle.

WARNING!

Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK.

Rear Head Restraints The outboard head restraints can be adjusted. To raise the head restraint, pull upward on the head restraint. To

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint.

Adjustable Rear Head Restraints

NOTE: The rear center head restraint (Crew Cab only) is fixed and cannot be adjusted.

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback to position yourself in the most comfortable driving position. Push forward or rearward on the switch and the seatback will move in either direction.

Power Seat Switches

1 — Power Seat Switch 2 — Power Seatback Switch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101

Power Lumbar — If Equipped The lumbar controls are located on the outboard side of the seat cushion. The lumbar support can be increased by pressing the front of the switch and decreased by press- ing the back of the switch.

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.

CAUTION!

DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.

Lumbar Control Switch

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.

Heated Seats — If Equipped Both front seats and rear passenger seats can be equipped with heaters. The switches for the front seats are located in the instrument panel under the climate controls. The switches for the rear passenger seats are located on the back of the center console. After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.

Press the switch once to select High- level heating. Press the switch a sec- ond time to select Low-level heating. Press the switch a third time to shut the heating elements Off.

NOTE: The engine must be running for the heated seats to operate. The heated seats switch from High to Low and from Low to Off automatically, based on time and temperature of the seat. The heated seats can operate on High heat for as little as 4 minutes and up to 30 minutes before switching to Low heat. Once a seat has switched to the Low heat setting it may operate for an additional 60 minutes before automatically shutting Off. The heated seats can shut Off early or may not turn on when the seat is already warm.

NOTE: The drivers heated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information.

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103

WARNING! (Continued)

• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.

CAUTION!

Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat.

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ventilated Seats — If Equipped Located in the seat cushion and seatback are small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compart- ment. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering to help keep the driver cooler in higher ambient tempera- tures. The ventilated seat switches are located in the switch bank in the center stack of the instrument panel, just below the climate controls. The fans operate at two speeds, High and Low.

Press the switch once to choose High, press it a second time to choose Low. Pressing the switch a third time will turn the ventilated seat Off. When High speed is selected both lights on

the switch will be illuminated. When Low speed is selected one light will be illuminated. NOTE: • The engine must be running for the ventilated seats to • The drivers ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information.

operate.

40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).

Mega Cab姞 Rear Seat Features

Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion. Pull upward on the handle, to release the seatback, and lean forward or rearward to the desired position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105

WARNING!

Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.

Rear Seat Recliner Handle

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint.

2. Fold the seatback forward.

Table Mode Handle

Table Mode

3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place. Folding Rear Seat — If Equipped Both the left and right rear seats will drop and move forward when the seatback is folded flat.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and • Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop and strike someone in the vehicle, causing serious injury or possible death.

using a seat belt properly.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107

To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats.

Handle

108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down and push the seat forward.

Rear Passenger Fold Flat Seats

3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place.

WARNING!

Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.

DRIVER MEMORY SEAT — IF EQUIPPED The memory seat buttons are located on the outboard side of the drivers seat cushion.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to two RKE transmitters, each RKE transmitter linked to either of the two memory positions. Setting Memory Positions and Linking RKE Transmitter to Memory

NOTE: Each time the S (SET) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 1. Turn the vehicle key to the ON/RUN position.

Memory Seat Buttons

The memory buttons 1 and 2 can be programmed to recall the driver’s seat position, driver’s outside mirror position, adjustable brake, accelerator pedals position, Automatic Temperature Control (ATC) temperature set- ting and radio station preset settings. Your Remote

110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust the driver’s seat, recliner, and both sideview mirrors to the desired positions. NOTE: Not all motors may be moved at one time. Refer to “Seats/Eight-Way Power Seat” in this section for further information. 3. Adjust the brake and accelerator pedals to the desired positions. 4. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 5. Adjust while the ATC is in Auto mode. 6. Press and release the SET button located on the driver’s seat. 7. Within five seconds, press and release MEMORY button 1 or 2 on the driver’s seat. The next steps must be

the Automatic Temperature Control (ATC)

performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 8. Turn the ignition OFF and remove the key. 9. Press and release the LOCK button on one of the RKE transmitters. 10. Repeat the above steps to set the next memory position using the other numbered memory button or to link another RKE transmitter to memory. NOTE: A chime sound may be heard if Setting Memory was inhibited for any reason. Memory Position Recall NOTE: • The vehicle must be in PARK to recall memory posi-

tions.

• Not all motors may be moved at one time. Refer to the “Seats/Eight-Way Power Seat” in this section for fur- ther information.

To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons on the driver’s seat during a recall (S, 1, or 2), or pressing any one of the power seat buttons, pressing the adjustable pedals button, or pressing either the LOCK or UNLOCK button on the RKE transmitter

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
when not in the ignition switch. When a recall is can- celled, the driver’s seat and the pedals stop moving. A delay of one second will occur before another recall can be selected. NOTE: A chime sound may be heard if setting memory was inhibited for any reason. To Disable a RKE Transmitter Linked to Memory

1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release the memory SET button located on the driver’s seat. 3. Within 10 seconds, press and release the UNLOCK button on the RKE transmitter. To disable another RKE transmitter linked to either memory position, repeat Steps 1-3 for each RKE trans- mitter.

112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The capability to link RKE transmitters to memory is enabled when delivered from the factory. The capability to link RKE transmitters to memory can be disabled (or later re-enabled) by an authorized dealer. For vehicles equipped with the Electronic vehicle Informa- tion Center (EVIC), refer to “Electronic Vehicle Informa- tion Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Self-Limiting Control The memory system includes a self-limiting control for full travel positioning of power seat and adjustable pedal movement (all directions). This self-limiting control may, however, develop an unintended movement limitation if an obstruction is encountered sometime during usage. One example of such an occurrence may include a box or package obstructing the full rearward movement of the driver’s seat. Once the obstruction is removed, the self- limiting control may store a new maximum position. the

self-limiting control may be reset by reaching the new stored position, then press and release MEMORY button 1 or 2. Continued seat travel beyond the new stored position will indicate the self-limiting control has been reset. Driver Easy Exit and Easy Entry Control This additional feature provides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearward approximately 2.5 in (60 mm) when the key is removed from the ignition switch. The seat will move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position. Each stored memory setting will have an associated Easy Exit and Easy Entry position. The Easy Exit and Easy Entry feature may be automatically disabled if the seat is positioned rearward enough and there is no benefit in moving the seat any farther rearward.

NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113

Hood Release

114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to release it, before raising the hood.

Safety Latch (1500 Series Shown)

CAUTION!

To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.

WARNING!

Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.

LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.

CAUTION!

Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.

Headlight Switch Location

116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights

To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the A (AUTO) position.

Automatic Headlight Position

When the system is on, the Headlight Delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the headlight switch out of the AUTO position.

NOTE: The engine must be running before the head- lights will turn on in the Automatic Mode. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle spe- cific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. If the windshield or SmartBeam™ mirror is re- NOTE: placed, the SmartBeam™ mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To Activate 1. Enable the Automatic High Beams. Refer to “Elec- tronic Vehicle Information Center (EVIC)/Customer- Programmable Features” in “Understanding Your Instru- ment Panel” for further information.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
2. Turn the headlight switch to the AUTO headlight position. 3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. NOTE: This system will not activate until the vehicle is at or above 20 mph (32 km/h). To Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly.

118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay To aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off. Headlight delay can be cancelled by either turning the headlight switch on then off, or by turning the ignition ON. The headlight delay time is programmable on vehicles equipped with an Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features (SETUP)” in “Understanding Your Instrument Panel” for further information. Parking Lights and Panel Lights

To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise to the

parking light symbol. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. Fog Lights — If Equipped The fog lights are turned on by rotating the headlight switch to the parking light or headlight position and pushing in the headlight rotary control.

Fog Light Switch

The fog lights will operate only when the parking lights are on or when the vehicle headlights are on low beam. An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter. When a door is open and the interior lights are on, rotating the dimmer control all the way left, to the OFF detent, will cause all the interior lights to go out. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the headlights are on you can supplement the brightness of the odometer, trip odom- eter, radio and overhead console by rotating the control to the right until you hear a click. This feature is termed the “Parade” mode and is useful when headlights are required during the day.

Dimmer Control

120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light The cargo lights are turned on by pressing on the cargo button.

Cargo Light Switch

The cargo lights will also turn on for approximately 30 seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature.

Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated right for 10 minutes, the interior lights will automatically turn off. If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is OFF, the exterior lights will automatically turn off. NOTE: Battery saver mode is cancelled if the ignition is ON.

Daytime Running Lights (DRL) (Canada Only and Fleet Vehicles) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn OFF. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. Multifunction Lever The multifunction lever is located on the left side of the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121

Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.

Turn Signal Lever

that

it would suggest

122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective. Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released.

High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off.

High/Low Beam Switch

WINDSHIELD WIPERS AND WASHERS

Windshield Wipers The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123

Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the low continual speed position. The delay can be regulated from a maximum of about 18 seconds between cycles, to a cycle every two seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km/h) or less.

Windshield Wiper/Washer Switch

124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed until the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed for a period greater than one second while in the off position, the wiper will cycle approximately three times after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.

Mist Feature Push the washer knob, located on the end of the multi- function lever, inward to the first detent. The wipers will cycle one time and automatically shut off to clear road mist or spray from a passing vehicle.

TILT STEERING COLUMN the steering column This feature allows you to tilt upward or downward. The tilt lever is located on the steering column, below the multifunction lever.

Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place.

Tilt Steering Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125

WARNING!

Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.

HEATED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel has been turned on it will operate for approximately 58 to 70 minutes before automatically shutting off. The heated steering wheel can shut off early or may not turn on when the steering wheel is already warm.

126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch bank below the climate controls.

Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator.

wheel to operate.

NOTE: • The engine must be running for the heated steering • The heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in Section 4 for further information.

WARNING!

• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the steering wheel heater. It may cause burns even at low temperatures, espe- cially if used for long periods. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or cush- ion. This may cause the steering wheel heater to overheat.

DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment

1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left side of the steering column, in the direction you desire the pedals to move.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127

Adjustable Pedals Switch

NOTE: The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel.

128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.

WARNING!

Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked.

Electronic Speed Control Lever

In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once and the cruise indicator light (located in the mes- sage window of the cluster) will illuminate showing that the Electronic Speed Control system is on. To turn the Electronic Speed Control system off, push the ON/OFF button a second time and both the Electronic Speed Control system and indicator will turn off.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.

To Set a Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed.

130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deacti- vate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. To Resume Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME ACCEL) upwards and release. Resume can be used at any speed above 30 mph (50 km/h). Varying The Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the

RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. lever RESUME Raising the Electronic Speed Control ACCEL upwards once will result in a 1 mph (1 km/h) speed increase. Each time the lever is tapped upward speed increases, so tapping the lever three times will increase speed by 3 mph (5 km/h), etc. To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the Electronic Speed Control lever SET DECEL downward once will result in a 1 mph (1 km/h) speed decrease. Each time the lever is tapped downward, speed decreases.

To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED The ParkSense威 Rear Park Assist system provides visual and audible indications of the distance between the rear bumper and the detected obstacle when backing up. Refer to ParkSense威 System Usage and Precautions for limitations of this system and recommendations. ParkSense威 will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. ParkSense威 can be active only when the shift lever is in REVERSE. If ParkSense威 is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h).

ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear bumper in the horizontal direction, depending on the location, type and orientation of the obstacle. ParkSense姞 Warning Display The ParkSense威 Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features) (SETUP)” in “Understanding Your Instrument Panel” for further information.

The ParkSense威 Warning Display is located in the instru- ment cluster’s EVIC display. It provides both visual and audible warnings to indicate the distance between the rear bumper and the detected obstacle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.

Rear ParkSense威 Display

Rear Park Assist On

134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Park Assist Disabled

ParkSense威 will indicate a detected obstacle by showing three solid arcs and will produce a 1⁄2 second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.

Slow Tone

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

Fast Tone

Continuous Tone

The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.

136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES

DISPLAY MESSAGE

OBSTACLE DISTANCE FROM:

ARC’s

REAR CORNERS

REAR CENTER

Park Assist ON

Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected

27.5 in (70 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)

78.7 in (200 cm) 39.3 in (100 cm) 31.4 in (80 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)

None 3 Solid

3 Flashing 3 Flashing 2 Flashing 2 Flashing 2 Flashing 1 Flashing

AUDIBLE SIG-

NAL None

Yes, 1/2 second

Slow Tone Slow Tone Fast Tone Fast Tone Fast Tone

Continuous Tone

NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.

Enable/Disable ParkSense姞 ParkSense威 can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display. Refer to “Electronic Vehicle Informa- tion Center (Customer- Programmable Features (SETUP)” in “Understanding Your Instrument Panel” for further information.

(EVIC)/Personal

Settings

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

Park Assist Switch

When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DIS- ABLED” message for approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further in- formation. When the shift lever is moved to REVERSE

138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and the system is disabled, the EVIC will display the “PARK ASSIST DISABLED” message for as long as the vehicle is in REVERSE. The switch LED will be ON when ParkSense威 is disabled or defective. The switch LED will be OFF when Park- Sense威 is enabled. Service ParkSense姞 When the ParkSense威 Rear Park Assist system is mal- functioning, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “CLEAN PARK ASSIST SENSORS” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Un- derstanding Your Instrument Panel” for further informa- tion. When the shift lever is moved to REVERSE and the system has detected a faulted condition, the EVIC will display the “CLEAN PARK ASSIST SENSORS” message for as long as the vehicle is in REVERSE. Under this condition ParkSense威 will not operate.

If “CLEAN PARK ASSIST SENSORS” appears in the Electronic Vehicle Information Center (EVIC) after mak- ing sure the rear bumper is clean and free of snow, ice, mud, or other debris, see your authorized dealer. Cleaning ParkSense姞 Clean the ParkSense威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. ParkSense姞 System Usage and Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the ParkSense威 Rear Park Assist system oper- ating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the ParkSense威 Rear Park Assist system.

• When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Further- more, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, the instrument cluster will display “PARK ASSIST DISABLED” mes- sage for as long as the vehicle is in reverse. • ParkSense威, when on, will MUTE the radio when it is • If a ParkSense威 system malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “CLEAN PARK ASSIST SENSORS” and the LED in the ParkSense威 switch will illuminate. If this message continues to appear in the Electronic Vehicle

sounding a tone.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
Information Center (EVIC) after making sure the rear bumper is clean and free of snow, ice, mud, or other debris, see your authorized dealer. • Clean the ParkSense威 sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the system not working properly. The ParkSense威 system might not detect an obstacle behind the bumper, or it could provide a false indication that an obstacle is behind the bumper. • Objects must not be within 12 in (30 cm) from the rear bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “CLEAN PARK ASSIST SENSORS” message to be displayed in the instrument cluster.

140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

• The ParkSense威 Rear Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the Park- Sense威 sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the ParkSense威 Rear Park Assist system to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense威.

WARNING!

• Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.

(Continued)

WARNING! (Continued)

• Before using the ParkSense威 Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear bumper when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the ParkSense威 sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141

PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen. The Park- View威 camera is located next to the tailgate handle on the rear of the vehicle.

WARNING!

Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

• To avoid vehicle damage, ParkView威 should only be used as a parking aid. The ParkView威 camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/ her shoulder when using ParkView威.

If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens.

Turning ParkView姞 On or Off — With Navigation/Multimedia Radio

1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear