Login- Download PDF Manual
-
SECTION
TABLE OF CONTENTS
PAGE
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349
10
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
10
INTRODUCTION
CONTENTS
䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4
䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6
䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 74 INTRODUCTION
INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instruc- tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained techni- cians and genuine Mopar威 parts, and is interested in your satisfaction.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this owner’s manual:
INTRODUCTION 5
6 INTRODUCTION
WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
NOTE:
It is illegal to remove the VIN plate.
VEHICLE MODIFICATIONS / ALTERATIONS
WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
INTRODUCTION 7
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
▫ Ignition Key Removal ▫ Key-In-Ignition Reminder
䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . . . . .11
. . . . . . . . . . . . . . . .12
䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .14
▫ Customer Key Programming . . . . . . . . . . . . . .14
▫ General Information . . . . . . . . . . . . . . . . . . . .15
䡵 Illuminated Entry System . . . . . . . . . . . . . . . . . .15
䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .16▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16
▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .16
▫ Child Protection Door Lock . . . . . . . . . . . . . . .18
䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .19
▫ To Unlock The Doors And Liftgate . . . . . . . . . .20
▫ To Lock The Doors And Liftgate . . . . . . . . . . . .21
▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .21
▫ To Program Transmitters . . . . . . . . . . . . . . . . .21
▫ To Open/Close Power Liftgate — If Equipped . .2210 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
▫ To Turn Off “Flash Lights On Lock/Unlock” . . .22
▫ General Information . . . . . . . . . . . . . . . . . . . .23
▫ Transmitter Battery Service . . . . . . . . . . . . . . .23
䡵 Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . . .24
䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
▫ Power Liftgate — If Equipped . . . . . . . . . . . . .27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .29
䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .30
▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .31
▫ Lap/Shoulder Belt Untwisting Procedure . . . . .37
▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .39
▫ Enhanced Driver Seat Belt Reminder System䡵 Windows
(BeltAlert)
. . . . . . . . . . . . . . . . . . . . . . . . . . .39
▫ Seat Belts And Pregnant Women . . . . . . . . . . . .41
▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .41
▫ Driver And Front Passenger SupplementalRestraint System - Airbag . . . . . . . . . . . . . . . .42
▫ Side Airbags Supplemental Restraint System (SRS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . .48
▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .51
䡵 Engine Break-In Recommendations . . . . . . . . . . .59
䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .60
▫ Safety Checks You Should Make InsideThe Vehicle
. . . . . . . . . . . . . . . . . . . . . . . . . .61
▫ Periodic Safety Checks You Should Make Outside
The Vehicle
. . . . . . . . . . . . . . . . . . . . . . . . . .62
A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, then remove the key.
The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45
seconds after the ignition switch has been turned off. Opening either front door will cancel this feature.WARNING!
Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
CAUTION!
An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.
Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition switch, a chime will sound to remind you to remove the key.
SENTRY KEY The Sentry Key Immobilizer System prevents unautho- rized operation of the vehicle by disabling the engine. The system will shut the engine off after 2 seconds of running if an invalid key is used to start the vehicle. This system utilizes ignition keys which have an electronic
chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the Theft Alarm/ Immobilizer Light will come on for three (3) seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics. If the bulb begins to flash after the bulb check, this indicates that an invalid key has been used to start the vehicle. Both of these conditions will result in the engine being shut off after two (2) seconds of running. Keep in mind that a key which has not been programmed is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
If the Theft Alarm/Immobilizer Light comes on during normal vehicle operation (vehicle has been running for longer than 10 seconds), a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transpon- der) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys
NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed.
NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer. Customer Key Programming You can program new sentry keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. 3. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds a chime will sound and the Theft Alarm Light will begin to flash. Turn the ignition switch OFF and remove the second key.
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10
seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. The Keyless Entry Transmitter will also be programmed during this procedure. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details. If a programmed key has been lost, see your NOTE: dealer to have all remaining keys erased from the sys- tems memory. The remaining keys must then repro- grammed. This will prevent the lost key from starting your vehicle. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed.THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
General Information The Sentry Key system complies with FCC rules part 15
and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undes- ired operation.ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned on. NOTE: The overhead console, door courtesy, liftgate and reading lights will not operate if the dimmer control is in the “defeat” position (extreme downward position).
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
DOOR LOCKS
Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel.
If the lock knob is up when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.
WARNING!
• For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe per- sonal injuries and death.
Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
Automatic Door Locks The doors will lock automatically on vehicles with power door locks if: 1. The Auto Lock feature is enabled, 2. the transmission is in gear, 3. all doors are closed 4. the vehicle speed is above 15 mph (24 km/h) and 5. the doors were not previously locked using the power door lock switch or remote keyless entry transmitter. The Automatic Door Locks can be enabled or disabled by performing the procedure in the Electronic Vehicle Infor- mation Center (EVIC), Customer Programmable Features section.
If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as a reminder to remove the key.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled, 2. the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h), 3. the transmission is in NEUTRAL or PARK, 4. the driver door is opened (excluding liftgate), 5. the doors were not previously unlocked and 6. the vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled by performing the procedure in the Electronic Vehicle Infor- mation Center (EVIC), Customer Programmable Features section.
NOTE: Use the Auto Door Locks and Auto Unlock features in accordance with local laws. Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system.
WARNING!
Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position.
When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors and liftgate, and activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio trans- mitter. The transmitter need not be pointed at the vehicle to activate the system.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
If the key is in the ignition switch, then all NOTE: buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of PARK, all the transmitter buttons are disabled for all keys.
To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors and liftgate. The illuminated entry system also turns on. If desired, the “Remote Unlock Driver’s Door NOTE: 1st” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Ve- hicle Information Center (EVIC)” section or by following these steps. 1. Press the UNLOCK button for 4 to 10 seconds. 2. While the UNLOCK button is pressed, (after 4 sec- onds) press the LOCK button. Release both buttons. The “Remote Unlock Driver’s Door 1st” feature can be reactivated by repeating this procedure.
To lock the doors and liftgate: Press and release the LOCK button on the transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal. If desired, the “Sound Horn On Lock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Ve- hicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2. While the LOCK button is pressed (after 4 seconds), press the PANIC button. Release both buttons. The “Sound Horn On Lock” feature can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or turn the ignition switch to the ON position. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. To Program Transmitters: Refer to SENTRY KEY “Customer Key Programming.” If you do not have a programmed transmitter, contact your dealer for details.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To Open/Close Power Liftgate — If Equipped Press the LIFTGATE button twice within five seconds to open/close the power liftgate. The liftgate will beep for 2
seconds and then open/close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position. If the liftgate is locked and is not equipped with a powered liftgate, pressing the button will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. The liftgate will re-lock automatically within 10 seconds once the liftgate is closed. To Turn Off “Flash Lights On Lock/Unlock”If desired, the “Flash Lights On Lock/Unlock” NOTE: feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Ve- hicle Information Center (EVIC)” section or by following these steps.
1. Press the LOCK button for 4 to 10 seconds. 2. While the LOCK button is pressed, (after 4 seconds) press the UNLOCK button. Release both buttons. The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. The table below explains the Lamp Flash options.
Function
Which Turn Signal
Lamps
Number of
Flashes
Lock Unlock 1st Press Unlock All Doors Liftgate
All
Driver’s Side
All
All
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
Transmitter Battery Service The recommended replacement battery is one CR2032
battery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a small screwdriver or similar flat object to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal.General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, snap the two halves together. Make sure there is an even “gap” be- tween the two halves. Test transmitter operation.
VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals. The horn will pulse, headlights/park lights will flash, the Vehicle Theft Alarm/Immobilizer light, located on the instrument panel below the Elec- tronic Vehicle Information Center buttons will flash, and the vehicle will not start. If the alarm is triggered and no action is taken to disarm it, the system will turn off the
horn after three minutes and after 15 minutes of light only operation the system will then rearm itself. To arm the system: Remove the key from the ignition switch and either: 1. Press a power door lock switch while the driver’s or passenger’s door is open. 2. Press the LOCK button on the keyless entry transmit- ter. After the last door is closed, or if all doors are closed, the system will arm itself in about 16 seconds. During that time, the Vehicle Theft Alarm/Immobilizer light will flash. If it does not illuminate, the system is not arming. If you open a door during this arming period, the system will cancel the arming process. You must repeat one of the previously described arming sequences to rearm the system.
To disarm the system: Press the UNLOCK button on the keyless entry transmitter. Also, using a valid sentry key and moving the ignition switch to the ON/START posi- tion will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously, when closing the liftgate. If some- thing has triggered the system in your absence, the horn will sound three times when you disarm the system. Check the vehicle for tampering. NOTE: • The driver’s door key cylinder and the liftgate button on the keyless entry transmitter cannot arm or disarm the system. • Once the alarm is set, and the liftgate button on the keyless entry transmitter is pressed, on a non-power liftgate vehicle, you have a 30 second one time access
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
into the liftgate area. If the liftgate is not opened within 30 seconds the liftgate will automatically re-lock within 10 seconds. • The system remains armed during liftgate entry, press- ing the liftgate button will not disarm the system, if someone enters the vehicle through the liftgate and opens any door the alarm will sound. • When the system is armed, the doors can not be unlocked from the interior power door lock switches. The Vehicle Theft Alarm system is designed to protect your vehicle, however, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the system.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system.
LIFTGATE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. Once unlocked, the liftgate can be opened or closed. To open the liftgate, depress the liftgate release switch located in the exterior handle and pull the liftgate open with one fluid motion.
The liftgate will not manually open if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). NOTE: • If a power malfunction to the power liftgate latch should occur, an emergency liftgate latch release can
be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. • If the liftgate is locked and is not equipped with a powered liftgate, pressing the button on the remote keyless entry transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. The liftgate will re-lock automatically within 10 seconds once the lift- gate is closed.
Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate. Once the liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
The power liftgate may also be opened by pressing the switch located on the overhead console.
A beeping signal will sound two seconds before the liftgate starts to open or close.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.
NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate. Light pressure anywhere along these strips will cause the liftgate to return to the open position.
• The power liftgate must be in the full open position for any of the close buttons to operate. If the liftgate is not fully open, press the open button to fully open the liftgate and then press close. • If the liftgate release switch is activated while the power liftgate is closing, the liftgate will reverse to the full open position. • The power liftgate switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • The power liftgate will not operate in temperatures below ⫺22° F (⫺30° C) or temperatures above 150° F (65° C). Be sure to remove any build-up of snow or ice from the liftgate before pressing any of the power liftgate switches.
• If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually.
WARNING!
• Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29
WINDOWS
Power Windows The window controls on the driver’s door control all the door windows.
There are single window controls on each passenger door trim panel which operate the passenger door windows.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passen- ger windows will be disabled. Auto Down Feature All the power window switches have an auto down feature. Press the window switch to the second detent, release, and the window will go down automatically. To open the window part way, press the window switch to the first detent and release it when you want the window to stop. The power window switches remain active for up to 45
seconds after the ignition switch has been turned off. Opening either front door will cancel this feature.Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, driver inflatable knee blocker and if equipped, left and right side curtain airbags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size seat
belts, your seat belts or the LATCH feature (refer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
WARNING!
In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31
Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
WARNING!
• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
WARNING!
• Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instruc- tions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”.
WARNING!
• A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.
4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35
WARNING!
• A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed.
5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.
Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck. Press the button to release the anchorage, and then move it up or down to the position that serves you best.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
WARNING!
A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
4. Continue to slide the latch plate up until it clears the folded webbing.
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners are designed to work for all size occupants. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the front airbag con- trol module (see Airbag Section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and preten- sioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39
Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60
seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96
seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reacti- vated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8
km/h).40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or RUN position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the OFF position and buckle the driver’s seat belt. 2. Turn the ignition key to the RUN position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled.
NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltA- lert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled.
Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41
Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and stow it.
WARNING!
Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment in low speed collisions. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. This vehicle may also be equipped with a driver inflat- able knee blocker located on the instrument panel below the steering column. This vehicle may also be equipped with left and right side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43
WARNING!
• Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protec- tive covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with left and right side curtain airbags, do not stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions. • If your vehicle is equipped with left and right side curtain airbags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason.
NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Airbags inflate in moderate to high speed impacts. Along with seat belts, and pretensioners, front airbags work with the instrument panel knee blockers to provide improved protection for the driver and front passenger. Left and right side curtain airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe frontal collisions. If your vehicle is equipped, the side curtain airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions where the airbags deploy, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to properly wear the vehicle seat belt (refer to section on Child Restraint) should be secured in the rear seat, in a child restraint or belt-positioning booster seat appropriate for the size and age of the child. Older children who do not use a child restraint or belt-positioning booster seat should ride properly buckled up in the rear seat. Never allow chil- dren to slide the shoulder belt behind them or under their arm.
If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has left and right side curtain airbags, do not lean against the door, airbags will inflate force- fully into the space between you and the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
WARNING!
• Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instru- ment panel during front airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • If the vehicle has left and right side curtain airbags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
sor)
“The Front Airbag System” consists of the following: • Airbag Control Module (with integrated impact sen- • AIRBAG Readiness Light • Driver Airbag • Front Passenger Airbag • Seat Belt Pretensioners • Steering Wheel and Column • Instrument Panel • Seat Belt Readiness Light • Interconnecting Wiring • Passenger Knee Impact Blocker • Driver Inflatable Knee Blocker
How The Airbag Systems Work • The airbag control module determines if an impact is severe enough to require the airbags to inflate. Based on the level of collision severity, the control module determines the proper rate of inflation. The front airbag inflators are designed to provide different rates of airbag inflation. The airbag control module will not detect roll over collisions. The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed under “The Front Airbag System”, except the passenger knee blocker, instru- ment panel and the steering wheel and column. If the key is in the OFF position, in the ACC position, or not in the ignition switch, the front airbags are not on and will not inflate.
The airbag control module sends a message to the instrument cluster to turn on the AIRBAG light in the instrument panel for 6
to 8 seconds when the ignition switch is first turned ON, then turns the light off. If the airbag control module detects a malfunction in any part of the system, the airbag light will turn on either momen- tarily or continuously.WARNING!
Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the airbag control module detects a collision requiring the Front Airbags, it signals the inflator
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47
units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different front airbag inflation rates are possible, these rates are determined by the airbag control module based on collision severity. The front airbag covers separate and fold out of the way as the front airbags inflate to their full size. The front airbags fully inflate in about 50 milliseconds. This is only about half of the time it takes you to blink your eyes. The front airbags then quickly deflate while helping to restrain the driver and front passenger. The driver’s and passenger’s front airbag gas is vented through the airbag material and small vent openings towards the instrument panel. In this way the front airbags do not interfere with your control of the vehicle. • The Supplemental Side Curtain Airbags are designed to activate only in certain side collisions. When the airbag control module detects a collision requiring the side curtain airbags to inflate, it signals the inflators on
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and inflates (in about the same time it takes to blink your eyes). A properly belted and seated occupant is less likely to be injured by the force of the airbag or crash event. Items that are positioned in the area where the side curtain airbag inflates can reduce the effectiveness of the airbag and also increase the likelihood of injuries to the occu- pants, this especially applies to children. The side curtain airbag is about 4 inches (10 cm) thick when it is inflated. • When the airbag control module detects a collision requiring the Driver Inflatable Knee Blocker, it sig- nals the inflator unit. A quantity of nontoxic gas is generated to inflate the Driver Inflatable Knee Blocker. The Driver Inflatable Knee Blocker inflates rearward towards the driver’s knees to help protect the knees
and position you for the best interaction with the front airbag. The Driver Inflatable Knee Blocker fully in- flates in about 50 milliseconds, this is only about half of the time it takes you to blink your eyes. It then quickly deflates while helping to protect the driver’s knees. • The Knee Impact Blockers help protect the knees and position you for the best interaction with the front airbags.
Side Airbags Supplemental Restraint System (SRS) — If Equipped “Supplemental Side Curtain Airbag System”, on ve- hicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag • Left and Right Side Curtain Airbags Above Side
system)
Windows
• Airbag Control Module • Interconnecting Wiring If An Airbag Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe col- lision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbag, any or all of the following may occur: • The airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passen- ger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49
are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags and seat belt pretensioners will not be in place to protect you.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
Maintaining Your Airbag System
Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an autho- rized dealer as soon as possible.
Enhanced Accident Response If the airbags and seat belt pertensioners deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 5 seconds after the vehicle has stopped moving, the interior lights will illuminate until the ignition switch is turned off.
WARNING!
• Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame. • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee blockers. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags.
Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second • The light flickers or comes on and remains on while
interval.
driving.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51
Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buck- led up in a seat appropriate for their age and size. According to crash statistics, children are safer when properly restrained in the rear seats, rather than in the front.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
The lower anchor bars of the LATCH System are located where the seat back meets the seat cushion.
In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
Lower Anchors and Tether for CHildren (LATCH) Each vehicle, is equipped with two child restraint anchor- age systems called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH child restraint anchorage systems are installed on all second- row seats.
The tether anchors are located on the rear surface of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53
Child restraint systems designed to be compatible with the vehicles LATCH System are now available. LATCH child restraints make installation into the vehicle simple and convenient. When using the LATCH System, always follow the child restraint manufactures installation instructions. If your child restraint seat is not LATCH com- NOTE: patible, install the restraint using the vehicle seat belts.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Tether Anchors There are tether strap anchorages behind all second row seating positions and the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat. When using the tether anchorages in the second row seating position, ensure that the strap is routed over the top of the seatback and under the head restraint between the head restraint posts.
When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback.
experts
Infants and Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: • Safety children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 9 kg (20 lbs). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system. Refer to “Lower Anchors and Tether for CHil- dren (LATCH)” in this section.
recommend that
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55
• The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 9 kg (20 lbs). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 9 kg (20 lbs) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 9 to 18 kg (20 to 40 lbs) and who are older than one year.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
• The belt-positioning booster seat is for children weigh- ing more than 18 kg (40 lbs), but who are still too small to fit the vehicle’s seat belts properly. If the child can not sit with knees bent over the vehicles seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/ shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.)
NOTE: www.seatcheck.org.
For
additional
information
refer
to
WARNING!
• Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat. A rearward facing child re- straint in the front seat may be struck by a deploying passenger airbag which may cause se- vere or fatal injury to the infant.
Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure
that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. The passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57
restraint manufacturer’s directions.
• Buckle the child into the seat according to the child • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury.
Installing A Child Restraint We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also
have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system.
WARNING!
Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug • Check belt fit periodically. A child’s squirming or • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
slouching can move the belt out of position.
as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59
Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.
SAFETY TIPS
Exhaust Gas
WARNING!
Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.
WARNING!
If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
Safety Checks You Should Make Inside The Vehicle
Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61
Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield.62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Periodic Safety Checks You Should Make Outside The Vehicle
Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil or other fluid leaks. Also, if gasoline fumes are detected or fuel, power steering fluid or brake fluid leaks are suspected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .67
▫ Automatic Dimming Mirror — If Equipped . . . .67
▫ Driver’s Side Outside Mirror Auto Dimmer — IfEquipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
▫ Exterior Mirrors Folding Feature . . . . . . . . . . .68
▫ Outside Mirror — Driver’s Side . . . . . . . . . . . .68
▫ Outside Mirror — Passenger’s Side . . . . . . . . . .68
▫ Power Remote-Control Mirrors . . . . . . . . . . . . .69▫ Heated Remote Control Mirrors . . . . . . . . . . . .70
▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .70䡵 Hands–Free Communication (UConnect™) — If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .78
▫ UConnect™ System Features . . . . . . . . . . . . . .81
▫ Advanced Phone Connectivity . . . . . . . . . . . . .85
▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8764 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
▫ 10–Way Driver’s Power Seat — If Equipped . . .93
▫ 8–Way Driver’s Power Seat — If Equipped . . . .93
▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . .93
▫ Adjustable Head Restraints . . . . . . . . . . . . . . .94
▫ Heated Seats — If Equipped . . . . . . . . . . . . . .94
▫ Second Row Manual Seat Recliner . . . . . . . . . .96
▫ Second Row Manual Seat Adjuster . . . . . . . . . .97
▫ Second Row Fold & Tumble Seats . . . . . . . . . . .98
▫ Third Row Easy Exit . . . . . . . . . . . . . . . . . . . .99
▫ Third Row Seating Flexibility . . . . . . . . . . . . . 101
▫ Load Floor . . . . . . . . . . . . . . . . . . . . . . . . . . 102
▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . 103䡵 Driver Memory System — If Equipped . . . . . . . 104
䡵 To Open And Close The Hood . . . . . . . . . . . . . 107
䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
▫ Overhead Console Map/Reading Lights . . . . . 108
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 109
▫ Multi-Function Lever . . . . . . . . . . . . . . . . . . . 109
▫ Headlights, Parking Lights, Instrument PanelLights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
▫ Automatic Headlights . . . . . . . . . . . . . . . . . . 111
▫ Daytime Running Lights (Canada Only) . . . . . 111
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 111
▫ Headlight Time Delay . . . . . . . . . . . . . . . . . . 111
▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 112▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 112
▫ Highbeam/Lowbeam Select Switch . . . . . . . . . 113
▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 113
䡵 Windshield Wipers And Washers . . . . . . . . . . . 113
▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 113
▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . . 114
▫ Windshield Wiper Operation . . . . . . . . . . . . . 114
▫ Intermittent Wiper System . . . . . . . . . . . . . . . 114
▫ Rear Window Wiper/Washer . . . . . . . . . . . . . 114
䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 116
䡵 Traction Control Switch — If Equipped . . . . . . . 116
䡵 Adjustable Pedals — If Equipped . . . . . . . . . . . 118
䡵 Electronic Speed Control . . . . . . . . . . . . . . . . . . 119UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 119
▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 120
▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 120
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 120
▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 120
▫ To Accelerate For Passing . . . . . . . . . . . . . . . 121
䡵 Overhead Console — If Equipped . . . . . . . . . . . 122
▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 122
▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . . 122
䡵 Garage Door Opener — If Equipped . . . . . . . . . 123
▫ Programming Homelink . . . . . . . . . . . . . . . . 124
▫ Canadian Programming/Gate Programming . . 126
▫ Using Homelink . . . . . . . . . . . . . . . . . . . . . . 12766 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 127
▫ Reprogramming a Single Homelink Button . . . 128
▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . . 129
▫ Express Open Feature . . . . . . . . . . . . . . . . . . 129
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 131
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 131
䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 131
▫ Electrical Outlet Use With Engine Off . . . . . . . 132
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 133▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . . 133
▫ Second Row Seat Cupholders . . . . . . . . . . . . . 133
▫ Third Row Seat Cupholders . . . . . . . . . . . . . . 133
䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
▫ Console Features . . . . . . . . . . . . . . . . . . . . . . 133
▫ Rear Cargo Storage Bin . . . . . . . . . . . . . . . . . 134
▫ Retractable Cargo Area Cover — If Equipped . 134
▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . . . 135
䡵 Roof Luggage Rack — If Equipped . . . . . . . . . . 137
䡵 Load Leveling System . . . . . . . . . . . . . . . . . . . 138MIRRORS
Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67
(toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Automatic Dimming Mirror — If Equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the mirror will illuminate to indicate when this feature is on.
Annoying headlight glare can be reduced by moving the small control under the mirror to the night position
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CAUTION!
To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn this feature on or off by pressing the button at the base of the Rearview Mirror.
Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
WARNING!
Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.
Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69
Press the rocker switch to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. Select a mirror and press one of the four arrows for the direction you want the mirror to move.
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Memory Seat” in section 3 of this manual. Heated Remote Control Mirrors These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear Window Defrost. Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights.
Sun Visor Extension This feature has a pull out extension on the sun visor for increased coverage.
HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., ⬙Call ѧ Mike ѧWork⬙ or ⬙Dial ѧ 248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UCon- nect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth ⬙Hands-Free Profile,⬙ version 0.96 or higher. For UConnect Customer Support call 1-877-855-8400 or visit (www.chrysler.com/ uconnect).
the UConnect website
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71
UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32
names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free profile cellular phone. UConnect™ features Bluetooth™ technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or brief- case), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system. The UCon- nect™ system allows up to seven cellular phones to be linked to system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped).72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙Operation⬙ section.
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. If your
cellular phone supports a different profile (eg., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details. The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most
UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each of the feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can either use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73
commands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please re- member, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you.
Help Command If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the ’Phone’ button and follow audible prompts for directions. All UConnect™ system sessions begin with a press of the ’Phone’ button on the mirror. Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu.
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone (re- fer to ⬙Introduction⬙ section to learn about the phone type). To complete the pairing process, you will need to reference your cellular phone owner’s manual. One of the following vehicle specific websites may also provide detailed instructions for pairing with the brand of phone that you have: NOTE: www.chrysler.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • When prompted, after the voice on beep, say ⬙Pair a
⬙Setup Phone Pairing.⬙
Phone.⬙
• You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Before attempting to pair phone, please see your cellular phone’s user manual (Bluetooth section) for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time,
only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙ section).Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • System will prompt you to say the number you want
⬙Dial.⬙
call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75
• For example, you can say ⬙234-567-8901.⬙ The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios.
Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • System will prompt you to say the name of the person
⬙Call.⬙
you want call.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previ- ously stored name entry in the UConnect™ phone- book. Refer to section ⬙Add Names to Your UCon- nect™ Phonebook,⬙ to learn how to store a name in the phonebook. • The UConnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios.
Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say
⬙Phonebook New Entry.⬙
• When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the
phonebook entry that you are adding.
After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect™ system will allow you to enter up to 32
names in the phonebook with each name having up to four associated phone numbers and designations.Edit Entries in the UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • You will then be asked for the name of the phonebook • Next, choose the number designation (home, work, • When prompted, recite the new phone number for the
mobile, or pager) that you wish to edit.
entry that you wish to edit.
⬙Phonebook Edit.⬙
phonebook entry that you are editing.
After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77
⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the ⬙Phonebook Edit⬙ feature. Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete.⬙
⬙Phonebook Delete.⬙
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager. Say the designation you wish to delete.
Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • The UConnect™ system will ask you to verify that you • After confirmation, the phonebook entries will be
wish to delete all the entries from the phonebook.
⬙Phonebook Erase All.⬙
deleted.
List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
phonebook entries.
⬙Phonebook List Names.⬙
• After the ⬙Ready⬙ prompt and the following beep, say • The UConnect™ system will play the names of all the • To call one of the names in the list, press the ⬙Voice Recognition’ button during the playing of the desired name and say ⬙Call⬙. NOTE: the user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be
interrupt
accessed through the UConnect™ system. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only either answer an incoming call or ignore it. Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to section ⬙Toggling Between Two Calls.⬙ To combine two calls, refer to section ⬙Conference Call.⬙ Place / Retrieve a Call from Hold To put a call on hold, press the ’Phone’ button until you hear a single beep which will indicate that the call has been placed on hold. To bring the call back from hold, press and hold the ’Phone’ button for 1 to 3 seconds.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
