2009 Chrysler 300 Owners Manual

Download PDF Manual
the instrument cluster on vehicles equipped with the EVIC. 4. Press and release the LOCK button on the RKE transmitter within 10 seconds. NOTE: Your RKE transmitters can be unlinked to your memory settings by pressing the SET (S) button followed by the UNLOCK button on the RKE transmitter in Step 4 above. Memory Position Recall NOTE: • The vehicle must be in PARK to recall memory posi- tions. If a recall is attempted when the vehicle is not in PARK, a message will display in the EVIC (if equipped). • The driver’s seat belt must be unbuckled to recall memory positions. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Easy Entry/Exit Seat (Available with Memory Seat Only) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons (S, 1, or 2) on the driver’s door during a recall. When a recall is cancelled, the driver seat, side mirror, adjustable pedals (if equipped), and power tilt and telescopic steering column (if equipped) stop mov- ing. A delay of one second will occur before another recall can be selected. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rearward if the driver seat position is greater than or equal to 2.7 in (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • When you remove the key from the ignition switch, the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 in and 2.7 in (22.7 mm and 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry. Each stored memory setting will have an associated Easy Entry and Easy Exit position. NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the EVIC. Refer to “Automatically Move Seat Back on Exit,” (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. “Personal Settings under TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Hood Release Lever Hood Safety Catch Use the hood prop rod (if equipped) to secure the hood in the open position. 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instru- ment panel lights, instrument panel light dimming, inte- rior lights and fog lights. 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the automatic system off, move the headlight switch out of the AUTO (A) position. NOTE: The engine must be running before the head- lights will come on in the automatic mode. Headlights On with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Turn it to the second detent for headlight, parking light and instrument panel light operation. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE under Settings “Personal The Headlights On with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to ”Headlights On with Wipers,” (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. SmartBeams — If Equipped The SmartBeam system provides increased forward light- ing at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. To Activate 1. Select “Automatic High Beams — ON” through the EVIC. Refer to “Automatic High Beams,” under “Per- sonal Settings (Customer-Programmable Features)” un- der “Electronic Vehicle Information Center (EVIC)” in Section 4. 2. Rotate the headlight switch counterclockwise to the AUTO (A) position. 3. Push the multifunction lever away from you to switch the headlights to the high beam position. Refer to “Mul- tifunction Lever” in this section. NOTE: This system will not activate until the vehicle is at or above 25 mph (40 km/h). To Deactivate Perform either of the following steps to deactivate the SmartBeam system. 1. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam position. 2. Rotate the headlight switch clockwise from the AUTO (A) to the ON position. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions on the windshield or camera lens will cause the system to function improperly. Headlight Time Delay This feature provides the safety of headlight illumination for up to 90 seconds (programmable) when leaving your vehicle in an unlit area. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 To activate the delay feature, turn OFF the ignition switch while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay interval begins when the headlight switch is turned off. If you turn the headlights, park lights, or ignition switch ON again, the system will cancel the delay. If you turn the headlights off before the ignition, they will turn off in the normal manner. NOTE: The lights must be turned off within 45 seconds of turning the ignition OFF to activate this feature. The headlight delay time is programmable on vehicles equipped with the EVIC. Refer to “Delay Turning Head- lights Off,” under (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. “Personal Settings 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is ON, the headlights are off and the parking brake is off. The headlight switch must be used for normal nighttime driving. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened. Fog Lights — If Equipped The front fog light switch is built into the head- light switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn off the headlight switch. An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. However, selecting the high beam headlights will turn off the fog lights. Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights. The multifunction lever is located on the left side of the steering column. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Moving the multifunction lever up or down also causes the corresponding turn signal indicator in the outside mirror (if so equipped) to flash. For details, refer to “Outside Mirrors with Turn Signal & Approach Light- ing” under “Mirrors” in this Section. You can also signal a lane change by moving the multi- function lever partially up or down without moving beyond the detent. Releasing the lever at the detent will provide three flashes. If either indicator has a very fast flash rate, check for an inoperative outside light bulb. If an indicator fails to light when the multifunction lever is moved, see your autho- rized dealer for service. NOTE: A “Turn Signal On” message will appear in the EVIC (if equipped) and a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. Multifunction Lever Turn Signals Move the multifunction lever up or down and the corresponding turn signal indicator in the instrument cluster flashes to show proper operation of the front and rear turn signal lights. 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the multifunction lever is released. Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned on by pressing the lens. Press the lens a second time to turn the light off. These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. Overhead Console Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the in- strument panel so equipped, the lighting in the door map pockets and cupholders. lights and, if UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Interior Light Defeat (OFF) Rotate the dimmer control to the extreme bottom OFF position. The interior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens all text displays such as the odometer, EVIC (if equipped), and radio when the park- ing lights or headlights are on. WINDSHIELD WIPERS AND WASHERS The multifunction lever operates the windshield wipers and washer when the ignition switch is in the ON 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The multifunction lever is located on the left side of the steering column. Windshield Wiper/Washer Control Rotate the end of the multifunction lever to the first detent, past the intermittent settings for low speed wiper operation, or to the second detent past the intermittent settings for high speed wiper operation. CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the wind- shield wipers may result if the wiper switch is left in any position other than off. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause be- tween cycles desirable. Rotate the end of the multifunc- tion lever to the first detent position, and then turn the end of the multifunction lever to select the desired delay interval. There are six delay settings which allow you to regulate the wipe interval from a minimum of one cycle every second to a maximum of approximately 23 seconds between cycles. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist Feature Lightly push the multifunction lever inward (toward the steering column) to activate a single wipe cycle to clear off road mist or spray from a passing vehicle. The wipers will continue to operate until you release the multifunc- tion lever. Windshield Washers To use the washer, push the multifunction lever inward completely (toward the steering column) and hold it for as long as washer spray is desired. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the windshield wiper is turned off, the wipers will operate for three wipe cycles and then turn off. Headlights On with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The Headlights On with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to ”Headlights On with 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE under Settings “Personal Wipers,” (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or over spray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the six intermittent wiper settings to activate this feature. The sensitivity of the system is adjustable from the multifunction lever. Wiper delay position 1 is the least sensitive and wiper delay position 6 is the most sensitive. Choose setting 3 or 4 for normal rain conditions. Choose setting 2 or 1 if you desire less wiper sensitivity. Choose setting 5 or 6 if you desire more sensitivity. Place the multifunction lever in the off position when not using the system. wiper speed is in the low or high position. NOTE: • The rain sensing feature will not operate when the • The rain sensing feature may not function properly when ice or dried salt water is present on the wind- shield. • Use of Rain-X威 or products containing wax or silicone • The rain sense feature can be turned on and off through the EVIC (if equipped). Refer to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. may reduce rain sensor performance. The rain sensing system has protective features for the wiper blades and arms. It will not operate under the following conditions: • Low Temperature Wipe Inhibit — The rain sensing feature will not operate when the ignition is first switched ON, and the vehicle is stationary, and the outside temperature is below 32°F (0°C), unless the wiper control on the multifunction lever is moved, or the vehicle speed becomes greater than 0 mph (0 km/h), or the outside temperature rises above freezing. • Neutral Wipe Inhibit — The rain sensing feature will not operate when the ignition is ON, and the trans- mission shift lever is in the NEUTRAL position, and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control on the multifunction lever is moved or the shift lever is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column lever is located below the multifunction lever on the steering column. Power Tilt/Telescoping Steering To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired. NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “Driver Memory Seat” in this section. WARNING! Moving the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows both the brake and accelerator pedal to move toward or away from the driver to provide improved position with the steering UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 wheel. The switch is located on the front side of the driver’s seat cushion side shield. Adjustable Pedals Switch Press the switch forward to move the pedals forward (toward the front of the vehicle). Press the switch rearward to move the pedals rearward (toward the driver). 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is on. One of the following messages will display in the Electronic Vehicle Information Center (if equipped) if a pedal adjustment is attempted when the system is locked out: “Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Dis- abled — Vehicle In Reverse.” (EVIC) NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the adjustable pedals to pre- programmed positions. Refer to “Driver Memory Seat” in this section. CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever located on the right side of the steering wheel operates the system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it. 1 — CANCEL 2 — RESUME ACCEL 3 — ON/OFF 4 — SET DECEL 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle reaches the speed desired, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed. NOTE: • Electronic Speed Control will only function in 3rd, 4th, or 5th gear when in the Autostick威 mode (if equipped). • The Electronic Speed Control may not engage if a different size tire is installed on one wheel, such as the compact spare tire. To Deactivate The system will disable Electronic Speed Control without erasing the memory if you: • Softly tap the brake pedal, • Depress the brake pedal, or • Pull the Electronic Speed Control lever toward you to CANCEL. Pushing and releasing the ON/OFF button or turning off the ignition erases the set speed from memory. To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever upward to RESUME ACCEL and release. Then remove your foot from the accelerator pedal. To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the Electronic Speed Control lever in RESUME ACCEL. When the Electronic Speed Control lever is released, a new set speed will be established. Tapping the Electronic Speed Control lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the Electronic Speed Control lever is tapped speed increases, so tapping the Electronic Speed Control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while Electronic Speed Control is set, push down and hold the Electronic Speed Control lever in SET DECEL. Release the Electronic Speed Control lever when the desired speed is reached, and a new set speed will be established. Tapping the Electronic Speed Control lever to SET DE- CEL once will result in a 1 mph (1.6 km/h) speed decrease. Each time the Electronic Speed Control lever is tapped, speed decreases. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control on Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. The automatic transmission will downshift while climb- ing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills, a greater speed loss or gain may occur, so it may be preferable to drive without Electronic Speed Control. 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling on highways and major roadways. However, it is not a safety system and not designed to prevent collisions. ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes an infrared sensor designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, • If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or acceleration automatically to maintain a preset following distance, while matching the speed of the vehicle ahead. ACC will maintain a fixed set speed. WARNING! • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibil- ity to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions. Your complete attention is always re- quired while driving to maintain safe control of your vehicle. Failure to follow these warnings can result in an accident or serious personal injury.The ACC system: • Does not react to pedestrians, oncoming vehicles, and stationary objects (i.e., a stopped vehicle in a traffic jam or a disabled vehicle). (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not predict the lane curvature or the move- ment of preceding vehicles and will not compen- sate for such changes. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings. • May not detect a vehicle ahead when strong light (for example, sunrise or sunset) is directly shining on the front of the vehicle. • Can only apply a maximum of 25% of the vehicle’s braking capability, and will not bring the vehicle to a complete stop. 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! You should switch off the ACC system: • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones). • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes; and when towing a trailer. • When circumstances do not allow safe driving at a constant speed. Failure to follow these warnings can result in an accident or serious personal injury. appropriate distance between vehicles. The Cruise Control system has two control modes. • Adaptive cruise control mode for maintaining an • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. Note: The system will not react to preceding vehicles. Always be aware of the mode selected. You can change the mode by using the control lever. The two control modes function differently. Always confirm which mode is selected. Adaptive Cruise Control (ACC) Operation The speed control lever (located on the right side of the steering wheel) operates the ACC system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 When the system is turned on and in the READY state, the Electronic Vehicle Information Center (EVIC) dis- plays “ACC READY.” When the system is OFF, the EVIC displays “CRUISE OFF.” NOTE: You cannot enable ACC under the following conditions: • When you apply the brakes. • When the parking brake is set. • When the automatic transmission is in PARK, RE- • When the Electronic Stability Program (ESP) is • When pushing the RESUME/ACCEL switch without a VERSE, or NEUTRAL. switched off. previously set speed in memory. 1 — DISTANCE SETTING 2 — CANCEL 3 — RESUME/ACCEL 4 — ON/OFF/MODE 5 — SET/DECEL Activating Adaptive Cruise Control (ACC) You can only activate ACC if the vehicle speed is above 25 mph (40 km/h). 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF/MODE button located on the end of the speed control lever. The ACC menu in the EVIC displays “ACC READY.” WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could acciden- tally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To Set a Desired Acc Speed When the vehicle reaches the speed desired, push the lever downward (SET/DECEL) and release. The EVIC will display the set speed. To turn the system OFF, push and release the ON/OFF/ MODE button again. At this time, the system will turn off and the EVIC will display “CRUISE OFF.” UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • The system will not be controlling the distance be- tween your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • The message “DRIVER OVERRIDE” will display in the EVIC. To Cancel The system will disable ACC without erasing the memory if: 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You softly tap the brake pedal. • You depress the brake pedal. • You pull the speed control lever toward you to CAN- • The Electronic Stability Program/Traction Control CEL. System (ESP/TCS) activates. To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the ON/OFF/MODE button. • You turn OFF the ignition. • You switch off ESP. To Resume Speed Push the lever upward (RESUME/ACCEL) and release. Then remove your foot from the accelerator pedal. The EVIC will display the last set speed. WARNING! The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. This could cause an accident and/or serious injury. To Vary the Speed Setting While ACC is set, you can increase the set speed by lifting and holding the lever up (RESUME/ACCEL). If the lever is continually held, the set speed will continue to increase in 5 mph (10 km/h) increments until the lever is released. The increase in set speed is reflected in the EVIC display. Tapping the lever up once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of the lever results in an increase of 1 mph (1 km/h). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 While ACC is set, the set speed can be decreased by pushing and holding the lever down (SET/DECEL). If the lever is continually held, the set speed will continue to decrease in 5 mph (10 km/h) increments until the lever is released. The decrease in set speed is reflected in the EVIC display. Tapping the lever down once will result in a 1 mph (1 km/h) decrease in set speed. Each subsequent tap of the lever results in a decrease of 1 mph (1 km/h). NOTE: • When you use the lever to decelerate, if the engine’s braking power does not slow the vehicle sufficiently to reach the set speed, the brake system will automati- cally slow the vehicle. 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending down- hill. This is normal operation and necessary to main- tain set speed. Setting the Following Distance in ACC The specified following distance for ACC can be set by varying the distance setting between long, medium, and short. Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead. This distance setting displays in the EVIC. 1 — Sensor Bars. Default Distance Setting is Three Bars = Long. To change the distance setting, push the lever away from you (DISTANCE) and release. Each time this is done, the distance setting adjusts between long, medium, and short. If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the EVIC displays the “Sensed Vehicle Indi- cator” icon, and the system adjusts vehicle speed auto- matically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set • The vehicle ahead moves out of your lane or view of • The vehicle ahead slows to a speed below 15 mph (24 km/h) and the system automatically disengages itself. the sensor. speed. • The distance setting is changed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • The system disengages. (Refer to the information on ACC Activation). The maximum braking applied by ACC is limited; how- ever, the driver can always apply the brakes manually, if necessary. NOTE: The brake lights will illuminate whenever the ACC system applies the brakes. A Proximity Warning will alert the driver if ACC predicts that to maintain the set distance. If this occurs, a visual alert “ATTENTION” will flash in the EVIC and a chime will sound while ACC continues to apply its maximum braking capacity. When this occurs, you should immedi- ately apply the brakes as needed to maintain a safe distance from the vehicle ahead. its maximum braking level is not sufficient 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cluster between the speedometer and the tachometer. The information it displays depends on ACC system status. Press the MENU button (located on the steer- ing wheel) repeatedly until one of the follow- ing displays in the EVIC: Menu Button Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings. The EVIC is located in the upper part of the instrument CRUISE OFF − When ACC is deactivated, “CRUISE OFF.” the display will read UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 ACC READY − When ACC is activated, the display will read “ACC READY.” 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC SET − When ACC is set, the set speed will display. The set speed will continue to display in place of the odometer reading when changing the EVIC display while ACC is set. 1 — Sensed Vehicle Indicator 2 — Set Speed 3 — Your Vehicle 4 — Following Distance Setting: Three Bars = Long; Two Bars = Medium; One Bar = Short. The ACC SET screen will display once again if any ACC activity occurs, which may include any of the following: • Set speed change • Distance setting change • System cancel • Acquisition/loss of Target UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • Driver override • System off • Proximity warning • ACC warning The EVIC will return to the last display selected after five seconds of no ACC activity. 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Display Warnings and Maintenance ACC Blinded Warning The ACC Blinded Warning will display when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such as in snow, fog, heavy rain, or when driving into direct sunlight (sunrise or sunset). The ACC system may also become tempo- rarily blinded due to obstructions, such as dirt or ice. In these cases, the EVIC will display “ACC Blinded” and the system will deactivate. If the ACC Blinded Warning is active Normal NOTE: (Fixed Speed) Cruise Control is still available. For addi- tional information refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located behind the grille, slightly offset from the center of the grille. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • Always keep the sensor clean. Carefully wipe the sensor lens with a soft cloth. Be cautious not to damage the sensor lens. • Do not remove any screws from the sensor or the sensor mount. Doing so could cause an ACC system malfunction or failure and require a sensor realign- ment. • If the sensor is damaged due to an accident, see your • Do not attach or install any accessories near the sensor, including transparent material or aftermarket grilles. Doing so could cause an ACC system failure or malfunction. authorized dealer for service. ACC Sensor Location To keep the ACC System operating properly, it is impor- tant to note the following maintenance items: When the condition that deactivated the system is no longer present, the system will return to the “CRUISE OFF” state and will resume function by simply reactivat- ing it. 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Installing a vehicle front-end protector or an NOTE: aftermarket grille or modifying the grille is not recom- mended. Doing so may block the sensor and inhibit ACC operation. ACC Unavailable Warning If the system turns off, and the EVIC displays ⬙ACC UNAVAILABLE,⬙ there may be a temporary malfunction that limits ACC functionality. Although the vehicle is still drivable under normal conditions, ACC will be tempo- rarily unavailable. If this occurs, try activating ACC again later, following a key cycle. If the problem persists, see your authorized dealer. Service ACC Warning If the system turns off, and the EVIC displays “SERVICE ACC,” it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer. Precautions While Driving with ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpect- edly. The driver needs to stay alert and may need to intervene. Adding a Trailer Hitch The weight of a trailer hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a hitch, such as reduced detection range, please see your authorized dealer for service. Offset Driving ACC may not detect a vehicle in the same lane that is offset from your direct line of travel. There will not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Turns and Bends In turns or bends, ACC may detect a vehicle ahead too late or too early. This may cause your vehicle to brake late or unexpectedly. Give extra attention in curves and be ready to apply the brakes if necessary. Be sure to select an appropriate speed while driving in curves. 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC on Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC perfor- mance may be limited. ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other station- ary objects in a curve. This may also occur at the base of dramatic hills. This is normal operation and your vehicle does not require service. Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it will not until it may be too late to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient distance to the lane-changing vehicle. Always be attentive and ready to apply the brakes if necessary. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There will not be suffi- cient distance to the vehicle ahead. 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects and Vehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary. General Information CLASS 1 LASER PRODUCT Classification Specifications: 21 C.F.R part 1040.10 & 1040.11 DIN EN 60825-1:2003 IEC 60825-1:2001 Normal (Fixed Speed) Cruise Control Mode In addition to adaptive cruise control mode, a normal (fixed speed) cruise control mode is available for cruising at fixed speeds. The Normal cruise control mode is designed to maintain a set cruising speed without requir- ing the driver to operate the accelerator. Cruise control can only be operated if the vehicle speed is above 25 mph (40 km/h). To change modes, press and hold the ⬙ON/OFF/MODE⬙ button for at least one second in either the OFF state or the READY state. ⬙Normal Cruise Ready⬙ will be dis- played once the mode becomes available. To switch back to ACC, press and hold the “ON/OFF/MODE” button again for at least one second. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! In the normal cruise control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since the presence of the vehicle ahead nor the vehicle-to- vehicle distance is detected. Be sure to maintain a safe distance between your vehicle and the vehicle ahead. Always be aware which mode is selected. To set a Desired Speed When the vehicle reaches the speed desired, tap the lever down and release (“SET/DECEL”). The EVIC will dis- play the set speed. NOTE: You must observe the display when setting or changing speed, not the speedometer. 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting There are two ways to change the set speed: • Use the accelerator pedal to adjust the vehicle to the desired speed and push the lever down (“SET/ DECEL”). • Tap the stalk up (“ACCEL”) or down (“DECEL”) to increase or decrease the set speed in 1 mph (1 km/h) increments respectively. Hold for 5 mph (10 km/h) increments. To Cancel The system will disable Normal cruise control without erasing the memory if: • You softly tap or depress the brake pedal. • You pull the speed control lever toward you (“CAN- CEL”). • The Electronic Stability Program/Traction Control System (ESP/TCS) activates. To Resume Push the lever up and release (“RESUME/ACCEL”) and then remove your foot from the accelerator pedal. The EVIC will display the last set speed. To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the “ON/OFF/MODE” button. • You turn off the ignition. • You switch off ESP. If the cruise control system is turned off and reactivated, the system will return to the Vehicle-to-vehicle (adaptive) distance control mode. REAR PARK ASSIST The Rear Park Assist is a driver aid that senses for obstacles behind the vehicle. Refer to the Warnings, Cautions, and Notes in this section for system limitations and usage recommendations. The Rear Park Assist is active when the driver shifts the transmission into the REVERSE position, and the parking brake is not applied, and the vehicle speed is less than 10 mph (16 km/h). The system can be turned on or off through the Electronic Vehicle Information Center (EVIC) when the vehicle is in PARK. Refer (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. “Personal Settings to UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 The system uses four sensors located in the rear bumper to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia. The warning display located above the rear window provides both visible and audible warnings to indicate the range of the object. Rear Park Assist LED Display 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The warning display contains two sets of yellow and red indicators, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the indicators either through the rearview mirror or by looking at the display above the rear window. WARNING DISPLAY DISTANCES The system dimly illuminates the two inner most yellow indicators when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: DISPLAY INDICA- TOR Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED OBSTACLE DISTANCE FROM: REAR CORNERS 31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm) REAR CENTER 79 in (200 cm) 51.2 in (130 cm) 45.3 in (115 cm) 39.3 in (100 cm) 33.5 in (85 cm) 27.6 in (70 cm) 19.7 in (50 cm) 11.8 in (30 cm) INDICATOR COLOR Yellow Yellow Yellow Yellow Yellow Yellow Red Red AUDIBLE SIGNAL Yes, Half Second No No No No No Yes, Intermittent Yes, Continuous NOTE: The Rear Park Assist will MUTE the radio, if on, when the system is sounding an audio tone. WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots be- fore backing up. You are responsible for safety and must continue to pay attention to your surround- ings. Failure to do so can result in serious injury or death. (Continued) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 WARNING! (Continued) • Before using the Rear Park Assist, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red indicators ON. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • The Rear Park Assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be tempo- rarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist to be able to stop in time when the obstacle is detected. It is recommended that the driver look over their shoulder when using the Rear Park Assist. NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System” appears in the EVIC after making sure the rear bumper is clean please see your authorized dealer. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, and an optional power sunroof switch. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a ⬙push/push⬙ design. Push on the raised bar on the compartment door to open. Push on the raised bar to close. GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. Courtesy/Reading Lights Overhead Console At the forward end of the console are two courtesy/ reading lights. Press the lens to turn on the light. Press it a second time to turn off the light. 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines desig- nating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or as- sistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.” Release the buttons when the EVIC mes- sage states “CHANNELS CLEARED.” It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威. 3. Simultaneously, press and hold both the chosen HomeLink威 button and the hand-held transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” Then release both the HomeLink威 and hand-held trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter. It may take up to 30 seconds, or longer, in rare cases. The garage door may open and close while you train. 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.” If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLink威 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE has successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAIN- ING” to “CHANNEL # TRAINED.” If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) The hand-held transmitter of the device may also be used at any time. Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.” Note that all channels will be erased. Indi- vidual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 2. This device must accept any interference that may be received including interference that may cause undesired operation NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met. Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the learn button on the garage door opener to • Did you unplug the device for training, and remember complete the training for rolling code. to plug it back in? If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Controls WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are also properly secured. • Do not allow small children to operate the sun- roof. Never allow fingers or other body parts, or any object, to project through the sunroof opening. Injury may result. Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully and then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the sunroof switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move toward the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙V⬙ button in the center of the switch, and the sunroof will open to the vent position. This is called “Express Vent”, which operates regardless of sunroof position. During Express Vent operation, any movement of the sunroof switch will stop the sunroof. 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, then adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 10 minutes after the ignition switch is turned OFF. Opening either front door will cancel this feature. For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to 60 minutes after the ignition switch is turned OFF. Opening either front door will cancel this feature. The time is programmable. Refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS There are two 12-Volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The 12-Volt power outlet next to the ash receiver tray (if equipped with an optional Smoker’s Package) has power available only when the ignition is ON. This outlet will also operate a conventional cigar lighter unit. WARNING! Do not place ashes inside the cubby bin located on the center console on vehicles not equipped with the ash receiver tray. A fire leading to bodily injury could result. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 If desired, the power outlet next to the ash NOTE: receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position. Front Power Outlet 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an the vehicle. electric shock and failure. Center Console Power Outlet UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. (Continued) 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants elbows. Front Seat Cupholders Rear Seat Cupholders STORAGE Console Features The center console contains two shift bezel cubby bins with rubber mats for holding small items. For vehicles not equipped with navigation radio, the console also contains an extra storage bin located below the climate control, which holds up to four CD jewel cases. Without Vehicle Entertainment System (VES威) Two separate storage compartments are also located underneath the armrest. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 1 — Release button for bottom compartment 2 — Release button for top compartment 3 — Top Compartment 4 — Bottom Compartment. (You can access this compartment directly, without first exposing the upper compartment, by oper- ating the Release Button for the bottom compartment with the armrest down.) 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12-Volt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the left and right side of the top compartment provides clearance for power cords to pass conveniently out of the bin with the lid closed. This feature is ideal for games, laptop’s, cellular phones or other electrical equipment. The con- sole’s front opening lid allows for easy access to these compartments. With Vehicle Entertainment System (VES威) The center console contains a large storage compartment. The storage compartment contains a 12-Volt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the top left and right side of the storage compartment provides clearance for power cords to pass conveniently out of the compartment with the lid closed. This feature is ideal for games, laptop’s, cellular phones, or other electrical equipment. The console’s front-opening lid allows for easy access to the storage compartment for both the driver and the front passenger. Cargo Area The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly-flat extension of the load floor. WARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: (Continued) WARNING! (Continued) • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or collision. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 WARNING! • Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. (Continued) 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. CARGO AREA FEATURES Trunk Mat — If Equipped A reversible trunk mat covers the bottom of the cargo area. The rubber side of the mat is used to protect the interior of the trunk from mud, snow, and debris. It provides a nonskid surface to keep cargo from sliding. REAR WINDOW FEATURES Rear Window Defroster The electric rear window defroster button is lo- cated on the climate control. Press this button to turn on the rear window defroster and the heated outside rearview mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time. CAUTION! • To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Labels can be peeled off after soaking with warm water. LOAD LEVELING SYSTEM — IF EQUIPPED The automatic load leveling system will provide a level- riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 If the leveled vehicle is not moved for approximately 15 hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system. UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 205 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 206 䡵 Instrument Cluster — Premium . . . . . . . . . . . 207 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 208 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 ▫ Oil Change Required . . . . . . . . . . . . . . . . . . 225 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 226 ▫ Automatic All Wheel Drive (AWD) Displays — If Equipped . . . . . . . . . . . . . . . . . . . . . . 228 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 229 ▫ Driver-Selectable Surround Sound (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . 231 ▫ uconnect威 gps (Navigation) — If Equipped . . 232 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . 232 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . 237 202 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 ▫ Operating Instructions - Radio Mode . . . . . . 238 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . 246 ▫ Notes On Playing MP3/WMA Files . . . . . . . 248 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 䡵 AM/FM/CD/DVD Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 253 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . 253 ▫ Operating Instructions — uconnect威 phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 253 . . . . . . . . . . . . . . . 253 ▫ Clock Setting Procedure 䡵 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . 256 ▫ Operating Instructions — Radio Mode . . . . . 256 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 259 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 261 ▫ Operation Instructions - Auxiliary Mode . . . . 264 䡵 Sales Code RES/RSC — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 ▫ Operating Instructions — Radio Mode . . . . . 265 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 270 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 273 ▫ List Button (CD Mode For MP3 Play) . . . . . . 275 ▫ Info Button (CD Mode For MP3 Play) . . . . . . 275 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 277 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 278 ▫ Controlling The iPod威 Using Radio Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 280 UNDERSTANDING YOUR INSTRUMENT PANEL 203 䡵 uconnect威 studios (Satellite Radio) — If Equipped (REN/REQ/RER/RES/REU Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 282 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 282 ▫ Selecting uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 283 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 283 ▫ Operating Instructions — uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . 284 ▫ Operating Instructions — uconnect威 phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 286 204 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Video Entertainment System (VES)™ (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 286 䡵 Kicker威 High Performance Sound System With Driver-Selectable Surround (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 287 䡵 uconnect studios威 (Sirius Backseat TV™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 288 䡵 Video Entertainment System (VES)™ — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 288 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 291 䡵 CD/DVD Maintenance . . . . . . . . . . . . . . . . . 292 䡵 Radio Operation And Cellular Phones . . . . . . . 293 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 294 ▫ Manual Air Conditioning And Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 ▫ Automatic Temperature Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . 297 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 302 INSTRUMENT PANEL FEATURES UNDERSTANDING YOUR INSTRUMENT PANEL 205 1 - Air Outlet 2 - Instrument Cluster 3 - Hazard Switch 4 - Analog Clock 5 - Electronic Stability Program Off Button* / Traction Control System Off Button* 6 - Glove Compartment 7 - Radio 8 - Climate Control 9 - Heated Seat Switch* 10 - Power Outlet 11 - Ash Tray* 12 - Storage Compartment* 13 - Ignition Switch 14 - Hood Release 15 - Trunk Release Switch 16 - Headlight Switch * If Equipped 206 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE INSTRUMENT CLUSTER — PREMIUM UNDERSTANDING YOUR INSTRUMENT PANEL 207 208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Electronic Speed Control / Adaptive Cruise Control (ACC) Indicator Light — If Equipped This light will turn on when the electronic speed control or Adaptive Cruise Control (ACC) is ON. 2. Low Fuel Indicator Light This light will turn on and a single chime will sound when the fuel level drops to 1/8 tank. 3. Front Fog Light Indicator — If Equipped This light will turn on when the front fog lights are ON. 4. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • Check for an inoperative outside light bulb if either indicator flashes at a rapid rate. 5. Speedometer Indicates vehicle speed. 6. Odometer/Trip Odometer Display / Electronic Vehicle Information Center (EVIC) Display — If Equipped The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Trip Odometer Button” for additional information. NOTE: U.S. Federal regulations require upon transfer of vehicle ownership, the seller certify the mileage the vehicle has been driven. Therefore, if the odometer reading is changed because of repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. Rear Wheel Drive (RWD) / All Wheel Drive (AWD) Displays (Base Cluster) On vehicles equipped with a Base Instrument Cluster, the odometer will display “2drivE” when the vehicle is in Rear Wheel Drive (RWD), and “4drivE” when All Wheel Drive (AWD) is activated. If the odometer displays the “tCASE” warning message after engine start up, or during driving, the AWD system is not functioning properly and service is required. NOTE: Vehicles equipped with Electronic Vehicle Infor- mation Center (EVIC) will display “ALL WHEEL DRIVE” and “REAR WHEEL DRIVE” when the appro- priate condition exists. The EVIC will display “SERVICE AWD SYSTEM” if the system is not functioning properly UNDERSTANDING YOUR INSTRUMENT PANEL 209 and service is required. Refer to “Electronic Vehicle Information Center (EVIC)” in this section for more information. Change Oil Message (Base Cluster) Your vehicle is equipped with an engine oil change indicator system. The “Change Oil” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the TRIP ODOMETER button on the instrument cluster. To 210 UNDERSTANDING YOUR INSTRUMENT PANEL reset the oil change indicator system (after performing the scheduled maintenance) perform the following pro- cedure: 1. Turn the ignition switch to the ON position. (Do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the LOCK position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. On vehicles equipped with a Premium Instrument Clus- ter, this display shows the Electronic Vehicle Information Center (EVIC) messages when the appropriate conditions exist. Lo tirE When the appropriate condition exists the odometer display will toggle between Lo and tirE for three cycles. Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the EVIC. Tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). Refer to “Electronic Vehicle Information Center (EVIC)” in this section for more information. 7. Tachometer The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Ease up on the accelerator before reaching the red area. 8. Engine Temperature Warning Light

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2009 Chrysler 300 Owners Manual