Download PDF Manual


Metric


For eAssist vehicles, this gauge assists in driving efficiently and may vary based on driver input. To maximize efficiency, keep the gauge pointed in the solid green zone in the center of the gauge. The gauge moves to the left when braking and to the right when accelerating. When either is done aggressively, the vehicle is being driven less efficiently and the gauge will move further from the center.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (13,1)


Instruments and Controls


5-13


If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.


Safety Belt Reminders


Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.


times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the chime nor the light comes on. Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System on page 3‑23.


When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several


When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if


English


This gauge shows the engine coolant temperature. If the indicator needle moves to the hot side of the gauge toward the shaded area, the engine is too hot. In eAssist vehicles, the engine coolant warning light will come on when the engine is too hot. See Engine Coolant Temperature Warning Light on page 5‑21 for more information.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (14,1)


5-14


Instruments and Controls


the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the warning light and/or chime, remove the object from the seat or buckle the safety belt.


Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑17.


The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.


{ WARNING


If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.


Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑23 for important safety information. The instrument panel has a passenger airbag status indicator.


When the vehicle is started, the passenger airbag status indicator will light ON and OFF for several seconds as a system check. If you are using remote start, if equipped, to start the vehicle from a distance, you may not see the system check. Then, after several more seconds, the status indicator


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (15,1)


Instruments and Controls


5-15


will light either ON or OFF to let you know the status of the front outboard passenger frontal airbag. If the word ON is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag is allowed to inflate. If the word OFF is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.


{ WARNING


If the airbag readiness light ever comes on and stays on, it means that something may be wrong


(Continued)


WARNING (Continued)


with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑14 for more information, including important safety information.


Charging System Light


The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer.


If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.


Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in ON/RUN for key access or Service Only Mode for keyless access, as a check to show it is working. If it does not, have the vehicle serviced


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (16,1)


5-16


Instruments and Controls


by your dealer. See Ignition Positions (Keyless Access) on page 9‑17 or Ignition Positions (Key Access) on page 9‑15 for more information.


If the malfunction indicator lamp comes on while the engine is running, this indicates that the OBD II system has detected a problem and diagnosis and service might be required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system also assists the dealer technician in correctly diagnosing any malfunction.


Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10‑3.


This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (17,1)


Instruments and Controls


5-17


The following may correct an emission control system malfunction: . Check that the fuel cap is fully


installed. See Filling the Tank on page 9‑49. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.


. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up.


If one or more of these conditions occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑46. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).


The DLC is under the instrument panel to the next to the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:


The malfunction indicator lamp is on while the vehicle is running. The vehicle is in ON/RUN for key access, or Service Only Mode for keyless access and the malfunction indicator lamp does not come on. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (18,1)


5-18


Instruments and Controls


vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.


Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working.


If the warning light comes on, there is a brake problem. Have the brake system inspected right away.


Metric


English


The brake system warning light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.


{ WARNING


The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off


(Continued)


WARNING (Continued)


the road and carefully stopped, have the vehicle towed for service.


If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10‑89.


Electric Parking Brake Light


Metric


English


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (19,1)


Instruments and Controls


5-19


The parking brake status light comes on when the brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the electric parking brake system. A message may also display on the Driver Information Center (DIC). See Brake System Messages on page 5‑29 for more information. If the light does not come on, or remains flashing, see your dealer.


Service Electric Parking Brake Light


not come on, have it fixed so it will be ready to warn if there is a problem. If this light stays on, there is a problem with a system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See Parking Brake on page 9‑32 for more information.


Antilock Brake System (ABS) Warning Light


The service electric parking brake light should come on briefly when the vehicle is in ON/RUN. If it does


The Antilock Brake System (ABS) light comes on briefly when the engine is started.


If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn the ignition off. A chime may also sound when the light comes on steady. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5‑18. See Driver Information Center (DIC) on page 5‑24 for all brake related DIC messages.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (20,1)


5-20


Instruments and Controls


Up-Shift Light


For manual transmission vehicles, there is an up-shift light that comes on in the lower DIC area. It shows when to shift to the next higher gear for best fuel economy. See Manual Transmission on page 9‑30.


Traction Off Light


This light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light also comes on and the system turns off if there is a problem with the traction control system. If the light comes on and stays on for an extended period of time while the system is turned on, the vehicle needs service. See Traction Control System (TCS) on page 9‑35 and StabiliTrak® System on page 9‑36 for more information.


StabiliTrak® OFF Light


This light comes on when the StabiliTrak system is turned off. If the Traction Control System (TCS) is off, wheel spin is not limited. If StabiliTrak is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak system and the warning light turns off. See Traction Control System (TCS) on page 9‑35 and StabiliTrak® System on page 9‑36 for more information.


Traction Control System (TCS)/StabiliTrak® Light


The Traction Control System (TCS)/ StabiliTrak light comes on briefly when the engine is started.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (21,1)


If the light does not come on, have the vehicle serviced by the dealer. If the system is working normally, the indicator light turns off. If the light is on while certain DIC messages display, this indicates that the TCS and StabiliTrak systems are not working or are disabled. If the light is on and not flashing, the TCS and potentially the StabiliTrak system have been disabled. Check the DIC messages to determine which feature(s) is no longer functioning and whether it is because of the driver turning off the feature(s), or because the system is not working properly and the vehicle requires service. If the TCS is disabled, wheel spin is not limited. If the StabiliTrak system is disabled, the system does not aid in maintaining directional control of the vehicle.


Instruments and Controls


5-21


If the indicator/warning light is on and flashing, the TCS or the StabiliTrak system is actively working. See StabiliTrak® System on page 9‑36 and Traction Control System (TCS) on page 9‑35 for more information. See Ride Control System Messages on page 5‑32 for more information on the messages associated with this light.


Engine Coolant Temperature Warning Light


If it does not, have the vehicle serviced by the dealer. If the system is working normally, the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat. See Engine Overheating on page 10‑20. The vehicle's engine could be damaged, and it might not be covered by the vehicle warranty. Never drive with the engine coolant temperature warning light on. The engine coolant temperature warning light comes on when the engine has overheated. If this happens, pull over and turn off the engine as soon as possible. See Engine Overheating on page 10‑20.


For eAssist vehicles, this light comes on briefly while starting the vehicle.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (22,1)


5-22


Instruments and Controls


Tire Pressure Light


For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.


When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5‑33. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑48.


When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑51.


low can also damage the


Engine Oil Pressure Light Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.


The oil pressure light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (23,1)


Low Fuel Warning Light


Security Light


High-Beam On Light


Instruments and Controls


5-23


This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light comes on and a chime sounds periodically when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank.


The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) on page 2‑14 or Immobilizer Operation (Keyless Access) on page 2‑14.


The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑2 for more information.


Front Fog Lamp Light


For vehicles with fog lamps, this light comes on when the fog lamps are on.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (24,1)


5-24


Instruments and Controls


The light goes out when the fog lamps are turned off. See Fog Lamps on page 6‑4 for more information.


Lamps On Reminder


For vehicles with cruise control, the cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light turns off when the cruise control is turned off. See Cruise Control on page 9‑41.


Door Ajar Light


For vehicles with the lamps on reminder light, it comes on when the lights are in use.


Cruise Control Light


When the ignition is on, this light stays on until all doors are closed and completely latched. If a door is not closed properly, a chime sounds after the engine is started and the vehicle is not in P (Park).


Information Displays


Driver Information Center (DIC) The Driver Information Center (DIC) displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5‑28. All messages appear in the DIC display in the center of the instrument cluster. On some models, the DIC may have some warning lights or indicators in the top portion of the display. See Warning Lights, Gauges, and Indicators on page 5‑8. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5‑34. DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever,


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (25,1)


on the left side of the steering wheel. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The bottom of the DIC display shows the position of the shift lever and the odometer. It may also show the direction the vehicle is driving. In cold weather the DIC display may change slowly. This is normal and will move more quickly as the vehicle's interior temperature rises.


DIC Buttons


1. SET/CLR (Set/Clear): Press to set, or press and hold to clear, the menu item displayed.


Instruments and Controls


5-25


2. w / x (Thumbwheel): Use to


scroll through the items in each menu.


3. MENU: Press to display the Trip/


Fuel Menu and the Vehicle Information Menu. On some vehicles, there is also an ECO Menu. This button is also used to return to or exit the last screen displayed on the DIC. Trip/Fuel Menu (TRIP) Items Press MENU on the turn signal lever until TRIP menu is displayed. Use w / x to scroll through the following menu items: . Speed Timer


. Navigation . Speed, Fuel Range,


Instantaneous Fuel Economy Trip 1 or Trip 2, Average Fuel Economy, Average Vehicle Speed


. Power Flow (eAssist Only)


Speed The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.


Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (26,1)


5-26


Instruments and Controls


Navigation This display is used for the navigation system Turn-by-Turn guidance. See the navigation manual, if the vehicle has navigation, for more information.


Speed, Fuel Range, Instantaneous Fuel Economy The top of this display includes a digital speedometer. The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset. In the center of the page is the fuel range display. This shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. This display is shown as l . km (mi). Fuel range cannot be reset.


Also included on this page is an instantaneous fuel economy display. The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. This display is shown as . L/100 km (mpg). This display cannot be reset.


Trip 1 or Trip 2, Average Fuel Economy, Average Vehicle Speed This displays the current distance traveled, in either kilometers (km) or miles (mi), from the last reset for the trip odometer. The trip odometer can be reset to zero by pressing and holding the SET/CLR button while the trip odometer display is showing.


The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. This display is shown as . c L/100 km (mpg). Reset the average consumption by pressing SET/CLR when it is displayed. This screen also displays the average vehicle speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is based on the various vehicle speeds recorded since the last reset. This display is shown as c km/h (mph). Reset the average speed by pressing SET/CLR when it is displayed.


Power Flow (eAssist Only) This display shows the operating mode of the eAssist system and the high voltage battery charge level. The animation indicates the direction of energy flow.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (27,1)


Instruments and Controls


5-27


Vehicle Information Menu (OPTION) Items Press MENU on the turn signal lever until the OPTION menu is displayed. Use w / x to scroll through the following menu items: . Unit


Tire Pressure


. Remaining Oil Life


Jump Start (eAssist Only)


Unit Move w / x to switch between metric or US when the Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.


Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed


in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System on page 10‑50 and Tire Pressure Monitor Operation on page 10‑51 for more information.


Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑31. The oil should be changed as soon as possible. See Engine Oil on page 10‑10. In addition to the Engine Oil Life System monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11‑3 for more information.


Remember, the Remaining Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Remaining Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the Engine Oil Life System, press SET/ CLR while the Remaining Oil Life display is active. See Engine Oil Life System on page 10‑12.


Jump Start (eAssist Only) This display allows for on-board jump starting of the vehicle. See “Jump Starting (On-board with eAssist Only)” for more information. ECO Drive Assist Menu (ECO) Items This menu is only available on some vehicles. Press MENU on the turn signal lever until ECO Menu is displayed. Use w / x to scroll through the following menu items: . Best Average Fuel Economy


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (28,1)


5-28


Instruments and Controls


. ECO Index


Top Consumers


Best Average Fuel Economy The right hand side displays the best average fuel economy (AFE) that is achieved for a selected distance. The left hand side displays a running average of fuel economy for the most recently traveled selected distance. The center bar graph displays the instantaneous fuel economy. Quickly press the SET/CLR button to display a page for selecting one of the distance options. Move the up/down arrow to choose the selection, and SET/CLR to change the setting. When viewing best AFE, a several second press and hold of SET/CLR will reset the best value. The best value will show “-.-“ until the selected distance has been traveled. The display provides feedback on how current driving behavior in the bar graph affects the running


average in the left display and how well recent driving compares to the best that has been achieved.


ECO Index This display shows a bar graph that indicates how efficiently the vehicle is being driven. For the most efficient use of fuel, only the lower portion of the graph should be filled. Instant economy is also shown in L/ 100 km (mpg). If the vehicle has a manual transmission, this display also includes an up-shift indicator.


Top Consumers This display shows a list of the features that are currently impacting the fuel economy, in order from highest to lowest. If a feature is turned off, it will be removed from the list. Compass The vehicle has a compass display in the DIC. See Compass on page 5‑4 for more information.


Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (29,1)


Instruments and Controls


5-29


Battery Voltage and Charging Messages


BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑26. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.


Brake System Messages


BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑24. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the electric parking brake without the brake pedal applied. See Parking Brake on page 9‑32 for more information. RELEASE PARK BRAKE SWITCH This message is displayed if the electric parking brake is on while the vehicle is in motion. Release it before you attempt to drive. See Parking Brake on page 9‑32 for more information. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When


this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service. SERVICE PARKING BRAKE This message is displayed when there is a problem with the electric parking brake. See Parking Brake on page 9‑32 for more information. Take the vehicle to your dealer.


Compass Messages


CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5‑4. – – Dashes will be displayed if the compass needs service. See your dealer for service.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (30,1)


5-30


Instruments and Controls


Door Ajar Messages


DRIVER DOOR OPEN This message will display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message will display when the driver side rear door is open. Close the door completely. PASSENGER DOOR OPEN This message will display when the front passenger door is open. Close the door completely. RIGHT REAR DOOR OPEN This message will display when the passenger side rear door is open. Close the door completely.


TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.


Engine Cooling System Messages


A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. The vehicle can continue to be driven. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.


COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10‑17. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (31,1)


HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10‑20.


Engine Oil Messages


CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑12, Driver Information Center (DIC) on page 5‑24, Engine Oil on page 10‑10, and Maintenance Schedule on page 11‑3. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.


Instruments and Controls


5-31


ENGINE OIL LOW — ADD OIL On some vehicles, this message may display when the engine oil level is too low. Check the oil level. See Engine Oil on page 10‑10. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.


Engine Power Messages


ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the


next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.


Fuel System Messages


FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.


Key and Lock Messages


NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with keyless access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (32,1)


5-32


Instruments and Controls


REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2‑3.


Object Detection System Messages


PARK ASSIST OFF This message displays when the parking assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9‑43.


SERVICE PARKING ASSIST This message displays if there is a problem with the parking assist system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9‑43 for more information.


Ride Control System Messages


SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start


the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. SPORT MODE ON This message displays when using the interactive drive control. See Interactive Drive Control System (except GS) on page 9‑38 or Interactive Drive Control System (GS Only) on page 9‑40 for more information. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly. TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (33,1)


Instruments and Controls


5-33


Security Messages


THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.


Starting the Vehicle Messages


JUMP START ACTIVE WAIT TO START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).” JUMP START COMPLETE ATTEMPT START This message displays while performing an on-board jump start of the vehicle. See “Jump Starting (On-board with eAssist Only).”


JUMP START DISABLED SEE OWNERS MANUAL This message displays if there is a problem with the on-board jump start system, or the 12 volt battery is too low to perform an on-board jump start. Try using jumper cables and performing a normal jump start. See “Jump Starting (On-board with eAssist Only).” Take the vehicle to your dealer for service if this message continues to be displayed.


Tire Messages


SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑51.


TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑51. TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑22. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑41, Vehicle Load Limits on page 9‑10, and Tire Pressure on page 10‑48.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (34,1)


5-34


Instruments and Controls


You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the SET/CLR button. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5‑24.


Transmission Messages


SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park).


TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.


Window Messages


OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to reprogram each front window for the express-up feature to work. See Power Windows on page 2‑17.


Vehicle Personalization The audio system controls are used to access the personalization menus for customizing vehicle features. CONFIG (Configuration): Press to access the Configuration Settings menu. Multifunction Knob: Press the center of this knob to enter the menus and select menu items. Turn the knob to scroll through the menus. BACK: Press to exit or move backward in a menu.


Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu. 2. Turn the Multifunction knob to


highlight Vehicle Settings.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (35,1)


Instruments and Controls


5-35


3. Press the center of the


Multifunction knob to select the Vehicle Settings menu.


The following list of menu items will be available: . Climate and Air Quality . Comfort and Convenience


Languages Lighting


. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings Turn the Multifunction knob to highlight the menu. Press the knob to select it. Each of the menus is detailed in the following information. Climate and Air Quality Select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Speed . Auto Compartment Zone Temp


. Remote Start Auto Heat Seats . Auto Defog . Auto Rear Defog


Auto Fan Speed This allows selection of the automatic fan speed to run lower or higher than normal. Press the Multifunction knob when Auto Fan Speed is highlighted to open the menu. Turn the knob to highlight High, Medium, or Low. Press the knob to confirm the selection and move back to the last menu.


Auto Compartment Zone Temp This allows the selection of how the climate control system will operate upon vehicle start. Selecting Single Zone automatically resets the passenger temperature setting the same as the driver's for every vehicle start. The climate control system will operate using only the driver's setting until the passenger temperature setting is changed.


Selecting Dual Zone or Last Setting will keep the passenger temperature adjustment separate from the driver's setting all the time. Press the Multifunction knob when Auto Compartment Zone Temp is highlighted. Turn the knob to highlight Single Zone, Dual Zone, or Last Setting. Press the knob to confirm the selection and go back to the last menu.


Remote Start Auto Heat Seats When on, this feature will turn the heated seats on when using remote start on cold days. Press the Multifunction knob when Remote Start Auto Heat Seats is highlighted. Turn the knob to highlight On or Off. Press the knob to confirm the selection and go back to the last menu.


Auto Defog This allows the auto defog function to be turned on or off.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (36,1)


5-36


Instruments and Controls


Press the Multifunction knob when Auto Defog is highlighted to select On or Off. Turn the knob to confirm the selection and move back to the last menu.


Auto Rear Defog This allows the auto rear defog to be turned on or off. This feature will automatically turn on the rear defogger when it is cold outside. Press the Multifunction knob when Auto Rear Defog is highlighted to select On or Off. Turn the knob to confirm the selection and move back to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and the following will be displayed: . Chime Volume . Button Chime


Chime Volume This allows the selection of the chime volume level.


Press the Multifunction knob when Chime Volume is highlighted. Turn the knob to select Normal or High. Press the knob to confirm and go back to the last menu.


Button Chime This allows Button Chime to be turned on or off. Press the Multifunction knob when Button Chime is highlighted to select On or Off. Turn the knob to confirm the selection and move back to the last menu. Language Select the Language menu and the following will be displayed: . English


Francais Canadien . Espanol Mexicano Turn the Multifunction knob to select the language. Press BACK to return to the last menu.


Lighting Select the Lighting menu and the following will be displayed: . Vehicle Locator Lights . Exit Lighting


Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. Press the Multifunction knob when Vehicle Locator Lights is highlighted to select On or Off. Turn the knob to confirm and go back to the last menu.


Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the Multifunction knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds, 1 Minute, or 2 Minutes. Press the knob to confirm and go back to the last menu.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (37,1)


Instruments and Controls


5-37


Power Door Locks Select Power Door Locks and the following will be displayed: . Open Door Anti Lock Out . Auto Door Unlock . Delay Door Lock


Open Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available and the door will lock as programmed through this menu. Press the Multifunction knob when Open Door Anti Lock Out is highlighted to select On or Off. Turn the knob to confirm and go back to the last menu.


Auto Door Unlock This allows selection of which doors will automatically unlock when the vehicle is shifted into P (Park).


Press the Multifunction knob when Auto Door Unlock is highlighted. Turn the knob to select All Doors, Driver Door, or Off. Press the knob to confirm and go back to the last menu.


Delay Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. You will hear three chimes to signal delayed locking is in use. Press either the power door lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors. Press the Multifunction knob when Delay Door Lock is highlighted to select On or Off. Press BACK to return to the last menu.


Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following will be displayed: . Remote Unlock Light Feedback . Remote Lock Feedback . Remote Door Unlock . Passive Door Unlock . Passive Door Lock . Remote Left In Vehicle


Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Press the Multifunction knob when Remote Unlock Light Feedback is highlighted to select On or Off. Turn the knob to confirm and go back to the last menu.


Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (38,1)


5-38


Instruments and Controls


Press the Multifunction knob when Remote Lock Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press the knob to confirm and go back to the last menu.


Remote Door Unlock This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press the Multifunction knob when Remote Door Unlock is highlighted. Turn the knob to select Driver Door or All Doors. When set to Driver Door, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press the Multifunction knob to confirm and go back to the last menu.


Passive Door Unlock This allows selection of which doors are unlocked by pressing the button on the outside door handle. Press the Multifunction knob when Passive Door Unlock is highlighted. Turn the knob to select All Doors or Driver Door. Press the knob to confirm and go back to the last menu.


Passive Door Lock This allows selection of what type of feedback is given when locking the vehicle. Press the Multifunction knob when Passive Door Lock is highlighted. Turn the knob to select On with Horn Chirp, ON, or OFF. Press the knob to confirm and go back to the last menu.


Remote Left In Vehicle This allows the Remote Left In Vehicle reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press the Multifunction knob when Remote Left In Vehicle is highlighted. Turn the knob to select On or Off. Press the knob to confirm and go back to the last menu. Return to Factory Settings Select Return to Factory Settings to return all of the vehicle personalization to the default settings. Turn the knob to select Yes or No. Press the knob to confirm and go back to the last menu.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (39,1)


Universal Remote System See Radio Frequency Statement on page 13‑20 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.


Universal Remote System Programming


If the vehicle has this feature, you will see these buttons with one indicator light next to them in the overhead console. This system provides a way to replace up to three remote control transmitters used to activate


Instruments and Controls


5-39


devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1,1982. Read the instructions completely before attempting to program the Universal Remote system. Because of the steps involved, it may be helpful to have another person available to assist with programming the Universal Remote system. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Remote system programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Remote system buttons be erased for security purposes. See “Erasing Universal Remote System Buttons” later in this section.


When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate being programmed. It is recommended that a new battery be installed in the hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (40,1)


5-40


Instruments and Controls


To program up to three devices: 1. Hold the end of the hand-held


transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver (motor-head unit).


2. At the same time, press and


hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release the Universal Remote system button or the hand-held transmitter button until the indicator light changes from a slowly to a rapidly flashing light. You now may release both buttons.


Some entry gates and garage door openers may require substitution of Step 2 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.


3. Press and hold for five seconds


the newly trained Universal Remote system button (the button selected in Step 2) while observing the indicator light and garage door activation.


If the indicator light stays on continuously or the garage door starts to move when the Universal Remote system button is pressed and released, then the programming is complete. There is no need to continue programming Steps 4–6.


If the Universal Remote system indicator light blinks rapidly for two seconds, then turns to a constant light and the garage door does not move, continue with programming Steps 4–6. It may be helpful to have another person assist with the remaining Steps 4–6.


“Learn” or “Smart” Button


4. After Steps 1–3 have been


completed, locate the “Learn” or “Smart” button inside the garage on the garage door opener receiver (motor-head unit). The name and color of the button may vary by manufacturer.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (41,1)


Instruments and Controls


5-41


To program the remaining two Universal Remote system buttons, begin with Step 1 of “Programming the Universal Remote System.” Gate Operator and Canadian Programming If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner.


If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming the Universal Remote System” procedures, regardless of where you live, replace Step 2 under “Programming the Universal Remote System” with the following: Continue to press and hold the Universal Remote system button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.


5. Firmly press and release the


6.


“Learn” or “Smart” button. After pressing this button, you will have 30 seconds to complete Step 6. Immediately return to the vehicle. Firmly press and hold for two seconds the Universal Remote system button, selected in Step 2 to control the garage door, and then release it. If the garage door does not move or the lamp on the garage door opener receiver (motor-head unit) does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release.


The Universal Remote system should now activate the garage door.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (42,1)


5-42


Instruments and Controls


Universal Remote System Operation


Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. To erase all programmed buttons on the Universal Remote system device: 1. Press and hold down the two


outside buttons until the indicator light begins to flash. This should take about 10 seconds.


2. Release both buttons.


Reprogramming a Single Universal Remote System Button To reprogram any of the three Universal Remote system buttons: 1. Press and hold the desired


Universal Remote system button. Do not release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.” If you have questions or need help programming the Universal Remote system, call 1-800-355-3515 or go to www.homelink.com. You may also call the customer assistance phone number under Customer Assistance Offices (U.S. and Canada) on page 13‑5 or Customer Assistance Offices (Mexico) on page 13‑5.


Buick Regal Owner Manual - 2013 - crc - 11/5/12


Black plate (1,1)


Lighting


Exterior Lighting


Exterior Lighting


Exterior Lamp Controls


Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off


Reminder . . . . . . . . . . . . . . . . . . . . 6-2


Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running


Lamps (DRL) . . . . . . . . . . . . . . . . 6-2


Automatic Headlamp


System . . . . . . . . . . . . . . . . . . . . . . 6-2
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 6-3
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-4


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 6-4
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-5


Lighting Features


Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-6
Battery Power Protection . . . . . . 6-6


The exterior lamp control is on the instrument panel on the outboard side of the steering wheel. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode. In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park) on


Lighting


6-1


automatic transmission vehicles, and when the parking brake is released on manual transmission vehicles. AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps together with the following: . Sidemarker Lamps


Taillamps License Plate Lamps Instrument Panel Lights


2 (Headlamps): Turns on the headlamps together with the following: . Sidemarker Lamps


Taillamps License Plate Lamps Instrument Panel Lights


. Parking Lamps

Loading...
x